dangerous location in the event of a crash because it is not a pro- tected occupant space but mere- ly a part of the vehicle’s crush zone.
(cid:129) Your vehicle should be kept locked and keys be kept out of the reach of children. Parents should teach their children about the dangers of playing in trunks.
OHD046008
Emergency trunk safety release Your vehicle is equipped with an emer- gency trunk release cable located inside the trunk. The lever glows in the dark when the trunk lid is closed. If someone is inadvertently locked in the trunk, pulling this handle will release the trunk latch mechanism and open the trunk.
Features of your vehicle
4 13
Features of your vehicle
WINDOWS
Power windows (1) Driver’s door power window switch (2) Front passenger’s door power win-
dow switch
(3) Rear door (left) power window switch (4) Rear door (right) power window
switch
(5) Window opening and closing (6) Automatic power window up*/down*
(Driver’s window)
(7) Power window lock switch
*: if equipped
✽✽ NOTICE In cold and wet climates, power win- dows may not work properly due to freezing conditions.
OHD046009
14
The ignition switch must be in the ON
position for power windows to operate.
Each door has a power window switch
that controls the door’s window. However,
the driver has a power window lock
switch which can block the operation of
passenger windows.
The power windows can be operated for
approximately 30 seconds after the igni-
tion key is removed or turned to the ACC
or LOCK position. However, if the front
doors are opened, the power windows
cannot be operated even within the 30
seconds after the ignition key removal.
While driving, if you notice buffeting and
pulsation (wind shock) with either side
window open, you should open the oppo-
site window slightly to reduce the condi-
tion.
✽✽ NOTICE While driving with the rear windows down or with the sunroof (if equipped) in an open (or partially open) position, your vehicle may demonstrate a wind buffeting or pulsation noise. This noise is a normal occurrence and can be reduced or eliminated by taking the fol- lowing actions. If the noise occurs with one or both of the rear windows down, partially lower both front windows approximately one inch. If you experi- ence the noise with the sunroof open, slightly reduce the size of the sunroof opening.
CAUTION
(cid:129) To prevent the power window system from the possibility of damage,do not open or close two windows at the same time. This will also ensure the longevity of the fuse.
(cid:129) Never try to operate the main switch on the driver's door and the individual door window switch in opposing directions at the same time.If this is done,the window will stop and cannot be opened or closed.
Features of your vehicle
WARNING - Windows
(cid:129) Always double check to make sure all arms, hands, head and other obstructions are safely out of the way before closing a win- dow.
(cid:129) Do not allow children to play with the power windows. Keep the dri- ver’s door power window lock switch in the LOCK position (depressed). Serious injury can result from unintentional window operation by the child.
(cid:129) Do not extend face or arms out- side through the window opening while driving.
4 15
Features of your vehicle
Window opening and closing The driver’s door has a master power window switch that controls all the win- dows in the vehicle. (cid:129) To open or close a window, press down or pull up the front portion of the corre- sponding switch to the first detent posi- tion (5).
Auto down window (if equipped) (driver’s window) Depressing the power window switch momentarily to the second detent posi- tion (6) completely lowers the driver’s window even when is released. To stop the window at the desired position while the window is in operation, momentarily pull the switch in the direction opposite of the window movement.
the switch
Auto up/down window (if equipped) (Driver's window) Depressing or pulling up the power win- dow switch momentarily to the second detent position (6) completely lowers or lifts the window even when the switch is released. To stop the window at the desired position while the window is in operation, pull up or depress and release the switch to the opposite direction of the movement. If the power window is not operating cor- rectly, the automatic power window sys- tem must be reset as follows: 1. Turn the ignition switch to the ON posi-
tion.
2. Close driver’s window and continue pulling up on driver’s power window switch for at least 1 second after the window is completely closed.
Automatic reversal If the upward movement of the driver’s window is blocked by an object or part of the body, the window will detect the resistance and will stop upward move- ment. The window will then lower approx- imately 12 in. (30 cm) to allow the object to be cleared. If the window detects resistance while the power window switch is pulled up continuously, the window will stop upward movement then lower approxi- mately 1in. (2.5cm). If the power window switch is pulled up continuously again within 5 seconds after the window is low- ered by the automatic window reversal feature, the automatic window reversal will not operate.
16
WARNING
(cid:129) The automatic reverse feature for the driver’s window is only active when the “auto up” feature is used by fully pulling up the switch. The automatic reverse feature will not operate if the win- dow is raised using the halfway position on the power window switch.
(cid:129) Always check for obstructions
before raising any window to
avoid injuries or vehicle damage.
If an object less than 0.16 in. (4
mm)
is caught
between the window glass and
the upper window channel, the
automatic reverse window may
not detect the resistance and will
not stop and reverse direction.
in diameter
WARNING
(cid:129) Passengers can be injured if their head, hands or other body parts are trapped by a closing window. Always check for obstructions before raising any window.
(cid:129) NEVER leave the ignition key in
the vehicle.
(cid:129) NEVER leave any child unattend- ed in the vehicle. Even very young children may inadvertently cause the vehicle to move, entan- gle themselves in the windows, or otherwise injure themselves or others.
Features of your vehicle
OHD046010
Power window lock button (cid:129) The driver can disable the power win- dow switches on a passenger door by depressing the power window lock switch located on the driver’s door to LOCK (pressed).
(cid:129) When the power window lock switch is ON, the driver’s master control cannot operate the passenger door power windows.
4 17
Features of your vehicle
HOOD
OHD046011
Opening the hood 1. Pull the release lever to unlatch the hood. The hood should pop open slightly.
OHD046012
2. Go to the front of the vehicle, raise the
hood slightly, pull the secondary latch
(1) inside of the hood center and lift
the hood (2).
OHD046013
3.Pull the support rod from the engine
room.
4.Hold the hood open with the support
rod.
WARNING - Hot parts
Grasp the support rod in the area wrapped in rubber. The rubber will help prevent you from being burned by hot metal when the engine is hot.
18
WARNING
(cid:129) Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could fly open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident. (cid:129) The support rod must be inserted completely into the hole provided in the hood whenever you inspect the engine compartment.This will prevent the hood from falling and possibly injuring you.
(cid:129) Do not move the vehicle with the hood in the raised position, as vision is obstructed and the hood could fall or be damaged.
Closing the hood 1. Before closing the hood, check the fol-
lowing: (cid:129) All filler caps in engine compartment
must be correctly installed.
(cid:129) Gloves, rags or any other com- bustible material must be removed from the engine compartment.
2. Return the support rod to its clip to
prevent it from rattling.
3. Lower the hood until it is about 1 ft. (30
cm) above the closed position and let
it drop. Make sure that it locks into
place.
WARNING
Make sure the hood is properly locked before driving.
Features of your vehicle
WARNING - Hood
(cid:129) Before closing the hood, ensure that all obstructions are removed from the hood opening. Closing the hood with an obstruction present in the hood opening may result in property damage or severe personal injury.
(cid:129) Do not leave gloves, rags or any other combustible material in the engine compartment. Doing so may cause a heat-induced fire.
4 19
Features of your vehicle
FUEL FILLER LID
OHD046014
OUN026020
Opening the fuel filer lid The fuel-filler lid must be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.
✽✽ NOTICE If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved de-icer fluid (do not use radi- ator anti-freeze) or move the vehicle to a warm place and allow the ice to melt.
1. Stop the engine. 2. To open the fuel filler lid, pull the fuel
filler lid opener up.
WARNING
To avoid injury from sharp edges, it is recommended that protective gloves be worn if there is a need to open the fuel filler door manually.
3. Pull the fuel filler lid out to open. 4. To remove the cap, turn the fuel tank
cap counterclockwise.
5. Refuel as needed.
20
Closing the fuel filler lid 1. To install the cap, turn it clockwise until it “clicks”. This indicates that the cap is securely tightened.
2. Close the fuel filler lid and push it light- ly and make sure that it is securely closed.
WARNING - Refueling
(cid:129) If pressurized fuel sprays out, it can cover your clothes or skin and thus subject you to the risk of fire and burns. Always remove the fuel cap carefully and slowly. If the cap is venting fuel or if you hear a hissing sound, wait until the condition stops before com- pletely removing the cap.
(cid:129) Do not "top off" after the nozzle automatically shuts off when refueling.
(cid:129) Tighten the cap until it clicks, oth- " light will illumi-
erwise the " nate.
(cid:129) Always check that the fuel cap is installed securely to prevent fuel spillage in the event of an acci- dent.
WARNING - Refueling dan-
gers
Automotive fuels are flammable materials. When refueling, please note the following guidelines care- fully. Failure to follow these guide- lines may result in severe personal injury, severe burns or death by fire or explosion. (cid:129) Read and follow all warnings posted at the gas station facility. (cid:129) Before refueling note the location of the Emergency Gasoline Shut- Off, if available, at the gas station facility.
(cid:129) Before touching the fuel nozzle, you should eliminate potentially dangerous static electricity dis- charge by touching another metal part of the vehicle, a safe dis- tance away from the fuel filler neck, nozzle, or other gas source. (Continued)
(Continued) (cid:129) Do not get back into a vehicle once you have begun refueling since you can generate static electricity by touching, rubbing or sliding against any item or fab- ric (polyester, satin, nylon, etc.) capable of producing static elec- tricity. Static electricity discharge can ignite fuel vapors resulting in rapid burning. If you must re- enter the vehicle, you should once again eliminate potentially dangerous static electricity dis- charge by touching a metal part of the vehicle, away from the fuel filler neck, nozzle or other gaso- line source.
(cid:129) When using
an
the container on
approved portable fuel container be sure to place the ground prior to refueling. Static electricity discharge from the container can ignite fuel vapors causing a fire. Once refueling has begun, contact with the vehi- cle should be maintained until the filling is complete.
Features of your vehicle
(Continued)
Use only approved portable plas- tic fuel containers designed to carry and store gasoline.
(cid:129) Do not use cellular phones while refueling. Electric current and/or electronic interference from cel- lular phones can potentially ignite fuel vapors causing a fire. (cid:129) When refueling, always shut the engine off. Sparks produced by electrical components related to the engine can ignite fuel vapors causing a fire. Once refueling is complete, check to make sure the filler cap and filler door are securely closed, before starting the engine.
(cid:129) DO NOT use matches or a lighter and DO NOT SMOKE or leave a lit cigarette in your vehicle while at a gas station especially during refueling. Automotive fuel is highly flammable and can, when ignited, result in fire.
(Continued)
(Continued)
4 21
Features of your vehicle
(Continued) (cid:129) If a fire breaks out during refuel- ing, leave the vicinity of the vehi- cle, and immediately contact the manager of the gas station and then contact the local fire depart- ment or 911. Follow any safety instructions they provide.
CAUTION
(cid:129) Make sure to refuel with unleaded
fuel only.
(cid:129) If the fuel filler cap requires replacement, use only a genuine Hyundai cap or the equivalent specified for your vehicle. An incorrect fuel filler cap can result in a serious malfunction of the fuel system or emission control system.
(cid:129) Do not spill fuel on the exterior surfaces of the vehicle.Any type of fuel spilled on painted surfaces may damage the paint.
(cid:129) If the fuel filler lid will not open in cold weather because the area around it is frozen,push or lightly tap the lid.
(cid:129) After refueling,make sure the fuel cap is installed securely to pre- vent fuel spillage in the event of an accident.
22
Features of your vehicle
✽✽ NOTICE The sunroof cannot slide when it is in the tilt position nor can it be tilted while in an open or slide position.
WARNING
Never adjust the sunshade while driving. This could result in loss of control and an accident that may cause death, serious injury, or property damage.
✽✽ NOTICE In cold and wet climates, sunroof may not work properly due to freezing con- ditions. ✽✽ NOTICE After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.
CAUTION
Do not continue to press the sun- roof control button(s) after the sun- roof is in the fully open,closed,or tilt position(s).Damage to the motor or system components could occur.
SUNROOF (IF EQUIPPED)
OHD046016
If your vehicle is equipped with this fea-
ture, you can slide or tilt your sunroof
with the sunroof control buttons located
on the overhead console.
1. Slide button
2. Tilt button
3. Close button
The sunroof can only be opened, closed, or tilted when the ignition switch is in the ON position.
4 23
Features of your vehicle
OHD046017
OUN026027
OHD046018
Sliding the sunroof To open the sunroof (autoslide feature), press the slide button (1) on the over- head console (for more than 0.5 sec- onds). The sunroof will slide all the way open. To stop the sunroof sliding at any point, press any sunroof control button. To close the sunroof (autoslide feature), press the close button (3) on the over- head console (for more than 0.5 sec- onds). The sunroof will slide all the way close. To stop the sunroof sliding at any point, press any sunroof control button.
24
Automatic reversal If an object or part of the body is detect- ed while the sunroof is closing automati- cally, it will reverse direction, and then stop. Auto reverse function does not work if a tiny obstacle is blocked between the slid- ing glass and the sunroof sash. You should always check that all passengers and objects are away from the sunroof before closing it.
Tilting the sunroof To open the sunroof (autotilt feature), press the tilt button (2) on the overhead console (for more than 0.5 seconds). The sunroof will tilt all the way open. To stop the sunroof tilting at any point, press any sunroof control button. To close the sunroof, press the close but- ton (3) on the overhead console and hold it until the sunroof is closed.
WARNING
Be careful that someone’s head, hands and body are not trapped by a closing sunroof.
WARNING - Sunroof
(cid:129) Be careful that no heads, hands and body parts are obstructing a closing sunroof.
(cid:129) Do not extend the face, neck, arms or body outside the sunroof while driving.
(cid:129) Make sure your hands and head are safely out of the way before closing a sunroof.
Features of your vehicle
CAUTION
(cid:129) Do not press any sunroof control button longer than necessary. Damage to the motor or system components could occur.
(cid:129) Periodically remove any dirt that may accumulate on the guide rail. (cid:129) If you try to open the sunroof when the temperature is below freezing or when the sunroof is covered with snow or ice, the glass or the motor could be dam- aged.
(cid:129) The sunroof is made to slide together with sunshade. Do not leave the sunshade closed while the sunroof is open.
OUN026031
Sunshade The sunshade will be opened with the glass panel automatically when the glass panel is slid.You will have to close it man- ually if you want it closed.
4 25
❈ For more detailed information, contact
an authorized HYUNDAI dealer.
CAUTION
If the sunroof is not reset when the vehicle battery is disconnected or discharged, or related fuse is blown, the sunroof may operate improperly.
Features of your vehicle
Resetting the sunroof Whenever the vehicle battery is discon- nected or discharged, or related fuse is blown, you must reset your sunroof sys- tem as follows:
1. Turn the ignition switch to the ON position and close the sunroof com- pletely.
2. Release the control button. 3. Press and hold the close button until the sunroof tilts and slightly moves up and down. Then, release the button.
4. Press and hold the close button until
the sunroof is operated as follows;
TILT DOWN → SLIDE OPEN → SLIDE CLOSE
Then, release the control button.
When this is complete, the sunroof sys- tem is reset.
26
Features of your vehicle
Tilt steering Tilt steering allows you to adjust the steering wheel before you drive. You can also raise it to give your legs more room when you exit and enter the vehicle.
The steering wheel should be positioned so that it is comfortable for you to drive, while permitting you to see the instru- ment panel warning lights and gauges.
STEERING WHEEL Electronic power steering Power steering uses the motor to assist you in steering the vehicle. If the engine is off or if the power steering system becomes inoperative, the vehicle may still be steered, but it will require increased steering effort. The motor driven power steering is con- trolled by power steering control unit which sense the steering wheel torque, steering wheel position and vehicle speed to command the motor. The steering wheel becomes heavier as the vehicle’s speed increases and becomes lighter as the vehicle’s speed decreases for the better control of the steering wheel. Should you notice any change in the effort required to steer during normal vehicle operation, have the power steer- ing checked by an authorized Hyundai dealer.
✽✽ NOTICE The following symptoms may occur dur- ing normal vehicle operation: • The EPS warning light does not illumi-
nate.
• The steering wheel becomes heavier after turning the ignition switch on. This happens as the system performs the EPS system diagnostics. When the diagnostics is completed, the steering wheel will return to its normal condi- tion.
• Click noise may be heard from the EPS relay after the ignition switch is turned to the ON or LOCK position.
• Motor noise may be heard when the vehicle is at a stop or at a low driving speed.
• The steering effort can suddenly increase, if the operation of EPS sys- tem is stopped to prevent serious acci- dents when the malfunction of EPS system is detected by self-diagnosis.
4 27
Features of your vehicle
WARNING
(cid:129) Never adjust the angle and height of steering wheel while driving. You may lose your steering con- trol and cause severe personal injury or accidents.
(cid:129) After adjusting, push the steering wheel both up and down to be certain it is locked in position.
28
OHD046021
To change the steering wheel angle, pull
down the lock release lever (1), adjust
the steering wheel to the desired angle
(2) and height (3, if equipped), then pull
up the lock-release lever to lock the
steering wheel in place. Be sure to adjust
the steering wheel to the desired position
before driving.
OHD046022
Horn To sound the horn, press the horn sym- bol on your steering wheel. Check the horn regularly to be sure it operates properly.
CAUTION
(cid:129) To sound the horn,press the area indicated by the horn symbol on your steering wheel (see illustra- tion).The horn will operate only when this area is pressed.
(cid:129) Do not strike the horn severely to operate it,or hit it with your fist. Do not press on the horn with a sharp-pointed object.
MIRRORS Inside rearview mirror Day/night rearview mirror Adjust the rearview mirror to center on the view through the rear window. Make this adjustment before you start driving.
WARNING - Rear visibility Do not place objects in the rear seat or cargo area which would interfere with your vision out the rear window.
OHD046023
Make this adjustment before you start
driving and while the day/night lever is in
the day position.
Pull the day/night lever toward you to
reduce glare from the headlights of vehi-
cles behind you during night driving.
Remember that you lose some rearview
clarity in the night position.
Features of your vehicle
Electric chromic mirror (ECM) (if equipped) The electric rearview mirror automatical- ly controls the glare from the headlights of the car behind you in nighttime or low light driving conditions. The sensor mounted in the mirror senses the light level around the vehicle, and through a chemical reaction, automatically controls the headlight glare from vehicles behind you. When the engine is running, the glare is automatically controlled by the sensor mounted in the rearview mirror. Whenever the shift lever is shifted into reverse (R), the mirror will automatically go to the brightest setting in order to improve the drivers view behind the vehi- cle.
CAUTION
When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liq- uid cleaner to enter the mirror hous- ing.
4 29
Features of your vehicle
Indicator light
Glare detection sensor
OHD046024
To operate the electric rearview mirror (cid:129) Press the ON/OFF button (1) to turn the automatic dimming function on. The mirror indicator light will illuminate. Press the ON/OFF button to turn the automatic- dimming function off. The mirror indicator light will turn off.
(cid:129) The mirror defaults to the ON position whenever the ignition switch is turned on.
OHD046025N Electric chromic mirror with homelink system (if equipped) To operate the electric rearview mirror Press the I button (1) to turn the auto- matic- dimming function on. The mirror indicator light will illuminate. Press the O button (2) to turn the auto- matic- dimming function off. The mirror indicator light will turn off.
Homelink buttons
OHD046305N
HomeLink® Wireless Control System Your new mirror comes with an integrat- ed HomeLink Universal Transceiver, which allows you to program the mirror to activate your garage door(s), estate gate, home lighting, etc. The mirror actually learns the codes from your various exist- ing transmitters.
30
WARNING
(cid:129) When
programming
the HomeLink® Wireless Control System, you may be operating a garage door or gate operator. Make sure that people and objects are out of the way of the moving door or gate to prevent potential harm or damage.
(cid:129) Do not use HomeLink with any garage door opener that lacks the safety stop and reverse feature as required by federal safety standards. (This includes any garage door opener model manu- factured before April 1, 1982.) A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases risk of serious injury or death. For more information, call 1-800-355-3515 or on the internet at www.homelink.com.
Features of your vehicle
Flashing
Retain the original transmitter for future programming procedures (i.e., new vehi- cle purchase). It is also suggested that upon the sale of the vehicle, the pro- grammed HomeLink buttons be erased for security purposes (follow step 1 in the “Programming” portion of this text).
Programming Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of HomeLink. It is also recommended that a new battery be replaced in the hand-held transmitter of the device being pro- grammed to HomeLink for quicker train- ing and accurate transmission of the radio-frequency. Follow HomeLink mirror:
these steps
train your
to
OHD046306N 1. When programming the buttons for the first time, press and hold the left and ) simultane- center buttons ( ously until the indicator light begins to flash after approximately 20 seconds. (This procedure erases the factory-set default codes. Do not perform this step to program additional hand-held trans- mitters.)
4 31
Features of your vehicle
✽✽ NOTICE For non rolling code garage door open- ers, follow steps 2 - 3. For rolling code garage door openers, follow steps 2 - 6. For Canadian Programming, please fol- low the Canadian Programming section. For help with determining whether your garage is non-rolling code or rolling code, please refer to the garage door openers owner’s manual or contact HomeLink customer service at 1-800- 355-3515.
32
Flashing
1-3inches
Transmitter
OHD046307N
2. Press and hold the button on the
HomeLink system you wish to train
and the button on the transmitter while
the transmitter is approximately 1 to 3
inches away from the mirror. Do not
release the buttons until step 3 has
been completed.
3. The HomeLink indicator light will flash, first slowly and then rapidly. When the indicator light flashes rapidly, both but- tons may be released. (The rapid flash- ing light indicates successful program- ming of the new frequency signal.)
✽✽ NOTICE Some gate operators and garage door openers may require you to replace step #3 with the “cycling” procedure noted in the “Canadian Programming” section of this document.
Rolling code programming To train a garage door opener (or other rolling code equipped devices) with the rolling code feature, follow these instruc- tions after completing the “Programming” portion of this text. (A second person may make the following training proce- dures quicker & easier.) 4. Locate the “learn” or “smart” button on the device’s motor head unit. Exact location and color of the button may vary by product brand. If there is diffi- culty locating the “learn” or “smart” but- ton, reference the device’s owner’s manual or contact HomeLink at 1-800- 355-3515 or on internet at www.homelink.com.
the
5. Press and release the “learn” or “smart” button on the device’s motor head unit. You have 30 seconds to complete step number 6.
the
release
6. Return to the vehicle and firmly press and programmed HomeLink button up to three times. The rolling code equipped device should now recognize the HomeLink signal and activate when the HomeLink button is pressed. The remaining two buttons may now be programmed if this has not previously been the “Programming” portion of this text.
Refer
done.
to
Operating HomeLink To operate, simply press the pro- grammed HomeLink button. Activation will now occur for the trained product (garage door, security system, entry door lock, estate gate, or home or office light- ing). For convenience, the hand-held transmitter of the device may also be used at any time. The HomeLink Wireless Controls System (once pro- grammed) or the original hand-held transmitter may be used to activate the device (e.g. garage door, entry door lock, etc.). In the event that there are still pro- gramming difficulties, contact HomeLink at 1-800-355-3515 or on the internet at www.homelink.com.
Flashing
OHD046306N
Erasing programmed HomeLink but-
tons
To erase the three programmed buttons
(individual buttons cannot be erased):
(cid:129) Press and hold the left and center
buttons simultaneously, until the indi-
cator light begins to flash (approxi-
mately 20 seconds). Release both but-
tons. Do not hold for longer than 30
seconds.
HomeLink is now in the train (or learning) mode and can be programmed at any time.
Features of your vehicle
Reprogramming a single HomeLink
button
To program a device to HomeLink using
a HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button. Do NOT release until step 4
has been completed.
2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 to 3 inches away from the HomeLink surface.
3. Press and hold the hand-held trans- mitter button (or press and “cycle” - as described in “Canadian Programming” above).
4. The HomeLink indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The previous device has now been erased and the new device can be acti- vated by pushing the HomeLink button that has just been programmed. This pro- cedure will not affect any other pro- grammed HomeLink buttons.
4 33
Accessories If you would like additional information on the HomeLink Wireless Control System, HomeLink compatible products, or to purchase other accessories such as the HomeLink® Lighting Package, please contact HomeLink at 1-800-355-3515 or on the internet at www.homelink.com.
FCC ID: NZLZTVHL3
IC: 4112A-ZTVHL3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful
interference, and
2. This device must accept any interfer- ence received, including interference that may cause undesired operation.
WARNING
The transceiver has been tested and complies with FCC and Industry Canada rules. Changes or modifications expressly approved by the party responsible for compliance could void the user's authority to operate the device.
not
Features of your vehicle
Gate operator programming & canadi-
an programming
During programming, your hand-held
transmitter may automatically stop trans-
mitting. Continue to press and hold the
HomeLink button (note steps 2 through 4
in the “Programming” portion of this text)
while you press and re-press (“cycle”)
your handheld transmitter every two sec-
onds until the frequency signal has been
learned. The indicator light will flash
slowly and then rapidly after several sec-
onds upon successful training.
CAUTION
If programming a garage door opener or gate, it is advised to unplug the device during the “cycling”process to prevent possi- ble motor burn-up.
34
Outside rearview mirror Be sure to adjust mirror angles before driving. Your vehicle is equipped with both left- hand and right-hand outside rearview mirrors. The mirrors can be adjusted remotely with the remote switch. The mir- ror heads can be folded back to prevent damage during an automatic car wash or when passing in a narrow street.
Features of your vehicle
CAUTION
If the mirror is jammed with ice,do not adjust the mirror by force.Use an approved spray de-icer (not radi- ator antifreeze) to release the frozen mechanism or move the vehicle to a warm place and allow the ice to melt.
WARNING
Do not adjust or fold the outside rearview mirrors while the vehicle is moving. This could result in loss of control, and an accident which could cause death, serious injury or property damage.
WARNING - Rearview mir-
rors
(cid:129) The right outside rearview mirror is convex. Objects seen in the mirror are closer they appear.
than
(cid:129) Use your interior rearview mirror or direct observation to deter- mine the actual distance of fol- lowing vehicles when changing lanes.
CAUTION
Do not scrape ice off the mirror face;this may damage the surface of the glass. If ice should restrict movement of the mirror, do not force the mirror for adjustment.To remove ice,use a deicer spray,or a sponge or soft cloth with very warm water.
4 35
CAUTION
(cid:129) The mirrors stop moving when they reach the maximum adjust- ing angles,but the motor contin- ues to operate while the switch is depressed. Do not depress the switch longer than necessary,the motor may be damaged.
(cid:129) Do not attempt to adjust the out- side rearview mirror by hand. Doing so may damage the parts.
Features of your vehicle
B510A01E
OHD046025
Remote control Manual type (if equipped) The outside rearview mirrors are equipped with a remote control for your convenience. It is operated by the control lever in the bottom front corner of the window. Before driving away, always check that your mirrors are positioned so you can see behind you, both to the left and right sides, as well as directly behind your vehicle. When using the mirror, always exercise caution when attempting to judge the distance of vehicles behind or along side of you.
Electric type (if equipped) The electric remote control mirror switch allows you to adjust the position of the left and right outside rearview mirrors. To adjust the position of either mirror, move the lever (1) to R or L to select the right side mirror or the left side mirror, then press a corresponding point ( ) on the mirror adjustment control to position the selected mirror up, down, left or right. After adjustment, put the lever into neu- tral position to prevent the inadvertent adjustment.
36
B510E01E
Folding the outside rearview mirror To fold outside rearview mirror, grasp the housing of mirror and then fold it toward the rear of the vehicle.
Features of your vehicle
4 37
Features of your vehicle
INSTRUMENT CLUSTER ■■ Type A
■■ Type B
38
1. Tachometer 2. Turn signal indicators 3. Speedometer 4. Warning and indicator lights 5. Shift position indicator
(Automatic transaxle only)
6. Odometer/Trip computer (if equipped) 7. Fuel gauge 8. Engine temperature gauge (if equipped)
* The actual cluster in the vehicle may differ
from the illustration. For more details refer to the "Gauges" in the next pages.
OHD049500N/OHD040552N
Features of your vehicle
■ Type A
■ Type B
■ Type A
■ Type B
OHD046045L
OHD046028N/OHD040553N
OHD046029/OHD040554
Instrument panel illumination When the vehicle’s parking lights or head- lights are on, rotate the illumination con- trol knob to adjust the brightness of the instrument panel illumination. The brightness of instrument panel illu- mination can be adjusted by rotating the control knob with the headlight switch in any position when the ignition switch is in ON position.
Gauges Speedometer The speedometer indicates the forward speed of the vehicle. The speedometer is calibrated in miles per hour and/or kilometers per hour.
Tachometer The tachometer indicates the approxi- mate number of engine revolutions per minute (rpm). Use the tachometer to select the correct shift points and to prevent lugging and/or over-revving the engine. When the door is open, and if the engine is not started in 1 minute, the tachometer pointer may move slightly in ACC or ON position with the engine OFF. This move- ment is normal and will not affect the accuracy of the tachometer once the engine is running.
CAUTION
Do not operate the engine within the tachometer's RED ZONE. This may cause severe engine damage.
4 39
Features of your vehicle
OHD040555
Engine temperature gauge (if equipped) This gauge shows the temperature of the engine coolant when the ignition switch is ON. Do not continue driving with an overheat- ed engine. If your vehicle overheats, refer to “If the engine overheats” in section 6.
CAUTION
If the gauge pointer moves beyond the normal range area toward the “H”position, it indicates overheat- ing that may damage the engine.
40
■ Type A
■ Type B
WARNING
Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could cause severe burns. Wait until the engine is cool before adding coolant to the reservoir.
OHD049031/OHD040556
Fuel gauge The fuel gauge indicates the approxi- mate amount of fuel remaining in the fuel tank. The fuel tank capacity is given in sec- tion 8. The fuel gauge is supplemented by a low fuel warning light, which will illumi- nate when the fuel tank is nearly empty.
WARNING - Fuel gauge
Running out of fuel can expose vehicle occupants to danger. You must stop and obtain addition- al fuel as soon as possible after the warning light comes on or when the gauge indicator comes close to the E level.
Features of your vehicle
CAUTION
Avoid driving with a very low fuel level.If you run out of fuel,it could cause the engine to misfire and result in excessive loading of the catalytic converter.
OHD046035
OHD049933C
Odometer / Tripmeter (if equipped) You can choose the odometer, tripmeter A, tripmeter B or ECO indicator ON/OFF mode (if equipped) by pressing the TRIP button for less than 1 second.
Odometer
Tripmeter
ECO ON/OFF mode*
* : If equipped
Odometer The odometer indicates the total dis- tance the vehicle has been driven. You will also find the odometer useful to determine when periodic maintenance should be performed.
✽✽ NOTICE It is forbidden that alteration of the odometer of any vehicle with the intent to change the mileage registered on the odometer. The alteration may void your warranty coverage.
4 41
Features of your vehicle
OHD049934C
OHD040550
OHD046035
Tripmeter TRIP A: Tripmeter A TRIP B: Tripmeter B The tripmeter indicates the distance of individual trips selected by the driver. Tripmeter A or B can be reset to 0 by pressing the TRIP button for 1 second or more, and then releasing.
ECO ON/OFF mode (if equipped)
You can turn the ECO indicator on/off on
the instrument cluster in this mode.
If you push the TRIP button more than 1
second in the ECO ON mode, ECO OFF
is displayed and the ECO indicator turns
off.
If you want to display the ECO indicator
again, press the TRIP button more than 1
second in the ECO OFF mode and then
ECO ON mode is displayed.
For more detailed explanations, refer to
"Warnings and indicators" in section 4.
Trip computer (if equipped) The trip computer is a microcomputer- controlled driver information system that displays information related to driving, including distance to empty, tripmeter, average fuel consumption and average speed on the display when the ignition switch is in ON position.
42
The odometer is always displayed until the display is turned off. Press the TRIP button for less than 1 sec- ond to select each function as follows :
■ Type A
■ Type A
Features of your vehicle
Tripmeter
Distance to empty
Average fuel consumption
Instant fuel consumption*
Average speed
Driving time*
ECO ON/OFF mode*
* : if equipped
■ Type B
Tripmeter
OHD040558N
■ Type B
OHD040559N
Odometer
OHD049043N
Tripmeter
This mode indicates the total distance
travelled since the last tripmeter reset.
Total distance is also reset to zero if the
battery is disconnected.
Pressing the TRIP button for more than 1
second when the tripmeter is being dis-
played clears the tripmeter to zero.
The meter's working range is from 0 to
999.9 miles.
OHD040041N
Distance to empty
This mode indicates the estimated dis-
tance to empty based on the current fuel
in the fuel tank and the amount of fuel
delivered to the engine. When the
remaining distance is below 30 miles (50
km), a “---” symbol will be displayed.
The meter’s working range is from 30 to
999 miles (50 to 999 km).
4 43
Features of your vehicle
✽✽ NOTICE • If the vehicle is not on level ground or the battery power has been interrupt- ed, the “Distance to empty” function may not operate correctly. The trip computer may not register additional fuel if less than 1.6 gallons (6 liters) of fuel are added to the vehi- cle.
• The fuel consumption and distance to empty values may vary significantly based on driving conditions, driving habits, and condition of the vehicle.
• The distance to empty value is an esti- mate of the available driving distance. This value may differ from the actual driving distance available.
44
■ Type A
The meter's working range is from 0.1 to
99.9 miles per gallon (0.1 to 99.9 l/100
km).
Press the TRIP button for more than 1
second to reset the average fuel con-
sumption to zero (---).
■ Type B
OHD040561N
OHD049039N
Average fuel consumption This mode calculates the average fuel consumption from the total fuel used and the distance since the last average con- sumption reset. The total fuel used is cal- culated from the fuel consumption input. For an accurate calculation, drive more than 0.03 miles (50 m).
■ Type A
■ Type A
■ Type A
Features of your vehicle
OHD040560N
Instant fuel consumption (if equipped) This mode calculates the instant fuel consumption every 2 seconds from the driving distance and quantity of fuel injection.
■ Type B
OHD040562N
OHD049040N
Average speed
This mode indicates the average speed
from the starting of the engine to the igni-
tion key "OFF".
Average speed is reset to zero if the bat-
tery is disconnected.
To reset the average speed to zero (---),
press the TRIP button for more than 1
second.
The meter’s working range is from 0 to
999 MPH.
OHD040563N
Driving time (if equipped)
This mode indicates the total time trav-
eled since the last driving time reset.
Even if the vehicle is not in motion, the
driving time keeps going while the engine
is running.
The meter’s working range is from
00:00~99:59.
Pressing the TRIP button for more than 1
second, when the driving time is being
displayed, clears the driving time to zero
(00:00).
4 45
Warnings and indicators All warning lights are checked by turning the ignition switch ON (do not start the engine). Any light that does not illuminate should be checked by an authorized Hyundai dealer. After starting the engine, check to make sure that all warning lights are off. If any are still on, this indicates a situation that needs attention. When releasing the parking brake, the brake system warning light should go off. The fuel warning light will stay on if the fuel level is low.
Air bag warning light
This warning light will illuminate for approximately 6 seconds each time you turn the ignition switch to the ON posi- tion. This light also comes on when the SRS is not working properly. If the air bag warning light does not come on, or con- tinuously remains on after operating for about 6 seconds when you turned the ignition switch to the ON position or start- ed the engine, or if it comes on while driving, have the SRS inspected by an authorized Hyundai dealer.
Features of your vehicle
■ Type A
■ Type B
OHD040564
OHD040551
ECO ON/OFF mode (if equipped)
You can turn the ECO indicator on/off on
the instrument cluster in this mode.
If you push the TRIP button more than 1
second in the ECO ON mode, ECO OFF is
displayed and the ECO indicator turns off.
If you want to display the ECO indicator
again, press the TRIP button more than 1
second in the ECO OFF mode and then
ECO ON mode is displayed.
For more detailed explanations, refer to
"Warnings and indicators" in section 4.
46
Anti-lock brake system (ABS) warning light (if equipped)
This light illuminates if the ignition switch is turned to ON and goes off in approxi- mately 3 seconds if the system is operat- ing normally. If the ABS warning light remains on, comes on while driving, or does not come on when the ignition switch is turned to the ON position, this indicates that there may be a problem with the ABS. If this occurs, have your vehicle checked by an authorized Hyundai dealer as soon as possible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.
Electronic brake force distri- bution (EBD) system warning light If these two warning lights illuminate at the same time while driving, your vehicle has a problem with ABS and EBD system. In this case, your ABS and regular brake system may not work normally. Have the vehicle checked by an authorized Hyundai dealer as soon as possible.
WARNING
If the both ABS and Brake warning lights are on and stay on, your vehi- cle’s brake system will not work normally. So you may experience an unexpected and dangerous situ- ation during sudden braking. In this case, avoid high speed driving and abrupt braking. Have your vehicle checked by an authorized Hyundai dealer as soon as possible.
Features of your vehicle
Seat belt warning
Seat belt warning light If the driver's seat belt is not fastened when the ignition key is turned ON, the seat belt warning light blinks for approxi- mately 6 seconds. And if the vehicle speed exceeds 6 mph (10 km/h) with the seat belt unfastened, the seat belt warn- ing light blinks with the pattern of 6 sec- onds on and 24 seconds off for 11 times. The seat belt warning light will stop if the seat belt is fastened or the vehicle speed is reduced to below 3 mph (5 km/h).
Seat belt warning chime
If the driver's seat belt is not fastened
when the ignition key is turned ON, the
seat belt warning chime sounds for
approximately 6 seconds. And if the vehi-
cle speed exceeds 6 mph (10 km/h) with
the seat belt unfastened, the seat belt
warning chime sounds with the pattern of
6 seconds on and 24 seconds off for 11
times. The seat belt warning chime will
stop if the seat belt is fastened or the
vehicle speed is reduced to below 3 mph
(5 km/h).
4 47
Features of your vehicle
Turn signal indicator lights
Engine oil pressure warn- ing
This warning light indicates the engine oil pressure is low. If the warning light illuminates while driv- ing: 1. Drive safely to the side of the road and
stop.
2. With the engine off, check the engine oil level. If the level is low, add oil as required.
If the warning light remains on after adding oil or if oil is not available, call an authorized Hyundai dealer.
CAUTION
If the engine is not stopped imme- diately after the engine oil pressure warning light is illuminated,severe damage could result.
The blinking green arrows on the instru- ment panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illuminate at all, a malfunction in the turn signal system is indicated. Your dealer should be consult- ed for repairs.
High beam indicator
This indicator illuminates when the head- lights are on and in the high beam posi- tion or when the turn signal lever is pulled into the Flash-to-Pass position.
Tail light indicator (if equipped)
This indicator illuminates when the tail lights are on.
48
CAUTION
If the oil pressure warning light stays on while the engine is run- ning, serious engine damage may result. The oil pressure warning light comes on whenever there is insufficient oil pressure. In normal operation,it should come on when the ignition switch is turned on, then go out when the engine is started.If the oil pressure warning light stays on while the engine is running,there is a serious malfunc- tion. If this happens, stop the car as soon as it is safe to do so,turn off the engine and check the oil level.If the oil level is low,fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the engine off immediately. In any instance where the oil light stays on when the engine is running, the engine should be checked by an authorized Hyundai dealer before the car is driven again.
Parking brake & brake fluid warning
Parking brake warning This light is illuminated when the parking brake is applied with the ignition switch in the START or ON position. The warning light should go off when the parking brake is released.
Low brake fluid level warning If the warning light remains on, it may indicate that the brake fluid level in the reservoir is low. If the warning light remains on: 1. Drive carefully to the nearest safe
location and stop your vehicle.
2. With the engine stopped, check the brake fluid level immediately and add fluid as required. Then check all brake components for fluid leaks.
3. Do not drive the vehicle if leaks are found, the warning light remains on or the brakes do not operate properly. Have it towed to any authorized Hyundai dealer for a brake system inspection and necessary repairs.
Your vehicle is equipped with dual-diago- nal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only a portion of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so. To check bulb operation, check whether the parking brake and brake fluid warning light illuminates when the ignition switch is in the ON position.
WARNING
Driving the vehicle with a warning light on is dangerous. If the brake warning light remains on, have the brakes checked and repaired imme- diately by an authorized Hyundai dealer.
Features of your vehicle
Front fog light indicator (if equipped)
This light comes on when the front fog lights are ON.
Automatic transaxle posi- tion indicator light (if equipped)
This indicator displays which automatic transaxle shift position is selected.
Manual transaxle shift indicator (if equipped)
This indicator informs you which gear is desired while driving to save fuel. For example:
: Indicates that shifting up to the 3rd gear is desired (currently the shift lever is in the 2nd gear).
: Indicates that shifting down to the 3rd gear is desired (currently the shift lever is in the 4th gear).
4 49
Features of your vehicle
Charging system warning
Trunk lid open warning light
Malfunction indicator lamp (MIL) (check engine light)
This warning light indicates a malfunction of either the generator or electrical charging system. If the warning light comes on while the vehicle is in motion: 1. Drive to the nearest safe location. 2. With the engine off, check the genera- tor drive belt for looseness or break- age.
3. If the belt is adjusted properly, a prob- lem exists somewhere in the electrical charging system. Have an authorized Hyundai dealer correct the problem as soon as possible.
This warning light illuminates when the trunk lid is not closed securely with the ignition in any position.
Door ajar warning light
This warning light illuminates when a door is not closed securely with the igni- tion in any position.
Low fuel level warning
This warning light indicates the fuel tank is nearly empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below “E” can cause the engine to misfire and damage the catalytic converter.
This indicator light is part of the Engine Control System which monitors various emission control system components. If this light illuminates while driving, it indi- cates that a potential problem has been detected somewhere in the emission control system. This light will also illuminate when the ignition switch is turned to the ON posi- tion, and will go out in a few seconds after the engine is started. If it illuminates while driving, or does not illuminate when the ignition key is turned to the ON posi- tion, take your vehicle to your nearest authorized Hyundai dealer and have the system checked. Generally, your vehicle will continue to be drivable, but have the system checked by an authorized Hyundai dealer promptly.
50
CAUTION
(cid:129) Prolonged driving with the Emission Control System Malfunction Indicator Light ) illuminated may cause damage to the emission control systems which could effect dri- vability and/or fuel economy.
(cid:129) If the Emission Control System Malfunction Indicator Light ( illuminates, potential catalytic converter damage is possible. This could result in loss of engine power. Have the Engine Control System inspected as soon as pos- sible by an authorized Hyundai dealer.
Engine coolant tempera- ture warning light (if equipped)
WARNING
Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could erupt and cause severe burns. Wait until the engine is cool before removing the radiator cap.
This warning light shows the temperature of the engine coolant when the ignition switch is ON. The warning light illumi- nates if the temperature of the engine coolant is above 248°F (120°C) and the warning light turns off if the temperature of the engine coolant is below 239°F (115°C). If the warning light illuminates, pull over and stop as soon as possible and turn off the engine. Then open the hood and check the coolant level (If your vehicle overheats, refer to “If the engine over- heats” in the Index.) and the water pump drive belt. If you suspect cooling system trouble, have your cooling system checked by a Hyundai dealer as soon as possible.
Features of your vehicle
✽✽ NOTICE If the engine coolant temperature warn- ing light illuminates, it indicates over- heating that may damage the engine.
Low washer fluid level warning indicator (if equipped)
This warning light indicates the washer fluid reservoir is near empty. Refill the washer fluid as soon as possible.
4 51
Features of your vehicle
ESC (Electronic Stability Control) indicator (if equipped)
ESC
The ESC indicator will illuminate when the ignition switch is turned ON, but should go off after approximately 3 sec- onds. When the ESC is on, it monitors the driving conditions and under normal driving conditions, the ESC light will remain off. When a slippery or low trac- tion condition is encountered, the ESC will operate, and the ESC indicator will blink to indicate the ESC is operating.
ESC OFF indicator (if equipped)
ESC OFF
The ESC OFF indicator will illuminate
when the ignition switch is turned ON,
but should go off after approximately 3
seconds. To switch to ESC OFF mode,
press the ESC OFF button. The ESC
OFF indicator will illuminate indicating
the ESC is deactivated.
If this indicator
stays on in the ESC ON mode, the ESC
may have a malfunction. Take your car to
an authorized Hyundai dealer and have
the system checked.
52
Cruise indicator (if equipped)
CRUISE indicator
CRUISE
The indicator light illuminates when the cruise control system is enabled. The cruise indicator light in the instru- ment cluster is illuminated when the cruise control ON/OFF button on the steering wheel is pulled. The indicator light turns off when the cruise control ON/OFF button is pushed again. For more Information about the use of cruise control, refer to section 5, “Cruise control system”.
Cruise SET indicator
SET
The indicator light illuminates when the cruise function switch (COAST/SET or RES/ACCEL) is ON. The cruise SET indicator light in the instrument cluster is illuminated when the cruise control switch (COAST/SET or RES/ACCEL) is pushed. The cruise SET indicator light does not illuminate when the cruise control switch (CANCEL) is pushed or the system is disengaged.
Key reminder warning chime (if equipped) If the driver’s door is opened while the ignition key is left in the ignition switch (ACC or LOCK position), the key reminder warning chime will sound. This is to prevent you from locking your keys in the vehicle. The chime sounds until the key is removed from the ignition switch or the driver’s door is closed.
Electronic power steering (EPS) system warning light
EPS
This indicator light comes on after the ignition key is turned to the ON position and then it will go out with the engine started. This light also comes on if the EPS has a malfunction. If it comes on while driving, have your vehicle inspected by an authorized Hyundai dealer.
Low tire pressure telltale (if equipped)
The low tire pressure telltale comes on for 3 seconds after the ignition switch is turned to the ON position. If the warning light does not come on, or continuously remains on after coming on for about 3 seconds when you turned the ignition switch to the ON position, the Tire Pressure Monitoring System is not working properly. If this occurs, have your vehicle checked by an authorized HYUNDAI dealer as soon as possible. This warning light will also illuminate if one or more of your tires is significantly under-inflated. You should stop and check your tires as soon as possible. If the warning light illuminates while driv- ing, reduce vehicle speed immediately and stop the vehicle. Avoid hard braking and overcorrecting at the steering wheel. Inflate the tires to the proper pressure as indicated on the vehicle’s tire information placard.
WARNING
Air pressure drops about 1 psi for every 10 degrees of air tempera- ture. When checking tire pressure in a warm garage, the low tire pres- sure telltale may illuminate after the vehicle has been parked outside. Inflate the tire pressure to the cor- rect pressure for the outdoor tem- perature.
WARNING - Low tire pres-
sure
low
tire pressure Significantly makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances. Continued driving on tires with low pressure will cause the tires to overheat and fail.
Features of your vehicle
TPMS
TPMS (Tire pressure mon- itoring system) malfunction indicator (if equipped) The TPMS malfunction indicator comes on for 3 seconds after the ignition switch