2006 Honda Ridgeline Owners Manual

On Canadian models, this indicator comes on with reduced brightness when the daytime running lights (DRL) are on (see page

75

).

Washer Level Indicator

This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page

240

).

LOW FUEL INDICATOR

This indicator is located in the fuel gauge. It comes on as a reminder that you must refuel soon.

When the indicator comes on, there is about 3.30 U.S. gal (12.5 ) of fuel remaining in the tank before the needle reaches E. There is a small reserve of fuel remaining in the tank when the needle does reach E.

Main MenuTable of Contentsst０４／１２／０３　１６：２５：５８　３１ＳＪＣ６００　００６８　

Lights On Indicator

This indicator reminds you that the exterior lights are on. It comes on when you turn the headlight control dial to either the

or

position.

If you turn the ignition switch to ACCESSORY (I) or LOCK (0) without turning off the headlight control dial, this indicator remains on. A reminder chime will also sound when you open the driver’s door.

A/T Temperature Indicator

This indicator monitors the temperature of the automatic transmission fluid. It should come on for a few seconds when you turn the ignition switch to ON (II). If it comes on while driving, it means the transmission fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Continuing to drive with the A/T temperature indicator on may cause serious damage to the transmission.

Instrument Panel Indicators

VTM-4 Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II). If it comes on at any other time, there is a problem in the 4WD system. Take the vehicle to your dealer to have it checked.

If the indicator blinks while driving, the VTM-4 fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Continuing to drive with the VTM-4
indicator blinking may cause serious damage to the system.

63

Main MenuTable of Contentsst０４／１２／０３　１６：２６：１１　３１ＳＪＣ６００　００６９　

VSA Activation Indicator

This indicator has three functions:

Itcomesonasareminderthatyou have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

205

).

Maintenance Minder Indicator

This indicator reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page more information on the maintenance minder.

225

for

It comes on along with the VSA system indicator if there is a problem with the VSA system.

This indicator goes off when your dealer resets it after completing the required maintenance service.

1.

2.

3.

This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II). For more information, see page

205

Instrument Panel Indicators

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II).

Ifitcomesonandstaysonatany other time, or if it does not come on when you turn the ignition switch to ON (II), there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page for more information on the VSA system.

205

64

Main MenuTable of Contentsst０４／１２／０３　１６：２６：２３　３１ＳＪＣ６００　００７０　

Low Tire Pressure Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II). If it comes on while driving, it indicates that one or more of your vehicle’s tires are extremely low on pressure.

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure on the tire pressure monitor, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page 199

for more information.

). Refer to page

264

286

Tire Pressure Monitor

This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II).

The appropriate tire indicator will come on along with the low tire pressure indicator if a tire is extremely underinflated or has suddenly lost pressure. See Tire Pressure Indicator do if this indicator comes on.

Low

for what to

Instrument Panel Indicators

Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II).

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to ON (II), there is a problem with the TPMS. With this indicator on, the low tire pressure indicator and the tire pressure monitor will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

65

Main MenuTable of Contentsst０４／１２／０３　１６：２６：３４　３１ＳＪＣ６００　００７１　

Instrument Panel Indicators

Bed Lights On Indicator

This indicator reminds you that the bed lights are on. With the shift lever in the Park position, they come on when you push the light switch on the dashboard, swing open the tailgate, or open the In-Bed Trunk TM.

If you turn the ignition switch to ACCESSORY (I) or LOCK (0) without turning off the bed lights, this indicator will remain on, and then go off after 20 minutes. See page

for more information.

117

66

In-Bed Trunk Open Indicator

This indicator reminds you that the In-Bed Trunk is open. If you do not close it, the indicator stays on for about 3 minutes. See page for more information.

92

Back Window Open Indicator

This indicator reminds you that the back window is not completely closed when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0). With the ignition switch in the ACCESSORY (I) position, it goes off after about 30
seconds. With the ignition switch in the LOCK (0) position, it goes off after about 3 minutes.

If you remove the ignition key and open the driver’s door without closing the back window, you will hear five beeps and see the indicator blink. If you do not close the back window before the beeper stops, the indicator stops blinking but remains on. It will go off after about 3
minutes. See page information.

for more

103

Main MenuTable of Contentsst０４／１２／０３　１６：２６：４２　３１ＳＪＣ６００　００７２　

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

ODOMETER/ CHECK FUEL CAP INDICATOR

SELECT BUTTON

OUTSIDE TEMPERATURE INDICATOR

INFORMATION DISPLAY

TRIP METER

RESET BUTTON

U.S. model is shown.

Gauges

To switch the information display between the odometer, trip meter and outside temperature (if equipped), and engine oil life and maintenance service items, press the SELECT button repeatedly.

Odometer This shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

67

Main MenuTable of Contentsst０４／１２／０３　１６：２６：５０　３１ＳＪＣ６００　００７３　

To reset a trip meter, display it, and then press and hold the RESET button until the number resets to ‘‘0.0’’. Both trip meters will reset if the vehicle’s battery goes dead or is disconnected. And both continue to track mileage, even when only one is displayed.

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. Driving uphill or making turns can cause the needle to fluctuate or the low fuel indicator to come on early. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Gauges

Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

SELECT BUTTON

RESET BUTTON

There are two trip meters: TRIP A and TRIP B. Switch between these displays by pressing the SELECT button repeatedly. Each trip meter works independently, so you can keep track of two different distances.

68

Main MenuTable of Contentsst０４／１２／０３　１６：２７：０１　３１ＳＪＣ６００　００７４　

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. See page instructions and precautions on checking the engine’s cooling system.

276

for

Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models).

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).

The sensor delays the indicator update until it reaches the correct outside temperature. This may take several minutes.

If the outside temperature is incorrectly displayed, you can adjust it up 3°C in Canadian models) warmer or cooler.

5°F in U.S. models (

±

±

Gauges

NOTE: The temperature must be stabilized before doing this procedure.

To adjust the outside temperature indicator, make sure the outside temperature indicator is shown in the display, then press and hold the RESET button for 10 seconds (the TRIP A or B is also reset). The following sequence will appear for 1
4, second each: 0, 1, 2, 3, 4, 5, − − − − − −

− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

2, 2,

3, 3,

5,

When it reaches the desired value, release the RESET button. You should see the new outside temperature displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

69

Main MenuTable of Contentsst０４／１２／０３　１６：２７：０９　３１ＳＪＣ６００　００７５　

If the system still detects a loose or missing fuel fill cap, the malfunction indicator lamp (MIL) comes on. Turn the engine off, and check or retighten the fuel fill cap at least 3
clicks. The MIL goes out after 3 days of normal driving once the cap is tightened or replaced. If it does not go out, have your dealer inspect the vehicle. For more information, see page

279

Maintenance Minder Display The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

225

for

Gauges

Check Fuel Cap Indicator If your fuel fill cap is loose or missing, a ‘‘CHECK FUEL CAP’’ message appears in the odometer display after you start the engine. The message goes from CHECK to FUEL CAP repeatedly. You will also hear a beep.

Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen the cap, then retighten it at least 3
clicks. When you restart the engine, the message appears again. To clear the message, press and hold the RESET button until the odometer display returns.

70

Main MenuTable of Contentsst０４／１２／０３　１６：２７：１７　３１ＳＪＣ６００　００７６　

Controls Near the Steering Wheel

MOONROOF SWITCH ＊ (P.105)

INSTRUMENT PANEL BRIGHTNESS (P.75)

SHIFT LEVER (P.193)

VTM-4 LOCK

(P.198)

MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.72) BED LIGHT SWITCH (P.117)

HEADLIGHT CONTROL DIAL (P.73)

VEHICLE STABILITY ASSIST SYSTEM OFF SWITCH (P.206)

CRUISE BUTTON (P.163)

REMOTE AUDIO CONTROLS

＊2

(P.159)

HORN ＊

STEERING WHEEL ADJUSTMENT

(P.76)

CRUISE CONTROLS (P.163)

Vehicle with navigation system is shown.

＊ ＊

1: 2:

To use the horn, press the pad around the ‘‘H’’ logo. If equipped.

SELECT BUTTON (P.67)

RESET BUTTON

(P.67)

HAZARD WARNING BUTTON (P.76)

INTERIOR LIGHT CONTROL SWITCH (P.115)

SEAT HEATERS ＊ (P.101)

71

Main MenuTable of Contentsst０４／１２／０３　１６：２７：２８　３１ＳＪＣ６００　００７７　

Multi-Control Lever

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

MIST:

The wipers run at high speed until you release the lever.

Windshield Washer:

Push the button on the end of the multi-control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.

The multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.

To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.

OFF:

The wipers are not activated.

INT:

The length of the wiper interval is varied automatically according to the vehicle’s speed.

Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washers Turn signal High beams Flash high beams

72

Main MenuTable of Contentsst０４／１２／０３　１６：２７：３９　３１ＳＪＣ６００　００７８　

AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to ON (II). The heater turns off automatically when the outside temperature is above freezing.

This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.

Multi-Control Lever, Headlights

Headlight Control Dial

−

Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.

−

High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

62

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

1. 2. 3.

OFF Parking and indicator lights Headlights

CONTINUED

73

Main MenuTable of Contentsst０４／１２／０３　１６：２７：４７　３１ＳＪＣ６００　００７９　

Headlights

Automatic Lighting Off Feature This feature turns off the headlights, parking lights, taillights, and license plate lights within 30 seconds of removing the key from the ignition switch and closing the driver’s door.

This feature activates if you leave the headlight control dial in the ‘‘ the key, then open and close the driver’s door.

’’ position, remove

’’ or ‘‘

If you remove the key from the ignition switch with the headlight control dial on, but do not open the door, the lights will turn off after 10
minutes.

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 30 seconds, the lights will go off. With the driver’s door open, you will hear a lights-on reminder chime.

−

Turning the dial to ’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, and license plate lights.

’’

Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.

’’ or

’’ position, the lights on

When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to ACCESSORY (I) or LOCK (0).

74

Main MenuTable of Contentsst０４／１２／０３　１６：２７：５８　３１ＳＪＣ６００　００８０　

Headlights, Instrument Panel Brightness

Daytime Running Lights Canadianmodelsonly With the headlight control dial off, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the headlight control dial.

Instrument Panel Brightness

INSTRUMENT PANEL BRIGHTNESS CONTROL DIAL

The dial on the instrument panel controls the brightness of the instrument panel lights and the console compartment light. Turn the dial to adjust the brightness.

The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal

brightness when you turn the ignition switch to ON (II).

If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.

If you insert the key but do not turn the ignition switch to ON (II), the illumination turns off in about 10
seconds.

The instrument panel brightness is dimmed when you turn the headlight control dial to ‘‘ ‘‘ night. To cancel it, turn the instrument panel brightness control dial upward fully until you hear a click.

’’ position to reduce glare at

’’ or

75

Main MenuTable of Contentsst０４／１２／０３　１６：２８：０９　３１ＳＪＣ６００　００８１　

Hazard Warning Button, Steering Wheel Adjustment

Hazard Warning Button

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

3.

Push the lever up to lock the steering wheel in position.

Push the lever on the left side of the steering column all the way down.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

Push the red button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

1.

2.

76

Main MenuTable of Contentsst０４／１２／０３　１６：２８：１８　３１ＳＪＣ６００　００８２　

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (LIGHT GRAY)

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

Keys

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove boxlockedwhenyouleaveyour vehicle and the valet key at a parking facility.

You can also keep the In-Bed Trunk locked by using the main switch in the glove box (see page

94

).

Protect the keys from direct sunlight, high temperature, and high humidity.

Donotdropthekeysorsetheavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

77

Main MenuTable of Contentsst０４／１２／０３　１６：２８：２７　３１ＳＪＣ６００　００８３　

Immobilizer System

The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to ON (II), the immobilizer system indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.

78

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.

If the system repeatedly does not recognize the coding of your key, contact your dealer.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

If you have lost your key and you cannot start the engine, contact your dealer.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Main MenuTable of Contentsst０４／１２／０３　１６：２８：３７　３１ＳＪＣ６００　００８４　

Ignition Switch

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY (I) to ON (II).

−

Use this position

START (III) only to start the engine. The switch returns to ON (II) when you let go of the key.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

The shift lever must be in Park before you can remove the key from the ignition switch.

79

Main MenuTable of Contentsst０４／１２／０３　１６：２８：４７　３１ＳＪＣ６００　００８５　

Door Locks

Power Door Locks

LOCK TAB

MASTER DOOR LOCK SWITCH

To lock all doors and the In-Bed Trunk, push the front of the master door lock switch on either front door, pressthelocktabdownonthe driver’s door, or use the key on the outside lock on the driver’s door.

Pushing the rear of either master door lock switch will unlock all of the doors and the In-Bed Trunk.

80

The lock tab on each door locks and unlocks that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door. To unlock the driver’s door from the outside, turn the key and release it. If you turn it again, unlock all doors and the In-Bed Trunk.

To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door. To lock the driver’s door, remove the key from the ignition switch, and push the lock tab down, or push the front of the master switch, then close the door.

Youcanopenorclosetheside windows by using the key in the driver’s door (see page

104

).

LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches are disabled. They are not disabled if the driver’s door is closed. Pushing the front of the switch on the open passenger’s door will lock all doors and the In-Bed Trunk.

This vehicle has auto door locking/ unlocking features. See page for how to set them.

81

Main MenuTable of Contentsst０４／１２／０３　１６：２９：００　３１ＳＪＣ６００　００８６　

Childproof Door Locks

LOCK LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.

Auto Door Locking/Unlocking Your vehicle has two custom door lock settings: auto door locking and auto door unlocking. Make all settings before you start driving.

With the auto door locking and unlocking, the In-Bed Trunk also locks and unlocks.

Auto Door Locking The auto door locking feature has three possible settings:

The doors lock whenever you move the shift lever out of the Park position.

The doors lock when the vehicle speed reaches 9 mph (15 km/h).

The auto door locking is deactivated all the time.

Door Locks

Toactivateeitherautodoorlock mode: Locksalldoorswhentheshiftleveris movedoutofPark(P).

1.

Make sure the shift lever is in Park (P), and close the driver’s door.

2.

Turn the ignition switch to ON (II).

CONTINUED

81

Main MenuTable of Contentsst０４／１２／０３　１６：２９：１１　３１ＳＪＣ６００　００８７　

Door Locks

3.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a clicking sound, and after about 5
seconds, you will hear another clicking sound.

4.

Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.

82

4.

5.

Push and hold the brake pedal, then move the shift lever out of Park (P).

Push and hold the front of the master door lock switch on the driver’s door. You will hear a clicking sound, and after about 5
seconds, you will hear another clicking sound.

6.

Release the switch, move the shift lever to Park (P), and turn the ignition switch to LOCK (0) within 5 seconds.

Locksalldoorswhenthevehicle’sspeed reachesabout9mph(15km/h).

1.

Make sure the shift lever is in Park (P), and close the driver’s door.

2.

Turn the ignition switch to ON (II).

3.

Set the parking brake.

Main MenuTable of Contentsst０４／１２／０３　１６：２９：２３　３１ＳＪＣ６００　００８８　

Toturntheautodoorlockmodes off:

4.

Push and hold the front of the master door lock switch on the driver(cid:146)s door. You will hear a clicking sound after about 5
seconds.

5.

Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.

1.

Make sure the shift lever is in Park (P), and open the driver(cid:146)s door.

2.

Turn the ignition switch to ON (II).

3.

Set the parking brake.

Door Locks

Auto Door Unlocking The auto door unlocking feature has five possible settings:

The driver’s door unlocks when you move the shift lever to the Park position.

The driver’s door unlocks when- ever you turn the ignition switch to LOCK (0).

All doors unlock when you move the shift lever to the Park position.

All doors unlock whenever you turn the ignition switch to LOCK (0).

The auto door unlocking is deactivated all the time.

CONTINUED

83

Main MenuTable of Contentsst０４／１２／０３　１６：２９：３５　３１ＳＪＣ６００　００８９　

Door Locks

Toactivate autodoor unlock mode: Unlocks driver’s door or all doors when shift lever is moved to Park (P).

1.

Make sure the shift lever is in Park (P), and close the driver(cid:146)s door.

2.

Turn the ignition switch to ON (II).

84

3.

Push and hold the rear of the master door lock switch on the driver(cid:146)s door. You will hear a clicking sound. Continue to hold down the switch:

- Until you hear one click (after about 5 seconds) to activate the driver’s door unlock feature.

- Or, until you hear a second click (after about 10 seconds) to activate the all door unlock feature.

4.

Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.

Unlocks driver’s door or all doors when the ignitionswitch is out of the ON (II) position.

1.

Make sure the shift lever is in Park (P), and close the driver(cid:146)s door.

2.

Turn the ignition switch to ON (II).

3.

Set the parking brake.

4.

Push and hold the brake pedal, then move the shift lever out of Park (P).

Main MenuTable of Contentsst０４／１２／０３　１６：２９：４４　３１ＳＪＣ６００　００９０　

5. Push and hold the rear of the

master door lock switch on the driver(cid:146)s door. You will hear a clicking sound. Continue to hold down the switch:

- Until you hear one click (after about 5 seconds) to activate the driver’s door unlock feature.

- Or, until you hear a second click (after about 10 seconds) to activate the all door unlock feature.

6.

Release the switch, move the shift lever to Park (P), and turn the ignition switch to LOCK (0) within 5 seconds.

Toturntheautodoorunlockmodes off:

1.

Make sure the shift lever is in Park (P), and open the driver(cid:146)s door.

2.

Turn the ignition switch to ON (II).

3.

Set the parking brake.

Door Locks

4.

Push and hold the rear of the master door lock switch on the driver(cid:146)s door. You will hear a clicking sound after about 5
seconds.

5.

Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.

If your vehicle(cid:146)s battery is removed or goes dead, the auto door lock/ unlock setting is reset to the deactivated mode.

85

Main MenuTable of Contentsst０４／１２／０３　１６：２９：５２　３１ＳＪＣ６００　００９１　

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the other doors and the In-Bed Trunk. Some exterior and interior lights will flash twice each time you push the button.

When you press the UNLOCK button, the front and rear individual map lights, depending on the interior light control switch position, will come on (see page ). If you do not open any door, the lights stay on for about 30 seconds, then go out. If you relock the doors and the In-Bed Trunk with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately.

115

Remote Transmitter

LED

LOCK BUTTON

UNLOCK BUTTON

PANIC BUTTON

−

LOCK Press this button once to lock all doors and the In-Bed Trunk. Some exterior and interior lights will flash once. When you push LOCK twice within 5
seconds, you will hear a beep to verify that the doors and In-Bed Trunk are locked and the security system (if equipped) has set. This button does not work if any door is not fully closed or the key is in the ignition switch.

86

If you do not open any door within 30
seconds, the doors automatically relock, and the security system sets (if equipped). The UNLOCK button does not work when the key is in the ignition switch.

You can also open all side windows from outside the vehicle with the 104
remote transmitter (see page

).

−

Press and hold this

PANIC button for about 1 second to attract attention; the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to ON (II). Panic mode does not work when the key is in the ignition switch.

Main MenuTable of Contentsst０４／１２／０３　１６：３０：０７　３１ＳＪＣ６００　００９２　

Remote Transmitter Care

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

Remote Transmitter

Replacing the Transmitter Battery

BATTERY

SCREW

If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. Battery type: CR1616

2.

3.

To replace the battery:

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

Separate the transmitter by prying its middle seam with your fingernail.

Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.

CONTINUED

87

Main MenuTable of Contentsst０４／１２／０３　１６：３０：１３　３１ＳＪＣ６００　００９３　

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

4.

Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the

side facing down.

＋

5.

Install the parts in reverse order.

88

Main MenuTable of Contentsst０４／１２／０３　１６：３０：２４　３１ＳＪＣ６００　００９４　

Before you open the tailgate a different way (dropped open, and then swung open), make sure it is fully closed.

Make sure all passengers and objects are clear of the tailgate before opening and closing it, and make sure the tailgate is closed securely before driving.

You can open the tailgate two different ways:

Drop it open by using the upper handle.

Swing it open by using the right lower handle.

NOTE: As a safety feature, the upper handle is disabled if you do not fully close the tailgate after it is swung open. And the lower handle is disabled if you do not fully close the tailgate after it is dropped open.

Dual-Action Tailgate

To Drop Open the Tailgate

UPPER HANDLE

To drop open the tailgate, pull up the upper handle, then pull down the tailgate. To close the tailgate, push firmly up until it latches.

CONTINUED

89

Main MenuTable of Contentsst０４／１２／０３　１６：３０：３３　３１ＳＪＣ６００　００９５　

Dual-Action Tailgate

The dropped open tailgate can be used as an extended pickup bed. Make sure to secure the items in the pickup bed, and do not exceed the maximum allowable weight on the tailgate(seepage

185

).

To Swing Open the Tailgate

To turn the bed lights on or off, use the bed light switch on the dashboard (see page ).

117

HANDLE

To swing open the tailgate, first make sure it is fully closed, then pull up the right lower handle, and swing the tailgate to the left. To close, swing the tailgate back, and push it firmly until it is latched.

Before opening or closing the tailgate, check that passengers, especially children, are not in the tailgate’s path.

90

Do not drive with the tailgate swung open. This could damage the tailgate.

Swinging the tailgate open or closed while anyone is in its path can cause serious injury.

Make sure all passengers are clear of the tailgate’s path before opening or closing it.

Main MenuTable of Contentsst０４／１２／０３　１６：３０：４３　３１ＳＪＣ６００　００９６　

Do not allow anyone to hang on the swung open tailgate. This could damage the tailgate.

Do not leave the tailgate swung open. The tailgate may swing and shut accidentally. This could cause serious injuries.

Thebedlightscomeonwhenyou swing open the tailgate. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page

117

).

TailgateOpenIndicator

This indicator is in the door and tailgate open monitor on the instrument panel. It comes on when the tailgate is swung open or it is not completely closed. This indicator worksevenifthekeyisnotinthe ignition switch.

If the tailgate is swung open or not closed tightly when the ignition switch is in the ON (II) position, you will hear six beeps and see the indicator blinking. The indicator stays on until you close the tailgate. The beeper also sounds and the indicator blinks when you move the shift lever out of the Park or neutral position.

Dual-Action Tailgate

If you do not fasten the seat belt, you first hear the seat belt reminder alarm, then the tailgate reminder beeper sounds.

The indicator does not monitor the tailgate when it is dropped open.

Loading Cargo See page for information on cargo loading and weight limits.

183

You can also store and lock items in the In-Bed Trunk (see page

92

).

91

Main MenuTable of Contentsst０４／１２／０３　１６：３０：５３　３１ＳＪＣ６００　００９７　

In-Bed Trunk

TM

If your vehicle’s battery is disconnected or goes dead, the release button on the In-Bed Trunk lid is disabled. To open the In-Bed Trunk, use the master key.

Thebedlightscomeonwhenyou open the In-Bed Trunk. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page

117

).

You can store items in the In-Bed Trunk up to 300 lbs (136 kg). Do not exceed this weight limit, or you may damage the In-Bed Trunk. See page 183
for information on loading cargo and weight limits.

To store items separately in the In-Bed Trunk, optional divider guides are available from your dealer.

To close the In-Bed Trunk, lower the lid, then press down on the back edge.

When the In-Bed Trunk is closed securely, it can be locked or unlocked along with the power door locks (see page

80

).

RELEASE BUTTON

YoucanopentheIn-BedTrunktwo different ways:

Push the release button on the lower right side of the In-Bed Trunk lid when the driver’s door is unlocked.

Usethemasterkeytoopenthe In-Bed Trunk when the driver’s door is locked.

92

Main MenuTable of Contentsst０４／１２／０３　１６：３１：０５　３１ＳＪＣ６００　００９８　

To avoid damaging the key and key cylinder of the In-Bed Trunk lid, do notclosethetailgatewhenthekeyis in the lid.

To avoid damaging the seal on the In-Bed Trunk lid, remove any debris from the lid’s mating surface before you close it.

Emergency Opener

In-Bed Trunk

TM

To avoid damaging the In-Bed Trunk lid, and to prevent items from being thrown about the vehicle and possibly hurting someone in an accident or sudden stop, be sure the In-Bed Trunk lid is securely closed before driving away.

To avoid damaging the bottom of the In-Bed Trunk, do not drive over large obstacles, and do not use it as a jacking point to raise the vehicle.

In-Bed Trunk Open Indicator

This indicator on the instrument panel reminds you that the In-Bed Trunk is open (see page

66

).

As a safety feature, your vehicle has a release lever on the latch of the In-Bed Trunk lid so it can be opened from the inside. To open the In-Bed Trunk, push the release lever in the direction of the arrow.

Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page

34

93

Main MenuTable of Contentsst０４／１２／０３　１６：３１：１５　３１ＳＪＣ６００　００９９　

In-Bed Trunk

TM

In-Bed Trunk Main Switch

Washing the In-Bed Trunk

Cargo Hooks

MAIN SWITCH

CARGO HOOKS

To protect items in the In-Bed Trunk, you can disable its release button by turning off the main switch in the glove box and locking the glove box with the master key.

Even if the main switch is in the OFF position, you can open the In-Bed Trunk with the master key.

94

DRAIN PLUG

You can wash the inside of the In-Bed Trunk with a water and mild detergent solution, and a soft brush or cloth.

To drain water from the In-Bed Trunk, remove the drain plug by turning it counterclockwise.

When you are finished washing the In-Bed Trunk, dry it with a soft cloth, and reinstall the drain plug.

There are two cargo hooks for plastic grocery bags at the back of the In-Bed Trunk. They are designed to hold light items. Heavy objects may damage the hooks.

Main MenuTable of Contentsst０４／１２／０３　１６：３１：２５　３１ＳＪＣ６００　０１００　

All models except the RT and the Canadian LX have a power adjustable driver’s seat. The RT/LX model has manual driver’s seat adjustments (see the next column).

The front passenger’s seat in all models adjusts manually.

−

11 13

Manual Seat Adjustments See pages for important safety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. Make all seat adjustments before you start driving.

To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move