2008 Honda Accord Coupe Owners Manual

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. For more information, see page

280

58

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１５：２０　３１ＴＥ０６００　００６４　

Low Tire Pressure Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page information, see page

). For more 284

349

371

Instrument Panel Indicators

Fuel Economy Indicator

V6modelswithautomatictransmission While the engine is operating in its most economical range, this indicator may come on and stay on.

Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

59

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１８：３８：０７　３１ＴＥ０６００　００６５　

Instrument Panel Indicators

Daytime Running Lights Indicator

If this indicator comes on when you turn the ignition switch to the ON (II) position and release the parking brake, it means there is a problem with the DRL. There may also be a problem with the high beam headlights. Have your vehicle checked by your dealer.

High Beam Indicator

This indicator comes on with the high beam headlights. For more information, see page

70

This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page

72

).

60

Lights On Indicator

Low Fuel Indicator

This indicator comes on as a reminder that you must refuel soon. When the indicator comes on, there is about 2.8 U.S. gal (10.5 ) of fuel remaining in the tank.

When the needle reaches E, there is a very small amount of fuel in the tank.

or

This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the

ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the light switch, this indicator will stay on. A reminder chime will also sound when you open the driver’s door.

EX-LandallV6models This indicator will also come on when the light switch is in AUTO and the lights turn on automatically.

Washer Level Indicator

Canadianmodelsonly This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page

312

).

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１５：４０　３１ＴＥ０６００　００６６　

Maintenance Minder Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page 297
maintenance minder.

for more information on the

This indicator goes off when your dealer resets it after completing the required maintenance service.

Instrument Panel Indicators

Door and Trunk Open Indicator

Security System Indicator

DRIVER’S DOOR OPEN INDICATOR

SECURITY SYSTEM INDICATOR

TRUNK OPEN INDICATOR

The appropriate indicator comes on if the trunk or either door is not closed tightly.

All the indicators come on for a few seconds when you turn the ignition switch to the ON (II) position.

This indicator comes on when the security system is set. For more information, see page

204

61

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１５：５４　３１ＴＥ０６００　００６７　

Instrument Panel Indicators

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page for more information on the 282
VSA system.

62

VSA Activation Indicator

Cruise Main Indicator

This indicator has three functions:

1.

2.

3.

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

282

).

It comes on along with the VSA system indicator if there is a problem with the VSA system.

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page

282

This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page

210

).

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page 210
cruise control.

for information on operating the

Fog Light Indicator

Ifequipped This indicator comes on when you turn on the fog lights. For more information, see page

73

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：００　３１ＴＥ０６００　００６８　

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

OUTSIDE TEMPERATURE INDICATOR

＊

TRIP METER

SELECT/RESET KNOB

ODOMETER/CHECK FUEL CAP MESSAGE

INFORMATION DISPLAY

U.S. A/T model is shown.

＊

If equipped

Gauges

63

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：０７　３１ＴＥ０６００　００６９　

Gauges

INFORMATION DISPLAY

ODOMETER

TRIP METER A

ENGINE OIL LIFE

OUTSIDE TEMPERATURE INDICATOR

U.S. model with outside temperature indicator is shown.

TRIP METER B

Information Display The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), and maintenance item code(s).

To switch the display, press and release the select/reset knob repeatedly. When you turn the ignition switch to the ON (II) position, what you last selected is displayed.

64

Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：１６　３１ＴＥ０６００　００７０　

Gauges

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system.

359

Trip Meter The trip meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the select/reset knob repeatedly.

Each trip meter works independently, so you can keep track of two different distances.

When you turn the ignition switch to the ON (II) position, what you last selected is displayed.

To reset a trip meter, display it and then press and hold the select/reset knob until the number resets to ‘‘0.0’’.

65

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：２４　３１ＴＥ０６００　００７１　

Gauges

Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models). To see the outside temperature, press and release the select/reset knob until the temperature is displayed.

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).

66

The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes.

When the temperature reaches the desired value, release the select/ reset knob. You should see the new outside temperature displayed.

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

NOTE: The temperature must be stabilized before doing this procedure.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

Select the outside temperature display, then press and hold the select/reset knob for 10 seconds. The following sequence will appear for 1 second each: 0, 1, 2, 3, 4, 5, 5, − 1, 0 (U.S.) or 0, 1, 2, − − − − 3,

4, 2, − − −

1, 0 (Canada).

3,

3,

2,

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：２９　３１ＴＥ０６００　００７２　

Check Fuel Cap Message If your fuel fill cap is loose or missing, a ‘‘CHECK FUEL CAP’’ message appears on the information display after you start the engine. For more information, see page

251

Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

297

for

Gauges

67

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：３７　３１ＴＥ０６００　００７３　

Controls Near the Steering Wheel

HEADLIGHTS/ TURN SIGNALS/ FOG LIGHTS (P.70, 73)

＊

REMOTE AUDIO CONTROLS (P.198)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.283)

STEERING WHEEL ADJUSTMENTS (P.76)

＊

NAVIGATION SYSTEM VOICE CONTROL BUTTONS BLUETOOTH HANDSFREELINK VOICE CONTROL BUTTONS ＊ (P.218)

INSTRUMENT PANEL BRIGHTNESS (P.73)

WINDSHIELD WIPERS/ WASHERS

(P.69)

PASSENGER AIRBAG OFF INDICATOR (P.30)

HAZARD WARNING BUTTON (P.74)

INTERFACE DIAL ＊ (P.161)

HORN ＊

CRUISE CONTROL BUTTONS (P.210)

REAR WINDOW DEFOGGER (P.75)

SEAT HEATER SWITCHES (P.101)

＊

To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual.

1 : 2 : 3 :

＊ ＊ ＊ 68

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：４７　３１ＴＥ０６００　００７４　

Windshield Wipers and Washers

Windshield Wipers

ADJUSTMENT RING

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low speed HI High speed Windshield washers

Intermittent

− − −

Push the right lever up or down to select a position.

MIST

−

The wipers run at high

speed until you release the lever.

OFF

−

The wipers are not activated.

INT

−

The length of the wiper

interval is varied automatically according to the vehicle’s speed.

Vary the delay by turning the adjustment ring. If you turn it to the shortest delay position), the wipers change to low speed operation when the vehicle speed exceeds 12
mph (20 km/h).

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

−

Windshield Washers

Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.

69

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１６：５５　３１ＴＥ０６００　００７５　

Turn Signals and Headlights

−

Turn Signal Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.

−

Turning the switch to

’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.

Turning the switch to the ‘‘ position turns on the headlights.

’’

If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.

V6 model is shown.

1. 2. 3. 4. 5. 6. 7. 8. 9.

＊

Turn signal Off Parking and indicator lights AUTO Headlights on High beams Flash high beams Fog lights off Fog lights on

＊

＊

＊

If equipped

70

’’ or ‘‘

When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder. This indicator stays on if you leave the light switch on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

−

High Beams Push the left lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

60

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：０３　３１ＴＥ０６００　００７６　

Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities.

Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.

Headlights

LIGHT SENSOR

The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.

− The automatic lighting

EX-LandallV6models AUTO feature turns on the headlights and all other exterior lights, when it senses low ambient light.

To turn on automatic lighting, turn the light switch to AUTO at any time. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light.

The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver’s door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the

position.

71

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：０９　３１ＴＥ０６００　００７７　

Headlights

Automatic Lighting Off Feature This feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15
seconds after you remove the key and close the driver’s door.

’’ or ‘‘

The automatic lighting off feature activates if you leave the headlight switch in the ‘‘ position or if the lights are turned on by setting the switch in the ‘‘AUTO’’ position (if equipped), and you remove the key, then open and close the driver’s door.

’’

If you turn the ignition switch to the LOCK (0) position with the headlight switch on, but do not open the door and get out, the lights turn off after 10 minutes (3 minutes, if the switch is in the ‘‘AUTO’’ position).

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights will go off. With the driver’s door open, you will hear a lights on reminder chime.

position, the high beam

Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the switch.

72

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：１７　３１ＴＥ０６００　００７８　

Fog Lights

AllV6models Turn the fog lights on and off by turning the switch next to the headlight switch.

Fog Lights, Instrument Panel Brightness

Instrument Panel Brightness

You can use the fog lights only when the headlights are on low beam. With the light switch in the AUTO position (if equipped), you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off, or the daytime running lights are on.

SELECT/RESET KNOB

The select/reset knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness with the ignition switch in the ON (II) position and the parking lights on.

CONTINUED

73

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：２５　３１ＴＥ０６００　００７９　

Instrument Panel Brightness, Hazard Warning Button

The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal brightness when you turn the ignition switch to the ON (II) position.

If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.

If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.

Hazard Warning Button

U.S. model is shown.

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

BRIGHTNESS LEVEL

The level of brightness is shown on the information display while you adjust it. It goes out about 5 seconds after you finish adjusting.

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to

or

. Turning the select/

reset knob to the right until you hear a beep will cancel the reduced brightness.

74

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：３３　３１ＴＥ０６００　００８０　

U.S. LX, LX-S

Manual A/C type

Except U.S. LX, LX-S

Auto A/C type

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.

Onvehicleswithautomaticair conditioningsystem The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature (over 32°F, 0°C).

Make sure the rear window is clear and you have good visibility before starting to drive.

Rear Window Defogger

Vehicles with navigation system

The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.

ExceptU.S.LXandLX-S Pushing this button also turns the mirror heaters on or off. For more information, see page

103

75

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：３９　３１ＴＥ０６００　００８１　

3.

Push the lever up to lock the steering wheel in position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.

2.

Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

Steering Wheel Adjustments

Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

1.

Push the lever under the steering column all the way down.

76

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：４７　３１ＴＥ０６００　００８２　

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (Light Grey)

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

Keys and Locks

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the trunk release handle, and glove box locked when you leave your vehicle and the valet key at a parking facility.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The valet key does not contain a battery. Do not try to take it apart.

77

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１７：５５　３１ＴＥ０６００　００８３　

Immobilizer System

The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.

78

If the system repeatedly does not recognize the coding of your key, contact your dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.

If you lose your key and you cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１８：０３　３１ＴＥ０６００　００８４　

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), START (III)

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in Park.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

Ignition Switch

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

If your vehicle has an automatic transmission, the shift lever must be in Park before you can remove the key from the ignition switch.

Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.

Remove the key from the ignition switch only when parked.

79

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１７：５４：５０　３１ＴＥ０６００　００８５　

Door Locks

POWER DOOR LOCK MASTER SWITCH

Lock

Unlock

To lock both doors, push the front of the master door lock switch on either door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door.

Pushing the rear of either master door lock switch will unlock both doors. Pushing forward the lock tab on the driver’s door only unlocks that door.

80

LOCK TAB

Lock

Unlock

Both doors can be locked from the outside by using the key in the driver’s door. To unlock only the driver’s door, insert the key, turn it clockwise, and release it. The passenger’s door unlocks when you turn the key a second time within a few seconds.

RED INDICATOR

The lock tab on the passenger’s door locks and unlocks that door.

When the door is unlocked, you can see the red indicator on the lock tab above the inner door handle.

You can open or close the windows and the moonroof (if equipped) by using the key in the driver’s door (see page

106

).

To lock the passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door. To lock the driver’s door, remove the key from the ignition switch, pull the lock tab rearward or push the front of the master switch, then close the door.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１８：１９　３１ＴＥ０６００　００８６　

Door Locks

LockoutPrevention If you forget and leave the key in the ignition switch, lockout prevention will not allow you to lock the driver’s door. With either door open and the key in the ignition switch, locking with master door lock switch is disabled. If the driver’s door is closed, the lock tab on the driver’s door is not disabled. Pulling the driver’s lock tab rearward will lock both doors. If you try to lock an open driver’s door by pulling the lock tab rearward, the driver’s door lock tab pops out and unlocks the driver’s door.

Auto Door Locking/Unlocking Your vehicle has customizable settings for the doors to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages.

When you customize the setting, make sure your vehicle is parked safely, the engine is off, and apply the parking brake. Make all settings before you start driving.

Auto Door Locking The auto door locking feature has three possible settings:

The auto door locking is deactivated all the time.

The doors lock whenever you move the shift lever out of the Park (P) position (A/T vehicles).

The doors lock when the vehicle speed reaches 9 mph (15 km/h). This is the default setting.

CONTINUED

81

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１８：２９　３１ＴＥ０６００　００８７　

Door Locks

ToturnofftheAutoDoorLock modes:

1.

Make sure the shift lever is in the Park (P) position (A/T vehicles).

2.

Turn the ignition switch to the ON (II) position, and open the driver’s door.

82

3.

Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).

ToprogramtheParkLockmode: Locksbothdoorswhentheshiftleveris movedoutofthePark(P)position(A/T vehiclesonly).

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１８：３８　３１ＴＥ０６００　００８８　

ToprogramtheDriveLockmode: Locksbothdoorswhenthevehicle’s speedreachesabout9mph(15km/h).

3.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a click. Keep holding the switch until you hear another click (after about 5
seconds).

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position (A/T vehicles).

2.

3.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

OnA/Tvehicles, brake pedal, and move the shift lever out of the Park (P) position.

push and hold the

Door Locks

4.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a click. Keep holding the switch until you hear another click (after about 5
seconds).

5.

Release the switch, and within 5
seconds, turn the ignition switch to the ACCESSORY (I) position. move the shift OnA/Tvehicles, lever to the Park (P) position.

6.

Turn the ignition switch to the LOCK (0) position.

83

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１８：４９　３１ＴＥ０６００　００８９　

Door Locks

Auto Door Unlocking The auto door unlocking feature has five possible settings:

The auto door unlocking is deactivated all the time.

the driver’s door OnA/Tvehicles, unlocks when you move the shift lever to the Park (P) position. This is the default setting.

Both doors unlock when you move the shift lever to the Park (P) position (A/T vehicles).

The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position. This is the default setting on M/T vehicles.

Both doors unlock whenever you turn the ignition switch to the ACCESSORY (I) position.

84

ToturnofftheAutoDoorUnlock modes:

3.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position (A/T vehicles).

2.

Turn the ignition switch to the ON (II) position, and open the driver’s door.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：０１　３１ＴＥ０６００　００９０　

ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororbothdoors whentheshiftleverismovedintothe Park(P)position(A/Tvehiclesonly).

3.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:

Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature.

Or, until you hear two more clicks (after about 10 seconds) to activate feature

bothdoorsunlock

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

Door Locks

ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororbothdoors whentheignitionswitchismovedoutof theON(II)position.

1.

Make sure the shift lever is in the Park (P) position (A/T vehicles).

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

CONTINUED

85

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：０８　３１ＴＥ０６００　００９１　

Door Locks

3.

4.

OnA/Tvehicles, brake pedal, then move the shift lever out of the Park (P) position.

push and hold the

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:

5.

Release the switch, and within 5
seconds, turn the ignition switch to the ACCESSORY (I) position. move the shift OnA/Tvehicles, lever to the Park (P) position.

6.

Turn the ignition switch to the LOCK (0) position.

Even though your vehicle’s battery is removed or goes dead, the system keeps the auto door lock/unlock setting which you selected.

Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature.

Or, until you hear two more clicks (after about 10 seconds) to activate feature

bothdoorsunlock

86

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：１６　３１ＴＥ０６００　００９２　

Remote Transmitter

LED

UNLOCK BUTTON

PANIC BUTTON

LOCK BUTTON

TRUNK RELEASE BUTTON

−

Press this button once to

LOCK lock both doors. Some exterior lights will flash once. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked and that the security system (if equipped) has set. You cannot lock the doors if either door is not fully closed or the key is in the ignition switch.

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the passenger’s door. Some exterior lights will flash twice each time you push the button.

The ceiling light and the door activated spotlights (if equipped) come on when you press the UNLOCK button if the lights are in the door activated position. If you do not open either door within 30
seconds, the light(s) will fade out. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the light(s) will go off immediately.

If you do not open either door within 30 seconds, the doors automatically relock and the security system sets.

You can also open both power windows and the moonroof (if equipped) from outside the vehicle with the remote transmitter (see page

106

).

−

Press and hold this

PANIC button for about 2 seconds to attract attention: the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.

−

Press and hold this

TRUNK button for about 1 second to open the trunk. You cannot open the trunk if the key is in the ignition switch.

CONTINUED

87

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：２６　３１ＴＥ０６００　００９３　

Remote Transmitter

RemoteTransmitterCare

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

ReplacingtheTransmitterBattery If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible.

Battery type: CR1616

To replace the battery:

If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

NOTE: Be careful when removing this screw as the head of the screw can strip out.

SCREW

2.

Separate the transmitter by prying its middle seam with your fingernail.

88

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：３４　３１ＴＥ０６００　００９４　

4.

Remove the old battery, and insert a new battery into the back of the cover with the

side facing down.

＋

An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

5.

Install the parts in reverse order.

BATTERY

TAB

3.

Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

89

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：４２　３１ＴＥ０６００　００９５　

Trunk

Pull

To close the trunk, press down on the trunk lid.

Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from Carbon getting into the interior. See Monoxide Hazard 51
on page

TRUNK RELEASE LEVER

You can open the trunk in two ways:

Pull up on the trunk release lever to the left of the driver’s seat.

Press and hold the trunk release button on the remote transmitter.

90

MASTER KEY

To protect items in the trunk when you need to give the key to someone else:

1.

Lock the trunk release lever with the master key.

2.

Give the person the valet key.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：１９：４９　３１ＴＥ０６００　００９６　

Even if the trunk release lever is locked with the master key, you can open the trunk with the remote transmitter.

Emergency Trunk Opener

Parents should decide if their children should be shown how to use this feature.

Trunk

As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside.

To open the trunk, push the release lever in the direction indicated by the arrow.

For more information about child safety, see page

37

91

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：２０：００　３１ＴＥ０６００　００９７　

Seats

Driver’s Seat Power Adjustments ExceptLXandEX Seepages 11 13
forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

−

The controls for the power adjustable driver’s seat are on the outside edge of the seat bottom. You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving.

The front passenger’s seat adjusts manually.

92

Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.

Adjusts the seat-back angle forward or backward.

Increases or decreases the lumbar support.

Moves the seat forward