2016 Ford Transit Connect Owners Manual

Download PDF Manual
30 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Seatbelts How to Use the Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire safety belt is pulled out. Allow the safety belt to retract. As the safety belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to Disengage the Automatic Locking Mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and return the safety belt to the vehicle sensitive (emergency) locking mode. Safety Belt Extension Assembly WARNING Do not use extensions to change the fit of the shoulder belt across the torso. If the safety belt is too short when fully extended, a safety belt extension assembly can be obtained from an authorized dealer. Only use extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label or the retractor behind the trim. Only use an extension if the safety belt is too short for you when fully extended. SEATBELT HEIGHT ADJUSTMENT WARNING Position the safety belt height adjuster so that the safety belt rests across the middle of your shoulder. Failure to adjust the safety belt correctly could reduce its effectiveness and increase the risk of injury in a crash. 1. Press the button. 2. Slide the height adjuster up or down. 3. Release the button and pull down on the height adjuster to make sure it is locked in place. 31 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E142591E1650221223Seatbelts SEATBELT WARNING LAMP AND INDICATOR CHIME Conditions of operation This lamp illuminates and an audible warning will sound if the driver's safety belt has not been fastened when the vehicle's ignition is turned on. If... Then... The driver's safety belt is not buckled before the ignition switch is turned to the on position... The driver's safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The safety belt warning light illuminates 1- 2 minutes and the warning chime sounds 4-8 seconds. The safety belt warning light and warning chime turn off. The driver's safety belt is buckled before the ignition switch is turned to the on posi- tion... The safety belt warning light and indicator chime remain off. SEATBELT REMINDER Belt-Minder™ This feature supplements the safety belt warning function by providing additional reminders that intermittently sound a tone and illuminate the safety belt warning light when you are in the driver seat or you have a front seat passenger and a safety belt is unbuckled. The system uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid the system turning on the Belt-Minder feature for objects you place on the front passenger seat, only the front seat passengers receive warnings as determined by the front passenger sensing system. If the Belt-Minder warnings expire (warnings for about five minutes) for one passenger (driver or front passenger), the other passenger can still cause the Belt-Minder feature to turn on. 32 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Seatbelts If... Then... You and the front seat passenger buckle your safety belts before you switch the ignition on or less than 1–2 minutes elapse after you switch the ignition on... You or the front seat passenger do not buckle your safety belts before your vehicle reaches at least 6 mph (9.7 km/h) and 1–2 minutes elapse after you switch the ignition on... The safety belt for the driver or front passenger is unbuckled for about 1 minute while the vehicle is traveling at least 6 mph (9.7 km/h) and more than 1–2 minutes elapse after you switch the ignition on... The Belt-Minder feature will not activate. The Belt-Minder feature activates, the safety belt warning light illuminates and a warning tone sounds for 6 seconds every 25 seconds, repeating for about 5 minutes or until you and the front seat passenger buckle your safety belts. The Belt-Minder feature activates, the safety belt warning light illuminates and a warning tone sounds for 6 seconds every 25 seconds, repeating for about 5 minutes or until you and the front seat passenger buckle your safety belts. Deactivating and Activating the Belt-Minder Feature WARNING While the system allows you to switch this feature off, the intent of the system is to remind you to wear your safety belt to improve your chance to survive an accident. We recommend you leave the system switched on for yourself and others who may use the vehicle. Note: The driver and front passenger warnings switch on and off independently. When you perform this procedure for one seating position, do not buckle the other position as this will terminate the process. Read Steps 1–4 thoroughly before proceeding with the programming procedure. Before following the procedure, make sure that: • • The parking brake is set. The transmission is in park (P) or neutral (N). The ignition is off. The driver and front passenger safety belts are unbuckled. • • 1. Switch the ignition on. Do not start the vehicle. 2. Wait until the safety belt warning light turns off (about 1 minute). After Step 2, wait an additional 5 seconds before proceeding with Step 3. Once you start Step 3, you must complete the procedure within 30 seconds. 3. For the seating position you are switching off, buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. After Step 3, the safety belt warning light turns on. 33 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Seatbelts 4. While the safety belt warning light is on, buckle and then unbuckle the safety belt. After Step 4, the safety belt warning light flashes for confirmation. This will switch the feature off for that seating position if it is currently on. This will switch the feature on for that seating position if it is currently off. • • CHILD RESTRAINT AND SEATBELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All vehicle safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seat back (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a crash. Read the child restraint manufacturer's instructions for additional inspection and maintenance information specific to the child restraint. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a crash should also be inspected and replaced if either damage or improper operation is noted. Properly care for safety belts. See Vehicle Care (page 214). 34 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Personal Safety System™ How Does the Personal Safety System Work? The Personal Safety System can adapt the deployment strategy of the safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the restraints control module. During a crash, the restraints control module may deploy the safety belt pretensioners, one or both stages of the dual-stage airbags based on crash severity and occupant conditions. The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. The Vehicle Personal Safety System consists of: • Driver and passenger dual-stage airbag supplemental restraints. Front seat outboard safety belts with pretensioners, energy management retractors and safety belt usage sensors. • Driver seat position sensor. • • Passenger airbag off and on indicator Front passenger sensing system. lamp. Front crash severity sensors. • • Restraints control module with impact and safing sensors. • Restraint system warning light and backup tone. The electrical wiring for the airbags, crash sensors, safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system and indicator lights. • • 35 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Supplementary Restraints System PRINCIPLE OF OPERATION WARNINGS Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. All occupants of your vehicle, including the driver, should always properly wear their safety belts, even when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Failure to follow this could seriously increase the risk of injury or death. Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back. Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses as you could be seriously injured or killed. Contact your authorized dealer as soon as possible. Several airbag system components get hot after inflation. Do not touch them after inflation as this may result in serious injury. If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash. The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys. This is normal. The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (for example, baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions or swelling. Temporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. Routine maintenance of the airbags is not required. 36 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Supplementary Restraints System DRIVER AND PASSENGER AIRBAGS WARNINGS Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury. Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back. The driver and front passenger airbags will deploy during significant frontal and near frontal crashes. The driver and passenger front airbag system consists of: • Driver and passenger airbag modules. • Front passenger sensing system. · Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator (page 43). Proper Driver and Front Passenger Seating Adjustment WARNING National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly (one or two degrees) from the upright position. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. Children and Airbags WARNING Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back. 37 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E151127Supplementary Restraints System WARNINGS To reduce the risk of possible serious injury: Do not stow objects in seatback map pocket or hang objects off seatback if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console. Check the passenger airbag indicator lamp for proper airbag status. Failure to follow these instructions may interfere with the front passenger seat sensing system. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a crash. FRONT PASSENGER SENSING SYSTEM Any alteration or modification to the front passenger seat may affect the performance of the front passenger sensing system. This system works with sensors that are part of the front passenger seat and safety belt to detect the presence of a properly-seated occupant and determine if the front passenger frontal airbag should be enabled (may inflate) or not. WARNINGS Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. The front passenger sensing system uses a passenger airbag indicator which will illuminate indicating that the front passenger frontal airbag is either ON (enabled) or OFF (disabled). The indicator lamp is located at the top center of the instrument panel. Note: When the ignition is first tuned on, the indicator lamps will illuminate for a short period of time to confirm it is functional. 38 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E142846E170286Supplementary Restraints System The front passenger sensing system is designed to disable (will not inflate) the front passenger frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology, parents are strongly encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag when the passenger seat is empty. • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the OFF indicator lamp will illuminate and stay illuminated to remind you that the front passenger frontal airbag is disabled. If the child restraint has been installed and the passenger airbag status indicator illuminates the ON lamp, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer's instructions. • The front passenger sensing system is designed to enable (may inflate) the front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat. • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the ON indicator lamp will be unlit and stay unlit. If a person of adult size is sitting in the front passenger seat, but the airbag OFF indicator lamp is illuminated, it is possible that the person is not sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the full upright position. • Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended. • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger frontal airbag. If the OFF indicator lamp remains illuminated even after this, the person should be advised to ride in the rear seat. • Occupant Empty Child Adult Passenger airbag OFF indic- ator Passenger airbag Disabled Disabled Enabled OFF: Lit ON: Unlit OFF: Lit ON: Unlit OFF: Unlit ON: Lit 39 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Supplementary Restraints System If the airbag readiness light is illuminated, do the following: The driver and adult passengers should check for objects lodged underneath the front passenger seat, or cargo interfering with the seat. If there are lodged objects, or cargo is interfering with the seat, take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver and adult passengers should check for any objects lodged underneath the front passenger seat or cargo interfering with the seat. • Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least two minutes and verify that the airbag readiness light is no longer illuminated. If the airbag readiness light remains illuminated, this may or may not be a problem due to the front passenger sensing system. • Do not attempt to repair or service the system. Take your vehicle immediately to an authorized dealer. If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center. See Getting the Services You Need (page 175). Note: When the passenger airbag OFF light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbag deployment injuries. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • Objects lodged underneath the seat. • Objects between the seat cushion and the center console. • Objects hanging off the seatback. • Objects stowed in the seatback map pocket. • Objects placed on the occupant's lap. • Cargo interference with the seat. • Other passengers pushing or pulling on the seat. • Rear passenger feet and knees resting or pushing on the seat. The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above. Make sure the front passenger sensing system is operating properly. See Crash Sensors and Airbag Indicator (page 43). 40 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Supplementary Restraints System SIDE AIRBAGS WARNINGS Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash. Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair, or modify the airbag, its fuses or the seat cover on a seat containing an airbag as you could be seriously injured or killed. Contact your authorized dealer as soon as possible. If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash. The side airbags are located on the outboard side of the seatbacks of the front seats. In certain sideways crashes, the airbag on the side affected by the crash will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact crashes. The system consists of the following: • A label or embossed side panel indicating that side airbags are fitted to your vehicle. Side airbags located inside the driver and front passenger seatbacks. Front passenger sensing system. • • • Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator (page 43). Note: The passenger sensing system will deactivate the passenger seat-mounted side airbag if it detects an empty passenger seat. The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. 41 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E152533Supplementary Restraints System SAFETY CANOPY™ WARNINGS Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying curtain airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash. Do not lean your head on the door. The curtain airbag could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the curtain airbags, its fuses, the A, B, C, or D pillar trim, or the headliner on a vehicle containing curtain airbags as you could be seriously injured or killed. Contact your authorized dealer as soon as possible. All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death. To reduce risk of injury, do not obstruct or place objects in the deployment path of the curtain airbag. If the curtain airbags have deployed, the curtain airbags will not function again. The curtain airbags (including the A, B, C and D pillar trim and headliner) must be inspected and serviced by an authorized dealer. If the curtain airbag is not replaced, the unrepaired area will increase the risk of injury in a crash. The Safety Canopy will deploy during significant side crashes or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopy is mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. In certain sideways crashes or rollover events, the Safety Canopy will be activated, regardless of which seats are occupied. The Safety Canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact crashes and rollover events. The system consists of the following: • Safety canopy curtain airbags located above the trim panels over the front and rear side windows identified by a label or wording on the headliner or coat hook. • A flexible headliner which opens above the side doors to allow air curtain deployment. • The crash sensors and monitoring system have a readiness indicator. See Crash Sensors and Airbag Indicator (page 43). 42 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E75004Supplementary Restraints System Children 12 years old and under should always be properly restrained in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The design and development of the Safety Canopy included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy). CRASH SENSORS AND AIRBAG INDICATOR WARNING Modifying or adding equipment to the front end of your vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of your vehicle. Your vehicle has a collection of crash and occupant sensors which provide information to the restraints control module which deploys (activates) the front safety belt pretensioners, driver airbag, passenger airbag, seat mounted side airbags, and the Safety Canopy. Based on the type of accident (frontal impact, side impact or rollover) the restraints control module will deploy the appropriate safety devices. The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. A warning indicator light in the instrument cluster indicates the readiness of the safety system. If this warning indicator light is not functioning and there is another fault within the system, the message cluster may display an airbag failure warning. See Information Displays (page 85). You will hear five tones that repeat periodically until you repair the problem, the warning indicator light or both. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following: • • The readiness light will not illuminate immediately after the ignition is turned on. The readiness light will either flash or stay lit. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem, the light or both are repaired. If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash. The safety belt pretensioners and the airbag supplemental restraint system is designed to activate when your vehicle sustains frontal or sideways deceleration sufficient to cause the restraints control module to deploy a safety device or when a certain likelihood of a rollover event is detected by the rollover sensor. 43 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Supplementary Restraints System The fact that the safety belt pretensioners or airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (for example, crash severity, belt usage) were not appropriate to activate these safety devices. • The design of the front airbags is to activate only in frontal and near-frontal crashes (not rollovers, side impacts or rear impacts) unless the crash causes sufficient frontal deceleration. The safety belt pretensioners are designed to activate in frontal, near-frontal, side and rollover crashes. The design of the side airbags is to inflate in certain side crashes. Side airbags may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation. The design of the Safety Canopy is to inflate in certain side impact crashes and when a certain likelihood of rollover is detected by the rollover sensor. The Safety Canopy may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation, or a certain likelihood of rollover. • • • AIRBAG DISPOSAL Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel. 44 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Keys and Remote Controls Note: The remote control contains sensitive electrical components. Exposure to moisture or impact may cause permanent damage. REMOTE CONTROL Integrated Keyhead Transmitter (If Equipped) Type 1 Type 2 Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control. GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. The typical operating range for your transmitter is approximately 33 feet (10 meters). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range: • weather conditions nearby radio towers • structures around the vehicle • other vehicles parked next to your • vehicle The radio frequency used by your remote control can also be used by other short distance radio transmissions, for example amateur radios, medical equipment, wireless headphones, remote controls and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key. Note: Make sure to lock your vehicle before leaving it unattended. Note: If you are in range, the remote control will operate if you press any button unintentionally. 45 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E142585E177585Keys and Remote Controls Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally. Integrated Keyhead Transmitter Note: Your vehicle’s keys came with a security label that provides important vehicle key cut information. Keep the label in a safe place for future reference. Programming a New Remote Control You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. See Passive Anti-Theft System (page 58). Reprogramming the Unlocking Function Note: When you press the unlock button only the driver and passenger doors are unlocked. Pressing the unlock button again unlocks all the doors. This is the default setting. See Locking and Unlocking (page 53). Press and hold the unlock and lock buttons on the remote control simultaneously for at least four seconds with the ignition off. The direction indicators will flash twice to confirm the change. To return to the original unlocking function, repeat the process. Replacing the Battery The remote control uses one coin type three volt lithium battery CR2032 or equivalent. 1. Twist a thin coin in the slot of the transmitter near the key ring to remove the battery cover. 2. Remove the old battery. 3. Insert the new battery. Refer to the instructions inside the transmitter for the correct orientation of the battery. Press the battery down to make sure it is fully in the housing. 4. Snap the battery cover back onto the transmitter. 46 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E138615E138619E138620Keys and Remote Controls Car Finder Press the lock button on the key twice within three seconds. The horn sounds and the direction indicators will flash. Note: If locking was not successful or if any door or the liftgate is open, or if the hood is open on vehicles with a perimeter alarm or remote start, the horn will sound and the direction indicators will not flash. REPLACING A LOST KEY OR REMOTE CONTROL You can purchase replacement keys or remote controls from an authorized dealer. Authorized dealers can program remote controls for your vehicle. See Remote Control (page 45). To re-program the passive anti-theft system see an authorized dealer. 47 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing MyKey™ PRINCIPLE OF OPERATION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys. They can be used to: • Create a MyKey. • Program configurable MyKey settings. • Clear all MyKey features. When you have programmed a MyKey, you can access the following information using the information display: • How many admin keys and MyKeys are programmed to your vehicle. The total distance your vehicle has traveled using a MyKey. Note: All MyKeys are programmed to the same settings. You cannot program them individually. Non-configurable Settings The following settings cannot be changed by an admin key user: • Belt-Minder or safety belt reminder. You cannot disable this feature. The audio system will mute when the front seat occupants’ safety belts are not fastened. Early low fuel. The low fuel warning is activated earlier, giving the MyKey user more time to refuel. • • • Driver assist features, if equipped on your vehicle, are forced on: parking aid, blind spot information system (BLIS) with cross traffic alert, lane departure warning and forward collision warning system. Satellite radio adult content restrictions (available only in some markets). • Configurable Settings With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the vehicle. You can also change the settings afterward with an admin key: • A vehicle speed limit can be set. Warnings will be shown in the display, followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal or by setting cruise control. WARNING Do not set MyKey maximum speed limit to a limit that will prevent the driver from maintaining a safe speed considering posted speed limits and prevailing road conditions. The driver is always responsible to drive in accordance with local laws and prevailing conditions. Failure to do so could result in accident or injury. 48 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing MyKey™ • Various vehicle speed minders can be set. Once you select a speed, it will be shown in the display, followed by an audible tone when the preselected vehicle speed is exceeded. • Audio system maximum volume of 45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled. • Always on setting. When this is selected, you will not be able to turn off Advance Trac or traction control, 911 Assist or Emergency Assistance, or Do Not Disturb (if your vehicle is equipped with these features). CREATING A MYKEY You can program a MyKey using the information display control on the steering wheel. See Information Displays (page 85). Insert the key you want to program into the ignition and switch the ignition on. Press the left arrow button to access the main menu and scroll to: Message Settings MyKey Create MyKey Action and Description Press the OK button. Press the OK button. When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at your vehicle's next start. Make sure you label the key so you can distinguish it from the admin keys. You can also program configurable settings for the key(s). Refer to the following Programming/Changing Configur- able Settings. Programming/Changing Configurable Settings Switch the ignition on using an admin key or fob. Use the information display to access the configurable MyKey settings, scroll to: Message Action and Description Settings MyKey Press the OK button. Use the up and down arrow buttons to scroll to a configurable feature. Press the OK or right arrow button to make a selection. 49 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing MyKey™ Message Action and Description Choose your applicable setting. Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you switch the ignition off you will need an admin key to change or clear your MyKey settings. Switch the ignition on using an admin key or remote control. CLEARING ALL MYKEYS You can clear or change your MyKey settings using the information display control on the steering wheel. See Information Displays (page 85). To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scroll to: Message Action and Description Settings MyKey Clear MyKey Press the OK button. Press the OK button. Press and hold the OK button until the following message displays. All MyKeys Cleared Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status. 50 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing MyKey™ CHECKING MYKEY SYSTEM STATUS You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 85). To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll to: Message Description Settings MyKey Select one of the following: MyKey Dist. Press the OK button. Press the OK button. Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear your MyKeys. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey. Indicates the number of MyKeys programmed to your vehicle. Use this feature to detect how many MyKeys you have for your vehicle and determine when a MyKey has been deleted. Indicates how many admin keys are programmed to your vehicle. Use this feature to determine how many unrestricted keys you have for your vehicle, and detect if an additional MyKey has been programmed. {0} MyKeys {0} Admin Keys 51 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing MyKey™ USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non MYKEY TROUBLESHOOTING Condition I cannot program a MyKey. I cannot program the configurable settings. I cannot clear the MyKeys. I lost the only admin key. I lost a key. MyKey distance does not accumulate. Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system. Potential Causes · The key used to start your vehicle does not have admin privileges. · The key used to start your vehicle is the only admin key (there always has to be at least one admin key). · SecuriLock passive anti-theft system is disabled or in unlimited mode. · The key used to start your vehicle does not have admin privileges. · No keys are programmed to the vehicle. See Creating a MyKey (page 49). · The key used to start your vehicle does not have admin privileges. · No MyKeys are programmed to the vehicle. See Creating a MyKey (page 49). Purchase a new key from your authorized dealer. Program a spare key. See Passive Anti- Theft System (page 58). · The MyKey user is not using the MyKey. · An admin key holder cleared the MyKeys and created new MyKeys. · The key system has been reset. 52 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Locks Locking the Doors Press the button to lock all doors. The direction indicators flash. Press the button again within three seconds to confirm that all the doors are closed. The doors lock again, the horn sounds and the direction indicators flash if all the doors and the liftgate are closed. Note: If any door or the luggage compartment is not closed, or if the hood is not closed on vehicles that have an anti-theft alarm or remote start, the horn will not chirp. Locking and Unlocking the Doors From Inside The power door lock control is located on the driver and passenger doors. Press the button to lock or unlock all the doors. The lamp illuminates with the doors locked. Opening the Double Rear Doors WARNING If there is a ladder fitted to the rear cargo door, do not open the door fully if the side-loading door is open. LOCKING AND UNLOCKING Remote Control You can use the remote control at any time. Unlocking the Doors The position lamps illuminate when you unlock the doors. They automatically turn off when you switch the ignition on. Note: You can unlock the driver door with the key. Use the key when the remote control is not functioning. Note: When you lock your vehicle for several weeks, the remote control will be switched off. Your vehicle must be unlocked and the engine started using the key. Unlocking and starting your vehicle once will enable the remote control. One-Stage Unlocking Press the button to unlock all doors. The direction indicators flash. Two-Stage Unlocking Press the button to unlock the front doors. Press the button again within three seconds to unlock all doors. The direction indicators flash. Reprogramming the Unlocking Function Press and hold both the lock and unlock buttons on the remote control for three seconds to change between one-stage and two-stage unlocking. The direction indicators flash twice to indicate a change to the unlocking mode. 53 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E102566E148805Locks Unlocking with the Key Turn the top of the key toward the rear of your vehicle. Unlocking the Doors with the Interior Door Handles You can unlock individual doors by pulling the relevant interior door handle. Pulling the driver door interior door handle will unlock all the doors, if auto unlock has been enabled. Rear Door Unlocking and Opening Pull the interior door release handle twice to unlock and open the rear door. The first pull unlocks the door and the second pull will unlatch the door. Smart Unlocks For Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition. When you open one of the front doors and lock your vehicle with the power door lock control, all the doors will lock then unlock if your key is still in the ignition. You can still lock your vehicle with the key in the ignition by pressing the lock button on the transmitter even if the doors are not closed. If both front doors are closed you can lock your vehicle by any method, regardless of whether the key is in the ignition or not. 1. Open the rear cargo door. 2. Press the button. 3. Open the cargo door fully. Locking and Unlocking the Doors with the Key Note: Do not leave your keys in your vehicle. Locking with the Key Turn the top of the key toward the front of your vehicle. 54 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E148806E1890912Locks Auto lock and Auto unlock Feature Auto lock The Auto lock feature will lock the doors and liftgate when all of the following conditions have been met: • All doors are closed. • • The ignition is on. Your vehicle is moving at a speed greater than 4 mph (7 km/h) for more than two seconds. Auto unlock The auto unlock feature will unlock all the doors when all of the following conditions have been met: • The ignition is on, all doors are closed, and your vehicle is moving at a speed greater than 4 mph (7 km/h) for more than two seconds. Your vehicle has come to a stop and you switch the ignition off or to the accessory position. The driver door is opened within 10 minutes of you switching the ignition off or to the accessory position. • • Note: The doors will not auto unlock if your vehicle has been electronically locked after the ignition is turned off and before the driver door is opened. Enabling or Disabling Auto lock and Auto unlock Note: An authorized dealer or you can carry out this procedure. To enable or disable these features, do the following: 1. Switch the ignition on. 2. Press the power door unlock button three times. 4. Press the power door unlock button three times. 5. Switch the ignition on. The horn will chirp indicating your vehicle is in programming mode. Auto lock: Press the power door unlock button and within five seconds, press the power door lock button. The horn sounds once if disabled or twice if enabled. Auto unlock: Press the power door lock button and within five seconds, press the power door unlock button. The horn sounds once if disabled or twice if enabled. After programming the feature, switch the ignition off. The horn will chirp once indicating programming is complete. Note: You will have 30 seconds to complete the procedure. Note: You can enable or disable the auto unlock feature independently of the auto lock feature. Emergency Locking with the Key Note: If the child safety locks are on and you pull the interior handle, you will only turn off the emergency locking not the child safety lock. You can only open the doors using the external door handle. Note: If the doors have been unlocked using this method, the doors must be locked individually until the central locking function has been repaired. Note: When the central locking function fails to operate, lock the doors individually using the key in the position shown. 3. Switch the ignition off. 55 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Locks MANUAL LIFTGATE WARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of your vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Make sure everyone in your vehicle is in a seat and properly using a safety belt. Failure to follow this warning could result in serious personal injury or death. Left-Hand Side Turn clockwise to lock. Right-Hand Side Turn counterclockwise to lock. Rear Emergency Exit (If Equipped) Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury. Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not hang anything from the spoiler, rear window or liftgate, for example a bike rack. This could damage the liftgate and its components. Opening and Closing the Liftgate To Open the Liftgate 1. Press the unlock button, or the tailgate unlock button on the remote key. Slide the release lever up to open the door in an emergency. 56 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E112203E180300Locks 2. Press the release button above the license plate to unlatch the liftgate. Note: Do not leave the liftgate open while driving. To Close the Liftgate 57 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E190028E148833Security PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting problems if they are too close to the key when starting the engine. Prevent these objects from touching the coded key while starting the engine. Switch the ignition off, move all objects on the key chain away from the coded key and restart the engine if a problem occurs. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle. SecuriLock® The system is an engine immobilization system. It is designed to help prevent the engine from being started unless a correctly coded key for your vehicle is used. Using an incorrectly coded key may prevent the engine from starting. A message may appear in the information display. If you are unable to start the engine with a correctly coded key, a malfunction has happened and a message may appear in the information display. Automatic Arming The engine immobilization system arms immediately after you switch the ignition off. Automatic Disarming Switching the ignition on with a correctly coded key disarms the engine immobilization system. Replacement Keys The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control. If your keys are lost or stolen and you do not have a spare correctly coded key, you will need to have your vehicle towed to an authorized dealer. You need to erase the coded keys from your vehicle and program new coded keys. Store an extra correctly coded key away from the vehicle in a safe place to help prevent any inconveniences. See an authorized dealer to purchase additional spare or replacement keys. Note: Your vehicle comes with two integrated keyhead transmitters. Programming a Spare Integrated Keyhead Transmitter You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry portion of the remote control to your vehicle Only use integrated keyhead transmitters or standard SecuriLock keys. You must have two previously programmed correctly coded keys and the new unprogrammed key readily accessible. See an authorized dealer to have the spare key programmed if two previously programmed correctly coded keys are not available. Read and understand the entire procedure before you begin. 58 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Security 1. Insert the first previously programmed correctly coded key into the ignition. 2. Switch the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds. 3. Switch the ignition off and remove the first correctly coded key from the ignition. 4. After three seconds but within 10 seconds of switching the ignition off, insert the second previously correctly coded key into the ignition. 5. Switch the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds. 6. Switch the ignition off and remove the second previously programmed correctly coded key from the ignition. 7. After three seconds but within 10 seconds of switching the ignition off and removing the previously programmed correctly coded key, insert the new unprogrammed key into the ignition. 8. Switch the ignition from off to on. Keep the ignition on for at least six seconds. 9. Remove the newly programmed correctly coded key from the ignition. If the key has been successfully programmed it will start the engine and operate the remote entry system (if the new key is an integrated keyhead transmitter). If the key was not successfully programmed, wait 10 seconds and repeat Steps 1 through 8. If you are still unsuccessful, take your vehicle to an authorized dealer. Note: You can program a maximum of eight coded keys to your vehicle. All eight can be integrated keyhead transmitters. 59 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing Steering Wheel ADJUSTING THE STEERING WHEEL WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 103). 3. Lock the steering column. AUDIO CONTROL Select the required source on the audio unit. 1. Unlock the steering column. 2. Adjust the steering wheel to the desired position. 60 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing 122E951783E95179Steering Wheel You can operate the following functions with the control: VOICE CONTROL Press the button to select or deselect voice control. See SYNC™ (page 274). CRUISE CONTROL Volume up. Seek up, next or end call. Volume down. Seek down, previous or accept call. Seek, Next or Previous Press the seek button to: • Tune the radio to the next or previous stored preset. • Play the next or the previous track. Press and hold the seek button to: • Tune the radio to the next station up or down the frequency band. Seek through a track. • See Using Cruise Control (page 140). 61 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E159789ABCDE159531E142437Steering Wheel INFORMATION DISPLAY CONTROL See Information Displays (page 85). 62 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E130248Wipers and Washers WINDSHIELD WIPERS Note: Fully defrost the windshield before you switch the windshield wipers on. Note: Make sure you switch the windshield wipers and vehicle power off before using an automatic car wash. Note: If streaks or smears appear on the windshield, clean the windshield and the wiper blades. See Checking the Wiper Blades (page 202). If that does not resolve the issue, install new wiper blades. See Changing the Wiper Blades (page 202). Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield. Single wipe. Intermittent wipe. Normal wipe. High-speed wipe. Note: Move to position O marked on the wiper lever to switch off. Intermittent Wipe Short-wipe interval. Intermittent wipe. Long-wipe interval. Push the wiper lever up to switch the wipers on, and then use the rotary control to adjust the intermittent wipe interval. Speed Dependent Wipers (If Equipped) When your vehicle speed increases, the interval between wipes decreases. AUTOWIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Check your wipers before you enter a car wash to make sure you switched them off. The autowipers feature uses a rain sensor. You can find it in the area around the interior mirror. The rain sensor monitors the amount of moisture on the windshield and automatically turns on the wipers. It adjusts the wiper speed by the amount of moisture that the sensor detects on the windshield. 63 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E197525E197526Wipers and Washers Use the rotary control to adjust the sensitivity of the rain sensor: • Rotate the control down to low sensitivity, and the wipers turn on when the rain sensor detects a large amount of moisture on the windshield. • When you move the wiper lever up to the first position and the autowiper system is on, the autowiper sensitivity setting adjusts the wiper speed according to the moisture on the windshield only. Highest sensitivity. On. Lowest sensitivity. Switch the autowipers on by moving the wiper lever up to the first position. Switch the autowipers off by moving the wiper lever down. • When you lower the sensitivity, the wipers remain in their ready position only. They do not wipe the windshield automatically unless the sensor detects moisture. • Move the wiper lever position up to the second position to wipe the windshield on-demand. • Rotate the control up to high sensitivity, and the wipers turn on when the rain sensor detects a small amount of moisture on the windshield. • When you set the wiper control to a higher sensitivity, the wipers wipe the windshield once. • Remember to move the wiper lever position up to the second position to wipe the windshield on-demand. The autowipers feature is active and ready when the wiper lever is in the first position and selected in the information display. You can change the autowipers feature to intermittent wipers through the information display. See (page 85). Note: Check your wiper function in the information display. See (page 85). The autowipers feature functions only when you select the menu choice in the information display and you move the wiper lever up to the first position. The autowipers feature then remains on in the information display menu until you change it to intermittent wipe. 64 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E197429Wipers and Washers Note: If you switch autolamps on in conjunction with autowipers, your low beam headlamps turn on automatically when the rain sensor activates the windshield wipers continuously. See Autolamps (page 68). Keep the outside of the windshield clean. The rain sensor is very sensitive. If the area around the mirror is dirty, then the wipers may operate if dirt, mist or insects hit the windshield. Wet or winter driving conditions with ice, snow or salty road mist can cause inconsistent and unexpected wiping or smearing. In these conditions, you can do the following to help keep your windshield clear: • Lower the sensitivity of the autowipers to reduce the amount of smearing. Switch to normal or high-speed wipe by moving the wiper lever up. Switch the autowipers off and switch intermittent mode on through the information display. See (page 85). Switch the autowipers off by moving the wiper lever down. • • • Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. See Changing the Wiper Blades (page 202). WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat. To operate the washers and spray the windshield, pull the lever toward you. When you release the lever, the wipers will operate for a short time. REAR WINDOW WIPER AND WASHERS Rear Window Wiper Note: Make sure you switch the rear window wiper and ignition off before using an automatic car wash. Intermittent wipe. Low speed wipe. Off. Press the top of the button to switch intermittent wipe on. Press the top of the button again to switch low speed wipe on. Press the bottom of the button to switch the rear window wiper off. 65 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E197528E197647Wipers and Washers When you switch on the front wipers and move the gearshift lever to reverse (R), rear intermittent wipe automatically turns on. Rear Window Washer Push the lever away from you to operate the rear window washer. When you release the lever, wiping continues for a short period of time. 66 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E197529Lighting GENERAL INFORMATION Condensation in Lamp Assemblies Exterior lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. Examples of acceptable condensation are: • The presence of a fine mist (no streaks, drip marks or large droplets). • A fine mist covers less than 50% of the lens. Examples of unacceptable condensation are: • A water puddle inside the lamp. • Streaks, drip marks or large droplets present on the interior of the lens. If you see any unacceptable condensation, have your vehicle checked by an authorized dealer. LIGHTING CONTROL Off. Instrument panel lamps, license plate lamps and tail lamps. Headlamps. High Beams Push the lever away from you to switch the high beam on. Push the lever forward again or pull the lever toward you to switch the high beams off. 67 Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, First Printing E142449E162679Lighting Headlamp Flasher Slightly pull the lever toward you and release it to flash the headlamps. AUTOLAMPS (If Equipped) WARNING The autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog. Always ensure that your headlamps are switched to auto or on, as appropriate, during all low visibility conditions. Failure to do so may result in a collision. If equipped, the following also activate when the lighting control is in the autolamps position and you switch them on in the information display: • Configurable daytime running lamps. • Automatic high beam control. • Adaptive headlamp control. The headlamps remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps remain on. See Information Displays (page 85). Note: With the headlamps in the autolamps position, you cannot switch the high beam headlamps on until the autolamps system turns the low beam headlamps on. Windshield Wiper Activated Headlamps The windshield wiper activated headlamps turn on within 10 seconds when you switch the windshield wipers on and the lighting

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2016 Ford Transit Connect Owners Manual