OFF
DOOR ACTIVATED
The ceiling light has a three-position switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:
Open any door. Unlock the doors and the tailgate with the key or remote transmitter.
CONTINUED
95
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼—:59 31S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼‘ 
Interior Lights
After all doors are closed tightly, the light fades out in about 30 seconds.
Spotlights
Cargo Area Light
The ceiling light (with the switch in the center position) comes on when you remove the key from the ignition switch. If you do not open a door, the light fades out in about 30 seconds.
If you leave any door or the tailgate open with the key not in the ignition switch, the ceiling light will go off after 3 minutes.
96
ON
OFF
Turn on the spotlight by pushing the button. Push the button again to turn it off. You can use the spotlights at all times.
Ignition Switch Light The ignition switch light comes on when you open the driver’s door. It fades out in about 30 seconds after the door is closed.
TAILGATE/HATCH GLASS ACTIVATED The cargo area light has a three- position switch. In the OFF position, the light does not come on. In the center position, the light comes on when you open the tailgate or the hatch glass. In the ON position, the light stays on continuously.
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼˜ï¼šï¼ï¼•ã€€ï¼“1S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼’ 
Features
The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions.
The standard audio system has many features. This section de- scribes those features and how to use them.
Your vehicle has an anti-theft audio system that requires a code number to enable it.
............... ................................
Vents, Heating, and A/C Audio System Playing the Radio Playing a Disc Disc Changer Disc Player/Changer Error
................... .......................... ..........................
. 98
. 103
. 105, 116
109, 124
111, 125
Messages
............................. .........................
112, 128
113, 129
Playing a Tape Caring for the Tape and
Player
...................................
115, 131
Playing the XM Satellite Radio . 120
. 132
Radio Reception
............................
. 134
Protecting Your Discs
..................
................
Remote Audio Controls
. 135
. 136
Radio Theft Protection
.................
. 137
Setting the Clock
..........................
...............................
Cruise Control
. 138
97
Main Menustï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼˜ï¼šï¼‘ï¼ã€€ï¼“1S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼“ 
Vents, Heating, and A/C
FAN CONTROL DIAL
TEMPERATURE CONTROL DIAL
MODE CONTROL DIAL
REAR WINDOW DEFOGGER/ HEATED MIRRORS BUTTON (If equipped)
RECIRCULATION BUTTON
AIR CONDITIONING (A/C) BUTTON
REAR WINDOW DEFOGGER BUTTON
98
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼˜ï¼šï¼“6 31S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼” 
Air Flow Buttons
Fan Control Dial Turn this dial to increase or decrease the fan speed and airflow.
Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.
Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button is on when the A/C is on.
Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent throughout the system again. When the indicator is off, air is brought in from the outside of the vehicle (fresh air mode).
The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.
The system should be left in fresh air mode under almost all conditions. Keeping the system in recirculation mode, particularly with the A/C off, can cause the windows to fog up.
Switch to recirculation mode when driving through dusty or smoky conditions, then return to fresh air mode.
Vents, Heating, and A/C
Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes.
The system automatically
turns on the A/C and switches to recirculation mode. Air flows from the center and side vents in the dashboard.
Air flows from the center and corner vents in the dashboard.
Rear Window Defogger Button
This button turns the rear window
).
defogger off and on (see page
68
Airflow is divided between the vents in the dashboard and the floor vents.
On some models, this button also controls the heated mirror function (see page
89
).
Air flows from the floor
vents. When you select system automatically switches to fresh air mode.
, the
CONTINUED
99
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼˜ï¼šï¼•ï¼” 31S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼•ã€€
Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.
1.
2. 3.
Select When you select , the system automatically switches to fresh air mode. Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.
Using the A/C
Air conditioning places an extra load
on the engine. Watch the engine
coolant temperature gauge (see page
62
turn off the A/C until the gauge
reading returns to normal.
). If it moves near the red zone,
1.
2.
3. 4.
5.
Turn on the A/C by pressing the button. The indicator in the button comes on when a fan speed is selected. Make sure the temperature is set to maximum cool. Select If the outside air is humid, select recirculation mode. If the outside air is dry, select fresh air mode. Set the fan to the desired speed.
Vents, Heating, and A/C
Airflow is divided between
the floor vents and the defroster vents at the base of the windshield.
Air flows from the defroster vents at the base of the windshield.
or
When you select the system automatically switches to fresh air mode and turns on the A/C. In this case, you cannot turn the A/C off.
Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the tailgate.
1.
2. 3. 4.
Set the temperature to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.
and fresh air mode.
100
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼™ï¼šï¼ï¼•ã€€ï¼“1S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼– 
To cool the interior with MAX A/C:
1. 2.
3.
Set the fan to the desired speed. Select MAX A/C mode. The system automatically turns on the A/C, selects switches to recirculation mode. Make sure the temperature is set to maximum cool.
, and
you can
Iftheinteriorisverywarm, cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in fresh air mode.
To Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.
1. 2. 3. 4.
Turn the fan on. Turn on the air conditioning. Select Adjust the temperature to your preference.
and fresh air mode.
This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).
Vents, Heating, and A/C
To Defog and Defrost To remove fog from the inside of the windows:
1.
2.
3.
4.
5.
Set the fan to the desired speed or high for faster defrosting. Select . The system automatically switches to fresh air mode and turns on the A/C. The A/C indicator will not come on, if it was previously off. Adjust the temperature so the airflow feels warm. Select rear window and the outside mirrors (if equipped). To increase airflow to the windshield, close the corner vents.
to help clear the
101
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼™ï¼šï¼‘7 31S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼— 
Vents, Heating, and A/C
or
When you select the system automatically switches to fresh air mode and turns on the A/C. This helps to dehumidify the air and to defog the windshield. In either mode, you cannot turn off the A/C. When you switch to another mode, the A/C returns to its original setting, either on or off, as displayed by the A/C indicator.
102
. The system
To Remove Exterior Frost or Ice From the Windows 1.
Select automatically switches to fresh air mode and turns on the A/C. The A/C indicator does not come on if it was previously off. Select Set the fan and temperature controls to maximum level.
2. 3.
To clear the windows faster, you can close the dashboard corner vents by rotating the wheel below each vent. This sends more warm air to the windshield defroster vents. Once the windshield is clear, select fresh air mode to avoid fogging the windows.
For your safety, make sure you have a clear view through all the windows before driving.
To Turn Everything Off Turning the fan speed control dial all the way to the left shuts the system off.
Keep the system off for short periods only.
To keep stale air and mustiness from collecting, you should have the fan running at all times.
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼—ï¼ï¼‘3 14:24:31 31S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼˜ã€€
Some models may have one of the audio systems described in this section. Read the appropriate pages in this section for operation of the audio systems installed in your vehicle.
U.S. LX and Canadian SE model
for U.S. LX model,
to
105
115
page Canadian SE model page models, Canadian EX, EX-L models
116
131
to
for U.S. EX, SE
If your vehicle has a different audio system refer to its manual for operating instructions.
Audio System
103
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼™ï¼šï¼“2 31S9A64ï¼ã€€ï¼ï¼‘ï¼ï¼™ã€€
Audio System
Canadian EX and EX-L models
U.S. EX and SE models
104
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼—ï¼ï¼‘3 14:24:36 31S9A64ï¼ã€€ï¼ï¼‘1ï¼ã€€
U.S. LX and Canadian SE model
POWER/VOLUME KNOB
PRESET BUTTONS
TUNE KNOB
Playing the Radio
TREBLE/ BALANCE
BASS/ FADE
SCAN BUTTON
FM BUTTON
SEEK BUTTONS
AM BUTTON
AUTO SELECT BUTTON
105
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼™ï¼šï¼”6 31S9A64ï¼ã€€ï¼ï¼‘11 
To Select a Station You can use any of five methods to find radio stations on the selected band: the preset buttons, and
TUNE, SEEK, SCAN,
AUTO SELECT
−
Use the TUNE knob to
TUNE tune the radio to a desired frequency. Turn the knob right to tune to a higher frequency, or left to tune to a lower frequency.
−
The SEEK function
SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press the release it.
○ ○ + −
SEEK button, then
or
−
The SCAN function
SCAN samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 10 seconds.
If you do nothing, the system will scan for the next strong station and play it for 10 seconds. When it plays a station that you want to listen to, press the SCAN button again.
Playing the Radio
To Play the Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM or FM button. Adjust the volume by turning the PWR/VOL knob.
The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo.
Stereo reproduction on AM is not available.
106
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼ï¼™ï¼šï¼•ï¼— 31S9A64ï¼ã€€ï¼ï¼‘12 
−
Each preset button can
Preset store one frequency on AM and two frequencies on FM.
1.
Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button.
2.
Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station.
3.
Pick a preset button and hold it until you hear a beep.
4.
Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
The preset frequencies will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.
−
If you are
AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.
Press the A. SEL button. ‘‘A.SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM and twelve FM stations in the preset buttons.
You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for every preset button.
If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described.
Playing the Radio
To turn off auto select, press the A. SEL button. This restores the presets you originally set.
107
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘ï¼ï¼šï¼ï¼™ã€€ï¼“1S9A64ï¼ã€€ï¼ï¼‘13 
Playing the Radio
BAS/FAD: Press the knob to pop it out. Turn it to adjust the Bass level. Pull it out slightly farther to adjust the Fade, or front-to-back strength. Push the knob back in when you are done adjusting the sound.
TRE/BAL: Press the knob to pop it out. Turn it to adjust the Treble level. Pull it out slightly farther to adjust the balance, or side-to-side strength. Push the knob back in when you are done adjusting the sound.
Adjusting the Sound BAL to-side strength of the sound.
Adjust the balance or side-
−
−
FAD front-to-back strength of the sound.
Adjust the fader or the
TRE − sound.
Adjust the treble in the
BAS
−
Adjust the bass in the sound.
108
Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page illuminates when the parking lights are on, even if the radio is off.
). The audio system
67
Radio Frequencies and Reception For information, see page
132
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼—ï¼ï¼‘3 14:24:42 31S9A64ï¼ã€€ï¼ï¼‘14 
U.S. LX and Canadian SE model
CD EJECT BUTTON
CD SLOT
SKIP BUTTONS
Playing a Disc
POWER/VOLUME KNOB
REPEAT BUTTON
CD BUTTON
RANDOM BUTTON
109
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘ï¼ï¼šï¼’8 31S9A64ï¼ã€€ï¼ï¼‘15 
Playing a Disc
To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or the ON(II) position.
You operate the CD player with the same controls used for the radio. To select the CD player, press the CD button. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes.
Insert a CD into the CD slot. The drive will pull the CD in the rest of the way to play it. When the system reaches the end of the disc, it will return to the beginning and play the disc again.
You can also play 3-inch (8-cm) discs without using an adapter ring.
110
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
To play the radio when a CD is playing, press the AM or FM button. Press the CD button again to switch back to the CD player.
To play the tape when a CD is playing, insert a tape in the player. If a tape is in the player, press the TAPE button. Press the CD button again to switch back to the CD player.
If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.
○ +
−
Each time you press and
To Change or Select Tracks SKIP release the skip button, the player skips forward to the beginning of the next track. Press and release the ○ − skip button, to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.
To move rapidly within a track, press and hold the
skip button.
○ ○ + −
or
−
To continuously replay
REPEAT a track, press and release the RPT button. You will see REPEAT in the display. Press it again to turn it off.
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘ï¼ï¼šï¼”3 31S9A64ï¼ã€€ï¼ï¼‘16 
−
RANDOM This feature plays the tracks in random order. To activate random play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play.
−
The SCAN function
SCAN samples all the tracks on the disc in the order they are recorded on the CD. To activate it, press and hold the SCAN button. You will see SCAN in the display. You will get a 10 second sampling of each track on the CD. Press the SCAN button again to get out of the system and play the last track sampled.
) to
To Stop Playing a CD Press the eject button ( remove the CD. If you eject the CD, but do not remove it from the slot, the system will automatically reload the CD after 10 seconds and put it in pause mode. To begin playing, press the CD button.
Press the AM or FM button to switch to the radio while a CD is playing. To play the CD, press the CD button.
If a tape is in the tape player, press the TAPE button to switch to the tape while a CD is playing. Press the CD button again to switch back to the CD player.
If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.
Protecting Discs For information on how to handle and protect discs, see page
134
Playing a Disc
Operating Optional CD Changer An optional six disc CD changer is available from your dealer. This disc changer uses the same controls used for the in-dash CD player or the radio.
Load the desired CDs in the magazine, and load the magazine in the changer according to the instructions that came with it.
−
To select the CD changer, press the
CD button. The CD and track
numbers will be displayed. To select
a different CD, use the preset 5
(DISC ) button to select the
previous disc, or the preset 6 (DISC
) button to select the next disc in
+
sequence. If you select an empty slot
in the magazine, the changer will
search for the next available CD to
load and play.
111
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘ï¼ï¼šï¼•ï¼•ã€€ï¼“1S9A64ï¼ã€€ï¼ï¼‘17 
Disc Player/Changer Error Messages
If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer.
CD Player Error
Message
CD Changer
Error
Message
112
Cause
Solution
Mechanical Error
High temperature
Focus Error
Cause
High temperature
No CD in magazine Focus Error
Mechanical Error
Press the CD eject button and pull out the CD. Check it for damage or deformation. If the CD cannot be pulled out, or the error message does not disappear after the CD is ejected, see your dealer. Will disappear when the temperature returns to normal. Press the eject button and pull out the CD. Check if it is inserted correctly in the CD player. Make sure the CD is not scratched or damaged.
Solution
Will disappear when the temperature returns to normal. Insert CDs in magazine. Press the CD eject button and pull out the CDs. Check for an error message, and insert the CDs again. If the message does not disappear or the CDs cannot be pulled out, see your dealer.
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼—ï¼ï¼‘3 14:24:47 31S9A64ï¼ã€€ï¼ï¼‘18 
U.S. LX and Canadian SE model
FF BUTTON
PWR/VOL KNOB
PLAY BUTTON
REW BUTTON
DOLBY BUTTON
TAPE EJECT BUTTON
REPEAT BUTTON
PROG BUTTON
TAPE SLOT
Playing a Tape
TAPE DIRECTION INDICATOR
SKIP BUTTONS
113
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘1:12 31S9A64ï¼ã€€ï¼ï¼‘19 
Playing a Tape
To Play a Tape The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Make sure the open side of the tape is facing right, then insert the tape most of the way into the slot. The system will pull the tape in the rest of the way and begin to play it.
â–²
The tape direction indicator in the display comes on to show you which side of the tape is playing. The indicates the side you inserted upward is now playing. If you want to play the other side, press the PROG button. When the player reaches the end of the tape, it will automatically reverse direction and play the other side.
114
*
Dolby noise reduction turns on when you insert a tape. The
indicator will light in the
display. If the tape was not recorded in Dolby, turn it off by pressing the
button. Dolby remains off until
you press the
button again.
*
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing Corporation. ‘‘DOLBY’’ and the double-D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
To Stop Playing a Tape To remove the tape, press the eject button. If you want to turn the player off, press the PWR/VOL knob or turn off the ignition. The tape will remain in the drive. When you turn the system back on, the tape will begin playing where it left off.
To switch to the radio or CD player while a tape is playing, press the AM, FM, or CD button. To change back to the tape player, press the TAPE button.
−
To rewind the tape,
Tape Search Functions FF/REW push the REW button. You will see REW in the display. To fast forward the tape, push the FF button. You will see FF displayed. Press the FF, REW, or PLAY button to take the system out of rewind or fast forward.
○ −
−
Press the
SKIP button to find the beginning of the current song or passage. Press the button to find the beginning of the next song or passage. When the system reaches the beginning of a song or passage, it begins to play it.
○ +
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘1:24 31S9A64ï¼ã€€ï¼ï¼‘ï¼’ï¼ã€€
−
Press the RPT button
REPEAT to continuously play a song or passage. You will see REPEAT displayed. The track will repeat until you press the RPT button again.
The skip and repeat
NOTE: functions use silent periods on the tape to find the end of a song or passage. These features may not work if there is almost no gap between selections, a high noise level, or a silent period in the middle of a selection.
Caring for the Tape and Player The tape player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use.
If you do not clean the tape player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Your dealer has a cleaning kit available.
Use 100-minute or shorter tapes. Tapes longer than that may break or jam the drive.
If the tape is loose, tighten it by turning the hub with a pencil or your finger. If the label is peeling off, remove it or it could cause the tape to jam in the player. Never try to insert a warped or damaged tape in
Playing a Tape
the player.
Store tapes in their cases to protect them from dust and moisture. Never place tapes where they will be exposed to direct sunlight, high heat, or high humidity. If a tape is exposed to extreme heat or cold, let it reach a moderate temperature before inserting it into the player.
Never try to insert foreign objects into the tape player.
If you see the error message ‘‘ ’’ on the display, press the tape eject button to remove the tape from the unit. Make sure the tape is not damaged. If the tape will not eject or the error message stays on after the tape ejects, take your vehicle to your dealer.
115
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘1:31 31S9A64ï¼ã€€ï¼ï¼‘21 
Playing the Radio
Canadian EX and EX-L models
U.S. EX and SE models
POWER/VOLUME KNOB
FM/AM BUTTON
STEREO INDICATOR
TUNE/SOUND KNOB
POWER/VOLUME KNOB
FM/AM BUTTON
STEREO INDICATOR
TUNE/SOUND KNOB
AUTO SELECT BUTTON
AUTO SELECT BUTTON
SCAN BUTTON
PRESET BUTTONS
SEEK BUTTONS
SCAN BUTTON PRESET BUTTONS
SEEK BUTTONS
116
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘1:41 31S9A64ï¼ã€€ï¼ï¼‘22 
Playing the Radio
To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on by pushing the PWR/VOL knob or the FM/AM button. Adjust the volume by turning the PWR/VOL knob.
The band and frequency that the radio was last tuned to is displayed. To change bands, press the FM/AM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.
OptionalforU.S.EXandSEmodels. XM satellite radio information is available on page
120
To Select a Station You can use any of five methods to find radio stations on the selected band: the preset buttons, and
TUNE, SEEK, SCAN,
AUTO SELECT
−
Use the TUNE knob to
TUNE tune the radio to a desired frequency. Turn the knob right to tune to a higher frequency, or left to tune to a lower frequency.
−
The SEEK function
SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press the release it.
○ ○+ −
SEEK button, then
or
−
The SCAN function
SCAN samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 5 seconds.
If you do nothing, the system will scan for the next strong station and play it for 5 seconds. When it plays a station you want to listen to, press the SCAN button again.
117
Main MenuTable of ContentsstTo turn off auto select, press the A. SEL button. This restores the presets you originally set.
ï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘1:52 31S9A64ï¼ã€€ï¼ï¼‘23 
Playing the Radio
−
If you are
AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.
Press the A. SEL button. ‘‘A.SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM and twelve FM stations in the preset buttons.
You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for every preset button.
If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described.
−
Each preset button can
Preset store one frequency on AM and two frequencies on FM.
1.
Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button.
2.
Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station.
3.
Pick a preset button and hold it until you hear a beep.
4.
Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
The preset frequencies will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.
118
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘2:ï¼ï¼’ 31S9A64ï¼ã€€ï¼ï¼‘24 
Playing the Radio
Adjusting the Sound BAL to-side strength of the sound.
Adjust the balance or side-
−
−
FAD front-to-back strength of the sound.
Adjust the fader or the
TRE − sound.
Adjust the treble in the
BAS
−
Adjust the bass in the sound.
Press the SOUND knob repeatedly to display the Bass (BAS), Treble (TRE), Fader (FAD), and Balance (BAL) settings.
Each mode is shown in the display as it changes. Turn the SOUND knob to adjust the setting to your liking. When the level reaches the center, you will see a ‘‘C’’ in the display. The system will return to the audio display about 5 seconds after you stop adjusting a mode.
Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page illuminates when the parking lights are on, even if the radio is off.
). The audio system
67
Radio Frequencies and Reception For information, see page
132
119
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘2:ï¼ï¼— 31S9A64ï¼ã€€ï¼ï¼‘25 
Playing the XM Satellite Radio (optional)
Optional on U.S. EX and SE models
CATEGORY MODE INDICATOR
DISPLAY BUTTON
TUNE KNOB
POWER/VOLUME KNOB
SCAN BUTTON
PRESET BUTTONS
SATELLITE RADIO BUTTON
PRESET BUTTONS
120
SEEK/SKIP BUTTONS
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘2:24 31S9A64ï¼ã€€ï¼ï¼‘26 
Playing the XM Satellite Radio (optional)
Satellite Digital Radio OptionalonU.S.EXandSEmodels Your vehicle is capable of receiving XM satellite radio anywhere in the United States except Hawaii and Alaska.
XM is a registered trademark of XM Satellite Radio, Inc. Satellite radio is available in U.S. models only.
To Play XM Satellite Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on:
Push any of the following: PWR/ VOL knob or the CD/XM button.
Turn the PWR/VOL knob to adjust the volume.
To Select a Channel When in the satellite radio mode,
you can use any of three methods to find channels: TUNE, SEEK/SKIP, and SCAN.
−
TUNE Turn the TUNE knob to change channel selection. Turn the knob right for higher numbered channels and left for lower numbered channels.
−
The SEEK/SKIP
SEEK/SKIP function selects the various categories in XM, such as Jazz/Blues, Rock, Classical, etc. Push the to change the category forward. Push the backward. To search for channels within a category, turn the TUNE knob clockwise.
to change the category
○ −
○ +
−
Press and release this
DISP button to change the display. The display will change in the following sequence: channel name, channel number, category, artist name, and music title.
Press and hold this button for more than 2 seconds to change the mode between the channel number and the category.
−
The scan function samples
SCAN all channels for 5 seconds. To activate the function, push the SCAN button. Push it again to get out of the sequence.
−
Each preset button can
Preset store one channel in XM1 and one in XM2.
1.
2.
3.
4.
Push the CD/XM button, you will see XM1 or XM2. Use the TUNE, SEEK or SCAN function to tune the radio to a desired channel. Pick a preset button and hold it until you hear a beep. Repeat steps 1 to 3 to store a total of six stations on XM1 and six on XM2.
121
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘2:31 31S9A64ï¼ã€€ï¼ï¼‘27 
Playing the XM Satellite Radio (optional)
Signal may be blocked by mountains or large obstacles to the south.
Signal is weaker in these areas.
SATELLITE
122
GROUND REPEATER
Satellite Radio Signals Satellite radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display.
The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.
Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator.
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘2:45 31S9A64ï¼ã€€ï¼ï¼‘28 
Playing the XM Satellite Radio (optional)
Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:
Driving on the south side of an east/west mountain road. Driving on the north side of a large commercial truck on an east/west road. Driving in tunnels. Driving on a road beside a vertical wall, steep cliff, or hill to the south of you. Driving on the lower level of a multi-tiered road. Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you.
There may also be other geographic situations that could affect satellite radio reception.
AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
Receiving Satellite Radio Service If your XM Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM satellite radio. With the ignition switch in the ACCESSORY (I) or the ON (II) position, push the PWR/VOL knob to turn on the audio system, and press the CD/XM button. A variety of music types and styles will play.
www.xmradio.com
If you decide to purchase XM satellite radio service, contact XM Radio at 1-800-852-9696. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, turn the TUNE
, or at
knob until ‘‘0’’ appears in the display. Your I.D. will appear in the display.
After you’ve registered with XM Radio, keep your audio system in the satellite radio mode while you wait for activation. This should take about 30 minutes.
While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, ‘‘category’’ or ‘‘CH’’ will appear in the display, and you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio.
123
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘2:51 31S9A64ï¼ã€€ï¼ï¼‘29 
Playing a Disc
Canadian EX and EX-L models
U.S. EX and SE models
LOAD BUTTON
RANDOM BUTTON
CD SLOT
CD BUTTON
CD EJECT BUTTON
LOAD BUTTON RANDOM BUTTON
CD SLOT
CD BUTTON
CD EJECT BUTTON
POWER/ VOLUME KNOB
POWER/ VOLUME KNOB
SKIP BUTTONS
SKIP BUTTONS
REPEAT BUTTON CD SELECT BUTTONS
REPEAT BUTTON CD SELECT BUTTONS
124
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘3:ï¼ï¼” 31S9A64ï¼ã€€ï¼ï¼‘3ï¼ã€€
To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or the ON(II) position.
You operate the CD player/CD changer with the same controls used for the radio. To select the CD player/CD changer, press the CD button. The number of the track playing is shown in the display. With the in-dash CD changer, the disc and track numbers are displayed. The system will continuously play a CD until you change modes.
You can also play 3-inch (8-cm) discs without using an adapter ring.
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
To play the radio when a CD is playing, press the AM/FM button. Press the CD button again to switch back to the CD player.
To play the tape when a CD is playing, insert a tape in the player. If a tape is in the player, press the TAPE button. Press the CD button again to switch back to the CD player.
If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.
Playing a Disc
LoadingCDsintheIn-dashCD Changer Your vehicle’s in-dash CD changer holds up to six discs.
1.
Press the LOAD button until you hear a beep and see ‘‘LOAD’’ in the display. To load only one CD, press and release the LOAD button.
2.
The disc number for an empty position is highlighted.
3.
Insert the disc into the CD slot when the green CD load indicator comes on. Insert it only about halfway; the drive will pull it in the rest of the way. You will see ‘‘BUSY’’ in the display while the CD load indicator turns red and blinks as the CD is loaded.
You cannot load and play 3-inch (8-cm) discs in this system.
CONTINUED
125
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘3:17 31S9A64ï¼ã€€ï¼ï¼‘31 
Playing a Disc
4.
When the CD load indicator turns green and ‘‘LOAD’’ appears in the screen again, insert the next CD in the slot. Do not try to insert a CD until ‘‘LOAD’’ appears. You could damage the audio unit.
5.
Repeat this until all six positions are loaded. If you are not loading all six positions, the system begins playing the last CD loaded.
You can also load a CD into an empty position while a CD is playing by pressing the appropriate preset button. The system stops playing the current CD and starts the loading sequence. It plays the CD just loaded.
FormodelswithXMRadio To listen to satellite radio when a CD is playing, press the CD/XM button.
126
−
DISP Press and release the DISP button to switch the display between the track and disc numbers and the elapsed time for the current CD.
○ +
−
Each time you press and
To Change or Select Tracks SKIP release the skip button the player skips forward to the beginning of the next track. Press and release the ○ − skip button to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.
To move rapidly within a track, press and hold the
skip button.
○ ○ + −
or
−
To continuously replay
REPEAT a track, press and release the RPT button. You will see RPT in the display. Press it again to turn it off.
−
RANDOM This feature plays the tracks in random order. To activate random play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play.
−
SCAN The SCAN function samples all the tracks on the selected disc in the order they are recorded on the CD. To activate it, press and hold the SCAN button. You will see SCAN in the display. You will get a 10 second sampling of each track on the selected CD. Press the SCAN button again to get out of the system and play the last track sampled.
To select a different CD, use the appropriate preset buttons (1 to 6).
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘3:28 31S9A64ï¼ã€€ï¼ï¼‘32 
To Stop Playing a CD Press the FM/AM or CD button to switch to the radio or satellite radio while a CD is playing. To play the CD, press the CD button again.
If a tape is in the tape player, press the TAPE button to switch to the tape while a CD is playing. Press the CD button again to switch back to the CD player/CD changer.
If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.
Removing CDs from the In-dash CD Changer To remove the disc currently in play, press the eject ( ) button. When a disc is removed from a slot, the system automatically begins the load sequence so you can load another CD in that position. If you do not remove the disc from the changer within 10 seconds, the system returns to the previous mode (AM/ FM or satellite radio). The disc will reload into the system and will remain there in a pause mode.
Playing a Disc
To remove a different CD from the changer, first select it with the appropriate preset button. When that CD begins playing, press the eject button. Continue pressing the eject button to remove all the discs from the changer.
You can also eject discs when the ignition switch is off. The disc that was last selected is ejected first.
Protecting Discs For information on how to handle and protect discs, see page
134
127
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘3:36 31S9A64ï¼ã€€ï¼ï¼‘33 
Disc Changer Error Messages
If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer.
CD Changer
Error
Message
Cause
Solution
FOCUS Error Mechanical Error
No CD in the CD changer
Press the CD eject button and pull out the CDs. Check for an error message, and insert the CDs again. If the message does not disappear or the CDs cannot be pulled out, see your dealer. Insert CDs.
128
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘3:45 31S9A64ï¼ã€€ï¼ï¼‘34 
Playing a Tape
Canadian EX and EX-L models
U.S. EX and SE models
POWER/ VOLUME KNOB
TAPE DIRECTION INDICATOR
TAPE EJECT BUTTON
TAPE DIRECTION INDICATOR
TAPE EJECT BUTTON
POWER/ VOLUME KNOB
TAPE SLOT
TAPE SLOT
DOLBY INDICATOR
DOLBY INDICATOR
REPEAT BUTTON
REPEAT BUTTON
PLAY BUTTON
PROG BUTTON
REW BUTTON
FF BUTTON
TAPE BUTTON
SKIP BUTTONS
DOLBY BUTTON
PLAY BUTTON
PROG BUTTON
REW BUTTON
FF BUTTON
TAPE BUTTON
SKIP BUTTONS
DOLBY BUTTON
129
Main MenuTable of Contentsstï¼ï¼•ï¼ï¼ï¼–ï¼ï¼“ï¼ã€€ï¼‘ï¼ï¼šï¼‘3:56 31S9A64ï¼ã€€ï¼ï¼‘35 
Playing a Tape
To Play a Tape The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Make sure the open side of the tape is facing right, then insert the tape most of the way into the slot. The system will pull the tape in the rest of the way and begin to play it.
â–²
The tape direction indicator in the display comes on to show you which side of the tape is playing. The indicates the side you inserted upward is now playing. If you want to play the other side, press the PROG button. When the player reaches the end of the tape, it will automatically reverse direction and play the other side.
130
*
Dolby noise reduction turns on when you insert a tape. The
indicator will light in the
display. If the tape was not recorded in Dolby, turn it off by pressing the
button. Dolby remains off until
you press the
button again.
*
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing Corporation. ‘‘DOLBY’’ and the double-D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
To Stop Playing a Tape To remove the tape, press the eject button. If you want to turn the player off, press the PWR/VOL knob or turn off the ignition. The tape will remain in the drive. When you turn the system back on, the tape will begin playing where it left off.
To switch to the radio, XM Radio (optional on U.S. EX and SE models), or CD changer while a Tape is playing, press the FM/AM or CD/ XM button. To change back to the tape player, press the TAPE button.
−