Login- Download PDF Manual
-
130 mph (210 km/h)
149 mph (240 km/h)
Above 149 mph (240 km/h)
G201003AEN 3.Checking tire life (TIN :Tire
Identification Number)
Any tires that are over 6 years old, based on the manufacturing date, (including the spare tire) should be replaced by new ones. You can find the manufacturing date on the tire sidewall (possibly on the inside of the wheel), displaying the DOT Code. The DOT Code is a series of num- bers on a tire consisting of numbers and English letters. The manufactur- ing date is designated by the last four digits (characters) of the DOT code.
DOT : XXXX XXXX OOOO The front part of the DOT means a plant code number, tire size and tread pattern and the last four num- bers indicate week and year manu- factured. For example: DOT XXXX XXXX 1612 represents that the tire was produced in the 16th week of 2012.
42
G201004AEN 4.Tire ply composition and material The number of layers or plies of rub- ber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. The letter "R" means radial ply con- struction; the letter "D" means diago- nal or bias ply construction; and the letter "B" means belted-bias ply con- struction.
G201005AUN 5.Maximum permissible inflation
pressure
This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label inflation pressure.
for recommended
G201006AUN 6.Maximum load rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.
the
G2010007AEN-EU 7.Uniform tire quality grading Quality grades can be found where applicable on tire sidewall between tread shoulder and maxi- mum section width. For example: TREAD wear 200 TRACTION AA TEMPERATURE A
Maintenance
Tread wear The tread wear grade is a compara- tive rating based on the wear rate of the tire when tested under controlled conditions on a specified govern- ment test course. For example, a tire graded 150 would wear one-and-a- half times (1½) as well on the gov- ernment course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. These grades are molded on the side-walls of passenger vehicle tires. The tires available as standard or optional equipment on your vehicle may vary with respect to grade.
7 43
WARNING - Tire
temperature
The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat build-up and possible sudden tire failure. This can cause loss of vehicle control and serious injury or death.
Maintenance
Traction - AA, A, B & C The traction grades, from highest to lowest, are AA, A, B and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on spec- ified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perform- ance.
WARNING
The traction grade assigned to this tire is based on straight- ahead braking traction tests, and does not include accelera- tion, cornering, hydroplaning, or peak traction characteristics.
Temperature -A, B & C The temperature grades are A (the highest), B and C representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled condi- tions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C cor- responds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the labora- tory test wheel than the minimum required by law.
44
G201100ABH Tire terminology and definitions Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilo- pascal (kPa). Accessory Weight: This means the combined weight of optional acces- sories. Some examples of optional accessories are, automatic transmis- sion, power seats, and air condition- ing. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.
Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilo- pascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric des- ignator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the Front Axle. GAWR RR: Gross Axle Weight Rating for the Rear axle.
Maintenance
Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number ranging from 1 to 279 that corre- sponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maxi- mum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum per- missible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150
pounds (68 kg).7 45
Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: Load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occu- pant weight and dividing by 2. Vehicle Placard: A label permanent- ly attached to a vehicle showing the original equipment tire size and rec- ommended inflation pressure.
Maintenance
Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a par- ticular side that faces outward when mounted on a vehicle. The outward facing sidewall bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the inner facing sidewall. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommend- ed tire inflation pressure and shown on the tire placard. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead.
Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, tempera- ture and treadwear. Ratings are determined by tire manufacturers using government testing proce- dures. The ratings are molded into the sidewall of the tire. Vehicle Capacity Weight: The num- ber of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo and luggage load.
46
All season tires HYUNDAI specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi- tions. All season tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas.
Summer tires HYUNDAI specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rat- ing M+S (Mud and Snow) on the tire side wall. If you plan to operate your vehicle in snowy or icy conditions, HYUNDAI recommends the use of snow tires or all season tires on all four wheels.
Maintenance
Snow tires If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; other- wise, poor handling may result. Snow tires should carry 4 psi (28
kPa) more air pressure than the pressure recommended for the stan- dard tires on the tire label on the dri- ver's side of the center pillar, or up to the maximum pressure shown on the tire sidewall, whichever is less. Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.7 47
Maintenance
Tire chains Tire chains, if necessary, should be installed on the drive wheels (rear wheels). Be sure that the chains are installed in accordance with the manufactur- er's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed.
48
WARNING - Snow or ice
(cid:129) When driving on roads cov- ered with snow or ice, drive at less than 20 mph (30 km/h).
(cid:129) Use the SAE “S” class or wire
chains.
(cid:129) If you hear noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. (cid:129) To prevent body damage, retighten the chains after driv- ing 0.3~0.6 miles (0.5~1.0 km). (cid:129) Do not use tire chains on vehicles equipped with alu- minum wheels. In unavoid- able circumstance, use a wire type chain.
(cid:129) Use wire chains less than 0.47
inches (12 mm) to prevent damage to the chain’s con- nection.Radial-ply tires Radial-ply tires provide improved tread life, road hazard resistance and smoother high speed ride. The radial- ply tires used on this vehicle are of belted construction, and are selected to complement the ride and handling characteristics of your vehicle. Radial- ply tires have the same load carrying capacity, as bias-ply or bias belted tires of the same size, and use the same recommended inflation pressure. Mixing of radial-ply tires with bias-ply or bias belted tires is not recommended. Any combinations of radial-ply and bias-ply or bias belted tires when used on the same vehicle will seriously dete- riorate vehicle handling. The best rule to follow is: Identical radial-ply tires should always be used as a set of four. Longer wearing tires can be more susceptible to irregular tread wear. It is very important to follow the tire rotation interval shown in this section to achieve the tread life potential of these tires. Cuts and punctures in radial-ply tires are repairable only in the tread area, because of sidewall flexing. Consult your tire dealer for radial-ply tire repairs.
FUSES Blade type
Normal
Cartridge type
Blown
Normal
Blown
Fusible link
Normal
Blown
OBH072060
G210000ABH-EU A vehicle’s electrical system is protected from electrical overload damage by fuses.
This vehicle has 4 fuse panels, two locat- ed in the driver’s side and passenger’s side panel bolster, the others are in the engine compartment. If any of your vehicle’s lights, acces- sories, or controls do not work, check the appropriate circuit fuse. If a fuse has blown, the element inside the fuse will be melted. If the electrical system does not work, first check the driver’s side fuse panel. Before replacing a blown fuse, discon- nect the negative battery cable. Always replace a blown fuse with one of the same rating. If the replacement fuse blows, this indi- cates an electrical problem. Avoid using the system involved and immediately consult an authorized HYUNDAI dealer. Three kinds of fuses are used:blade type for lower amperage rating, cartridge type, and fusible link for higher amperage rat- ings.
Maintenance
WARNING - Fuse replace-
ment
(cid:129) Never replace a fuse with any- thing but another fuse of the same rating.
(cid:129) A higher capacity fuse could cause damage and possibly a fire.
(cid:129) Never install a wire or aluminum foil instead of the proper fuse - even as a temporary repair. It may cause extensive wiring damage and a possible fire.
CAUTION
Do not use a screwdriver or any other metal object to remove fuses because it may cause a short circuit and damage the system.
✽✽ NOTICE The actual fuse/relay panel label may differ from equipped items.
7 49
Maintenance
CAUTION
(cid:129) When replacing a blown fuse or relay with a new one, make sure the new fuse or relay fits tightly into the clips The incomplete fas- tening fuse or relay may cause the vehicle wiring and electric sys- tems damage and a possible fire. (cid:129) Do not remove fuses, relays and terminals fastened with bolts or nuts.The fuses,relays and termi- nals may be fastened incomplete- ly, and it may cause a possible fire.If fuses,relays and terminals fastened with bolts or nuts are blown, consult an authorized HYUNDAI dealer.
(cid:129) Do not input any other objects except fuses or relays into fuse/relay terminals such as a driv- er or wiring.It may cause contact failure and system malfunction.
50
Front passenger’s side Driver’s side
Front passenger’s side
OBH078019
OBH078020
G210100ABH Inner panel fuse replacement 1. Turn the ignition switch and all other
switches off.
2. Open the fuse panel cover.
OBH078021
3. Pull the suspected fuse straight out. Use the removal tool provided in the front passenger’s side panel.4. Check the removed fuse; replace it if it
is blown. Spare fuses are provided in the pas- senger compartment panel fuse pan- els (or in the engine compartment fuse panel).
5. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer. If you do not have a spare, use a fuse of the same rating from a circuit you may not need for operating the vehicle, such as the cigarette lighter fuse.
If the headlights or other electrical com- ponents do not work and the fuses are OK, check the fuse panel in the engine compartment. If a fuse is blown, it must be replaced.
Maintenance
✽✽ NOTICE • If the memory fuse is pulled up from the fuse panel, the warning chime, audio, clock and interior lamps, etc., will not operate. Some items must be reset after replacement. Refer to “Battery” in this section.
• Even when the memory fuse is pulled up, the battery can still be discharged by operation of the headlights or other electrical devices.
7 51
OBH048020
G210101AUN Memory fuse Your vehicle is equipped with a memory fuse to prevent battery discharge if your vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods. 1. Turn off the engine. 2. Turn off the headlights and tail lights. 3. Open the driver’s side panel cover and
pull up the memory fuse.
Maintenance
3. Check the removed fuse; replace it if it is blown. To remove or insert the fuse, use the fuse puller in the front passen- ger’s side panel.
4. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer.
CAUTION
After checking the fuse panel in the engine compartment, securely install the fuse panel cover. If not, electrical failures may occur from water contact.
OBH071023
OBH071024
G210200AEN Engine compartment fuse replacement 1. Turn the ignition switch and all other
switches off.
2. Remove the fuse panel cover by
pressing the tab and pulling up.
52
OBH078025
G210201ABH Main fuse If the main fuse is blown, it must be removed as follows: 1. Remove the fuse panel cover on the right side in the engine compartment. 2. Remove the nuts shown in the picture
above.
3. Replace the fuse with a new one of the
same rating.
4. Reinstall in the reverse order of
removal.
✽✽ NOTICE If the main fuse is blown, consult an authorized HYUNDAI dealer.
Maintenance
G210300ABH-EU Fuse/relay panel description Inside the fuse/relay panel covers, you can find the fuse/relay label describing fuse/relay name and capacity.
Inner panel fuse panel Driver’s side
Engine compartment fuse panel
✽✽ NOTICE Not all fuse panel descriptions in this manual may be applicable to your vehi- cle. It is accurate at the time of printing. When you inspect the fuse panel in your vehicle, refer to the fuse panel label.
Front passenger’s side
OBH071026/OBH071027/OBH071028/OBH071029
7 53
Maintenance
Instrument panel (Driver’s side fuse panel)
Protected component Driver Power Window Module, Rear Power Window Module LH Passenger Power Window Module, Rear Power Window Module RH Console Switch LH/RH, ECS Control Module, Steering Angle Sensor, Key Lock Module,Tire Pressure Monitoring Module
Multifunction Switch, Crash Pad Switch, A/C Control Module, Instrument Cluster, Rear Seat Warmer Module LH, Driver Seat Warmer Module Rear Seat Warmer Module RH, Passenger Seat Warmer Module, Passenger CCS Control Module, Driver CCS Control Module, Generator Transmission Range Switch Fob Holder, Start Stop Button Switch Instrument Cluster (IND.) A/C Control Module Start Stop Button Switch, Door Warning Switch, Fob Holder, Key Solenoid E/R Junction Box Fuse (INHIBITOR SW 15A, ECU-2 10A, EHPS 10A, CRUISE 10A, TCU 15A, ESP 10A,STOP LP 10A, AFLS 10A)
Intelligent Accel Pedal Unit
Driver Door Module Stop Lamp Switch Instrument Cluster (Air Bag IND.) Auto Head Lamp Leveling Device Sensor, Adaptive Front Lighting Module, Head Lamp LH, Head Lamp RH PDM Data Link Connector, Auto Light Sensor & Security Indicator, Rear Door Module LH/RH,Shift Lock
Description
Fuse rating
30A 30A
10A
10A
10A 10A 10A 10A 10A
30A
10A
10A 10A 10A
10A
10A 10A
P/WDW(LH) P/WDW(RH)
MODULE 2
CURISE SW
START PDM 2
CLUSTER A/CON(IG1) KEY ILLUMINATIONIG KEY SUPPLY
INTELLIGENT A/PEDAL DR LOCK DRV STOP LP A/BAG IND
AFLS
PDM 1
SECURITY LP54
Maintenance
Description
Fuse rating
Protected component
MODULE 1
MODULE 3
P/HANDLE ECS A/BAG
AUDIO(B+)
S/HEATER DRV P/TRUNK F/LID AUDIO(IG1) RF RECEIVER A/CON(B+) I.O.D
10A
10A
15A 15A 15A
15A
15A 30A 10A 10A 10A 10A 30A
FAM, IPM, Tilt & Telescopic Module, PDM, Driver Door Module, Passenger Door Module, IMS Control Module, Multifunction Switch, Electronic Parking Brake Module, Power Trunk Lid Control Module, Forward & Rear Parking Assist Control Module
FAM, Multifunction Switch, Tilt & Telescopic Module, Instrument Cluster, Driver Door Module, Passenger Door Module, Power Trunk Lid Control Module, IMS Control Module, Rear Curtain Module Tilt & Telescopic Module ECS Control Module SRS Control Module Audio, Front Monitor, AV Head Module, Rear Monitor (With AV), Rear Audio Switch, Media Module (With AV) Driver CCS Control Module, Driver Seat Warmer Module (W/O CCS) Power Trunk Lid Control Module Trunk Lid & Fuel Filler Door Switch (Fuel Filler Door Switch) AV Head Module, Audio, Active Headrest Sensor Module RF Receiver A/C Control Module,Tire Pressure Monitoring Module I/P Junction Box LH Fuse (MODULE 3 10A, AUDIO(B+) 15A ,Rf Receiver 10A , A/CON(IG1) 15A)
7 55
Maintenance
Instrument panel (Passanger’s side fuse panel)
Description
Fuse rating
Protected component
10A 10A 30A 20A 10A 10A 20A 20A 10A 10A 20A 15A 20A 15A 15A 10A 10A 25A 10A
Rear Curtain Module Driver Door Module, Passenger Door Module E/R Junction Box Fuse (AQS 10A, WASHER 15A) Overhead Console Lamp Console Switch LH/RH, Piezo Buzzer Active Incar Sensor, A/C Control Module Passenger Power Seat Relay Box Rear Seat Warmer Module LH/RH, Rear Power Seat Control Switch Instrument Cluster, Rheostat, Driver CCS Control Module, Passenger CCS Control Module, PDM, IPM Electro Chromic Mirror, Overhead Console Lamp, Rain Sensor, Rear Curtain Module, Camera Module Passenger CCS Control Module, Passenger Seat Warmer Module Passenger Door Module Rear Power Seat Relay Box, Rear Slide Limit Switch LH Steering Wheel Heater Rear Accessory Socket ACC Socket Relay A/C Control Module, IPM, PDM, Key Lock Module PDM Audio, Camera Module, Rear Audio Switch, Front Monitor, Media Module, AV Head Module
CURTAIN (RR) MIRROR IG KEY SUPPLY SUNROOF CONSOLE SW A/CON(IG2) P/SEAT PASS S/HEATER RR MODULE 1
MODULE 3
S/HEATER PASS DR LOCK PASS P/SEAT RR HTD STRG P/OUTLET RR P/OUTLET FRT MODULE 2
PDM AUDIO56
Maintenance
Engine compartment fuse panel
Description
Fuse rating
ALT I/P LH PWR I/P RH PWR C/FAN EHPS AIR ECS AMP 1
AMP 2
PDM(ACC) VDC/ESC 1
VDC/ESC 2
PDM(IG1) PDM(IG2) P/SEAT DRV H/LP WASHER VACUUM PUMP P/OUTLET FRT TRUNK IMS STOP LP B/UP LP200A 60A 60A 60A 80A 40A 40A 30A 30A 30A 30A 30A 30A 30A 20A 20A 25A 10A 10A 10A 10A
Protected component
Generator I/P Junction Box LH I/P Junction Box RH Cooling Fan Relay EHPS Module ECS Compressor Relay AV JBL AMP AMP PDM (ACC) Relay VDC/ESC Control Module, Multipurpose Check Connector VDC/ESC Control Module, Multipurpose Check Connector PDM (IG1) Relay PDM (IG2) Relay Driver Power Seat Relay Box, IMS Control Module, Driver Lumbar Support Switch Head Lamp Washer Relay Brake Vacuum Pump Relay ACC Socket Relay Trunk Lid Relay Stop Lamp Relay, Stop Lamp Switch, IPM Rear Combination Lamp LH/RH (IN), Electro Chromic Mirror, Camera Module, Rear Curtain Module
7 57
Maintenance
Description
Fuse rating
Protected component
30A 40A
40A
40A
40A
10A 15A 15A 15A 10A 10A 15A 15A 30A 10A 15A 10A 10A 10A 10A 20A 15A
Engine Control Relay Blower Relay
Ignition Switch (IG 2, START), Presafety Seat Belt Passenger
E/R Junction Box Fuse (AQS 10A, WASHER 15A)
Ignition Switch (IG 1, ACC), Presafety Seat Belt Driver
A/C Control Module Electric Parking Brake Module Electric Parking Brake Module Horn Relay IPM, Head Lamp (Low) Relay AQS Sensor, Electronic Control Wiper Module, Blower Relay Heated Glass (FR) Relay Washer Relay Wiper Motor A/C Control Module, Power Outside Mirror & Mirror Folding Motor LH/RH TCM Head Lamp LH/RH EHPS Module ESC Control Module, Multipurpose Check Connector ECM Ignition Coil #1,2,3,4,5,6
Injector Drive BoxECU BLOWER IGN SW 2 (PRESAFETY PASS) RR HTD IGN SW 1 (PRESAFETY DRV) A/CON EPB 1
EPB 2
HORN IPM AQS DEICER WASHER WIPER HTD MIRR TCU AFLS EHPS VDC/ESC ECU(IG1) IGN COIL INJECTOR(B+)58
Maintenance
Description
Fuse rating
Protected component
SENSOR 1
SENSOR 2
SENSOR 3
H/LP RH H/LP LH INJECTOR(IG1) CRUSIE STOP LP ECU(B+) ROOM LP F/PUMP START10A
10A
10A 15A 15A 10A 10A 10A 15A 10A 20A 30A
ECM, Mass Air Flow Sensor, Oxygen Sensor #1,2,3,4
Canister Purge Control Solenoid Valve, Variable Intake Manifold Valve, Oil Control Valve, ECM, Cooling Fan Relay, Immobilizer Module, Fuel Pump Resister ECM, Injector #1~#6, Fuel Pump Relay Head Lamp RH Head Lamp LH Injector Drive Box Smart Cruise Control Module Stop Lamp Switch, Stop Lamp Relay, Generator,Vacuum Sw ECM,TCM,Injector Drive Box Room Lamp Relay Fuel Pump Relay Start Solenoid7 59
Maintenance
LIGHT BULBS G220000AEN
WARNING - Working on
the lights
Prior to working on the light, firmly apply the parking brake, ensure that the ignition switch is turned to the LOCK position and turn off the lights to avoid sudden movement of the vehicle and burning your fin- gers or receiving an electric shock.
Use only the bulbs of the specified wattage.
CAUTION
Be sure to replace the burned-out bulb with one of the same wattage rating. Otherwise, it may cause damage to the fuse or electric wiring system.
CAUTION
If you don’t have necessary tools, the correct bulbs and the expertise, consult an authorized HYUNDAI dealer.In many cases,it is difficult to replace vehicle light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true if you have to remove the head- light assembly to get to the bulb(s). Removing/installing the headlight assembly can result in damage to the vehicle.
✽✽ NOTICE After driving in rain or washing, the headlight and taillight lenses could appear frosty. This condition is caused by the temperature difference between the lamp inside and outside. This is similar to the condensation on your windows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an authorized HYUNDAI dealer.
60
OBH071053
G220100BBH Headlight, position light, turn sig- nal light, side marker light and front fog light bulb replacement (1) Headlight (High) (2) Headlight (Low) (3) Front side marker light (4) Front turn signal light (5) Position light (6) Front fog light (if equipped)
(Continued) (cid:129) If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.
(cid:129) Wear eye protection when chang- ing a bulb. Allow the bulb to cool down before handling it.
OHD076046
Headlight (HID type) bulb replace- ment (if equipped) If the light bulb is not operating, have the vehicle checked by an authorized HYUNDAI dealer.
G220101AUN-EU Headlight bulb
WARNING - HID Headlight low beam (if equipped)
Do not attempt to replace or inspect the low beam (XENON bulb) due to electric shock danger. If the low beam (XENON bulb) is not working, have your vehicle checked by an authorized HYUNDAI Dealer.
WARNING - Halogen bulbs (cid:129) Halogen bulbs contain pressur- ized gas that will produce small pieces of glass if broken.
(cid:129) Always handle the bulbs careful- ly, and avoid scratches and abra- sions. If the bulbs are lit, avoid contact with liquids.
(cid:129) Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
(Continued)
Maintenance
CAUTION
If your vehicle is equipped with High Intensity Discharge (HID) headlights, these headlights con- tain mercury.So if you need to have your vehicle disposed, you should remove the HID Headlights before disposal. The removed HID head- lights should be recycled, re-used or disposed as hazardous waste.
✽✽ NOTICE HID lamps have superior performance vs. halogen bulbs. HID lamps are esti- mated by the manufacturer to last twice as long or longer than halogen bulbs depending on their frequency of use. They will probably require replacement at some point in the life of the vehicle. Cycling the headlamps on and off more than typical use will shorten HID lamp life. HID lamps do not fail in the same manner as halogen incandescent lamps. If a headlamp goes out after a period of operation but will immediately relight when the headlamp switch is cycled it is likely the HID lamp needs to be replaced. HID lighting components are more com- plex than conventional halogen bulb and thus have higher replacement cost.
7 61
Maintenance
G220102ABH-EU Headlight (bulb type),front turn sig- nal,position,side marker and fog light bulbs (if equipped) If the light bulb is not operating, have the vehicle checked by an authorized HYUNDAI dealer.
62
OBH078031
OBH071032
G220200AEN Side repeater light bulb replace- ment (if equipped) If the light bulb is not operating, have the vehicle checked by an authorized HYUNDAI dealer.
G220300ABH Rear combination light bulb replacement (1) Back-up light (2) Rear turn signal light (3) Stop and tail light (4) Rear side marker light (5) Tail light
3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it counter- clockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
5. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
6. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.
7. Install the service cover by putting it
into the service hole.
Back-up,stop and tail light If the light is not operating, have the vehi- cle checked by an authorized HYUNDAI dealer.
OBH078033
OBH078034
Rear turn signal light 1. Open the trunk lid. 2. Remove the service cover by pulling out
the service cover.
Maintenance
OBH078035
OBH072101N
High mounted stop light 1.Remove the rear seat 1.Disconnect the negative battery cable. 2.Remove the rear seat cushion.
7 63
Maintenance
3.Loosen
the mounting bolts,
remove the rear seat back.
OBH072102N then
4.Disconnect the connector.
OVI071123N
OVI071124N 5.Push the hook, disconnect the main
connector.
Tightening torque : 34.3~53.9 N.m 3.5~5.5 kgf.m, 25.3~39.8 lb-ft
64
Maintenance
OVI071125N 6.Loosen the mounting bolts, then dis-
connect the connector. 7.Remove the side seat.
OBH072103N 2.Remove the rear package tray trim 1.Remove the rear door scuff trim.
OVI071132N 2.Loosen the mounting screw, then
remove the rear wheel house trim.
7 65
Maintenance
OBH072104N 3.Remove the cap, then loosen the
mounting screw.
4.Remove the rear pillar trim.
OVI071134N 5.Push the hook, remove the rear seat
belt cover.
OVI071135N 6.Remove the rear seat belt lower
anchor.
Tightening torque : 39.2~53.9 N.m 4.0~5.5 kgf.m 28.9~39.8 lb-ft
66
Maintenance
OVI071136N 7.Loosen the mounting screws, then
remove the package tray trim.
OVI071137N
OBH078036
3.Replace the high mounted stop
light
1.Remove the high mounted stop lamp
after removing screws.
2.Install a new light.
G220500AEN License plate light bulb replace- ment 1. Loosen the lens retaining screws with
a philips head screwdriver.
4.Installation Installation is the reverse of removal.
2. Remove the lens. 3. Remove the bulb by pulling it straight
out.
4. Install a new bulb. 5. Reinstall the lens securely with the
lens retaining screws.
7 67
Maintenance
Luggage lamp (if equipped)
Sunvisor lamp
OBH048086
OBH078046
G220900ABH Door courtesy lamp bulb replace- ment If the light is not operating, have the vehi- cle checked by an authorized HYUNDAI dealer.
Glove box lamp
OEN076044
68
OBH078037
G220600BBH Interior light bulb replacement 1. Using a flat-blade screwdriver, gently pry the lens from the interior light housing.
2. Remove the bulb by pulling it straight
out.
WARNING
Prior to working on the Interior Lights, ensure that the “OFF” but- ton is depressed to avoid burning your fingers or receiving an electric shock.
3. Install a new bulb in the socket. 4. Align the lens tabs with the interior light housing notches and snap the lens into place.
5. If the map lamp and room lamp are not operating, have the vehicle checked by an authorized HYUNDAI dealer.
CAUTION
Use care not to dirty or damage lens,lens tab,and plastic housings.
APPEARANCE CARE Exterior care G230101AUN Exterior general caution It is very important to follow the label directions when using any chemical cleaner or polish. Read all warning and caution statements that appear on the label.
Maintenance
G230102ABH Finish maintenance Washing To help protect your vehicle’s finish from rust and deterioration, wash it thoroughly and frequently at least once a month with lukewarm or cold water. If you use your vehicle for off-road driv- ing, you should wash it after each off- road trip. Pay special attention to the removal of any accumulation of salt, dirt, mud, and other foreign materials. Make sure the drain holes in the lower edges of the doors and rocker panels are kept clear and clean. Insects, tar, tree sap, bird droppings, industrial pollution and similar deposits can damage your vehicle’s finish if not removed immediately. Even prompt washing with plain water may not completely remove all these deposits. A mild soap, safe for use on painted surfaces, may be used. After washing, rinse the vehicle thor- oughly with lukewarm or cold water. Do not allow soap to dry on the finish.
CAUTION
(cid:129) Do not use strong soap,chemical detergents or hot water, and do not wash the vehicle in direct sunlight or when the body of the vehicle is warm.
(cid:129) Be careful when washing the side windows of your vehicle. Especially, with high-pressure water,water may leak through the windows and wet the interior.
(cid:129) To prevent damage to the plastic parts and lamps, do not clean with chemical solvents or strong detergents.
WARNING - Wet brakes
After washing the vehicle, test the brakes while driving slowly to see if they have been affected by water. If braking performance is impaired, dry the brakes by applying them lightly while maintaining a slow for- ward speed.
7 69
G230103AUN Finish damage repair Deep scratches or stone chips in the painted surface must be repaired promptly. Exposed metal will quickly rust and may develop into a major repair expense.
✽✽ NOTICE If your vehicle is damaged and requires any metal repair or replacement, be sure the body shop applies anti-corrosion materials to the parts repaired or replaced.
Maintenance
OJB037800
CAUTION
(cid:129) Water washing in the engine com- partment including high pressure water washing is not recommend- ed. It may cause the failure of electrical circuits or engine and related part located in the engine compartment.
(cid:129) Never allow water or other liquids to come in contact with electri- cal/electronic components and the air duct inside the vehicle as this may damage them.
70
Waxing A good coat of wax is a barrier between your paint and contaminate. Keeping a good coat of wax on your vehicle will help protect it. Wax the vehicle when water will no longer bead on the paint. Always wash and dry the vehicle before waxing. Use a good quality liquid or paste wax, and follow the manufacturer’s instructions. Wax all metal trim to protect it and to maintain its luster. Removing oil, tar, and similar materials with a spot remover will usually strip the wax from the finish. Be sure to re-wax these areas even if the rest of the vehicle does not yet need waxing.
CAUTION
(cid:129) Wiping dust or dirt off the body with a dry cloth will scratch the finish.
(cid:129) Do not use steel wool, abrasive cleaners, or strong detergents containing highly alkaline or caustic agents on chrome-plated or anodized aluminum parts.This may result in damage to the pro- tective coating and cause discol- oration or paint deterioration.
G230104AUN Bright-metal maintenance (cid:129) To remove road tar and insects, use a tar remover, not a scraper or other sharp object.
(cid:129) To protect the surfaces of bright-metal parts from corrosion, apply a coating of wax or chrome preservative and rub to a high luster.
(cid:129) During winter weather or in coastal areas, cover the bright metal parts with a heavier coating of wax or preserva- tive. If necessary, coat the parts with non-corrosive petroleum jelly or other protective compound.
G230105AUN Underbody maintenance Corrosive materials used for ice and snow removal and dust control may col- lect on the underbody. If these materials are not removed, accelerated rusting can occur on underbody parts such as the fuel lines, frame, floor pan and exhaust system, even though they have been treated with rust protection. Thoroughly flush the vehicle underbody and wheel openings with lukewarm or cold water once a month, after off-road driving and at the end of each winter. Pay special attention to these areas because it is difficult to see all the mud and dirt. It will do more harm than good to wet down the road grime without removing it. The lower edges of doors, rocker panels, and frame members have drain holes that should not be allowed to clog with dirt; trapped water in these areas can cause rusting.
WARNING
After washing the vehicle, test the brakes while driving slowly to see if they have been affected by water. If braking performance is impaired, dry the brakes by applying them lightly while maintaining a slow for- ward speed.
Maintenance
G230106AUN Aluminum or chrome wheel mainte- nance The aluminum or chrome wheels are coated with a clear protective finish. (cid:129) Do not use any abrasive cleaner, pol- ishing compound, solvent, or wire brushes on aluminum or chrome wheels. They may scratch or damage the finish.
(cid:129) Clean the wheel when it has cooled. (cid:129) Use only a mild soap or neutral deter- gent, and rinse thoroughly with water. Also, be sure to clean the wheels after driving on salted roads. This helps pre- vent corrosion.
(cid:129) Avoid washing the wheels with high-
speed car wash brushes.
(cid:129) Do not use any alkaline or acid deter- gent. It may damage and corrode the aluminum or chrome wheels coated with a clear protective finish.
7 71
Maintenance
G230107AUN Corrosion protection Protecting your vehicle from corrosion By using the most advanced design and construction practices to combat corro- sion, we produces cars of the highest qual- ity. However, this is only part of the job. To achieve the long-term corrosion resistance your vehicle can deliver, the owner's coop- eration and assistance is also required.
Common causes of corrosion The most common causes of corrosion on your car are: (cid:129) Road salt, dirt and moisture that is allowed to accumulate underneath the car.
(cid:129) Removal of paint or protective coatings by stones, gravel, abrasion or minor scrapes and dents which leave unpro- tected metal exposed to corrosion.
High-corrosion areas If you live in an area where your car is regularly exposed to corrosive materials, corrosion protection is particularly impor- tant. Some of the common causes of accelerated corrosion are road salts, dust control chemicals, ocean air and industrial pollution.
72
Moisture breeds corrosion Moisture creates the conditions in which corrosion is most likely to occur. For example, corrosion is accelerated by high humidity, particularly when tempera- tures are just above freezing. In such conditions, the corrosive material is kept in contact with the car surfaces by mois- ture that is slow to evaporate. Mud is particularly corrosive because it is slow to dry and holds moisture in contact with the vehicle. Although the mud appears to be dry, it can still retain the moisture and promote corrosion. High temperatures can also accelerate corrosion of parts that are not properly ventilated so the moisture can be dis- persed. For all these reasons, it is par- ticularly important to keep your car clean and free of mud or accumulations of other materials. This applies not only to the visible surfaces but particularly to the underside of the car.
To help prevent corrosion You can help prevent corrosion from get- ting started by observing the following:
Keep your car clean The best way to prevent corrosion is to keep your car clean and free of corrosive materials. Attention to the underside of the car is particularly important.
(cid:129) If you live in a high-corrosion area — where road salts are used, near the ocean, areas with industrial pollution, acid rain, etc.—, you should take extra care to prevent corrosion. In winter, hose off the underside of your car at least once a month and be sure to clean the underside thoroughly when winter is over.
(cid:129) When cleaning underneath the car, give particular attention to the compo- nents under the fenders and other areas that are hidden from view. Do a thorough job; just dampening the accu- mulated mud rather than washing it away will accelerate corrosion rather than prevent it. Water under high pres- sure and steam are particularly effec- tive in removing accumulated mud and corrosive materials.
(cid:129) When cleaning lower door panels, rocker panels and frame members, be sure that drain holes are kept open so that moisture can escape and not be trapped inside to accelerate corrosion.
Keep your garage dry Don't park your car in a damp, poorly ventilated garage. This creates a favor- able environment for corrosion. This is particularly true if you wash your car in the garage or drive it into the garage when it is still wet or covered with snow, ice or mud. Even a heated garage can contribute to corrosion unless it is well ventilated so moisture is dispersed.
Keep paint and trim in good condition Scratches or chips in the finish should be covered with "touch-up" paint as soon as possible to reduce the possibility of cor- rosion. If bare metal is showing through, the attention of a qualified body and paint shop is recommended.
Bird droppings : Bird droppings are high- ly corrosive and may damage painted surfaces in just a few hours. Always remove bird droppings as soon as possi- ble.
Maintenance
Don't neglect the interior Moisture can collect under the floor mats and carpeting to cause corrosion. Check under the mats periodically to be sure the carpeting is dry. Use particular care if you carry fertilizers, cleaning materials or chemicals in the car. These should be carried only in proper containers and any spills or leaks should be cleaned up, flushed with clean water and thoroughly dried.
Interior care G230201AUN Interior general precautions Prevent chemicals such as perfume, cos- metic oil, sun cream, hand cleaner, and air freshener from contacting the interior parts because they may cause damage or discoloration. If they do contact the interior parts, wipe them off immediately. See the instructions for the proper way to clean vinyl.
CAUTION
(cid:129) Never allow water or other liquids to come in contact with electri- cal/electronic components inside the vehicle as this may damage them.
(cid:129) When cleaning leather products (steering wheel, seats etc.), use neutral detergents or low alcohol content solutions.If you use high alcohol content solutions or acid/alkaline detergents,the color of the leather may fade or the sur- face may get stripped off.
7 73
G230203AUN Cleaning the lap/shoulder belt web- bing Clean the belt webbing with any mild soap solution recommended for cleaning upholstery or carpet. Follow the instruc- tions provided with the soap. Do not bleach or re-dye the webbing because this may weaken it.
G230204AUN Cleaning the interior window glass If the interior glass surfaces of the vehi- cle become fogged (that is, covered with an oily, greasy or waxy film), they should be cleaned with glass cleaner. Follow the directions on the glass cleaner container.
CAUTION
Do not scrape or scratch the inside of the rear window.This may result in damage to the rear window defroster grid.
Maintenance
G230202AUN Cleaning the upholstery and interior trim Vinyl Remove dust and loose dirt from vinyl with a whisk broom or vacuum cleaner. Clean vinyl surfaces with a vinyl cleaner.
Fabric Remove dust and loose dirt from fabric with a whisk broom or vacuum cleaner. Clean with a mild soap solution recom- mended for upholstery or carpets. Remove fresh spots immediately with a fabric spot cleaner. If fresh spots do not receive immediate attention, the fabric can be stained and its color can be affected. Also, its fire-resistant properties can be reduced if the material is not properly maintained.
CAUTION
Using anything but recommended cleaners and procedures may affect the fabric’s appearance and fire- resistant properties.
74
for
the
Caution Inspection and Maintenance Test (With Electronic Stability Control (ESC) system) (cid:129) To prevent the vehicle from misfir- ing during dynamometer testing, turn the Electronic Stability Control (ESC) system off by pressing the ESC switch.
(cid:129) After dynamometer testing is com- pleted, turn the ESC system back on by pressing the ESC switch again.
EMISSION CONTROL SYSTEM G270000AEN-EU The emission control system of your vehicle is covered by a written limited warranty. Please see the warranty infor- mation contained the Owner’s Handbook & Warranty Information book- let in your vehicle. Your vehicle is equipped with an emis- sion control system to meet all applicable emission regulations. There are three emission control sys- tems, as follows.
in
(1) Crankcase emission control system (2) Evaporative emission control system (3) Exhaust emission control system
In order to assure the proper function of the emission control systems, it is rec- ommended that you have your car inspected and maintained by an author- ized HYUNDAI dealer in accordance with the maintenance schedule in this manu- al.
Maintenance
G270100AUN 1. Crankcase emission control
system
The positive crankcase ventilation sys- tem is employed to prevent air pollution caused by blow-by gases being emitted from the crankcase. This system supplies fresh filtered air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, which then pass through the PCV valve into the induction system.
G270200AUN 2. Evaporative emission control
(including ORVR: Onboard Refueling Vapor Recovery) system
The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmos- phere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, preventing the escape of fuel vapors into the atmosphere.)
7 75
Maintenance
G270201AUN Canister Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the engine intake manifold through the purge control sole- noid valve.
G270202AUN Purge Control Solenoid Valve (PCSV) The purge control solenoid valve is con- trolled by the Engine Control Module (ECM); when the engine coolant temper- ature is low during idling, the PCSV clos- es so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.
G270300AUN 3. Exhaust emission control
system
The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle performance.
G270301AUN Vehicle modifications (cid:129) This vehicle should not be modified. Modification of your vehicle could affect its performance, safety or dura- bility and may even violate governmen- tal safety and emissions regulations. In addition, damage or performance problems resulting from any modification may not be covered under warranty.
(cid:129) Use of unauthorized electric devices may cause: Abnormal vehicle operation, Wire damage, Battery discharge, Fire. Be careful not to damage your vehicle by use of unauthorized electric devices.
G270302AUN-EU Engine exhaust gas precautions (carbon monoxide) (cid:129) Carbon monoxide can be present with other exhaust fumes. Therefore, if you smell exhaust fumes of any kind inside your vehicle, have it inspected and repaired immediately. If you ever sus- pect exhaust fumes are coming into your vehicle, drive it only with all the windows fully open. Have your vehicle checked and repaired immediately.
WARNING - Exhaust
Engine exhaust gases contain car- bon monoxide (CO). Though color- less and odorless, it is dangerous and could be lethal if inhaled. Follow the instructions on this page to avoid CO poisoning.
CALIFORNIA PROPOSI- TION 65 WARNING
Engine exhaust and a wide variety of automobile components and parts, including components found in the interior furnishings in a vehi- cle, contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, cer- tain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
76
(cid:129) Do not operate the engine in confined or closed areas (such as garages) any more than what is necessary to move the vehicle in or out of the area.
(cid:129) When the vehicle is stopped in an open area for more than a short time with the engine running, adjust the ventilation system (as needed) to draw outside air into the vehicle.
(cid:129) Never sit in a parked or stopped vehi- cle for any extended time with the engine running.
(cid:129) When the engine stalls or fails to start, excessive attempts to restart the engine may cause damage to the emission control system.
G270303AEN Operating precautions for catalytic converters (if equipped)
WARNING - Fire
(cid:129) A hot exhaust system can ignite flammable items under your vehi- cle. Do not park, idle, or drive the vehicle over or near flammable objects, such as grass, vegeta- tion, paper, leaves, etc.
(cid:129) The exhaust system and catalytic system are very hot while the engine is running or immediately after the engine is turned off. Keep away from the exhaust sys- tem and catalytic, you may get burned. Also, do not remove the heat sink around the exhaust system, do not seal the bottom of the vehicle or do not coat the vehicle for cor- rosion control. It may present a fire risk under certain conditions.
Maintenance
Your vehicle is equipped with a catalytic converter emission control device. Therefore, the following precautions must be observed: (cid:129) Use only UNLEADED FUEL for gaso-
line engines.
(cid:129) Do not operate the vehicle when there are signs of engine malfunction, such as misfire or a noticeable loss of per- formance.
(cid:129) Do not misuse or abuse the engine. Examples of misuse are coasting with the ignition off and descending steep grades in gear with the ignition off.
(cid:129) Do not operate the engine at high idle speed for extended periods (5 minutes or more).
(cid:129) Do not modify or tamper with any part of the engine or emission control sys- tem. All inspections and adjustments must be made by an authorized HYUNDAI dealer.
(cid:129) Avoid driving with a very low fuel level. If you run out of gasoline, it could cause the engine to misfire and result in exces- sive loading of the catalytic converter.
Failure to observe these precautions could result in damage to the catalytic converter and to your vehicle. Additionally, such actions could void your warranties.
7 77
Maintenance
CALIFORNIA PERCHLORATE NOTICE G280000AEN Perchlorate Material-special handling may apply, See www.dtsc.ca.gov/haz- ardouswaste/perchlorate.
Notice to California Vehicle Dismantlers: Perchlorate containing materials, such as air bag inflators, seatbelt pretensioners and keyless remote entry batteries, must be disposed of according to Title 22
California Code of Regulations Section 67384.10 (a).78
Dimensions / 8-2
Bulb wattage / 8-2
Tires and wheels / 8-3
Recommended lubricants and capacities / 8-4
Vehicle identification number (VIN) / 8-7
Vehicle certification label / 8-7
Tire specification and pressure label / 8-8
Engine number / 8-8
Consumer information / 8-9
Reporting safety defects / 8-10
Binding arbitration / 8-10Specifications, Consumer information, Reporting safety defects
Specifications, Consumer information, Reporting safety defects
DIMENSIONS I010000ABH
Item
Overall length Overall width Overall height Front tread Rear tread Wheelbase
in (mm)
196.3 (4985) 74.4 (1890)
58.1 (1475)*1 / 58.2 (1480)*2
63.8 (1620)*1 / 63.1 (1604)*2
64.4 (1636)*1 / 63.8 (1621)*2115.6 (2935)
*1 : with P215/60R17 tire or with P225/55R17 tire *2 : with P235/50R18 tire or with P235/45R19 tire
28
BULB WATTAGE I030000ABH
Light Bulb
Headlights (Low) Headlights (High) Front turn signal lights Position lights Side repeater lights Front side marker lights Front fog lights* Stop and tail lights Tail light Rear turn signal lights Back-up lights Rear side marker lights High mounted stop light License plate lights Map lamps Room lamps Luggage lamp Glove box lamp Vanity mirror lamps Door courtesy lamps*
* : If equipped
Wattage
55 or 35 (HID)
55
24
LED LED LED 35
LED LED 21
16
LED LEDLED LED
Specifications, Consumer information, Reporting safety defects
TIRES AND WHEELS I020000AEN-EU
Item
Tire size
Wheel size
Full size tire
Compact spare tire
P215/60R17
P225/55R17
P235/50R18
P235/45R19T135/90D17
6.5J×17
7.5J×18
8.0J×19
