2015 Ford Fusion Owners Manual

injury.

222

Fusion (CC7) Canada/United States of America, enUSA

E176360Driving Hints

To install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in. To remove the floor mat, reverse the installation procedure.

223

Fusion (CC7) Canada/United States of America, enUSA

E142666Roadside Emergencies

ROADSIDE ASSISTANCE Vehicles Sold in the United States: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • •

24 hours a day, seven days a week. For the coverage period listed on the Roadside Assistance Card included in your Owner's Manual portfolio.

Roadside Assistance covers: • A flat tire change with a good spare, if

provided with the vehicle (except vehicles supplied with a tire inflation kit). Battery jump start. Lock-out assistance (key replacement cost is the customer's responsibility). Fuel delivery — independent service contractors, if not prohibited by state, local or municipal law, shall deliver up to 2 gal (7.6 L) of gasoline or 5 gal (18.9 L) of diesel fuel to a disabled vehicle. Roadside Assistance limits fuel delivery service to two no-charge occurrences within a 12-month period.

• Winch out — available within 100 ft

(30.5 m) of a paved or county maintained road, no recoveries. Towing — independent service contractors, if not prohibited by state, local or municipal law, shall tow Ford eligible vehicles to an authorized dealer within 35 mi (56 km) of the disablement location or to the nearest

• •

•

•

authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km).

Roadside Assistance includes up to $200
for a towed trailer if the disabled eligible vehicle requires service at the nearest authorized dealer. If the towing vehicle is operational but the trailer is not, then the trailer does not qualify for any roadside services. Vehicles Sold in the United States: Using Roadside Assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is in the owner's information portfolio in the glove compartment. United States Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company reimburses a reasonable amount for towing to the nearest dealership within 35 mi (56 km). To obtain reimbursement information, United States Ford vehicle customers call 1-800-241-3673. Customers need to submit their original receipts. Vehicles Sold in Canada: Getting Roadside Assistance Canadian customers who require roadside assistance, call 1-800-665-2006. Vehicles Sold in Canada: Using Roadside Assistance For your convenience, you may complete the roadside assistance identification card found in the centerfold of your warranty guide and retain for future reference.

224

Fusion (CC7) Canada/United States of America, enUSA

Roadside Emergencies

The hazard warning button is located on the instrument panel. Use it when your vehicle is

creating a safety hazard for other motorists. • Press the button to turn on the hazard

warning function, and the front and rear direction indicators will flash.

• Press the button again to turn them

off.

FUEL SHUTOFF

WARNING

Failure to inspect and, if necessary, repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision.

In the event of a moderate to severe collision, this vehicle includes a fuel pump shutoff feature that stops the flow of fuel to the engine. Not every impact will cause a shutoff. Should your vehicle shut off after a collision, you may restart your vehicle. For vehicles equipped with a key system: 1. Switch off the ignition. 2. Switch on the ignition. 3. Repeat Steps 1 and 2 to re-enable the

fuel pump.

For vehicles equipped with a push button start system: 1. Press the START/STOP button to

switch off the ignition.

2. Press the brake pedal and press the

START/STOP button to start the vehicle.

Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please refer to the coverage section of your warranty guide, call us in Canada at 1-800-665-2006, or visit our website at www.ford.ca. Sykes Assistance Services Corporation administers the Roadside Assistance program. You must receive covered services in Canada or the continental United States. Coverage extends to vehicles that use public, non-seasonal, annually traveled roadways. Roadside Assistance coverage does not extend to vehicles involved in cross-country driving, logging, autocross and any other form of off-road use. Well maintained roads and surfaces help ensure safe travel for the supplier, and allow their representatives to perform service as per the standard operating procedures. In Remote Locations If our supplier cannot take your vehicle by road to the nearest authorized dealership, transportation by rail or water may be necessary. The program covers a tow to the dock or rail terminal and also to the dealership at the end of the trip. For rail or water transportation, however, contact your authorized dealer to confirm if you are eligible for additional coverage before you authorize or pay for the service. Call the Ford Roadside Assistance at 1-800-665-2006 for additional information. HAZARD WARNING FLASHERS Note: If used when the vehicle is not running, the battery will lose charge. There may be insufficient power to restart your vehicle.

225

Fusion (CC7) Canada/United States of America, enUSA

Roadside Emergencies

Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle's electrical system. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch. Turn all accessories off. Connecting the Jumper Cables

WARNING

Do not attach the cables to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points. Stay clear of moving parts. To avoid reverse polarity connections, make sure that you correctly identify the positive (+) and negative (-) terminals on both the disabled and booster vehicles before connecting the cables.

Note: In the illustration, the bottom vehicle represents the booster vehicle.

3. Remove your foot from the brake pedal and press the START/STOP button to switch off the ignition.

4. You can either attempt to start the engine by pressing the brake pedal and the START/STOP button, or switch on the ignition only by pressing the START/STOP button without pressing the brake pedal. Both ways re-enable the fuel system.

Note: When you try to restart your vehicle after a fuel shutoff, the vehicle makes sure that various systems are safe to restart. Once your vehicle determines that the systems are safe, then the vehicle will allow you to restart. Note: In the event that your vehicle does not restart after your third attempt, contact an authorized dealer. JUMP STARTING THE VEHICLE

WARNINGS

The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in personal injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Use only an adequate-sized cable with insulated clamps.

Preparing Your Vehicle Note: Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. Note: Use only a 12-volt supply to start your vehicle.

226

Fusion (CC7) Canada/United States of America, enUSA

Roadside Emergencies

Jump Starting 1. Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000
rpms, as shown in your tachometer.

2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been

started, run both vehicle engines for an additional three minutes before disconnecting the jumper cables. Removing the Jumper Cables Remove the jumper cables in the reverse order that they were connected.

1. Connect the positive (+) jumper cable

to the positive (+) terminal of the discharged battery.

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.

4. Make the final connection of the

negative (-) cable to an exposed metal part of the stalled vehicle's engine, or connect the negative (-) cable to a ground connection point if available.

WARNING

Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.

A spark may cause an explosion of the gases that surround the battery.

227

Fusion (CC7) Canada/United States of America, enUSA

1. Remove the jumper cable from the ground metal surface or connecting point, if available.

4213E1426644132E142665Roadside Emergencies

• Pressing the remote control panic

button. Switching the ignition on and off twice.

•

2. Remove the jumper cable on the

negative (-) terminal of the booster vehicle's battery.

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery.

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery.

After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the battery can recharge. POST-CRASH ALERT SYSTEM The system flashes the turn signal lamps and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag (front, side, side curtain or Safety Canopy) or the safety belt pretensioners. The horn and lamps will turn off when: • •

The hazard control button is pressed The panic button (if equipped) is pressed on the remote entry transmitter Your vehicle runs out of power

• SPINOUT DETECTION If your vehicle detects a spinout and it comes to a stop, the hazard warning flashers turn on. A spinout detected message appears in the information display. The message may not appear if your vehicle runs out of power. After your vehicle's hazard warning flashers turn on, you can switch them off by: • Pressing the hazard warning flasher

button.

• Pressing the remote control unlock

button.

228

Fusion (CC7) Canada/United States of America, enUSA

Customer Assistance

These are some of the items that can be found online: • U.S. dealer locator by Dealer Name,

City/State or Zip Code.

Ford Extended Service Plans. Ford Genuine Accessories. Service specials and promotions.

• Owner Manuals. • Maintenance Schedules. • Recalls. • • • In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6K 0C8
Telephone 1-800-565-3673 (FORD) Online www.ford.ca Twitter @FordServiceCA (English Canada) @FordServiceQC (Quebec) Additional Assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center.

3.

2.

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft® parts, or remanufactured or other parts that are authorized by Ford. Away From Home If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer. In the United States: Mailing address Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
Telephone 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) Online Additional information and resources are available online at www.fordowner.com

229

Fusion (CC7) Canada/United States of America, enUSA

Customer Assistance

California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18
months of ownership of a new vehicle or the first 18000 miles (29 000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR

3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time).

In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126
You are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies conferred by California Civil Code Section 1793.22(b). You are also required to use BBB AUTO LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you choose to seek redress by pursuing rights and remedies not created by California Civil Code Section 1793.22(b) or the Magnuson-Moss Warranty Act, resort to BBB AUTO LINE is not required by those statutes.

•

In order to help us serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. •

Your telephone number (home and business). The name of the authorized dealer and city where located. The vehicle’s current odometer reading.

• In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle.

230

Fusion (CC7) Canada/United States of America, enUSA

Customer Assistance

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the Services you need section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation or you do not want to participate in mediation, and if your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. You are not bound by the decision, and may reject the decision and proceed to court where all findings of the BBB Auto Line dispute, and decision, are admissible in the court action. Should you choose to accept the BBB AUTO LINE decision, Ford is then bound by the decision, and must comply with the decision within 30 days of receipt of your acceptance letter. BBB AUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have

already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 3033 Wilson Boulevard, Suite 600
Arlington, Virginia 22201
BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation. UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.

231

Fusion (CC7) Canada/United States of America, enUSA

Customer Assistance

In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada. CAMVAP services are available in all Canadian territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685
or visit www.camvap.ca. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact our Customer Relationship Center. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company or Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the United States.

If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
Fax: (313) 390-0804
Email: [email protected] For customers in Guam, the Commonwealth of the Northern Mariana Islands (CNMI), America Samoa, and the U.S. Virgin Islands, please feel free to call our Toll-Free Number: (800) 841-FORD (3673). If your vehicle must be serviced while you are traveling or living in Puerto Rico, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (800) 841-FORD (3673) FAX: (313) 390-0804
Email: [email protected] www.ford.com.pr If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact:

232

Fusion (CC7) Canada/United States of America, enUSA

Customer Assistance

FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: +971 4 3326084
Toll-Free Number of the Kingdom of Saudi Arabia: 800 8971409
Local Telephone Number of Kuwait: 24810575
FAX: +971 4 3327299
Email: [email protected] www.me.ford.com If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing [email protected]. If you are in another foreign country, contact the nearest authorized dealer. In the event your inquiry is unresolved, communicate your concern with the dealership’s Sales Manager, Service Manager or Customer Relations Manager. If you require additional assistance or clarification, please contact the respective Customer Relationship Center as previously listed. Customers in the U.S. should call 1-800-392-3673. ORDERING ADDITIONAL OWNER'S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED 47911 Halyard Drive Plymouth, Michigan 48170
Attention: Customer Service Or to order a free publication catalog, call toll free: 1-800-782-4356

Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com (Items in this catalog may be purchased by credit card, check or money order.) Obtaining a French Owner’s Manual French Owner’s Manual can be obtained from your authorized dealer or by contacting Helm, Incorporated using the contact information listed previously in this section. REPORTING SAFETY DEFECTS (U.S. ONLY)

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company.

233

Fusion (CC7) Canada/United States of America, enUSA

E142557Customer Assistance

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590

You can also obtain other information about motor vehicle safety from http://www.safercar.gov. REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada.

Transport Canada Contact Information

Website Phone

http://www.tc.gc.ca/eng/roadsafety/menu.htm 1–800–333–0510

234

Fusion (CC7) Canada/United States of America, enUSA

Fuses

FUSE SPECIFICATION CHART Power Distribution Box WARNINGS

Always disconnect the battery before servicing high-current fuses. To reduce risk of electrical shock, always replace the cover to the power distribution box before

reconnecting the battery or refilling fluid reservoirs.

The power distribution box is located in the engine compartment. It has high-current fuses that protect your vehicle's main electrical systems from overloads. If the battery has been disconnected and reconnected, some features will need to be reset. See Changing the 12V Battery (page 254).

Fuse or relay number

Fuse amp rating

Protected components

30A3

15A1

Wide open panoramic roof 1.

Starter relay. Rain sensor.

235

Fusion (CC7) Canada/United States of America, enUSA

E190797Fuses

Fuse or relay number

Fuse amp rating

Protected components

10

11

12

13

14

15
16

17
18
19

20

21

22

23

—

20A3
—

20A1

20A1

—

20A3

15A2

15A2

10A2

10A2

—

20A3
— —

10A1

10A1

15A1

10A1

15A1

Blower motor relay. Power point 3 - Back of console.

Not used. Powertrain control module - vehicle power 1. Powertrain control module - vehicle power 2. Powertrain control module relay. Power point 1 - driver front.

Powertrain control module - vehicle power 4. Powertrain control module - vehicle power 3. Powertrain control module - vehicle power 5. Powertrain control module - vehicle power 6. Run-start relay. Power point 2 - console.

Not used. Not used. Run-start electronic power assist steering.

Run/start lighting.

Run/start transmission control. Transmission oil pump start/stop. Air conditioner clutch solenoid.

Run-start. Blind spot information system. Rear view camera. Adaptive cruise control.

236

Fusion (CC7) Canada/United States of America, enUSA

Fuses

Fuse or relay number

Fuse amp rating

Protected components

24
25

26

27
28
29

30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Heads-up display. Voltage stability module. Not used. Run-start anti-lock brake system.

Run-start powertrain control module.

Not used. Not used. Mass air flow monitor.

Not used. Not used. Electronic fan 1 relay. A/C clutch relay. Not used. Not used. Not used. Not used. Electronic fan 2 relay Electronic fan coil 2 and 3 relay. Horn relay. Not used. Fuel pump coil relay. Not used. Not used. Not used. Not used. Not used. Not used.

—

10A2

10A2
— —

5A1
— — — — — — — — — — — — — — — — — — —

237

Fusion (CC7) Canada/United States of America, enUSA

Fuses

Fuse or relay number

Fuse amp rating

Protected components

49

50

51
52
53

54

55

10A1

20A1
— —

10A1

10A2

10A2

Keep alive power.

Horn.

Not used. Not used. Power seats.

Brake on off switch.

ALT sensor.

1Micro fuse. 2Dual micro fuse. 3M-type fuse.

Power Distribution Box - Bottom There are fuses located on the bottom of the fuse box. To access the bottom of the fuse box, do the following:

238

Fusion (CC7) Canada/United States of America, enUSA

E145983Fuses

1. Release the two latches, located on

both sides of the fuse box.

2. Raise the inboard side of the fuse box

from the cradle.

3. Move the fuse box toward the center

of the engine compartment.

4. Pivot the outboard side of the fuse box

to access the bottom side.

Fuse or relay number

Fuse amp rating

Protected components

56
57

58

59

60

61
62

—

20A1

30A1

30A2

30A2
—

50A2

Not used. Diesel vaporizer or E100.

Fuel pump feed.

Electronic fan 3.

Electronic fan 1.

Not used. Body control module 1.

239

Fusion (CC7) Canada/United States of America, enUSA

E190798Fuses

Fuse or relay number

Fuse amp rating

Protected components

63

64
65

66
67

68

69

70

71
72

73

74

75

76

77

78

79

80

81

82
83

84

85

20A1
—

20A1
—

50A2

40A1

30A1

30A1
—

20A1

20A1

30A1

25A1

30A1

30A1

40A1

40A2

25A1

40A1

–

20A1

30A1

30A1

Electronic fan 2.

Not used. Front heated seat.

Not used. Body control module 2.

Heated rear window.

Anti-lock brake system valves.

Passenger seat.

Not used. Trans oil pump.

Rear heated seats.

Driver seat module.

Wiper motor 1.

Power lift-gate module.

Climate control seat module.

Trailer tow module.

Blower motor.

Wiper motor 2.

Inverter.

Not used. TRCM shifter.

Starter solenoid.

Wide open panoramic roof 2.

240

Fusion (CC7) Canada/United States of America, enUSA

Fuses

Fuse or relay number

Fuse amp rating

Protected components

86
87

1 M-type fuse. 2J-type fuse.

–

60A2

Not used. Anti-lock brake system pump.

Passenger Compartment Fuse Panel The fuse panel is located under the instrument panel to the left of the steering column.

Note: It may be easier to access the fuse panel if you remove the finish trim piece.

241

Fusion (CC7) Canada/United States of America, enUSA

E145984Fuses

Fuse or relay number

Fuse amp rating

Protected components

10

11

12

13

14

15

16

17

18

19

10A1

7.5A1

20A1

5A1

20A1

10A2

10A2

10A2

10A2

5A2

5A2

7.5A2

7.5A2

10A2

10A2

15A1

5A2

5A2

7.5A2

Lighting (ambient, glove box, vanity, dome, trunk). Memory seats, lumbar, power mirror.

Driver door unlock.

Not used (spare).

Subwoofer amplifier.

Heated seat relay coil.

Not used (spare).

Not used (spare).

Not used (spare).

Keypad. Power decklid module. Cellphone passport module. Not used (spare).

Climate control. Gear shift Steering wheel column lock. Cluster. Datelink logic. Battery electronic control module.

Datalink gateway module.

Child lock. Decklid-liftglass release. Tracking and blocking.

Ignition. Push button stop start switch. Passenger airbag disabled indicator.

242

Fusion (CC7) Canada/United States of America, enUSA

Fuses

Fuse or relay number

Fuse amp rating

Protected components

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

Transmission range Adaptive headlamp.

Humidity and in–car temperature sensor.

Occupant classification sensor.

Delayed accessory (power inverter logic, moonroof logic). Central lock unlock.

Driver door (window, mirror).

Front passenger door (window, mirror).

Moonroof.

Amplifier.

Rear driver side door (window).

Rear passenger side door (window).

Not used (spare).

Global positioning system. Display. Voice control. Adaptive cruise control. Radio frequency receiver. Active noise control. CD changer Run-start bus (fuse 19, 20, 21, 22, 35, 36, 37, circuit breaker). Restraints control module.

Auto-dimming rear view mirror. Continuous control damping suspension Rear heated seats. All wheel drive.

7.5A2

5A2

5A2

10A1

20A1

30A1

30A1

30A1

20A1

30A1

30A1

15A1

10A1

20A1

30A1

5A1

15A1

15A1

243

Fusion (CC7) Canada/United States of America, enUSA

Fuses

Fuse or relay number

Fuse amp rating

Protected components

30A

Heated steering wheel. Not used (spare).

38
1Micro fuse. 2Dual micro fuse.

CHANGING A FUSE Fuses

WARNING

Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.

If electrical components in the vehicle are not working, a fuse may have blown. A break in the fuse wire will indicate a blown fuse. Check the appropriate fuses before replacing any electrical components.

244

Fusion (CC7) Canada/United States of America, enUSA

E142430Maintenance

Working with the Engine Off 1. Set the parking brake and shift to park

(P).

2. Switch off the engine. 3. Block the wheels. Working with the Engine On

WARNING

To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

1. Set the parking brake and shift to park

(P).

2. Block the wheels OPENING AND CLOSING THE HOOD Opening the Hood

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of authorized dealers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialized tools developed specifically for servicing your vehicle. To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. See Scheduled Maintenance (page 462). If your vehicle requires professional service, an authorized dealer can provide the necessary parts and service. Check your warranty information to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft® parts are designed and built to provide the best performance in your vehicle. Precautions • Do not work on a hot engine. • Make sure that nothing gets caught in

moving parts.

• Do not work on a vehicle with the

engine running in an enclosed space, unless you are sure you have enough ventilation. Keep all open flames and other burning material (such as cigarettes) away from the battery and all fuel related parts.

•

1.

Inside the vehicle, pull the hood release handle located under the left-hand side of the instrument panel.

2. Slightly lift the hood.

245

Fusion (CC7) Canada/United States of America, enUSA

E142457Maintenance

3. Move the catch to the left.

4. Open the hood. The hood strut

automatically supports the hood.

Closing the Hood 1. Lower the hood until it engages on to

the secondary latch.

2. Firmly push down on the front of the

hood to close it fully.

Note: Make sure that the hood is correctly closed.

246

Fusion (CC7) Canada/United States of America, enUSA

E19143132E1914324Maintenance

UNDER HOOD OVERVIEW - 1.5L ECOBOOST™

Engine coolant reservoir Engine oil filler cap Engine oil dipstick Brake fluid reservoir cap Battery Power distribution box Engine air filter assembly Windshield washer fluid reservoir cap

247

Fusion (CC7) Canada/United States of America, enUSA

E184600Maintenance

UNDER HOOD OVERVIEW - 2.0L ECOBOOST™

Engine coolant reservoir cap Engine oil dipstick Engine oil filler cap Brake fluid reservoir cap Battery Power distribution box Engine air filter assembly Windshield washer fluid reservoir cap

248

Fusion (CC7) Canada/United States of America, enUSA

E159754Maintenance

UNDER HOOD OVERVIEW - 2.5L

A. Engine coolant reservoir cap B. Engine oil filler cap C. Engine oil dipstick D. Brake fluid reservoir cap E. Battery F. Power distribution box G. Air filter housing cover H. Windshield washer fluid reservoir cap

ENGINE OIL DIPSTICK - 1.5L ECOBOOST™

MIN MAX

249

Fusion (CC7) Canada/United States of America, enUSA

E169801E146020Maintenance

ENGINE OIL DIPSTICK - 2.0L ECOBOOST™/2.5L

Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers. 1. Remove the filler cap. 2.

If the engine oil level is not within the normal range, add engine oil that meets Ford specifications. See Capacities and Specifications (page 311).

3. Remove the engine oil filler cap and

use a funnel to pour the engine oil into the opening.

4. Wipe off any spilled oil. 5. Replace the filler cap. Turn it until you

feel a strong resistance.

OIL CHANGE INDICATOR RESET To reset the oil monitoring system after an oil change, See General Information (page 94).

MIN MAX

ENGINE OIL CHECK Note: Check the level before starting the engine. Note: Make sure that the level is between the MIN and the MAX marks. 1. Make sure that your vehicle is on level

ground.

2. Turn the engine off and wait 10 minutes

for the oil to drain into the oil pan.

3. Remove the dipstick and wipe it with

a clean, lint-free cloth. Replace the dipstick and remove it again to check the oil level.

If the level is at the MIN mark, add oil immediately. Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage.

250

Fusion (CC7) Canada/United States of America, enUSA

ABE169062E142732Maintenance

ENGINE COOLANT CHECK

WARNINGS

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, spilling coolant on hot engine parts can burn you.

Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine

coolant could make it difficult to see through the windshield.

To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure. steam and hot liquid can come out forcefully when you loosen the cap slightly.

Do not add coolant further than the MAX mark.

Checking the Engine Coolant When the engine is cold, check the concentration and level of the engine coolant at the intervals listed in the scheduled maintenance information. See Scheduled Maintenance (page 462). Note: Make sure that the coolant level is between the MIN and MAX marks on the coolant reservoir. Note: Coolant expands when it is hot. The level may extend beyond the MAX mark. Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately. See Adding Engine Coolant in this chapter. Maintain coolant concentration within 48% to 50%, which equates to a freeze point between -30°F (-34°C) and -34°F (-37°C).

Note: For best results, coolant concentration should be tested with a refractometer such as Robinair® Coolant and Battery Refractometer 75240. We do not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable. Do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding Engine Coolant Note: Do not use stop leak pellets, cooling system sealants or additives as they can cause damage to the engine cooling or heating systems. Your warranty may not cover these damages. Note: During normal vehicle operation, the engine coolant may change color from orange to pink or light red. As long as the engine coolant is clear and uncontaminated, this color change does not indicate the engine coolant has degraded, nor does it require the engine coolant to be drained, the system to be flushed, or the engine coolant to be replaced. Do not mix different colors or types of coolant in your vehicle. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty. Use prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 311). In case of emergency, you can add a large amount of water without engine coolant in order to reach a vehicle service location. In this instance, qualified personnel: 1. Must drain the cooling system. 2. Chemically clean the coolant system

with Motorcraft Premium Cooling System Flush.

251

Fusion (CC7) Canada/United States of America, enUSA

Maintenance

Severe Climates If you drive in extremely cold climates: •

It may be necessary to have an authorized dealer increase the coolant concentration above 50%.

• A coolant concentration of 60% will

provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.

If you drive in extremely hot climates: •

It may be necessary to have an authorized dealer decrease the coolant concentration to 40%.

• A coolant concentration of 40% will

provide improved overheat protection. Engine coolant concentrations below 40% will decrease the corrosion/freeze protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection. What You Should Know About Fail- Safe Cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The fail-safe distance depends on outside temperatures, vehicle load and terrain. How Fail-Safe Cooling Works If the engine begins to overheat, the engine coolant temperature gauge will move to the red (hot) area and:

A high engine temperature message will appear in the information display.

3. Refill with engine coolant as soon as

possible.

Water alone, without engine coolant, can cause engine damage from corrosion, overheating or freezing. Do not use the following as a coolant substitute: • Alcohol. • Methanol. • • Any engine coolant mixed with alcohol

Brine.

or methanol antifreeze or coolant.

Alcohol and other liquids can cause engine damage from overheating or freezing. Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. When adding coolant: 1. Unscrew the cap slowly. Any pressure

will escape as you unscrew the cap.

2. Add prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 311).

3. Check the coolant level in the coolant reservoir the next few times you drive your vehicle. If necessary, add enough prediluted engine coolant to bring the coolant level to the proper level.

4.

Recycled Engine Coolant Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

252

Fusion (CC7) Canada/United States of America, enUSA

Maintenance

You have limited engine power when in the fail-safe mode, so drive your vehicle with caution. Your vehicle will not maintain high-speed operation and the engine will operate poorly. Remember that the engine is capable of automatically shutting down to prevent engine damage. In this situation: 1. Pull off the road as soon as safely possible and switch off the engine. 2. Tow your vehicle to an authorized

3.

dealer. If this is not possible, wait a short period for the engine to cool.

4. Check the coolant level and add if low. 5. Re-start the engine and drive your

vehicle to an authorized dealer.

Note: Driving your vehicle without repair increases the chance of engine damage. See an authorized dealer as soon as possible. AUTOMATIC TRANSMISSION FLUID CHECK The automatic transmission does not have a transmission fluid dipstick. Have an authorized dealer check and change the transmission fluid at the correct service interval. See Scheduled Maintenance (page 462). Your transmission does not consume fluid. However, if the transmission slips, shifts slowly or if you notice a sign of leaking fluid, contact an authorized dealer. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

The service engine soon indicator will light. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs, your vehicle will still operate. However: • •

The engine power will be limited. The air conditioning system will be disabled.

Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage. When Fail-Safe Mode Is Activated

WARNINGS

Fail-safe mode is for use during emergencies only. Operate your vehicle in fail-safe mode only as long as necessary to bring your vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, your vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist, and power brake assist, which may increase the possibility of a crash resulting in serious injury.

Never remove the coolant reservoir cap while the engine is running or hot.

253

Fusion (CC7) Canada/United States of America, enUSA

Maintenance

FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. CHANGING THE 12V BATTERY

WARNINGS

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow

flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or

clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

Your vehicle is equipped with a Motorcraft® maintenance-free battery which normally does not require additional water during its life of service. Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.

BRAKE AND CLUTCH FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately. POWER STEERING FLUID CHECK Your vehicle is equipped with an electric power steering (EPS) system. There is no fluid reservoir to check or fill. WASHER FLUID CHECK

WARNING

If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze

protection. Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See Capacities and Specifications (page 311). State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.

254

Fusion (CC7) Canada/United States of America, enUSA

Maintenance

optimize the driveability and performance of the engine. Some other computer settings, like the clock and radio station presets, are also maintained in memory by power from the low voltage battery. When a technician disconnects and connects the low voltage battery, these settings are erased. Complete the following procedure in order to restore the settings: 1. With the vehicle at a complete stop,

set the parking brake.

2. Shift the transmission into P. 3. Turn off all accessories. 4. Step on the brake pedal and start the

vehicle.

5. Run the engine until it reaches normal

operating temperature. While the engine is warming up, complete the following: Reset the clock. See Audio System (page 318). Reset the power windows bounce-back feature. See Windows and Mirrors (page 82). Reset the radio station presets. See Audio System (page 318).

6. Allow the engine to idle for at least one minute. If the engine turns off, step on the accelerator to start the engine.

7. While the engine is running, step on the brake pedal and shift the transmission to N.

8. Allow the engine to run for at least one minute by pressing on the accelerator pedal.

9. Drive the vehicle at least 10 miles (16
kilometers) to completely relearn the idle and fuel trim strategy.

Note: If you do not allow the engine to relearn the idle and fuel trim strategy, the idle quality of your vehicle may be adversely affected until the engine computer