provided.
(cid:129) Before emergency towing, check that
the hook is not broken or damaged.
(cid:129) Fasten the towing cable or chain
securely to the hook.
(cid:129) Do not jerk the hook. Apply steady and
even force.
(cid:129) To avoid damaging the hook, do not pull from the side or at a vertical angle. Always pull straight ahead.
WARNING
Use extreme caution when towing the vehicle. (cid:129) Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing hook and tow- ing cable or chain. The hook and towing cable or chain may break and cause serious injury or dam- age.
(cid:129) If the disabled vehicle cannot be moved, do not forcibly continue the towing. Contact an authorized Hyundai dealer or a commercial tow truck service for assistance. (cid:129) Tow the vehicle as straight ahead
as possible.
(cid:129) Keep away from the vehicle dur-
ing towing.
28
Emergency towing precautions (cid:129) Turn the ignition switch to ACC so the
steering wheel isn’t locked.
(cid:129) Place the transaxle shift lever in N
(Neutral).
(cid:129) Release the parking bake. (cid:129) Press the brake pedal with more force than normal since you will have reduced brake performance.
(cid:129) More steering effort will be required because the power steering system will be disabled.
(cid:129) If you are driving down a long hill, the brakes may overheat and brake per- formance will be reduced. Stop often and let the brakes cool off.
OUN046024
(cid:129) Use a towing strap less than 16 feet (5
m) long. Attach a white or red cloth
(about 12 inches (30 cm) wide) in the
middle of the strap for easy visibility.
(cid:129) Drive carefully so that the towing strap
is not loosened during towing.
What to do in an emergency
CAUTION - Automatic transaxle
(cid:129) If the car is being towed with all four wheels on the ground,it can be towed only from the front.Be sure that the transaxle is in neu- tral. Be sure the steering is unlocked by placing the ignition switch in the ACC position. A driver must be in the towed vehi- cle to operate the steering and brakes.
(cid:129) To avoid serious damage to the
automatic transaxle, limit the
vehicle speed to 10 mph (15 km/h)
and drive less than 1 mile (1.5
km) when towing.
(cid:129) Before towing, check the auto- matic transaxle fluid leak under your vehicle. If the automatic transaxle fluid is leaking, a flatbed equipment or towing dolly must be used.
6 29
Engine compartment / 7-2
Maintenance services / 7-3
Owner maintenance / 7-4
Scheduled maintenance service / 7-6
Explanation of scheduled maintenance items / 7-18
Engine oil / 7-21
Engine coolant / 7-23
Brake/clutch fluid / 7-25
Washer fluid / 7-26
Parking brake / 7-26
Air cleaner / 7-27
Climate control air filter / 7-28
Wiper blades / 7-30
Battery / 7-33
Tires and wheels / 7-36
Fuses / 7-49
Light bulbs / 7-58
Maintenance
Appearance care / 7-67
Emission control system / 7-73
California perchlorate notice / 7-76
Maintenance
ENGINE COMPARTMENT
1. Engine oil filler cap 2. Engine oil dipstick 3. Brake/clutch fluid reservoir 4. Positive battery terminal 5. Negative battery terminal 6. Fuse box 7. Air cleaner 8. Radiator cap 9. Engine coolant reservoir 10. Windshield washer fluid reservoir * : if equipped
* The actual engine room in the vehicle may differ from the illustration.
OMD070047N
27
MAINTENANCE SERVICES You should exercise the utmost care to prevent damage to your vehicle and injury to yourself whenever performing any maintenance or inspection proce- dures. Should you have any doubts concerning the inspection or servicing of your vehi- cle, we strongly recommend that you have an authorized HYUNDAI dealer perform this work. An authorized HYUNDAI dealer has fac- tory-trained technicians and genuine HYUNDAI parts to service your vehicle properly. For expert advice and quality service, see an authorized HYUNDAI dealer. Inadequate, incomplete or insufficient servicing may result in operational prob- lems with your vehicle that could lead to vehicle damage, an accident, or person- al injury.
Owner’s responsibility
✽✽ NOTICE Maintenance Service and Record Retention are the owner's responsibility.
You should retain documents that show proper maintenance has been performed on your vehicle in accordance with the scheduled maintenance service charts shown on the following pages. You need this information to establish your compli- ance with the servicing and maintenance requirements of your vehicle warranties. Detailed warranty information is provided in your Owner’s Handbook & Warranty Information booklet. Repairs and adjustments required as a result of improper maintenance or a lack of required maintenance are not covered. We recommend you have your vehicle maintained and repaired by an author- ized HYUNDAI dealer. An authorized HYUNDAI dealer meets HYUNDAI’s high service quality standards and receives technical support from HYUNDAI in order to provide you with a high level of service satisfaction.
Maintenance
Owner maintenance precautions Improper or incomplete service may result in problems. This section gives instructions only for the maintenance items that are easy to perform. As explained earlier in this section, sev- eral procedures can be done only by an authorized HYUNDAI dealer with special tools.
✽✽ NOTICE Improper owner maintenance during the warranty period may affect warran- ty coverage. For details, read the sepa- rate Owner’s Handbook & Warranty Information booklet provided with the vehicle. If you're unsure about any serv- icing or maintenance procedure, have it done by an authorized HYUNDAI deal- er.
7 3
OWNER MAINTENANCE The following lists are vehicle checks and inspections that should be performed by the owner or an authorized HYUNDAI dealer at the frequencies indicated to help ensure safe, dependable operation of your vehicle. Any adverse conditions should be brought to the attention of your dealer as soon as possible. These Owner Maintenance Checks are generally not covered by warranties and you may be charged for labor, parts and lubricants used.
Owner maintenance schedule When you stop for fuel: (cid:129) Check the engine oil level. (cid:129) Check coolant level in coolant reser-
voir.
(cid:129) Check the windshield washer fluid
level.
(cid:129) Look for low or under-inflated tires.
WARNING
Be careful when checking your engine coolant level when the engine is hot. Scalding hot coolant and steam may blow out under pressure. This could cause burns or other serious injury.
Maintenance
WARNING - Maintenance
work
(cid:129) Performing maintenance work on a vehicle can be dangerous. You can be seriously injured while performing some maintenance procedures. If you lack sufficient knowledge and experience or the proper tools and equipment to do the work, have it done by an authorized HYUNDAI dealer.
(cid:129) Working under the hood with the engine running is dangerous. It becomes even more dangerous when you wear jewelry or loose clothing. These can become entangled in moving parts and result in injury. Therefore, if you must run the engine while work- ing under the hood, make certain that you remove all jewelry (espe- cially rings, bracelets, watches, and necklaces) and all neckties, scarves, and similar loose cloth- ing before getting near the engine or cooling fans.
47
While operating your vehicle: (cid:129) Note any changes in the sound of the exhaust or any smell of exhaust fumes in the vehicle.
(cid:129) Check for vibrations in the steering wheel. Notice any increased steering effort or looseness in the steering wheel, or change in its straight-ahead position.
(cid:129) Notice if your vehicle constantly turns slightly or “pulls” to one side when trav- eling on smooth, level road.
(cid:129) When stopping, listen and check for unusual sounds, pulling to one side, increased brake pedal travel or “hard- to-push” brake pedal.
(cid:129) If any slipping or changes in the oper- ation of your transaxle occurs, check the transaxle fluid level.
(cid:129) Check automatic transaxle P (Park)
function.
(cid:129) Check parking brake. (cid:129) Check for fluid leaks under your vehicle (water dripping from the air condition- ing system during or after use is nor- mal).
At least monthly: (cid:129) Check coolant level in the engine
coolant reservoir.
(cid:129) Check the operation of all exterior lights, including the stoplights, turn sig- nals and hazard warning flashers.
(cid:129) Check the inflation pressures of all
tires including the spare.
At least twice a year (i.e.,every Spring and Fall): (cid:129) Check radiator, heater and air condi-
tioning hoses for leaks or damage.
(cid:129) Check windshield washer spray and wiper operation. Clean wiper blades with clean cloth dampened with wash- er fluid.
(cid:129) Check headlight alignment. (cid:129) Check muffler, exhaust pipes, shields
and clamps.
(cid:129) Check the lap/shoulder belts for wear
and function.
(cid:129) Check for worn tires and loose wheel
lug nuts.
Maintenance
At least once a year: (cid:129) Clean body and door drain holes. (cid:129) Lubricate door hinges and checks, and
hood hinges.
(cid:129) Lubricate door and hood locks and
latches.
(cid:129) Lubricate door rubber weatherstrips. (cid:129) Check the air conditioning system. (cid:129) Inspect and
lubricate automatic
transaxle linkage and controls.
(cid:129) Clean battery and terminals. (cid:129) Check the brake fluid level.
7 5
Maintenance
SCHEDULED MAINTENANCE SERVICE Follow Normal Maintenance Schedule if the vehicle is usually operated where none of the following conditions apply. If any of the following conditions apply, fol- low Maintenance Under Severe Usage Conditions. (cid:129) Repeated short distance driving. (cid:129) Driving in dusty conditions or sandy
If your vehicle is operated under the above conditions, you should inspect, replace or refill more frequently than the following Normal Maintenance Schedule. After 120 months or 150,000 miles (240,000 km) continue to follow the pre- scribed maintenance intervals.
areas.
(cid:129) Extensive use of brakes. (cid:129) Driving in areas where salt or other
corrosive materials are being used.
(cid:129) Driving on rough or muddy roads. (cid:129) Driving in mountainous areas. (cid:129) Extended periods of idling or low
speed operation.
(cid:129) Driving for a prolonged period in cold temperatures and/or extremely humid climates.
(cid:129) More than 50% driving in heavy city traffic during hot weather above 90°F (32°C).
67
Maintenance
NORMAL MAINTENANCE SCHEDULE The following maintenance services must be performed to ensure good emission control and performance. Keep receipts for all vehicle emission services to protect your warranty. Where both mileage and time are shown, the frequency of service is deter- mined by whichever occurs first.
7,500 miles (12,000 km) or 6 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(7,500 miles (12,000 km) or 12 months)
15,000 miles (24,000 km) or 12 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped)
(Continued)
(Continued) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter
(15,000 miles (24,000 km) or 24 months)
22,500 miles (36,000 km) or 18 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(22,500 miles (36,000 km) or 36 months)
7 7
Maintenance
NORMAL MAINTENANCE SCHEDULE (CONT.)
30,000 miles (48,000 km) or 24 months
37,500 miles (60,000 km) or 30 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect manual transaxle fluid (if equipped) ❑ Replace engine oil and filter
(37,500 miles (60,000 km) or 60 months)
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but peri- odic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restric- tion, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect brake/clutch (if equipped) fluid
❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections
❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect parking brake
❑ Inspect vapor hose and fuel filler cap
❑ Replace climate control air filter (for evaporator and blower unit)
❑ Replace air cleaner filter
❑ Replace engine oil and filter
(30,000 miles (48,000 km) or 48 months)
87
NORMAL MAINTENANCE SCHEDULE (CONT.)
45,000 miles (72,000 km) or 36 months
52,500 miles (84,000 km) or 42 months
Maintenance
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(52,500 miles (84,000 km) or 84 months)
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter
(45,000 miles (72,000 km) or 72 months)
7 9
Maintenance
NORMAL MAINTENANCE SCHEDULE (CONT.)
60,000 miles (96,000 km) or 48 months
67,500 miles (108,000 km) or 54 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(67,500 miles (108,000 km) or 108 months)
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect brake/clutch (if equipped) fluid
❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections
❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect parking brake
❑ Inspect vapor hose and fuel filler cap
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter
(60,000 miles (96,000 km) or 96 months)
10
NORMAL MAINTENANCE SCHEDULE (CONT.)
75,000 miles (120,000 km) or 60 months
82,500 miles (132,000 km) or 66 months
Maintenance
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(82,500 miles (132,000 km) or 132 months)
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect manual transaxle fluid (if equipped)
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter
(75,000 miles (120,000 km) or 120 months)
7 11
Maintenance
NORMAL MAINTENANCE SCHEDULE (CONT.)
90,000 miles (144,000 km) or 72 months
97,500 miles (156,000 km) or 78 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(97,500 miles (156,000 km) or 156 months)
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an author- ized HYUNDAI dealer for details.
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect brake/clutch (if equipped) fluid
❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections
❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect parking brake
❑ Inspect vapor hose and fuel filler cap
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter
(90,000 miles (144,000 km) or 144 months)
12
NORMAL MAINTENANCE SCHEDULE (CONT.)
105,000 miles (168,000 km) or 84 months
112,500 miles (180,000 km) or 90 months
Maintenance
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect manual transaxle fluid (if equipped) ❑ Replace engine oil and filter
(112,500 miles (180,000 km) or 180 months)
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace spark plugs (iridium coated) ❑ Replace engine oil and filter
(105,000 miles (168,000 km) or 168 months)
7 13
Maintenance
NORMAL MAINTENANCE SCHEDULE (CONT.)
120,000 miles (192,000 km) or 96 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect brake/clutch (if equipped) fluid
❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections
❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect parking brake
❑ Inspect vapor hose and fuel filler cap
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
(Continued)
14
(Continued) ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter
(120,000 miles (192,000 km) or 192 months)
❑ Replace coolant (First, 120,000 miles (192,000 km) or 120 months
after every 30,000 miles (48,000 km) or 24 months)
127,500 miles (204,000 km) or 102 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(127,500 miles (204,000 km) or 204 months)
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
NORMAL MAINTENANCE SCHEDULE (CONT.)
135,000 miles (216,000 km) or 108 months
142,500 miles (228,000 km) or 114 months
Maintenance
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter
(142,500 miles (228,000 km) or 228 months)
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter
(135,000 miles (216,000 km) or 216 months)
7 15
Maintenance
NORMAL MAINTENANCE SCHEDULE (CONT.)
150,000 miles (240,000 km) or 120 months
❑ Rotate tire ❑ Inspect battery condition ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect exhaust pipe and muffler ❑ Inspect front brake disc/pads, calipers ❑ Inspect rear brake disc/pads (if equipped) ❑ Inspect rear brake drums/linings (if equipped) ❑ Inspect electronic throttle control ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,
upper arm ball joint
❑ Inspect suspension mounting bolts
❑ Inspect brake/clutch (if equipped) fluid
❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections
❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect parking brake
❑ Inspect vapor hose and fuel filler cap
❑ Inspect manual transaxle fluid (if equipped)
❑ Inspect drive belts *2
(First, 60,000 miles (96,000 km) or 72 months after every 15,000 miles (24,000 km) or 24 months)
(Continued)
16
(Continued) ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter
(150,000 miles (240,000 km) or 240 months)
❑ Replace coolant (First, 120,000 miles (192,000 km) or 120 months
after every 30,000 miles (48,000 km) or 24 months)
No check, No service required
❑ Automatic transaxle fluid (if equipped)
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.
*2 : The drive belt should be replaced when cracks occur or tension is reduced
excessively.
Maintenance
MAINTENANCE UNDER SEVERE USAGE CONDITIONS The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals. R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary
MAINTENANCE ITEM
MAINTENANCE
OPERATION
MAINTENANCE INTERVALS
DRIVING CONDITION
ENGINE OIL AND FILTER
AIR CLEANER FILTER
SPARK PLUGS
AUTOMATIC TRANSAXLE FLUID
MANUAL TRANSAXLE FLUID
FRONT BRAKE DISC/PADS, CALIPERS
REAR BRAKE DISC/PADS
PARKING BRAKE
STEERING GEAR BOX, LINKAGE & BOOTS/ LOWER ARM BALL JOINT, UPPER ARM BALL JOINT
DRIVE SHAFTS AND BOOTS
CLIMATE CONTROL AIR FILTER (FOR EVAPORATOR AND BLOWER UNIT)
EVERY 3,750 MILES (6,000 KM) OR 6 MONTHS
A, B, C, D, E, F, G, H, I, K
MORE FREQUENTLY
MORE FREQUENTLY
EVERY 60,000 MILES (96,000 KM)
EVERY 75,000 MILES (120,000 KM)
MORE FREQUENTLY
MORE FREQUENTLY
MORE FREQUENTLY
C, E
B, H
A, C, E, F, G, I
A, C, E, F, G, I
C, D, G, H
C, D, G, F
C, D, G, H
EVERY 7,500 MILES (12,000 KM) OR 6 MONTHS
C, D, E, F, G, H, I
MORE FREQUENTLY
MORE FREQUENTLY
C, D, E, F, G, H, I
C, E
SEVERE DRIVING CONDITIONS A - Repeatedly driving short distance of less than 5 miles (8 km) in normal
temperature or less than 10 miles (16 km) in freezing temperature
B - Extensive engine idling or low speed driving for long distances C - Driving on rough, dusty, muddy, unpaved, graveled or salt- spread roads D - Driving in areas using salt or other corrosive materials or in very cold
weather
E - Driving in sandy areas
F - Driving in heavy traffic area over 90°F (32°C) G - Driving on uphill, downhill, or mountain road H - Towing a Trailer, or using a camper, or roof rack J - Driving over 106 mph (170 km/h) K - Frequently driving in stop-and-go conditions
- Driving as a patrol car, taxi, other commercial use or vehicle towing
7 17
Maintenance
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS Engine oil and filter The engine oil and filter should be changed at the intervals specified in the maintenance schedule. If the car is being driven in severe conditions, more fre- quent oil and filter changes are required.
Fuel filter A clogged filter can limit the speed at which the vehicle may be driven, damage the emission system and cause multiple issues such as hard starting. If an exces- sive amount of foreign matter accumu- lates in the fuel tank, the filter may require replacement more frequently. After installing a new filter, run the engine for several minutes, and check for leaks at the connections. Fuel filters should be installed by an authorized HYUNDAI dealer.
Fuel lines, fuel hoses and con- nections Check the fuel lines, fuel hoses and con- nections for leakage and damage. Have an authorized HYUNDAI dealer replace any damaged or leaking parts immedi- ately.
Vapor hose and fuel filler cap The vapor hose and fuel filler cap should be inspected at those intervals specified in the maintenance schedule. Make sure that a new vapor hose or fuel filler cap is correctly replaced.
Vacuum crankcase ventilation hoses Inspect the surface of hoses for evidence of heat and/or mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indi- cate deterioration. Particular attention should be paid to examine those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect the hose routing to assure that the hoses do not come in contact with any heat source, sharp edges or moving component which might cause heat dam- age or mechanical wear. Inspect all hose connections, such as clamps and cou- plings, to make sure they are secure, and that no leaks are present. Hoses should be replaced immediately if there is any evidence of deterioration or damage.
Drive belts Inspect all drive belts for evidence of cuts, cracks, excessive wear or oil satu- ration and replace if necessary. Drive belts should be checked periodically for proper tension and adjusted as neces- sary.
18
Air cleaner filter A Genuine HYUNDAI air cleaner filter is recommended when is replaced.
filter
the
Spark plugs Make sure to install new spark plugs of the correct heat range.
Cooling system Check cooling system components, such as radiator, coolant reservoir, hoses and connections for leakage and damage. Replace any damaged parts.
Coolant The coolant should be changed at the intervals specified in the maintenance schedule.
Automatic transaxle fluid (if equipped) Automatic transaxle fluid should not be checked under normal usage conditions. But in severe conditions, the fluid should be changed at an authorized HYUNDAI dealer in accordance to the scheduled maintenance at the beginning of this chapter.
✽✽ NOTICE Automatic transaxle fluid color is basi- cally red. As the vehicle is driven, the automatic transaxle fluid will begin to look darker. It is normal condition and you should not judge the need to replace the fluid based upon the changed color.
CAUTION
The use of a non-specified fluid could result in transaxle malfunc- tion and failure. Use only specified automatic transaxle to “Recommended lubricants and capacities”in section 8.)
(Refer
fluid.
Maintenance
Manual transaxle fluid (if equipped) Inspect fluid according to the maintenance schedule.
the manual
transaxle
Brake hoses and lines Visually check for proper installation, chafing, cracks, deterioration and any leakage. Replace any deteriorated or damaged parts immediately.
Brake/clutch fluid
Check brake fluid level in the brake fluid
reservoir. The level should be between
“MIN” and “MAX” marks on the side of
the reservoir. Use only hydraulic brake
fluid conforming to DOT 3 or DOT 4
specification.
7 19
Steering gear box, linkage & boots/lower arm ball joint With the vehicle stopped and engine off, check for excessive free-play in the steering wheel. Check the linkage for bends or damage. Check the dust boots and ball joints for deterioration, cracks, or damage. Replace any damaged parts.
Drive shafts and boots Check the drive shafts, boots and clamps for cracks, deterioration, or damage. Replace any damaged parts and, if nec- essary, repack the grease.
Air conditioning refrigerant Check the air conditioning lines and con- nections for leakage and damage.
Maintenance
Parking brake Inspect the parking brake system includ- ing the parking brake pedal and cables.
Brake discs, pads, calipers and rotors Check the pads for excessive wear, discs for run out and wear, and calipers for fluid leakage.
Exhaust pipe and muffler Visually inspect the exhaust pipes, muf- fler and hangers for cracks, deterioration, or damage. Start the engine and listen carefully for any exhaust gas leakage. Tighten connections or replace parts as necessary.
Suspension mounting bolts Check the suspension connections for looseness or damage. Retighten to the specified torque.
20
ENGINE OIL
Maintenance
WARNING - Radiator hose Be very careful not to touch the radiator hose when checking or adding the engine oil as it may be hot enough to burn you.
5. Pull the dipstick out again and check the level. The level should be between F and L.
CAUTION
(cid:129) Do not overfill with engine oil.
Engine damage may result.
(cid:129) Do not spill engine oil, when adding or changing engine oil.If you drop the engine oil on the engine room, wipe it off immedi- ately.
OMD070002N
Checking the engine oil level 1. Be sure the vehicle is on level ground. 2. Start the engine and allow it to reach
normal operating temperature.
3. Turn the engine off and wait for a few minutes (about 5 minutes) for the oil to return to the oil pan.
4. Pull the dipstick out, wipe it clean, and
re-insert it fully.
OMD070003N If it is near or at L, add enough oil to bring the level to F. Do not overfill.
Use a funnel to help prevent oil from being spilled on engine components.
Use only the specified engine oil.(Refer to “Recommended lubricants and capaci- ties”in section 8.)
7 21
Maintenance
CALIFORNIA PROPOSI- TION 65 WARNING
Engine oil contains chemicals known to the State of California to cause cancer, birth defects, and reproductive harm. Used engine oil may cause irrita- tion or cancer of the skin if left in contact with the skin for prolonged periods of time. Used engine oil contains chemicals that have caused cancer in laboratory ani- mals. Always protect your skin by washing your hands thoroughly with soap and warm water as soon as possible after handling used oil.
Changing the engine oil and filter Have engine oil and filter changed by an authorized HYUNDAI dealer according to the Maintenance Schedule at the begin- ning of this section.
22
ENGINE COOLANT The high-pressure cooling system has a reservoir filled with year-round antifreeze coolant. The reservoir is filled at the factory. Check the antifreeze protection and coolant level at least once a year, at the beginning of the winter season, and before traveling to a colder climate.
Checking the coolant level
WARNING - Removing radiator cap
(cid:129) Never attempt to remove the radi- ator cap while the engine is oper- ating or hot. Doing so might lead to cooling system and engine damage and could result in seri- ous personal injury from escap- ing hot coolant or steam.
(cid:129) Turn the engine off and wait until it cools down. Use extreme care when removing the radiator cap. Wrap a thick towel around it, and turn it counterclockwise slowly to the first stop. Step back while the pressure is released from the cool- ing system. When you are sure all the pressure has been released, press down on the cap, using a thick towel, and continue turning counterclockwise to remove it.
(Continued)
(Continued) (cid:129) Even if the engine is not operat- ing, do not remove the radiator cap or the drain plug while the engine and radiator are hot. Hot coolant and steam may still blow out under pressure, causing seri- ous injury.
WARNING
The electric motor (cooling fan) is controlled by engine coolant tem- perature, refrigerant pressure and vehicle speed. It may sometimes operate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan so that you are not injured by a rotating fan blades. As the engine coolant temperature decreases, the electric motor will automatically shut off.This is a nor- mal condition.
Maintenance
level should be
OMD070004N Check the condition and connections of all cooling system hoses and heater hoses. Replace any swollen or deterio- rated hoses. The coolant filled between F and L marks on the side of the coolant reservoir when the engine is cool. If the coolant level is low, add enough distilled (deionized) water. Bring the level to F, but do not overfill. If frequent addi- tions are required, see an authorized HYUNDAI dealer for a cooling system inspection.
7 23
Maintenance
Recommended engine coolant (cid:129) When adding coolant, use only deion- ized water or soft water for your vehicle and never mix hard water in the coolant filled at the factory. An improp- er coolant mixture can result in serious malfunction or engine damage.
(cid:129) The engine in your vehicle has aluminum engine parts and must be protected by an ethylene-glycol-based coolant to pre- vent corrosion and freezing.
(cid:129) DO NOT USE alcohol or methanol coolant or mix them with the specified coolant.
(cid:129) Do not use a solution that contains more than 60% antifreeze or less than 35% antifreeze, which would reduce the effectiveness of the solution.
For mixture percentage, refer to the fol- lowing table.
Mixture Percentage (volume)
Antifreeze
Water
35
40
50
60
65
60
50
40
Ambient
Temperature
5°F (-15°C) -13°F (-25°C) -31°F (-35°C) -49°F (-45°C)
24
Changing the coolant Have coolant changed by an authorized HYUNDAI dealer according the Maintenance Schedule at the beginning of this section.
to
CAUTION
Put a thick cloth or fabric around the radiator cap before refilling the coolant in order to prevent the coolant from overflowing into engine parts such as generator.
WARNING - Coolant
(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.
(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.
OMD070005N
WARNING - Radiator cap
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot coolant and steam may blow out under pres- sure causing serious injury.
Maintenance
Use only the specified brake fluid.(Refer to “Recommended lubricants or capaci- ties”in section 8.)
Never mix different types of fluid.
WARNING - Loss of brake/
clutch fluid
In the event the brake system requires frequent additions of fluid, the vehicle should be inspected by an authorized HYUNDAI dealer.
CAUTION
Do not allow brake fluid to contact the vehicle's body paint, as paint damage will result. Brake fluid, which has been exposed to open air for an extended time should never be used as its quality cannot be guaranteed. It should be disposed of properly.Don't put in the wrong kind of fluid.A few drops of miner- al-based oil, such as engine oil, in your brake system can damage brake system parts.
WARNING - Brake/clutch
fluid
When changing and adding brake fluid, handle it carefully. Do not let it come in contact with your eyes. If brake fluid should come in contact with your eyes, immediately flush them with a large quantity of fresh tap water. Have your eyes examined by a doctor as soon as possible.
BRAKE/CLUTCH FLUID
OMD070006N
fluid
Checking the brake/clutch fluid level Check the fluid level in the reservoir peri- odically. The level should be between MAX and MIN marks on the side of the reservoir. Before removing the reservoir cap and adding brake/clutch fluid, clean the area around the reservoir cap thoroughly to prevent brake/clutch fluid contamination. If the level is low, add fluid to the MAX level. The level will fall with accumulated mileage. This is a normal condition asso- ciated with the wear of the brake linings. If the fluid level is excessively low, have the brake system or clutch (if equipped) checked by an authorized HYUNDAI dealer.
7 25
Maintenance
WASHER FLUID
PARKING BRAKE
WARNING - Coolant
(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.
(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.
(cid:129) Windshield washer fluid agents contain some amounts of alcohol and can be flammable under cer- tain circumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reservoir. Damage to the vehicle or occupants could occur.
(cid:129) Windshield washer fluid is poi- sonous to humans and animals. Do not drink and avoid contacting windshield washer fluid. Serious injury or death could occur.
OMD050014
Checking the parking brake Check the stroke of the parking brake by counting the number of “clicks’’ heard while fully applying it from the released position. Also, the parking brake alone should securely hold the vehicle on a fair- ly steep grade. If the stroke is more or less than specified, have the parking brake adjusted by an authorized HYUNDAI dealer.
Stroke : 6~8 “clicks’’ at a force of
44 lbs (20 kg, 196 N).
OMD070007N
Checking the washer fluid level The reservoir is translucent so that you can check the level with a quick visual inspection. Check the fluid level in the washer fluid reservoir and add fluid if necessary. Plain water may be used if washer fluid is not available. However, use washer solvent with antifreeze characteristics in cold cli- mates to prevent freezing.
26
AIR CLEANER
Maintenance
OMD070010
Filter replacement It must be replaced when necessary, and should not be cleaned and reused. You can clean the filter when inspecting the air cleaner element. Clean the filter by using compressed air.
OMD070011
1. Loosen the air cleaner cover attaching
clips and open the cover.
OMD070012
2. Wipe the inside of the air cleaner. 3. Replace the air cleaner filter. 4. Lock the cover with the cover attaching
clips.
7 27
CLIMATE CONTROL AIR FILTER Filter inspection The climate control air filter should be replaced according to the Maintenance Schedule. If the vehicle is operated in severely air-polluted cities or on dusty rough roads for a long period, it should be frequently and replaced earlier. When you replace the climate control air filter, replace it per- forming the following procedure, and be careful to avoid damaging other compo- nents.
inspected more
OMD070013
Filter replacement 1. With the glove box open, remove the stoppers by turning them counter- clockwise on both sides.
Maintenance
Replace the filter according to the Maintenance Schedule. If the vehicle is operated in extremely dusty or sandy areas, replace the ele- ment more often than the usual recom- mended to “Maintenance under severe usage condi- tions”in this section.)
intervals.
(Refer
CAUTION
(cid:129) Do not drive with the air cleaner removed;this will result in exces- sive engine wear.
(cid:129) When removing the air cleaner fil- ter, be careful that dust or dirt does not enter the air intake, or damage may result.
(cid:129) Use a HYUNDAI genuine part.Use of non-genuine parts could dam- age the air flow sensor and engine.
28
Maintenance
2. Remove the support strap (1).
OMD070014
OMD070015
3. Remove the climate control air filter
cover (2) while pressing the lock (1) on
the right of the cover.
OVG079016
4. Replace the climate control air filter. 5. Reassemble in the reverse order of
disassembly.
✽✽ NOTICE When replacing the climate control air filter install it properly. Otherwise, the system may produce noise and the effec- tiveness of the filter may be reduced.
7 29
Maintenance
WIPER BLADES
1JBA5122
Blade inspection ✽✽ NOTICE Commercial hot waxes applied by auto- matic car washes have been known to make the windshield difficult to clean.
Contamination of either the windshield or the wiper blades with foreign matter can reduce the effectiveness of the wind- shield wipers. Common sources of con- tamination are insects, tree sap, and hot wax treatments used by some commer- cial car washes. If the blades are not wip- ing properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.
Blade replacement When the wipers no longer clean ade- quately, the blades may be worn or cracked, and require replacement.
CAUTION
To prevent damage to the wiper arms or other components, do not attempt to move the wipers manual- ly.
CAUTION
To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.
CAUTION
The use of a non-specified wiper blade could result in wiper malfunc- tion and failure.
30
■ Type A
■ Type B
Maintenance
1LDA5023
Front windshield wiper blade Type A 1. Raise the wiper arm and turn the wiper blade assembly to expose the plastic locking clip.
CAUTION
Do not allow the wiper arm to fall against the windshield,since it may chip or crack the windshield.
1JBA7037
1JBA7038
2. Compress the clip and slide the blade
assembly downward.
3. Lift it off the arm. 4. Install the blade assembly in the
reverse order of removal.
OHM078059
Front windshield wiper blade Type B 1. Raise the wiper arm.
CAUTION
Do not allow the wiper arm to fall against the windshield,since it may chip or crack the windshield.
7 31
Maintenance
OYF079061
2. Lift up the wiper blade clip. Then pull
down the blade assembly and remove
it.
OYF079062
3. Install the new blade assembly in the
reverse order of removal.
32
BATTERY
OMD070016
For best battery service (cid:129) Keep the battery securely mounted. (cid:129) Keep the battery top clean and dry. (cid:129) Keep the terminals and connections clean, tight, and coated with petroleum jelly or terminal grease.
(cid:129) Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda.
(cid:129) If the vehicle is not going to be used for an extended time, disconnect the bat- tery cables.
WARNING - Battery dangers
Always read the following instructions carefully when handling a battery. Keep lighted cigarettes and all other flames or sparks away from the battery. Hydrogen, a highly com- bustible gas, is always present in battery cells and may explode if ignited. Keep batteries out of the reach of children because batteries contain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, clothing or paint finish. If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention.
(Continued)
Maintenance
(Continued)
If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensa- tion, get medical attention immediately. Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space. An inappropriately disposed battery can be harmful to the environment and human health. Dispose the battery according to your local law(s) or regulation.
Pb
(cid:129) When lifting a plastic-cased bat- tery, excessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners. (cid:129) Never attempt to recharge the battery when the battery cables are connected.
(Continued)
7 33
Battery recharging Your vehicle has a maintenance-free, calcium-based battery. If the battery becomes discharged in a short time (because, for example the headlights or interior lights were left on while vehicle was not in use) jump start the vehicle from another battery and run the engine at least 20 minutes at idle before driving. Do not turn off the engine for 30 minutes total of idle and/or driving as the battery may not have sufficient recharge to start.
Maintenance
(Continued) (cid:129) The electrical ignition system works with high voltage. Never touch these components with the engine running or the ignition switched on.
Failure to follow the above warn- ings can result in serious bodily injury or death.
CAUTION
(cid:129) When you don’t use the vehicle for a long time in the low temper- ature, remove the battery and store it indoors.
(cid:129) Always charge the battery fully to prevent the battery case from being damaged in low tempera- tures.
CALIFORNIA PROPOSI- TION 65 WARNING
Battery posts, terminals, and relat- ed accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer, birth defects and reproduc- tive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.
34
Maintenance
Reset items Items should be reset after the battery has been discharged or the battery has been disconnected. (cid:129) Auto up/down window (See section 4) (cid:129) Sunroof (See section 4) (cid:129) Trip computer (See section 4) (cid:129) Climate control system
(See section 4)
(cid:129) Clock (See section 4) (cid:129) Audio (See section 4)
WARNING
(cid:129) Before performing maintenance or recharging the battery, turn off all accessories and stop the engine.
(cid:129) The negative battery cable must be removed first and installed last when the battery is discon- nected.
(cid:129) Operation related to the battery should be done in an authorized HYUNDAI dealer.
WARNING - Recharging
battery
recharging
When the battery, observe the following precautions: (cid:129) The battery must be removed from the vehicle and placed in an area with good ventilation.
(cid:129) Do not allow cigarettes, sparks,
or flame near the battery.
(cid:129) Watch the battery during charg- ing, and stop or reduce the charg- ing rate if the battery cells begin gassing (boiling) violently or if the temperature of the electrolyte of any cell exceeds 120°F (49°C). (cid:129) Wear eye protection when check-
ing the battery during charging.
(cid:129) Disconnect the battery charger in
the following order.
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from
the negative battery terminal.
3. Unhook the positive clamp from
the positive battery terminal.
7 35
Maintenance
TIRES AND WHEELS Tire care For proper maintenance, safety, and maximum fuel economy, you must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your vehicle.
Recommended cold tire inflation pressures All tire pressures (including the spare) should be checked when the tires are cold. “Cold Tires” means the vehicle has not been driven for at least three hours or driven less than one mile (1.6 km). Recommended pressures must be maintained for the best ride, vehicle handling, and minimum tire wear. For recommended inflation pressure, refer to “Tire and wheels” in section 8.
36
CAUTION
(cid:129) Underinflation also results in excessive wear,poor handling and reduced fuel economy. Wheel deformation also is possible.Keep your tire pres- sures at the proper levels.If a tire frequently needs refilling, have it checked by an author- ized HYUNDAI dealer.
(cid:129) Overinflation produces a harsh ride, excessive wear at the center of the tire tread,and a greater possibility of dam- age from road hazards.
OMD060012N All specifications (sizes and pres- sures) can be found on a label attached to the driver’s side center pillar.
WARNING - Tire underin-
flation
Severe underinflation can lead to severe heat build-up, causing blowouts, tread separation and other tire failures that can result in the loss of vehicle control leading to severe injury or death. This risk is much higher on hot days and when driving for long periods at high speeds.
CAUTION
(cid:129) Warm tires normally exceed
recommended cold tire pres-
sures by 4 to 6 psi (28 to 41
kPa). Do not release air from
warm tires to adjust the pres-
sure or the tires will be under-
inflated.
(cid:129) Be sure to reinstall the tire inflation valve caps. Without the valve cap,dirt or moisture could get into the valve core and cause air leakage. If a valve cap is missing,install a new one as soon as possible.
WARNING - Tire Inflation Overinflation or underinflation can reduce tire life, adversely affect vehicle handling, and lead to sudden tire failure. This could result in loss of vehicle control and potential injury.
CAUTION - Tire pressure
Always observe the following:
(cid:129) Check tire pressure when the
tires are cold. (After vehicle
has been parked for at least
three hours or hasn't been
driven more than one mile (1.6
km) since startup.)
(cid:129) Check the pressure of your spare tire each time you check the pressure of other tires.
(cid:129) Never overload your vehicle. Be careful not to overload a vehicle luggage rack if your vehicle is equipped with one. (cid:129) Worn,old tires can cause acci- dents. If your tread is badly worn, or if your tires have been damaged,replace them.
Maintenance
Checking tire inflation pressure Check your tires once a month or more. Also, check the tire pressure of the spare tire.
How to check Use a good quality gage to check tire pressure. You can not tell if your tires are properly inflated simply by look- ing at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).
7 37
Maintenance
Remove the valve cap from the tire valve stem. Press the tire gage firm- ly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the tire and loading information label, no further adjust- ment is necessary. If the pressure is low, add air until you reach the rec- ommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and mois- ture.
38
Tire rotation To equalize tread wear, it is recom- mended that the tires be rotated every 7,500 miles (12,000 km) or sooner if irregular wear develops. During rotation, check the tires for correct balance. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out- of-balance wheels, severe braking or severe cornering. Look for bumps or bulges in the tread or side of tire. Replace the tire if you find either of these conditions. Replace the tire if fabric or cord is visible. After rotation, be sure to bring the front and rear tire pressures to specification and check lug nut tightness.
WARNING
(cid:129) Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.
(cid:129) Tires with too much or too little pressure wear unevenly caus- ing poor handling, loss of vehi- cle control, and sudden tire failure leading to accidents, injuries, and even death. The recommended cold tire pres- sure for your vehicle can be found in this manual and on the tire label located on the dri- ver's side center pillar.
(cid:129) Worn tires can cause acci- dents. Replace tires that are worn, show uneven wear, or are damaged.
(cid:129) Remember to check the pres- sure of your spare tire. HYUNDAI recommends that you check the spare every time you check the pressure of the other tires on your vehi- cle.
WARNING
(cid:129) Do not use the compact spare tire (if equipped) for tire rota- tion.
(cid:129) Do not mix bias ply and radial ply tires under any circum- stances. This may cause unusual handling characteris- tics that could result in death, severe injury, or property damage.
Without a spare tire
OBH078040
Disc brake pads should be inspected
for wear whenever tires are rotated.
✽✽ NOTICE Rotate radial tires that have an asymmetric tread pattern only from front to rear and not from right to left.
Maintenance
Wheel alignment and tire balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.
CAUTION
Improper wheel weights can damage your vehicle's alu- minum wheels. Use only approved wheel weights.
7 39
Maintenance
Tread wear indicator
OEN076053
Tire replacement If the tire is worn evenly, a tread wear indicator will appear as a solid band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. Replace the tire when this happens. Do not wait for the band to appear across the entire tread before replac- ing the tire.
40
WARNING - Replacing
tires