Download PDF Manual

fire hazard.


• Use as short an extension cord as


possible.


• Do not use multiple extension cords.


111


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Fuel and Refueling


SAFETY PRECAUTIONS


WARNINGS


Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray


and fire.


The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.


Automotive fuels can cause serious injury or death if misused or mishandled. Flow of fuel through a fuel pump nozzle can produce static electricity. This can cause a fire if you are filling


an ungrounded fuel container.


Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.


Observe the following guidelines when handling automotive fuel: •


Extinguish all smoking materials and any open flames before refueling your vehicle.


• Always turn off the vehicle before


refueling.


• Automotive fuels can be harmful or


fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.


• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.


• Avoid getting fuel liquid in your eyes. If


fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin, clothing or both, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.




112


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Fuel and Refueling


FUEL QUALITY Note: Use of any fuel other than those recommended may cause vehicle damage, a loss of vehicle performance and repairs may not be covered under warranty. Choosing the Right Fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 15% ethanol. Do not use fuel ethanol (E85), diesel fuel, fuel-methanol, leaded fuel or any other fuel because it could damage or impair the emission control system. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. The use of leaded fuel is prohibited by law. Octane Recommendations 2.5L engine Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some fuel stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87
are not recommended. 1.6L EcoBoost® engines Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as "Regular" with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended. Premium fuel will provide improved performance and is recommended for severe duty usage such as trailer tow.


Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage. RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: •


You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. With keyless ignition, just start the engine. Crank time will be longer than usual.


• Normally, adding 1 gallon (3.8 liters) of fuel is enough to restart the engine. If your vehicle is out of fuel and on a steep grade, more than 1 gallon (3.8
liters) may be required.


Refilling With a Portable Fuel Container


WARNINGS


Do not insert the nozzle of portable fuel containers or aftermarket funnels into the capless fuel system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, which could result in serious personal injury.


Do not try to pry open or push open the capless fuel system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others.


113


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Fuel and Refueling


Note: Do not use aftermarket funnels; they will not work with the capless fuel system and can damage it. The included funnel has been specially designed to work safely with your vehicle. Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the


ground.



• Do not fill a fuel container while it is in the vehicle (including the cargo area). Keep the fuel pump nozzle in contact with the fuel container while filling. • Do not use a device that would hold


the fuel pump handle in the fill position. When filling your vehicle’s fuel tank from a portable fuel container, use the funnel included with your vehicle.


1. Locate the plastic funnel in the glove


box.


2. Slowly insert the funnel into the


capless fuel system.


3. Fill your vehicle with fuel from the


portable fuel container.


4. When done, clean the funnel or


properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel.


REFUELING


WARNINGS


Fuel vapor burns violently and a fuel fire can cause severe injuries. Read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, flames and smoking materials away from fuel. Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is


against the law in some places.


Keep children away from the fuel pump; never let children pump fuel. Do not use personal electronic devices while refueling.


Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the


ground.



• Do not fill a fuel container while it is in the vehicle (including the cargo area). Keep the fuel pump nozzle in contact with the fuel container while filling. • Do not use a device that would hold


the fuel pump handle in the fill position.


114


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E142668 Fuel and Refueling


Easy Fuel™ Capless Fuel System


WARNING


The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.


When fueling your vehicle: 1. Put the vehicle in P (Park) and turn the


ignition off.


2. Open the fuel filler door.


3. Slowly insert the fuel filler nozzle fully


into the fuel system, and leave the nozzle fully inserted to open both doors until you are done pumping. Hold handle higher during insertion for easier access.


4. After you are done pumping fuel, slowly


remove the fuel filler nozzle—allow about five to ten seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle.


Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuel filler nozzle. The overfilled fuel may run down the drain located below and in front of the fuel filler door. If the fuel fill inlet was not properly closed, a service engine warning lamp may appear on the instrument cluster. At the next opportunity, do the following: 1. Safely pull off the road. 2. Put the vehicle in P (Park) and turn the


ignition off.


3. Open the fuel filler door and remove


any visible debris from the fuel fill opening. Insert either the fuel fill nozzle or the fuel fill funnel provided with the vehicle several times to allow the inlet to close properly. This will dislodge any debris preventing the inlet from sealing.


4.


If this action corrects the problem, the warning lamp may not reset immediately. It may take several driving cycles for the warning lamp to turn off. A driving cycle consists of an engine start-up (after four or more hours with the engine off) followed by city or highway driving.


115


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E156032E154765 Fuel and Refueling


FUEL CONSUMPTION Note: The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty. Do not rely on this fuel for driving. The usable capacity of the fuel tank is the amount of fuel that can be put into the tank after the gauge indicates empty. The advertised capacity is the total fuel tank size – it is the combined usable capacity plus the empty reserve. Filling the Tank For consistent results when filling the fuel tank: •


Turn the ignition off before fueling; an inaccurate reading results if the engine is left running.


• Use the same fill rate


(low-medium-high) each time the tank is filled.


• Allow no more than two automatic


click-offs when filling.


Results are most accurate when the filling method is consistent. Calculating Fuel Economy Do not measure fuel economy during the first 1000 miles (1600 kilometers) of driving (this is your engine’s break-in period); a more accurate measurement is obtained after 2000 miles - 3000 miles (3200 kilometers - 4800 kilometers). Also, fuel expense, frequency of fill ups or fuel gauge readings are not accurate ways to measure fuel economy.


1. Fill the fuel tank completely and record


the initial odometer reading.


2. Each time you fill the tank, record the


amount of fuel added.


3. After at least three to five tank fill ups, fill the fuel tank and record the current odometer reading.


4. Subtract your initial odometer reading


from the current odometer reading. 5. Calculate fuel economy by dividing miles traveled by gallons used (For Metric: Multiply liters used by 100, then divide by kilometers traveled).


Keep a record for at least one month and record the type of driving (city or highway). This provides an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter show how temperature impacts fuel economy. In general, lower temperatures mean lower fuel economy. EMISSION CONTROL SYSTEM


WARNINGS


Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the


engine compartment and exhaust system, which can start a fire.


Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If


you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.


116


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Fuel and Refueling


Your vehicle is equipped with various emission control components and a catalytic converter that will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your


vehicle is moving, especially at high speeds.


• Have the items listed in scheduled


maintenance information performed according to the specified schedule. The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system. If you use parts other than Ford, Motorcraft or Ford-authorized parts for maintenance replacements, or for service of components affecting emission control, such non-Ford parts should be the equivalent to genuine Ford Motor Company parts in performance and durability. Illumination of the service engine soon indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly. An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove


an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal also lists engine displacement Please consult your warranty information for complete details. On-Board Diagnostics (OBD-II) Your vehicle is equipped with an on-board diagnostics system (OBD-II) that monitors the engine’s emission control system. This system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also assists your authorized dealer in properly servicing your vehicle. When the service engine soon indicator illuminates, the OBD-II system has detected a


malfunction. Temporary malfunctions may cause the service engine soon indicator to illuminate. Examples of temporary malfunctions are: •


the vehicle has run out of fuel—the engine may misfire or run poorly poor fuel quality or water in the fuel—the engine may misfire or run poorly the fuel fill inlet may not have been properly closed See Refueling (page 114). driving through deep water—the electrical system may be wet. You can correct these temporary malfunctions by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions





117


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Fuel and Refueling


If the vehicle’s engine or transmission has just been serviced, or the battery has recently run down or been replaced, the OBD-II system may indicate that the vehicle is not ready for I/M testing. To determine if the vehicle is ready for I/M testing, turn the ignition key to the on position for 15 seconds without cranking the engine. If the service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system monitors the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, you may need to perform the following driving cycle consisting of mixed city and highway driving: Drive on an expressway or highway for a steady 15 minutes, followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, you will have to repeat the above driving cycle.


present, the service engine soon indicator should stay off the next time you start the engine. A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required. If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity. Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the service engine soon indicator on can result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and lead to more costly repairs. Readiness for Inspection/Maintenance (I/M) Testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.


If the service engine soon indicator is on or the bulb does not work, you may need to have


the vehicle serviced. See On-Board Diagnostics (OBD-II). Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, your vehicle is not ready for I/M testing.


118


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Transmission


AUTOMATIC TRANSMISSION


WARNINGS


Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition


to the off position and remove the key whenever you leave your vehicle.


Do not apply the brake pedal and accelerator pedal simultaneously. Applying both pedals simultaneously


for more than three seconds will limit engine rpm, which may result in difficulty maintaining speed in traffic and could lead to serious injury. Understanding the Positions of Your Automatic Transmission Putting your vehicle in gear: 1. Fully press down the brake pedal. 2. Press and hold the button on the front


of the gearshift lever.


3. Move the gearshift lever into the


desired gear.


4. Release the button and your


transmission will remain in the selected gear.


P (Park) This position locks the transmission and prevents the front wheels from turning. Come to a complete stop before putting your vehicle into and out of P (Park) R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) The normal driving position for the best fuel economy. Transmission operates in gears one through six. S (Sport) Moving the gearshift lever to S (Sport): • Provides additional grade (engine)


braking and extends lower gear operation to enhance performance for uphill climbs, hilly terrain or mountainous areas. This will increase engine RPM during engine braking.


• Provides additional lower gear


operation through the automatic transmission shift strategy.


• Gears are selected more quickly and


at higher engine speeds.


SelectShift Automatic® Transmission (If Equipped) Your SelectShift automatic transmission gives you the ability to manually change gears.


119


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E133124 Transmission


To use SelectShift, move the gearshift lever into S (Sport). Use the +/- buttons on the side of your gearshift lever to manually change gears. • Press the (+) button to upshift. • Press the (-) button to downshift. Note: After you have assumed manual control with SelectShift your vehicle will remain in this mode until you return the gearshift lever from (S) Sport, back to (D) Drive. Upshift to the recommended shift speeds according to the following chart:


Upshifts when accelerating (recom-


mended for best fuel economy)


Shift from:


1 - 2
2 - 3
3 - 4
4 - 5
5 - 6


15 mph (24 km/h) 25 mph (40 km/h) 40 mph (64 km/h) 45 mph (72 km/h) 50 mph (80 km/h)


The instrument cluster will display the selected gear that you are currently in and a shift indicator arrow to assist in optimizing shifting. SelectShift will automatically make some shifts for you in the event that your engine speed is running at too high, or to low an RPM. Note: Engine damage may occur if excessive engine revving is held without shifting. Brake-Shift Interlock WARNINGS


Do not drive your vehicle until you verify that the brake lamps are working.


WARNINGS


When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll


freely. To avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure. Use wheel chocks if appropriate.


If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be


working properly. See your authorized dealer.


Use the brake shift interlock lever to move the gearshift lever from the park position in the event of an electrical malfunction or if your vehicle has a dead battery. Apply the parking brake and turn the ignition off before performing this procedure. 1.


Insert a screwdriver (or similar tool) between the shifter bezel and the top finish panel.


2. Use the tool to unsnap the shifter bezel


from the finish panel.


3. Locate the white lever located on the


left side of the shifter.


4. Using the tool move the white lever


towards the rear of the shifter.


120


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E142627 Transmission


5. While holding the white lever in the rear position, move the shifter from the park position.


6. Press the shifter bezel back into the top


finish panel until it snaps back into position.


7. Apply the brake pedal, start the vehicle


and release the parking brake.


Note: See your authorized dealer as soon as possible if this procedure is used. If Your Vehicle Gets Stuck In Mud or Snow Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Note: Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear.


121


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Brakes


GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out. Have the system checked by an authorized dealer. If your vehicle has continuous vibration or shudder in the steering wheel while braking, have it checked by an authorized dealer. Note: Brake dust may accumulate on the wheels, even under normal driving conditions. Some dust is inevitable as the brakes wear and does not contribute to brake noise. See Cleaning the Alloy Wheels (page 206).


See Warning Lamps and Indicators (page 73).


Wet brakes result in reduced braking efficiency. Gently press the brake pedal a few times when driving from a car wash or standing water to dry the brakes. Brake Over Accelerator In the event the accelerator pedal becomes stuck or entrapped, apply steady and firm pressure to the brake pedal to slow the vehicle and reduce engine power. If you experience this condition, apply the brakes and bring your vehicle to a safe stop. Move the transmission to park (P), switch the engine off and apply the parking brake. Inspect the accelerator pedal for any interference. If none are found and the condition persists, have your vehicle towed to the nearest authorized dealer. Brake Assist Brake assist detects when you brake rapidly by measuring the rate at which you press the brake pedal. It provides maximum braking efficiency as long as you press the pedal, and can reduce stopping distances in critical situations.


Anti-lock Brake System This system helps you maintain steering control during emergency stops by keeping the brakes from locking.


This lamp momentarily illuminates when you turn the ignition on. If the light does not illuminate during start up, remains on or flashes, the system may be disabled. Have the system checked by an authorized dealer. If the anti-lock brake system is disabled, normal braking is still effective.


If the brake warning lamp illuminates when you release the parking brake, have the system


checked by an authorized dealer.


HINTS ON DRIVING WITH ANTI-LOCK BRAKES Note: When the system is operating, the brake pedal will pulse and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal. The anti-lock braking system will not eliminate the risks when: •


You drive too closely to the vehicle in front of you. Your vehicle is hydroplaning. You take corners too fast. The road surface is poor.


• • • PARKING BRAKE


WARNING


Always set the parking brake fully and leave your vehicle with the transmission selector lever in


position P.


122


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E144522E144522 Brakes


Note: Do not press the release button while pulling the lever up. To apply the parking brake: 1. Press the foot brake pedal firmly. 2. Pull the parking brake lever up to its


fullest extent.


Note: If you park your vehicle on a hill and facing uphill, move the transmission selector lever to position P and turn the steering wheel away from the curb. Note: If you park your vehicle on a hill and facing downhill, move the transmission selector lever to P and turn the steering wheel toward the curb. To release the parking brake: 1. Press the brake pedal firmly. 2. Pull the lever up slightly. 3. Press the release button and push the


lever down.


HILL START ASSIST (If Equipped)


WARNINGS


The system does not replace the parking brake. When you leave your vehicle, always apply the parking


brake. Failure to leave your vehicle securely parked may lead to a crash or injury. See Parking Brake (page 122).


You must remain in your vehicle once the system activates. Failure to follow this warning could result in


serious personal injury or death.


During all times, you are responsible for controlling your vehicle, supervising the system and


intervening, if required. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.


WARNINGS


The system will turn off if a malfunction is apparent or if you rev the engine excessively. Failure to


take care may result in the loss of control of your vehicle, serious personal injury or death.


The system makes it easier to pull away when your vehicle is on a slope without the need to use the parking brake. When the system is active, your vehicle will remain stationary on the slope for two to three seconds after you release the brake pedal. This allows time to move your foot from the brake to the accelerator pedal. The brakes are released automatically once the engine has developed sufficient drive to prevent your vehicle from rolling down the slope. This is an advantage when pulling away on a slope, for example from a car park ramp, traffic lights or when reversing uphill into a parking space. The system will turn on automatically on any slope which can result in significant vehicle rollback. Using Hill Start Assist 1. Press the brake pedal to bring your


vehicle to a complete standstill. Keep the brake pedal pressed. If the sensors detect that your vehicle is on a slope, the system will activate automatically.


2.


3. When you remove your foot from the brake pedal, your vehicle will remain on the slope without rolling away for approximately two to three seconds. This hold time will automatically be extended if you are in the process of driving off.


4. Drive off in the normal manner. The


brakes will be released automatically.


123


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Traction Control


System Indicator Lights and Messages


WARNING


If a failure has been detected within the AdvanceTrac system, the stability control light will illuminate


steadily. Verify that the AdvanceTrac system was not manually disabled through the information display. If the stability control light still illuminates steadily, have the system serviced by an authorized dealer immediately. Operating your vehicle with AdvanceTrac disabled could lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.


The stability control light temporarily illuminates on engine start-up and flashes when a driving condition activates the stability system.


The stability control off light temporarily illuminates on engine start-up and stays on


when you turn the traction control system off. When you turn the traction control system off or on, a message appears in the information display showing system status.


PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels spin when accelerating on slippery or loose surfaces, the system reduces engine power in order to increase traction. USING TRACTION CONTROL In certain situations for example, stuck in snow or mud, turning the traction control off may be beneficial as this allows the wheels to spin with full engine power. Depending on the type of system you have on your vehicle, you can either turn the system off using the information display or by pressing the button. Switching the System Off Using the Information Display Controls (If Equipped) Your vehicle comes with this feature already enabled. If required, you can switch this feature off using the information display controls. See General Information (page 77). Switching the System Off Using a Switch (If Equipped) The button is located in the instrument panel. Press the button. You will see a message in conjunction with an illuminated icon in the display. Press the button again to return the system to normal mode. When you switch the traction control system off, stability control remains fully active.


124


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E138639 Stability Control


PRINCIPLE OF OPERATION


WARNINGS


Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel and tire size may change the handling characteristics of your vehicle and may adversely affect the performance of the AdvanceTrac system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac system. Install any aftermarket stereo loudspeaker as far as possible from the front center console, the tunnel, and the front seats in order to minimize the risk of interfering with the AdvanceTrac sensors. Reducing the effectiveness of the AdvanceTrac system could lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.


Remember that even advanced technology cannot defy the laws of physics. It’s always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage. Activation of the AdvanceTrac system is an indication that at least some of the tires have exceeded their ability to grip the road; this could reduce the operator’s ability to control the vehicle potentially resulting in a loss of vehicle control, vehicle rollover, personal injury and death. If your AdvanceTrac system activates, SLOW DOWN.


The AdvanceTrac with Roll Stability Control system helps you keep control of your vehicle when on a slippery surface. The electronic stability control portion of the system helps avoid skids and lateral slides and roll stability control helps avoid a vehicle rollover. The traction control system helps avoid drive wheel spin and loss of traction. See Using Traction Control (page 124).


Vehicle without AdvanceTrac with RSC skidding off its intended route. Vehicle with AdvanceTrac with RSC maintaining control on a slippery surface.


125


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E72903AAABBBB Stability Control


USING STABILITY CONTROL AdvanceTrac® with Roll Stability Control™ (RSC®) The system automatically activates when you start your vehicle. The AdvanceTrac with RSC system cannot be completely turned off, but the electronic stability control and roll stability control portions of the system are disabled when the transmission is in position R. You can turn off the traction control portion of the system independently. See Using Traction Control (page 124).


126


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Parking Aids


PRINCIPLE OF OPERATION


WARNINGS


The system does not relieve you of your responsibility to drive with due care and attention. If your vehicles has a non-Ford approved trailer tow module the system may not correctly detect


objects.


The sensors may not detect objects in heavy rain or other conditions that cause disruptive reflections. The sensors may not detect objects with surfaces that absorb ultrasonic waves. The system does not detect objects that are moving away from your vehicle. They will only be detected shortly after they start to move toward your vehicle.


Take particular care when reversing with a tow ball arm or a rear fitted accessory. For example, a bicycle


carrier. The rear parking aid will only indicate the approximate distance from the rear bumper to an object.


If you use a high pressure spray to wash your vehicle, only spray the sensors briefly from a distance not less than eight inches (20 centimeters).


Note: If your vehicle has a tow ball arm, the system is turned off automatically when trailer lamps (or lighting boards) are connected to the 13-pin socket through a Ford approved trailer tow module. Note: Keep the sensors free from dirt, ice or snow. Do not clean with sharp objects. Note: The system may emit false alerts if it detects a signal using the same frequency as the sensors or if your vehicle is fully loaded.


Note: The outer sensors may detect the side walls of a garage. If the distance between the outer sensors and the side wall remains constant for three seconds, the alert will turn off. As you continue the inner sensors will detect objects directly behind your vehicle. PARKING AID (If Equipped)


WARNINGS


Sensing is only an aid to detect some objects when moving forward or backward at low speeds. Traffic


control systems, inclement weather or an external motor and fan can affect the sensors; this may include reduced performance or false activation. To help avoid personal injury you must read and understand the limitations of the system detailed in this section.


The parking aid system may not prevent contact with small or moving objects that are close to the ground.


The parking aid system gives an audible warning when it detects a large object helping to avoid damage to your vehicle. To help avoid personal injury you must take care when using the parking aid system.


Note: Some add-on equipment can cause reduced performance or false activation. For example, large trailer hitches, bike or surfboard racks. Note: The parking aid system sensors must be kept clean and free from snow or ice to avoid reduced performance or false activation. Do not clean the sensors with sharp objects. Note: If the parking aid sensors are misaligned due to vehicle bumper damage it will cause reduced performance or false activation.


127


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Parking Aids


The parking aid system gives an audible warning and reduces the radio volume when it detects a large object within a limited range of your vehicle’s bumpers. Note: When the parking aid system no longer detects a large object the radio volume will return to the previous level. Rear Sensing System The rear parking aid sensors turn on automatically when you move the transmission selector lever to R (reverse) and your vehicle is moving at a speed of less than 3 mph (5 km/h). Moving your vehicle closer to a large object will increase the audible warning repeat rate. When the object is less than 12 inches (30
centimeters) from the center of your vehicle’s rear bumper the audible warning will sound continuously. If the object is more than 12 inches (30 centimeters) from the side of your vehicle’s rear bumper the audible warning will sound for three seconds. If the object is less than 12 inches (30 centimeters) from the side of your vehicle’s rear bumper the audible warning will sound continuously.


The rear parking aid sensor coverage area is up to 72 inches (183 centimeters) from the center of your vehicle’s rear bumper. There is a decreased coverage area at the outer corners.


The system detects large objects when you move the transmission selector lever to R (reverse): •


and your vehicle is moving toward the object at a speed of less than 3 mph (5 km/h) and your vehicle is not moving but a moving object is approaching the rear of your vehicle at a speed of less than 3 mph (5 km/h) and your vehicle is moving at a speed of less than 3 mph (5 km/h) and a moving object is approaching the rear of your vehicle at a speed of less than 3 mph (5 km/h).




Move the transmission selector lever from R (reverse) or press the parking aid button to switch the system off. If a fault is present in the system, a warning message appears in the information display and does not allow you to switch the system on.


128


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E130178 Parking Aids


Front and Rear Sensing System The front and rear parking aid sensors turn on automatically when you move the transmission selector lever to R (reverse), D (drive) or S (sport) and your vehicle is moving at a speed of less than 7 mph (12
km/h).


The front parking aid sensor coverage area is up to 31 inches (80 centimeters) from the center of your vehicle’s front bumper and up to 14 inches (35
centimeters) to the side of your vehicle’s front bumper. The rear parking aid sensor coverage area is up to 72 inches (183
centimeters) from the center of your vehicle’s rear bumper. There is a decreased coverage area at the outer corners.


Audible warnings will sound when large objects are within the sensor coverage areas of either bumper in the following manner: •


You will hear a high-pitched tone from the front audio system speakers when large objects are within the sensor coverage area of your vehicle’s front bumper. Moving your vehicle closer to a large object will increase the audible warning repeat rate. You will hear a lower-pitched tone from the rear audio system speakers when large objects are within the sensor coverage area of your vehicle’s rear bumper. Moving your vehicle closer to a large object will increase the audible warning repeat rate. The parking aid system prioritizes audible warnings based on large objects that are the closest to your vehicle’s front or rear bumper. For example, if an object is 24 inches (60
centimeters) from your vehicle’s front bumper and at the same time, an object is only 16 inches (40
centimeters) from your vehicle’s rear bumper, you will hear the lower-pitched tone from the rear audio system speakers. You will hear an alternating audible warning from the front and rear audio system speakers if large objects are less than 12 inches (30 centimeters) from your vehicle’s front and rear bumpers. If the object is more than 12 inches (30
centimeters) from the side of your vehicle’s bumper area the audible warning will sound for three seconds. If the object is less than 12 inches (30
centimeters) from the side of your vehicle’s bumper area the audible warning will sound continuously.






129


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E130382A Parking Aids


Move the transmission selector lever from R (reverse), D (drive), S (sport) or move away from large objects as you drive off, or press the parking aid button to switch the system off. If a fault is present in the system, a warning message appears in the information display and does not allow you to switch the system on. REAR VIEW CAMERA (If Equipped)


WARNINGS


The rear view camera system is a reverse aid supplement device that still requires the driver to use it in


conjunction with the interior and exterior mirrors for maximum coverage.


The camera may not detect objects that are very close to your vehicle. Back up as slow as possible since higher speeds might limit your reaction time to stop the vehicle.


Note: The operation of the camera may vary depending on the ambient temperature, vehicle and road conditions.


The camera is on the rear cargo door or liftgate. Switching the Rear View Camera On Switch the ignition and the audio unit on. Move the transmission selector lever to reverse (R). The camera may not operate correctly in the following conditions: • Dark areas. • •


Intense light areas. If there is a sudden change to the ambient temperature. If the camera is wet. If the camera is obstructed.


• • Using the Display


WARNINGS


Objects in the display are closer than they appear. Objects above the camera may not be visible. Check the area behind your vehicle when necessary.


Distance markers are only a guide and are calculated for unloaded vehicles on an even road surface.


130


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E165580E165579 Parking Aids


The lines show a projected vehicle path and the approximate distance from the rear bumper to an object.


Green - Zone Black - center line of the projected vehicle path


Note: When reversing with a trailer the camera will show the direction of your vehicle and not the direction of the trailer. Note: When reversing with a trailer the screen does not display the lines. Switching the Rear View Camera Off The image does not display when you move the gearshift lever into Park (P). Vehicles With Rear View Camera Delay To turn this feature on See Settings (page 311). The display will automatically switch off after disengaging reverse (R) gear. The system will automatically switch off when your vehicle speed is above 5.0 mph (8 km/h). Note: Depending upon which type of multimedia display you have, the rear view camera delay is always on, it cannot be switched off. Vehicles With Parking Aid (If Equipped) The display will show a colored distance bar. This indicates the approximate distance from the rear bumper to an object. These are color coded as follows: • Red - Zone • Amber - Zone • Green - Zone


Red - Zone Amber - Zone


131


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E142132ABCABCD Cruise Control (If Equipped)


PRINCIPLE OF OPERATION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h). USING CRUISE CONTROL


WARNINGS


Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could


result in loss of vehicle control, serious injury or death.


When you are going downhill, your vehicle speed may increase above the set speed. The system will not apply the brakes. Change down a gear to assist the system in maintaining the set speed. Failure to do so could result in loss of vehicle control, serious injury or death.


Note: Cruise control will disengage if your vehicle speed decreases more than 10 mph (16 km/h) below your set speed while driving uphill.


Switching Cruise Control On Press and release ON.


The indicator will display in the instrument cluster.


Setting a Speed 1. Accelerate to the desired speed. 2. Press and release SET+. 3. Take your foot off the accelerator


pedal.


Changing the Set Speed • Press and hold SET+ or SET-. Release the control when you reach the desired speed.


• Press and release SET+ or SET-. The set speed will change in approximately 1 mph (2 km/h) increments.


• Press the accelerator or brake pedal


until you reach the desired speed. Press and release SET+.


Canceling the Set Speed Pull CAN toward you and release, or tap the brake pedal. The system will not erase the set speed. Resuming the Set Speed Pull RES toward you and release. Switching Cruise Control Off Note: You will erase the set speed if you switch the system off. Press and release OFF or switch the ignition off.


The cruise control switches are located on the steering wheel.


132


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E142437E71340 Driving Aids


system. If this should occur, you will neither lose the ability to steer your vehicle manually nor will it cause permanent damage. Typical steering and driving maneuvers allows the system to cool and steering assist to return to normal. Steering Tips If the steering wanders or pulls, check for: • An improperly inflated tire. • Uneven tire wear. •


Loose or worn suspension components. Loose or worn steering components. Improper vehicle alignment.


• • A high crown in the road or high crosswinds may also make the steering seem to wander or pull. Adaptive Learning The electronic power steering system adaptive learning helps correct road irregularities and improves overall handling and steering feel. It communicates with the brake system to help operate advanced stability control and accident avoidance systems. Additionally, whenever the battery is disconnected or a new battery installed, you must drive your vehicle a short distance before the system relearns the strategy and reactivates all systems.


STEERING Electric Power Steering WARNINGS


The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation. When a system error is detected a steering message will appear in the information display.


The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation of the electronic system. When an electronic error is detected, a message will be displayed in the information display. If this happens, stop the vehicle in a safe place, and turn off the engine. After at least 10 seconds, reset the system by restarting the engine, and watch the information display for a steering message. If a steering message returns, or returns while driving, take the vehicle to your dealer to have it checked. Obtain immediate service if a system error is detected. You may not notice any difference in the feel of your


steering, but a serious condition may exist. Failure to do so may result in loss of steering control.


Your vehicle has an electric power steering system. There is no fluid reservoir to check or fill. If your vehicle loses electrical power while you are driving (or if you switch the ignition off), you can steer your vehicle manually, but it takes more effort. Extreme continuous steering may increase the effort it takes for you to steer. This occurs to prevent internal overheating and permanent damage to your steering


133


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Load Carrying


LUGGAGE ANCHOR POINTS


Adjustable Load Floor (If Equipped)


Vehicles with the standard size spare tire can adjust the load floor to two positions. The front of the load floor can be placed either on (for high position) or below (for low position) the ledges behind the rear seats. The rear of the load floor always sits on the two small shelves located on the liftgate trim. CARGO NETS (If Equipped) Installing the Net


REAR UNDER FLOOR STORAGE Passenger Compartment Floor


The under floor storage compartment is located behind the front passenger seat.


134


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E167350E78097E142446E1710171122 Load Carrying


1. Push the ends of the upper bar toward


each other and insert them into the retainers in the roof. Push the bar forward into the narrow section of the retainers.


3. Tighten the straps. Removing the Net


2. Attach the net to the luggage anchor points. See Luggage Anchor Points (page 134).


135


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E167370E167371E167372 Load Carrying


1. Release the straps. 2. Remove the net from the luggage


anchor points.


3. Remove the upper bars. ROOF RACKS AND LOAD CARRIERS (If Equipped) WARNINGS


Read and follow the manufacturer’s instructions when you are fitting a roof rack. Failure to take care may


lead to a crash or personal injury.


When loading the roof racks, we recommend you evenly distribute the load, as well as maintain a low


center of gravity. Loaded vehicles, with higher centers of gravity, may handle differently than unloaded vehicles. Take extra precautions, such as slower speeds and increased stopping distance, when driving a heavily loaded vehicle. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.


For correct roof rack system function, you must place loads directly on crossbars fitted to the roof rack side rails. When using the roof rack system, we recommend you use Ford genuine accessory crossbars designed specifically for your vehicle. Make sure that you securely fasten the load. Check the tightness of the load before driving and at each fuel stop. Note: If you use a roof rack, the fuel consumption of your vehicle will be higher and you may experience different driving characteristics. Note: Never place loads directly on the roof panel.


Maximum Load Weights Do not exceed the following maximum roof rack load weights.


Variant


Maximum Load lb


(kg)* 132 (60)


165 (75)


165 (75)


165 (75)


Wagon - short wheel base with panoramic roof panel Wagon - short wheel base with metal roof panel Wagon - long wheel base Van *Evenly distribute the load on the roof rack. LOAD LIMIT Vehicle Loading - with and without a Trailer This section will guide you in the proper loading of your vehicle, trailer or both, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label:


136


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Load Carrying


Base Curb Weight - is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment.


Vehicle Curb Weight - is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment.


Payload - is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload. The payload listed on the Tire Label is the maximum payload for the vehicle as built by the assembly plant. If you install any aftermarket or


authorized-dealer installed equipment on the vehicle, you must subtract the weight of the equipment from the payload listed on the Tire Label in order to determine the new payload.


WARNING


The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.


137


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E143816PAYLOAD Load Carrying


Example only:


138


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E142516E142517E143817CARGO Load Carrying


Cargo Weight - includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) - is the total weight placed on each axle (front and rear) including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) - is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance


Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position. The total load on each axle must never exceed its Gross Axle Weight Rating. Note: For trailer towing information refer to the RV and Trailer Towing Guide available at an authorized dealer.


GVW (Gross Vehicle Weight) - is the Vehicle Curb Weight, plus cargo, plus passengers. GVWR (Gross Vehicle Weight Rating) - is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). It is shown on the


Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position. The Gross Vehicle Weight must never exceed the Gross Vehicle Weight Rating.


139


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E143818GVW Load Carrying


Example only:


WARNING


Exceeding the Safety Compliance Certification


Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.


140


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E142523E142524 Load Carrying


GCW (Gross Combined Weight) - is the Gross Vehicle Weight plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) - is the maximum allowable weight of the vehicle and the loaded trailer, including all cargo and passengers, that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at Gross Vehicle Weight Rating, not at Gross Combined Weight Rating.) Separate functional brakes should be used for safe control of towed vehicles and for trailers where the Gross Combined Weight of the towing vehicle plus the trailer exceed the Gross Vehicle Weight Rating of the towing vehicle. The Gross Combined Weight must never exceed the Gross Combined Weight Rating. Maximum Loaded Trailer Weight - is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with mandatory options, driver and front passenger weight (150 pounds [68 kilograms] each), no cargo weight (internal


or external) and a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer). Consult an authorized dealer (or the RV and Trailer Towing Guide available at an authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight - refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5000 pound (2268 kilogram) conventional trailer, multiply 5000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 pounds (227 to 340 kilograms). For an 11500 pound (5216 kilogram) fifth wheel trailer, multiply by 0.15 and 0.25 to obtain a proper king pin load range of 1725 to 2875 pounds (782 to 1304 kilograms). WARNINGS


Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.


141


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


E143819GCWGVW Load Carrying


WARNINGS


Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GAWR limitations.


Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury.


Steps for determining the correct load limit: 1. Locate the statement "The


combined weight of occupants and cargo should never exceed XXX kg or XXX lb." on your vehicle’s placard.


2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.


3. Subtract the combined weight


of the driver and passengers from XXX kg or XXX lb.


4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400-750 (5 x 150) = 650 lb.)


5. Determine the combined


weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.


6.


The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: *Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You decide to go golfing. Is there enough load capacity to carry you, four of your friends and all the golf bags? You and four friends average 220
pounds (99 kilograms) each and the golf bags weigh approximately 30 pounds (13.5 kilograms) each. The calculation would be: 1400 - (5 x 220) - (5 x 30) = 1400 - 1100


142


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Load Carrying


- 150 = 150 pounds. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635
kilograms - (5 x 99 kilograms) - (5 x 13.5 kilograms) = 635 - 495 - 67.5 = 72.5 kilograms. *Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past two years. Measuring the inside of the vehicle with the rear seat folded down, you have room for twelve 100-pound (45-kilogram) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 pounds (99 kilograms), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440
- 1200 = - 240 pounds. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kilograms - (2 x 99
kilograms) - (12 x 45 kilograms) = 635 - 198 - 540 = -103 kilograms. You will need to reduce the load weight by at least 240 pounds (104 kilograms). If you remove three 100-pound (45-kilogram) cement bags, then the load calculation would be:1400 - (2 x 220) - (9 x 100) = 1400 - 440 - 900 = 60 pounds. Now you have


the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kilograms - (2 x 99
kilograms) - (9 x 45 kilograms) = 635 - 198 - 405 = 32 kilograms. The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position. Special Loading Instructions for Owners of Pick-up Trucks and Utility-type Vehicles


WARNING


Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.


Your vehicle can haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling cargo and people may raise the center of gravity of the vehicle.


143


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Towing


TOWING A TRAILER WARNINGS


Do not exceed the GVWR or the GAWR specified on the


certification label.


Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.


The electrical system on your vehicle may have fuses or relays related to the towing equipment. See Fuses (page 166). The load capacity of your vehicle is designated by weight not volume. You will not necessarily be able to use all available space when loading your vehicle or trailer. Towing a trailer places extra load on the engine, transmission, axle, brakes, tires and suspension. Inspect these components before, during and after towing.


Load Placement To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest


to the trailer floor.


• Load the heaviest items


centered between the left and right side trailer tires.


• Load the heaviest items above the trailer axles or just slightly forward toward the trailer tongue. Do not allow the final trailer tongue weight to go above 15% or below 10% of the loaded trailer weight.


• Select a tow bar with the


correct rise or drop. When both the loaded vehicle and trailer are connected, the trailer frame should be level, or slightly angled down toward your vehicle, when viewed from the side. Note: A slight vibration or shudder may be present when you start to drive away due to increased payload weight. Information on correct trailer loading and preparing your vehicle is available in the load carrying section. See Load Limit (page 136). Further information is available in the RV and Trailer Towing Guide. See an authorized dealer.


144


Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013


Towing


Note: Make sure you take the trailer frontal area into consideration, do not exceed 20
feet (1.86 meters). Towing a trailer that exceeds this frontal area will reduce the performance and fuel economy of your vehicle when towing. Select a trailer that has a rounded front and an aerodynamic design. Note: For high altitude operation, reduce the gross combined weight by 2% per 1000 feet (300 meters) starting at the 1000 foot (300
meter) elevation point. Note: Certain states require electric trailer brakes for trailers over a specified weight. Be sure to check state regulations for this specified weight. The maximum loaded trailer weights listed may be limited to this specified weight, as the vehicle’s electrical system may not include the wiring connector needed to activate electric trailer brakes.


Trailer Lighting The electrical system on your vehicle is not suitable for towing trailers with LED lamps. TRAILER SWAY CONTROL If the trailer begins to sway, the stability control warning lamp flashes and a message appears in the information display. The system applies the brakes to the individual wheels and reduces engine torque to aid vehicle stability. Stop your vehicle as soon as it is safe to do so. Check the vertical weight on the tow ball and trailer load distribution. See Capacities and Specifications (page 237). See Load Carrying (page 134). Note: This feature does not prevent trailer sway, but reduces it once it begins. Note: This feature cannot stop all trailers from swaying. Note: In some cases, if your vehicle speed is too high, the system may turn on multiple times, gradually reducing your vehicle speed. RECOMMENDED TOWING WEIGHTS Your vehicle may tow a trailer. The maximum loaded trailer weight must be less than or equal to the maximum loaded trailer weight listed for your vehicle configuration on the following chart.

Loading...
x