Download PDF Manual

(cid:129) Prevent ignition key removal unless the shift


lever is in PARK (P) with the shift lever button fully released, and


(cid:129) Prevent movement of the shift lever out of PARK (P),


unless the ignition is in ON/RUN or ACC/ ACCESSORY and the regular brake pedal is applied.


2-34


Information Provided by: Parking Over Things That Burn


Engine Exhaust


{CAUTION:


{CAUTION:


Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn.


Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if:


(cid:129) The exhaust system sounds strange or


different.


(cid:129) Your vehicle gets rusty underneath. (cid:129) Your vehicle was damaged in a collision. (cid:129) Your vehicle was damaged when driving over high points on the road or over road debris.


(cid:129) Repairs were not done correctly. (cid:129) Your vehicle or the exhaust system has


been modified improperly.


If you ever suspect exhaust is coming into your vehicle:


(cid:129) Drive it only with all the windows down to


blow out any CO; and


(cid:129) Have your vehicle fixed immediately.


2-35


Information Provided by: Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know.


{CAUTION:


{CAUTION:


Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-35. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-28.


It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P).


Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) on page 2-33. If you are pulling a trailer, see Towing a Trailer on page 4-41.


2-36


Information Provided by: Mirrors


Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle may have this feature. When on, an automatic dimming inside rearview mirror automatically dims to the proper level to minimize glare from lights behind you after dark. The mirror also includes a dual display in the upper right corner of the mirror face. The compass reading and the outside temperature will both appear in the display at the same time. P(On/Off): This is the on/off button. Temperature and Compass Display Press the on/off button, located to the far left, briefly to turn the compass/temperature display on or off. If the display reads CAL, you will need to calibrate the compass. For more information on calibration see “Compass Calibration” following.


To adjust between Fahrenheit and Celsius: 1. Press and hold the on/off button for approximately four seconds until either a flashing F or C appears.


2. Press the button again to change the display to the desired unit of measurement. After approximately four seconds of inactivity, the new unit will be locked in and the compass/temperature display will return. If an abnormal temperature reading is displayed for an extended period of time, please see your dealer. Under certain circumstances, a delay in updating the temperature is normal. Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit. If it’s not, press and hold the on/off button for approximately six seconds until the green light comes on, indicating that the mirror is in automatic dimming mode.


2. Turn off the automatic dimming mirror function by


pressing and holding the on/off button for approximately six seconds, until the green indicator light turns off.


2-37


Information Provided by: Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance do the following: 1. Find your current location and variance zone


number on the following zone map.


2-38


2. Press and hold the on/off button until a Z and a


zone number appears in the display. The compass is now in zone mode.


3. Keep pressing the on/off button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return.


4. Calibrate the compass as described below.


Information Provided by: Compass Calibration The compass may need calibration if one of the following occurs: (cid:129) After approximately five seconds, the display does


not show a compass heading (N for North, for example), there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly.


In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push the on/off button for approximately 12 seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.


Outside Power Mirrors


If your vehicle is equipped with outside power mirrors, the controls are located on the driver’s door armrest.


(cid:129) Press (A) to select the driver’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (A) again to deselect the mirror.


(cid:129) Press (B) to select the passenger’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (B) again to deselect the mirror.


This mirror has the following features.


2-39


Information Provided by:(cid:129) Manual Folding The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure to return both mirrors to their original unfolded position before driving. Heated Mirrors The button to turn the heated mirrors on or off is located on the climate control panel. Press this button to warm the driver’s and passenger’s outside rearview mirrors to help clear them of ice, snow, and condensation. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-26 for more information.


Convex Mirror The passenger’s side mirror may have convex glass. A convex mirror’s surface is curved so more can be seen from the driver’s seat.


{CAUTION:


A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.


2-40


Information Provided by: Outside Power Foldaway Mirrors


If your vehicle is equipped with outside power foldaway mirrors, the controls are located on the driver’s door armrest.


(cid:129) Press (A) to select the driver’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (A) again to deselect the mirror.


(cid:129) Press (B) to select the passenger’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (B) again to deselect the mirror.


(cid:129) Press (C) to fold the mirrors out to the driving


(cid:129) Press (D) to fold the mirrors in to the folded


position.


position.


If the mirrors are accidentally folded/unfolded manually, they may shake or flutter at normal driving speeds and may not stay in the unfolded position. If this happens, you will need to reset the mirrors. See “Resetting the Power Foldaway Mirrors” next. Resetting the Power Foldaway Mirrors You will need to reset the power foldaway mirrors if the following occurs:


The mirrors are accidentally obstructed while folding. They are accidentally manually folded/unfolded. The mirrors will not stay in the unfolded position. The mirrors shake and flutter at normal driving speeds.


To reset the power foldaway mirrors, fold and unfold them one time using the mirror controls. This will reset them to their normal position. This mirror has the following features. Automatic Dimming The driver’s outside mirror will adjust for the glare of the headlamps behind you. See Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display on page 2-37.


2-41


Information Provided by:(cid:129) (cid:129) (cid:129) (cid:129) Convex Mirror


{CAUTION:


A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.


The passenger’s side mirror may have convex glass. A convex mirror’s surface is curved so more can be seen from the driver’s seat. Your vehicle may also have a turn signal indicator on the mirror. An arrow on the mirror will flash in the direction of the turn or lane change.


Park Tilt Mirrors If your vehicle has the memory package, the outside mirrors are able to perform the park tilt function. This feature may be useful in allowing the driver to view the curb when parallel parking. This feature will cause the passenger’s and/or driver’s mirror to tilt to a preselected position when the vehicle is in REVERSE (R). The passenger’s and/or driver’s mirror will return to its original position when the vehicle is shifted out of REVERSE (R), or the ignition is turned off or to OFF/LOCK. This feature can be turned on or off through the Driver Information Center (DIC). See DIC Vehicle Customization (With DIC Buttons) on page 3-68. Heated Mirrors The button to turn the heated mirrors on or off is located on the climate control panel. Press this button to warm the driver’s and passenger’s outside rearview mirrors to help clear them of ice, snow, and condensation. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-26 for more information.


2-42


Information Provided by: Object Detection Systems Ultrasonic Rear Parking Assist (URPA) If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system, it helps you park easier and avoid other vehicles while in REVERSE (R). It operates at speeds less than 5 mph (8 km/h). It can determine how close objects are to the rear bumper, up to 8 feet (2.5 m) behind your vehicle. The distance sensors are located on the rear bumper.


{CAUTION:


The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect:


(cid:129) objects that are below the bumper,


underneath the vehicle, or if they are too close or far from the vehicle


(cid:129) children, pedestrians, bicyclists, or pets.


CAUTION:


(Continued)


CAUTION:


(Continued)


If you do not use proper care before and while backing; vehicle damage, injury, or death could occur. Even with URPA, always check behind your vehicle before backing up. While backing, be sure to look for objects and check your vehicle’s mirrors.


On some vehicles this display is located near the passenger side rear window and can be seen by looking over your right shoulder.


If your vehicle has the display, there are three color-coded lights to provide distance and system information. If your vehicle does not have the display and it has URPA, you will hear the beeps as described in the following information.


2-43


Information Provided by: How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R). The rear display will then briefly illuminate to let you know the system is working. URPA operates only at speeds less than 5 mph (8 km/h). If you are above this speed, the red light on the rear display will flash. To be detected, objects must be at least 10 inches (25.4 cm) off the ground and below tailgate level. Objects must also be within 8 feet (2.5 m) from your rear bumper. This distance may be less during warmer or humid weather. A single beep will sound the first time an object is detected between 20 inches (0.5 m) and 8 feet (2.5 m) away. Beeping will occur for three seconds when you are closer than 1 foot (0.3 m) from the object.


The following describes what will occur with the URPA display as you get closer to a detected object:


Description amber light


amber/amber lights


amber/amber/red lights amber/amber/red lights flashing and beep for


three seconds


English


8 ft 40 in 23 in


1 ft


Metric 2.5 m 1.0 m 0.6 m


0.3 m


The system can be disabled by pressing the rear park aid disable button located next to the radio. The indicator light will come on to indicate that URPA is off.


If you use URPA while the tailgate is


Notice: lowered, it may not detect an object behind your vehicle, and you might back into the object and damage your vehicle. Always verify the tailgate is closed when using URPA or turn off URPA when driving with the tailgate lowered.


2-44


Information Provided by: When the System Does Not Seem to Work Properly


The driver disables the system. The parking brake pedal is depressed. The ultrasonic sensors are not clean. Keep your vehicle’s rear bumper free of mud, dirt, snow, ice and slush. For cleaning instructions, see Washing Your Vehicle on page 5-102.


(cid:129) A trailer was attached to your vehicle, or a bicycle


or an object was hanging out of your tailgate during your last drive cycle, the red light may illuminate in the rear display. Once the attached object is removed, URPA will return to normal operation.


(cid:129) A tow bar is attached to your vehicle.


The vehicle’s bumper is damaged. Take the vehicle to your dealer/retailer to repair the system.


(cid:129) Other conditions may affect system performance,


such as vibrations from a jackhammer or the compression of air brakes on a very large truck. If the system is still disabled, after driving forward at least 15 mph (25 km/h), take your vehicle to your dealer/retailer.


OnStar® System


OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar button and they can contact Roadside Service for you.


2-45


Information Provided by:(cid:129) (cid:129) (cid:129) (cid:129) OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. Not all OnStar features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in your glove box or visit onstar.com. OnStar Services For new vehicles with OnStar, the Safe & Sound Plan, or the Directions & Connections Plan is included for one year from the date of purchase. You can extend this plan beyond the first year, or upgrade to the Directions & Connections Plan. For more information, press the OnStar button to speak with an advisor. Some OnStar services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar.


2-46


Available Services with Safe & Sound Plan (cid:129) Automatic Notification of Airbag Deployment (cid:129) Advanced Automatic Crash Notification (AACN) (If


equipped) Link to Emergency Services


(cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) AccidentAssist (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar Vehicle Diagnostics (cid:129) GM Goodwrench® On Demand Diagnostics (cid:129) OnStar Hands-Free Calling with 30 complimentary


minutes


(cid:129) OnStar Virtual Advisor (U.S. Only) Available Services included with Directions & Connections Plan (cid:129) All Safe and Sound Plan Services (cid:129) Driving Directions - Advisor delivered or OnStar


Turn-by-Turn Navigation (If equipped)


(cid:129) RideAssist


Information and Convenience Services


Information Provided by:(cid:129) (cid:129) OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-120 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” to activate the OnStar Hands-Free Calling. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information.


OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To find out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information (Only available in the continental U.S.).


2-47


Information Provided by: How OnStar Service Works Your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times.


Location information about your vehicle is only available if the GPS satellite signals are unobstructed and available. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the OnStar button to confirm that your OnStar equipment is active.


2-48


Information Provided by: Universal Home Remote System


Universal Home Remote System Operation (With Three Round LED)


Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received,


including interference that may cause undesired operation.


This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received,


including interference that may cause undesired operation of the device.


Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.


Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter.


2-49


Information Provided by: Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for Fixed Code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, it is advised to park outside of the garage. Be sure that people and objects are clear of the garage door or security device you are programming. Programming Universal Home Remote — Rolling Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units.


Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. To program up to three devices:


1. From inside the vehicle, press the two outside


buttons at the same time for one to two seconds, and immediately release them.


2-50


Information Provided by: 3. Immediately return to your vehicle. Press and hold the Universal Home Remote button that you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from five to 20 seconds.


4. Immediately, within one second, release the button


when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the same button again. The


garage door should move, confirming that programming is successful and complete.


2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After you press this button, you will have 30 seconds to complete the following steps.


To program another Rolling Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1 through 5, choosing a different function button in Step 3 than what you used for the garage door opener. If these instructions do not work, you probably have a Fixed Code garage door opener. Follow the Programming instructions that follow for a Fixed Code garage door opener.


2-51


Information Provided by: To program up to three devices:


Programming Universal Home Remote — Fixed Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure.


1. To verify if you have a Fixed Code garage door opener, remove the battery cover on your hand held transmitter supplied by the manufacturer of your garage door opener motor. If you see a row of dip switches similar to the graphic above, you have a Fixed Code garage door opener. If you do not see a row of dip switches, return to the previous section for Programming Universal Home Remote – Rolling Code. Your hand held transmitter may have between eight to 12 dip switches depending on the brand of transmitter.


2-52


Information Provided by: Your garage door opener receiver (motor head unit) may also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program your Universal Home Remote. The motor head dip switch settings can also be used when you do not have the original hand held transmitter.


Example of Eight Dip Switches with Two Positions


Example of Eight Dip Switches with Three Positions


Your panel of switches may not appear exactly as they do in the examples, but they should be similar. The switch positions on your hand-held transmitter may be labeled as follows: (cid:129) A switch in the up position may be labeled as


“Up,” “+,” or “On.”


(cid:129) A switch in the down position may be labeled as


“Down,” “−,” or “Off.”


(cid:129) A switch in the middle position may be labeled


as “Middle,” “0,” or “Neutral.”


2-53


Information Provided by: 2. Write down the eight to 12 switch settings from left


to right as follows: (cid:129) When a switch is in the up position, write “Left.” (cid:129) When a switch is in the down position, write


“Right.” If a switch is set between the up and down position, write “Middle.” The switch settings that you wrote down in Step 2 will now become the button strokes you enter into the Universal Home Remote in Step 4. Be sure to enter the switch settings that you wrote down in Step 2, in order from left to right, into the Universal Home Remote, when completing Step 4.


3. From inside your vehicle, first firmly press all three buttons at the same time for about three seconds. Release the buttons to put the Universal Home Remote into programming mode.


4. The indicator lights will blink slowly. Enter each


switch setting from Step 2 into your vehicle’s Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows:


If you wrote “Left,” press the left button in the vehicle. If you wrote “Right,” press the right button in the vehicle. If you wrote “Middle,” press the middle button in the vehicle.


2-54


Information Provided by:(cid:129) (cid:129) (cid:129) (cid:129) 5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on.


6. Press and hold the button you would like to use to


control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the button from five to 55 seconds.


7. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete.


8. Press and release the same button again. The


garage door should move, confirming that programming is successful and complete.


To program another Fixed Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1-8, choosing a different button in Step 6 than what you used for the garage door opener. Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted.


Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell or terminate your lease. To erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1. Press and hold the two outside buttons at the same


time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly.


2. Once the indicator lights begin to blink, release both


buttons. The codes from all buttons will be erased. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-5.


2-55


Information Provided by: Storage Areas Glove Box To open the glove box, lift up on the lever.


Cupholder(s) Your vehicle may have cupholders located on and behind the center console and in the rear seat armrest. Pull the loop down on the rear seat armrest to access the cupholders.


Instrument Panel Storage Your vehicle may have an instrument panel storage area. It is located above the glove box.


To open, press and hold the driver’s side of the handle in and pull out on the exposed portion of the handle.


Pull downward on the lid to use the cupholders behind the center console.


2-56


Information Provided by: Center Console Storage Your vehicle may have an upper and lower center console storage area with cupholders.


Cargo Management System Your vehicle may have a cargo management system. It is located in the bed of the truck. The system contains three rails located on the front and sides of the bed. The system will include four adjustable cargo tie-downs. The tie-downs can be placed on the upper and lower slides of the rail.


To access the upper storage area, pull lever (A) up. To access the lower storage area, raise the upper storage bin, then pull lever (B) up. Use the key to lock and unlock the lower storage area.


Rear Seat Armrest Your vehicle may have a rear seat armrest that contains two cupholders. To access the cupholders, pull the armrest down from the rear seatback.


To adjust a tie-down, pull the locator pin out and move the tie-down to another location making sure the locator pin lines up with a locator hole on the rail. The tie-down pin may not be installed correctly if the pin does not line up, turn it over and reinstall. The tie-down will not move when the pin is installed completely. The maximum load for each rail is 500 lbs (227 kg).


2-57


Information Provided by: The rails are notched at each end which allows the tie-downs to be removed and placed on another rail. To remove, pull the locator pin out and slide the tie-down to the end of the rail and pull back. To remove or install cargo tie-downs at the front of the bed, slide the corner cap towards the center of the bed to expose the rail notches. To remove the corner cap, pull either edge away from the rail. To remove the system, loosen the toggle bolts on each rail until they can be removed from the bed of the truck. To replace the system, place the toggle bolts and rails into their original locations and tighten them to a torque setting of 12.5 ft-lbs (17Y). If the system is removed to install a bed liner, make sure there is no bed liner material in the installation points. Notice: If you tie down cargo using the horizontal slots on the top of the pickup box, you may damage the box. Using the horizontal slots on the top of the pickup box for tie-down locations may cause damage to the pickup box and would not be covered by your warranty. Only use the tie-down loops if you do not have the cargo management system.


2-58


Sunroof If your vehicle has a power sliding sunroof, the ignition needs to be turned to RUN, or the Retained Accessory Power (RAP) must be activated to open or close the sunroof. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until the driver’s door is opened. See Retained Accessory Power (RAP) on page 2-23 for more information.


There are two sunroof switches located in the overhead console above the rearview mirror.


Vent: From the closed position, press the rear of the passenger’s side switch to vent the sunroof. To close the sunroof, press and hold the front of the passenger’s side switch.


Information Provided by: Manual-Open/Manual-Close: To open the sunroof press and hold the rear of the driver’s side switch until the sunroof reaches the desired position. To close the sunroof, press and hold the front of the driver’s side switch until the sunroof reaches the desired position.


When the sunroof is opened, an air deflector will automatically raise. The air deflector will retract when the sunroof is closed.


Express-Open/Express-Close: To express-open the sunroof, fully press and release the rear of the driver’s side switch. The sunroof will open automatically. To stop the sunroof partway, press the switch a second time. To express-close the sunroof, fully press and release the front of the driver’s side switch. The sunroof will close automatically. To stop the sunroof partway, press the switch a second time.


The sunroof also has a sunshade which you can pull forward to block sun rays. The sunshade must be opened and closed manually.


Anti-Pinch Feature: If an object is in the path of the sunroof while it is closing, the anti-pinch feature will detect the object and stop the sunroof from closing at the point of the obstruction. The sunroof will then open halfway, and the air deflector will raise. To close the sunroof once it has re-opened, refer to the Express-Close or Manual-Close functions described previously. If the sunroof is in the vent position, and there is an object in the path of the sunroof when it closing, the anti-pinch feature will detect the object and stop the sunroof. To close the sunroof once it has re-opened, refer to the Manual-Close or Express-Close functions described previously.


2-59


Information Provided by: ✍ NOTES


2-60


Information Provided by: Section 3


Instrument Panel


Instrument Panel Overview ...............................3-4
Hazard Warning Flashers ................................3-6
Other Warning Devices ...................................3-6
Horn .............................................................3-6
Tilt Wheel .....................................................3-6
Turn Signal/Multifunction Lever .........................3-7
Turn and Lane-Change Signals ........................3-8
Headlamp High/Low-Beam Changer ..................3-8
Flash-to-Pass .................................................3-9
Windshield Wipers ..........................................3-9
Windshield Washer .......................................3-10
Cruise Control ..............................................3-11
Exterior Lamps .............................................3-14
Headlamps on Reminder ................................3-15
Daytime Running Lamps (DRL) .......................3-16
Automatic Headlamp System ..........................3-16
Puddle Lamps ..............................................3-17
Fog Lamps ..................................................3-17
Instrument Panel Brightness ...........................3-18
Dome Lamps ...............................................3-18
Dome Lamp Override ....................................3-18
Entry Lighting ...............................................3-18
Exit Lighting .................................................3-18
Reading Lamps ............................................3-19
Cargo Lamp .................................................3-19


Electric Power Management ...........................3-19
Battery Run-Down Protection ..........................3-20
Accessory Power Outlet(s) .............................3-20
Ashtray(s) and Cigarette Lighter ......................3-21
Climate Controls ............................................3-22


Climate Control System


(With Air Conditioning) ...............................3-22
Climate Control System (Heater Only) ..............3-24
Dual Automatic Climate Control System ...........3-26
Outlet Adjustment .........................................3-32
Warning Lights, Gages, and Indicators ............3-33
Instrument Panel Cluster ................................3-34
Speedometer and Odometer ...........................3-35
Trip Odometer ..............................................3-35
Tachometer .................................................3-35
Safety Belt Reminders ...................................3-36
Airbag Readiness Light ..................................3-37
Passenger Airbag Status Indicator ...................3-38
Charging System Light ..................................3-40
Voltmeter Gage ............................................3-40
Brake System Warning Light ..........................3-41
Antilock Brake System Warning Light ...............3-42
StabiliTrak® Indicator Light ..............................3-43
Engine Coolant Temperature Gage ..................3-43


3-1


Information Provided by: Section 3


Instrument Panel


Audio System(s) .............................................3-76
Setting the Clock ..........................................3-77
Radio(s) (MP3) .............................................3-79
Using an MP3


(Radio with Six-Disc Player) ........................3-97


Using an MP3


(Radio with CD and DVD Player) ...............3-102
XM Radio Messages ...................................3-107
Navigation/Radio System ..............................3-108
Rear Seat Entertainment (RSE) System .........3-109
Rear Seat Audio (RSA) ................................3-118
Theft-Deterrent Feature ................................3-120
Audio Steering Wheel Controls ......................3-120
Radio Reception .........................................3-121
Fixed Mast Antenna ....................................3-122
XM™ Satellite Radio Antenna System ............3-122


Tire Pressure Light .......................................3-44
Malfunction Indicator Lamp .............................3-44
Oil Pressure Gage ........................................3-48
Oil Pressure Light .........................................3-49
Security Light ...............................................3-49
Fog Lamp Light ............................................3-50
Cruise Control Light ......................................3-50
Highbeam On Light .......................................3-50
Tow/Haul Mode Light ....................................3-50
Fuel Gage ...................................................3-51
Driver Information Center (DIC) .......................3-52


DIC Operation and Displays


(Using DIC Buttons) ...................................3-52


DIC Operation and Displays


(Using Trip Odometer Reset Stem) ..............3-58
DIC Warnings and Messages .........................3-59
DIC Vehicle Customization (With DIC Buttons) ....3-68


3-2


Information Provided by: ✍ NOTES


3-3


Information Provided by: Instrument Panel Overview


United States version shown; Canada similar


3-4


Information Provided by: A. Air Outlets. See Outlet Adjustment on page 3-32. B. Turn Signal/Multifunction Lever. See Turn


Signal/Multifunction Lever on page 3-7.


C. Instrument Panel Cluster. See Instrument Panel


Cluster on page 3-34.


D. Hazard Warning Flasher Button. See Hazard


Warning Flashers on page 3-6.


E. Shift Lever. See Automatic Transmission Operation


on page 2-27.


F. Tow/Haul Selector Button (If Equipped).


See Tow/Haul Mode on page 2-31.


G. Driver Information Center Controls (DIC).


See Driver Information Center (DIC) on page 3-52. H. Audio System. See Audio System(s) on page 3-76. I. Exterior Lamps Control. See Exterior Lamps on


page 3-14.


J. Integrated Trailer Brake Controller (If Equipped).


See Towing a Trailer on page 4-41.


K. Dome Lamp Override Button. See Dome Lamp


Override on page 3-18. Dome Lamp Knob. See Dome Lamps on page 3-18.


L. Cruise Control Buttons. See Cruise Control on


page 3-11.


M. Hood Release. See Hood Release on page 5-11. N. Parking Brake. See Parking Brake on page 2-32.


O. Tilt Wheel Lever. See Tilt Wheel on page 3-6. P. Horn. See Horn on page 3-6. Q. Audio Steering Wheel Controls. See Audio Steering


Wheel Controls on page 3-120.


R. Climate Controls. See Climate Control System


(With Air Conditioning ) on page 3-22 or Climate Control System (Heater Only) on page 3-24 or Dual Automatic Climate Controls (If Equipped). See Dual Automatic Climate Control System on page 3-26.


S. Accessory Power Outlets. See Accessory Power


Outlet(s) on page 3-20. Cigarette Lighter (If Equipped). See Ashtray(s) and Cigarette Lighter on page 3-21.


T. StabiliTrak® Button (If Equipped). See StabiliTrak®


System on page 4-5. Pedal Adjust Button (If Equipped). See Adjustable Throttle and Brake Pedal on page 2-25. Rear Park Assist Disable Button (If Equipped). See Ultrasonic Rear Parking Assist (URPA) on page 2-43. Heated Windshield Washer Fluid Button (If Equipped). See Windshield Washer on page 3-10.


U. Passenger Airbag Off Control (If Equipped).


See Passenger Sensing System on page 1-63.


V. Glove Box. See Glove Box on page 2-56.


3-5


Information Provided by: Hazard Warning Flashers The hazard warning flashers warn others. They also let police know you have a problem.


The hazard warning flasher button is located on top of the steering column.


Press the button to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off. The hazard warning flashers work no matter what ignition position the key is in, and even if the key is not in the ignition. When the hazard warning flashers are on, your vehicle’s turn signals will not work.


Other Warning Devices If you carry reflective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle.


Horn To sound the horn, press the horn symbols located on the steering wheel.


Tilt Wheel The tilt wheel lets you adjust the steering wheel before you drive. Raise it to the highest level to give your legs more room when exiting or entering the vehicle.


3-6


Information Provided by: The tilt steering wheel lever is located on the lower left side of the steering column. To tilt the wheel, hold the steering wheel and pull the lever. Then move the steering wheel to a comfortable position and release the lever to lock the wheel in place.


Turn Signal/Multifunction Lever


The lever on the left side of the steering column includes the following: (cid:129) GTurn and Lane Change Signals. See Turn and


Lane-Change Signals on page 3-8.


(cid:129) 53Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-9.


(cid:129) NWindshield Wipers. See Windshield Wipers on


page 3-9.


(cid:129) LWindshield Washer. See Windshield Washer on


page 3-10.


For information on the exterior lamps, see Exterior Lamps on page 3-14.


3-7


Information Provided by:(cid:129) Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime sounds at each flash of the turn signal and the message TURN SIGNAL ON also appears in the Driver Information Center (DIC). Move the turn signal lever to the off position, to turn the chime and message off. Headlamp High/Low-Beam Changer 53(Headlamp High/Low Beam Changer): Push the lever toward the instrument panel, to change the headlamps from low to high beam.


Pull the multifunction lever toward you and release it, to return to low-beam headlamps.


When the high beams are on, this indicator light on the instrument panel cluster will also be on.


Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. Each position signals a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever returns automatically to the starting position. To signal a lane change, raise or lower the lever until the arrow starts to flash. Hold it there until your lane change is completed. The lever returns to the starting position by itself when it is released.


An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.


If the arrows flash more quickly than normal as you signal a turn or a lane change, a signal bulb might be burned out and other drivers will not see the turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not come on when you signal a turn, check for burned-out bulbs and a blown fuse. See Fuses and Circuit Breakers on page 5-108.


3-8


Information Provided by: Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, your high-beam headlamps turn on. They will stay on as long as you hold the lever toward you. The high-beam indicator on the instrument panel cluster comes on. Release the lever to return to normal operation.


Windshield Wipers Clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-57.


Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. Turn the band with the wiper symbol to control the windshield wipers. 8(Mist): Turn the band to mist for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers stop after one wipe. Hold the band on mist longer, for more wipe cycles. 9(Off): To stop the wipers, move the band to off. 6 (Delay): Turn the band to adjust the delay time. The delay between wiping cycles becomes shorter as the band is moved to the top of the lever. This can be very useful in light rain or snow. 6 (Low Speed): Turn the band away from you to the first solid band past the delay settings, for steady wiping at low speed.


? (High Speed): Turn the band further, to the second solid band past the delay settings, for high-speed wiping.


3-9


Information Provided by: Windshield Washer


{CAUTION:


In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.


L(Washer Fluid): Push the paddle marked with the windshield washer symbol at the top of the multifunction lever, to spray washer fluid on the windshield. The wipers clear the window and then either stop or return to the preset speed.


3-10


Heated Windshield Washer For vehicles with the heated windshield washer fluid system it can be used to help clear ice, snow, tree sap, or bugs from your windshield.


The button is located in the switchbank under the climate controls.


Push the heated washer fluid button to activate the heated windshield washer fluid system. The indicator light will flash. This activation initiates four heated wash/wipe cycles. The first heated wash/wipe cycle may take up to 40 seconds to occur, depending on outside temperature. After the first wash/wipe cycle, it may take up to 20 seconds for each of the remaining cycles to begin. Press the button again to turn off the heated windshield washer fluid system or it will automatically turn off after four wipe cycles have been completed. When the heated windshield washer fluid system is activated under certain outside temperature conditions, steam may flow out of the washer nozzles for a short period of time before washer fluid is sprayed. This is a normal condition.


Information Provided by: When you apply your brakes, cruise control is turned off. If your vehicle has the StabiliTrak® system and begins to limit wheel spin while you are using cruise control, the cruise control will automatically disengage. See StabiliTrak® System on page 4-5. When road conditions allow you to safely use it again, you may turn the cruise control back on.


Cruise Control


{CAUTION:


Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.


With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).


3-11


Information Provided by: The cruise control buttons are located on left side of the steering wheel.


Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low. The cruise control light on the instrument panel cluster will come on after the cruise control has been set to the desired speed.


{CAUTION:


If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.


1. Press the cruise control On/Off button. 2. Get up to the desired speed. 3. Press the SET− button located on the steering


wheel and release it.


4. Take your foot off the accelerator.


T (On/Off): This button can both activate and turn off the system. The indicator light is on when cruise control is on and turns off when cruise control is off.


+ RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. SET − (Set/Coast): Press this button to set the speed or make the vehicle decelerate. [ (Cancel): Press this button to cancel cruise control without erasing the set speed from memory.


3-12


Information Provided by: Resuming a Set Speed If you apply the brakes while the cruise control is set, the cruise control is disengaged. But it does not need to be reset. Once the vehicle speed reaches about 25 mph (40 km/h) or more, press the +RES button on the steering wheel. The vehicle will go back to the previous set speed and stay there.


Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:129) Press and hold the +RES button on the steering wheel until you reach your new desired speed, then release it. To increase vehicle speed in small increments, press the +RES button. Each time this is done, the vehicle will go about 1 mph (1.6 km/h) faster.


Reducing Speed While Using Cruise Control To reduce the vehicle speed while using cruise control: (cid:129) Press and hold the SET– button on the steering wheel until the desired lower speed is reached, then release it. To slow down in very small amounts, press the SET– button on the steering wheel briefly. Each time this is done, the vehicle will go about 1 mph (1.6 km/h) slower.


Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed.


3-13


Information Provided by:(cid:129) (cid:129) Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. While going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. While going downhill, you might have to brake or shift to a lower gear to keep the vehicle’s speed down. Of course, applying the brake turns off the cruise control. Many drivers find this to be too much trouble and do not use cruise control on steep hills.


Ending Cruise Control There are three ways to end cruise control: (cid:129) Step lightly on the brake pedal. (cid:129) Press the cancel button on the steering wheel. (cid:129) Press the On/Off button on the steering wheel.


Erasing Speed Memory When the cruise control or the ignition is turned off, the cruise control set speed memory is erased.


Exterior Lamps


The exterior lamps control is located on the instrument panel to the left of the steering wheel.


It controls the following systems: (cid:129) Headlamps


Taillamps


(cid:129) Parking Lamps


License Plate Lamps Instrument Panel Lights


The exterior lamps control has four positions: O(Off): Turn the control to this position to turn off the automatic headlamps and daytime running lamps (DRL). Turn the headlamp control to the off position again to turn the automatic headlamps or DRL back on.


For vehicles first sold in Canada, the off position will only work when the vehicle is shifted into PARK (P).


3-14


Information Provided by:(cid:129) (cid:129) (cid:129) When the headlamps are turned on while the vehicle is on, the headlamps turn off automatically 10 minutes after the ignition is turned off. When the headlamps are turned on while the vehicle is off, the headlamps will stay on for 10 minutes before automatically turning off to prevent the battery from being drained. Turn the headlamp control to off and then back to the headlamp on position to make the headlamps stay on for an additional 10 minutes. Push the turn signal/multifunction lever toward the instrument panel to change the headlamps from low beam to high beam. Headlamps on Reminder A reminder chime will sound when the headlamps or parking lamps are manually turned on and the ignition is off, in LOCK, ACCESSORY, or a door is open. Turn the light off, then back on, to stop the chime.


AUTO (Automatic): Turn the control to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:129) Parking Lamps


Instrument Panel Lights Taillamps License Plate Lamps


When the vehicle is turned off and the headlamps are in AUTO, the headlamps may automatically remain on for a set time. The time of the delay can be changed using the DIC. See Driver Information Center (DIC) on page 3-52. ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following:


Instrument Panel Lights Taillamps License Plate Lamps


2(Headlamps): Turn the control to this position to turn on the headlamps together with the following: (cid:129) Parking Lamps


Instrument Panel Lights Taillamps License Plate Lamps


3-15


Information Provided by:(cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system will come on when the following conditions are met:


The ignition is on. The exterior lamps control is in AUTO. The transmission is not in PARK (P). The light sensor determines it is daytime.


When the DRL are on, only the DRL lamps will be on. The taillamps, sidemarker, and other lamps will not be on. The instrument panel will not be lit up either. When it begins to get dark, the automatic headlamp system will switch from DRL to the headlamps. To turn off the DRL lamps, turn the exterior lamps control to the OFF position and then release. For vehicles first sold in Canada, the transmission must be in the PARK (P) position, before the DRL lamps can be turned off.


3-16


Automatic Headlamp System When it is dark enough outside, the automatic headlamp system will turn on the headlamps at the normal brightness, along with the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. To turn off the automatic headlamp system, turn the exterior lamps switch to the off position and then release it. For vehicles first sold in Canada, the transmission must be in the PARK (P) position, before the automatic headlamp system can be turned off. The vehicle has a light sensor located on the top of the instrument panel in the defroster grille that regulates when the automatic headlamps turn on. Be sure it is not covered, or the headlamps will come on whenever the ignition is on. The system may also turn on the headlamps when driving through a parking garage, heavy overcast weather, or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay.


Information Provided by:(cid:129) (cid:129) (cid:129) (cid:129) If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it takes approximately one minute for the automatic headlamp system to change to DRL if it is bright enough outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-18. To idle the vehicle with the automatic headlamp system off, turn the control to the off position. The headlamps will also stay on after you exit the vehicle. This feature can be programmed using the Driver Information Center (DIC). See DIC Vehicle Customization (With DIC Buttons) on page 3-68. The regular headlamp system can be turned on when needed.


Puddle Lamps If your vehicle has puddle lamps, they come on when the unlock button on the Remote Keyless Entry (RKE) Transmitter is pressed. The lamps time out or turn off once the engine is started.


Fog Lamps The vehicle’s fog lamps provide better visibility in foggy or misty conditions.


The fog lamp button is located on the left side of the instrument panel.


The parking lamps and/or low-beam headlamps must be on for the fog lamps to work. Press the button to turn the fog lamps on while the headlamps are on. Press the button again to turn them off. An indicator light in the button comes on when the fog lamps are in use. Remember, fog lamps alone do not give off as much light as the headlamps. Never use the fog lamps in the dark without turning on the headlamps. The fog lamps go off whenever the high-beam headlamps come on. When the high beams turn off, the fog lamps come on again.


3-17


Information Provided by: The fog lamps are cancelled after the ignition is turned off. If you still want to use the fog lamps after the vehicle is restarted, press the fog lamp button again. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness D(Instrument Panel Brightness): This feature controls the brightness of the instrument panel lights and is located next to the exterior lamp control.


Push the knob to extend out and then it can be turned.


Turn the knob clockwise or counterclockwise to brighten or dim the instrument panel lights. Turning the knob to the farthest clockwise position turns on the dome lamps.


Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located next to the exterior lamps control, clockwise to the farthest position. In this position, the dome lamps remain on whether a door is opened or closed.


3-18


Dome Lamp Override The dome lamp override button is located next to the exterior lamps control.


k (Dome Off): Press the button in and the dome lamps remain off when a door is opened. Press the button again to return it to the extended position so that the dome lamps come on when a door is opened.


Entry Lighting Your vehicle has an illuminated entry feature. When a door is opened, the dome lamps and puddle lamps come on if the dome override feature is not in use. If the dome override feature is used, the lamps do not come on.


Exit Lighting The interior lamps come on when the key is removed from the ignition. They turn off automatically in 20 seconds. The lights do not come on if the dome override button is pressed in.


Information Provided by: Reading Lamps If your vehicle has reading lamps they are located on the overhead console. To turn on the reading lamps, press the button located next to each lamp. To turn them off, press the button again. Your vehicle may also have reading lamps in other locations. To turn the lamps on or off, press the button located next to the lamp. If your vehicle has a DVD Rear Seat Entertainment (RSE) system, press the lamp lenses to turn the lamps on or off. The lamps are fixed and cannot be adjusted.


Cargo Lamp The cargo lamps come on by turning the instrument panel brightness control knob to the farthest clockwise position. This knob is located on the instrument panel and also turns on the dome lamps. The cargo lamp can be used if more light is needed in the cargo area of the vehicle or in the top-box storage units.


Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets.


3-19


Information Provided by: EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-59.


Battery Run-Down Protection This feature shuts off the dome and reading lamps, if they are left on for more than 10 minutes after the ignition is turned off. The cargo lamp shuts off after 20 minutes. This prevents the battery from running down.


Accessory Power Outlet(s) Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone or CB radio. There are two accessory power outlets on the instrument panel, one inside the center floor console and one on the rear of the center floor console. To access the accessory power outlet inside the center floor console, press the button on the side of the console door. See Center Console Storage on page 2-57 for more information. To use an accessory power outlet, remove the protective cap. When not in use, always cover the accessory power outlet with the protective cap. Notice: power outlet, the battery may drain causing your vehicle not to start or damage to the battery. This would not be covered by the warranty. Always unplug all electrical devices when turning off your vehicle.


If electrical devices are left plugged into a


3-20


Information Provided by: Certain electrical accessories are not compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on accessory power outlets. The accessory power outlets are powered, even when the ignition is in LOCK/OFF. Continuing to use power outlets while the ignition is in LOCK/OFF may cause the vehicle’s battery to run down. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.


Improper use of the power outlet can cause


If you put papers, pins, or other flammable


Ashtray(s) and Cigarette Lighter Your vehicle may have a front ashtray located near the center of the instrument panel. Pull on the door to open it. The ashtray may have a cigarette lighter. Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put flammable items in the ashtray. To remove the ashtray, open the door and pull the ashtray bin toward you. To replace the ashtray, insert the ashtray bin inside the ashtray door and press down until it engages. To use the cigarette lighter, push it in all the way, and let go. When it is ready for use, the lighter pops back out. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.


3-21


Information Provided by: Climate Controls Climate Control System (With Air Conditioning) With this system you can control the heating, cooling, and ventilation for your vehicle.


Operation 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the front system off. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle.


3-22


Use the right knob to select from the following modes: The right knob can be positioned between two modes to select a combination of those two modes. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode directs half of the air to the instrument panel outlets and half to the floor outlets. 6(Floor): This mode directs most of the air to the floor outlets with some air directed to the windshield and side window outlets. In this mode, the system will automatically select outside air. Recirculation cannot be selected in floor mode. The right knob may also be used to select the defrost and defog mode. For more information, see “Defogging and Defrosting” later in this section. : (Outside Air): Press this button to turn the outside air mode on. When the button is pressed, an indicator light will come on. When this mode is on, outside air will circulate throughout the vehicle. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. ?(Recirculation): Press this button to turn the recirculation mode on. When the button is pressed, an indicator light will come on.


Information Provided by: This mode keeps outside air from entering the vehicle. It can be used to reduce outside air and prevent odors from entering the vehicle. Recirculation may also help cool the air inside the vehicle more quickly once the temperature inside the vehicle is less than the outside temperature. The recirculation mode cannot be used with floor, defog or defrost modes. If recirculation is selected with one of these modes, the indicator light will flash three times and then turn off. While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed. The recirculation mode can be turned off by pressing the outside air button, or by turning off the ignition. #(Air Conditioning): Press this button to turn the air conditioning system on or off. When this button is pressed, an indicator light on the button will come on to let you know the air conditioning is activated. The air conditioning can be selected in any mode as long as the fan switch is on. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal.


Defogging and Defrosting Fog or frost on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. To avoid fogging windows on rainy and humid days at temperatures above freezing, run the air conditioning compressor. It is best to avoid the use of the recirculation mode, except when maximum A/C performance is needed or for short times to avoid exterior odors. Turn the right knob to select the defog or defrost mode. -(Defog): This mode clears the windows of fog or moisture and warm the passengers. The air is directed to the windshield, floor outlets, and side window vents. 0(Defrost): This mode removes fog or frost from the windshield more quickly. A portion of the air is directed to the windshield and the side window vents, with some air directed to the floor vents. The system will automatically force outside air into the vehicle. The recirculation mode cannot be selected in the defog or defrost mode. When either mode is selected, the system runs the air conditioning compressor, unless the outside temperature is close to freezing. Do not drive the vehicle until all the windows are clear.


3-23


Information Provided by: Rear Window Defogger If your vehicle has a rear window defogger it uses a warming grid to remove fog from the rear window. The rear window defogger will only work when the ignition is in RUN. <(Rear): Press this button to turn the rear window defogger on or off. An indicator light on the button will come on to let you know that the rear window defogger is activated. The rear window defogger will only work when the ignition is in RUN. The rear window defogger will stay on for approximately 10 minutes after the button is pressed, unless the ignition is turned to ACC or LOCK. The defogger can also be turned off by pressing the button again or by turning off the engine. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid.


3-24


Climate Control System (Heater Only) With this system you can control the heating and ventilation for your vehicle.


Operation 9(Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the front system off.


Information Provided by: Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. Use the right knob to select from the following modes: The right knob can be positioned between two modes to select a combination of those two modes. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode directs half of the air to the instrument panel outlets and to the floor outlets. 6(Floor): This mode directs most of the air to the floor outlets with some air directed to the windshield, side window outlets, and second row floor outlets. In this mode, the system will automatically select outside air.


Defogging and Defrosting Fog or frost on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. Turn the right knob to select the defog or defrost mode. -(Defog): This mode clears the windows of fog or moisture and warm the passengers. The air is directed to the windshield, floor outlets, and side window vents. 0(Defrost): This mode removes fog or frost from the windshield more quickly. A portion of the air is directed to the windshield and the side window vents, with some air directed to the floor vents. The system will automatically force outside air into the vehicle. Do not drive the vehicle until all the windows are clear.


3-25


Information Provided by: Driver and Passenger Side Temperature Controls The driver and passenger side temperature buttons are used to adjust the temperature of the air coming through the system on the driver or passenger’s side of the vehicle. The temperature can be adjusted even if the system is turned off. This is possible since outside air always flows through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Press the + or − buttons to increase or decrease the cabin temperature. The driver side or passenger side temperature display shows the temperature setting decreasing or increasing. The passenger’s temperature setting can be set to match the driver’s temperature setting by pressing the PASS button and turning off the PASS indicator. When the passenger’s temperature setting is set different than the driver’s setting, the indicator on the PASS button illuminates and both the driver’s side and passenger’s side temperature displays are shown.


Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. The vehicle also has a flow-through ventilation system described later in this section.


Different climate control settings can be selected for the driver and passengers.


3-26


Information Provided by: Automatic Operation


AUTO (Automatic): When automatic operation is active the system controls the inside temperature, the air delivery, and the fan speed. Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button.


When AUTO is selected, the display changes to show the current temperature(s) and AUTO is lit on the display. The current air delivery mode and fan speed are also displayed for about 5 seconds. When AUTO is selected, the air conditioning operation and air inlet are automatically controlled. The air conditioning compressor may run when the outside temperature is above freezing. The air inlet will normally be set to outside air. If it is hot outside, the air inlet may automatically switch to the recirculate mode to help quickly cool down the air inside the vehicle. The light on the button comes on in recirculation.


2. Set the driver’s and passenger’s temperature.


To find your comfort setting, start with a 74°F (23°C) temperature setting and allow about 20 minutes for the system to regulate. Use the driver’s or passenger’s temperature buttons to adjust the temperature setting as necessary. If you choose the temperature setting of 60°F (15°C), the system remains at the maximum cooling setting. If you choose the temperature setting of 90°F (32°C), the system remains at the maximum heat setting. Choosing either maximum setting will not cause the vehicle to heat or cool any faster.


Be careful not to cover the solar sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on sun load. For more information on the solar sensor, see “Sensors” later in this section.


3-27


Information Provided by: To avoid blowing cold air in cold weather, the system delays turning the fan on until warm air is available. The length of delay depends on the engine coolant temperature. Pressing the fan switch overrides this delay and changes the fan to a selected speed. O(On/Off): Press this button to turn off the climate control system. Outside air still enters the vehicle, and is directed to the floor. This direction can be changed by pressing the mode button. Recirculation can be selected once you have selected vent or bi-level mode. The temperature can also be adjusted using either temperature button. If the air delivery mode or temperature settings are adjusted with the system off, the display illuminates briefly to show the settings and then returns to off. Press the on/off button or the up down arrows on the fan switch, the defrost button, AUTO button, or the air conditioning button to turn the system on when it is off.


Manual Operation The air delivery mode or fan speed can be manually adjusted. DC (Fan): These buttons let you manually adjust the fan speed. Press D to increase fan speed and C to decrease fan speed. Pressing either fan button while the system is off turns the system on. Pressing either fan button while in automatic control places the fan under manual control. The fan setting remains displayed and the AUTO light turns off. The air delivery mode remains under automatic control. HG (Mode): Press H and G to manually change the direction of the airflow in the vehicle. Repeatedly press either button until the desired mode appears on the display. Pressing either mode button while the system is off changes the air delivery mode without turning the system on. Pressing either mode button while in automatic control places the mode under manual control.


The air delivery mode setting is displayed and the AUTO light turns off. The fan remains under automatic control.


3-28


Information Provided by: H(Vent): Air is directed to the instrument panel outlets. )(Bi-Level): Air is directed partly to the instrument panel outlets and to the floor outlets. A little air is directed towards the windshield and side window outlets. Cooler air is directed to the upper outlets and warmer air to the floor outlets. 6(Floor): Air is directed to the floor outlets, with some to the windshield, side window outlets, and second row floor outlets. In this mode, the system will automatically select outside air. -(Defog): See “Defogging and Defrosting” later in this section. @(Recirculation): Press this button to turn the recirculation mode on. When the button is pressed, an indicator light comes on.


This mode keeps outside air from entering the vehicle. It can be used to reduce outside air and prevent odors from entering the vehicle. Recirculation may also help cool the air inside the vehicle more quickly once the temperature inside the vehicle is less than the outside temperature.


The recirculation mode cannot be used with floor, defog, or defrost modes. If recirculation is selected with one of those modes, the indicator light flashes three times and then turns off. The air conditioning compressor also comes on when this mode is activated. While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed.


The recirculation mode can be turned off by pressing the outside air button, or by turning off the ignition. ; (Outside Air): Press this button to turn on the outside air mode. When this mode is selected, air from outside the vehicle circulates throughout the vehicle. An indicator light on the button comes on to show that it is activated. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode.


3-29


Information Provided by: Sensors


Air Conditioning # (Air Conditioning): Press this button to turn the air conditioning (A/C) compressor on and off. When air conditioning is selected, an indicator light comes on to show that the air conditioning has been activated.


Pressing this button when the outside temperature is too cool for air conditioning makes the air conditioning indicator flash three times and then turn off to let you know the air conditioning mode is not available. If the air conditioning is on and the outside temperature drops below a temperature which is too cool for air conditioning to be effective, the air conditioning light turns off to show that the air conditioning mode has been canceled. On hot days, open the windows long enough to let hot inside air escape. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. The air conditioning system removes moisture from the air, so a small amount of water might drip underneath the vehicle while idling or after turning off the engine. This is normal.


3-30


The solar sensor, located in the defrost grille, in the middle of the instrument panel, monitors the solar radiation. Do not cover the solar sensor or the system will not work properly.


The interior temperature sensor, located in the headliner, measures the temperature of the air inside the vehicle.


Information Provided by: There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature on the rearview mirror. The climate control system uses the information from these sensors to maintain your comfort setting by adjusting the outlet temperature, fan speed, and the air delivery mode. The system may also supply cooler air to the side of the vehicle facing the sun. The recirculation mode will also be used as needed to maintain cool outlet temperatures.


Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from the windshield. Use H and G to select the defog or defrost modes.


- (Defog): Press this button to clear the windows of fog or moisture and warm the passengers. This mode directs air to the windshield, floor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is close to freezing. The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 0 (Defrost): Press this button to remove fog or frost from the windshield more quickly. This mode directs a portion of the air to the windshield and side window vents and some to the floor vents. In this mode, the system will automatically force outside air into your vehicle. The recirculation mode cannot be selected while in the defrost mode. The air conditioning compressor will run automatically in this setting, unless the outside temperature is close to freezing. Do not drive the vehicle until all the windows are clear.


3-31


Information Provided by: Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <(Rear Window Defogger): If your vehicle has this feature, press this button to turn the defogger on or off. It automatically turns off several minutes after it has been activated. The defogger can also be turned off by turning the engine off. Do not drive the vehicle until all the windows are clear. Notice: Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by your warranty.


Heated Mirrors: If your vehicle has heated outside rearview mirrors, the mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defog button is pressed. See Outside Power Mirrors on page 2-39.


Outlet Adjustment Use the air outlets located in the center and on the side of the instrument panel to direct the airflow. Operation Tips (cid:129) Clear away any ice, snow, or leaves from air inlets at the base of the windshield that could block the flow of air into your vehicle.


(cid:129) Keep the path under the front seats clear of objects


to help circulate the air inside of the vehicle more effectively.


(cid:129) Use of non-GM approved hood deflectors can adversely affect the performance of the system. Check with your dealer/retailer before adding equipment to the outside of your vehicle.


3-32

Loading...
x