2004 Hyundai Elantra Owners Manual

WARNING:

Avoid eye injury. DO NOT overstretch. AL- WAYS keep face and body out of recoil path. DO NOT use when strap has visible signs of wear or damage.

HXDFL035
The storage box is located in right side of the luggage compartment floor.

HXDFL1025-1
When loading the objects in the luggage com- partment, hook the four rings located in the luggage compartment floor to attach the lug- gage net as shown illustration. This will prevent the objects from sliding.

CAUTION:

To prevent damage to the goods or the vehicle, care should be taken when carrying fragile or bulky objects in the trunk.

1 FEATURES OF YOUR HYUNDAI

76

CD AUTO CHANGER

STEERING WHEEL TILT LEVER

HORN

B800A01E-GAT (If Installed)

B600A01A-AAT (If Installed)

B610A01Y-AAT

HXD150
The CD Auto Changer is located in the left side of the trunk. This system can store up to 8 CDs. You may select music without changing disks. First, open the CD Auto Changer door, remove the CD "magazine" and insert up to 8 CDs. Then, push the magazine into the CD Auto Changer. The CD may be operated with the passenger compartment audio system con- trols.

To Adjust the Steering Wheel:

HXDFL600

B610A01E Press the pad on the steering wheel to sound the horn.

1. Push the lever downward to unlock. 2. Raise or lower the steering wheel to the

3. After adjustment, securely tighten the lever

desired position.

by pulling it upward.

WARNING:

Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle which may cause serious injury or death.

CRUISE CONTROL

B660A01S-AAT (If Installed)

B660B02E-AAT To Set the Cruise Speed

FEATURES OF YOUR HYUNDAI

77

5. To increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.

WARNING:

To avoid accidental cruise control engage- ment, keep the cruise control main switch off when not using the cruise control.

Main Switch

B660A01E

B660B01E

The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).

1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illumi- nated. This turns the system on.

2. Accelerate to the desired cruising speed

above 25 mph (40 km/h).

3. Push the cruise control switch downward to "SET (COAST)" and release it. If the "SET" (COAST)" switch is selected the "CRUISE" and "SET"(COAST) indicator light in the instrument cluster will be illuminated simulta- neously.

4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.

1 FEATURES OF YOUR HYUNDAI

78

B660C03E-AAT To Cancel the Cruise Speed

B660D01E-AAT To Resume the Preset Speed

B660F01E-AAT To Reset at a Slower Speed

B660C01E

B660D01E

B660B01E

Do one of the following:

o Pull the control switch toward the steering

wheel to "CANCEL" position.

o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "P" or "N" position

(Auto-matic transaxle).

o Decrease the vehicle speed to less than 25

mph (40 km/h).

o Release the main switch.

The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to "RESUME (ACCEL)" position and release it, providing the vehicle speed is above 25 mph (40 km/h).

1. Push the control switch downward to "SET (COAST)" and hold it. The vehicle will decel- erate.

2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.

B660E01E-AAT To Reset at a Faster Speed

1. Push the control switch upward to "RE-

SUME (ACCEL)" position and hold it.

2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.

FEATURES OF YOUR HYUNDAI

79

WARNING:

o Keep the main switch off when not using

the cruise control.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving conditions whenever using the cruise control system.

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch. o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system deacti- vate. This is an indication of normal system operation.

o During normal cruise control operation, when the "SET(COAST)" is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 seconds. This delay is normal.

1 FEATURES OF YOUR HYUNDAI

80

HEATING AND COOLING CONTROL

B710A01E-GAT (If Installed)

B710B01S-AAT CENTER VENTILATOR

The center ventilators are located in the middle of the dashboard. The direction of air flow from the vents in the center of the dashboard is adjustable. To control the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side.

B710C01HP-AAT SIDE VENTILATOR

The side ventilators are located on each side of dashboard. To change the direction of the air flow, move the knob in the center of the vent up- and-down and side-to-side. The side vent knobs control the amount of outside air entering the vehicle through the side vents. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

1. Side Defrost Nozzle 2. Side Ventilator 3. Windshield Defrost Nozzle 4. Center Ventilator

B710A02E-A

HEATING AND VENTILATION

B670A01A-AAT Rotary type (If installed)

B670D01E-AAT Air Flow Control

FEATURES OF YOUR HYUNDAI

81

HXDOM046-A

This model has four controls for the heating and cooling system. They are:

1. Air flow control 2. Air intake control 3. Temperature control 4. Fan speed control

B670C01E-A

Face-Level

HXDFL539-A

This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and De- frost air position. The MAX A/C mode is used to cool the inside of the vehicle faster.

Selecting the "Face" mode will cause air to be discharged through the face level vents.

1 FEATURES OF YOUR HYUNDAI

82

HXDFL540-A

HXDFL541-A

HXDFL543-A

Bi-Level

Floor-Level

Air is discharged through the face vents and the floor vents.

Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle and side ventilator.

Floor-Defrost Level

Air is discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle and side ventilator. If the "Floor-Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be activated.

FEATURES OF YOUR HYUNDAI

83

B670C02E-AAT Air Intake Control

HXDFL542-A

HXDFL544-A

MAX A/C

MAX A/C-Level

Air is discharged through the face level vents. If the "MAX A/C" mode is selected, the A/C will turn on automatically and "Recirculation" mode will be activated.

Defrost-Level

Air is discharged through the windshield de- froster nozzle, side defroster nozzle and side ventilator. If the "Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be ac- tivated.

NOTE: If the "Floor-Defrost" or "Defrost" mode is selected, the air conditioning will not turn off by pushing the A/C button.

B670C02E-A

This is used to select fresh outside air or recirculating inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is in fresh mode.

RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the air intake control is in recirculation mode.

1 FEATURES OF YOUR HYUNDAI

84

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating in "Recirculation" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Re- circulation" mode selected may result in the air within the passenger compart- ment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control will change to "Fresh" mode in floor, floor-defrost and defrost position. This is normal opera- tion.

B670E02A-AAT Temperature Control

B670B02A-AAT Fan Speed Control (Blower Control)

B670E02A-A

B670A01E-A

This control is used to adjust the degree of heating or cooling desired.

This is used to turn the blower fan on or off and to select the fan speed. This blower fan speed, and therefore the vol- ume of air delivered from the system, may be controlled manually by setting the blower con- trol between the "1" and "4" positions.

NOTE: If the blower fan is off, it will set to the fresh mode automatically and be able to select "Fresh"mode or "Recirculation" mode.

HEATING CONTROLS

BI-LEVEL HEATING

VENTILATION

B690A01E-AAT

B700A01E-AAT

B710A01S-AAT

FEATURES OF YOUR HYUNDAI

85

B690A01E-A For normal heating operation, set the air intake control to the fresh air ( ) position and the air flow control to floor ( ) position.

For faster heating, the air intake control should be set in the recirculate ( ) position.

If the windows fog up, move the air flow control to the defrost ( ) position. (The A/C will be on automatically and "Fresh" mode will be acti- vated.)

For maximum heat, move the temperature con- trol to "Warm".

B700A01E-A Your Hyundai is equipped with bi-level heating controls.

o Set the air intake control to fresh air ( )

( ).

o Set the air flow control at the bi-level ( )

o Adjust the fan speed control to the desired

speed.

o Set the temperature control between "Cool"

and "Warm".

position.

position.

speed.

and "Warm".

To operate the ventilation system:

B710A01E-A

o Set the air intake control to "Fresh" mode

o To direct all intake air to the dashboard

vents, set the airflow control to "Face".

o Adjust the fan speed control to the desired

o Set the temperature control between "Cool"

1 FEATURES OF YOUR HYUNDAI

86

B730A01E-AAT Operation Tips

o To keep dust or unpleasant fumes from entering the car through the ventilation sys- tem, temporarily set the air intake control to ( ). Be sure to return the control to ( ) when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable.

o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind- shield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.

o To prevent interior fog on the windshield, set the air intake control to the fresh air ( ) position and fan speed to the desired posi- tion.

B720A01E-AAT

DEFROSTING/DEFOGGING

A Type

B Type

A Type

B Type

FEATURES OF YOUR HYUNDAI

87

B720A02E-A

B720A03E-A

Use the heating/ventilation system to defrost or defog the windshield: To remove interior fog on the windshield; o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

To remove frost or exterior fog on the windshield; o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position. NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs set the air flow control to the face level position ( ) and fan speed control to the low position.

o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".

1 FEATURES OF YOUR HYUNDAI

88

AIR CONDITIONING SYSTEM

B740A01S-AAT Air Conditioning Switch

B740B01S-AAT Air Conditioning Operation Cooling

B740A02E-A

The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

To use the air conditioning to cool the interior:

B740B01E-A

o Set the side vent control to "OFF", to shut off

outside air entry.

o Turn on the fan control switch. o Turn on the air conditioning switch by push- ing in on the switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The tempera- ture may be moderated by moving the con- trol toward "Warm".)

o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the "Recirculation" position on the air intake control.

B740C01S-AAT Dehumidified Heating For dehumidified heating:

o Turn on the fan control switch. o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

o Set the air flow control to "Face". o Adjust the fan control to the desired speed. o For more rapid action, set the fan at one of

the higher speeds.

o Adjust the temperature control to provide the

desired amount of warmth.

B740D01A-AAT Operation Tips

FEATURES OF YOUR HYUNDAI

89

o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.

o When you are using the air conditioning system, keep all windows closed to keep hot air out.

o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning compressor.

o On steep grades, turn the air conditioning off to avoid the possibility of the engine over- heating.

o During winter months or in periods when the air conditioning is not used regularly, run the air conditioning once every month for a few minutes. This will help circulate the lubri- cants and keep your system in peak oper- ating condition.

1 FEATURES OF YOUR HYUNDAI

90

AUTOMATIC HEATING AND COOL- ING CONTROL SYSTEM

B970A01Y-AAT (If lnstalled)

Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperature.

B970B01E-GAT Heating and Cooling Controls

1. Temperature Control Switch 2. Display Window 3. Blower Fan Control Switch 4. Air Flow Control Switch 5. AUTO (Automatic Control) Switch 6. Defroster Switch 7. OFF Switch 8. Air Conditioning Switch 9. Air lntake Control Switch/Air Quality

System Switch (If installed)

10.Rear Window Defroster Switch 11.Ambient Temperature Switch

TYPE A (Without A.Q.S: Air Quality System)

TYPE B (With A.Q.S: Air Quality System)

4 5

6 7

8 9

10 11

HXDOM118

4 5

6 7

8 9

1011

HXDOM119

B970C02E-AAT Automatic Operation

FEATURES OF YOUR HYUNDAI

91

NOTE: If the battery has been discharged or dis- connected, the temperature mode will reset to centigrade degrees. This is a normal condition and you can change the temperature mode from centi- grade to farenheit as follows; Press the TEMP button down 3 seconds or more with the button held down. The display shows that the unit of temperature is adjusted to centigrade or fahrenheit. (°C → → → → → °F or °F →→→→→ °C)

OUTSIDE

TEMP

HXD118D

The FATC (Full Automatic Temperature Con- trol) system automatically controls heating and cooling as follows:

1. Push the "AUTO" button. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and, air conditioner will be controlled automatically.

HXD118A 2. Push the "TEMP" button to set the desired

temperature. The temperature will increase to the maxi- mum 90°F(32°C) by pushing on the " " button. Each push of the button will cause the temperature to increase by 1°F(0.5°C). The temperature will decrease to the mini- mum 62°F(17°C) by pushing on the " " button. Each push of the button will cause the temperature to decrease by 1°F(0.5°C).

Photo sensor

HXDFL280S

NOTE: Never place anything over the sensor which is located on the instrument panel to en- sure better control of the heating and cool- ing system.

1 FEATURES OF YOUR HYUNDAI

92

B995A01Y-GAT AMBIENT TEMPERATURE SWITCH

B980A01Y-AAT MANUAL OPERATION

B980B01Y-AAT Fan Speed Control Switch

The heating and cooling system can be con- trolled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not se- lected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

HXD118I

Pressing the button displays the ambient temperature on the display.

OUTSIDE

TEMP

HXD118C

The fan speed can be set to the desired speed by pressing the appropriate fan speed control button. The higher the fan speed is, the more air is delivered. Pressing the "OFF" button turns off the fan.

B670C01E-AAT Air Intake Control Switch (Without A.Q.S)

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

B980C03E-GAT Air Intake Control Switch (With A.Q.S) (If Installed)

FEATURES OF YOUR HYUNDAI

93

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating system in "Recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Re- circulation" mode selected may result in the air within the passenger compart- ment becoming excessively dry.

o When the ignition switch is turned "ON", the air intake control will change to ( ) mode (regardless of switch position). This is normal operation. The air intake control operates in "AUTO" mode when turning the ignition to the "ON" position if the "AUTO" mode was used before shutting off the engine.

This is used to select fresh outside air or recirculate inside air automatically.

HXD118H

: OFF : ON

Fresh mode :

Air enters the vehicle from the outside and is heated or cooled according to the function selected.

HXD118G

This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is fresh mode.

RECIRCULATION MODE ( ) : The indica- tor light on the button is illuminated when the air intake control is recirculation mode.

1 FEATURES OF YOUR HYUNDAI

94

Recirculation mode :

Air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

Exhaust gas cutoff mode :

Air enters the vehicle from the outside. But if exhaust gas enters the vehicle from the outside, the exhaust gas cutoff mode ( ) is automatically converted to the ( ) mode, to prevent exhaust gas from entering the vehicle.

NOTE: o It should be noted that prolonged opera- tion of the heating system in recircula- tion mode ( ) will give rise to misting of the winds-hield and side windows and the air within the passenger com- partment will become stale. In addition, prolonged use of the air conditioning with the recirculation mode ( ) selec- ted may result in the air within the pas- senger compartment becoming exces- sively dry.

B980E01E-GAT Air Flow Control

o When the ignition switch is turned "ON" the air intake control will change to ( ) mode except for turning "OFF" the igni- tion switch in A.Q.S mode ( ). It is normal operation. The air intake control is operated in "AUTO" mode when turn- ing the ignition to the "ON" position if the "AUTO" mode was used before shut- ting off the engine.

CAUTION:

If the windows fog up with the Recircula- tion or A.Q.S mode selected, set the air intake control to the Fresh air position or A.Q.S control to "OFF".

B980D01Y-AAT Heating and Cooling System Off

Press the "OFF" button to stop the operation of the heating and cooling system.

B980E01E

This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Four symbols are used to represent Face, Bi-Level, Floor and Floor-Defrost air position.

FEATURES OF YOUR HYUNDAI

95

HXDFL539-A

HXDFL540-A

HXDFL541-A

Face-Level

When selecting the "Face" mode, the indicator light will come on, causing air to be discharged through the face level vents.

Bi-Level

When selecting the "Bi-Level" mode, the indica- tor light will come on and the air will be dis- charged through the face vents and the floor vents.

Floor-Level

When selecting the "Floor-Level" mode, the indicator light will come on and the air will be discharged through the floor vents, windshield defrost nozzle, side defroster nozzle and side ventilator.

1 FEATURES OF YOUR HYUNDAI

96

B980F02E-AAT Defrost switch

AIR FILTER (IN FRONT OF BLOWER UNIT)

B760A02E-AAT (If Installed)

Outside air

Inside air

Filter

HXDFL543-A

Floor-Defrost Level

When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defrost vents, the floor vents and side defroster nozzle side ventilator .

Inside air

Blower fan

Evaporator core

HXD118E

Heater core

B760A01E

When the "Defrost" button is pressed, the ( ) mode will be automatically selected and the air will be discharged through the windshield de- frost nozzle, side defroster nozzle and side ventilator. To assist in defrosting, the air condi- tioning will operate if ambient temperature is higher than 38.3°F, and automatically turns off if the ambient temperature drops below 38.3°F.

The air filter is located in front of the blower unit behind the glove box. It operates to decrease pollutants from entering the car and to filter the air.

FEATURES OF YOUR HYUNDAI

97

CAUTION:

o Replace the filter every 12,000 miles (20,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent air filter inspections and changes are re- quired.

o When the air flow rate is decreased, it must be checked at an authorized dealer. o If your vehicle is not equipped with this filter, it can be installed by your dealer. Check with your dealer for details.

1 FEATURES OF YOUR HYUNDAI

98

STEREO SOUND SYSTEM

B750A02A-AAT How Car Audio Works FM reception

Ionosphere

B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality repro- duction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

AM reception

Ionosphere

FM radio station

Mountains

Unobstructed

area

B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequen- cies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

Buildings

Obstructed area

Iron bridges

B750A03L

FM broadcasts are transmitted at high frequen- cies and do not bend to follow the earth's surface. Because of this, FM broadcasts gen- erally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

FEATURES OF YOUR HYUNDAI

99

B750B02Y-AAT Using a cellular phone or a two-way radio

When a cellular phone is used inside the vehicle, noise may be produced from the audio equip- ment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

CAUTION:

When using a communication system such a cellular phone or a radio set inside the vehicle, a separate external antenna must be fitted. When a cellular phone or a radio set is used with an internal antenna alone, it may interfere with the vehicle's electrical system and adversely affect safe operation of the vehicle.

WARNING:

Don't use a cellular phone when you are driving. Stop at a safe place to use a cellular phone.

B750A04L

B750A05L

o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

o Station Swapping - As an FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.

1 FEATURES OF YOUR HYUNDAI 100

CAR AUDIO SYSTEM

H240A01O-GAT STEREO RADIO OPERATION (H240) (If Installed)

5. BAND Selector

3.

TREBLE/FADER Control Knob (TREB/FAD)

6. PRESET Buttons

7. SCAN Button

2. BASS/BALANCE Control Knob

(BASS/BAL)

4. TUNE/SEEK Select Button

1. POWER ON/OFF, VOLUME Control Knob

H240A01O

FEATURES OF YOUR HYUNDAI

101

3. TREB (Treble Control) Knob

Press to pop the knob out and turn to the left or right for the desired treble tone.

FAD (Fader Control) Knob

Pull the treble control knob further out. Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).

4. TUNE (Manual) Select Button

Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection)

Press the TUNE select button 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second, releasing will automatically tune to the next lower frequency.

5. BAND Selector

FM/AM

Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is displayed on LCD.

6. PRESET STATION SELECT Button

Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit on this unit.

H240B03O-AAT 1. POWER ON-OFF Control Knob

The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the tape direction indicator in the tape mode. To switch the power off, press the knob again.

VOLUME Control

Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

2. BASS Control Knob

Press to pop the knob out and turn to the left or right for the desired bass tone.

BAL (Balance Control) Knob

Pull the bass control knob further out. Turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).

1 FEATURES OF YOUR HYUNDAI 102

HOW TO PRESET STATIONS

7. SCAN Button

Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.

o Press band selector to set the band for AM,

FM, or FM2.

o Select the desired station to be stored by

seek or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with a beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

H240C01O-GAT CASSETTE TAPE PLAYER OPERATION (H240) (If Installed)

3. TAPE PROGRAM Button

6. TAPE SLOT

2. AUTO MUSIC SELECT Button

4. EJECT Button

FEATURES OF YOUR HYUNDAI

103

1.

FF/REW Button

5. DOLBY SELECT Button

H240A01O

1 FEATURES OF YOUR HYUNDAI 104

H240A02O-GAT 1. FF/REW Button o The FF (fast forward tape winding) starts when the button is pressed during the PLAY or REW.

o The play starts when the button is press-

ed again during the FF.

o The REW (rewinding) starts when the bu-

tton is pressed during the PLAY or FF.

o The play starts when the button is press-

ed again during the REW.

NOTE: When tape operation is abnormal or ER8
fault code is displayed, press the eject button more than 5 seconds to reset the deck function.

4. EJECT Button

o When the EJECT button is pressed with the

cassette loaded, the cassette is ejected.

o When the EJECT button is pressed during

the FF/REW, the cassette is ejected.

2. AUTO MUSIC SELECT Button

Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4 sec. gap) can be identified by the AUTO MUSIC SELECT button.

5. DOLBY SELECT Button

If you get background noise during PLAY, you can reduce this considerably by merely press- ing DOLBY SELECT button. If you want to release, press the button again.

o Pressing the button will play the beginn-

ing of the next music segment.

o Pressing the button will start replay at the beginning of the music just listened to.

3. TAPE PROGRAM Button

This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.

H260A01O-AAT STEREO RADIO OPERATION (H260) (If installed)

3. BASS/TREBLE Control Knob

4. SCAN Button

6. BAND Selector

FEATURES OF YOUR HYUNDAI

105

7. PRESET Button

5. TUNE/SEEK Select Button

1. POWER ON-OFF/VOLUME/BALANCE Control Knob

2. FADER Control Knob

H260A01O

1 FEATURES OF YOUR HYUNDAI 106

H260B02E-AAT 1. POWER ON-OFF Control Knob

The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the CD track indicator in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the knob again.

VOLUME Control

Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

BALANCE Control

Pull and turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

2. FAD (Fader Control) Knob

5. TUNE (Manual) Select Button

Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).

3. BASS Control Knob

Press to pop the knob out and turn to the left or right for the desired bass tone.

TREB (Treble Control) Knob

Pull the bass control knob further out. Turn to the left or right for the desired treble tone.

Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection) Press the TUNE select button for 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second, releasing will automatically tune to the next lower frequency.

4. SCAN Button

6. BAND Selector

When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.

Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is displayed on LCD.

FM/AM

7. PRESET STATION SELECT Button

Six (6) stations for AM, FM or FM2 respectively can be preset in the electronic memory circuit on this unit.

HOW TO PRESET STATIONS

Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To program the stations, follow these steps:

FEATURES OF YOUR HYUNDAI

107

o Press band selector to set the band for AM,

FM or FM2.

o Select the desired station to be stored by

seek, scan or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

1 FEATURES OF YOUR HYUNDAI 108

H260B01O-AAT COMPACT DISC PLAYER OPERATION (H260) (If installed)

4. SCAN Button

1.Playing CD

3. TRACK UP/DOWN

6. EJECT Button

2. FF/REW Button

5. REPEAT Button

H260A01O

B260D03O-AAT 1. Playing CD

o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during

radio operation.

o When a disc is in the CD deck, if you press the play button, the CD player will begin playing even if the radio is being used.

o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.

2. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press once to skip forward to the beginn- ing of the next track. Press once to skip back to the beginning of the track.

4. SCAN Button

o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

5. REPEAT Button o To repeat the track you are listening to, press the RPT button. To cancel , press again.

o If you do not release RPT operation, when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

6. EJECT Button

When the EJECT button is pressed with the CD loaded, the CD is ejected.

FEATURES OF YOUR HYUNDAI

109

NOTE: o If the CD does not operate properly or if the ER2 fault code is displayed, use one of two methods to reset the CD deck function. - Remove the audio fuse for 5 minutes.

Then, reinstall the audio fuse.

- Disconnect the negative terminal of

the battery and wait 5 minutes. Then reconnect the negative battery terminal.

o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle's air conditioning or heating system.

o When replacing the fuse, replace it with

a fuse having the correct capacity.

o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.

o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

1 FEATURES OF YOUR HYUNDAI 110

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

o Do not expose this equipment (includ- ing the speakers) to water or excessive moisture.

CAUTION:

Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.

B260E01E-AAT CD AUTO CHANGER (H260) (If installed)

6. SCAN Button

1. CD Select Button

3. TRACK UP/DOWN

FEATURES OF YOUR HYUNDAI

111

4. FF/REW Button

5. REPEAT Button

2. DISC Select Button

H260A01O

1 FEATURES OF YOUR HYUNDAI 112

B260F02E-AAT The CD auto changer is located in the left side of the trunk.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto changer. 2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto changer

and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either the "ON" or "ACC" position.

1. CD Select Button

When the CD changer magazine contains discs, press the "CD" button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.

2. DISC Select Button

To select the CD you want, push to change the disc number.

TUNE DISC

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

5. REPEAT

o To repeat the track you are listening to, press the RPT button. To cancel , press again.

o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.

6. SCAN Button o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

NOTE: o When replacing the fuse, replace it with

a fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

CAUTION:

Do not insert warped or poor quality discs into the CD changer as damage to the unit may occur.

H290A01O-AAT STEREO RADIO OPERATION (H290) (If installed)

1. POWER ON/OFF VOLUME Control Knob

8. SCAN Button

FEATURES OF YOUR HYUNDAI

113

7. EQUALIZER Button

6. BAND Select Button

5. PRESET Buttons

4. TUNE/SEEK Select Button

3. TREBLE/FAD Konb

2. BASS/BALANCE Control Knob

H290A01O

1 FEATURES OF YOUR HYUNDAI 114

H290B03E-GAT 1. POWER ON-OFF Control Knob

The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the button to switch the power on. The display shows the radio frequency in the radio mode, the tape direction indicator in the tape mode or CD track in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the button again.

VOLUME Control

Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

2. BASS/BALANCE Control Knob BASS Control Knob

Press to pop the knob out. To increase the bass, rotate the knob clockwise, while to decrease the bass, rotate the knob counterclockwise.

BALANCE Control knob

Pull the Bass control knob out further. Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).

3. TREBLE/FAD Knob TREBLE Control Knob

Press to pop the knob out and turn to the left or right for the desired treble tone.

FAD (Fader Control) Knob

Pull the Treble control knob out further. Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be empha- sized (front speaker sound will be attenuated).

4. TUNE (Manual) Select Button

Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection)

Press the TUNE select button for 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second and releasing will automatically tune to the next lower fre- quency.

5. PRESET STATION Select Buttons

Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit.

HOW TO PRESET STATIONS

6. BAND Selector

FEATURES OF YOUR HYUNDAI

115

Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

o Press band selector to set the band for AM,

FM or FM2.

o Select the desired station to be stored by

seek or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with a beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM station per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

FM/AM

Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is shown on the display.

7. EQUALIZER Button

Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;

CLASSIC → JAZZ → ROCK → DEFEAT

8. SCAN Button

When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.

1 FEATURES OF YOUR HYUNDAI 116

H290C01O-AAT CASSETTE TAPE PLAYER OPERATION (H290) (If installed)

4. TAPE EJECT Button

5. EQUALIZER

Button

2. AUTO MUSIC Select Button

1. FF/REW Button

6. DOLBY Button

3. TAPE PROGRAM Button

H290A01O

FEATURES OF YOUR HYUNDAI

117

3. TAPE PROGRAM Button

6. DOLBY Button

This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.

4. TAPE EJECT button

If you get background noise during tape PLAY, you can reduce this considerably by merely pressing the DOLBY button. If you want to cancel the DOLBY feature, press the button again.

o When the button is pressed with a cass-

ette loaded, the cassette will eject.

o When the button is pressed during FF/

REW mode, the cassette will eject.

5. EQ Button Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;

CLASSIC → JAZZ → ROCK → DEFEAT

H290D01O-GAT 1. FF/REW Button

o Fast forward tape winding starts when the FF ( ) button is pressed during PLAY or REW mode.

o Tape PLAY starts when the FF ( ) button

is pressed again during FF mode.

o Tape rewinding starts when the REW ( ) button is pressed during PLAY or FF mode. o Tape PLAY starts when the REW ( ) button

pressed again during REW mode.

2. AUTO MUSIC Select Button

Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4
sec. gap) can be identified by the AUTO MUSIC Select button.

o Pressing the button will play the begin-

ning of the next music segment.

o Pressing the button will start replay at the beginning of the music just listened to.

1 FEATURES OF YOUR HYUNDAI 118

H290E01O-AAT COMPACT DISC PLAYER OPERATION (H290) (If installed)

6. CD EJELT Button

7. SCAN Button

5. EQUALIZER Button

3. TRACK UP/DOWN

2. FF/REW Button

4. REPEAT

1. CD Select Button

H290A01O

H290F02O-GAT 1. CD Select Button

o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during

radio operation or cassette tape playing.

o When a disc is in the CD deck, if you press the CD button the CD player will begin playing even if the radio or cassette player is being used.

o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.

2. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press button once to skip forward to the beginning of the next track. Press button once to skip back to the beginning of the track.

4. REPEAT

7. SCAN Button

FEATURES OF YOUR HYUNDAI

119

o To repeat the track you are currently listen- ing to, press the RPT button. To cancel, press again.

o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.

5. EQUALIZER Button

Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;

CLASSIC → JAZZ → ROCK → DEFEAT

6. CD EJECT Button

When the button is pressed with a CD loaded, the CD will eject.

o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec. When you have reached the desired track.

NOTE: o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle's air conditioning or heating system.

o When replacing the fuse, replace it with

a fuse having the correct capacity.

o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.

o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

1 FEATURES OF YOUR HYUNDAI 120

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

o Do not expose this equipment (includ- ing the speakers and tape) to water or excessive moisture.

CAUTION:

Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.

H290G01E-AAT CD AUTO CHANGER (H290) (If installed)

FEATURES OF YOUR HYUNDAI

121

6. SCAN Button

7. EQ Button

3. TRACK UP/DOWN

4. FF/REW Button

5. REPEAT

2.DISC Select Button

1. CD CHANGER Select Button

H290A01O

1 FEATURES OF YOUR HYUNDAI 122

B290H02E-GAT The CD auto changer is located in the left side of the trunk.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto changer. 2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto changer

and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either "ON" or "ACC" position.

1. CD CHANGER Select Button

When the CD changer magazine contains discs, press the "CD/CDC" button and the CD changer can be used even if the radio or cassette player is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.

2. DISC Select Button

To select the CD you want, push to change the disc number.

TUNE DISC

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

5. REPEAT

o To repeat the track you are currently listen- ing to, press the RPT button. To cancel, press again.

o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.

6. SCAN Button o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec. When you have reached the desired track.

7. EQ Button Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;

CLASSIC → JAZZ → ROCK → DEFEAT

NOTE: o When replacing the fuse, replace it with

a fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

!

CAUTION:

Do not insert warped or poor quality discs into the CD changer as damage to the unit may occur.

FEATURES OF YOUR HYUNDAI