Download PDF Manual


AAE124788E142442 Driving Aids


The Blind Spot Information System illuminates an amber alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from. When the Blind Spot Information System is alerting on a vehicle and the corresponding turn signal is ON, the Blind Spot Information System alert indicator flashes as an increased warning level. The alert indicator dims when the system detects nighttime darkness. Note: The alert indicator flashes in case of an alert and the turn signal is set to that side at the same time. System Sensor Blockage WARNING


To help avoid injuries, NEVER use the Blind Spot Information System as a replacement for using the interior and exterior mirrors or looking over your shoulder before changing lanes. The Blind Spot Information System is not a replacement for careful driving.


The system uses radar sensors that are located behind the bumper fascia on each side of your vehicle. Any dirt, mud and snow in front of the sensors and/or driving in heavy rain can cause system degradation. Also, other types of obstructions in front of the sensor can cause system degradation. This is referred to as a ‘blocked’ condition. Note: Do not apply bumper stickers and/or repair compound to these areas, this can cause degraded system performance.


142


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E205199 Driving Aids



If the system detects a degraded performance condition, a message warning of a blocked sensor will appear in the information display. Also the BLIS alert indicators will remain ON and BLIS will no longer provide any vehicle warnings. You can clear the information display warning but the alert indicators will remain illuminated. A "blocked" condition can be cleared in two ways: • After the blockage in front of the


sensors is removed or the rainfall/snowfall rate decreases or stops, drive for a few minutes in traffic to allow the sensors to detect passing vehicles. By cycling the ignition from ON to OFF and then back ON.


Note: If your vehicle has a tow bar with a factory equipped trailer tow module and it is towing a trailer, the sensors will automatically turn the Blind Spot Information System off. If your vehicle has a tow bar but no factory equipped trailer tow module, it is recommended to turn the Blind Spot Information System off manually. Operating the Blind Spot Information System with a trailer attached will cause poor system performance. System Errors If the system senses a problem with the left or right sensor, the telltale will illuminate and a message will appear in the information display. See Information Messages (page 88).


Switching the System Off and On You can temporarily switch the Blind Spot Information System off in the information display. See General Information (page 85). When the Blind Spot Information System switches off, you will not receive alerts and the information display shows a system off message. The telltale in the cluster also illuminates. When you switch the Blind Spot Information System on or off, the alert indicators flash twice. Note: The Blind Spot Information System remembers the last selected on or off setting. You can also have the Blind Spot Information System switched off permanently at an authorized dealer. Once switched off permanently, the system can only be switched back on at an authorized dealer. CROSS TRAFFIC ALERT


WARNING


To help avoid personal injury, NEVER use the Cross Traffic Alert system as a replacement for using the interior and exterior mirrors and looking over your shoulder before backing out of a parking space. Cross Traffic Alert is not a replacement for careful driving.


Cross Traffic Alert is designed to warn you of vehicles approaching from the sides when the transmission is in reverse (R). Using the System Cross Traffic Alert turns on when you start the engine and you shift into reverse (R). Once shifted out of reverse (R), Cross Traffic Alert turns off. Note: Cross Traffic Alert only functions while your transmission is in reverse (R).


143


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Driving Aids


Cross Traffic Alert is designed to detect vehicles that approach with a speed up to 37 mph (60 km/h). Coverage decreases when the sensors are partially, mostly or


fully obstructed. Reversing slowly helps increase the coverage area and effectiveness.


In this first example, the left sensor is only partially obstructed; zone coverage to the right is nearly maximized.


144


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E142440E142441 Driving Aids


Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited. System Lights, Messages and Audible Alerts


The Cross Traffic Alert illuminates an amber alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from. Cross Traffic Alert also sounds an audible alert and a message appears in the information display indicating a vehicle is coming from the right or left. Cross Traffic Alert works with the reverse sensing system that sounds its own series of tones. See Rear Parking Aid (page 135).


The system uses radar sensors that are located behind the bumper fascia on each side of your vehicle. Do not allow mud, snow or bumper stickers to obstruct these areas, this can cause degraded system performance. See Blind Spot Information System (page 141). If the Blind Spot Information System is blocked, Cross Traffic Alert is also blocked. A corresponding message appears in the information display as soon as you shift the transmission into reverse (R). System Limitations Cross Traffic Alert has its limitations; situations such as severe weather conditions or debris build-up on the sensor area may limit vehicle detection.


145


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E142442E205199 Driving Aids


The following are other situations that may limit the Cross Traffic Alert performance: • Adjacently parked vehicles or objects


obstructing the sensors.


• Approaching vehicles passing at


speeds greater than 37 mph (60 km/h).


• Driving in reverse faster than 7 mph


(12 km/h). Backing out of an angled parking spot.


• False Alerts Note: If your vehicle has a tow bar with a factory equipped trailer tow module and it is towing a trailer, the sensors will automatically turn the Cross Traffic Alert off. If your vehicle has a tow bar but no factory equipped trailer tow module, it is recommended to turn the Cross Traffic Alert off manually. Operating Cross Traffic Alert with a trailer attached will cause poor Cross Traffic Alert performance. There may be certain instances when there is a false alert by the Cross Traffic Alert system that illuminates the alert indicator with no vehicle in the coverage zone. Some amount of false alerts are normal; they are temporary and self-correct. System Errors If Cross Traffic Alert senses a problem with the left or right sensor a message will appear in the information display. See Information Messages (page 88). Switching the System Off and On You can temporarily switch Cross Traffic Alert off in the information display. See General Information (page 85). When you switch Cross Traffic Alert off, you will not receive alerts and the information display will display a system off message.


Note: The Cross Traffic Alert switches on whenever the ignition is switched on and ready to provide appropriate alerts when the transmission is in reverse (R). Cross Traffic Alert will not remember the last selected on or off setting. You can also have Cross Traffic Alert switched off permanently at an authorized dealer. Once switched off permanently, the system can only be switched back on at an authorized dealer. STEERING Electric Power Steering WARNINGS


The electric power steering system has diagnostic checks that continuously monitor the system. If a fault is detected, a message displays in the information display. Stop your vehicle as soon as it is safe to do so. Switch the ignition off. After at least 10 seconds, switch the ignition on and watch the information display for a steering system warning message. If a steering system warning message returns, have the system checked by an authorized dealer.


If the system detects an error, you may not feel a difference in the steering, however a serious condition may exist. Obtain immediate service from an authorized dealer, failure to do so may result in loss of steering control.


Your vehicle has an electric power steering system. There is no fluid reservoir. No maintenance is required. If your vehicle loses electrical power while you are driving, electric power steering assistance is lost. The steering system still operates and you can steer your vehicle manually. Manually steering your vehicle requires more effort.


146


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Driving Aids


Extreme continuous steering may increase the effort required for you to steer your vehicle. This increased effort prevents overheating and permanent damage to the steering system. You do not lose the ability to steer your vehicle manually. Typical steering and driving maneuvers allow the system to cool and return to normal operation. Steering Tips If the steering wanders or pulls, check for: • Correct tire pressures. • Uneven tire wear. •


Loose or worn suspension components. Loose or worn steering components. Improper vehicle alignment.


• • Note: A high crown in the road or high crosswinds may also make the steering seem to wander or pull. Adaptive Learning The electronic power steering system adaptive learning helps correct road irregularities and improves overall handling and steering feel. It communicates with the brake system to help operate advanced stability control and accident avoidance systems. Additionally, whenever the battery is disconnected or a new battery installed, you must drive your vehicle a short distance before the system relearns the strategy and reactivates all systems.


147


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Load Carrying


LUGGAGE ANCHOR POINTS


REAR UNDER FLOOR STORAGE Passenger Compartment Floor (If Equipped)


Variant


Transit Courier Transit Connect


Maximum Load


Value


785 lb (357 kg) 900 lb (408 kg)


The under floor storage compartment is located behind the front passenger seat. Adjustable Load Floor (If Equipped)


148


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E167350E78097E142446 Load Carrying


1. Push the ends of the upper bar toward


each other and insert them into the retainers in the roof. Push the bar forward into the narrow section of the retainers.


Vehicles with the standard size spare tire can adjust the load floor to two positions. The front of the load floor can be placed either on (for high position) or below (for low position) the ledges behind the rear seats. The rear of the load floor always sits on the two small shelves located on the liftgate trim. CARGO NETS Installing the Net (If Equipped)


WARNINGS


Always attach and tighten the net to the luggage anchor points and do not put more than 22 lb (10 kg) of cargo


behind the net and above the seat back. Otherwise, the net could fail and cargo could become a projectile, which could cause serious injury.


Do not allow people to ride in the third row seating positions when the cargo net is installed behind the second row. Failure to do so may limit egress from the vehicle in an emergency.


2. Attach the net to the luggage anchor points. See Luggage Anchor Points (page 148).


149


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E1710171122E167370 Load Carrying


Removing the Net


3. Tighten the straps.


1. Release the straps. 2. Remove the net from the luggage


anchor points.


3. Remove the upper bars. ROOF RACKS AND LOAD CARRIERS


WARNINGS


Read and follow the manufacturer’s instructions when you are fitting a roof rack. Failure to take care may


lead to a crash or personal injury.


When loading the roof racks, we recommend you evenly distribute the load, as well as maintain a low


center of gravity. Loaded vehicles, with higher centers of gravity, may handle differently than unloaded vehicles. Take


150


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E167371E167372 Load Carrying


LOAD LIMIT Vehicle Loading - with and without a Trailer This section will guide you in the proper loading of your vehicle, trailer or both, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label: Base Curb Weight - is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment. Vehicle Curb Weight - is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment.


WARNINGS


extra precautions, such as slower speeds and increased stopping distance, when driving a heavily loaded vehicle. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.


For correct roof rack system function, you must place loads directly on crossbars fitted to the roof rack side rails. When using the roof rack system, we recommend you use Ford genuine accessory crossbars designed specifically for your vehicle. Make sure that you securely fasten the load. Check the tightness of the load before driving and at each fuel stop. Note: If you use a roof rack, the fuel consumption of your vehicle will be higher and you may experience different driving characteristics. Note: Never place loads directly on the roof panel. Maximum Load Weights Do not exceed the following maximum roof rack load weights.


Variant


Maximum Load lb


(kg)* 132 (60)


Wagon - short wheel base with panoramic roof panel Wagon - short wheel base with metal roof panel Wagon - long wheel base Van *Evenly distribute the load on the roof rack.


165 (75)


165 (75)


165 (75)


151


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Load Carrying


WARNING


The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.


Example only:


Payload - is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload. The payload listed on the Tire Label is the maximum payload for the vehicle as built by the assembly plant. If you install any aftermarket or authorized-dealer installed equipment on the vehicle, you must subtract the weight of the equipment from the payload listed on the Tire Label in order to determine the new payload.


152


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E143816PAYLOADE210944 Load Carrying


Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver seating position. The total load on each axle must never exceed its Gross Axle Weight Rating. Note: For trailer towing information refer to the RV and Trailer Towing Guide available at an authorized dealer.


Cargo Weight - includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) - is the total weight placed on each axle (front and rear) including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) - is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance


153


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E210945E143817CARGO Load Carrying


GVW (Gross Vehicle Weight) - is the Vehicle Curb Weight, plus cargo, plus passengers. GVWR (Gross Vehicle Weight Rating) - is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). It is shown on the Example only:


Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver seating position. The Gross Vehicle Weight must never exceed the Gross Vehicle Weight Rating.


154


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E143818GVWE198828 Load Carrying


WARNING


Exceeding the Safety Compliance Certification


Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.


GCW (Gross Combined Weight) - is the Gross Vehicle Weight plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) - is the maximum allowable weight of the vehicle and the loaded trailer, including all cargo and passengers, that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at Gross Vehicle Weight Rating, not at Gross Combined Weight Rating.) Separate functional brakes should be used for safe control of towed vehicles and for trailers where the Gross Combined Weight of the


towing vehicle plus the trailer exceed the Gross Vehicle Weight Rating of the towing vehicle. The Gross Combined Weight must never exceed the Gross Combined Weight Rating. Maximum Loaded Trailer Weight - is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with mandatory options, driver and front passenger weight (150 pounds [68 kilograms] each), no cargo weight (internal or external) and a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer). Consult an authorized dealer (or the RV and Trailer Towing Guide available at an authorized dealer) for more detailed information.


155


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E143819GCWGVW Load Carrying


Tongue Load or Fifth Wheel King Pin Weight - refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5000 pound (2268 kilogram) conventional trailer, multiply 5000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 pounds (227 to 340 kilograms). For an 11500 pound (5216 kilogram) fifth wheel trailer, multiply by 0.15 and 0.25 to obtain a proper king pin load range of 1725 to 2875 pounds (782 to 1304 kilograms). WARNINGS


Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.


Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GAWR limitations.


Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury.


Steps for determining the correct load limit:


1. Locate the statement "The


combined weight of occupants and cargo should never exceed XXX kg or XXX lb." on your vehicle’s placard.


2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.


3. Subtract the combined weight


of the driver and passengers from XXX kg or XXX lb.


4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400-750 (5 x 150) = 650 lb.).


5. Determine the combined


weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.


6.


The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity:


156


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Load Carrying


be: 635 kilograms - (2 x 99
kilograms) - (12 x 45 kilograms) = 635 - 198 - 540 = -103 kilograms. You will need to reduce the load weight by at least 240 pounds (104 kilograms). If you remove three 100-pound (45-kilogram) cement bags, then the load calculation would be: 1400 - (2 x 220) - (9 x 100) = 1400 - 440 - 900 = 60 pounds. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kilograms - (2 x 99
kilograms) - (9 x 45 kilograms) = 635 - 198 - 405 = 32 kilograms. The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver seating position.


*Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You decide to go golfing. Is there enough load capacity to carry you, four of your friends and all the golf bags? You and four friends average 220
pounds (99 kilograms) each and the golf bags weigh approximately 30 pounds (13.5 kilograms) each. The calculation would be: 1400 - (5 x 220) - (5 x 30) = 1400 - 1100
- 150 = 150 pounds. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635
kilograms - (5 x 99 kilograms) - (5 x 13.5 kilograms) = 635 - 495 - 67.5 = 72.5 kilograms. *Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past two years. Measuring the inside of the vehicle with the rear seat folded down, you have room for twelve 100-pound (45-kilogram) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 pounds (99 kilograms), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440
- 1200 = - 240 pounds. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would


157


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Load Carrying


Special Loading Instructions for Owners of Pick-up Trucks and Utility-type Vehicles


WARNING


Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.


Your vehicle can haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling cargo and people may raise the center of gravity of the vehicle.


158


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Towing


TOWING A TRAILER WARNINGS


Do not exceed the GVWR or the GAWR specified on the


certification label.


Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.


The electrical system on your vehicle may have fuses or relays related to the towing equipment. See Fuses (page 181). The load capacity of your vehicle is designated by weight not volume. You will not necessarily be able to use all available space when loading your vehicle or trailer. Towing a trailer places extra load on the engine, transmission, axle, brakes, tires and suspension. Inspect these components before, during and after towing.


Load Placement To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest


to the trailer floor.


• Load the heaviest items


centered between the left and right side trailer tires.


• Load the heaviest items above the trailer axles or just slightly forward toward the trailer tongue. Do not allow the final trailer tongue weight to go above 15% or below 10% of the loaded trailer weight.


• Select a tow bar with the


correct rise or drop. When both the loaded vehicle and trailer are connected, the trailer frame should be level, or slightly angled down toward your vehicle, when viewed from the side. Note: A slight vibration or shudder may be present when you start to drive away due to increased payload weight. Information on correct trailer loading and preparing your vehicle is available in the load carrying section. See Load Limit (page 151). Further information is available in the RV and Trailer Towing Guide. See an authorized dealer.


159


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Towing


Note: Make sure you take the trailer frontal area into consideration, do not exceed 20
feet² (1.86 meters²). Towing a trailer that exceeds this frontal area will reduce the performance and fuel economy of your vehicle when towing. Select a trailer that has a rounded front and an aerodynamic design. Note: For high altitude operation, reduce the gross combined weight by 2% per 1000 feet (300 meters) starting at the 1000 foot (300
meter) elevation point. Note: Certain states require electric trailer brakes for trailers over a specified weight. Be sure to check state regulations for this specified weight. The maximum loaded trailer weights listed may be limited to this specified weight, as the vehicle’s electrical system may not include the wiring connector needed to activate electric trailer brakes.


TRAILER SWAY CONTROL If the trailer begins to sway the stability control warning lamp flashes in the information display. The system applies the brakes to the individual wheels and reduces engine torque to aid vehicle stability. Stop your vehicle as soon as it is safe to do so. Check the vertical weight on the tow ball and trailer load distribution. See Capacities and Specifications (page 249). See Load Carrying (page 148). Note: This feature does not prevent trailer sway, but reduces it once it begins. Note: This feature cannot stop all trailers from swaying. Note: In some cases, if your vehicle speed is too high, the system may turn on multiple times, gradually reducing your vehicle speed. RECOMMENDED TOWING WEIGHTS Your vehicle may tow a trailer. The maximum loaded trailer weight must be less than or equal to the maximum loaded trailer weight listed for your vehicle configuration on the following chart. Note: Do not exceed the maximum loaded trailer weight for your vehicle configuration listed in the chart below.


160


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Towing


3. This equals the maximum


loaded trailer weight for this combination.


Note: The trailer tongue load is an integral part of the payload of the vehicle. Reduce the total payload by the final trailer tongue weight. Note: Consult an authorized dealer to determine the maximum trailer weight allowed for your vehicle if you are not sure.


Calculating the Maximum Loaded Trailer Weight 1. Start with the gross combined weight rating for your vehicle. See the following chart.


2. Subtract all of the following


that apply to your vehicle: • Vehicle curb weight • Hitch hardware weight


including: draw bar, tow ball, locks and weight distributing hardware


• Driver and any passengers


weight


weight


• Payload, cargo or luggage


• Aftermarket equipment


weight. Powertrain


Maximum GCWR - lb


(kg)


Maximum Loaded Trailer Weight - lb


(kg) *


1.6L SWB van 1.6L LWB van 1.6L SWB wagon 2.5L SWB van 2.5L LWB Van 2.5L SWB Wagon 2.5L LWB Wagon *Calculated with SAE J2807 method.


5,820 (2,640) 5,919 (2,685) 5,981 (2,713) 5,840 (2,649) 5,959 (2,703) 6,021 (2,731) 6,325 (2,869)


2,000 (907) 2,000 (907) 2,000 (907) 2,000 (907) 2,000 (907) 2,000 (907) 2,000 (907)


161


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Towing


ESSENTIAL TOWING CHECKS Follow these guidelines for safe towing: • Do not tow a trailer until you drive your


vehicle at least 1000 miles (1600
kilometers).


• Consult your local motor vehicle laws


for towing a trailer. See the instructions included with towing accessories for the correct installation and adjustment specifications. Service your vehicle more frequently if you tow a trailer. See Scheduled Maintenance (page 386). If you use a rental trailer, follow the rental agency's instructions.





Another chapter of this manual contains load specification terms found on the tire label and Safety Compliance label and instructions on calculating your vehicle's load. See Load Limit (page 151). Remember to account for the trailer tongue weight as part of your vehicle load when calculating the total vehicle weight. Trailer Towing Connector


When attaching the trailer wiring connector to your vehicle, only use a proper fitting connector that works with the vehicle and trailer functions.


162


Note: You cannot use a seven-pin trailer wiring connector for your vehicle and the trailer lighting equipment.


Function


Left turn signal and stop lamp Ground (-) Right turn signal and stop lamp Running lights


Color Yellow White Green


Brown Hitches


WARNING


Do not tow a trailer that exceeds the maximum limit of the towing equipment. This could result in


vehicle structural damage, loss of vehicle control and personal injury.


Do not use a hitch that either clamps onto the bumper or attaches to the axle. Distribute the trailer load so that between 10% and 15% of the total trailer weight is on the tongue. The hitch rating on the trailer hitch label is the maximum possible trailer rating. To find the maximum trailer weight allowed for your vehicle See Recommended Towing Weights (page 160). Further information is available in the RV and Trailer Towing Guide. See an authorized dealer. Safety Chains Always connect the safety chains to the hook retainers of your vehicle hitch. To connect the safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground.


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E168683 Towing


Before Towing a Trailer Practice turning, stopping and backing up to get the feel of your vehicle-trailer combination before starting on a trip. When turning, make wider turns so the trailer wheels clear curbs and other obstacles. When Towing a Trailer • Do not drive faster than 70 mph (113


km/h) during the first 500 miles (800
kilometers).


• Do not make full-throttle starts. • Check the trailer hitch, electrical


connections and trailer wheel lug nuts thoroughly after you have traveled 50
miles (80 kilometers).


• When stopped in congested or heavy traffic during hot weather, place the transmission selector lever in position P to aid engine and transmission cooling and to help A/C performance. Turn off the speed control with heavy loads or in hilly terrain. The speed control may turn off automatically when you are towing on long, steep grades.



• When driving down a long or steep hill,


if your vehicle is fitted with a SelectShift Automatic® Transmission, use a low gear, See Automatic Transmission (page 126). Do not apply the brakes continuously, as they may overheat and become less effective. If the transmission is fitted with Grade Assist or a Towing feature, use this feature when towing. This provides engine braking and helps eliminate excessive transmission shifting for optimum fuel economy and transmission cooling.


Note: Never attach safety chains to the bumper. Trailer Brakes


WARNING


Do not connect a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances of having a crash greatly increase.


Electric brakes and manual, automatic or surge-type trailer brakes are safe if you install them correctly and adjust them to the manufacturer's specifications. The trailer brakes must meet local and federal regulations. The rating for the tow vehicle's braking system operation is at the gross vehicle weight rating, not the gross combined weight rating. Separate functioning brake systems are required for safe control of towed vehicles and trailers weighing more than 1500
pounds (680 kilograms) when loaded. Trailer Lamps


WARNING


Never connect any trailer lamp wiring to the vehicle's tail lamp wiring; this may damage the electrical system


resulting in fire. Contact an authorized dealer as soon as possible for assistance in correct trailer tow wiring installation. Additional electrical equipment may be required.



Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard warning flashers are working.


163


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Towing



If your vehicle has AdvanceTrac with RSC and a heavily loaded trailer is on tow, the system may turn on while taking corners. This is normal. Taking corners at slower speeds can reduce this tendency.


• Allow more distance for stopping with a trailer attached. Anticipate stops and brake gradually.


• Avoid parking on a grade. However, if


you must park on a grade: •


Turn the steering wheel to point your vehicle tires away from traffic flow. Set the vehicle parking brake.


• • Place the transmission selector


lever in position P.


• Place wheel chocks in front and


back of the trailer wheels. (Chocks not included with vehicle.)


Launching or Retrieving a Boat or Personal Watercraft Note: Disconnect the trailer wiring connector before the trailer enters the water. Note: Reconnect the trailer wiring connector after the trailer is removed from the water. When backing down a ramp during boat launching or retrieval: • Do not allow the static water level to rise above the bottom edge of the rear bumper.


• Do not allow waves to break higher


than 6 inches (15 centimeters) above the bottom edge of the rear bumper. Note: Exceeding these limits may allow water to enter your vehicle or its components, affecting driveability, emissions and reliability. The vehicle warranty may not cover component damage caused by water entry.


Replace the rear axle lubricant anytime the rear axle has been submerged in water. Water may have contaminated the rear axle lubricant, which is not normally checked or changed unless a leak is suspected or other axle repair is required. TOWING POINTS (If Equipped)


WARNING


The screw-in recovery hook has a left-hand thread. Turn it counterclockwise to install it. Make


sure that the recovery hook is fully tightened. Failure to do so could result in the recovery hook becoming loose.


Due to requirements in some countries, your vehicle may have a recovery hook. Recovery Hook Storage


If your vehicle has a recovery hook, it will be in the luggage compartment on the left-hand side. If your vehicle does not have a recovery hook, you can purchase one from an authorized dealer.


164


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E165020 Towing


Front Recovery Hook


TRANSPORTING THE VEHICLE


Remove the cover and install the recovery hook. Rear Recovery Hook


Remove the cover and install the recovery hook. Note: If your vehicle has a tow bar, you cannot install the recovery hook. Use the tow bar to tow other vehicles.


If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If the vehicle is towed incorrectly, or by any other means, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.


165


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E165018E165019E143886 Towing


You can tow your vehicle from the front with wheel lift equipment to raise the front wheels off the ground. We recommend that you place the rear wheels on a dolly to prevent damage to the rear of your vehicle. You can tow your vehicle from the rear with wheel lift equipment. Note: You must place the front wheels on a dolly to prevent damage to the transmission. TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing


WARNING


If your vehicle has a steering wheel lock make sure the ignition is in the accessory or on position when being


towed.


If your vehicle is disabled and you have no access to a tow dolly, car-hauling trailer or a flatbed transport vehicle, it can only be flat-towed with all wheels on the ground under the following conditions: •


Your vehicle is facing forward so that it is towed in a forward direction. The transmission selector lever is placed in position N. If the transmission gear shift lever cannot be moved to position N, it may need to be overridden. See Automatic Transmission (page 126).



Tow ropes or rigid towing bars must be placed on the same side. For example; right hand rear towing point to right hand front towing point. You must use a tow rope or rigid towing bar that is of the correct strength for the weight of the towing vehicle and the vehicle that is being towed. Note: Using a rigid towing bar is the safest way to tow a vehicle. The weight of the vehicle that is being towed must not exceed the weight of the towing vehicle. Recreational Vehicle Towing Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. See Climate Control (page 95). Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. We designed these guidelines to prevent damage to your transmission. Front-wheel drive vehicles CANNOT be flat-towed (all wheels on the ground), as transmission damage may occur. You can tow your vehicle with the front wheels off the ground by using a tow dolly. If you are using a tow dolly, follow the instructions specified by the equipment provider.


• Maximum speed is 35 mph (56 km/h). • Maximum distance is 50 mi (80 km). Drive off slowly and smoothly without jerking the vehicle you are towing. You must only use the towing eye that was delivered with your vehicle. See Towing Points (page 164).


166


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Driving Hints


BREAKING-IN You need to break in new tires for approximately 300 miles (480
kilometers). During this time, your vehicle may exhibit some unusual driving characteristics. Avoid driving too fast during the first 1000
miles (1600 kilometers). Vary your speed frequently and change up through the gears early. Do not labor the engine. Do not tow during the first 1000 miles (1600 kilometers). REDUCED ENGINE PERFORMANCE


WARNING


Continued operation will increase the engine temperature and cause the engine to shut down completely.


If the engine coolant temperature gauge needle moves to the upper limit position, the engine is overheating. See Gauges (page 80). You must only drive your vehicle for a short distance if the engine overheats. The distance you can travel depends on ambient temperature, vehicle load and terrain. The engine will continue to operate with limited power for a short time. If the engine temperature continues to rise, the fuel supply to the engine will reduce. The air conditioning will switch off and the engine cooling fan will operate continually. 1. Reduce your speed gradually and stop your vehicle as soon as it is safe to do so.


2. Switch the engine off immediately to


prevent severe engine damage.


3. Wait for the engine to cool down.


4. Check the coolant level. See Engine


Coolant Check (page 198).


5. Have your vehicle checked by an


authorized dealer as soon as possible.


ECONOMICAL DRIVING Fuel economy is affected by several things such as how you drive, the conditions you drive under and how you maintain your vehicle. There are some things to keep in mind that may improve your fuel economy: • Accelerate and slow down in a smooth,


moderate fashion.


• Drive at steady speeds. • Anticipate stops; slowing down may


eliminate the need to stop.


• Combine errands and minimize


stop-and-go driving(When running errands, go to the furthest destination first and then work your way back home).


• Close the windows for high-speed


driving.


• Drive at reasonable speeds. •


Keep the tires properly inflated and use only the recommended size.


• Use the recommended engine oil. • Perform all regularly scheduled


maintenance.


There are also some things you may want to avoid doing because they reduce your fuel economy: • Avoid sudden or hard accelerations. • Avoid revving the engine before turning


off the car.


• Avoid long idle periods. • Do not warm up your vehicle on cold


mornings.


• Reduce the use of air conditioning and


heat.


167


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Driving Hints


• Avoid using speed control in hilly


terrain.


• Do not rest your foot on the brake


pedal while driving.


• Avoid carrying unnecessary weight. • Avoid adding particular accessories to


your vehicle (e.g. bug deflectors, rollbars/light bars, running boards, ski racks).


• Avoid driving with the wheels out of


alignment.


COLD WEATHER PRECAUTIONS The functional operation of some components and systems can be affected at temperatures below -13°F (-25°C). DRIVING THROUGH WATER


WARNING


Do not drive through flowing or deep water as you may lose control of your vehicle.


Note: Driving through standing water can cause vehicle damage. Note: Engine damage can occur if water enters the air filter. Before driving through standing water, check the depth. Never drive through water that is higher than the bottom of the front rocker area of your vehicle.


When driving through standing water, drive very slowly and do not stop your vehicle. Your brake performance and traction may be limited. After driving through water and as soon as it is safe to do so: •


Lightly press the brake pedal to dry the brakes and to check that they work.


• Check that the horn works. • Check that the exterior lights work. •


Turn the steering wheel to check that the steering power assist works.


FLOOR MATS


WARNINGS


Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that


leave the pedal area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.


Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal


injury.


168


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E176360 Driving Hints


To install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in. To remove the floor mat, reverse the installation procedure.


WARNINGS


Always make sure that the floor mats are properly attached to the retention posts in the carpet that are supplied with your vehicle. Floor mats must be properly secured to both retention posts to make sure mats do not shift out of position.


Never place floor mats or any other covering in the vehicle foot well that cannot be properly secured to


prevent them from moving and interfering with the pedals or the ability to control the vehicle.


Never place floor mats or any other covering on top of already installed floor mats. Floor mats should always rest on top of vehicle carpeting surface and not another floor mat or other covering. Additional floor mats or any other covering will reduce the pedal clearance and potentially interfere with pedal operation. Check attachment of floor mats on a regular basis. Always properly reinstall and secure floor mats that


have been removed for cleaning or replacement.


Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects that are loose can become trapped under the pedals causing a loss of vehicle control. Failure to properly follow floor mat installation or attachment instructions can potentially cause


interference with pedal operation causing a loss of vehicle control.


169


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E142666 Roadside Emergencies


ROADSIDE ASSISTANCE Vehicles Sold in the United States: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • •


24 hours a day, seven days a week. For the coverage period listed on the Roadside Assistance Card included in your Owner's Manual portfolio.


Roadside Assistance covers: • A flat tire change with a good spare, if


provided with the vehicle (except vehicles supplied with a tire inflation kit). Battery jump start. Lock-out assistance (key replacement cost is the customer's responsibility). Fuel delivery — independent service contractors, if not prohibited by state, local or municipal law, shall deliver up to 2 gal (7.6 L) of gasoline or 5 gal (18.9 L) of diesel fuel to a disabled vehicle. Roadside Assistance limits fuel delivery service to two no-charge occurrences within a 12-month period.


• Winch out — available within 100 ft


(30.5 m) of a paved or county maintained road, no recoveries. Towing — independent service contractors, if not prohibited by state, local or municipal law, shall tow Ford eligible vehicles to an authorized dealer within 35 mi (56 km) of the disablement location or to the nearest


• •




authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km).


Roadside Assistance includes up to $200
for a towed trailer if the disabled eligible vehicle requires service at the nearest authorized dealer. If the towing vehicle is operational but the trailer is not, then the trailer does not qualify for any roadside services. Vehicles Sold in the United States: Using Roadside Assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is in the owner's information portfolio in the glove compartment. United States Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company reimburses a reasonable amount for towing to the nearest dealership within 35 mi (56 km). To obtain reimbursement information, United States Ford vehicle customers call 1-800-241-3673. Customers need to submit their original receipts. Vehicles Sold in Canada: Getting Roadside Assistance Canadian customers who require roadside assistance, call 1-800-665-2006. Vehicles Sold in Canada: Using Roadside Assistance For your convenience, you may complete the roadside assistance identification card found in the centerfold of your warranty guide and retain for future reference.


170


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Roadside Emergencies


Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please refer to the coverage section of your warranty guide, call us in Canada at 1-800-665-2006, or visit our website at www.ford.ca. Sykes Assistance Services Corporation administers the Roadside Assistance program. You must receive covered services in Canada or the continental United States. Coverage extends to vehicles that use public, non-seasonal, annually traveled roadways. Roadside Assistance coverage does not extend to vehicles involved in cross-country driving, logging, autocross and any other form of off-road use. Well maintained roads and surfaces help ensure safe travel for the supplier, and allow their representatives to perform service as per the standard operating procedures. In Remote Locations If our supplier cannot take your vehicle by road to the nearest authorized dealership, transportation by rail or water may be necessary. The program covers a tow to the dock or rail terminal and also to the dealership at the end of the trip. For rail or water transportation, however, contact your authorized dealer to confirm if you are eligible for additional coverage before you authorize or pay for the service. Call Ford Roadside Assistance at 1-800-665-2006 for additional information. HAZARD WARNING FLASHERS Note: If used when the vehicle is not running, the battery will lose charge. There may be insufficient power to restart your vehicle.


The hazard warning button is located on the instrument panel. Use it when your vehicle is


creating a safety hazard for other motorists. • Press the button to turn on the hazard


warning function, and the front and rear direction indicators will flash.


• Press the button again to turn them


off.


FUEL SHUTOFF


WARNING


Failure to inspect and, if necessary, repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision.


In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision, you may restart your vehicle by doing the following: 1. Turn the ignition off. 2. Turn the ignition to crank. 3. Turn the ignition off. 4. Turn the ignition on again to re-enable


the fuel pump.


JUMP STARTING THE VEHICLE


WARNINGS


The gases around the battery can explode if exposed to flames, sparks or lit cigarettes. An explosion could result in personal injury or vehicle damage.


171


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Roadside Emergencies


WARNINGS


Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Use only an adequate-sized cable with insulated clamps.


Note: Do not disconnect the battery from your vehicle’s electrical system. Preparing Your Vehicle Note: Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. Note: Use only a 12-volt supply to start your vehicle. Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle's electrical system. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch, and switch off all accessories. Connecting the Jumper Cables


WARNING


Do not attach the cables to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points. Stay clear of moving parts. To avoid reverse polarity connections, make sure that you correctly identify the positive (+) and negative (-) terminals on both the disabled and booster vehicles before connecting the cables.


Note: In the illustration, the bottom vehicle represents the booster vehicle.


1. Connect the positive (+) jumper cable


to the positive (+) terminal of the discharged battery.


2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.


3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.


4. Make the final connection of the


negative (-) cable to an exposed metal part of the stalled vehicle's engine, or connect the negative (-) cable to a ground connection point if available.


172


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


4213E142664 Roadside Emergencies


WARNING


Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.


A spark may cause an explosion of the gases that surround the battery. Jump Starting 1. Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000
rpms, as shown in your tachometer.


2. Start the engine of the disabled vehicle. 3. After starting the disabled vehicle, run both vehicle engines for an additional three minutes before disconnecting the jumper cables.


Removing the Jumper Cables Remove the jumper cables in the reverse order that they were connected.


1. Remove the jumper cable from the ground metal surface or connecting point, if available.


2. Remove the jumper cable on the


negative (-) terminal of the booster vehicle's battery.


3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery.


4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery.


After starting your vehicle and removing the jumper cables, allow it to idle for several minutes so the battery can recharge.


173


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


E1304314132E142665 Roadside Emergencies


POST-CRASH ALERT SYSTEM The system flashes the turn signal lamps and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag (front, side, side curtain or Safety Canopy) or the safety belt pretensioners. The horn and lamps will turn off when: • •


The hazard control button is pressed The panic button (if equipped) is pressed on the remote entry transmitter Your vehicle runs out of power



174


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Customer Assistance


GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft® parts, or remanufactured or other parts that are authorized by Ford. Away From Home If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer. In the United States: Mailing address Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
Telephone 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) Online Additional information and resources are available online at www.fordowner.com


These are some of the items that can be found online: • U.S. dealer locator by Dealer Name,


City/State or Zip Code.


Ford Extended Service Plans. Ford Genuine Accessories. Service specials and promotions.


• Owner Manuals. • Maintenance Schedules. • Recalls. • • • In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6K 0C8
Telephone 1-800-565-3673 (FORD) Online www.ford.ca Twitter @FordServiceCA (English Canada) @FordServiceQC (Quebec) Additional Assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center.


3.


2.


175


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Customer Assistance



In order to help us serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. •


Your telephone number (home and business). The name of the authorized dealer and city where located. The vehicle’s current odometer reading.


• In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle.


California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18
months of ownership of a new vehicle or the first 18000 miles (29 000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR


3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time).


In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126
You are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies conferred by California Civil Code Section 1793.22(b). You are also required to use BBB AUTO LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you choose to seek redress by pursuing rights and remedies not created by California Civil Code Section 1793.22(b) or the Magnuson-Moss Warranty Act, resort to BBB AUTO LINE is not required by those statutes.


176


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Customer Assistance


THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the Services you need section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation or you do not want to participate in mediation, and if your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. You are not bound by the decision, and may reject the decision and proceed to court where all findings of the BBB Auto Line dispute, and decision, are admissible in the court action. Should you choose to accept the BBB AUTO LINE decision, Ford is then bound by the decision, and must comply with the decision within 30 days of receipt of your acceptance letter. BBB AUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have


already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 3033 Wilson Boulevard, Suite 600
Arlington, Virginia 22201
BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation. UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.


177


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing


Customer Assistance


In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada. CAMVAP services are available in all Canadian territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685
or visit www.camvap.ca. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact our Customer Relationship Center. The use of leaded fuel in your vehicle without proper conversion may damage

Loading...
x