2010 Honda Ridgeline Owners Manual

61

2010 Ridgeline09/07/18 14:08:05 31SJC640_067

Instrument Panel Indicators

The instrument panel has many indicators to give you important information about your vehicle.

Seat Belt Reminder Indicator

This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.

If you turn the ignition switch to the ON (II) position before fastening your seat belts, the beeper sounds, and the indicator flashes. If you do not fasten your seat belts before the beeper stops, the indicator stops flashing but remains on.

62

If your front passenger does not fasten their seat belt, the indicator comes on about 6 seconds after the ignition switch is turned to the ON (II) position.

If either of you do not fasten your seat belt while driving, the beeper will sound and the indicator will flash again at regular intervals. For more information, see page

20

Onmodelswithnavigationsystem You will also see a ‘‘FASTEN SEAT BELT’’ or ‘‘FASTEN PASSENGER SEAT BELT’’ message on the multi- ). information display (see page

90

For more information, see page

.20

2010 Ridgeline09/07/18 14:08:17 31SJC640_068

Instrument Panel Indicators

Malfunction Indicator Lamp

For more information, see page

375

Onmodelswithnavigationsystem You will also see a ‘‘CHECK EMISSION SYSTEM’’ message on the multi-information display (see page page

). For more information, see

90
375

Low Oil Pressure Indicator

The engine can be severely damaged if this indicator flashes or stays on when the engine is running. For more information, see page 374

Charging System Indicator

If this indicator comes on when the engine is running, the battery is not being charged. For more information, see page

374

Onmodelswithnavigationsystem You will also see a ‘‘CHECK ENGINE OIL LEVEL’’ message on the multi-information display (see page

91

).

Onmodelswithnavigationsystem You will also see a ‘‘CHECK CHARGING SYSTEM’’ message on the multi-information display (see page

90

).

63

2010 RidgelineOnmodelswithnavigationsystem You will also see a ‘‘CHECK AIRBAG SYSTEM’’ message on the multi-information display (see page 90

).

09/07/18 14:08:27 31SJC640_069

Instrument Panel Indicators

Supplemental Restraint System Indicator

This indicator comes on for several seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag automatic cutoff system, side curtain airbags, rollover sensor, automatic seat belt tensioners, driver’s seat position sensor, or the front passenger’s weight sensors. For more information, see page 30

64

U.S.

Canada

Side Airbag Off Indicator

This indicator comes on for several seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page 31

Onmodelswithnavigationsystem You will also see a ‘‘PASSENGER SIDE AIRBAG OFF’’ message on the multi-information display (see page 90

).

2010 Ridgeline09/07/18 14:08:36 31SJC640_070

Instrument Panel Indicators

U.S.

Canada

Parking Brake and Brake System Indicator

This indicator has two functions:

1.

It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. A beeper sounds if you drive with the parking brake not fully released. Driving with the parking brake not fully released can damage the brakes and tires.

Onmodelswithnavigationsystem You will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page 90

).

2.

If it stays on after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page

376

Onmodelswithnavigationsystem You will also see a ‘‘BRAKE FLUID LOW’’ or ‘‘CHECK BRAKE SYSTEM’’ message on the multi- information display (see page 90

).

65

2010 Ridgeline09/07/18 14:08:47 31SJC640_071

Instrument Panel Indicators

Anti-lock Brake System (ABS) Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With the indicator on, your vehicle still has normal braking ability but no anti- lock brakes. For more information, see page

289

Onmodelswithnavigationsystem You will also see a ‘‘CHECK ABS SYSTEM’’ message on the multi- information display (see page 91

).

66

Immobilizer System Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It will go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink and the engine will not start (see page

101

).

This indicator also blinks several times when you turn the ignition switch from the ON (II) position to the ACCESSORY (I) or LOCK (0) position.

Turn Signal and Hazard Warning Indicators

The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages ). and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.

338

340

When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.

2010 Ridgeline09/07/18 14:09:02 31SJC640_072

Daytime Running Lights Indicator

If this indicator comes on when the ignition switch is turned to the ON (II) position and the parking brake is released, it means there is a problem with a circuit. Have your vehicle checked by your dealer.

Onmodelswithnavigationsystem If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light circuit. Take your vehicle to a dealer to have it checked.

Instrument Panel Indicators

High Beam Indicator

Washer Level Indicator

This indicator comes on with the high beam headlights. For more information, see page

95

Cruise Main Indicator

This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page

210

).

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page 210
cruise control.

for information on operating the

This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page

330

).

Onmodelswithnavigationsystem You will see a ‘‘WASHER FLUID LOW’’ message on the multi- information display (see page

91

).

67

2010 Ridgeline09/07/18 14:09:12 31SJC640_073

Instrument Panel Indicators

Low Fuel Indicator

LOW FUEL INDICATOR

This indicator comes on as a reminder that you must refuel soon.

When the indicator comes on, there are about 3.3 U.S. gal (12.5 ) of fuel remaining in the tank.

When the needle reaches E, there is a very small amount of fuel in the tank.

68

Onmodelswithnavigationsystem You will also see a ‘‘FUEL LOW’’ message on the multi-information display.

Security System Indicator OnRTS,RTLmodels,andCanadian EX-Lmodels

SECURITY SYSTEM INDICATOR

This indicator comes on when the security system is set. See page 208
for more information on the security system.

2010 Ridgeline09/07/18 14:09:20 31SJC640_074

Lights On Indicator

This indicator reminds you that the exterior lights are on. It comes on when you turn the headlight control dial to either the

or

position.

If you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the headlight control dial, this indicator remains on. A reminder chime will also sound when you open the driver’s door.

A/T Temperature Indicator

This indicator monitors the temperature of the automatic transmission fluid. It should come on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it means the transmission fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Onmodelswithnavigationsystem You will also see an ‘‘A/T TEMP HIGH’’ message on the multi- information display (see page

).91

Instrument Panel Indicators

Continuing to drive with the A/T temperature indicator on may cause serious damage to the transmission.

69

2010 Ridgeline09/07/18 14:09:30 31SJC640_075

Instrument Panel Indicators

VTM-4 Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem in the 4WD system. Take the vehicle to your dealer to have it checked.

If the indicator blinks while driving, the VTM-4 fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Continuing to drive with the VTM-4
indicator blinking may cause serious damage to the system.

70

Onmodelswithnavigationsystem You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display (see page 91

).

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page for more information on the 291
VSA system.

2010 Ridgeline09/07/18 14:09:42 31SJC640_076

VSA Activation Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page

291

This indicator has three functions:

1.

2.

3.

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

291

).

It comes on along with the VSA system indicator if there is a problem with the VSA system.

Onmodelswithnavigationsystem You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- 91
information display (see page

).

Instrument Panel Indicators

Maintenance Minder Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page 313
maintenance minder.

for more information on the

This indicator goes off when your dealer resets it after completing the required maintenance service.

71

2010 Ridgeline09/07/18 14:09:55 31SJC640_077

Instrument Panel Indicators

Low Tire Pressure Indicator

Onmodelswithoutnavigationsystem This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

72

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure on the tire pressure monitor, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page 278

for more information.

). Refer to page

383

361

Low Tire Pressure/ TPMS Indicator

Onmodelswithnavigationsystem This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. This indicator has two functions:

1.

If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multi-information display (see page

91

).

Check the tire pressure monitor on the multi-information display and determine the cause (see page 282

).

2010 Ridgeline09/07/18 14:10:03 31SJC640_078

If this happens, pull to the side of the road when it is safe, check which tire has lost pressure on the multi- information display, and determine the cause. If it is because of a flat tire, have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service. For more information, see page 383

2.

If this indicator begins to flash, there is a problem with the tire pressure monitoring system (TPMS). You will also see a ‘‘CHECK TPMS SYSTEM’’ message on the multi-information display. The indicator continues to flash for a while (approximately 1
minute), then stays on. If this happens, have your dealer check the system as soon as possible. For more information, see page 284

Instrument Panel Indicators

Tire Pressure Monitoring System (TPMS) Indicator

Onmodelswithoutnavigationsystem This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator and the tire pressure monitor will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

73

2010 RidgelineIf you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the bed lights, this indicator will remain on, and then go off after 20 minutes. See page

for more information.

144

09/07/18 14:10:13 31SJC640_079

Instrument Panel Indicators

Message Indicator

Bed Lights On Indicator

This indicator reminds you that the bed lights are on. With the shift lever in the Park position, they come on when you push the light switch on the dashboard, swing open the tailgate, or open the In-Bed Trunk.

Onmodelswithnavigationsystem This indicator comes on when there is a system message on the multi- information display. Press the INFO button on the dashboard (see page 82
) to see the message (see page ). 90

Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.

74

2010 Ridgeline09/07/18 14:10:23 31SJC640_080

In-Bed Trunk Open Indicator

This indicator reminds you that the In-Bed Trunk is open. If you do not close it, the indicator stays on for about 3 minutes. See page for more information.

116

Door and Tailgate Open Indicator

This indicator comes on if any door or the tailgate is not closed tightly.

Instrument Panel Indicators

Back Window Open Indicator

This indicator reminds you that the back window is not completely closed when you turn the ignition switch from the ON (II) position to the ACCESSORY (I) or LOCK (0) position. With the ignition switch in the ACCESSORY (I) position, it goes off after about 30 seconds. With the ignition switch in the LOCK (0) position, it goes off after about 3
minutes.

If you remove the ignition key, turn off the lights, and open the driver’s door without closing the back window, you will hear five beeps and see the indicator blink. If you do not close the back window before the beeper stops, the indicator stops blinking but remains on. It will go off after about 3 minutes. See page 129

for more information.

75

2010 Ridgeline09/07/18 14:10:35 31SJC640_081

Gauges

On models without navigation system

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

SELECT BUTTON TRIP/RESET BUTTON

INFORMATION DISPLAY

FUEL GAUGE

On models with navigation system

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

INFO (

▲

) BUTTON

SEL/RESET BUTTON

INFO (

▼

) BUTTON

MULTI-INFORMATION DISPLAY

FUEL GAUGE

U.S. model is shown.

76

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. For instructions and precautions on checking the engine’s cooling system, see page

372

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

2010 Ridgeline09/07/18 14:10:43 31SJC640_082

Information Display Onmodelswithoutnavigationsystem The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), instant fuel economy, average fuel economy, range (estimated distance), and maintenance item code(s).

Gauges

SELECT BUTTON

Onmodelswithnavigationsystem For information about the multi- information display, see page .82

TRIP/RESET BUTTON

With the ignition switch in the ON (II) position, the information display changes as shown on thenext page each time you press the SELECT button or TRIP/RESET button.

When you turn the ignition switch to the ON (II) position, your last selection display.

CONTINUED

77

2010 Ridgeline09/07/18 14:10:51 31SJC640_083

Gauges

INFORMATION DISPLAY

OUTSIDE TEMPERATURE INDICATOR

ODOMETER

ODOMETER

SELECT button TRIP/RESET button

TRIP METER A AVERAGE FUEL ECONOMY A

TRIP METER B AVERAGE FUEL ECONOMY B

INSTANT FUEL ECONOMY

TRIP METER A RANGE

INSTANT FUEL ECONOMY

TRIP METER B RANGE

TRIP METER A

TRIP METER B

ENGINE OIL LIFE

U.S. model is shown.

78

2010 Ridgeline09/07/18 14:11:05 31SJC640_084

Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

TripMeter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the TRIP/ RESET button repeatedly. Each trip meter works independently, so you can keep track of two different distances. To reset a trip meter, display it, and then press and hold the TRIP/RESET button until the number resets to ‘‘0.0’’.

Both trip meters will reset if the vehicle’s battery goes dead or is disconnected.

OutsideTemperatureIndicator ExceptRTmodels This shows the outside temperature in Fahrenheit (U.S. models), or in Celsius (Canadian models).

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

In certain weather conditions, temperature readings near freezing

Gauges

(32°F, 0°C) could mean that ice is forming on the road surface.

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

The temperature must be

NOTE: stabilized before doing this procedure.

To adjust the outside temperature indicator, press and hold the TRIP/ RESET button for 10 seconds. The following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5, 4, − − − − − −

− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

2, 2,

3, 3,

5,

When the temperature reaches the desired value, release the TRIP/ RESET button. You should see the new outside temperature displayed.

CONTINUED

79

2010 Ridgeline09/07/18 14:11:18 31SJC640_085

Gauges

TirePressureMonitor

TIRE PRESSURE MONITOR

The appropriate tire indicator will come on along with the low tire pressure indicator if a tire is significantly underinflated or has Low suddenly lost pressure. See Tire Pressure Indicator do if this indicator comes on.

for what to

Onmodelswithnavigationsystem This indicator is displayed as the system message on the multi- information display (see page

282

).

80

Range(EstimatedDistance) This display shows the estimated distance you can travel on the fuel remaining in the tank.

This distance is estimated from the fuel economy you have achieved over the last few miles (kilometers), so it will vary with changes in speed, traffic condition, etc.

InstantFuelEconomy This display shows the instant fuel economy you are getting.

It shows the number of mpg (U.S.) or l/100 km (Canada).

AverageFuelEconomy When either of the trip meters (trip A or B) is displayed, your vehicle’s average fuel economy since you last reset that trip meter can be shown on the information display (mpg on U.S. models and l/100 km on Canadian models). This number is updated once per 10 seconds. To see the average fuel economy, press and release the TRIP/RESET button repeatedly.

The average fuel economy will be reset when you reset the trip meter, or if the vehicle’s battery goes dead or is disconnected.

2010 Ridgeline09/07/18 14:11:26 31SJC640_086

Gauges

MaintenanceMinder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

313

for

CheckFuelCapMessage Your vehicle’s onboard diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘CHECK FUEL CAP’’ message appears on the information display.

Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another display, press the SELECT button or TRIP/RESET button.

The ‘‘CHECK FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.

If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page

375

81

2010 Ridgeline09/07/18 14:11:35 31SJC640_087

Multi-Information Display

Onmodelswithnavigationsystem The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.

When you open the driver’s door, a ‘‘Welcome’’ message is shown on the multi-information display.

82

INFO (

▲

) BUTTON

With the ignition switch in the ON (II) position, the multi-information display changes as shown on the next page each time you press the INFO ( / ) button or the SEL/ RESET button.

▲ ▼

SEL/ RESET BUTTON

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

INFO (

▼

) BUTTON

To change the display, press the INFO ( / ) button on the dashboard repeatedly until the main menu appears (see page

▲ ▼

83

).

In the multi-information display, the system message is also displayed (see page

90

).

2010 Ridgeline09/07/18 14:11:41 31SJC640_088

Multi-Information Display

(See page 84)

Trip Computer (See page 87)

Tire Pressure for each tire (See page 86)

Go to HandsFreeLink Menu (See page 86)

Go to Language Selection Menu (See page 92)

U.S. model is shown.

▲ ▼

INFO ( ) button SEL/RESET button

83

2010 Ridgeline09/07/18 14:11:50 31SJC640_089

Multi-Information Display

Odometer

Trip Meter

When you reset Trip A, AVERAGE FUEL A, AVERAGE SPEED A, and ELAPSED TIME A are reset at the same time. When you reset Trip B, AVERAGE FUEL B, AVERAGE SPEED B, and ELAPSED TIME B are reset.

ODOMETER U.S. model is shown.

The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

U.S. model is shown.

TRIP METER

This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.

To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’

84

2010 Ridgeline09/07/18 14:12:01 31SJC640_090

Outside Temperature

OUTSIDE TEMPERATURE

U.S. model is shown.

This shows the outside temperature in Fahrenheit (U.S. models), or in Celsius (Canadian models).

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

Multi-Information Display

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

The temperature must be

NOTE: stabilized before doing this procedure.

To adjust the outside temperature indicator, press and hold the SEL/ RESET button for 10 seconds. The following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5, 4, − − − − − −

− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

2, 2,

3, 3,

5,

When the temperature reaches the desired value, release the SEL/ RESET button. You should see the new outside temperature displayed.

85

2010 Ridgeline09/07/18 14:12:11 31SJC640_091

Multi-Information Display

Engine Oil Life

Tire Pressure Monitor

Bluetooth

HandsFreeLink

U.S.

Canada

ENGINE OIL LIFE

This shows the remaining life of the engine oil. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions and accumulated engine revolutions. For more information, see page

313

86

When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page

282

You can receive or make phone calls from your cell phone through your HandsFreeLink vehicle’s (HFL) system without touching your cell phone.

Bluetooth

2010 Ridgeline09/07/18 14:12:19 31SJC640_092

Multi-Information Display

To use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page for instructions on how to link 221
your cell phone to HFL and how to receive or make phone calls, or visit the handsfreelink.com website. In Canada, visit (888) 9-HONDA-9.

www.honda.ca

, or call 1-

Trip Computer

Average Fuel Economy/Range

Average Vehicle Speed/Elapsed Time

Instantaneous Fuel Economy

U.S. model is shown.

▲ ▼

INFO ( ) button SEL/RESET button

CONTINUED

87

2010 Ridgeline09/07/18 14:12:33 31SJC640_093

Multi-Information Display

Along with the trip meter, the trip computer calculates these values:

Average Fuel Economy Range Average Vehicle Speed Elapsed Time Instantaneous fuel economy

88

ELAPSEDTIMEA/B This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset.

INSTANTFUELMPG(U.S. models)/INSTANTFUELL/100km (Canadianmodels) This shows your instant fuel economy.

AVERAGEFUELA/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset Trip A or Trip B.

RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles (U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.

AVERAGESPEEDA/B This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.

2010 Ridgeline09/07/18 14:12:42 31SJC640_094

System Messages

SYSTEM MESSAGE INDICATOR

If there is a problem with your vehicle, for example the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.

The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.

You will also hear a beep when the system message comes on for the first time.

Multi-Information Display

When there are several messages to be shown, the system switches the messages every 5 seconds. The message is shown until you push the INFO ( ) button. To see the message again, press the INFO ( after the display disappears.

) button, 5 seconds

▲ ▼

▲ ▼

or

or

Here is a list of messages shown on the multi-information display:

CONTINUED

89

2010 Ridgeline09/07/18 14:12:58 31SJC640_095

Multi-Information Display

U.S.

Canada

See page

132

See page

376

See page

376

See page

374

See page

375

U.S.

Canada

U.S.

Canada

See page

11

See page

20

See page

20

See page

30

See page

31

U.S.

Canada

90

2010 Ridgeline09/07/18 14:13:11 31SJC640_096

Multi-Information Display

See page

374

See page

289

See page

291

See page

281

See page

282

See page

69

See page

271

See page

330

See page

68

See page

97

See page

319

See page

250

91

2010 Ridgeline09/07/18 14:13:21 31SJC640_097

Multi-Information Display

Language Selection

There are three language selections you can make: English, Spanish, and French. To choose the language you want, follow these instructions:

Press and release the INFO ( / ) ▲ ▼ button repeatedly to select the ‘‘LANGUAGE SELECTION’’ display.

Press the SEL/RESET button to see the selections.

Select the desired language by pressing the SEL/RESET button, then enter your selection by pressing and holding the SEL/RESET button.

When your selection is successfully completed, the display returns to the ‘‘LANGUAGE SELECTION’’ display.

92

2010 Ridgeline09/07/18 14:13:32 31SJC640_098

INSTRUMENT PANEL BRIGHTNESS (P.98) MOONROOF SWITCH ＊ (P.131) MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.94)

REMOTE AUDIO CONTROLS ＊ (P.203) HEADLIGHT CONTROL DIAL (P.95)

FOG LIGHTS (P.97)

＊

Controls Near the Steering Wheel

TRIP/RESET BUTTON ＊ (P.76)

SELECT BUTTON ＊

(P.76)

SHIFT LEVER (P.271) VTM-4 LOCK (P.276)

▲

) BUTTON ＊

INFO ( (P.76) SEL/RESET BUTTON ＊ (P.76) INFO ( (P.76) PASSENGER AIRBAG OFF INDICATOR

)BUTTON

(P.31)

▼

＊

HAZARD WARNING BUTTON (P.99) CRUISE CONTROLS (P.210) INTERIOR LIGHT CONTROL SWITCH

(P.142)

SEAT HEATERS ＊ (P.126)

HORN ＊

STEERING WHEEL ADJUSTMENT

(P.99)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH

(P.292)

BED LIGHT SWITCH (P.144)

VOICE CONTROL BUTTONS ＊

Vehicle with navigation system is shown.

BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS ＊

(P.221)

＊ ＊ ＊ ＊ ＊

1 : 2 : 3 : 4 : 5 :

To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual. On models with navigation system. On models without navigation system.

93

2010 Ridgeline09/07/18 14:13:44 31SJC640_099

Multi-Control Lever

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washers Turn signal High beams Flash high beams

94

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

MIST:

The wipers run at high speed until you release the lever.

Windshield Washer:

Push the button on the end of the multi-control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.

The multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.

To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.

OFF:

The wipers are not activated.

INT:

The length of the wiper interval is varied automatically according to the vehicle’s speed.

Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).

2010 Ridgeline09/07/18 14:13:55 31SJC640_100

AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to the ON (II) position. The heater turns off automatically when the outside temperature is above freezing.

This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.

Multi-Control Lever, Headlights

Headlight Control Dial

−

Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.

−

High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

67

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

1. 2. 3.

OFF Parking and indicator lights Headlights

CONTINUED

95