1. Turn the ignition switch to ON (w. 2. Go to the Maintenance info screen.
2 Displaying the Engine Oil Life and Maintenance Items P. 255
3. Press the SOURCE button.
u The oil life reset mode is displayed on the intelligent multi-information display.
4. Select YES with the (- button, then press the SOURCE button.
u The displayed maintenance items disappear, and the engine oil life display
returns to 100%.
u Any maintenance items that are necessary for your vehicle at the next
maintenance service will appear.
To cancel the oil life reset mode, select No, then press the SOURCE button.
13 CIVIC HYBRID-31TR26100.book 259 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Maintenance Under the Hood
Maintenance Items Under the Hood
Engine Oil Dipstick (Orange Loop)
Engine Oil Fill Cap
Washer Fluid (Blue Cap)
Brake Fluid (Black Cap)
Automatic Transmission (CVT) Fluid Dipstick (Yellow Loop)
12 Volt Battery
Radiator Cap
Engine Coolant Reservoir
QRG
TOC
Index
Home
259
13 CIVIC HYBRID-31TR26100.book 260 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduOpening the Hood
QRG
Opening the Hood
Hood Release Handle
Pull
1. Park the vehicle on a level surface, and set
1Opening the Hood
the parking brake.
2. Pull the hood release handle under the
lower left corner of the dashboard. u The hood will pop up slightly.
NOTICE Do not open the hood when the wiper arms are raised. The hood will strike the wipers, and may damage either the hood or the wipers.
When closing the hood, check that the hood is securely latched.
3. Push up the hood latch lever in the center of the hood to release the lock mechanism, and open the hood.
If the hood latch lever moves stiffly, or if you can open the hood without lifting the lever, the latch mechanism should be cleaned and lubricated.
Do not open the hood while the Auto Idle Stop function is activated.
Lever
Support Rod Grip
Clamp
TOC
Index
Home
260
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
13 CIVIC HYBRID-31TR26100.book 261 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduRecommended Engine Oil
1Recommended Engine Oil
Engine Oil Additives Your vehicle does not require oil additives. In fact, they may adversely affect the engine performance and durability.
Recommended Engine Oil
• Genuine Honda Motor Oil • Premium-grade 0W-20 detergent oil with an API Certification Seal on the
container.
Oil is a major contributor to your engine’s performance and longevity. If you drive the vehicle with insufficient or deteriorated oil, the engine may fail or be damaged.
This seal indicates the oil is energy conserving and that it meets the American Petroleum Institute’s latest requirements.
Use a Genuine Honda Motor Oil or another commercial engine oil of suitable viscosity for the ambient temperature as shown.
Ambient Temperature
â– Synthetic oil You may also use synthetic motor oil if it is labeled with the API Certification Seal and is the specified viscosity grade.
QRG
TOC
Index
Home
261
13 CIVIC HYBRID-31TR26100.book 262 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduOil Check
QRG
Oil Check We recommend that you check the engine oil level every time you refuel. Park the vehicle on level ground. Wait approximately three minutes after turning the engine off before you check the oil.
1Oil Check
If the oil level is near or below the lower mark, slowly add oil being careful not to overfill.
1. Remove the dipstick (orange loop).
2. Wipe the dipstick with a clean cloth or
paper towel.
3. Insert the dipstick back all the way into
its hole.
4. Remove the dipstick again, and check the level. It should be between the upper and lower marks. Add oil if necessary.
Upper Mark Lower Mark
TOC
Index
Home
262
13 CIVIC HYBRID-31TR26100.book 263 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduAdding Engine Oil
Adding Engine Oil
1. Unscrew and remove the engine oil fill cap.
1Adding Engine Oil
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten
it securely.
4. Wait for three minutes and recheck the
engine oil dipstick.
If any oil spills, wipe it up immediately. Spilled oil may damage the engine compartment components.
NOTICE Do not fill the engine oil above the upper mark. Overfilling the engine oil can result in leaks and engine damage.
Engine Oil Fill Cap
QRG
TOC
Index
Home
263
1Changing the Engine Oil and Oil Filter
NOTICE You may damage the environment if you do not dispose of the oil in a suitable way. If you are changing the oil by yourself, appropriately dispose of the used oil. Put the oil in a sealed container and take it to a recycling center. Do not throw the oil away into a garbage can or onto the ground.
13 CIVIC HYBRID-31TR26100.book 264 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduChanging the Engine Oil and Oil Filter
QRG
Changing the Engine Oil and Oil Filter You must change the engine oil and oil filter regularly in order to maintain the engine’s lubrication. The engine may be damaged if they are not changed regularly.
Change the oil and filter in accordance with the maintenance message on the intelligent multi-information display.
1. Run the engine until it reaches normal
operating temperature, and then turn the engine off.
2. Open the hood and remove the engine oil
fill cap.
3. Remove the bolts on the undercarriage
and slide the under cover backward, then remove.
4. Remove the drain bolt and washer from the bottom of the engine, and drain the oil into a suitable container.
Under Cover
Drain Bolt
Bolt
Washer
TOC
Index
Home
264
13 CIVIC HYBRID-31TR26100.book 265 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduChanging the Engine Oil and Oil Filter
5. Remove the oil filter and dispose of the
1Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil filter. You can buy this wrench from a dealer.
When installing the new oil filter, follow the instructions supplied with the oil filter.
Reinstall the engine oil fill cap. Start the engine. The low oil pressure indicator should go off within five seconds. If it does not, turn off the engine, and check your work.
Oil Filter
remaining oil.
6. Check that the filter gasket is not stuck to
the engine contact surface. u If it is stuck, you must detach it.
7. Wipe away dirt and dust adhering to the contact surface of the engine block, and install a new oil filter. u Apply a light coat of new engine oil to
the filter gasket.
8. Put a new washer on the drain bolt, then
reinstall the drain bolt. u Tightening torque:
29 lbf∙ft (39 N∙m, 4.0 kgf∙m)
9. Pour the recommended engine oil into
the engine. u Engine oil change capacity (including
filter): 3.8 US qt (3.6 L)
10. Reinstall the engine oil fill cap securely and
start the engine.
11. Run the engine for a few minutes, and
then check that there is no leak from the drain bolt or oil filter.
12. Stop the engine, wait for three minutes,
and then check the oil level on the dipstick. u If necessary, add more engine oil.
QRG
TOC
Index
Home
265
13 CIVIC HYBRID-31TR26100.book 266 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduEngine Coolant
QRG
Engine Coolant
Specified coolant: Honda Long Life Antifreeze/Coolant Type 2
1Engine Coolant
NOTICE If temperatures consistently below −22°F (−30°C) are expected, the coolant mixture should be changed to a higher concentration. Consult a dealer for more information.
If Honda antifreeze/coolant is not available, you may use another major brand non-silicate coolant as a temporary replacement. Check that it is a high quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
Do not add rust inhibitors or other additives to your vehicle’s coolant system. They may not be compatible with the coolant or with the engine components.
This coolant is premixed with 50% antifreeze and 50% water. Do not add any straight antifreeze or water.
We recommend you check the engine coolant level every time you refuel. Check the reserve tank first. If it is completely empty, also check the coolant level in the radiator. Add the engine coolant accordingly.
â– Reserve Tank
MAX
Reserve Tank
1. Check the amount of coolant in
the reserve tank.
MIN
TOC
Index
Home
266
2. If the coolant level is below the MIN mark,
add the specified coolant until it reaches the MAX mark.
3. Inspect the cooling system for leaks.
13 CIVIC HYBRID-31TR26100.book 267 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
â– Radiator
Radiator Cap
uuMaintenance Under the HooduEngine Coolant
1Radiator
3WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
NOTICE Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
1. Make sure the engine and
radiator are cool.
2. Turn the radiator cap counterclockwise and relieve any pressure in the cooling system. Do not push the cap down when turning.
3. Push down and turn the radiator cap
counterclockwise to remove it.
4. The coolant level should be up to the base
of the filler neck. Add coolant if it is low.
5 . Put the radiator cap back on, and
tighten it fully.
6. Pour coolant into the reserve tank until it reaches the MAX mark. Put the cap back on the reserve tank.
QRG
TOC
Index
Home
267
13 CIVIC HYBRID-31TR26100.book 268 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduTransmission Fluid
QRG
Transmission Fluid â– Continuously Variable Transmission (CVT) Fluid
Specified fluid: Honda CVTF (continuously variable transmission fluid)
Check the fluid level when the engine is at normal operating temperature.
1. Park on level ground, and start the engine.
2. Wait until the radiator fan starts and then
turn off the engine. u Perform step 3 after waiting for about 60
seconds (less than 90 seconds).
HOT Range
Upper Mark Lower Mark
3. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth.
4. Insert the dipstick all the way back into the transmission securely, as shown in the image.
5. Remove the dipstick and check the fluid
level. u It should be between the upper and
lower marks in the HOT range.
6. If the level is below the lower mark,
add fluid into the dipstick hole to bring it to the level between the upper and lower marks, and have your vehicle checked by a dealer immediately.
TOC
Index
Home
268
1Continuously Variable Transmission (CVT) Fluid
NOTICE Do not mix Honda CVTF with other transmission fluids. Using a transmission fluid other than Honda CVTF may adversely affect the operation and durability of your vehicle’s transmission, and damage the transmission. Any damage caused by using a transmission fluid that is not equivalent to Honda CVTF is not covered by Honda’s new vehicle warranty.
NOTICE Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
13 CIVIC HYBRID-31TR26100.book 269 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Brake Fluid
Specified fluid: Honda Heavy Duty Brake Fluid DOT 3
1Brake Fluid
uuMaintenance Under the HooduBrake Fluid
â– Checking the Brake Fluid
MAX
MIN
Check the fluid level several seconds after you turn the ignition switch to ON (w.
The fluid level should be between the MIN and MAX marks on the side of the reservoir.
Brake Reservoir
NOTICE Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.
If the specified brake fluid is not available, you should use only DOT 3 or DOT 4 fluid from a sealed container as a temporary replacement.
Using any non-Honda brake fluid can cause corrosion and decrease the longevity of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.
If the brake fluid level is at or below the MIN mark, have a dealer inspect for leaks or worn brake pads as soon as possible.
QRG
TOC
Index
Home
269
13 CIVIC HYBRID-31TR26100.book 270 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuMaintenance Under the HooduRefilling Window Washer Fluid
QRG
Refilling Window Washer Fluid Check the amount of window washer fluid using the washer fluid level gauge on the cap.
Level Gauge
If the level is low, fill the washer reservoir. Canadian models If the washer fluid is low, a message appears on the intelligent multi-information display (i-MID).
1Refilling Window Washer Fluid
NOTICE Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir. Antifreeze can damage your vehicle’s paint. A vinegar/water solution can damage the windshield washer pump.
Pour the washer fluid carefully. Do not overflow the reservoir.
TOC
Index
Home
270
13 CIVIC HYBRID-31TR26100.book 271 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Replacing Light Bulbs
Headlight Bulbs When replacing, use the following bulbs. High beam headlight: Low beam headlight:
60 W (HB3 for halogen bulb type) 51 W (HB4 for halogen bulb type)
â– High Beam Headlight
Bulb
Tab
Coupler
1. Push the tab to remove the coupler.
2. Rotate the old bulb to the left to remove.
3. Insert a new bulb into the headlight
assembly and turn it to the right.
4. Insert the coupler into the connector
of the bulb.
Continued
1Headlight Bulbs
NOTICE Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
The headlight aim is set by the factory, and does not need to be adjusted. However, if you regularly carry heavy items in the trunk, have the aiming readjusted at a dealer or by a qualified technician.
When replacing a halogen bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
The exterior lights’ inside lenses (headlights, brake lights, etc.) may fog temporarily after a car wash or while driving in the rain. This does not impact the exterior light function. However, if you see a large amount of water or ice accumulated inside the lenses, have your vehicle inspected by a dealer.
QRG
TOC
Index
Home
271
13 CIVIC HYBRID-31TR26100.book 272 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuReplacing Light BulbsuDaytime Running Light Bulbs
QRG
â– Low Beam Headlights
Clip
Passenger’s side 1. Remove the holding clip using a flat-tip
screwdriver, then remove the upper part of the windshield washer reservoir.
1Low Beam Headlights
Insert a flat-tip screwdriver, lift and remove the central pin to remove the clip.
Central pin
Driver’s and passenger’s side 2. Push the tab to remove the coupler.
3. Rotate the old bulb to the left to remove.
4. Insert a new bulb into the headlight
assembly and turn it to the right.
5. Insert the coupler into the connector of
Insert the clip with the central pin raised, and push until it is flat.
Push until the pin is flat.
Coupler
the bulb.
Daytime Running Light Bulbs Daytime running light bulbs are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
TOC
Index
Home
272
13 CIVIC HYBRID-31TR26100.book 273 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuReplacing Light BulbsuFront Turn Signal/Parking/Side Marker Light Bulbs
Front Turn Signal/Parking/Side Marker Light Bulbs When replacing, use the following bulbs. Front Turn Signal/Parking/Side Marker Light: 28/8 W
Inner Fender
1. Turn the steering wheel all the way to the opposite side from the light being replaced. Passenger side: Turn the steering wheel to the left. Driver side: Turn the steering wheel to the right.
2. Remove the holding clips, and pull the inner
fender back.
1Front Turn Signal/Parking/Side Marker Light Bulbs
When removing the clip, insert a flat-tip screwdriver, then lift and remove the clip.
QRG
Clip
Socket
3. Turn the socket to the left and remove it,
then remove the old bulb.
Insert the clip with the pin raised, and push until it is flat.
4. Insert a new bulb.
Push until the pin is flat
Clip
Bulb
Side Turn Signal/Emergency Indicator Light Bulbs Door mirrors have the side turn lights. Have an authorized Honda dealer inspect and replace the light assembly.
TOC
Index
Home
273
13 CIVIC HYBRID-31TR26100.book 274 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuReplacing Light BulbsuRear Turn Signal Light Bulbs
QRG
Rear Turn Signal Light Bulbs When replacing, use the following bulbs. Rear Turn Signal Light: 21 W (Amber)
Lining
1. Remove the holding clips using a flat-tip
screwdriver, then pull the lining back.
1Rear Turn Signal Light Bulbs
When removing the clip, insert a flat-tip screwdriver, then lift and remove the clip.
Clip
Clip
2. Turn the socket to the left and remove it.
Remove the old bulb.
3. Insert a new bulb.
Insert the clip with the pin raised, and push until it is flat.
Push until the pin is flat
Bulb
Socket
Brake/Taillight and Rear Side Maker Bulbs Brake/rear taillight and rear side marker bulbs are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
TOC
Index
Home
274
13 CIVIC HYBRID-31TR26100.book 275 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuReplacing Light BulbsuBack-Up Light Bulbs
Back-Up Light Bulbs When replacing, use the following bulbs. Back-Up Light: 16 W
Lining Fastener
Clip
Bulb
1. Remove the screw from the center of the fastener using a Phillips-head screwdriver.
2. Remove the holding clips using a flat-tip
screwdriver, then pull the lining back.
2 Rear Turn Signal Light Bulbs P. 274
3. Turn the socket to the left and remove it.
4. Remove the old bulb and insert a new bulb.
Socket
Taillight Bulbs Taillight bulbs in the trunk lid are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
QRG
TOC
Index
Home
275
13 CIVIC HYBRID-31TR26100.book 276 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuReplacing Light BulbsuRear License Plate Light Bulbs
QRG
Rear License Plate Light Bulbs When replacing, use the following bulbs. Rear License Plate Light: 5 W
Lining Fastener
Clip
Bulb
1. Remove the screw from the center of the fastener using a Phillips-head screwdriver.
2. Remove the holding clips using a flat-tip
screwdriver, then pull the lining back.
2 Rear Turn Signal Light Bulbs P. 274
3. Remove the license plate light assembly by
squeezing the tabs on both sides of the socket.
4. Remove the old bulb and insert a new bulb.
Socket
High-Mount Brake Light Bulbs High-mount brake light bulbs are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
TOC
Index
Home
276
13 CIVIC HYBRID-31TR26100.book 277 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Checking and Maintaining Wiper Blades
Checking Wiper Blades If the wiper blade rubber has deteriorated, it will leave streaks and the metal wiper arm may scratch the window glass.
Changing the Wiper Blade Rubber
1. Lift the driver side wiper arm first, then the
passenger side.
1Changing the Wiper Blade Rubber
NOTICE Avoid dropping the wiper arm; it may damage the windshield.
Lock Tab
2. Place a cloth on the edge of the lock tab. Push the lock tab up with a flat-tip screw driver.
3. Slide the blade from the wiper arm.
Continued
QRG
TOC
Index
Home
277
13 CIVIC HYBRID-31TR26100.book 278 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining Wiper BladesuChanging the Wiper Blade Rubber
4. Slide the wiper blade out from its holder by
pulling the tabbed end out.
Blade
Top
Retainer
Blade
Indent
Tab
5. Remove the retainers from the rubber blade
that has been removed, and mount to a new rubber blade. u Correctly align the rubber protrusion and
the retainer grooves.
6. Slide the new wiper blade onto the holder
from the bottom end. u The tab on the holder should fit in the
indent of the wiper blade.
7. Slide the wiper blade onto the wiper arm,
then push down the lock tab.
8. Lower the passenger side wiper arm first,
then the driver side.
QRG
TOC
Index
Home
278
13 CIVIC HYBRID-31TR26100.book 279 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Checking and Maintaining Tires
Checking Tires To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inflated.
■Inflation guidelines Properly inflated tires provide the best combination of handling, tread life, and comfort. Refer to the driver’s doorjamb label or specification’s page for the specified pressure.
Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from overheating.
Overinflated tires make your vehicle ride harshly, are more prone to road hazards, and wear unevenly.
Every day before you drive, look at each of the tires. If one looks lower than the others, check the pressure with a tire gauge.
At least once a month or before long trips, use a gauge to measure the pressure in all tires, including the spare. Even tires in good condition can lose 1 to 2 psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm2) per month.
■Inspection guidelines Every time you check inflation, also examine the tires and valve stems. Look for: • Bumps or bulges on the side or in the tread. Replace the tire if you find any cuts,
splits, or cracks in the side of the tire. Replace it if you see fabric or cord.
• Remove any foreign objects and inspect for air leaks. • Uneven tread wear. Have a dealer check the wheel alignment. • Excessive tread wear.
2 Wear Indicators P. 284
• Cracks or other damage around valve stem.
1Checking Tires
3WARNING
Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
Measure the air pressure when tires are cold. This means the vehicle has been parked for at least three hours, or driven less than 1 mile (1.6 km). If necessary, add or release air until the specified pressure is reached.
If checked when hot, tire pressure can be as much as 4–6 psi (30–40 kPa, 0.3–0.4 kgf/cm2) higher than if checked when cold.
Have a dealer check the tires if you feel a consistent vibration while driving. New tires and any that have been removed and reinstalled should be properly balanced.
QRG
TOC
Index
Home
279
13 CIVIC HYBRID-31TR26100.book 280 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining TiresuTire and Loading Information Label
QRG
Tire and Loading Information Label The label attached to the driver’s doorjamb provides necessary tire and loading information.
Label Example
1Tire and Loading Information Label
The tire and loading information label attached to the driver’s doorjamb contains: a The number of people your vehicle can carry. b The total weight your vehicle can carry. Do not c The original tire sizes for front, rear, and spare. d The proper cold tire pressure for front, rear, and
exceed this weight.
spare.
Tire Labeling
Example
Tire Size Tire Identification Number (TIN)
Maximum Tire Load
Maximum Tire Pressure
Tire Size
The tires that came on your vehicle have a number of markings. Those you should be aware of are described below.
1Tire Size
Following is an example of tire size with an explanation of what each component means. P195/65 R15 89S P: 195: Tire width in millimeters. 65: Aspect ratio (the tire’s section height as a
Vehicle type (P indicates passenger vehicle).
â– Tire Size Whenever tires are replaced, they should be replaced with tires of the same size.
S:
percentage of its width). Tire construction code (R indicates radial).
R: 15: Rim diameter in inches. 89:
Load index (a numerical code associated with the maximum load the tire can carry). Speed symbol (an alphabetical code indicating the maximum speed rating).
TOC
Index
Home
280
13 CIVIC HYBRID-31TR26100.book 281 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
â– Tire Identification Number (TIN) The tire identification number (TIN) is a group of numbers and letters that look like the example in the side column. TIN is located on the sidewall of the tire.
■Glossary of Tire Terminology Cold Tire Pressure – The tire air pressure when the vehicle has been parked for at least three hours or driven less than 1 mile (1.6 km).
Load Rating – Means the maximum load that a tire is rated to carry for a given inflation pressure.
Maximum Inflation Pressure – The maximum tire air pressure that the tire can hold.
Maximum Load Rating – Means the load rating for a tire at the maximum permissible inflation pressure for that tire.
Recommended Inflation Pressure – The cold tire inflation pressure recommended by the manufacturer.
Treadwear Indicators (TWI) – Means the projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.
uuChecking and Maintaining TiresuTire Labeling
1Tire Identification Number (TIN)
DOT B97R FW6X 2209
DOT: This indicates that the tire meets all
requirements of the U.S. Department of Transportation.
B97R: Manufacturer’s identification mark. FW6X: Tire type code. 22 09: Date of manufacture.
Year Week
QRG
TOC
Index
Home
281
13 CIVIC HYBRID-31TR26100.book 282 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining TiresuDOT Tire Quality Grading (U.S. Vehicles)
DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also to Department of these gradings.
Transportation (DOT) standards. The following explains
graded for treadwear, traction, and temperature performance according
â– Uniform Tire Quality Grading
Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
â– Treadwear
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
1Uniform Tire Quality Grading
For example:
Treadwear 200
Traction AA
Temperature A
All passenger car tires must conform to Federal Safety Requirements in addition to these grades.
QRG
TOC
Index
Home
282
13 CIVIC HYBRID-31TR26100.book 283 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining TiresuDOT Tire Quality Grading (U.S. Vehicles)
â– Traction
The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance.
â– Temperature
The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
1Traction
Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
1Temperature
Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
QRG
TOC
Index
Home
283
13 CIVIC HYBRID-31TR26100.book 284 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining TiresuWear Indicators
QRG
Wear Indicators
Example of a Wear Indicator mark
The groove where the wear indicator is located is 1/16 inch (1.6 mm) shallower than elsewhere on the tire. If the tread has worn so that the indicator is exposed, replace the tire. Worn out tires have poor traction on wet roads.
Tire Service Life The life of your tires is dependent on many factors, including driving habits, road conditions, vehicle loading, inflation pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use).
In addition to regular inspections and inflation pressure maintenance, it is recommended that you have annual inspections performed once the tires reach five years old. All tires, including the spare, should be removed from service after 10 years from the date of manufacture, regardless of their condition or state of wear.
TOC
Index
Home
284
13 CIVIC HYBRID-31TR26100.book 285 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining TiresuTire and Wheel Replacement
Tire and Wheel Replacement Replace your tires with radials of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a different size or construction can cause the ABS and vehicle stability assist (VSA®) system to work incorrectly.
It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.
Make sure that the wheel’s specifications match those of the original wheels.
U.S. models only If you replace a wheel, only use TPMS specified wheels approved for your vehicle.
1Tire and Wheel Replacement
3WARNING
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in this owner’s manual.
QRG
TOC
Index
Home
285
13 CIVIC HYBRID-31TR26100.book 286 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuChecking and Maintaining TiresuTire Rotation
QRG
Tire Rotation Rotating tires according to the maintenance messages on the intelligent multi- information display helps to distribute wear more evenly and increase tire life.
â– Tires without rotation marks
Rotate the tires as shown here.
Front
â– Tires with rotation marks
Rotate the tires as shown here.
1Tire Rotation
Tires with directional tread patterns should only be rotated front to back (not from one side to the other). Directional tires should be mounted with the rotation indication mark facing forward, as shown below.
Front
Direction Mark
Front
TOC
Index
Home
286
13 CIVIC HYBRID-31TR26100.book 287 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Winter Tires If driving on snowy or frozen roads, mount all season marked M+S tires, snow tires, or tire chains; reduce speed; and maintain sufficient distance between vehicles when driving.
Be particularly careful when operating the steering wheel or brakes to prevent skidding.
Use tire chains, snow tires, or all season tires when necessary or according to the law.
When mounting, refer to the following points.
For winter tires: • Select the size and load ranges that are the same as the original tires.
• Mount the tires to all four wheels.
For tire chains: • Install them on the front tires only.
• Because your vehicle has limited tire clearance, we strongly recommend using the
chains listed below:
Cable-type: SCC Radial Chain SC1030
• Follow the chain manufacturer’s instruction when installing. Mount them as
tightly as you can.
• Check that the chains do not touch the brake lines or suspension.
• Drive slowly.
uuChecking and Maintaining Tires uWinter Tires
1Winter Tires
3WARNING
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.
Follow all instructions in this owner’s manual regarding the selection and use of tire chains.
NOTICE Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.
When tire chains are mounted, follow the chain manufacturer’s instructions regarding vehicle operational limits.
QRG
TOC
Index
Home
287
13 CIVIC HYBRID-31TR26100.book 288 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
12 Volt Battery
QRG
Checking the 12 Volt Battery Check the battery condition monthly and check the terminals for corrosion.
112 Volt Battery
If your vehicle’s battery is disconnected or goes dead: • The audio system is disabled.
2 Reactivating the audio system P. 146
• The clock resets.
2 Setting the Clock P. 104
• The navigation system * is disabled.
2 Refer to the navigation system manual
Charging the Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (-) cable first, and reconnect it last.
TOC
Index
Home
288
* Not available on all models
3WARNING
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.
When conducting any battery maintenance, wear protective clothing and a face shield, or have a skilled technician do it.
WARNING: Battery post, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.
When you find corrosion, clean the battery terminals by applying a baking powder and water solution. Clean the terminals with a damp towel. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion.
13 CIVIC HYBRID-31TR26100.book 289 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Remote Transmitter Care
Replacing the Button Battery If the indicator does not come on when the button is pressed, replace the battery.
1Replacing the Button Battery
QRG
Keypad
Battery
Battery type: CR1616
1. Unscrew the cover with a small Phillips- head screwdriver. Press a button to pry open the transmitter.
NOTICE An improperly disposed of battery can damage the environment. Always confirm local regulations for battery disposal.
Replacement batteries are commercially available or at a dealer.
Screw
Tab
2. Open the keypad.
u Separate the inner cover from the
keypad by releasing the two tabs on the cover.
3. Make sure to replace the battery with the
correct polarity.
TOC
Index
Home
289
13 CIVIC HYBRID-31TR26100.book 290 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Climate Control System Maintenance
QRG
Dust and Pollen Filter The Climate Control system is equipped with a dust and pollen filter that collects pollen, dust, and other debris in the air. The Maintenance MinderTM messages will let you know when to replace the filter.
We recommend that you replace the dust and pollen filter sooner when using your vehicle in areas with high concentrations of dust.
1Dust and Pollen Filter
If the airflow from the climate control system deteriorates noticeably, and the windows fog up easily, the filter may need to be replaced. Please contact a dealer for replacement.
TOC
Index
Home
290
13 CIVIC HYBRID-31TR26100.book 291 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Cleaning
Interior Care Use a damp cloth with a mixture of mild detergent and warm water to remove dirt. Use a clean cloth to remove detergent residue.
1Interior Care
Do not spill liquids inside the vehicle.
QRG
â– Cleaning Seat Belts Use a soft brush with a mixture of mild soap and warm water to clean the seat belts. Let the belts air dry. Wipe the openings of the seat belt anchors using a clean cloth.
Opening
Continued
Electrical devices and systems may malfunction if liquids are splashed on them.
Do not use silicone based sprays on electrical devices such as audio devices and switches.
Doing so may cause the items to malfunction or a fire inside the vehicle.
If a silicone based spray is inadvertently used on electrical devices, consult a dealer.
Depending on their composition, chemicals and liquid aromatics may cause discoloration, wrinkles, and cracking to resin-based parts and textiles.
Do not use alkali solvents or organic solvents such as benzene or gasoline.
After using chemicals, make sure to gently wipe them off using a dry cloth.
Do not place used cloths on top of resin based parts or textiles for long periods of time without washing.
TOC
Index
Home
291
1Floor Mats
If you use any floor mats that were not originally provided with your vehicle, make sure they are designed for your specific vehicle, fit correctly, and are securely anchored by the floor anchors. Position the rear seat floor mats properly. If they are not properly positioned, the floor mats can interfere with the front seat functions.
13 CIVIC HYBRID-31TR26100.book 292 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuCleaninguInterior Care
QRG
â– Floor Mats
Unlock
Lock
The driver’s floor mat hooks over the floor anchors, which keep the mat from sliding forward. To remove a mat for cleaning, turn the anchor knobs to the unlock position. When reinstalling the mat after cleaning, turn the knobs to the lock position.
Do not put additional floor mats on top of the anchored mat.
â– Maintaining Genuine Leather* Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral soap solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.
* Not available on all models
TOC
Index
Home
292
13 CIVIC HYBRID-31TR26100.book 293 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Exterior Care Dust off the vehicle body after you drive.
Regularly inspect your vehicle for scratches on painted surfaces. A scratch on a painted surface can result in body rust. If you find a scratch, promptly repair it.
■Washing the Vehicle Wash the vehicle regularly. Wash more frequently when driving in the following conditions: • If driving on roads with road salt.
• If driving in coastal areas.
• If tar, soot, bird droppings, insects, or tree sap are stuck to painted surfaces.
uuCleaninguExterior Care
QRG
1Washing the Vehicle
Do not spray water into the air intake vents or engine compartment. It can cause a malfunction.
â– Using an Automated Car Wash Make sure to follow the instructions indicated on the automated car wash:
Air Intake Vents
• Remove the audio antenna.
• Fold in the door mirrors.
â– Using High Pressure Cleaners
• Keep sufficient distance between the cleaning nozzle and the vehicle body.
• Take particular care around the windows. Standing too close may cause water to
enter the vehicle interior. Do not spray water into the engine compartment.
Continued
TOC
Index
Home
293
13 CIVIC HYBRID-31TR26100.book 294 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
uuCleaninguExterior Care
QRG
■Applying Wax A good coat of automotive body wax helps protect your vehicle’s paint from the elements. Wax will wear off over time and expose your vehicle’s paint to the elements, so reapply as necessary.
1Applying Wax
NOTICE Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your vehicle. Wipe up spills immediately.
â– Maintaining the Bumpers and Other Resin Coated Parts If you get gasoline, oil, engine coolant, or battery fluid on resin coated parts, they may be stained or the coating may peel. Promptly wipe it away using a soft cloth and clean water.
1Maintaining the Bumpers and Other Resin Coated Parts
Ask a dealer about the correct coating material when you want to repair the painted surface of the parts made of resin.
â– Cleaning the Window Wipe using a glass cleaner.
TOC
â– Maintaining Aluminum Wheels Aluminum is susceptible to deterioration caused by salt and other road contaminants. Use a sponge and mild detergent to wipe away promptly. Be careful not to use harsh chemicals (including some commercial wheel cleaners) or a stiff brush. They can damage the clear coat of the aluminum alloy wheels that helps keep the aluminum from corroding and tarnishing.
1Cleaning the Window
Wires are mounted to the inside of the rear window. Wipe along the same direction as the wires with a soft cloth so as not to damage them.
Index
Home
294
13 CIVIC HYBRID-31TR26100.book 295 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Handling the Unexpected
QRG
This chapter explains how to handle unexpected troubles.
Tools
Types of Tools.................................. 296
If a Tire Goes Flat
Temporarily Repairing a Flat Tire....... 297
Changing a Flat Tire......................... 305
Engine Does Not Start
Checking the Engine........................ 311
Jump Starting.................................... 312
Shift Lever Does Not Move.............. 314
Overheating
How to Handle Overheating............. 315
Indicator, Coming On/Blinking
317
If the Low Oil Pressure Indicator
Comes On....................................
If the 12 Volt Battery Charging
System Indicator Comes On ...........
If the Malfunction Indicator Lamp
Comes On or Blinks.........................
If the Brake System Indicator (Red)
Comes On..........................................
319
If the EPS System Indicator Comes On.. 319
If the IMA Indicator Comes On......... 320
317
318
If the Low Tire Pressure/TPMS Indicator
Comes On or Blinks ....................... 320
Fuses
Fuse Locations ................................. 321
Inspecting and Changing Fuses........ 323
Emergency Towing........................... 324
Index
Home
295
13 CIVIC HYBRID-31TR26100.book 296 ページ ï¼’ï¼ï¼‘2年12月18日 ç«æ›œæ—¥ã€€åˆå¾Œï¼’時59分
Tools
QRG
Types of Tools Models with optional compact spare
Wheel Nut Wrench/
Jack Handle
Jack