If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again.
2010 Insight08/12/27 11:39:49 31TM8600 0104
TripAResetWithRefuel
Multi-Information Display
To cause Trip A and average fuel for trip A to reset every time you refuel your vehicle, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP A RESET with REFUEL’’ and repeat the procedure again.
CONTINUED
99
2010 Insight08/12/27 11:39:57 31TM8600 0105
Multi-Information Display
ElapsedTimeReset There are three elapsed time reset choices you can make:
−
IGN OFF The elapsed time is reset when you turn the ignition switch to the LOCK (0) position.
TRIP A when Trip A is reset.
−
The elapsed time is reset
TRIP B when Trip B is reset.
−
The elapsed time is reset
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
100
2010 Insight08/12/27 11:40:04 31TM8600 0106
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again.
DisplayKm/Miles
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
To change the displayed measurement in the trip computer and trip information and to switch between kilometers and miles, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
CONTINUED
101
2010 Insight08/12/27 11:40:11 31TM8600 0107
Multi-Information Display
AUTO: When you press the km/mile change knob in the instrument panel to switch the speedometer reading between miles per hour (mph) and kilometers per hour (km/h), the displayed measurement in the trip computer and trip information, also switches to kilometers or miles depending on the selected speedometer reading.
KM: The displayed measurement in the trip computer and trip information is set to kilometers.
MILES: The displayed measurement in the trip computer and trip information is set to miles.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘DISPLAY KM/MILES SETTING INCOMPLETE’’ message appears, go back to ‘‘DISPLAY KM/ MILES’’ and repeat the procedure again.
Press the SEL/RESET button to see the selections.
Select AUTO, KM, or MILES by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
102
2010 Insight08/12/27 11:40:19 31TM8600 0108
MeterColorChange
You can turn the ambient meter feature on or off (see page ).
72
Press the SEL/RESET button to see the selections.
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
Multi-Information Display
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘METER COLOR CHANGE SETTING INCOMPLETE’’ message appears, go back to ‘‘METER COLOR CHANGE’’ and repeat the procedure again.
103
2010 Insight08/12/27 11:40:26 31TM8600 0109
Multi-Information Display
Lighting Setup There is one custom setting for the lighting setup:
INTERIOR LIGHT DIMMING TIME
While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
104
: Press the SEL/RESET button. : Press the INFO button : Press the INFO button
▼ ▲
See page
105
2010 Insight08/12/27 11:40:34 31TM8600 0110
InteriorLightDimmingTime
Multi-Information Display
The interior lights fade out when you close all doors. To change how long the lights stay on before they fade out, follow these instructions:
You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select the desired setting (15 SEC, 30 SEC, or 60 SEC) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again.
105
2010 Insight08/12/27 11:40:44 31TM8600 0111
Multi-Information Display
Door Setup Here are the five custom settings for the door setup:
AUTO DOOR LOCK AUTO DOOR UNLOCK DOOR LOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER
While ‘‘DOOR SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
106
See page
107
See page
108
See page
110
: Press the SEL/RESET button. : Press the INFO button : Press the INFO button
▼ ▲
See page
113
See page
112
2010 Insight08/12/27 11:40:53 31TM8600 0112
Multi-Information Display
AutoDoorLock There are three settings you can choose from:
SHIFT FROM P The doors lock whenever you move the shift lever out of Park.
−
WITH VEHICLE SPEED The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h).
−
−
OFF The auto door lock mode is deactivated all the time.
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
A/T model is shown.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
CONTINUED
107
2010 Insight08/12/27 11:40:59 31TM8600 0113
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.
AutoDoorUnlock There are five possible settings you can choose from:
DRIVER DOOR WITH SHIFT TO P − you move the shift lever to Park.
The driver’s door unlocks when
ALL DOORS WITH SHIFT TO P − All the doors unlock when you move the shift lever to Park.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
108
2010 Insight08/12/27 11:41:07 31TM8600 0114
DRIVER DOOR WITH IGN OFF − The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position.
ALL DOORS WITH IGN OFF All the doors unlock when you turn the ignition switch to the LOCK (0) position.
−
Multi-Information Display
−
OFF deactivated all the time.
The auto door unlock is
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button.
▲ ▼
For example, you choose ‘‘DRIVER DOOR with SHIFT to P,’’ you will see the above display.
CONTINUED
109
2010 Insight08/12/27 11:41:15 31TM8600 0115
Multi-Information Display
DoorLockMode
If you choose ‘‘ALL DOORS With IGN OFF,’’ you will see the above display.
Press the SEL/RESET button to enter your selection.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.
To select whether the driver’s door unlocks or all the doors unlock when you unlock the doors with the remote transmitter or the key, follow these instructions.
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
110
2010 Insight08/12/27 11:41:21 31TM8600 0116
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR LOCK MODE’’ and repeat the procedure again.
111
2010 Insight08/12/27 11:41:27 31TM8600 0117
Multi-Information Display
KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the trunk are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.
). You can
255
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to enter the selecting mode.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
112
2010 Insight08/12/27 11:41:34 31TM8600 0118
SecurityRelockTimer If you unlock the doors with the remote transmitter, but do not open any of the doors within 30 seconds, the doors and the fuel fill door, automatically relock, and the security system sets.
You can change this relock time from 30 seconds to 60 or 90 seconds.
Multi-Information Display
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
CONTINUED
113
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.
2010 Insight08/12/27 11:41:40 31TM8600 0119
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
114
2010 Insight08/12/27 11:41:47 31TM8600 0120
DEFAULT ALL
If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button.
▲ ▼
To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button.
▲ ▼
If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display.
Multi-Information Display
When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display.
If the setting is not successfully completed, ‘‘FAILED’’ is shown for several seconds, and then the screen goes back to the normal message mode. Repeat the same procedure to select DEFAULT ALL.
115
2010 Insight08/12/27 11:41:55 31TM8600 0121
Controls Near the Steering Wheel
HEADLIGHTS/TURN SIGNALS (P.118)
MIRROR CONTROLS (P.144)
ECON BUTTON (P.124)
VEHICLE STABILITY ASSIST (VSA) OFF (P.333) SWITCH *
REMOTE AUDIO CONTROL BUTTONS (P.251)
*
NAVIGATION SYSTEM VOICE CONTROL BUTTONS
(P.259)
*
INSTRUMENT PANEL (P.121) BRIGHTNESS
WINDSHIELD WIPERS/ WASHERS
(P.117)
HORN *
STEERING WHEEL ADJUSTMENT
(P.125)
EX model with navigation system is shown.
BLUETOOTH HANDS-FREE LINK SYSTEM VOICE CONTROL BUTTONS *
(P.259)
CRUISE CONTROL BUTTONS * MULTI-INFORMATION BUTTONS
(P.256)
(P.76) NAVIGATION SYSTEM / * (P.198) AUDIO SYSTEM *
*
AUDIO SYSTEM
(P.166)
CLOCK
(P.254)
REAR WINDOW DEFOGGER/ HEATED MIRROR *
(P.123/145)
AUXILIARY INPUT JACK *
(P.252)
ACCESSORY POWER SOCKET
(P.153)
MULTI-INFORMATION BUTTONS
*
(P.76)
To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual.
1 :
*
2 :
*
3 :
*
116
2010 Insight08/12/27 11:42:05 31TM8600 0122
Windshield Wipers and Washers
Push the right lever up or down to select a position.
MIST The wipers run at high speed until you release the lever.
−
OFF
−
The wipers are not activated.
−
INT The length of the wipe interval is varied automatically according to vehicle’s speed.
OnallmodelsexceptLX The length of the wiper interval is varied automatically according to the vehicle’s speed.
Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).
ADJUSTMENT RING
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
−
Pull the
Windshield Washer wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
117
2010 Insight08/12/27 11:42:14 31TM8600 0123
Windshield Wipers and Washers, Turn Signal and Headlights
Rear Window Wiper and Washer
4.
Rotate the switch counterclockwise also to spray the window washer and turn the wiper on.
Turn Signal and Headlights
When you shift the transmission to the reverse position with the front windshield wiper activated, the rear wiper operates automatically even if the rear wiper switch is off.
The rear window washer uses the same fluid reservoir as the wind- shield washer.
1. 2. 3. 4. 5. 6.
Turn Signal OFF Parking and interior lights Headlights on High Beams Flash high beams
1.
2.
3.
OFF
When you turn the wiper switch to
the ‘‘OFF’’ position, the wiper will
return to its parked position.
Rotate the switch clockwise to
turn the rear window wiper ON.
The wiper operates every 7
seconds after completing two
sweeps.
Hold past ON to activate the rear
window wiper a few times and to
spray the rear window washer.
118
2010 Insight08/12/27 11:42:21 31TM8600 0124
Turn Signals and Headlights
−
Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to the center when you release it or complete a turn.
−
Turning the switch to
’’ position turns on the
Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
−
High Beams Push the left lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.
). Pull the lever back
69
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
Turning the switch to the ‘‘ position turns on the headlights.
’’
’’ or ‘‘
When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder.
This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
119
2010 Insight08/12/27 11:42:26 31TM8600 0125
Headlights
position, the high beam
Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the switch.
120
If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked.
2010 Insight08/12/27 11:42:33 31TM8600 0126
Instrument Panel Brightness
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the
or
position. Turning the
knob to the right until you hear a tone will cancel the reduced brightness.
INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB
The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness with the ignition switch in the ON (II) position and the parking lights on.
BRIGHTNESS LEVEL
When you turn the knob, the multi- information display changes to vertical bars that show you the current level.
You will hear a tone when you reach the maximum or minimum brightness. The brightness level goes out about 5 seconds after you stop adjusting.
The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal brightness when you turn the ignition switch to the ON (II) position.
CONTINUED
121
2010 Insight08/12/27 11:42:38 31TM8600 0127
Instrument Panel Brightness, Hazard Warning Button
Hazard Warning Button
HAZARD WARNING BUTTON
If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.
If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.
Push the button next to the audio system to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signal lights and both turn signal indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
122
2010 Insight08/12/27 11:42:44 31TM8600 0128
Rear Window Defogger
The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature (over 32°F, 0°C).
Make sure all rear windows are clear and you have good visibility before starting to drive.
The defogger and antenna wires on the inside of all rear windows can be accidentally damaged. When cleaning the glass, always wipe side- to-side.
U.S. EX model is shown.
The rear window defogger will clear fog, frost, and thin ice from the windows. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.
U.S.EXmodelsandallCanadianmodels Pushing this button also turns the mirror heaters on or off. For more information, see page
145
123
2010 Insight08/12/27 11:42:51 31TM8600 0129
ECON Button
ECON MODE INDICATOR
ECON BUTTON
MULTI-INFORMATION DISPLAY
The ECON button turns the ECON mode on and off. The ECON mode helps you improve your fuel economy by modifying some vehicle functions. When the ECON mode is on:
Engine performance will be different The climate control system will have greater temperature fluctuations
In addition, when the ECON mode is
on, you may get more Ecological
Drive Assist points (see page
304
).
124
Press the ECON button to activate the ECON mode. ECON ON will be displayed on the multi-information display and the ECON mode indicator will illuminate in the instrument panel. Press the ECON button again to turn it off. ECON OFF will appear on the multi- information display.
When you turn off and then restart the engine, the ECON mode setting remains the same as previously set.
2010 Insight08/12/27 11:42:58 31TM8600 0130
Make any steering wheel adjustments before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
To adjust
To lock
LEVER
1.
Pull the lever under the steering column toward you until it stops.
2.
Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
Steering Wheel Adjustments
3.
Push the lever forward fully to lock the steering wheel in position.
Make sure the lever is positioned securely at the bottom of the steering column as shown.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
125
2010 Insight08/12/27 11:43:06 31TM8600 0131
You should have received a key number tag with your keys. You will need this number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
Keys and Locks
KEY NUMBER TAG
IGNITION KEYS WITH REMOTE TRANSMITTER
Two ignition keys come with your vehicle. You should keep one of them in a safe place, away from the vehicle, as a spare.
They fit all the locks on your vehicle.
126
2010 Insight08/12/27 11:43:13 31TM8600 0132
If the system repeatedly does not recognize the coding of your key, contact your dealer.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable.
If you lose your key and you cannot start the engine, contact your dealer.
Always take the ignition key with you whenever you leave the vehicle alone.
The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.
Immobilizer System
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
127
2010 Insight08/12/27 11:43:19 31TM8600 0133
Ignition Switch
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in Park.
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
128
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
If you leave the key in the ignition switch in the ACCESSORY (I) position and open the driver’s door, you will see a ‘‘RETURN IGNITION SWITCH TO LOCK (0) POSITION’’ message on the multi-information display and hear a reminder beeper.
If you turn the ignition key to the ACCESSORY (I) position with the driver’s door closed, you will see an ‘‘ACCESSORY (I) POSITION’’ message on the multi-information display to inform you of the key position.
2010 Insight08/12/27 11:43:24 31TM8600 0134
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.
−
Use this position
START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
You will also see a ‘‘REMOVE KEY’’ message on the multi-information display.
The shift lever must be in Park before you can remove the key from the ignition switch.
Ignition Switch
129
2010 Insight08/12/27 11:43:32 31TM8600 0135
To lock
LOCK TAB
All doors and the hatch can be locked from the outside by using the key in the driver’s door. To unlock only the driver’s door, insert the key, turn it clockwise, and release it. The remaining doors and the hatch unlock when you turn the key a second time within a few seconds.
You can customize the door lock/ unlock settings (see page
106
).
To unlock
The lock tab on any passenger’s door locks and unlocks that door.
When the door is unlocked, you can see the red indicator on the lock tab above the inner door handle.
Door Locks
MASTER DOOR LOCK SWITCH
Lock
Unlock
To lock all doors and the hatch, push the front of the master door lock switch on either front door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door.
Pushing the rear of either master door lock switch will unlock all doors and the hatch. Pushing forward the lock tab on the driver’s door unlocks only that door.
130
2010 Insight08/12/27 11:43:38 31TM8600 0136
To lock any passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door. To lock the driver’s door, remove the key from the ignition switch, pull the lock tab rearward or push the front of the master switch, then close the door.
Defaultsetting When the vehicle speed reaches about 10 mph (U.S.)/15 km/h (Canada) or more, all the doors and the hatch lock automatically.
When you shift to P after driving, the driver’s door unlocks.
LockoutPrevention If you forget and leave the key in the ignition switch, lockout prevention will not allow you to lock the driver’s door. With any door or the hatch open and the key in the ignition switch, locking with master door lock switch is disabled. If the driver’s door is closed, the lock tab on the driver’s door is not disabled. Pulling the driver’s lock tab rearward will lock all doors or the hatch. If you try to lock an open driver’s door by pulling the lock tab rearward, the driver’s door lock tab pops out and unlocks the driver’s door.
Door Locks
Childproof Door Locks
Unlock
Lock
LEVER
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.
131
2010 Insight08/12/27 11:43:45 31TM8600 0137
Remote Transmitter
LED
LOCK BUTTON
UNLOCK BUTTON
PANIC BUTTON
−
LOCK
Press this button once to
lock all doors and the hatch. Some
exterior lights will flash once. When
you push LOCK twice within 5
seconds, the horn will sounds to
verify that the doors are locked and
the security system has set. You
cannot lock the doors if any door or
the hatch is not fully closed or if the
key is in the ignition switch.
132
−
UNLOCK Press this button once to unlock the driver’s door (or all the doors and the hatch depending on the door lock setting). Push it twice to unlock the remaining doors and the hatch. Some exterior lights will flash twice when you push the button the first time.
If you do not open any door or the hatch within 30 seconds, the doors automatically relock and the security system sets.
The ceiling light and the door activated spotlights come on when you press the UNLOCK button if the lights are in the door activated position. If you do not open any door or the hatch within 30 seconds (or whatever setting of the interior light dimming time is set to), the light(s) will fade out. If you relock the doors and the hatch with the remote transmitter before 30 seconds have elapsed, the light(s) will go off immediately.
The keyless lock acknowledgment beep and flashing of the lights can be deactivated (see page
112
).
To change the lock/unlock setting
and the relock timer setting, refer to
the customized settings on page
106
2010 Insight08/12/27 11:43:53 31TM8600 0138
−
Press and hold this
PANIC button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.
Remote Transmitter
RemoteTransmitterCare
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
Battery type: CR1616
To replace the battery:
CONTINUED
133
2010 Insight08/12/27 11:44:01 31TM8600 0139
Remote Transmitter
COIN
BATTERY
3.
Inside the transmitter, separate the inner cover from the keypad by carefully prying on the edge with a coin.
4.
Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same ( side facing down), then insert it in the keypad.
+
SCREW
1.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
Be careful when removing NOTE: this screw as the head of the screw can strip out.
2.
Separate the transmitter by prying its middle seam with your fingernail.
134
2010 Insight08/12/27 11:44:06 31TM8600 0140
Remote Transmitter
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
5.
Install the parts in reverse order.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
135
2010 Insight08/12/27 11:44:13 31TM8600 0141
Hatch
The hatch will lock or unlock when you lock/unlock the driver’s door with the key, the remote transmitter, the master door lock switch, or the lock tab on the driver’s door.
To unlock the hatch, turn the key clockwise twice, push the rear of the master door lock switch, or push UNLOCK twice on the remote transmitter.
136
INNER HANDLE
RELEASE
To open the hatch, pull and lift up the release. To close the hatch, use the handle to lower it, then press down on the back edge.
Keep the hatch closed at all times
while driving to avoid damaging the
hatch and to prevent exhaust gas
from getting into the interior. See
Carbon Monoxide Hazard
.56
on page
2010 Insight08/12/27 11:44:19 31TM8600 0142
Unlocking the Hatch
COVER
Unlock
If the power door lock system cannot unlock the hatch, unlock it manually.
Place a cloth on the top side of the cover, then use a small flat-tipped screwdriver to remove the cover on the back of the hatch.
RELEASE LEVER
Push the release lever to the lower right as shown, and push the hatch to open it.
If you need to unlock the hatch manually, it means there is a problem with the hatch. Have the vehicle checked by your dealer.
Hatch
137
2010 Insight08/12/27 11:44:26 31TM8600 0143
Seats
−
14 15
Front Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositionseatsandseat-backs. Make all adjustments before you start driving.
Driver’s Seat Height Adjustment
To change the seat-back angle of the front seat, pull up the lever on the outside of the seat bottom.
Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
The height of your driver’s seat is adjustable. To raise the seat, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push the lever down repeatedly.
To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat to make sure it is locked in position.
138
2010 Insight08/12/27 11:44:34 31TM8600 0144
Head Restraints Seepage forimportantsafety informationandawarningabout improperlypositioningheadrestraints.
16
Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.
They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.
Seats
Front Position
CUSHION
RELEASE BUTTON
LEGS
SEAT-BACK
AdjustingtheHeadRestraint The head restraints adjust for height. You need both hands to adjust a restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.
CONTINUED
139
2010 Insight08/12/27 11:44:42 31TM8600 0145
Seats
Rear Outer Position
CUSHION
Rear Center Position
CUSHION
LEGS
SEAT-BACK
RELEASE BUTTON
LEGS
SEAT-BACK
RELEASE BUTTON
When a passenger is seated in the rear seat, the head restraint should be adjusted up or down, to match the passenger’s height.
RemovingtheHeadRestraint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat- back.
Failure to reinstall the head restraints can result in severe injury during a crash.