2014 Ford Transit Connect Owners Manual

result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury. Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

The driver and front passenger airbags will deploy during significant frontal and near frontal crashes. The driver and passenger front airbag system consists of: • Driver and passenger airbag modules. •

Front passenger sensing system.

· Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 39).

Proper Driver and Front Passenger Seating Adjustment WARNING

National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance

of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module.

To properly position yourself away from the airbag: • Move your seat to the rear as far as you

can while still reaching the pedals comfortably.

• Recline the seat slightly (one or two degrees) from the upright position. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. Children and Airbags WARNING

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

34

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E151127Supplementary Restraints System

WARNINGS

To reduce the risk of possible serious injury: Do not stow objects in seatback map pocket or hang

objects off seatback if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console. Check the passenger airbag indicator lamp for proper airbag status. Failure to follow these instructions may interfere with the front passenger seat sensing system.

Any alteration or modification to the front passenger seat may affect the performance of the front passenger

sensing system.

This system works with sensors that are part of the front passenger seat and safety belt to detect the presence of a properly-seated occupant and determine if the front passenger frontal airbag should be enabled (may inflate) or not.

The front passenger sensing system uses a passenger airbag indicator which will illuminate indicating that the front passenger frontal airbag is either ON (enabled) or OFF (disabled). The indicator lamp is located at the top center of the instrument panel. Note: When the ignition is first tuned on, the indicator lamps will illuminate for a short period of time to confirm it is functional.

Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a crash. FRONT PASSENGER SENSING SYSTEM

WARNINGS

Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a

rear seating position. Failure to follow this could seriously increase the risk of injury or death.

Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat

cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash.

35

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E142846E170286Supplementary Restraints System

The front passenger sensing system is designed to disable (will not inflate) the front passenger frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology, parents are strongly encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag when the passenger seat is empty. • When the front passenger sensing

system disables (will not inflate) the front passenger frontal airbag, the OFF indicator lamp will illuminate and stay illuminated to remind you that the front passenger frontal airbag is disabled. If the child restraint has been installed and the passenger airbag status indicator illuminates the ON lamp, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer's instructions.

•

The front passenger sensing system is designed to enable (may inflate) the front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.

• When the front passenger sensing

system enables the front passenger frontal airbag (may inflate), the ON indicator lamp will be unlit and stay unlit.

If a person of adult size is sitting in the front passenger seat, but the airbag OFF indicator lamp is illuminated, it is possible that the person is not sitting properly in the seat. If this happens: •

Turn the vehicle off and ask the person to place the seatback in the full upright position.

• Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended.

• Restart the vehicle and have the person

remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger frontal airbag. If the OFF indicator lamp remains illuminated even after this, the person should be advised to ride in the rear seat.

•

Occupant

Empty

Child

Adult

Passenger airbag OFF indic-

ator

Passenger airbag

Disabled

Disabled

Enabled

OFF: Lit ON: Unlit OFF: Lit ON: Unlit OFF: Unlit

ON: Lit

36

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Supplementary Restraints System

If the airbag readiness light is illuminated, do the following: The driver and adult passengers should check for objects lodged underneath the front passenger seat, or cargo interfering with the seat. If there are lodged objects, or cargo is interfering with the seat, take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver and adult passengers should

check for any objects lodged underneath the front passenger seat or cargo interfering with the seat.

• Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least two minutes and verify that the airbag readiness light is no longer illuminated. If the airbag readiness light remains illuminated, this may or may not be a problem due to the front passenger sensing system.

•

Do not attempt to repair or service the system. Take your vehicle immediately to an authorized dealer. If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center. See Getting the Services You Need (page 160).

Note: When the passenger airbag OFF light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbag deployment injuries. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • Objects lodged underneath the seat. • Objects between the seat cushion and

the center console.

• Objects hanging off the seatback. • Objects stowed in the seatback map

pocket.

• Objects placed on the occupant's lap. • Cargo interference with the seat. • Other passengers pushing or pulling on

the seat.

• Rear passenger feet and knees resting

or pushing on the seat.

The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above.

Make sure the front passenger sensing system is operating properly. See Crash Sensors

and Airbag Indicator (page 39).

37

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Supplementary Restraints System

SAFETY CANOPY™ WARNINGS

Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying curtain airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not lean your head on the door. The curtain airbag could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the curtain airbags, its fuses, the A, B, C, or D pillar trim, or the

headliner on a vehicle containing curtain airbags as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

To reduce risk of injury, do not obstruct or place objects in the deployment path of the curtain

airbag.

If the curtain airbags have deployed, the curtain airbags will not function again. The curtain airbags (including the A, B, C and D pillar trim and headliner) must be inspected and serviced by an authorized dealer. If the curtain airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The Safety Canopy will deploy during significant side crashes or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopy is mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. In certain sideways crashes or rollover events, the Safety Canopy will be activated, regardless of which seats are occupied. The Safety Canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact crashes and rollover events.

The system consists of the following: •

Safety canopy curtain airbags located above the trim panels over the front and rear side windows identified by a label or wording on the headliner or coat hook.

• A flexible headliner which opens above

the side doors to allow air curtain deployment

•

The crash sensors and monitoring system have a readiness indicator. See Crash Sensors and Airbag Indicator (page 39).

38

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E75004Supplementary Restraints System

Children 12 years old and under should always be properly restrained in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The design and development of the Safety Canopy included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy). CRASH SENSORS AND AIRBAG INDICATOR WARNING

Modifying or adding equipment to the front end of your vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of your vehicle.

Your vehicle has a collection of crash and occupant sensors which provide information to the restraints control module which deploys (activates) the front safety belt pretensioners, driver airbag, passenger airbag, seat mounted side airbags, and the Safety Canopy. Based on the type of accident (frontal impact, side impact or rollover) the restraints control module will deploy the appropriate safety devices.

The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. A warning indicator light in the instrument cluster indicates the readiness of the safety system. If this warning indicator light is not functioning and there is another fault within the system, the message cluster may display an airbag failure warning. See Information Displays (page 77). You will hear five tones that repeat periodically until you repair the problem, the warning indicator light or both. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following:

•

•

The readiness light will not illuminate immediately after the ignition is turned on. The readiness light will either flash or stay lit.

• A series of five beeps will be heard. The

tone pattern will repeat periodically until the problem, the light or both are repaired.

If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash. The safety belt pretensioners and the airbag supplemental restraint system is designed to activate when your vehicle sustains frontal or sideways deceleration sufficient to cause the restraints control module to deploy a safety device or when a certain likelihood of a rollover event is detected by the rollover sensor.

39

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Supplementary Restraints System

The fact that the safety belt pretensioners or airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (for example, crash severity, belt usage) were not appropriate to activate these safety devices. •

The design of the front airbags is to activate only in frontal and near-frontal crashes (not rollovers, side impacts or rear impacts) unless the crash causes sufficient frontal deceleration. The design of the safety belt pretensioners is to activate in frontal, near-frontal and side crashes, and in rollovers. The design of the side airbags is to inflate in certain side impact crashes. Side airbags may activate in other types of crashes if your vehicle experiences sufficient sideways motion or deformation. The design of the Safety Canopy is to inflate in certain side impact crashes or rollover events. The Safety Canopy may activate in other types of crashes if your vehicle experiences sufficient sideways motion or deformation, or a certain likelihood of rollover.

•

•

•

AIRBAG DISPOSAL Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.

40

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Keys and Remote Controls

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. The typical operating range for your transmitter is approximately 33 feet (10
meters). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range: • weather conditions nearby radio towers • structures around the vehicle • other vehicles parked next to your • vehicle

The radio frequency used by your remote control can also be used by other short distance radio transmissions, for example amateur radios, medical equipment, wireless headphones, remote controls and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key. Note: Make sure to lock your vehicle before leaving it unattended. Note: If you are in range, the remote control will operate if you press any button unintentionally.

REMOTE CONTROL Integrated Keyhead Transmitter (If Equipped)

Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control.

Note: Your vehicle’s keys came with a security label that provides important vehicle key cut information. Keep the label in a safe place for future reference. Programming a New Remote Control See an authorized dealer. Reprogramming the Unlocking Function Note: When you press the unlock button only the driver and passenger doors are unlocked. Pressing the unlock button again unlocks all the doors.

41

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E142585E138615Keys and Remote Controls

Press and hold the unlock and lock buttons on the remote control simultaneously for at least four seconds with the ignition off. The direction indicators will flash twice to confirm the change. To return to the original unlocking function, repeat the process. Replacing the Battery The remote control uses one coin type three volt lithium battery CR2032 or equivalent. Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally. Integrated Keyhead Transmitter

1. Twist a thin coin in the slot of the

transmitter near the key ring to remove the battery cover.

2. Remove the old battery.

3.

Insert the new battery. Refer to the instructions inside the transmitter for the correct orientation of the battery. Press the battery down to make sure it is fully in the housing.

4. Snap the battery cover back onto the

transmitter.

Car Finder Press the lock button on the key twice within three seconds. The horn sounds and the direction indicators will flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm. Note: If locking was not successful or if any door or the liftgate is open, or if the hood is open on vehicles with a perimeter alarm or remote start, the horn will sound and the direction indicators will not flash. REPLACING A LOST KEY OR REMOTE CONTROL You can purchase replacement keys or remote controls from an authorized dealer. Authorized dealers can program remote controls for your vehicle. See Remote Control (page 41). To re-program the passive anti-theft system see an authorized dealer.

42

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E138619E138620MyKey™ (If Equipped)

PRINCIPLE OF OPERATION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys can be activated with these restricted modes. Any keys that remain unprogrammed are referred to as administrator keys or admin keys. They can be used to: • Create a MyKey • Program configurable MyKey settings • Clear all MyKey features. When you have created a MyKey, you can access the following information by using the information display to determine: • How many admin keys and MyKeys are

programmed to your vehicle. The total distance your vehicle traveled with a MyKey.

Note: Switch the ignition on to use the system. Note: All MyKeys are programmed to the same settings. You cannot program them individually. Non-configurable Settings The following settings cannot be changed by an admin key user: •

Belt-Minder. You cannot disable this feature. The audio system will mute when the front seat passengers’ safety belts are not fastened. Early low fuel. The low-fuel warning activates earlier, giving the MyKey user more time to refuel.

•

•

• Driver assist features, if equipped on

your vehicle, are forced on: parking aid and Blind Spot Information System (BLIS) with cross traffic alert. Satellite radio adult content restrictions.

•

Configurable Settings With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the engine. You can also change the settings afterward with an admin key. • A vehicle speed limit can be set.

Warnings will be shown in the display followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal or by setting cruise control.

• Various vehicle speed minders can be set. Once you select a speed, it will be shown in the display, followed by an audible tone when the preselected vehicle speed is exceeded.

• Audio system maximum volume of

45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled.

• Always on setting. When this is

selected, you will not be able to turn off Advance Trac, 911 Assist or the do not disturb feature (if your vehicle is equipped with these features).

CREATING A MYKEY You can program a MyKey using the information display control on the steering wheel. See Information Displays (page 77). Insert the key you want to program into the ignition and switch the ignition on.

43

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

MyKey™ (If Equipped)

Press the left arrow button to access the main menu and scroll to:

Message

Settings MyKey Create MyKey

Action and Description

Press the OK button. Press the OK button. When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at your vehicle's next start. Make sure you label the key so you can distinguish it from the admin keys. You can also program configurable settings for the key(s). Refer to the following Programming/Changing Configur- able Settings.

Programming/Changing Configurable Settings Switch the ignition on using an admin key or fob. Use the information display to access the configurable MyKey settings, scroll to:

Message

Action and Description

Settings MyKey

Press the OK button. Use the up and down arrow buttons to scroll to a configurable feature. Press the OK or right arrow button to make a selection. Choose your applicable setting.

Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you switch the ignition off you will need an admin key to change or clear your MyKey settings.

CLEARING ALL MYKEYS You can clear or change your MyKey settings using the information display control on the steering wheel. See Information Displays (page 77).

Switch the ignition on using an admin key or fob.

44

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

MyKey™ (If Equipped)

To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scroll to:

Message

Action and Description

Settings MyKey Clear MyKey

Press the OK button. Press the OK button. Press and hold the OK button until the following message displays.

All MyKeys Cleared Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.

45

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

MyKey™ (If Equipped)

CHECKING MYKEY SYSTEM STATUS

You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 77).

To find information on a programed MyKey(s), press the left arrow button to access the main menu and scroll to:

Message

Description

Settings MyKey Select one of the following: MyKey Dist.

Press the OK button. Press the OK button.

Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear your MyKey. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey. Indicates the number of MyKeys programed to your vehicle. Use this feature to detect how many MyKeys you have for your vehicle and determine when a MyKey has been deleted. Indicates how many admin keys are programed to your vehicle. Use this feature to determine how many unrestricted keys you have for your vehicle, and detect if an additional MyKey has been programed.

{0} MyKeys

{0} Admin Keys

46

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

MyKey™ (If Equipped)

USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non MYKEY TROUBLESHOOTING

Condition I cannot program a MyKey.

I cannot program the configurable settings.

I cannot clear the MyKeys.

I lost the only admin key.

I lost a key.

MyKey distance does not accumulate.

Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system.

Potential Causes

· The key used to start your vehicle does not have admin privileges. · The key used to start your vehicle is the only admin key (there always has to be at least one admin key). · SecuriLock passive anti-theft system is disabled or in unlimited mode. · The key used to start your vehicle does not have admin privileges. · No keys are programmed to the vehicle. See Creating a MyKey (page 43). · The key used to start your vehicle does not have admin privileges. · No MyKeys are programmed to the vehicle. See Creating a MyKey (page 43). Purchase a new key from your authorized dealer. Program a spare key. See Passive Anti- Theft System (page 53). · The MyKey user is not using the MyKey. · An admin key holder cleared the MyKeys and created new MyKeys. · The key system has been reset.

47

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Locks

LOCKING AND UNLOCKING Remote Control The remote control can be used any time your vehicle is not running. Unlocking the Doors The positions lamps illuminate when you unlock the doors. They automatically turn off when you switch the ignition on. Note: You can unlock the driver door with the key. Use the key when the remote control is not functioning. Note: When you lock your vehicle for several weeks, the remote control will be switched off. Your vehicle must be unlocked and the engine started using the key. Unlocking and starting your vehicle once will enable the remote control. One-Stage Unlocking

Press the button to unlock all doors.

The direction indicators will flash. Two-Stage Unlocking

Press the button twice within three seconds to unlock all doors.

The direction indicators flash twice. Reprogramming the Unlocking Function You can reprogram the unlocking function using the remote control to change between one-stage and two-stage unlocking. See Remote Control (page 41).

Locking the Doors

Press the button to lock all the doors. Press the button twice within three seconds to double lock the doors. The horn will chirp twice if all the doors and the luggage compartment are closed. Note: If any door or the luggage compartment is not closed, or if the hood is not closed on vehicles that have an anti-theft alarm or remote start, the horn will not chirp. Automatic Re-locking The doors will relock automatically if you do not open a door within 45 seconds of unlocking the doors with the remote control. The door locks and the alarm will return to their previous state. Locking and Unlocking the Doors From Inside The power door lock control is located on the driver and passenger doors.

Press the button to lock or unlock all the doors. The lamp illuminates with the doors

locked. Opening the Double Rear Doors

WARNING

If there is a ladder fitted to the rear cargo door, do not open the door fully if the side-loading door is open.

48

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E102566Locks

Locking and Unlocking the Doors with the Key Note: Do not leave your keys in your vehicle. Locking with the Key Turn the top of the key toward the front of your vehicle. Unlocking with the Key Turn the top of the key toward the rear of your vehicle. Unlocking the Doors with the Interior Door Handles You can unlock individual doors by pulling the relevant interior door handle. Pulling the driver door interior door handle will unlock all the doors, if auto unlock has been enabled. Rear Door Unlocking and Opening Pull the interior door release handle twice to unlock and open the rear door. The first pull unlocks the door and the second pull will unlatch the door. Smart Unlocks For Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition. When you open one of the front doors and lock your vehicle with the power door lock control, all the doors will lock then unlock if your key is still in the ignition. You can still lock your vehicle with the key in the ignition by pressing the lock button on the transmitter even if the doors are not closed. If both front doors are closed you can lock your vehicle by any method, regardless of whether the key is in the ignition or not.

1. Open the rear cargo door.

2. Press the button. 3. Open the cargo door fully.

49

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E148805E148806E1890912Locks

Smart Unlocks For Intelligent Access Keys (If Equipped) This feature helps to prevent you from unintentionally locking your intelligent access key inside your vehicle’s passenger compartment or rear cargo area. When you lock your vehicle using the power door lock control (with the door open, vehicle in park and ignition off), your vehicle will search for an intelligent access key in the passenger compartment after you close the door. If your vehicle finds a key, all of the doors will immediately unlock and the horn will chirp, indicating that a key is inside. In order to override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle, you can lock your vehicle after all doors are closed by pressing the lock button on another intelligent access key or touching the locking area on the handle with another intelligent access key in your hand. When you open one of the front doors and lock your vehicle using the power door lock control, all doors will lock then unlock if, the ignition is on, or the ignition is off and the gearshift lever is not in park P. Auto lock and Auto unlock Feature Auto lock The Auto lock feature will lock the doors and liftgate when all of the following conditions have been met: • All doors are closed. • •

The ignition is on. Your vehicle is moving at a speed greater than 12 mph (20 km/h) for more than two seconds.

Auto unlock The auto unlock feature will unlock all the doors when all of the following conditions have been met: •

The ignition is on, all doors are closed, and your vehicle is moving at a speed greater than 12 mph (20 km/h) for more than two seconds. Your vehicle has come to a stop and you switch the ignition off or to the accessory position. The driver door is opened within 10
minutes of you switching the ignition off or to the accessory position.

•

•

Note: The doors will not auto unlock if your vehicle has been electronically locked after the ignition is turned off and before the driver door is opened. Enabling or Disabling Auto lock and Auto unlock Note: An authorized dealer or you can carry out this procedure. To enable or disable these features, do the following: 1. Switch the ignition on. 2. Press the power door unlock button

three times.

3. Switch the ignition off. 4. Press the power door unlock button

three times.

5. Switch the ignition on. The horn will

chirp indicating your vehicle is in programming mode.

Auto lock: Press the power door lock button for less than one second and release. The horn will chirp once if disabled or twice (one short and one long chirp) if enabled.

50

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Locks

Auto unlock: Press the power door lock button for longer than two seconds and release. The horn will chirp once if disabled or twice (one short and one long chirp) if enabled. After programming the feature, switch the ignition off. The horn will chirp once indicating programming is complete. Note: You will have 30 seconds to complete the procedure. Note: You can enable or disable the auto unlock feature independently of the auto lock feature. Emergency Locking with the Key Note: If the child safety locks are on and you pull the interior handle, you will only turn off the emergency locking not the child safety lock. You can only open the doors using the external door handle. Note: If the doors have been unlocked using this method, the doors must be locked individually until the central locking function has been repaired. Note: When the central locking function fails to operate, lock the doors individually using the key in the position shown.

Left-Hand Side Turn clockwise to lock. Right-Hand Side Turn counterclockwise to lock. Rear Emergency Exit (If Equipped)

Slide the release lever up to open the door in an emergency.

51

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E112203E180300Locks

MANUAL LIFTGATE (If Equipped)

WARNINGS

It is extremely dangerous to ride in a cargo area, inside or outside of your vehicle. In a crash, people riding in

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Make sure everyone in your vehicle is in a seat and properly using a safety belt. Failure to follow this warning could result in serious personal injury or death.

Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not hang anything from the spoiler, rear window or liftgate, for example a bike rack. This could damage the liftgate and its components. Opening and Closing the Liftgate To Open the Liftgate

2. Press the button located in the top of the liftgate pull cup handle to unlatch the liftgate, then pull on the outside handle.

Note: Do not leave the liftgate open while driving. To Close the Liftgate

1. Press the unlock button, or the tailgate

unlock button on the remote key.

52

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E138632E148833Security

PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting problems if they are too close to the key when starting the engine. Prevent these objects from touching the coded key while starting the engine. Switch the ignition off, move all objects on the key chain away from the coded key and restart the engine if a problem occurs. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle. SecuriLock® The system is an engine immobilization system. It is designed to help prevent the engine from being started unless a correctly coded key for your vehicle is used. Using an incorrectly coded key may prevent the engine from starting. A message may appear in the information display. If you are unable to start the engine with a correctly coded key, a malfunction has happened and a message may appear in the information display. Automatic Arming The engine immobilization system arms immediately after you switch the ignition off.

Automatic Disarming Switching the ignition on with a correctly coded key disarms the engine immobilization system. Replacement Keys The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control. If your keys are lost or stolen and you do not have a spare correctly coded key, you will need to have your vehicle towed to an authorized dealer. You need to erase the coded keys from your vehicle and program new coded keys. Store an extra correctly coded key away from the vehicle in a safe place to help prevent any inconveniences. See an authorized dealer to purchase additional spare or replacement keys. Note: Your vehicle comes with two integrated keyhead transmitters. Programming a Spare Integrated Keyhead Transmitter You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry portion of the remote control to your vehicle Only use integrated keyhead transmitters or standard SecuriLock keys. You must have two previously programmed correctly coded keys and the new unprogrammed key readily accessible. See an authorized dealer to have the spare key programmed if two previously programmed correctly coded keys are not available. Read and understand the entire procedure before you begin.

53

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Security

1.

Insert the first previously programmed correctly coded key into the ignition.

2. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds. 3. Switch the ignition off and remove the

first correctly coded key from the ignition.

4. After three seconds but within 10

seconds of switching the ignition off, insert the second previously correctly coded key into the ignition.

5. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds. 6. Switch the ignition off and remove the

second previously programmed correctly coded key from the ignition.

7. After three seconds but within 10

seconds of switching the ignition off and removing the previously programmed correctly coded key, insert the new unprogrammed key into the ignition.

8. Switch the ignition from off to on. Keep the ignition on for at least six seconds.

9. Remove the newly programmed

correctly coded key from the ignition.

If the key has been successfully programmed it will start the engine and operate the remote entry system (if the new key is an integrated keyhead transmitter). If the key was not successfully programmed, wait 10 seconds and repeat Steps 1 through 8. If you are still unsuccessful, take your vehicle to an authorized dealer. Note: You can program a maximum of eight coded keys to your vehicle. All eight can be integrated keyhead transmitters.

ANTI-THEFT ALARM (If Equipped) Alarm System The perimeter alarm is a deterrent against unauthorized access to your vehicle through the doors, luggage compartment and the hood. It also protects the audio unit. Triggering the Alarm Once armed, the alarm is triggered in any of the following ways: •

If someone opens a door, luggage compartment or the hood without a valid key or remote control. If someone removes the audio or navigation system. If you switch the ignition on without a valid key.

•

•

If the alarm is triggered, the horn will sound for 30 seconds and the hazard warning flasher will flash for five minutes. Any further attempts to perform one of the above will trigger the alarm again. Arming the Alarm To arm the alarm, lock your vehicle. See Locks (page 48). Disarming the Alarm Disarm and silence the alarm by unlocking the doors with the key and switching the ignition on with a correctly coded key within 12 seconds, or by unlocking the doors or the luggage compartment with the remote control.

54

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

Steering Wheel

ADJUSTING THE STEERING WHEEL

WARNING

Do not adjust the steering wheel when your vehicle is moving.

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 96).

3. Lock the steering column. AUDIO CONTROL (If Equipped) Select the required source on the audio unit.

1. Unlock the steering column. 2. Adjust the steering wheel to the desired

position.

55

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

122E951783E95179Steering Wheel

You can operate the following functions with the control:

VOICE CONTROL (If Equipped)

Volume up Seek up, next or end call Volume down Seek down, previous or accept call

Press the button to select or deselect voice control. See SYNC™ (page 258). CRUISE CONTROL (If Equipped)

Seek, Next or Previous Press the seek button to: •

tune the radio to the next or previous stored preset play the next or the previous track.

• Press and hold the seek button to: •

tune the radio to the next station up or down the frequency band seek through a track.

•

See Cruise Control (page 132).

56

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E159789ABCDE159531E142437Steering Wheel

INFORMATION DISPLAY CONTROL

See Information Displays (page 77).

57

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E130248Wipers and Washers

WINDSHIELD WIPERS Note: Fully defrost the windshield before you switch the windshield wipers on. Note: Make sure you switch the windshield wipers and ignition off before using an automatic car wash. Note: If streaks or smears appear on the windshield, clean the windshield and the wiper blades. If that does not resolve the issue, install new wiper blades. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

Single wipe Intermittent wipe Normal wipe High speed wipe

Intermittent Wipe

Short wipe interval Intermittent wipe Long wipe interval

Use the rotary control to adjust the intermittent wipe interval. Speed Dependent Wipers (If Equipped) When your vehicle speed increases, the interval between wipes decreases. AUTOWIPERS (If Equipped) Note: Fully defrost the windshield before you switch the windshield wipers on. Note: Make sure you switch the windshield wipers and ignition off before using an automatic car wash. Note: If streaks or smears appear on the windshield, clean the windshield and the wiper blades. If that does not resolve the issue, install new wiper blades. Note: If you switch autolamps and autowipers on, the headlamps will automatically turn on when the windshield wipers continuously operate.

58

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

DCABE167118E167119CABWipers and Washers

Keep the outside of the windshield clean. The rain sensor is very sensitive and the wipers may operate if dirt, mist or insects hit the windshield. WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat. Note: Do not operate the washers for more than 10 seconds at a time.

To use the washer, pull the lever toward you. When you release the lever, wiping will continue for a short period of time. REAR WINDOW WIPER AND WASHERS (If Equipped) Rear Window Wiper Note: Make sure you switch the rear window wiper and ignition off before using an automatic car wash.

Note: During wet or winter driving conditions with ice, snow or a salty road mist, inconsistent or unexpected wiping or smearing may occur. In these conditions, you can do the following: •

Lower the sensitivity of the autowipers to reduce the amount of smearing on the windshield. Switch to normal or high-speed wipe. Switch autowipers off.

• •

High sensitivity On Low sensitivity

Autowipers uses a rain sensor located in the area around the interior mirror. The rain sensor monitors the amount of moisture on the windshield and automatically turns the wipers on. It will adjust the wiper speed by the amount of moisture that the sensor detects on the windshield. Use the rotary control to adjust the sensitivity of the autowipers. When you select low sensitivity, the wipers will operate when the sensor detects a large amount of water on the windshield. When you select high sensitivity, the wipers will operate when the sensor detects a small amount of water on the windshield.

59

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E167119CABE129188Wipers and Washers

Intermittent wipe. Low speed wipe. Off.

Press the top of the button to switch intermittent wipe on. Press the top of the button again to switch low speed wipe on. Press the bottom of the button to switch the rear window wiper off. When you switch on the front wipers and move the gearshift lever to reverse (R), rear intermittent wipe automatically turns on. Rear Window Washer

Push the lever away from you to operate the rear window washer. When you release the lever, wiping continues for a short period of time.

60

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

ABCE171615E167407Lighting

GENERAL INFORMATION Condensation in Lamp Assemblies Exterior lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. Examples of acceptable condensation are: • The presence of a fine mist (no streaks, drip marks or large droplets).

• A fine mist covers less than 50% of the

lens.

Examples of unacceptable condensation are: • A water puddle inside the lamp. •

Streaks, drip marks or large droplets present on the interior of the lens.

If you see any unacceptable condensation, have your vehicle checked by an authorized dealer.

LIGHTING CONTROL

Off Parking lamps, instrument panel lamps, license plate lamps and tail lamps Headlamps

Parking Lamps (If Equipped) Note: Prolonged use of the parking lamps will cause the battery to run out of charge. Switch the ignition off. Both Sides Set the lighting control to position B.

61

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E142449Lighting

One Side

Headlamp Flasher

Right-hand side Left-hand side

High Beams

Pull the lever toward you slightly and release it to flash the headlamps.

AUTOLAMPS (If Equipped)

Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off.

The headlamps will switch on and off automatically in low light situations or during inclement weather. The headlamps will remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps will remain on. See Information Displays (page 77).

62

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E163717ABE162679E162680E142451Lighting

When the headlamp switch is in the Autolamps position, the windshield wiper activated exterior lamps will turn on within 10 seconds when you switch the windshield wipers on. The exterior lamps will turn off approximately 60 seconds after you switch the windshield wipers off. This feature does not turn on the exterior lamps: • • while the wipers are on to clear washer

during a mist wipe

•

fluid during a wash condition if the wipers are in automatic or intermittent modes.

Note: If you have autolamps and autowipers switched on the low beam headlamps will turn on automatically when the windshield wipers operate continuously. Note: You may have to manually switch the headlamps on in severe weather conditions. Note: If you have autolamps switched on you can only switch the high beam headlamps on once the system has turned the headlamps on. INSTRUMENT LIGHTING DIMMER

Press it repeatedly or press it and hold it until the desired level is reached. Note: If you disconnect the battery or it loses charge the instrument lighting will return to its brightest setting. HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on. DAYTIME RUNNING LAMPS (If Equipped)

WARNING

Always remember to switch the headlamps on in low light situations or during inclement weather. The system does not turn the headlamps or rear lamps on and may not provide adequate lighting. Failure to switch the headlamps on under these conditions may result in a crash.

The system turns the headlamps on when the outside ambient light level is high. To switch the system on: 1. Switch the ignition on. 2. Turn the lighting control switch to the

off or autolamp position.

Vehicles With Halogen Headlamps The system will turn the low beam headlamps on at a reduced intensity when the outside ambient light level is high.

63

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E132712Lighting

FRONT FOG LAMPS (If Equipped)

Press the button to switch the fog lamps on or off. You can switch the fog lamps on when the lighting control is in any position except off and the high beams are not turned on.

CORNERING LAMPS (If Equipped)

Headlamp beam Cornering lamp beam

The cornering lamps illuminate the inside of a corner when you are turning.

64

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E142453E72898BABALighting

DIRECTION INDICATORS

Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. INTERIOR LAMPS - VEHICLES WITHOUT: PANORAMIC ROOF PANEL Courtesy Lamp

Off Door contact On

If you set the switch to position B, the courtesy lamp will switch on when you unlock your vehicle, open a door or the liftgate. If you leave a door open with the ignition switched off, the courtesy lamp will switch off automatically after a short period of time to prevent your vehicle battery from losing charge. To switch it back on, switch the ignition on for a short period of time. The courtesy lamp will also switch on when you switch the ignition off. It will switch off automatically after a short period of time or when you start the engine. If you set the switch to position C with the ignition switched off, the courtesy lamp will switch on. It will switch off automatically after a short period of time to prevent your vehicle battery from losing charge. To switch it back on, switch the ignition on for a short period of time. Reading Lamps

If you switch the ignition off, the reading lamps will switch off automatically after a short period of time to prevent your vehicle battery from losing charge. To switch them back on, switch the ignition on for a short period of time. Luggage Compartment Lamp The luggage compartment lamp will switch on and off automatically when you open and close the doors. If you unlock the doors with the remote control, they will switch on. They will switch off automatically after a short period of time.

65

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E162681E112207BCAE112208Lighting

INTERIOR LAMPS - VEHICLES WITH: PANORAMIC ROOF PANEL Side Mounted Lamp

Center Mounted Lamp

Reading lamp on and off switch Door function switch All lamps on and off switch

Press switch B to turn all lamps off when a door is open. Press the switch again to turn all lamps on. You can control all lamps using switch C.

Right-hand side reading lamp on and off switch Left-hand side reading lamp on and off switch Door function switch All lamps on and off switch

Press switch C to turn all lamps off when a door is open. Press the switch again to turn all lamps on. You can control all lamps using switch D. Luggage Compartment Lamp The luggage compartment lamp will switch on and off automatically when you open and close the doors. If you unlock the doors with the remote control, they will switch on. They will switch off automatically after a short period of time.

66

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

BCE139419AE139420CDABWindows and Mirrors

POWER WINDOWS - VEHICLES WITH: ONE-TOUCH DOWN DRIVER WINDOW

WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Accessory Delay (If Equipped) You can use the window switches for several minutes when you switch the ignition off or until you open either front door. POWER WINDOWS - VEHICLES WITH: REAR POWER WINDOWS

WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. Press the switch to open the window. Lift the switch to close the window. One-Touch Down (If Equipped) Press the switch fully and release it. Press again or lift it to stop the window.

Press the control to open the window. Lift the control to close the window. Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise.

67

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E166915E70848Windows and Mirrors

One-Touch Down (If Equipped) Press the control fully and release it. Press again or lift it to stop the window. One-Touch Up (If Equipped) Lift the control fully and release it. Press or lift it again to stop the window. Window Lock

Press the control to lock or unlock the rear window controls. It lights when the rear window controls lock. Bounce-Back (If Equipped) The window stops automatically while closing. It reverses some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care

when closing the windows to avoid personal injury or damage to your vehicle.

Proceed as follows to override this protection feature when there is a resistance, for example in winter: 1. Close the window twice until it reaches

the point of resistance and let it reverse.

2. Close the window a third time to the point of resistance. You disabled the bounce-back feature and you can now close the window manually. The window travels past the point of resistance and you can close it fully. Contact an authorized dealer as soon as possible if the window does not close after the third attempt. Resetting the Bounce-Back Feature

WARNING

The bounce-back feature remains turned off until you reset the memory.

If you have disconnected the battery, you must reset the bounce-back memory separately for each window. 1. Lift and hold the control until the

window is fully closed.

2. Release the control. 3. Lift and hold the control again for a few

seconds.

4. Release the control. 5. Lift and hold the control again for a few

seconds.

6. Release the control. 7. Press and hold the control until the

window is fully open.

8. Lift and hold the control until the

window is fully closed.

9. Release the control. 10. Open the window and then try to

close it automatically.

68

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E70850Windows and Mirrors

11.

Repeat the procedure if the window does not close automatically.

Accessory Delay (If Equipped) You can use the window controls for several minutes after switching off the ignition or until opening either front door. GLOBAL OPENING AND CLOSING (If Equipped) You can use the remote control to operate the windows with the ignition off. Note: You can enable or disable this feature in the information display or see an authorized dealer. See General Information (page 77). Note: To operate this feature, accessory delay must not be active. Opening the Windows You can only open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows and vent the moonroof. Release the button once movement starts. Press the lock or unlock button to stop movement. Closing the Windows WARNING

When closing the windows and moonroof, you should verify they are free of obstructions and make sure

that children and pets are not in the proximity of the window openings.

To close the windows and moonroof, press and hold the remote control lock button. Release the button once movement starts. Press the lock or unlock button to stop movement.

EXTERIOR MIRRORS Power Exterior Mirrors (If Equipped)

WARNING

Do not adjust the mirrors when your vehicle is moving. This could result in the loss of control of your vehicle,

serious personal injury or death.

Left-hand mirror Off Right-hand mirror

Press the arrows to adjust the mirror. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. Automatic Folding and Unfolding The mirrors will automatically fold or unfold when you use the key to lock or unlock your vehicle.

69

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

ACBE70846E70847Windows and Mirrors

Note: If you fold the mirrors using the manual fold button, you can only unfold them again manually. Manual Folding and Unfolding The power folding mirrors operate with the ignition on, and for several minutes after you switch the ignition off. Note: You can only fold the mirrors when the controller is set to position B. Note: Continuous folding and unfolding of the mirrors will cause them to overheat and shut down for a short time. This is to avoid permanent damage.

Press the down arrow to fold or unfold the mirrors. Press the down arrow again to stop and reverse the direction of movement. Note: Continuous folding and unfolding of the mirrors will cause them to overheat and shut down for a short time. This is to avoid permanent damage. Fold Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position.

INTERIOR MIRROR (If Equipped)

WARNING

Do not adjust the mirror when your vehicle is moving.

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up. SUN SHADES - VEHICLES WITH: PANORAMIC ROOF PANEL (If Equipped)

WARNINGS

Do not let children play with the sun shade or leave them unattended in the vehicle. They may seriously hurt

themselves.

70

Tourneo Connect/Transit Connect (CHC) Canada/United States of America, enUSA, Edition date: 07/2013

E165480Windows and Mirrors

Note: You must start the relearning process within 30 seconds of switching the ignition on. In case the sun shade no longer opens or closes properly, follow this relearning procedure: 1. Press the front of the control to the first action point twice and release it within two seconds.

2. Press the rear of the control to the first action point twice and release it within two seconds.

3. Press and hold the front of the control

to the first action point, until the sun shade fully opens.

4. Press and hold the rear of the control to the first action point, until the sun shade fully closes.

If you do not complete Step 2 within 15
seconds of Step 1, the relearning function end. Switch the ignition off, wait for another 30 seconds and then switch the ignition back on again. Start the procedure again from the beginning. Confirm that relearning was successful by opening and closing the sun shade.

WARNINGS

When closing the sun shade, you should verify that it is free of obstructions and make sure that

children and pets are not in the proximity of the sunshade.

The control is located in the overhead console. The sun shade has a one-touch open and close feature. To stop motion during one-touch operation, press the control a second time. Opening and Closing the Sun Shade

Fully press and release the front of the control to open the sun shade. Fully press and release the rear of the control to close the sun shade. Bounce-Back The sun shade will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Sun Shade Relearning WARNING

The bounce-back function is not active during this procedure. Make sure that there are no obstacles in

the way of the moving sun shade.

71