Download PDF Manual

Safety Belt Reminders on page 3-30 for more information. Keep safety belts clean and dry. See Care of Safety Belts on page 5-106.


1-70


If the vehicle has the LATCH system and it was being used during a crash, you may need new LATCH system parts. New parts and repairs may be necessary even if the safety belt or LATCH system (if equipped), was not being used at the time of the crash. If an airbag inflates, you will need to replace airbag system parts. See the part on the airbag system earlier in this section. Have the safety belt pretensioners checked if the vehicle has been in a crash, if the airbag readiness light stays on after the vehicle is started, or while you are driving. See Airbag Readiness Light on page 3-31.


Replacing Restraint System Parts After a Crash


{ CAUTION:


A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.


If the vehicle has been in a crash, do you need new safety belts or LATCH system (if equipped) parts? After a very minor crash, nothing may be necessary. But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer/retailer to have the safety belt assemblies inspected or replaced.


1-71


✍ NOTES


1-72


Section 2


Features and Controls


Keys ...............................................................2-3
Remote Keyless Entry (RKE) System ................2-4
Remote Keyless Entry (RKE) System


Operation ...................................................2-5
Doors and Locks .............................................2-7
Door Locks ....................................................2-7
Power Door Locks ..........................................2-8
Delayed Locking .............................................2-8
Programmable Automatic Door Locks ................2-9
Rear Door Security Locks ..............................2-11
Lockout Protection ........................................2-11
Liftgate/Liftglass ............................................2-12
Windows ........................................................2-13
Power Windows ............................................2-14
Sun Visors ...................................................2-15
Theft-Deterrent Systems ..................................2-16
Content Theft-Deterrent .................................2-16
Passlock® (U.S. Only) ...................................2-17
PASS-Key® III+ Electronic Immobilizer .............2-18
PASS-Key® III+ Electronic Immobilizer


Operation (Canada Only) ............................2-18


Starting and Operating Your Vehicle ................2-20
New Vehicle Break-In ....................................2-20
Ignition Positions ..........................................2-21
Retained Accessory Power (RAP) ...................2-22
Starting the Engine .......................................2-22
Adjustable Throttle and Brake Pedal ................2-23
Engine Coolant Heater ..................................2-24
Active Fuel Management™ .............................2-25
Automatic Transmission Operation ...................2-25
Four-Wheel Drive ..........................................2-28
Parking Brake ..............................................2-33
Shifting Into Park ..........................................2-34
Shifting Out of Park ......................................2-36
Parking Over Things That Burn .......................2-36
Engine Exhaust ............................................2-37
Running the Vehicle While Parked ..................2-38
Mirrors ...........................................................2-39
Manual Rearview Mirror .................................2-39
Automatic Dimming Rearview Mirror ................2-39
Compass .....................................................2-40
Outside Manual Mirrors ..................................2-41
Outside Power Mirrors ...................................2-42
Outside Convex Mirror ...................................2-42
Outside Heated Mirrors ..................................2-42


2-1


Section 2


Features and Controls


OnStar® System .............................................2-43
Universal Home Remote System ......................2-46


Universal Home Remote System Operation


(With One Triangular LED) .........................2-47
Storage Areas ................................................2-51
Glove Box ...................................................2-51
Overhead Console ........................................2-51
Center Console Storage .................................2-52


Luggage Carrier ...........................................2-52
Rear Floor Storage Cover ..............................2-53
Convenience Net ..........................................2-54
Cargo Cover ................................................2-54
Cargo Tie Downs ..........................................2-55
Sunroof .........................................................2-55


2-2


Keys


{ CAUTION:


Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window. Do not leave the keys in a vehicle with children.


This vehicle has keys that can be used for the ignition and door lock that will fit with either side up. When a new vehicle is delivered, the dealer/retailer provides the owner with a pair of identical keys and a key code number.


2-3


The key code number tells your dealer/retailer or a qualified locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you will be able to have new ones made easily using this number. Your selling dealer/retailer should also have this number. Notice: you may have to damage the vehicle to get in. Be sure you have spare keys. If you ever get locked out of your vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-7.


If you ever lock your keys in the vehicle,


Remote Keyless Entry (RKE) System If this vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received,


including interference that may cause undesired operation of the device.


2-4


This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received,


including interference that may cause undesired operation of the device.


Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment. If there is a decrease in the RKE operating range, try this: (cid:129) Check the distance. The transmitter may be too far


from the vehicle. Stand closer during rainy or snowy weather.


(cid:129) Check the location. Other vehicles or objects may


be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again.


(cid:129) Check the transmitter’s battery. See “Battery


Replacement” later in this section. If the transmitter is still not working correctly, see your dealer/retailer or a qualified technician for service.


(cid:129) Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 30 feet (9 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-4.


K (Unlock): Press once to unlock the driver door. The parking lamps flash and the interior lights come on. Press K a second time within three seconds to unlock all the doors.


Q (Lock): Press to lock all the doors. Press Q again within three seconds and the horn chirps. L (Panic): Press to sound the horn. The headlamps and taillamps flash for up to 30 seconds. To turn it off, press L again, or wait 30 seconds, or start the vehicle. Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed. Any lost or stolen transmitters no longer work once the new transmitter is programmed. Each vehicle can have up to four transmitters programmed to it.


To program different feedback settings through the Driver Information Center (DIC), see Driver Information Center (DIC) on page 3-47.


2-5


To replace the battery:


Battery Replacement Replace the battery if the KEY FOB # BATTERY LOW message displays in the DIC. See “KEY FOB # BATTERY LOW” under DIC Warnings and Messages on page 3-51 for additional information. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter.


1. Separate the transmitter with a flat, thin object inserted into the slot between the covers of the transmitter housing.


2. Remove the old battery. Do not use a metal object. 3. Insert the new battery. Replace with a CR2032


or equivalent battery.


4. Snap the transmitter back together.


2-6


Doors and Locks


Door Locks


{ CAUTION:


There are several ways to lock and unlock your vehicle. You can use the remote keyless entry system. You can use your key to unlock your door from the outside.


Unlocked doors can be dangerous.


(cid:129) Passengers, especially children, can easily


open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive.


(cid:129) Young children who get into unlocked vehicles


may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it.


(cid:129) Outsiders can easily enter through an


unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening.


You can lock or unlock the door from the inside by sliding the manual lever forward or rearward. When the door is unlocked, you can see a red area on the lever. The manual lever on each door works only that door’s lock.


2-7


Power Door Locks


The power door lock switches are located on the driver’s and front passenger’s door armrests.


Press the lock symbol to lock all of the doors. To unlock the doors, press the other side of the switch.


Delayed Locking This feature delays the locking of the doors and the liftgate when using the power lock or the remote keyless entry system. The first press of the power door lock switch or lock button on the remote keyless entry transmitter with the driver’s door open will activate the delay locking. A chime will sound. All doors and the liftgate can be reopened for up to five seconds from the time the last door is closed. Five seconds after the last door is closed, all the doors will lock. You can lock the doors immediately by using the power door lock switch or by pressing the lock button on the optional remote keyless entry transmitter a second time. If the key is inserted in the ignition, this feature will not lock the doors. See Lockout Protection on page 2-11. You can turn the delayed locking feature on or off. If the feature is turned off, the doors will lock immediately when a power door lock switch or remote keyless entry transmitter lock button is pressed.


2-8


Programming Delayed Locking To turn the delayed locking feature on or off, do the following: 1. Press and hold the power door lock switch on the


driver’s door in the lock position.


2. Press the remote keyless entry transmitter unlock


button twice.


If the delayed locking feature was on, it will now be off. If the feature was off, it will now be on.


Programmable Automatic Door Locks Your vehicle is equipped with an automatic lock/unlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC), or by the following method. See DIC Vehicle Customization on page 3-56. Programmable Locking Feature Following are the two locking modes that can be programmed: Mode 1: All doors lock when the transmission is shifted out of (P) Park. Mode 2: All doors lock when the vehicle speed is greater than 8 mph (13 km/h).


The automatic door locks were pre-programmed at the factory to lock all the doors when the transmission is shifted into gear. The following instructions detail how to program your door locks differently than the factory setting. Choose one of the two programming options listed previously before entering the program mode. To enter the program mode, do the following: 1. Begin with the ignition off. Then pull the turn


signal/multifunction lever toward you and hold it there while you perform the next step.


2. Turn the key to ON/RUN and LOCK/OFF twice.


Then, with the key in LOCK/OFF, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin.


3. You are now ready to program the automatic door locks. Select one of the two programming options listed previously, and press the lock side of the power door lock switch to cycle through the lock options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode.


2-9


You can exit the program mode any time by turning the ignition to ON/RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modified. See your dealer for more information. Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into (P) Park. Mode 2: All doors unlock when the transmission is shifted into (P) Park. Mode 3: All doors unlock when the key is removed from the ignition. Mode 4: No automatic door unlock. The automatic door locks were pre-programmed at the factory to unlock all doors once the transmission is shifted to (P) Park. The following instructions detail how to program your door locks differently than the factory setting. Choose one of the four programming options listed previously before entering the program mode.


2-10


To enter the program mode you need to do the following: 1. Begin with the ignition off. Then pull the turn signal/


multifunction lever toward you and hold it there while you perform the next step.


2. Turn the key to ON/RUN and LOCK/OFF twice.


Then, with the key in LOCK/OFF, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin.


3. You are now ready to program the automatic door locks. Select one of the four programming options listed above, and press the unlock side of the power door lock switch to cycle through the unlocking options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode.


You can exit the program mode any time by turning the ignition to ON/RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modified. See your dealer for more information.


Rear Door Security Locks Your vehicle may have this feature. You can lock the rear doors so they cannot be opened from the inside by passengers. To use one of these locks do the following: 1. Open one of the rear doors. You will find a


security lock lever located on the inside edge of each rear door.


2. Move the lever down to


engage the security lock. Move the lever up to disengage the security lock.


The rear doors of your vehicle cannot be opened from the inside while this feature is in use. If you want to open the rear door while the security lock is on, unlock the door and open the door from the outside.


Lockout Protection This feature stops the power door locks from locking when the key is in the ignition and a door is open to protect you from locking your key in the vehicle. If the power lock switch is pressed when a door is open and the key is in the ignition, all the doors will lock and then the driver’s door will unlock.


3. Close the door.


2-11


Liftgate/Liftglass


{ CAUTION:


It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate or liftglass:


(cid:129) Make sure all other windows are shut. (cid:129) Turn the fan on your climate control system to its highest speed and select the control setting that will force outside air into your vehicle. See “Climate Control System” in the Index. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-37.


Liftgate Release To unlock the liftgate, use the power door lock switch or the remote keyless entry transmitter. See Remote Keyless Entry (RKE) System Operation on page 2-5. The liftglass will also unlock when the liftgate is unlocked. Press the button on the liftglass to open it. To open the entire liftgate, lift the handle located in the center of the liftgate. When the liftgate is opened, the liftglass will lock after a short delay. Emergency Release for Opening Liftgate 1. Remove the trim plug, located on the inside of the liftgate in the center, to expose the access hole in the trim panel.


2. Use a tool to reach through the access hole in the


trim panel.


3. Pry the left release lever up to the unlock position. Pry the right release lever up to unlatch the liftgate.


4. Reinstall the trim plug.


2-12


(cid:129) Windows


{ CAUTION:


Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.


2-13


Power Windows


{ CAUTION:


Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows.


2-14


The controls for the power windows are located on the armrest on each of the side doors. With power windows, the switches operate the windows when the ignition is in ON/RUN, ACC/ACCESSORY or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-22. The driver’s door also has a switch for each of the passenger’s windows. Press down the top of the switch to lower the window and pull up on the switch to raise the window. If you hold the switch down for three to seven seconds after the window has been completely lowered or raised, the window will not operate for about 15 seconds.


Express-Down Window


AUTO (Express-down): The driver’s and front passenger’s window switches have an express-down feature that allows you to lower the window without holding the switch down. Press down briefly on the driver’s or front passenger’s window switch labeled AUTO to activate the express-down feature. Lightly tap the switch to open the window slightly. The express-down feature can be interrupted at any time by pressing the top of the switch. Window Lockout


o (Lockout): Your vehicle has a lockout feature to prevent passengers from operating the power windows. The lockout switch is located in front of the window switches on the driver’s door. A light in the lockout switch will come on to show that the switch has been activated. Press the lockout switch again to return to normal operation.


Sun Visors Sun Visors with Slide Rod Your vehicle may have this feature. Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window. Swing the sun visor to the side to cover the side window. It can also be moved along the rod from side-to-side in this position. Sun Visors with Fixed Rod and Pull-out Extension Your vehicle may have this feature. Pull the sun visor down to block glare. Pull the sun visor extender out for additional coverage. Detach the sun visor from the center mount and swing it to the side to cover the side window. Visor Vanity Mirror Pull the sun visor down to expose the vanity mirror. You may have to lift a cover to expose the mirror. Lighted Visor Vanity Mirror Your vehicle may have this feature. Pull the sun visor down and lift the mirror cover to turn on the lamps. The lamps will turn off when the cover is closed.


2-15


3. Close all doors. The security light should turn off after about 30 seconds. The alarm is not armed until the security light turns off.


If a locked door is opened without the key or the RKE transmitter, the alarm will go off. The headlamps and parking lamps will flash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power. To avoid setting off the alarm by accident: (cid:129) Always lock the vehicle using the door key after the


doors are closed.


(cid:129) Always unlock a door with a key, or use the RKE


transmitter. Unlocking a door any other way will set off the alarm.


To turn off the alarm, press unlock on the RKE transmitter or unlock any door with the key.


Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal.


Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system.


The security light is located on the instrument panel cluster.


To operate the system:


1. Open the door. 2. Lock the door with the power door lock switch or the Remote Keyless Entry (RKE) transmitter. The security light should flash. The system will not activate if the doors are locked with the key or manual door lock.


2-16


Testing the Alarm To test the alarm: 1. From inside the vehicle, lower the driver’s window


and open the driver’s door.


2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the RKE transmitter.


3. Get out of the vehicle, close the door and wait for


the security light to go out.


4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm.


When the alarm is set the power door unlock switch will not work. If the alarm does not sound when it should but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 5-113. If the alarm does not sound or the headlamps do not flash, the vehicle should be serviced by your dealer/retailer.


Passlock® (U.S. Only) Your vehicle has the Passlock theft-deterrent system. Passlock is a passive theft-deterrent system that enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder has been tampered with, the fuel system is disabled and the vehicle will not start. During normal operation, the security light will turn off about five seconds after the key is turned to ON/RUN. If the engine stalls and the security light flashes, wait about 10 minutes until the light stops flashing before trying to restart the engine. Remember to release the key from START as soon as the engine starts. If the engine does not start after three tries, the vehicle needs service. If the engine is running and the security light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock system is not working properly and must be serviced by your dealer/retailer. Your vehicle is not protected by Passlock at this time. You may also want to check the fuse. See Fuses and Circuit Breakers on page 5-113. See your dealer/retailer for service. In an emergency, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-7. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.


2-17


PASS-Key® III+ Electronic Immobilizer The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received,


including interference that may cause undesired operation.


This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received,


including interference that may cause undesired operation of the device.


Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key III+ uses a radio frequency transponder in the key that matches a decoder in the vehicle.


2-18


PASS-Key® III+ Electronic Immobilizer Operation (Canada Only) Your vehicle has a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system. The key uses a transponder that matches an immobilizer control unit in your vehicle. Only the correct key will start the vehicle. If the key is ever damaged, you may not be able to start your vehicle. When trying to start the vehicle, if the engine does not start and the security light comes on, there may be a problem with your theft-deterrent system. Turn the ignition off and try again.


If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 5-113. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the first key may be faulty. See your dealer/retailer who can service the theft-deterrent system and have a new key made. It is possible for the theft-deterrent system decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. The following procedure is for programming additional keys only.


Canadian Owners: If you lose or damage your keys, only a dealer/retailer can service the theft-deterrent system to have new keys made. To program additional keys you will require two current driver’s keys. To program a new key do the following: 1. Verify that the new key has PK3+ stamped on it. 2. Insert the current driver’s key in the ignition


and start the engine. If the engine will not start see your dealer/retailer for service.


3. After the engine has started, turn the key to


LOCK/OFF, and remove the key.


4. Insert the second current driver’s key in the ignition and start the engine within ten seconds of removing the previous key. If the engine will not start see your dealer/retailer for service.


5. After the engine has started, turn the key to LOCK/


OFF, and remove the key. Insert the key to be programmed and turn it to ON within ten seconds of removing the previous key. The security light will turn off once the key has been programmed.


6. Repeat the Steps 1 through 5 if additional keys are


to be programmed.


If the security light comes on and stays on while driving, you will be able to restart the engine if you turn it off. The theft-deterrent system, however, is not working properly and must be serviced by your dealer/retailer. Your vehicle is not protected by the theft-deterrent system at this time. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 7-7. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.


2-19


Starting and Operating Your Vehicle


New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:129) Keep your speed at 55 mph (88 km/h) or less for


the first 500 miles (805 km).


(cid:129) Do not drive at any one constant speed, fast or


slow, for the first 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake or slow the vehicle.


(cid:129) Avoid making hard stops for the first 200 miles (322 km) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:129) Do not tow a trailer during break-in. See Towing


a Trailer on page 4-46 for the trailer towing capabilities of the vehicle and more information.


Following break-in, engine speed and load can be gradually increased.


2-20


Ignition Positions


The ignition switch has four different positions.


Press the brake pedal, and turn the ignition to ON/RUN to shift out of P (Park). Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer.


A (LOCK/OFF): This position locks the ignition and transmission. The key can only be removed in LOCK/OFF.


The steering can bind with the wheels turned off center. If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY. If this doesn’t work, then the vehicle needs service.


B (ACC/ACCESSORY): This is the position in which you can operate electrical accessories.


C (ON/RUN): This position can be used to operate the electrical accessories and to display some instrument panel warning and indicator lights. The switch stays in this position when the engine is running.


If you leave the key in the ACC/ACCESSORY or ON/RUN position with the engine off, the battery could be drained. You may not be able to start the vehicle if the battery is allowed to drain for an extended period of time.


D (START): This is the position that starts the engine. When the engine starts, release the key. The ignition switch returns to ON/RUN for driving.


A warning tone will sound when the driver door is opened, the ignition is in ACC/ACCESSORY or LOCK/OFF and the key is in the ignition.


2-21


Retained Accessory Power (RAP) These vehicle accessories can be used for up to 20 minutes after the engine is turned off: (cid:129) Audio System (cid:129) Power Windows (cid:129) Overhead Console (cid:129) Sunroof (if equipped) These features will work when the key is in ON/RUN or ACC/ACCESSORY. Once the key is turned from ON/RUN to LOCK/OFF, these features continue to work for up to 20 minutes, or until a door is opened.


Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart the engine when the vehicle is already moving, use N (Neutral) only. Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the transmission. Shift to P (Park) only when the vehicle is stopped.


Starting Procedure 1. With your foot off the accelerator pedal, turn the


ignition to START. When the engine starts, let go of the key. The idle speed will slow down as the engine warms. Do not race the engine immediately after starting it. Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts. The vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. If the engine does not start and the key is held in START, cranking will be stopped after 15 seconds to prevent cranking motor damage. To prevent gear damage, this system also prevents cranking if the engine is already running. Engine cranking can be stopped by turning the ignition switch to the ACC/ ACCESSORY or LOCK/OFF position.


Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down.


2-22


2. If the engine does not start after 5-10 seconds,


especially in very cold weather (below 0°F or −18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator. If the vehicle starts briefly but then stops again, repeat these steps. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts.


Notice: The engine is designed to work with the electronics in the vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer/retailer. If you do not, the engine might not perform properly. Any resulting damage would not be covered by the vehicle warranty.


Adjustable Throttle and Brake Pedal If the vehicle has this feature, you can change the position of the throttle and brake pedals. The vehicle must be in P (Park) for this feature to operate.


The switch used to adjust the pedals is located on the steering column.


Press the switch forward or backward to move the pedals closer or farther away from you.


2-23


Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F (−18°C). Vehicles with an engine coolant heater should be plugged in at least four hours before starting the vehicle. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above 0°F (−18°C). To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The


cord is located on the driver side of the engine compartment next to the battery box facing the engine.


3. Plug it into a normal, grounded 110-Volt AC outlet.


{ CAUTION:


Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps.


4. Before starting the engine, be sure to unplug and


store the cord as it was before to keep it away from moving engine parts and prevent damage.


The length of time the heater should remain plugged in depends on several factors. Ask a dealer/retailer in the area where you will be parking the vehicle for the best advice on this.


2-24


Active Fuel Management™ The vehicle’s V8 engine may have Active Fuel Management™. This system allows the engine to operate on either all or half of its cylinders, depending on driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing the vehicle to achieve better fuel economy. When greater power is required, such as accelerating from a stop, passing, or merging onto a freeway, the system will maintain full-cylinder operation.


Automatic Transmission Operation


There are several different positions for the gear shift lever.


2-25


P (Park): This position locks the rear wheels. It is the best position to use when you start the engine because the vehicle cannot move easily.


{ CAUTION:


{ CAUTION:


It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). See Shifting Into Park on page 2-34. If you are pulling a trailer, see Towing a Trailer on page 4-46.


If you have four-wheel drive, the vehicle will be free to roll — even if the shift lever is in P (Park) — if the transfer case is in Neutral. So, be sure the transfer case is in a drive gear — not in Neutral. See Four-Wheel Drive on page 2-28. See Shifting Into Park on page 2-34.


Make sure the shift lever is fully in P (Park) before starting the engine. The vehicle has an automatic transmission shift lock control system. You have to fully apply the brake pedal, then press the shift lever button before you can shift from P (Park) when the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 2-36.


2-26


R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped. To rock the vehicle back and forth to get out of snow, ice, or sand without damaging the transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-30.


N (Neutral): In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only.


{ CAUTION:


Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, the vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while the engine is running at high speed.


Notice: Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle. D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: (cid:129) Going less than about 35 mph (55 km/h), push the


accelerator pedal about halfway down.


(cid:129) Going about 35 mph (55 km/h) or more, push the


accelerator all the way down. The vehicle will shift down to the next gear and have more power.


Downshifting the transmission in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 4-12. D (Drive) can be used when towing a trailer, carrying a heavy load, driving on steep hills, or for off-road driving. You may want to shift the transmission to 3 (Third) or, if necessary, a lower gear selection if the transmission shifts too often. 3 (Third): This position is also used for normal driving. It reduces vehicle speed more than D (Drive) without using the brakes. You might choose 3 (Third) instead of D (Drive) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill.


2-27


To shift to the 3 (Third) position, you must first press the large button on the shift handle. While the button is pressed, move the shifter in the 3 (Third) position.


2 (Second): This position reduces vehicle speed even more than 3 (Third) without using the brakes. You can use 2 (Second) on hills. It can help you control vehicle speed as you go down steep mountain roads, as you use your brakes off and on.


To shift to the 2 (Second) position, you must first press the large button on the shift handle. While the button is pressed, move the shifter in the 2 (Second) position. You can also use 2 (Second) for starting the vehicle from a stop on slippery road surfaces.


1 (First): This position reduces vehicle speed even more than 2 (Second) without using the brakes. You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in 1 (First) while the vehicle is moving forward, the transmission will not shift into first gear until the vehicle is going slowly enough.


To shift to the 1 (First) position, you must first press the large button on the shift handle. While the button is pressed, move the shifter in the 1 (First) position.


Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. Four-Wheel Drive If the vehicle has four-wheel drive, the engine’s driving power can be sent to all four wheels for extra traction. Read the following before using four-wheel drive, to become familiar with its operation. You should use Two-Wheel High for most normal driving conditions. Notice: Driving on clean, dry pavement in Four-Wheel-Drive High or Four-Wheel-Drive Low for an extended period of time may cause premature wear on your vehicle’s powertrain. Do not drive on clean, dry pavement in Four-Wheel-Drive High or Four-Wheel-Drive Low for extended periods of time. Notice: transfer case in AUTO or Four-Wheel Drive, you could shorten the life of the transfer case or the Four-Wheel Drive system. The selector switch should be left in Two-Wheel Drive High mode. Only use AUTO and Four-Wheel Drive when you need extra traction such as in wet or slippery road conditions.


If you continually drive your vehicle with the


2-28


Automatic Transfer Case If the vehicle has four-wheel drive, the transfer case knob is located to the right of the steering wheel on the instrument panel.


Use this knob to shift into and out of four-wheel drive.


AUTO (Automatic Four-Wheel Drive): This setting is ideal for use when road conditions are variable. When driving the vehicle in automatic four-wheel drive, the front axle is engaged, but the vehicle’s power is sent to the rear wheels. When the vehicle senses a loss of traction, the system will automatically engage four-wheel drive. Driving in this mode results in slightly lower fuel economy than Two-Wheel High. 4 m (Four-Wheel High): This setting should be used when you need extra traction, such as on snowy or icy roads or in most off-road situations. This setting also engages the front axle to help drive the vehicle.


2 m (Two-Wheel High): This setting is for driving in most street and highway situations. The front axle is not engaged in two-wheel drive. This provides the best fuel economy.


2-29


4 n (Four-Wheel Low): This setting also engages the front axle and delivers extra torque. It sends maximum power to all four wheels. You might choose this setting if you are driving off-road in deep sand, deep mud, and climbing or descending steep hills.


{ CAUTION:


Shifting the transfer case to Neutral can cause the vehicle to roll even if the transmission is in P (Park). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in Neutral. See Parking Brake on page 2-33.


Neutral: Shift the vehicle’s transfer case to Neutral only when towing the vehicle. See Recreational Vehicle Towing on page 4-38 for more information.


An indicator light in the knob will show you which position the transfer case is in. The indicator lights will come on briefly when you turn on the ignition and one will stay on. If the lights do not come on, you should take the vehicle to your dealer/retailer for service. An indicator light will flash while shifting the transfer case. It will stay on when the shift is complete. If the transfer case cannot make a requested shift, it will return to the last chosen setting. If the service Four-Wheel Drive Warning Light on the instrument panel cluster stays on, you should take the vehicle to your dealer/retailer for service. See Service Four-Wheel Drive Warning Light on page 3-44
for further information. Shifting Into Four-Wheel High or Automatic Four-Wheel Drive Turn the knob to Four-Wheel High or Automatic Four-Wheel Drive. This can be done at any speed unless you are shifting out of Four-Wheel Low. The indicator light will flash while shifting. It will remain on when the shift is complete.


2-30


Shifting Into Two-Wheel High Turn the knob to Two-Wheel High. This can be done at any speed unless you are shifting out of Four-Wheel Low. Shifting Into Four-Wheel Low To shift to Four-Wheel Low, the vehicle’s engine must be running and the vehicle must be stopped or moving less than 2 mph (3.2 km/h) with the transmission in N (Neutral). The preferred method for shifting into Four-Wheel Low is to have your vehicle moving 1 or 2 mph (1.6 to 3.2 km/h). Turn the knob to Four-Wheel Low. You must wait for the Four-Wheel Low indicator light to stop flashing and stay on before shifting the transmission into gear. If you turn the knob to Four-Wheel Low when the vehicle is in gear and/or moving, the Four-Wheel Low indicator light will flash for 30 seconds and not complete the shift unless the vehicle is moving less than 2 mph (3.2 km/h) and the transmission is in N (Neutral). After 30 seconds, the transfer case will return to the setting last chosen.


Shifting Out of Four-Wheel Low To shift from Four-Wheel Low to Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High, the vehicle must be stopped or moving less than 2 mph (3.2 km/h) with the transmission in N (Neutral) and the engine running. The preferred method for shifting out of Four-Wheel Low is to have your vehicle moving 1 or 2 mph (1.6 to 3.2 km/h). Turn the knob to Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High. You must wait for the Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High indicator light to stop flashing and stay off before shifting your transmission into gear. If the knob is turned to Four Wheel-High, Auto Four-Wheel Drive, or Two-Wheel High when the vehicle is in gear and/or moving, the Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High indicator light will flash for 30 seconds. It will not complete the shift unless the vehicle is moving less than 2 mph (3.2 km/h) with the transmission in N (Neutral).


2-31


Shifting Out of Neutral To shift the transfer case out of Neutral, do the following: 1. Set the parking brake and apply the regular brake


pedal.


2. Turn the ignition to ON/RUN with the engine off. 3. Put the transmission in N (Neutral). 4. Turn the transfer case knob to the desired position


(Two-Wheel High, Four-Wheel High, or Auto Four-Wheel Drive).


5. After the transfer case has shifted out of Neutral,


the indicator light will go out.


6. Release the parking brake. 7. Start the engine and shift the transmission to the


desired position.


Shifting into Neutral Before shifting the transfer case to Neutral, first make sure the vehicle is parked so that it will not roll.


1. Set the parking brake. 2. Start the vehicle. 3. Put the transmission in N (Neutral). 4. Shift the transfer case to Two-Wheel High. 5. Turn the transfer case knob all of the way past


Four-Wheel Low and hold it there for a minimum of 10 seconds. The Neutral indicator light will come on.


6. With the engine running, shift the transmission to


R (Reverse) for one second, then shift the transmission to D (Drive) for one second, to ensure that the transfer case is in Neutral.


7. Turn the engine off, by turning the key to


ACC/ACCESSORY.


8. Place the transmission shift lever in P (Park). 9. Turn the ignition to LOCK/OFF.


2-32


Parking Brake


To set the parking brake, hold the regular brake pedal down with your foot and pull up on the parking brake lever located between the seats.


If the ignition is on, the brake system warning light on the instrument panel cluster will come on. See Brake System Warning Light on page 3-35. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and you must park on a hill, see Towing a Trailer on page 4-46.


To release the parking brake, hold the regular brake pedal down. Pull the parking brake lever up until you can press in the button at the end of the lever. Hold the button in as you move the parking brake lever all the way down.


2-33


To shift into P (Park): 1. Hold the brake pedal down with your foot and set


the parking brake.


2. Move the shift lever into P (Park) by pressing the button on the side of the shift lever and pushing the lever all the way toward the front of the vehicle.


3. Turn the ignition key to OFF/LOCK. 4. Remove the key and take it with you. You know the


vehicle is in P (Park) if the key can be removed from the ignition.


Shifting Into Park


{ CAUTION:


It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow. With four-wheel drive, the vehicle will be free to roll — even if the shift lever is in P (Park) — if your transfer case is in Neutral. So, be sure the transfer case is in a drive gear — not in Neutral. See Four-Wheel Drive on page 2-28. Always put the shift lever fully in P (Park) with the parking brake firmly set. If you are pulling a trailer, see Towing a Trailer on page 4-46.


2-34


Leaving the Vehicle With the Engine Running


{ CAUTION:


It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. If you have four-wheel drive, the vehicle will be free to roll – even if your lever is in P (Park) – if the transfer case is in Neutral. So be sure the transfer case is in a drive gear – not Neutral. See Four-Wheel Drive on page 2-28. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave the vehicle with the engine running unless you have to.


If you have to leave the vehicle with the engine running, be sure the vehicle is in P (Park) and the parking brake is firmly set before you leave it. After you have moved the shift lever into P (Park), hold the regular brake pedal down. Then, see if you can move the shift lever away from P (Park) without first pressing the button on the console shift lever. If you can, it means that the shift lever was not fully locked into P (Park). Torque Lock If you are parking on a hill and you do not shift your transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of P (Park). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into P (Park) properly before you leave the driver seat. To find out how, see Shifting Into Park on page 2-34. When you are ready to drive, move the shift lever out of P (Park) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of P (Park).


2-35


Shifting Out of Park The vehicle has an electronic shift lock release system. The shift lock release is designed to: (cid:129) Prevent ignition key removal unless the shift lever


is in P (Park) with the shift lever button fully released, and


(cid:129) Prevent movement of the shift lever out of P (Park),


unless the ignition is in ON/RUN and the regular brake pedal is applied.


The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-39 for more information. To shift out of P (Park) use the following: 1. Apply the brake pedal. 2. Press the shift lever button. 3. Move the shift lever to the desired position.


If you still are unable to shift out of P (Park): 1. Fully release the shift lever button. 2. Hold the brake pedal down and press the shift lever


button again.


3. Move the shift lever to the desired position. If you still cannot move the shift lever from P (Park), consult your dealer/retailer or a professional towing service.


Parking Over Things That Burn


{ CAUTION:


Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn.


2-36


Engine Exhaust


{ CAUTION:


Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if:


(cid:129) The vehicle idles in areas with poor ventilation


(parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). (cid:129) The exhaust smells or sounds strange or


(cid:129) The exhaust system leaks due to corrosion or


different.


damage.


CAUTION:


(Continued)


CAUTION:


(Continued)


(cid:129) The vehicle’s exhaust system has been


modified, damaged or improperly repaired. (cid:129) There are holes or openings in the vehicle


body from damage or after-market modifications that are not completely sealed. If unusual fumes are detected or if it is suspected that exhaust is coming into the vehicle:


(cid:129) Drive it only with the windows


completely down.


(cid:129) Have the vehicle repaired immediately.


Never park the vehicle with the engine running in an enclosed area such as a garage or a building that has no fresh air ventilation.


2-37


Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know.


{ CAUTION:


Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 2-37.


{ CAUTION:


CAUTION:


(Continued)


vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park).


{ CAUTION:


If the vehicle has four-wheel drive, it will be free to roll — even if the shift lever is in P (Park) — if the transfer case is in N (Neutral). So be sure the transfer case is in a drive gear — not in N (Neutral). See Four-Wheel Drive on page 2-28.


It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The


CAUTION:


(Continued)


Follow the proper steps to be sure the vehicle will not move. See Shifting Into Park on page 2-34. If pulling a trailer, see Towing a Trailer on page 4-46.


2-38


Mirrors


Manual Rearview Mirror Adjust the mirror to see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment lets you adjust the mirror to avoid glare from the lamps behind you. Move the lever to the right for nighttime use and to the left for daytime use. Vehicles with OnStar® have three control buttons located at the bottom of the mirror. See your dealer/retailer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-43 for more information on the services OnStar® provides.


Automatic Dimming Rearview Mirror The vehicle may have an automatic-dimming rearview mirror with a compass and/or temperature display. See Compass on page 2-40 for more information about the compass display. See “Temperature Display” after in this section. Vehicles with OnStar® have three control buttons located at the bottom of the mirror. See your dealer/retailer for more information on the system and


how to subscribe to OnStar®. See OnStar® System on page 2-43 for more information on the services OnStar® provides. O (On/Off): Press to turn the dimming feature on or off.


TEMP (Temperature): Press to turn the temperature display on or off. Automatic Dimming Mirror Operation Automatic dimming reduces the glare of lights from behind the vehicle. The dimming feature comes on and the indicator light illuminates each time the vehicle is started. Temperature Display Press O or depending on the mirror, press TEMP to turn the temperature display on or off. To adjust between Fahrenheit and Celsius: 1. Press and hold O or depending on the mirror,


press TEMP until either a flashing F or C appears. 2. Press O or TEMP again to change the display to


the desired unit of measurement. After approximately four seconds of inactivity, the new unit locks in and the display returns.


2-39


If an abnormal temperature reading is displayed for an extended period of time, please consult your dealer/retailer. Under certain circumstances, a delay in updating the temperature is normal. Passenger Airbag Indicator The vehicle may be equipped with a passenger airbag indicator, on the mirror glass, just above the buttons. If the vehicle has this feature, the mirror displays the word ON, or an airbag symbol in Canada, when the passenger airbag is enabled. For more information, see Passenger Sensing System on page 1-64. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.


Compass Compass Operation There is a compass display in the upper right corner of the mirror. Press O or depending on the mirror, press COMP to turn the compass on or off.


Compass Calibration The compass may need calibration if: (cid:129) After several seconds, the display does not show a compass heading (N for North, for example), there may be a strong magnetic field interfering with the compass. Interference can be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly.


In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, press and hold O or depending on the mirror, press COMP until CAL displays. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Compass Variance The mirror is set to zone eight. If you do not live in zone eight or drive out of the area, the compass variance needs to be changed to the appropriate zone.


2-40


(cid:129) To adjust for compass variance: 1. Find your current location and variance zone


number on the following zone map.


3. Keep pressing O until the desired zone number


displays. Release the button. After several seconds of inactivity, the new zone number locks in and the compass display returns.


4. Calibrate the compass as previously described.


Outside Manual Mirrors Adjust the outside rearview mirrors to see a little of the side of your vehicle, and the area beside your vehicle. Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position.


2. Press and hold O or depending on the mirror, press COMP until a Z and/or a zone number displays. The compass is now in zone mode.


2-41


Outside Power Mirrors Vehicles with outside power mirrors have controls located on the driver door. To adjust the mirrors: 1. Turn the control knob left or right to select the


driver’s or passenger mirror.


2. Move the control knob to the left or right or up or


down to position the mirror to see a little of the outside of the vehicle.


3. After adjusting the position of the mirrors, turn the knob to the center off position so that the mirrors do not move.


If the end of travel position in any direction of the mirror is reached, it will enter a ratcheting mode. This action is harmless. It is a warning that the mirror can go no further. To stop this action, back the mirror up by moving the knob in the opposite direction. Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirrors toward the vehicle. To return the mirrors to their original position, push outward.


Outside Convex Mirror


{ CAUTION:


A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.


The passenger side mirror is convex shaped. A convex mirror’s surface is curved so more can be seen from the driver seat.


Outside Heated Mirrors < (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Climate Control System on page 3-19 or Dual Automatic Climate Control System on page 3-22 for more information.


2-42


OnStar® System


OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If the keys are locked in the vehicle, call OnStar at 1-888-4-ONSTAR to have a signal sent to unlock the doors. OnStar Hands-Free Calling, including 30 trial minutes good for 60 days, is available on most vehicles. OnStar Turn-by-Turn Navigation service, with one trial route, is available on most vehicles. Press the OnStar button to have an OnStar advisor contact Roadside Service.


OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the first prepaid year, contact OnStar to select a monthly or annual subscription payment plan. If a payment plan is not selected, the OnStar system and all services, including airbag notification and emergency services, may be deactivated and no longer available. For more information visit onstar.com (U.S.) or onstar.ca (Canada), or press the OnStar button to speak with an advisor. Not all OnStar services are available on all vehicles. To check if this vehicle is able to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in the glove box or visit onstar.com (U.S.) or onstar.ca (Canada), contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week.


2-43


OnStar Services Available with the Safe & Sound Plan (cid:129) Automatic Notification of Airbag Deployment (cid:129) Advanced Automatic Crash Notification (AACN)


(If equipped) Link to Emergency Services


(cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar Vehicle Diagnostic Email (cid:129) GM Goodwrench On Demand Diagnostics (cid:129) OnStar Hands-Free Calling with 30 trial minutes (cid:129) OnStar Virtual Advisor (U.S. Only) OnStar Services Included with Directions & Connections Plan (cid:129) All Safe and Sound Plan Services (cid:129) OnStar Turn-by-Turn Navigation (If equipped) or


Driving Directions - Advisor delivered


(cid:129) RideAssist


Information and Convenience Services


2-44


OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days. Hands-Free Calling can also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To find out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit onstar.com or onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Turn-by-Turn Navigation Vehicles with the OnStar Turn-by-Turn Navigation system can provide voice-guided driving directions. Press the OnStar button to have an OnStar advisor locate a business or address and download driving directions to the vehicle. Voice-guided directions to the desired destination will play through the audio system speakers. See the OnStar Owner’s Guide for more information.


(cid:129) (cid:129) OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traffic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics. See the OnStar Owner’s Guide for more information. This feature is only available in the continental U.S. OnStar Steering Wheel Controls This vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-110 for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information.


How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy. This information usually includes the vehicle’s GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). When the Virtual Advisor feature of OnStar Hands-Free Calling is used, the vehicle also sends OnStar the vehicle’s GPS location so they can provide services where it is located. OnStar service cannot work unless the vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless the vehicle is in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times.


2-45


Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place. Some examples are damage to important parts of the vehicle in a crash, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard. If the light next to the OnStar buttons is red, the system may not be functioning properly. Press the OnStar button and request a vehicle diagnostic. If the light appears clear (no light is appearing), your OnStar subscription has expired and all services have been deactivated. Press the OnStar button to confirm that the OnStar equipment is active.


Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received,


including interference that may cause undesired operation.


This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received,


including interference that may cause undesired operation of the device.


Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.


2-46


Universal Home Remote System Operation (With One Triangular LED)


If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982.


Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate that is being programmed. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal.


2-47


Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons.


2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit).


3. At the same time, press and hold both the Universal


Home Remote button to be used to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require substitution of Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.


Programming the Universal Home Remote System For questions or help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated. To program up to three devices:


1. From inside the vehicle, press and hold down the


two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to flash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons.


2-48


4. The indicator light on the Universal Home Remote


will flash slowly at first and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons.


5. Press and hold the newly-trained Universal Home


Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and the garage door should move when the Universal Home Remote button is pressed and released. There is no need to continue programming Steps 6 through 8. If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6 through 8. It may be helpful to have another person assist with the remaining steps.


6. After Steps 1 through 5 have been completed,


locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer.


7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8.


2-49


If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted.


8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door.


To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming the Universal Home Remote System.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.


2-50


Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Home Remote device:


1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds.


2. Release both buttons.


Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-6. Storage Areas


Glove Box Lift the glove box handle up to open it. Use the key to lock and unlock the glove box.


Overhead Console Your vehicle may have this feature. The overhead console may include reading lamps, a Universal Home Remote and a sunroof switch. See Sunroof on page 2-55 and Universal Home Remote System on page 2-46 for more information.


2-51


Center Console Storage Pull the front lever on the center console while lifting the top to open it. The console has cupholders on the front and rear of the storage compartment. The console may also contain: (cid:129) Rear Seat Audio Controls (cid:129) Rear Seat Accessory Power Outlets (cid:129) Rear Climate Control To open the center armrest compartment, lift the cover by pulling up on the latch handle located under the front edge of the armrest.


Luggage Carrier


{ CAUTION:


If something is carried on top of the vehicle that is longer or wider than the luggage carrier — like paneling, plywood, or a mattress— the wind can catch it while the vehicle is being driven. This can cause a driver to lose control. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle. Items may be carried inside. Never carry something longer or wider than the luggage carrier on top of the vehicle.


If your vehicle has a luggage carrier, it will allow you to load things on top of your vehicle. The luggage carrier has side rails attached to the roof, places to use for tying things down and may have sliding crossrails. These let you load some other things on top of your vehicle, as long as they are not wider or longer than the luggage carrier.


2-52


To slide the crossrails to where you want them, pull up on the lever on each side of the crossrail. This releases the crossrail and allows you to slide it. When the crossrail is where you want it, press down on the levers to lock it into place. Notice: Loading cargo on the luggage carrier that weighs more than 220 lbs (100 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading the Vehicle on page 4-31. To prevent damage or loss of cargo as you are driving, check now and then to make sure the luggage carrier is locked and cargo is still securely fastened. When the luggage carrier is not in use, place the crossrails at the following positions for wind noise reduction. Place one crossrail at the rear most point of the vehicle and the other crossrail above the opening of the rear door.


Rear Floor Storage Cover


{ CAUTION:


If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly.


The vehicle has a rear cargo area with a removable storage cover. To remove the rear floor storage cover, do the following: 1. Press the latch release and lift up the latch


handle.


2. Raise the cover slightly to unhook it. 3. Pull the cover towards the rear of the vehicle to


release it from the forward mounting slots.


To reinstall the rear floor storage cover, reverse the previous steps. Make sure the cover is secure by applying slight pressure to the latch until it clicks.


2-53


Convenience Net For vehicles with a convenience net located in the rear, use it to store small loads as far forward as possible. The net should not be used to store heavy loads.


Cargo Cover If your vehicle has a cargo cover, you can use it to cover items in the cargo area of your vehicle. To install the cargo cover: 1. Align the endcap with the pocket in the trim panel


located behind the rear seat.


2. Squeeze the opposite endcap, align it with the pocket located on the opposite side of the trim panel and release.


3. Grasp the handle and unroll the cover. 4. Latch the posts into the sockets on the inside of the


vehicle to secure it.


To remove the cargo cover, do the following: 1. Release the cover from the latch posts and carefully


roll it back up.


2. Squeeze one endcap and remove it from the


pocket in the trim panel.


3. Remove the cargo cover from the other endcap so


that you can remove the shade from the vehicle.


{ CAUTION:


An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver. Someone could be injured. If the cover is removed, always store it in the proper storage location. When it is replaced, always be sure that it is securely reattached.


2-54


Cargo Tie Downs Four cargo tie-downs are located in the rear compartment of the vehicle. The tie-downs can be used to secure small loads. Sunroof The vehicle may have a power sliding sunroof. To open or close the sunroof, the ignition must be turned to ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active. See Retained Accessory Power (RAP) on page 2-22.


Press and release the back of the control in the overhead console to open the sunroof. Press the front of the control to close the sunroof.


Once the sunroof is closed, press the forward side of the control to open the sunroof to the vent position. The sunroof has a sunshade which can be pulled forward to block sun rays. If it is in the closed position, it will open when the sunroof opens. Do not keep the sunroof open for long periods of time while the vehicle is not in use. Debris can collect in the tracks, damage the sunroof operation and plug the water draining system.


2-55


✍ NOTES


2-56


Section 3


Instrument Panel


Instrument Panel Overview ...............................3-4
Hazard Warning Flashers ................................3-6
Horn .............................................................3-6
Tilt Wheel .....................................................3-6
Turn Signal/Multifunction Lever .........................3-7
Turn and Lane-Change Signals ........................3-7
Headlamp High/Low-Beam Changer ..................3-8
Flash-to-Pass .................................................3-8
Windshield Wipers ..........................................3-8
Windshield Washer .........................................3-9
Rear Window Wiper/Washer .............................3-9
Headlamp Washer ........................................3-10
Cruise Control ..............................................3-10
Headlamps ..................................................3-13
Headlamps on Reminder ................................3-14
Daytime Running Lamps (DRL) .......................3-14
Automatic Headlamp System ..........................3-14
Fog Lamps ..................................................3-15
Instrument Panel Brightness ...........................3-16
Dome Lamps ...............................................3-16
Dome Lamp Override ....................................3-16
Entry Lighting ...............................................3-16


Exit Lighting .................................................3-17
Reading Lamps ............................................3-17
Electric Power Management ...........................3-17
Battery Run-Down Protection ..........................3-18
Accessory Power Outlet(s) .............................3-18
Ashtray(s) and Cigarette Lighter ......................3-19
Climate Controls ............................................3-19
Dual Climate Control System ..........................3-19
Dual Automatic Climate Control System ...........3-22
Outlet Adjustment .........................................3-26
Rear Climate Control System .........................3-26
Warning Lights, Gages, and Indicators ............3-27
Instrument Panel Cluster ................................3-28
Speedometer and Odometer ...........................3-29
Trip Odometer ..............................................3-29
Tachometer .................................................3-29
Safety Belt Reminders ...................................3-30
Airbag Readiness Light ..................................3-31
Passenger Airbag Status Indicator ...................3-32
Charging System Light ..................................3-33
Voltmeter Gage ............................................3-34


3-1


Section 3


Instrument Panel


Brake System Warning Light ..........................3-35
Antilock Brake System (ABS) Warning Light .....3-36
StabiliTrak® Service Light ...............................3-36
StabiliTrak® Indicator Light .............................3-37
Engine Coolant Temperature Gage ..................3-37
Tire Pressure Light .......................................3-38
Malfunction Indicator Lamp .............................3-38
Oil Pressure Gage ........................................3-42
Change Engine Oil Light ................................3-43
Security Light ...............................................3-43
Cruise Control Light ......................................3-43
Reduced Engine Power Light .........................3-44
Highbeam On Light .......................................3-44

Loading...
x