2014 Ford Fusion Owners Manual

Download PDF Manual
Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Note: In certain conditions (such as when using Max Defrost), the air conditioning compressor may continue to operate even after you switch off the air conditioning with the A/C button. Power: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle. Heated rear window: Turns the heated rear window on and off. See Heated Windows and Mirrors (page 119). Temperature control: Controls the temperature of the airflow in your vehicle. Adjust to select the desired temperature. MAX Defrost: Turn the temperature control dial all the way past the full heat position to maximize defrosting. Outside air flows through the windshield vents, fan automatically adjusts to the highest speed and the temperature dial returns to the full heat position. You can use this setting to defog or clear a thin covering of ice from the windshield. The heated rear window also automatically turns on when you select MAX Defrost. Note: To prevent window fogging, you cannot select recirculated air when MAX Defrost is on. 110 Fusion (CC7) , enUSA E144491Climate Control MAX A/C: Turn the temperature control dial all the way past the full cool position to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, the fan automatically adjusts to the highest speed and the temperature dial returns to the full cool position. Air distribution control: Press these buttons to turn airflow from the windshield, instrument panel, or footwell vents on or off. The system can distribute air through any combination of these vents. Note: At least one of these buttons remain on while the system is on. Heated seats (if equipped): Turn the driver or passenger heated seats on and off. See Heated Seats (page 127). Recirculated air: Press the button to switch between outside air and recirculated air. When recirculated air is selected, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior(when used with A/C) and may also reduce unwanted odors from entering your vehicle. Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. Fan speed indicators: Illuminate to indicate fan speed. AUTOMATIC CLIMATE CONTROL (IF EQUIPPED) 111 Fusion (CC7) , enUSA E144492Climate Control Driver temperature control: Turn to increase or decrease the air temperature for the driver side of the vehicle. This control also adjusts the passenger side temperature when not in dual zone mode. Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle. Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. Fan speed control -: Press to decrease the volume of air circulated in your vehicle. Fan speed indicator: Illuminates to indicate fan speed. When the system is controlling the fan automatically, all of the fan speed indicators turn off. Note: When the system is controlling the fan speed automatically, all of the fan speed indicators turn off. Air distribution control: Press these buttons to turn airflow from the windshield, instrument panel, or footwell vents on or off. The system can distribute air through any combination of these vents. Note: At least one of these buttons remains on while the system is on. Fan speed control +: Press to increase the volume of air circulated in your vehicle. AUTO: Press the button to turn on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature. You can also use the AUTO button to turn off dual zone operation by pressing and holding the button for more than two seconds. Passenger temperature control: Turn to increase or decrease the air temperature on the passenger side of the vehicle. This turns on dual zone mode. Heated rear window: Turns the heated rear window on and off. See Heated Windows and Mirrors (page 119). MAX Defrost: Press the button to maximize defrosting. Outside air flows through the windshield vents, and the fan automatically adjusts to the highest speed. You can use this setting to defog or clear a thin covering of ice from the windshield. The heated rear window also automatically turns on when you select MAX Defrost. Note: To prevent window fogging, you cannot select recirculated air when MAX Defrost is on. 112 Fusion (CC7) , enUSA Climate Control Power: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle. Heated seat (if equipped): Turn the driver or passenger heated seats on and off. See Heated Seats (page 127). MAX A/C: Press the button to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Note: In certain conditions (such as when using Max Defrost), the air conditioning compressor may continue to operate even after you switch off the air conditioning with the A/C button. AUTOMATIC CLIMATE CONTROL (IF EQUIPPED) Note: You can switch temperature units between Fahrenheit and Celsius. See Settings (page 354). 113 Fusion (CC7) , enUSA E144493Climate Control Driver heated seat control (if equipped): Turn the driver heated seat off and on. See Heated Seats (page 127). Driver temperature control: Press + or - to increase or decrease the air temperature for the driver side of the vehicle. This control also adjusts the passenger side temperature when not in dual zone mode. Power: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle. Fan speed control: Touch + or - to increase or decrease the volume of air circulated in the vehicle. Passenger temperature control: Press + or - to increase or decrease the air temperature on the passenger side of the vehicle. This turns on dual zone mode. Passenger heated seat control (if equipped): Turn the passenger heated seat off and on. See Heated Seats (page 127). Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle. Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Note: In certain conditions (such as when using Max Defrost), the air conditioning compressor may continue to operate even after you switch off the air conditioning with the A/C button. MAX A/C: Press the button to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. AUTO: Press the button to turn on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature. You can also use the AUTO button to turn off dual zone operation by pressing and holding the button for more than two seconds. Heated rear window: Turns the heated rear window on and off. See Heated Windows and Mirrors (page 119). Defrost: Press the button to distribute air to the windshield vents and de-mister. Air distribution to instrument panel and footwell vents turn off. You can use this setting to defog and clear the windshield of a thin covering of ice. 114 Fusion (CC7) , enUSA Climate Control MAX Defrost: Press the button to maximize defrosting. Outside air flows through the windshield vents, fan automatically adjusts to the highest speed and the temperature dial returns to the full heat position. You can use this setting to defog or clear a thin covering of ice from the windshield. The heated rear window also automatically turns on when you select MAX Defrost. Note: To prevent window fogging, you cannot select recirculated air when MAX Defrost is on. AUTOMATIC CLIMATE CONTROL (IF EQUIPPED) Note: You can switch temperature units between Fahrenheit and Celsius. See Settings (page 354). AUTO: Press the button to turn on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature. You can also use the AUTO button to turn off dual zone operation by pressing and holding the button for more than two seconds. CLIMATE: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle. 115 Fusion (CC7) , enUSA E144494Climate Control MAX A/C: Press the button to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Note: In certain conditions (such as when using Max Defrost), the air conditioning compressor may continue to operate even after you switch off the air conditioning with the A/C button. Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle. Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. Passenger temperature control: Press + or - to increase or decrease the air temperature on the passenger side of the vehicle. This turns on dual zone mode. Fan speed control: Touch + or - to increase or decrease the volume of air circulated in the vehicle. Driver temperature control: Press + or - to increase or decrease the air temperature for the driver side of the vehicle. This control also adjusts the passenger side temperature when not in dual zone mode. MAX Defrost: Press the button to maximize defrosting. Outside air flows through the windshield vents, and the fan automatically adjusts to the highest speed. You can use this setting to defog or clear a thin covering of ice from the windshield. The heated rear window also automatically turns on when you select MAX Defrost. Note: To prevent window fogging, you cannot select recirculated air when MAX Defrost is on. Heated rear window: Turns the heated rear window on and off. See Heated Windows and Mirrors (page 119). Defrost: Press the button to distribute air to the windshield vents and de-mister. Air distribution to instrument panel and footwell vents turn off. You can use this setting to defog and clear the windshield of a thin covering of ice. 116 Fusion (CC7) , enUSA Climate Control HINTS ON CONTROLLING THE INTERIOR CLIMATE General Hints Note: Prolonged use of recirculated air may cause the windows to fog up. Note: You may feel a small amount of air from the footwell air vents regardless of the air distribution setting. Note: To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on. Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Note: Remove any snow, ice or leaves from the air intake area at the base of the windshield. Note: To improve the time to reach comfort in hot weather, drive with the windows slightly open for 2-3 minutes after start-up or until your vehicle airs out. Heating the Interior Quickly Vehicle with manual climate control Adjust the fan speed to the highest speed setting. Adjust the temperature control to the highest setting. Select the footwell air vents using the air distribution buttons. Manual Climate Control Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position. Automatic Climate Control Note: Adjusting the settings when your vehicle interior is extremely hot or cold is not necessary. The system automatically adjusts to heat or cool the cabin to your selected temperature as quickly as possible. For the system to function efficiently, the instrument panel and side air vents should be fully open. Note: If you select AUTO during cold outside temperatures, the system directs airflow to the windshield and side window vents. In addition, the fan may run at a slower speed until the engine warms up. Note: If you select AUTO during hot outside temperatures, or when the inside of the vehicle is hot, the system automatically uses recirculated air to maximize interior cooling. When the interior reaches the selected temperature, the system automatically switches to using outside air. Vehicle with automatic climate control Press the AUTO button. Adjust the temperature control to the desired setting. 117 Fusion (CC7) , enUSA Climate Control Recommended Settings for Heating Vehicle with manual climate control Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the hot settings. Select the footwell air vents using the air distribution buttons. Cooling the Interior Quickly Vehicle with manual climate control Adjust the temperature control to the MAX A/C position. Drive with the windows open for 2-3 minutes. Recommended Settings for Cooling Vehicle with manual climate control Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the cold settings. Select the instrument panel air vents using the air distribution buttons. Vehicle with automatic climate control Press the AUTO button. Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary. Vehicle with automatic climate control Press the MAX A/C button. Vehicle with automatic climate control Press the AUTO button. Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary. 118 Fusion (CC7) , enUSA Climate Control Side Window Defogging in Cold Weather Vehicle With Automatic Climate Control Press the defrost button. Adjust the temperature control to the desired setting. Use 72°F (22°C) as a starting point, then adjust the setting as necessary. Vehicle With Manual Climate Control Select the instrument panel and footwell air vents positions through the air distri- bution control. Press the A/C button. Adjust the temperature control to the desired setting. Adjust the fan speed to the highest setting. Direct the instrument panel side air vents toward the side windows. Close the instrument panel center vents. HEATED WINDOWS AND MIRRORS (IF EQUIPPED) Heated Rear Window Note: You must switch the ignition on to use this feature. Press the button to clear the rear window of thin ice and fog. It switches off automatically after 10 minutes, or when you switch off the ignition. You can also press the button again to switch it off. Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window. This may cause damage to the heated grid lines. Your warranty does not cover this damage. Heated Exterior Mirror (If Equipped) Note: Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass that has frozen in place. These actions could cause damage to the glass and mirrors. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. The heated mirrors remove ice, mist and fog when you switch on the heated rear window. CABIN AIR FILTER Your vehicle is equipped with a cabin air filter. It is located behind the glove box. The particulate filtration system reduces the concentration of airborne particles such as dust, spores and pollen in the air supplied to the interior of your vehicle. 119 Fusion (CC7) , enUSA E72507Climate Control You can adjust the default remote start settings using the information display controls. See Information Displays (page 87). Automatic Settings In hot weather, the system is set to 72°F (22°C). The cooled seats are set to high (if available, and selected to AUTO in the information display). In moderate weather, the system either heats or cools (based on previous settings). The rear defroster, heated mirrors and heated seats do not automatically turn on. In cold weather, the system is set to 72°F (22°C). The heated seats are set to high (if available, and selected to AUTO in the information display). The rear defroster and heated mirrors automatically turn on. Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. The particulate filtration system gives you and your passengers the following benefits: • It improves your driving comfort by reducing particle concentration. It improves the interior compartment cleanliness. It protects the climate control components from particle deposits. • • Replace the filter at regular intervals. See Scheduled Maintenance (page 428). For additional cabin air filter information, or to replace the filter, see an authorized dealer. REMOTE START (IF EQUIPPED) The remote start feature allows you to pre-condition the interior of your vehicle. The climate control system works to achieve comfort according to your previous settings. Note: You cannot adjust the system during remote start operation. Turn the ignition on to return the system to its previous settings. You can now make adjustments normally, but you need to turn certain vehicle-dependent features back on, such as: • Heated seats. • Cooled seats. • Heated steering wheel. • Heated mirrors. • Heated rear window. 120 Fusion (CC7) , enUSA Seats We recommend that you follow these guidelines: • Sit in an upright position with the base of your spine as far back as possible. • Do not recline the seat back more than 30 degrees. • Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 inches (25 centimeters) between your breastbone and the air bag cover. • • Hold the steering wheel with your arms slightly bent. Bend your legs slightly so that you can press the pedals fully. • • Position the shoulder strap of the safety belt over the center of your shoulder and position the lap strap tightly across your hips. Make sure that your driving position is comfortable and that you can maintain full control of your vehicle. HEAD RESTRAINTS WARNINGS Fully adjust the head restraint before you sit in or operate your vehicle. This will help minimize the risk of neck injury in the event of a collision. Do not adjust the head restraint when your vehicle is moving. The head restraint is a safety device. Whenever possible it should be installed and properly adjusted when the seat is occupied. SITTING IN THE CORRECT POSITION WARNINGS Sitting improperly, out of position or with the seat back reclined too far can take weight off the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in the event of a crash. Always sit upright against your seat back, with your feet on the floor. Do not recline the seat back as this can cause the occupant to slide under the safety belt, resulting in serious injury in the event of a crash. Do not place objects higher than the seat back to reduce the risk of serious injury in the event of a crash or during heavy braking. When you use them properly, the seat, head restraint, safety belt and air bags will provide optimum protection in the event of a crash. 121 Fusion (CC7) , enUSA E68595Seats WARNINGS Install the head restraint properly to help minimize the risk of neck injury in the event of a collision. Note: Adjust the seat back to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position. Front seat and rear seat outboard head restraints Rear center head restraint The head restraints consist of: An energy absorbing head restraint Two steel stems Guide sleeve adjust and unlock button Guide sleeve unlock and remove button Adjusting the Head Restraint Raising the Head Restraint Pull the head restraint up. Lowering the Head Restraint 1. Press and hold button C. 2. Push the head restraint down. Removing the Head Restraint 1. Pull the head restraint up until it reaches its highest position. 2. Press and hold buttons C and D. 3. Pull the head restraint up. Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until in locks. Tilting Head Restraints The front head restraints have a tilting feature for extra comfort. To tilt the head restraint, do the following: 122 Fusion (CC7) , enUSA E138642E138645Seats The manual front seats may consist of: 1. Adjust the seat back to an upright driving or riding position. 2. Pivot the head restraint forward toward your head to the desired position. After the head restraint reaches the forward-most tilt position, pivoting it forward again will then release it to the rearward, un-tilted position. MANUAL SEATS WARNINGS Do not adjust the driver's seat or seat back when your vehicle is moving. Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged. Reclining the seat back can cause an occupant to slide under the seat's safety belt, resulting in severe personal injuries in the event of a collision. a bar to move the seat backward and forward a control to adjust the lumbar of the seat back a lever to adjust the height of the seat a lever to adjust the angle of the seat back POWER SEATS (IF EQUIPPED) WARNINGS Do not adjust the driver's seat or seatback when your vehicle is moving. Do not place cargo or any objects behind the seatback before returning it to the original position. 123 Fusion (CC7) , enUSA E144727ABCDE144631Seats Power Lumbar (If Equipped) MEMORY FUNCTION (IF EQUIPPED) WARNINGS Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts. Do not use the memory function when your vehicle is moving. This feature will automatically recall the position of the driver's seat and power mirrors. The memory control is located on the driver’s door. 124 Fusion (CC7) , enUSA E144632E165608Seats 1. With the ignition on, move the memory positions to the desired positions. 2. Press and hold the desired pre-set button for about five seconds. A chime will sound after about two seconds. Continue holding until a second chime is heard. 3. Within three seconds, press the lock button on the remote control you are linking. To unlink a remote control, follow the same procedure – except in step 3, press the unlock button on the remote control. Note: To stop seat movement during a recall, press any driver seat adjustment control, any of the memory buttons, or any mirror control switch. Seat movement will also stop if you move your vehicle. Note: If more than one linked remote control or intelligent access key is in range, the memory function will move to the settings of the first key stored. Easy Entry and Exit Function If you enable the easy entry and exit feature, it automatically moves the driver seat position rearward up to five centimeters when the transmission selector lever is in position P and you remove the key or turn off the keyless start ignition. The driver seat will return to the previous position when you put the key in the ignition or you activate the keyless start ignition. You can turn off the easy entry and exit feature by using the driver information display. Saving a Pre-Set Position 1. Switch the ignition on. 2. Adjust the seat and exterior mirrors to your desired position. 3. Press and hold the desired pre-set button until you hear a single chime. You can save up to three pre-set memory positions. You can save a memory pre-set at any time. Recalling a Pre-Set Position Press and release the pre-set button associated with your desired driving position. The seat and mirrors will move to the position stored for that pre-set. Note: A pre-set memory position can only be recalled when the ignition is off, or when the transmission selector lever is in position P or N (and your vehicle is not moving) if the ignition is on. You can recall a pre-set memory position by pressing the unlock button on your remote control or intelligent access key if it is linked to a pre-set position. Linking a Pre-Set Position to your Remote Control or Intelligent Access Key Your vehicle can save the pre-set memory positions for up to three remote controls or intelligent access (IA) keys. 125 Fusion (CC7) , enUSA E142554Seats REAR SEATS Note: Your vehicle may have split seatbacks that you must fold individually. Note: Make sure the center safety belt is unbuckled before folding the seatback. To lower the seat back(s) from inside the vehicle, do the following: 3. Stow the safety belt in the stowage clip. This will prevent the safety belt from getting caught in the seat latch. When raising the seat back(s), make sure you hear the seat latch into place. 1. Pull the handle to release the seatback. 2. Push the seatback forward. 126 Fusion (CC7) , enUSA E144634E164098Seats HEATED SEATS (IF EQUIPPED) WARNING People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury. Do not do the following: • Place heavy objects on the seat. • Operate the heated seat if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly. • Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge. VENTILATED SEATS (IF EQUIPPED) The ventilated seats will only function when the engine is running. To operate the ventilated seats: Press the ventilated seat symbol to cycle through the various cooling settings and off. Cooler settings are indicated by more indicator lights. If the engine falls below 350 RPM while the ventilated seats are on, the feature will turn itself off and you will need to reactivate it. Heated and ventilated seat air filter replacement (if equipped) Your vehicle is equipped with lifetime air filters that are integrated with the seats. Regular maintenance or replacement is not needed. REAR SEAT ARMREST Press the heated seat symbol to cycle through the various heat settings and off. Warmer settings are indicated by more indicator lights. 127 Fusion (CC7) , enUSA E146941E146309E144635Seats Fold the armrest down to use the armrest and cupholder. 128 Fusion (CC7) , enUSA Universal Garage Door Opener HomeLink Wireless Control System (If Equipped) WARNING Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982). A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. Note: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. Note: We recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the function button codes later in this section. Note: You can program a maximum of three devices. To change or replace any of the three devices after it has been initially programmed, you must first erase the current settings. See Erasing the function button codes later in this section. The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. The system includes two primary features, a garage door opener and a platform for remote activation of devices within the home. As well as being programmed for garage doors, the system transmitter can be programmed to operate entry gate operators, security systems, entry door locks and home or office lighting. Additional system information can be found online at www.homelink.com or by calling the toll-free help line on 1-800-355-3515. In-vehicle programming This process is to program your hand-held transmitter and your in-vehicle HomeLink button. Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal. 1. With your vehicle parked outside of the garage, turn your ignition to the on position, but do not start your vehicle. 2. Hold your hand-held garage door transmitter 1–3 inches (2–8 centimeters) away from the HomeLink button you want to program. 129 Fusion (CC7) , enUSA E142657E142658Universal Garage Door Opener 3. Using both hands, simultaneously, press and hold the desired HomeLink button and the hand-held transmitter button. DO NOT release either one until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing indicates successful training. 4. Press and hold the HomeLink button you programmed for five seconds, then release. You may need to do this twice to activate the door. If your garage door does not operate, watch the HomeLink indicator light. If the indicator light stays on, the programming is complete. See Programming your garage door motor later in this section. If the indicator light flashes rapidly for 2 seconds and then turns to a constant light, the HomeLink button is not programmed yet. Do the following: Press and hold the HomeLink button while you press and release the hand-held transmitter button every 2 seconds. The HomeLink indicator light will flash slowly and then rapidly once the HomeLink function button recognizes and accepts the hand-held transmitter’s radio frequency signal. After programming the HomeLink button, begin programming your garage door opener motor. Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener. 130 Fusion (CC7) , enUSA To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515. Programming your garage door opener motor 1. Press the learn button on the garage door opener motor and then you have 30 seconds to complete the next two steps. 2. Return to your vehicle. 3. Press and hold the function button you want to program for 2 seconds, then release. Repeat this step. Depending on your brand of garage door opener, you may need to repeat this sequence a third time. Erasing the Function Button Codes Note: You cannot erase individual buttons. E142659E142658Universal Garage Door Opener A. B. Red indicator light Green indicator light 1. Press and hold one of the buttons on the hand-held transmitter for 10 seconds. The indicator light will change from green to red and green. 2. Press the same button twice to confirm the change to programming mode. If done properly the indicator light will appear red. 3. Hold the transmitter within 1–3 inches (2–8 centimeters) of the button on the visor you want to program. 4. Press and hold both the programmed Genie button on the hand-held transmitter and the button you want to program. The indicator light on the visor will flash rapidly when the programming is successful. Note: The Genie transmitter will transmit for up to 30 seconds. If HomeLink does not program within 30 seconds the Genie transmitter will need to be pressed again. If the Genie transmitter indicator light displays green and red, release the button until the indicator light turns off before pressing the button again. Once HomeLink has been programmed successfully, the Genie transmitter must be changed out of program mode. To do this: 1. Press and hold the outer two function buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly. 2. When the indicator lights flash, release the buttons. The codes for all buttons are erased. Reprogramming a Single Button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the button, follow Step 1 in the Programming section. For questions or comments, contact HomeLink at www.homelink.com or 1-800-355-3515. Programming to a Genie Intellicode 2 Garage Door Opener Note: The Genie Intellicode 2 transmitter must already be programmed to operate with the garage door opener. Note: To program HomeLink to the transmitter you must first put the transmitter into programming mode. 131 Fusion (CC7) , enUSA E142660BAE142661Universal Garage Door Opener 5. Press and hold the previously programmed button on the visor for 2 seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete. Clearing a HomeLink Device To erase programming from the three HomeLink buttons press and hold the two outer HomeLink buttons until the indicator light begins to flash. The indicator light will begin flashing in 10 to 20 seconds, at which time both buttons should be released. Programming has now been erased, and the indicator light should blink slowly to indicate the device is in train mode when any of the three HomeLink buttons are pressed. FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to your device not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment. 1. Press and hold the previously programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green. 2. Press the same button twice to confirm the change. If done correctly the indicator light will turn green. Programming HomeLink to the Genie Intellicode Garage Door Opener Motor Note: You may need a ladder to access the garage door opener motor. 1. Press and hold the program button on the garage door opener motor until both blue indicator lights turn on. 2. Release the program button. Only the smaller round indicator light should be on. 3. Press and release the program button. The larger purple indicator light will flash. Note: The next two steps must be completed in 30 seconds. 4. Press and release the Genie Intellicode 2 hand-held transmitter’s previously programmed button. Both indicator lights on the garage door opener motor unit should now flash purple. 132 Fusion (CC7) , enUSA E142662Auxiliary Power Points 12 Volt DC Power Point WARNING Do not plug optional electrical accessories into the cigar lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. Note: If used when the vehicle is not running, the battery will discharge. There may be insufficient power to restart your vehicle. Note: Do not insert objects other than an accessory plug into the power point. This will damage the outlet and blow the fuse. Note: Do not hang any type of accessory or accessory bracket from the plug. Note: Do not use the power point over the vehicle capacity of 12 volt DC 180 watts or a fuse may blow. Note: Do not use the power point for operating a cigar lighter element. Note: Improper use of the power point can cause damage not covered by your warranty. Note: Always keep the power point caps closed when not in use. Run the vehicle for full capacity use of the power point. To prevent the battery from discharging accidentally: • Do not use the power point longer than necessary when the vehicle is not running. • Do not leave devices plugged in overnight or when you park your vehicle for extended periods. Locations Power points may be in the following locations: Fusion (CC7) , enUSA in the front of the center console inside the center console storage bin on the rear of the center console. • • • 110 Volt AC Power Point (If Equipped) WARNING Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design. Doing so my cause the power point to overload due to powering multiple devices that can reach beyond the 150 watt load limit and could result in fire or serious injury. Note: Keep the vehicle running to use the power point. You can use the power point for powering electrical devices that require up to 150 watts. It is on the rear of the center console. When the indicator light, located on the power point, is: • on — power point is ready to supply power. off — power point power supply is off; ignition is not on. flashing — power point is in fault mode. • • 133 E143941Auxiliary Power Points The power point temporarily turns off power if it exceeds the 150 watt limit. It can also switch to a fault mode if it detects overloading, overheating, or shorting conditions. For overloading and shorting conditions, unplug your device and switch the ignition off then on. For an overheating condition, let the system cool off first. Switch the ignition off then on. Do not use the power point for certain electric devices, including: • Cathode ray tube type televisions • Motor loads, for example vacuum cleaners, electric saws and other electric power tools, or compressor-driven refrigerators • Measuring devices which process precise data, for example medical equipment or measuring equipment • Other appliances requiring an extremely stable power supply, for example microcomputer-controlled electric blankets or touch sensor lamps 134 Fusion (CC7) , enUSA Storage Compartments CENTER CONSOLE Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. Available console features include: Cupholder Storage compartment with auxiliary power point, auxiliary input jack, USB port and media hub Auxiliary power point OVERHEAD CONSOLE Press near the rear edge of the door to open it. 135 Fusion (CC7) , enUSA ABCE143942E75193Starting and Stopping the Engine GENERAL INFORMATION IGNITION SWITCH WARNINGS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. 0 (off) - The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. I (accessory) - Allows the electrical accessories, such as the radio, to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. II (on) - All electrical circuits are operational and the warning lamps and indicators illuminate. III (start) - cranks the engine. KEYLESS STARTING Note: The keyless starting system may not function if the key is close to metal objects or electronic devices such as cellular phones. Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine. Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, creating the risk of fire. Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. If you smell exhaust fumes inside your vehicle, have your vehicle checked by an authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period. The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise. When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine. 136 Fusion (CC7) , enUSA E72128Starting and Stopping the Engine Note: You can crank the engine for a total of 60 seconds (without the engine starting) before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine three times for 20 seconds each time, without the engine starting, you reached the 60-second time limit. A message appears in the information display alerting you that you exceeded the cranking time. You cannot attempt to start the engine for at least 15 minutes. After 15 minutes, you are limited to a 15-second engine cranking time. You need to wait 60 minutes before you can crank the engine for 60 seconds again. Before starting the engine, check the following: • Make sure all occupants have fastened their safety belts. • Make sure the headlamps and electrical accessories are off. • Make sure the parking brake is on. • Move the transmission selector lever to position P (automatic transmission) or neutral (manual transmission). Turn the ignition key to position II. If your vehicle is equipped with a keyless ignition, see the following instructions. • Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. If your vehicle is equipped with a manual transmission, fully press the clutch pedal also. 2. Turn the key to position III to start the engine. Release the key when the engine starts. Note: The engine may continue cranking for up to 15 seconds or until it starts. Note: If you cannot start the engine on the first try, wait for a short period and try again. Ignition Modes The keyless starting system has three modes: Off: Turns the ignition off. • Without applying the brake pedal, press and release the button once when the ignition is in the on mode, or when the engine is running but the vehicle is not moving. On: All electrical circuits are operational and the warning lamps and indicators illuminate. • Without applying the brake pedal, press and release the button once. Start: Starts the engine. • Press the brake pedal, and then press the button for any length of time. An indicator light on the button illuminates when then ignition is on and when the engine starts. STARTING A GASOLINE ENGINE When you start the engine, the idle speed increases, this helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer. 137 Fusion (CC7) , enUSA E144447Starting and Stopping the Engine Within 20 seconds of switching the engine off, press the brake pedal and press the button. After 20 seconds have expired, you can no longer restart the engine without the key present inside your vehicle. Once the engine has started, it remains running until you press the button, even if the system does not detect a valid key. If you open and close a door while the engine is running, the system searches for a valid key. You cannot restart the engine if the system does not detect a valid key within 20 seconds. Failure to Start If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure: 1. If your vehicle is equipped with an automatic transmission, fully press the brake pedal. If your vehicle is equipped with a manual transmission, fully press the clutch pedal and apply the handbrake. 2. Move the transmission selector lever to park (P) (automatic transmission) or neutral (manual transmission). 3. Fully press the accelerator pedal and hold it there. 4. Start the engine. Automatic Engine Shutdown If your vehicle is equipped with a keyless ignition, it has a feature that automatically shuts down the engine if it has been idling for an extended period. The ignition also turns off in order to save battery power. Before the engine shuts down, a message appears in the information display showing a timer counting down from 30 seconds. Vehicles with Keyless Start Note: Do not touch the accelerator pedal. Note: You must have your intelligent access key in the vehicle in order to shift the transmission out of position P. 1. Fully press the brake pedal. 2. Press the button. The system does not function if: • • If you are unable to start the engine, do the following: The key frequencies are jammed. The key battery has no charge. 1. Locate the key backup slot in center console utility compartment. 2. With the buttons facing the rear of the vehicle and the key ring up, place the key into backup slot. 3. With the key in this position, press the brake pedal, and then the button to switch on the engine. Fast Restart The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. 138 Fusion (CC7) , enUSA E147165Starting and Stopping the Engine Vehicles with Keyless Start 1. Move the transmission selector lever to position P. 2. Press the button once. 3. Apply the parking brake. Note: This switches off the ignition, all electrical circuits, warning lamps and indicators. Note: If the engine is idling for 30 minutes, the ignition and engine automatically shut down. Stopping the Engine When Your Vehicle is Moving WARNING Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not lock, but higher effort will be required. When the ignition is switched off, some electrical circuits, warning lamps and indicators may also be off. Vehicles with an Ignition Key 1. Move the transmission selector lever to position N (automatic transmission) or neutral (manual transmission) and use the brakes to bring your vehicle to a safe stop. 2. When your vehicle has stopped, move the transmission selector lever to position P (automatic transmission) or 1 (manual transmission) and turn the key to position 0. 3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop. If you do not intervene within 30 seconds, the engine shuts down. Another message appears in the information display to inform you that the engine has shut down in order to save fuel. Start your vehicle as you normally do. Automatic Engine Shutdown Override Note: You cannot permanently switch off the automatic engine shutdown feature. When you switch it off temporarily, it turns on at the next ignition cycle. You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: • You can reset the timer by interacting with your vehicle (such as pressing the brake pedal or accelerator pedal). You can temporarily switch off the shutdown feature any time the ignition is on (for the current ignition cycle only). Use the information display to do so. See Information Displays (page 87). • • During the countdown before engine shutdown, you are prompted to press OK or RESET (depending on your type of information display) to temporarily switch the feature off (for the current ignition cycle only). Stopping the Engine When Your Vehicle is Stationary Vehicles with an Ignition Key 1. Move the transmission selector lever to position P (automatic transmission) or 1 (manual transmission). 2. Turn the key to position 0. 3. Apply the parking brake. 139 Fusion (CC7) , enUSA Starting and Stopping the Engine 2. When your vehicle has stopped, move the transmission selector lever to position P. 3. Press and hold the button for one second, or press it three times within two seconds. 4. Apply the parking brake. Guarding Against Exhaust Fumes WARNING If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and the leave the engine idling for long periods, we recommend that you do one of the following: • Open the windows at least 1 inch (2.5 centimeters) Set your climate control to outside air. • ENGINE BLOCK HEATER (IF EQUIPPED) WARNINGS Failure to follow engine block heater instructions could result in property damage or serious personal injury. Do not use your heater with ungrounded electrical systems or two-pronged adapters. There is a risk of electrical shock. Note: The heater is most effective when outdoor temperatures are below 0°F (-18°C). The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source. We recommend that you do the following for a safe and correct operation: • Use a 16-gauge outdoor extension cord that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA). This extension cord must be suitable for use outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard. • Use as short an extension cord as possible. • Do not use multiple extension cords. • Make sure that when in operation, the extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire. • Make sure your vehicle is parked in a clean area, clear of combustibles. • Make sure the heater, heater cord and extension cord are firmly connected. • Check for heat anywhere in the electrical hookup once the system has been operating for approximately 30 minutes. • Make sure the heater system is checked for proper operation before winter. 140 Fusion (CC7) , enUSA Starting and Stopping the Engine Using the Engine Block Heater The engine block heater plug is located in a housing in the left fog lamp bezel. Open the hinged, circular door and make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.0 kilowatt-hours of energy per hour of use. The system does not have a thermostat. It will achieve maximum temperature after approximately three hours of operation. If you use the heater longer than three hours, this will not improve system performance and will use unnecessary electricity. 141 Fusion (CC7) , enUSA Unique Driving Characteristics • • • • • • • • • • • Your foot is on the brake pedal. The transmission is in drive (D). The driver's door is closed. There is adequate brake vacuum. The interior compartment has been cooled or warmed to an acceptable level. The front windshield defroster and rear window defroster are off. The steering wheel is not turned rapidly or is not at a sharp angle. The vehicle is not on a steep road grade. The battery is within optimal operating conditions (battery state of charge and temperature in range). The engine coolant is at operating temperature. Elevation is below approximately 10000 feet (3048 meters). • Ambient temperature is moderate. Note: The system allows multiple successive Auto StartStop events, but it may not operate in conditions of heavy traffic or in extended low speed operation. Note: The green Auto StartStop indicator light on the instrument cluster will illuminate to indicate when the automatic engine stop occurs. Note: If the instrument cluster is equipped with a grey Auto StartStop indicator light, it is illuminated when automatic engine stop is not available due to one of the above noted conditions not being met. Automatic Engine Restart Any of the following conditions will result in an automatic restart of the engine: AUTO-START-STOP (IF EQUIPPED) The system helps reduce fuel consumption by automatically shutting off and restarting the engine while your vehicle is stopped. The engine will restart automatically when you release the brake pedal. In some situations, your vehicle may restart automatically, for example: • • Note: Power assist steering is turned off when the engine is off. To maintain interior comfort To recharge the battery WARNINGS The engine may restart automatically if required by the system. Switch the ignition off before opening the hood or performing any maintenance. Failure to do so may result in serious injuries due to automatic engine restart. Always switch the ignition off before leaving your vehicle, as the system may have turned the engine off, but the ignition will still be on and automatic restart may occur. The Auto StartStop system status is available at a glance within the information display. See Information Displays (page 87). Enabling Auto StartStop The system is automatically enabled every time you start your vehicle if the following conditions are met: • The Auto StartStop button is not pressed (not illuminated). Your vehicle exceeds an initial speed of 3 mph (4 km/h) after the vehicle has been initially started. Your vehicle is stopped. • • 142 Fusion (CC7) , enUSA E146361Unique Driving Characteristics Disabling Auto StartStop Press the Auto StartStop button located on the center console to switch the system off. The button will illuminate. The system will only be deactivated for the current ignition cycle. Press the button again to restore Auto StartStop function. Note: If the Shift to P, Restart Engine message appears and the amber Auto StartStop indicator light is flashing, automatic restart is not available. The vehicle must be restarted manually. See Information Displays (page 87). • • • • • • • • • • Your foot is removed from the brake pedal. You press the accelerator pedal. You press the accelerator and the brake pedal at the same time. The driver seat belt becomes unfastened or the driver door is ajar. The transmission is moved from drive (D). Your vehicle is moving. The interior compartment does not meet customer comfort when air conditioning or heat is on. Fogging of the windows could occur and the air conditioning is on. The battery is not within optimal operating conditions. The maximum engine off time is exceeded. • When you press the Auto StartStop button while the engine is stopped automatically. Either the front or rear defroster is turned on. • Any of the following conditions may result in an automatic restart of the engine: • The blower fan speed is increased or the climate control temperature is changed. • An electrical accessory is turned on or plugged in. 143 Fusion (CC7) , enUSA PRNDSE146362Fuel and Refueling SAFETY PRECAUTIONS WARNINGS Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. Automotive fuels can cause serious injury or death if misused or mishandled. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. Fusion (CC7) , enUSA • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin, clothing or both, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction. • • 144 Fuel and Refueling Choosing the Right Fuel (Flex Fuel Vehicles) Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 85% ethanol (E-85) in your flex fuel vehicle (FFV). If your vehicle is flex fuel capable, it will have a yellow bezel placed over the fuel fill inlet. Do not use: • Fuels containing more than 85% ethanol or E-100 fuel. Fuels containing methanol. Fuels containing metallic based additives, including manganese-based compounds. Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT). Leaded-fuel (The use of leaded fuel is prohibited by law). • • • • Note: Use of any fuel other than recommended fuel can cause powertrain damage, impair the emission control system or cause loss of vehicle performance. Any damage to vehicle that is caused by use of fuel not recommended will not be covered under warranty. Octane Recommendations 2.5L engine Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some fuel stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended. 1.6L and 2.0L EcoBoost® engines FUEL QUALITY Note: Use of any fuel other than those recommended may cause vehicle damage, a loss of vehicle performance and repairs may not be covered under warranty. Choosing the Right Fuel (Gasoline Vehicles) Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 15% ethanol in your gasoline vehicle. If your vehicle is a Flex Fuel Vehicle (FFV), it will have a yellow bezel placed over the fuel fill inlet. Do not use: • Fuels containing more than 15% ethanol or E-85 fuel. Fuels containing methanol. Fuels containing metallic based additives, including manganese-based compounds. Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT). Leaded-fuel (The use of leaded fuel is prohibited by law). • • • • Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. The use of leaded fuel is prohibited by law. Note: Use of any fuel other than recommended fuel can cause powertrain damage, impair the emission control system or cause loss of vehicle performance. Any damage to vehicle that is caused by use of fuel not recommended will not be covered under warranty. 145 Fusion (CC7) , enUSA Fuel and Refueling Refilling With a Portable Fuel Container WARNINGS Do not insert the nozzle of portable fuel containers or aftermarket funnels into the capless fuel system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, which could result in serious personal injury. Do not try to pry open or push open the capless fuel system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others. Note: Do not use aftermarket funnels; they will not work with the capless fuel system and can damage it. The included fuel funnel has been specially designed to work safely with your vehicle. When filling the vehicle’s fuel tank from a portable fuel container, use the funnel included with the vehicle. Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as "Regular" with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended. Premium fuel will provide improved performance and is recommended for severe duty usage such as trailer tow. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage. RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. With keyless ignition, just start the engine. Crank time will be longer than usual.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2014 Ford Fusion Owners Manual