2011 Honda Civic Coupe Owners Manual

Canadian DX-G with manual transmission

P195/65R15 89S

LX, SE, EX, EX-L

P205/55R16 89H

Si

P215/45R17 87V

OptionalforU.S.Si 215/45ZR17 91W

(all season tire)

(summer tire)

367

for information about

See page DOT Tire Quality Grading, and page 369
information.

for tire size and labeling

330

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

SummerTires Simodelonly If your vehicle is equipped with summer tires, be aware that these tires are not designed for winter driving conditions. For more information, consult your dealer.

10/06/24 17:05:25 31SVA650_336

Tires

SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.

TireChains Mount tire chains on your tires when required by driving conditions or local laws. Install them only on the front tires.

Because your vehicle has limited tire clearance, Honda strongly recommends using the chains listed below, made by Security Chain Company (SCC).

When installing chains, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

DX, Canadian DX-G Cable-type: SCC Radial Chain

SC1030

LX, SE, EX, EX-L, Si Cable-type: SCC Radial Chain

SC1032

CONTINUED

331

10/06/24 17:05:30 31SVA650_337

Tires

Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.

Follow all instructions in this owner’s manual regarding the selection and use of tire chains.

Wheels Clean the wheels as you would the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.

Ifequipped Aluminum alloy wheels have a protective clear-coat that keeps the aluminum from corroding and tarnishing. Cleaning the wheels with harsh chemicals (including some commercial wheel cleaners) or a stiff brush can damage the clear-coat. To clean the wheels, use a mild detergent and a soft brush or sponge.

332

10/06/24 17:05:36 31SVA650_338

TEST INDICATOR WINDOW

TEST INDICATOR WINDOW

DX, DX-G, LX, SE, EX, EX-L

Si

Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

The location of the test indicator window varies between manufacturers.

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent further corrosion.

Checking the Battery

If additional battery maintenance is needed, see your dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

CONTINUED

333

If your vehicle’s battery is disconnected or goes dead, the audio system may disable itself. The next time you turn on the radio, you will see ‘‘ENTER CODE’’ in the frequency display. Use the preset buttons to enter the code (see page 221

).

Onmodelswithnavigationsystem The navigation system will also disable itself. The next time you turn on the ignition switch, the system will require you to enter a PIN before it can be used. Refer to the navigation system manual.

If your vehicle’s battery is disconnected, or goes dead, the time setting may be lost. To reset the time, see page

222

10/06/24 17:05:41 31SVA650_339

Checking the Battery

If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.

) cable first, and

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled technician do the battery maintenance.

334

10/06/24 17:05:50 31SVA650_340

If you need to park your vehicle for an extended period (more than 1
month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc., are completely dry.

Leave the parking brake off. Put the transmission in reverse (manual) or Park (automatic).

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Disconnect the battery.

Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.

Vehicle Storage

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

If possible, periodically run the engine until it reaches full operating temperature (the cooling fans cycle on and off twice). Preferably, do this once a month.

335

10/06/24 17:05:54 31SVA650_341

Interior Care

Leather Ifequipped Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral wool detergent solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.

336

10/06/24 17:05:57 31SVA650_342

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Fuses Fuse Locations Emergency Towing

...................... .................... ............. ................................ .............. ......... .......... ....... ............... .............................................. .............................. ......................

. 338
. 339
. 343
. 345
. 347
. 349
. 349
. 350
. 351
. 352
. 356
. 358

337

10/06/24 17:06:07 31SVA650_343

Compact Spare Tire

Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can.

Check the air pressure of the compact spare tire every time you check the other tires. It should be inflated to:

60 psi (420 kPa , 4.2 kgf/cm )

Follow these precautions:

Never exceed 50 mph (80 km/h).

This tire gives a harsher ride and less traction on some road surfaces. Use greater caution while driving.

338

Do not mount tire chains on the compact spare tire.

Do not use your compact spare tire on another vehicle unless it is the same make and model.

INDICATOR LOCATION MARK

OnSimodel

Do not use a compact spare tire mounted on a front wheel; it will damage the limited slip differential (see page

339

).

AllU.S.models

The low tire pressure indicator comes on and stays on after you replace the flat tire with the compact spare tire. After several miles (kilometers) driving with the compact spare tire, the TPMS indicator comes on and the low tire pressure indicator goes off.

TREAD WEAR INDICATOR

Replace the tire when you can see the tread wear indicator bars. The replacement tire should be the same size and design, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.

10/06/24 17:06:17 31SVA650_344

If you have a flat tire while driving, pull over safely. Drive slowly along the shoulder until you get to an area far away from traffic lanes.

The compact spare tire is smaller than a standard tire, and it will affect the vehicle’s handling. Drive cautiously when the spare is mounted on your vehicle.

OnSimodelonly The size difference may also cause damage to the differential, so do not mount the compact spare on the front. If either front tire goes flat, remove the rear tire on that same side, mount the compact spare tire on the rear, then mount the rear tire on the front.

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

1.

2.

Park the vehicle on firm, level, and non-slippery ground. Put the transmission in Park (automatic) or reverse (manual). Apply the parking brake.

Turn on the hazard warning lights, and turn the ignition switch to the LOCK (0) position. Have all passengers get out of the vehicle while you change the tire.

Changing a Flat Tire

JACK

TOOL CASE

TRUNK FLOOR

SPARE TIRE

3.

Open the trunk. Raise the trunk floor by lifting up on the back edge.

4.

Take the tool kit case out of the trunk.

5.

Unscrew the wing bolt, and take the spare tire out of its well.

CONTINUED

339

10/06/24 17:06:24 31SVA650_345

Changing a Flat Tire

JACKING POINTS

6.

CanadianDX-Gmodel Remove the center cap from the wheel with the extension.

WHEEL NUT WRENCH

7.

Loosen each wheel nut 1/2 turn with the wheel nut wrench.

8.

Place the jack under the jacking point nearest the tire you need to change. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch.

340

10/06/24 17:06:32 31SVA650_346

Changing a Flat Tire

WHEEL NUTS

WHEEL NUT WRENCH

EXTENSION

WHEEL NUTS WHEEL COVER

BRAKE HUB

9.

Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground.

10.

Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.

U.S.DXandLXmodels Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts.

11.

Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.

CONTINUED

341

10/06/24 17:06:40 31SVA650_347

Changing a Flat Tire

12.

Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten the wheel nuts fully.

13.

Lower the vehicle to the ground, and remove the jack.

14.

Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.

Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)

15.

OnEX,EX-LandSimodelsintheU.S., andSE,EX-LandSimodelsinCanada Remove the center cap from the flat tire.

342

10/06/24 17:06:51 31SVA650_348

SPACER CONE

WING BOLT

For compact spare tire

For normal tire

16.

Place the flat tire face down in the spare tire well.

17.

Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.

18.

Secure the flat tire by screwing the wing bolt back into its hole.

19.

Store the jack and tools in the tool kit case. Place the tool kit case in the center of the flat tire.

Changing a Flat Tire, If the Engine Won’t Start

Loose items can fly around the interior in a crash and could seriously injure the occupants.

Store the wheel, jack, and tools securely before driving.

20.

Store the wheel cover or center cap in the trunk. Make sure it does not get scratched or damaged.

21.

Lower the trunk floor, then close the trunk lid.

22.

OnallU.S.models Your vehicle’s original tire has a tire pressure monitoring system sensor. To replace a tire, refer to Changing a Tire with TPMS page

286

).

(see

If the Engine Won’t Start Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position:

You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

343

10/06/24 17:07:01 31SVA650_349

If the Engine Won’t Start

Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to the START (III) position, you do not hear the normal noise of the engine trying to start. You may hear a clicking sound, a series of clicks, or nothing at all. Check these things:

Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or neutral.

Turn the ignition switch to the ON (II) position. Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting

on page

345

344

Turn the ignition switch to the START (III) position. If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem. See Emergency Towing

on page

358

If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the battery and terminal connec- tions (see page then try jump starting the vehicle from a booster battery (see page 345

). You can

333

).

The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster

than normal, when you turn the ignition switch to the START (III) position, but the engine does not run.

Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page ).

80

Are you using the proper starting Starting the procedure? Refer to Engine 270

on page

Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page

352

).

If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page

Emergency 358

10/06/24 17:07:09 31SVA650_350

Although this seems like a simple procedure, you should take several precautions.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

You cannot start a vehicle with an automatic transmission by pushing or pulling it.

To jump start your vehicle: 1.

Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte. If it seems slushy or frozen, do not try jump starting until it thaws.

If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.

2.

Turn off all the electrical accessories: heater, A/C, audio system, lights, etc. Put the transmission in neutral (manual) or Park (automatic), and set the parking brake.

Jump Starting

DX, DX-G, LX, SE, EX, EX-L

BOOSTER BATTERY

The numbers in the illustrations show you the order to connect the jumper cables.

CONTINUED

345

10/06/24 17:07:18 31SVA650_351

Jump Starting

Si

DX, DX-G, LX, SE, EX, EX-L

Si

BOOSTER BATTERY

3.

＋

) terminal on your

Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the ＋ booster battery.

6.

Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.

4.

−

Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.

5.

If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.

346

10/06/24 17:07:26 31SVA650_352

7.

Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery.

Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.

Jump Starting, If the Engine Overheats

If the Engine Overheats The reading of the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).

If the vehicle overheats, you should take immediate action. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.

Driving with the temperature gauge reading at the red mark can cause serious damage to the engine.

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

1.

Safely pull to the side of the road. Put the transmission in neutral (manual) or Park (automatic), and set the parking brake. Turn off all accessories, and turn on the hazard warning lights.

2.

If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.

CONTINUED

347

10/06/24 17:07:34 31SVA650_353

If the Engine Overheats

3.

If you do not see steam or spray, leave the engine running and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint, then continue driving.

4.

If the temperature gauge stays at the red mark, turn off the engine.

5.

Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 358

on page

6.

If you don’t find an obvious leak, check the coolant level in the radiator reserve tank (see page ). Add coolant if the level is 257
below the MIN mark.

348

7.

If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the reading reaches the middle of the temperature gauge, or lower, before checking the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

8.

Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.

9.

Start the engine, and set the temperature control dial to maximum heat. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

10.

11.

Put the radiator cap back on tightly. Run the engine, and check the temperature gauge. If it goes back to the red mark, the engine needs repair (see on page Towing

Emergency 358

).

If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

10/06/24 17:07:43 31SVA650_354

Low Oil Pressure Indicator

This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action.

Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.

1.

2.

3.

4.

Low Oil Pressure Indicator, Charging System Indicator

Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.

Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.

255

If necessary, add oil to bring the level back to the full mark on the dipstick (see page

300

).

Start the engine, and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving (see 358

Emergency Towing ).

on page

Charging System Indicator

If the charging system indicator comes on brightly when the engine is running, the battery is not being charged.

Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows. Keep the engine running; starting the engine will discharge the battery rapidly.

Go to a service station or garage where you can get technical assistance.

349

10/06/24 17:07:51 31SVA650_355

Malfunction Indicator Lamp

If the indicator comes on while driving, it means one

of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.

If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. You will also see a ‘‘CHECK FUEL CAP’’ message on the information display. Tighten the cap until it clicks at least once. Tightening the cap will not turn the indicator off immediately; it can take several days of normal driving.

350

If the indicator comes on repeatedly, even though it may turn off as you continue driving, have your vehicle checked by the dealer as soon as possible.

If you keep driving with the malf unction indicator lamp on, you can damage your vehicle’s emissions controls and engine. Those repairs may not be covered by your vehicle’s warranties.

If your vehicle has an automatic transmission, the malfunction indicator lamp may also come on with the ‘‘D’’ indicator.

Readiness Codes Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure

these codes are set. If they are not set, the test cannot be completed.

If the battery in your vehicle has been disconnected or gone dead, these codes may be erased. It can take several days of driving under various conditions to set the codes again.

To check if they are set, turn the ignition switch to the ON (II) position, without starting the engine. The malfunction indicator lamp will come on for 20 seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If possible, do not take your vehicle for an emissions test until the readiness codes are set. Emissions Testing Refer to more information (see page

for 376

).

10/06/24 17:07:57 31SVA650_356

U.S.

Canada

The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.

If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level the next time you stop at a service station (see page

310

).

If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.

Brake System Indicator

If the ABS indicator and the VSA system indicator (if equipped) come on with the brake system indicator, have your vehicle inspected by your dealer immediately.

However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down, and you will have to press harder on the pedal.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing 358

Emergency ).

on page

If you must drive the vehicle a short distance in this condition, drive slowly and carefully.

351

10/06/24 17:08:04 31SVA650_357

Fuses

INTERIOR

UNDER-HOOD

TAB

FUSE LABEL

The vehicle’s fuses are contained in two fuse boxes.

The interior fuse box is on the driver’s lower left side.

The under-hood fuse box is in the engine compartment on the driver’s side, next to the brake fluid reservoir. To open it, push the tabs as shown.

352

356

and

Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages , or the diagram on the fuse box lid, which fuse or fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works.

357

10/06/24 17:08:11 31SVA650_358

FUSE

BLOWN

FUSE

BLOWN

Fuses

1.

Turn the ignition switch to the LOCK (0) position. Make sure the headlights and all other accessories are off.

2.

Remove the cover from the fuse box.

3.

Check each of the large fuses in the under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screw- driver.

4.

Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each one with the fuse puller provided on the back of the under-hood fuse box cover.

FUSE PULLER

CONTINUED

353

10/06/24 17:08:17 31SVA650_359

Fuses

BLOWN

5.

Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower.

354

If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate that anything is wrong. Replace the fuse with one of the correct rating as soon as you can.

Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating.

6.

If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem in your vehicle. Leave the blown fuse in that circuit and have your vehicle checked by a qualified technician.

10/06/24 17:08:21 31SVA650_360

SPARE FUSES

FUSE PULLER

Your vehicle has spare fuses on the back of the under-hood fuse box cover.

AllmodelsexceptDXandCanadian DX-G If the driver’s power window fuse is removed, the AUTO function of the driver’s window will be disabled. You should reset the AUTO feature (see page

105

).

Fuses

355

10/06/24 17:08:27 31SVA650_361

Fuse Locations

UNDER-HOOD FUSE BOX

No.

Amps. 100 A (70 A) 60 A 50 A 30 A 30 A 40 A 50 A 40 A

＊

Circuits Protected

＊

Main Fuse EPS Option Main Ignition Switch Main ABS/VSA Motor ABS/VSA F/S

Headlight Main Power Window Main

356

No. Amps.

− 20 A 30 A 20 A 40 A 40 A 10 A 15 A 15 A − − 7.5 A −

(15 A) 15 A 15 A 7.5 A 15 A 7.5 A 10 A

10
11
12
13
14
15
16
17
18
19
20
21
22
23

Circuits Protected

Not Used Sub Fan Motor Main Fan Motor (A/T) Main Fan Motor (M/T) Rear Defroster Blower Hazard FI Sub Stop, Horn Not Used Not Used Oil Level Sensor Not Used Audio Amp Ignition Coil FI Main MG Clutch DBW Interior Light Back Up

＊

＊ ＊

1 : 2 :

EX-L and Si models If equipped

10/06/24 17:08:36 31SVA650_362

INTERIOR FUSE BOX

No.

Amps. 7.5 A 15 A 10 A 7.5 A (15 A) (20 A) (7.5 A)

−

Circuits Protected

Power Window Fuel Pump IG1 ACG ABS/VSA Heated Seats Front Fog Lights TPMS Not Used

＊

＊

＊

Fuse Locations

No. 17
18
19
20
21
22
23
24
25
26
27
28
29
30

31
32
33
34
35
36
37
38

Amps. 10 A 20 A 15 A − 20 A − −

(20 A) 20 A 20 A (20 A) (15 A) 15 A 20 A

− − − − 7.5 A 10 A 7.5 A 30 A

＊

If equipped

No. Amps. 7.5 A

10
11
12
13
14
15
16

7.5 A 10 A 10 A 10 A 7.5 A 7.5 A 10 A

Circuits Protected

ODS (Occupant Detection System) Meter SRS Right Headlight High Beam Left Headlight High Beam Small Lights (Interior) Small Lights (Exterior) Right Headlight Low Beam

＊

Circuits Protected Left Headlight Low Beam Headlight High Beam Main Small Lights Main Not Used Headlight Low Beam Main Not Used Not Used Moonroof Door Lock Driver’s Power Window HAC Option Rear Accessory Socket Accessory Front Passenger’s Power Window Not Used Not Used Not Used Not Used Accessory, Radio IG2 HAC Daytime Running Lights Front Wiper

＊

357

10/06/24 17:08:48 31SVA650_363

Emergency Towing

If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous.

There are two ways to tow your vehicle:

−

Flat-bedEquipment loads your vehicle on the back of a truck. transport your vehicle.

This is the best way to

The operator

−

The tow

Wheel-liftEquipment truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. way to tow your vehicle.

This is an acceptable

358

If, due to damage, your vehicle must be towed with the front wheels on the ground, do this:

Manualtransmission:

Shift the transmission to neutral. Leave the ignition switch in the ACCESSORY (I) position so the steering wheel does not lock. Release the parking brake.

Automatictransmission:

Start the engine. Shift to the D position and hold for 5 seconds, then to N. Turn off the engine. Leave the ignition switch in the ACCESSORY (I) position so the steering wheel does not lock. Release the parking brake.

Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shif t the transmission or start the engine (automatic transmission), your vehicle must be transported with the f ront wheels of f the ground.

With the front wheels on the ground, do not tow the vehicle more than 50
miles (80 km), and keep the speed below 35 mph (55 km/h).

Do not tie down the vehicle at an angle that would allow the towing cables to contact the vehicle’s front bumper. To avoid possible damage, protect the front bumper with tape.

If your vehicle is equipped with a front spoiler, remove it before towing so it is not damaged.

10/06/24 17:08:51 31SVA650_364

Emergency Towing

Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight.

The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing.

359

10/06/24 17:08:53 31SVA650_365

360

10/06/24 17:08:58 31SVA650_366

The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems.

Identification Numbers Specifications DOT Tire Quality Grading

................ ................................

. 362
. 364

(U.S. Vehicles)

......................

. 367

Uniform Tire Quality

Grading Treadwear Traction Temperature

.................................. ................................. ...................................... ............................. Tire Labeling ................................. Tire Pressure Monitoring System

. 367
. 367
. 367
. 368
. 369

(TPMS)

−

Explanation

Required Federal ............................

. 371

Technical Information

Emissions Controls ....................... The Clean Air Act ..................... Crankcase Emissions Control .................................... Evaporative Emissions Control ....................................

System

System

Onboard Refueling Vapor

. 373
. 373

. 373

. 373

Recovery

. 373
Exhaust Emissions Controls . 374
. 374

................................ ... ....................

PGM-FI System Ignition Timing Control

System

................................ Exhaust Gas Recirculation ...................

(EGR) System

Three Way Catalytic

. 374

. 374

Converter

Replacement Parts

. 374
........................... .................... . 374
.. Three Way Catalytic Converter . 375
........................ . 376
Emissions Testing

361

10/06/24 17:09:02 31SVA650_367

Identification Numbers

Your vehicle has several identifying numbers located in various places.

The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also