Fuel Gauge Engine Coolant Temperature Gauge
Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled.
Outside Air Temperature Shows the outside air temperature. Compass Displays the vehicle’s heading direction. Trip Computer See General Information (page 87).
80
Fusion (CC7) , enUSA
E144485Instrument Cluster
Vehicle Settings and Personalization See General Information (page 87). Engine Coolant Temperature Gauge Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the center section. If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down. Note: Do not restart the engine until the cause of overheating has been resolved.
WARNING
Never remove the coolant reservoir cap while the engine is running or hot.
Fuel Gauge Note: The fuel gauge may vary slightly when your vehicle is moving or on a gradient.
Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. The needle should move toward F when you refuel your vehicle. If the needle points to E after adding fuel, this indicates your vehicle needs service soon. After refueling some variability in needle position is normal: •
It may take a short time for the needle to reach F after leaving the gas station. This is normal and depends upon the slope of pavement at the gas station. The fuel amount dispensed into the tank is a little less or more than the gauge indicated. This is normal and depends upon the slope of pavement at the gas station. If the gas station nozzle shuts off before the tank is full, try a different gas pump nozzle. Low Fuel Reminder A low fuel reminder triggers when the fuel gauge needle is at 1/16th.
•
•
Variations:
Driving type (fuel economy
conditions)
Highway driving
Severe duty driving (trailer
towing, extended idle)
Fuel gauge position
Distance-to-empty
1/16th
1/16th
35 miles to 80 miles (56 km
to 129 km)
35 miles (56km)
81
Fusion (CC7) , enUSA
Instrument Cluster
Type 3
Left Information Display Speedometer Right Information Display See General Information (page 87).
Left Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. Trip Computer See General Information (page 87). Vehicle Settings and Personalization See General Information (page 87).
WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.
82
Fusion (CC7) , enUSA
E144486Instrument Cluster
Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle. Adaptive Cruise Control (If Equipped)
The speed control system indicator light changes color to indicate what mode the system is in: See Using Cruise Control (page 179). On (white light): Illuminates when the adaptive cruise control system is turned on. Turns off when the speed control system is turned off. Engaged (green light): Illuminates when the adaptive cruise control system is engaged. Turns off when the speed control system is disengaged. Anti-Lock Braking System
If it illuminates when you are driving, this indicates a malfunction. You will continue
to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer. Auto Start-stop (If Equipped)
It will illuminate to inform you when the engine shuts down or in conjunction with a message.
Battery
If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical
equipment and have the system checked by your authorized dealer immediately.
Blind Spot Monitor (If Equipped)
It will illuminate when you switch this feature off or in conjunction with a message. See Blind Spot
Information System (page 191). See Information Messages (page 95). Brake System
It will illuminate when you engage the parking brake with the ignition on.
If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.
WARNING
Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control (If Equipped)
It will illuminate when you switch this feature on.
Direction Indicator
Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the
indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 251).
83
Fusion (CC7) , enUSA
E144524E151262E144522E71340Instrument Cluster
Door Ajar
Front Fog Lamps (If Equipped)
Displays when the ignition is on and any door is not completely closed.
Electric Park Brake
It will illuminate when the electric parking brake has a malfunction.
Engine Coolant Temperature
Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as
possible, switch off the engine and let cool. Engine Oil
If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 241). Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately. Fasten Safety Belt
It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety
Belt Minder (page 31). Front Airbag
If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer.
It will illuminate when you switch the front fog lamps on.
Heads Up Display (If Equipped) A red beam of lights will illuminate on the windshield in certain instances when using
adaptive cruise control and/or the collision warning system. It will also illuminate momentarily when you start your vehicle to make sure the display works. High Beam
It will illuminate when you switch the high beam headlamps on. It will flash when you use the
headlamp flasher. Hood Ajar
Displays when the ignition is on and the hood is not completely closed.
Lane Keeping Aid (If Equipped)
Illuminates when the lane keeping system is activated.
Low Fuel Level
It will illuminate when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as
possible. Low Tire Pressure Warning
It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check
your tire pressure as soon as possible.
84
Fusion (CC7) , enUSA
E146190E156133E159324E144813Instrument Cluster
It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer. Parking Lamps
It will illuminate when you switch the parking lamps on.
Powertrain Fault
Illuminates when a powertrain or an AWD fault has been detected. Contact your
authorized dealer as soon as possible. Service Engine Soon
If the service engine soon indicator light stays illuminated after the engine is started, it
indicates that the On Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On board diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 150). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components.
The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 150). Stability Control
It will flash when the system is active. If it remains illuminated or does not illuminate when you
switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. See Using Stability Control (page 169). Stability Control Off
It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off. See Using Stability Control (page 169). Trunk Ajar
Displays when the ignition is on and the trunk is not completely closed.
85
Fusion (CC7) , enUSA
E138639E159323Instrument Cluster
AUDIBLE WARNINGS AND INDICATORS Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position. Keyless Warning Alert (If Equipped) Sounds the horn twice when you exit your vehicle with the intelligent access key, after the last door is closed and your keyless vehicle is in RUN, indicating your vehicle is still on. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by an authorized dealer immediately.
86
Fusion (CC7) , enUSA
Information Displays
GENERAL INFORMATION
WARNING
Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.
Note: Your vehicle may or may not be equipped with all the messages listed in this chapter. Your vehicle will not display messages of systems it is not equipped with. Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display.
Information Display Controls (Type 1 and Type 2)
• Press the up and down arrow buttons
to scroll through and highlight the options within a menu.
• Press the right arrow button to enter a
sub-menu.
• Press the left arrow button to exit a
menu.
• Press and hold the left arrow button at
any time to return to the main menu display (escape button).
• Press the OK button to choose and
confirm settings or messages.
Menu You can access the menu using the information display control. Note: Some options may appear slightly different or not at all if the items are optional.
Trip Odometer Trip Timer Fuel Used Average Fuel
Fusion (CC7) , enUSA
Trip 1 and 2
87
E144637Information Displays
Trip 1 and 2
• •
All Values Outside Temperature • Resetting the Trip Computer — Press and hold OK on the current screen to reset the
respective trip, distance, time and fuel information. Trip Odometer — Registers the distance of individual journeys. Trip Timer — timer stops when the vehicle is turned off and restarts when the vehicle is restarted. Fuel Used — shows the amount of fuel used for a given trip.
• • Average Fuel — shows the average fuel economy for a given trip. • All Values — Shows all trip values. • Outside Temperature — Shows the outside air temperature.
Fuel Economy
Distance to E Inst Fuel Econ Long Term Average Fuel Fuel History All Values Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls.
Information
Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 95). All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.
88
Auto Stop/Start
MyKey System Check
Fusion (CC7) , enUSA
Information Displays
Settings
Driver Assist
Vehicle
Traction Ctrl - check enabled or uncheck disabled Blind Spot - check enabled or uncheck disabled Rear Park Aid - check enabled or uncheck disabled Hill Start Assist - check enabled or uncheck disabled Cross Traffic - check enabled or uncheck disabled Auto Engine Off - check enabled or uncheck disabled Fuel History Lighting
5, 10 or 30 minutes Autolamp Delay
Off or XX Seconds
Vehicle (cont’d)
Locks
Settings (cont’d)
Autolock - check enabled or uncheck disabled Autounlock - check enabled or uncheck disabled Relock - check enabled or uncheck disabled Mislock - check enabled or uncheck disabled Remote Unlock
All Doors or Driver First
Set to XXX %
Oil Life Rest Switch Inhibit - check enabled or uncheck disabled Windows Wipers Create MyKey 911 Assist Traction Control Max Speed Speed Minder
Remote Open or Remote Close Courtesy Wipe or Rain Sensing Hold OK to Create MyKey Always On or User Selectable Always On or User Selectable
Choose desired speed or Off Choose desired speed or Off
89
MyKey
Fusion (CC7) , enUSA
Information Displays
Volume Limiter Do Not Disturb Clear MyKeys Language Units
Settings (cont’d)
On or Off
On or Off
Hold OK to Clear All MyKeys Choose your applicable setting Distance
Temperature
Display
Choose your applicable setting Choose your applicable setting
Information Display Controls (Type 3)
Main menu From the main menu bar on the left side of the information display, you can choose from the following categories:
Display Mode
Trip 1 & 2
Fuel Economy
Information
Settings
Scroll up/down to highlight one of the categories, then press the right arrow key or OK to enter into that category. Press the left arrow key as needed to exit back to the main menu.
• Press the up and down arrow buttons
to scroll through and highlight the options within a menu.
• Press the right arrow button to enter a
sub-menu.
• Press the left arrow button to exit a
menu.
• Press and hold the left arrow button at
any time to return to the main menu display (escape button).
• Press the OK button to choose and
confirm settings or messages.
90
Fusion (CC7) , enUSA
E144638E144639E138660E144640E144642E100023Information Displays
Display Mode
Use the up/down arrow buttons to choose between the following display options.
Display mode
Option 1
Option 2
Option 3
Option 4
XXX mi (km) to empty Fuel gauge Round tachometer Vertical tachometer Engine coolant temp gauge • XXX mi (km) to empty: Shows the approximate distance the vehicle will travel. •
Fuel gauge: Indicates approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When the fuel level becomes low, the level indicator will change to amber. When the fuel level becomes critically low, the level indicator will change to red. Note: When a MyKey® is in use, low fuel warnings will display earlier. The fuel icon and arrow indicates which side of the vehicle the fuel filler door is located.
• Round tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. During SelectShift Automatic™ transmission (SST) use, the currently selected gear will appear in the display. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
•
Trip 1 & 2
Choose between the standard or enhanced trip display.
Trip 1 & 2
Standard display
Enhanced display
Trip Odometer Trip Timer Average Fuel
91
Fusion (CC7) , enUSA
E144639E138660Information Displays
Trip 1 & 2
Standard display
Enhanced display
Fuel Used Press and hold OK to reset the currently displayed trip information.
• •
Trip Odometer — shows the accumulated trip distance. Trip Timer— timer stops when the vehicle is turned off and restarts when the vehicle is restarted.
• Average Fuel — shows the average fuel economy for a given trip. •
Fuel Used — shows the amount of fuel used for a given trip.
Fuel Economy
Use the left/right arrow buttons to choose the desired fuel economy display.
Fuel Economy
Option 1
Option 2
DTE Inst Fuel Econ Average Fuel Fuel History Fuel History Duration • DTE: Distance To Empty shows the approximate distance the vehicle will travel on
5, 10, or 30 minute
the fuel remaining in the tank. Changes in driving pattern may cause the value to vary. Inst Fuel Econ: This display shows a visual graph of your instantaneous fuel economy.
• • Average Fuel: Indicates the average fuel consumption since the function was last
reset. Fuel History: shows a bar chart of your fuel history. Fuel History Duration: shows fuel usage over a 5, 10, or 30 minute time span.
• • Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls.
Info
In this mode, you can view different vehicle system information and perform a
system check.
92
Fusion (CC7) , enUSA
E144640E144642Auto Stop/Start
Driver Alert MyKey System Check
Settings
Driver Assist
Information Displays
Information
Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 95). # MyKeys and # Admin Keys Programmed All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.
Note: Some items are optional and may not appear.
In this mode, you can configure different driver setting choices.
Traction Ctrl Blindspot Collision Warning Cruise Control Cross Traffic Driver Alert Hill start
Settings On or Off On (default on key cycle) or Off Sensitivity Adaptive (default on key cycle) or Normal On (default on key cycle) or Off On or Off On or Off
High, Normal or Low
Settings (cont’d)
Driver Assist (cont’d)
Vehicle
Lane Keeping System
Front Park Aid Rear Park Aid Auto Engine Off
Alert, Aid or Both High, Normal or Low
Mode Intensity On (default on key cycle) or Off On (default on key cycle) or Off On (default on key cycle) or Off
93
Fusion (CC7) , enUSA
E100023Information Displays
Settings (cont’d)
Easy Entry/Exit Lighting
Locks
Oil Life Reset
On or Off Auto Highbeam Autolamp Delay DRL Autolock Autounlock Mislock Remote Unlocking Set to XXX % - Hold OK to Reset
Off or XX Seconds On or Off On or Off On or Off On or Off All doors or Driver’s door
Settings (cont’d)
Climate Control (using this feature allows you to select different climate control modes when the vehicle is started using the remote start feature)
Duration Quiet Start System
Heater – A/C
Steering Wheel Front Defrost Rear Defrost Driver Seat Passenger Seat 5, 10 or 15 minutes On or Off Enable or Disable
Auto or Last Settings Auto or Off Auto or Off Auto or Off Auto or Off Auto or Off
Settings (cont’d)
On or Off Remote Open Remote Close Courtesy Wipe
94
On or Off On or Off On or Off
Vehicle (cont’d)
Remote Start
Vehicle (cont’d)
Switch Inhibit Windows
Wipers
Fusion (CC7) , enUSA
Information Displays
MyKey
Display
Create MyKey 911 Assist Traction Control Max Speed Speed Minder Volume Limiter Do Not Disturb Clear MyKeys Language Units
On or Off
Settings (cont’d) Rain Sensing Hold OK to Create MyKey Always On or User Selectable Always On or User Selectable Choose desired speed or off Choose desired speed or off On or Off Always On or User Selectable Hold OK to Clear All MyKeys Choose your applicable setting - hold OK to Set Choose your applicable Distance setting Choose your applicable setting
Temperature
Gauge Display
Fuel Gauge or Fuel + Tach
INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have.
Press the OK button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time. Certain messages need to be confirmed before you can access the menus.
95
Fusion (CC7) , enUSA
E144636Information Displays
Active Park
Message
Active Park Fault
Action
Displayed when the system needs service. Contact your
authorized dealer as soon as possible.
Adaptive Cruise Control
Message
Adaptive Cruise
Malfunction
Adaptive Cruise Not
Available
Adaptive Cruise Not
Available Sensor
Blocked See Manual
Cruise Control Auto- matic Braking Turned
Off
Front Sensor Not Aligned
Adaptive Cruise - Driver
Resume Control
Adaptive Cruise Speed Too Low to Activate Adaptive Cruise Shift
Down
Action
Displayed when a radar malfunction is preventing the ACC from engaging. See Using Adaptive Cruise Control (page
180).
Displayed when conditions exist such that the adaptive cruise
cannot function properly. See Using Adaptive Cruise
Control (page 180).
Displayed when the radar is blocked because of poor radar visibility due to bad weather or ice/mud/water in front of radar. Driver can typically clean the sensor to resolve. See
Using Adaptive Cruise Control (page 180).
Displayed when the automatic braking has been disabled.
Displayed when a radar malfunction is preventing the ACC
from engaging.
Displayed when the adaptive cruise has reinstated controls
to the driver.
Displays when the vehicle speed is too slow to activate the
adaptive cruise.
Displays when the adaptive cruise is automatically adjusting the gap distance and the driver needs to shift the transmission
into a lower gear.
96
Fusion (CC7) , enUSA
Information Displays
Action
Displays when the system detects a malfunction due to a
blocked sensor.
Displayed when the traction control has been disabled or
enabled by the driver.
Action
Displays when the system detects a malfunction due to a
blocked sensor.
AdvanceTrac® Message
Service AdvanceTrac
AdvanceTrac Off On
Airbag
Message
Occupant Sensor BLOCKED Remove
Objects Near Passenger
Seat
Alarm
Message
Action
Vehicle Alarm to Stop Alarm, Start Vehicle
Displays when the alarm has been triggered due to unauthor-
ized entry. See Anti-Theft Alarm (page 63).
Auto Start-Stop
Message
Auto StartStop Press Brake to Start Engine Auto StartStop Press
Brake Harder to Activate
Auto StartStop Press Clutch to Start Engine Auto StartStop Press
Any Pedal
Auto StartStop Select Neutral To Start Engine
Action
The engine needs to be restarted, press the brake pedal to
start.
The engine needs to be restarted, press the brake pedal harder
to start.
The engine needs to be restarted, press the clutch pedal to
start.
The engine needs to be restarted, press any pedal to start.
Select neutral for the system to restart the engine.
97
Fusion (CC7) , enUSA
Information Displays
Message
Auto StartStop Shift to
P Restart Engine
Action
Select park for the system to restart the engine.
Auto StartStop Manual
Restart Required Auto StartStop Not
Available
Engine Stopped Engine Starting
Engine On due to Vehicle
Maneuvering
Engine On due to
Steering Wheel Maneuv-
ering
Engine On due to Accessory Usage
Engine On Normal Oper-
ation
The system is not functioning. A manual restart is required.
Displays when conditions are not met for the Auto StartStop system to function properly See Auto-Start-Stop (page 142).
StartStop has shutoff the engine automatically. StartStop is starting the engine automatically.
The wheels are at a sharp angle or the steering wheel is being
turned.
The wheels are at a sharp angle or the steering wheel is being
turned.
Engine may be on to support high demand for electrical
accessories, such as operating power windows, rear defroster,
or when using the power point.
Engine is on to support normal vehicle operation. Includes external vehicle conditions, such as altitude, traffic, low
ambient temperature. Also includes battery outside optimal operating conditions (state of charge and temperature), and
inadequate brake vacuum (can occur if the brake pedal is
depressed a number of times in succession).
Engine On due to Low
Temperature
Engine On due to Outside Air Temp
Engine On due to Engine
Warming
Engine On due to
Selected Gear
Engine On due to Steep
Grade
Engine On due to Key not
Detected
Engine is on in order to increase the engine temperature to an
acceptable level.
Engine is on to support normal vehicle operation due to low
outside ambient temperature.
Engine is on in order to increase the engine temperature to an
acceptable level.
Engine is on due to a low gear selection by the transmission.
Engine is on due to a steep road grade.
Engine is on due to no key being detected by the vehicle.
98
Fusion (CC7) , enUSA
Information Displays
Action
Engine is on due to the driver door being opened.
Engine is on due to the driver seat belt being unbuckled.
Engine is on to achieve or maintain interior compartment at
an acceptable level.
Engine is on, which is required to support the use of the power
outlet (110V).
Engine is on due to the vehicle battery needing to be charged.
Select neutral and release the clutch for the system to restart
the engine.
Message
Engine On due to Driver
Door Opened
Engine On due to Driver
Belt Unbuckled Engine On due to Heating /Cooling
Engine On due to Power
Outlet in Use
Engine On due to Vehicle
Charging
Select Neutral and
Release Clutch to Auto-
Stop
Deactivated by Driver
Displays when the Start Stop feature has been disabled by
the driver.
Automatic Engine Shutdown
Message
Engine Shuts Off in XX
Seconds
Engine Shut Off for Fuel
Economy
Engine Shuts Off in XX Seconds Press Ok to
Override
Action
Displays when the engine is getting ready to shut off.
Displays when the engine has shut off to help increase fuel
economy.
Displays when the engine is getting ready to shut off. You can press OK on the left steering wheel button to override the shut
down.
99
Fusion (CC7) , enUSA
AWD
Message
AWD Temporarily
Disabled AWD Off
AWD Restored
AWD Malfunction Service Required
Information Displays
Action
Displayed when the AWD system has been temporarily
disabled to protect itself from overheating.
Displayed when the AWD system has been automatically disabled to protect itself. This is caused by operating the
vehicle with the compact spare tire installed or if the system
is overheating.
The AWD system will resume normal function and clear this message after driving a short distance with the road tire re-
installed or after the system is allowed to cool.
Displayed in conjunction with the Throttle Control/Transmis- sion/AWD light when the AWD system is not operating prop- erly. If the warning stays on or continues to come on, contact
your authorized dealer as soon as possible.
Battery and Charging System
Message
Check Charging System
Low Battery Features Temporarily Turned Off
Turn Power Off to Save
Battery
Action
Displayed when the charging system needs servicing. If the
warning stays on or continues to come on, contact your
authorized dealer as soon as possible.
Displayed when the battery management system detects an extended low-voltage condition. Various vehicle features will be disabled to help preserve the battery. Turn off as many of the electrical loads as soon as possible to improve system voltage. If the system voltage has recovered, the disabled
features will operate again as normal
Displayed when the battery management system determines that the battery is at a low state of charge. Turn the ignition off as soon as possible to protect the battery. This message will clear once the vehicle has been started and the battery state of charge has recovered. Turning off unnecessary elec- trical loads will allow faster battery state-of-charge recovery.
100
Fusion (CC7) , enUSA
Information Displays
Blind Spot Information and Cross Traffic Alert System
Message
Action
Blindspot System Fault
Displayed when a fault with the system has occurred. Contact
your authorized dealer as soon as possible.
Blindspot Not Available
Sensor Blocked See
Manual
Displayed when the system sensors are blocked. Contact your
authorized dealer as soon as possible. See Blind Spot
Information System (page 191).
Cross Traffic Vehicle
Coming From X
Displayed when the system detects a vehicle. See Blind Spot
Information System (page 191).
Cross Traffic Not Avail- able Sensor Blocked See
Manual
Displayed when the blind spot information system and cross
traffic alert system sensors are blocked. See Blind Spot
Information System (page 191).
Cross Traffic System
Fault
Displays when a fault with the system has occurred. Contact
your authorized dealer as soon as possible.
Collision Warning System
Message
Collision Warning
Malfunction
Collision Warning Not
Available Sensor
Blocked See Manual
Action
Displayed when there is a system malfunction with the colli- sion warning system. The system will be disabled. Contact
your authorized dealer as soon as possible.
Displayed when the collision warning system radar is blocked because of poor radar visibility due to bad weather or ice/ mud/water in front of the radar. Driver can typically clean the sensor to resolve. Contact your authorized dealer as soon as
possible.
Collision Warning Not
Available
Displayed when there is a system malfunction with the colli- sion warning system. The system will be disabled. Contact
your authorized dealer as soon as possible.
101
Fusion (CC7) , enUSA
Information Displays
Action
Displays when the door(s) listed is not completely closed and
the vehicle is moving.
Displays when the door(s) listed is not completely closed. Displays when the luggage compartment is not completely
closed.
Displays when the hood is not completely closed.
Displays when the door switches have been disabled.
Displayed when there is a system malfunction with the child locks. Contact your authorized dealer as soon as possible. Displays the factory keypad code after the keypad has been
reset.
Action
Stop and rest as soon as it is safe to do so.
Take a rest break soon.
Action
Doors and Locks
Message X Door Ajar
Trunk ajar
Hood ajar
Switches Inhibited
Security Mode
Child Lock Malfunction
Service Required
Factory Keypad Code
XXXXX
Driver Alert
Message
Driver Alert Warning Rest
Now
Driver Alert Warning Rest
Suggested
Fuel
Message
Fuel Level Low
Displayed as an early reminder of a low fuel condition.
Check Fuel Fill Inlet
Displayed when the fuel fill inlet may not be properly closed.
Hill Start Assist
Message
Action
Hill Start Assist Not
Available
Displays when hill start assist is not available. Contact your
authorized dealer. See Hill Start Assist (page 166).
102
Fusion (CC7) , enUSA
Information Displays
Keys and Intelligent Access
Message
Press Brake to START
No Key Detected
Restart Now or Key is
Needed
Action
Displayed as a reminder to press the brake while starting the
vehicle.
Displayed if the key is not detected by the system. See
Keyless Starting (page 136).
Displayed when the StartStop button is pressed to shut off the engine and an Intelligent Access key is not detected inside
the vehicle.
Run Power Active
Displayed when the vehicle is in the run ignition state.
Starting System Fault
This message is displayed when there is a problem with your
vehicle’s starting system. See your authorized dealer for
service.
Press Brake and Clutch
to Start
Press Clutch to Start
Key Program Successful
Key Program Failure
Displayed as a reminder to press the brake and clutch while
starting the vehicle.
Displayed as a reminder to press the clutch in while starting
the vehicle.
Displayed during spare key programming, when an intelligent
access key is programmed to the system.
Displayed during spare key programming, when an intelligent
access key has failed to be programmed.
Max Number of Keys
Learned
Displayed during spare key programming when the maximum
number of keys have been programmed.
Not Enough Keys
Learned
Displayed during spare key programming when not enough
keys have been programmed.
Key Battery Low Replace
Soon
Could Not Program
Integrated Key
Engine On
Displays when the key battery is low. Change the battery as
soon as possible.
Displayed when an attempt is made to program a spare key
using two existing keys.
Displays to inform the driver that they are exiting the vehicle
and the engine is on.
103
Fusion (CC7) , enUSA
Information Displays
Lane Keeping System
Message
Lane Keeping Sys. Malfunction Service
Required
Action
The system has malfunctioned. Contact your authorized
dealer as soon as possible.
Front Camera Tempor-
arily Not Available
The system has detected a condition that has caused the
system to be temporarily unavailable.
Front Camera Low Visib-
ility Clean Screen
The system has detected a condition that requires the wind-
shield to be cleaned to operate properly.
Front Camera Malfunc- tion Service Required Keep Hands on Steering
Wheel
The system has malfunctioned. Contact your authorized
dealer as soon as possible.
Displayed when the system requests the driver to keep their
hands on the steering wheel.
Maintenance Message
LOW Engine Oil Pressure
Action
Stop the vehicle as soon as safely possible, turn off the engine.
Check the oil level. If the warning stays on or continues to come on with your engine running, contact your authorized
dealer as soon as possible.
Change Engine Oil Soon
Displayed when the engine oil life remaining is 10% or less.
See Engine Oil Check (page 241).
Oil Change Required
Brake Fluid Level LOW
Check Brake System
Engine Coolant Overtem-
perature
Displayed when the oil life left reaches 0%. See Engine Oil
Check (page 241).
Indicates the brake fluid level is low and the brake system should be inspected immediately. See Brake and Clutch
Fluid Check (page 245).
Displays when the brake system needs servicing. Stop the
vehicle in a safe place. Contact your authorized dealer.
Displays when the engine temperature is too high. Stop the vehicle in a safe place and allow the engine to cool. If the problem persists, contact your authorized dealer. See Engine
Coolant Check (page 242).
104
Fusion (CC7) , enUSA
Information Displays
Message
Power Reduced to Lower Engine Temp Transport / Factory
Mode
See Manual
Action
Displays when the engine has reduced power in order to help
reduce high coolant temperatures.
Displays to indicate that the vehicle is still in Transport or Factory mode. This may not allow some features to operate
properly. See your authorized dealer.
Informs the driver that the powertrain needs service due to a
powertrain malfunction.
MyKey
Message
MyKey Not Created
MyKey Active Drive
Safely
Speed Limited to XX
MPH/km/h
Near Vehicle Top Speed
Vehicle at Top Speed of
MyKey Setting
Check Speed Drive
Safely
Buckle Up to Unmute
Audio
AdvanceTrac On -
MyKey Setting
Traction Control On -
MyKey Setting
MyKey Park Aid Cannot
be Deactivated
Lane Keeping Alert On
MyKey Setting
Action
Displayed during key programming when MyKey cannot be
programmed.
Displays when MyKey is active.
Displays when starting the vehicle and MyKey is in use and
the MyKey speed limit is on.
Displays when a MyKey is in use and the MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h). Displays when a MyKey is in use and the MyKey speed limit is
reached.
Displays when MyKey is active.
Displays when a MyKey is in use and Belt-Minder is activated.
Displays when a MyKey is in use and AdvanceTrac is activated.
Displays when a MyKey is in use and Traction control is
activated.
Displays when a MyKey is in use and park aid is activated.
Displayed when the lane keeping aid is on per MyKey settings.
105
Fusion (CC7) , enUSA
Information Displays
Action
Displays when the system has detected a condition that
requires service. Contact your authorized dealer. See Parking
Aid (page 170).
Displays when the system has detected a condition that
requires service. Contact your authorized dealer. See Parking
Aid (page 170).
Displays the park aid status. Displays the park aid status.
Action
Displays when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h). If the warning stays on after the parking brake is released, contact
your authorized dealer.
The electric parking brake system has detected a condition
that requires service. See your authorized dealer. Displays when the electric parking brake is not set.
Displays when the electric parking brake is running a diagnostic
check.
Displays when the electric parking brake is set but has not be
released.
Displays when the electric parking brake is set but has not be
released and the vehicle is moving.
The electric park brake system has detected a condition that
requires service. See your authorized dealer.
Displays when the electric parking brake was not released
causing it to overheat.
Park Aid
Message
Check Front Park Aid
Check Rear Park Aid
Front Park Aid On Off Rear Park Aid On Off
Park Brake
Message
Park Brake Engaged
Park Brake Malfunction
Service Now
Park Brake Not Applied
Apply Park Brake
Park Brake Maintenance
Mode
Park Brake Use Switch
to Release
Press Brake to Release Park Brake and Switch
Park Brake Limited Function Service
Required
Park Brake System
Overheated
106
Fusion (CC7) , enUSA
Information Displays
Message
Release Park Brake
Action
Displays when the electric parking brake is set and the vehicle
is started.
Park Brake Applied Park Brake Released
Displays when the electric parking brake is set.
Displays when the electric parking brake is released.
Power Steering Message
Action
Steering Fault Service
Now
The power steering system has detected a condition that
requires service. See your authorized dealer.
Steering Loss Stop
Safely
The power steering system is not working. Stop the vehicle a
safe place. Contact your authorized dealer.
Steering Assist Fault
Service Required
The power steering system has detected a condition within the power steering system or passive entry or passive start system requires service. Contact your authorized dealer.
Remote Start Message
Action
To Drive: Turn Key to On
Displays as a reminder to turn the key on to drive the vehicle
after a remote start.
To Drive: Press Brake
and Start Button
Displays as a reminder to apply the brake and the start button
to drive the vehicle after a remote start.
Seats
Message
Memory Recall Not
Permitted While Driving
Action
Displays as a reminder that memory seats are not available
while driving.
Memory X Saved
Displays to show where your memory setting has been saved.
107
Fusion (CC7) , enUSA
Information Displays
Starting System
Message
Press Brake to Start
Engine Start Pending
Please Wait
Pending Start Cancelled Cranking Time Exceeded
Action
Displays when starting the vehicle as a reminder to apply the
brake.
Displays when the starter is attempting to start the vehicle.
Displays when the pending start has been cancelled.
Displays when the starter has exceeded its cranking time in
attempting to start the vehicle.
Tire Pressure Monitoring System
Message
LOW Tire Pressure
Tire Pressure Monitor
Fault
Tire Pressure Sensor
Fault
Traction Control
Message
Traction Control Off / Traction Control On Spinout Detected Hazards Activated
Action
Displays when one or more tires on your vehicle have low tire pressure. See Tire Pressure Monitoring System (page 279).
malfunctioning. If the warning stays on or continues to come
Displays when the tire pressure monitoring system is on, contact your authorized dealer. See Tire Pressure
Monitoring System (page 279).
Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, See Tire Pressure Monitoring System (page 279). If the warning stays on or continues to come on, contact your authorized dealer as soon
as possible.
Action
Displays when the traction control system has been switched
off or on. See Using Traction Control (page 168).
Displays when a spinout has occurred and the hazard are
activated.
108
Fusion (CC7) , enUSA
Information Displays
Action
See your authorized dealer.
The transmission is overheating and needs to cool. Stop in a
safe place as soon as it is possible.
The transmission has overheated and needs to cool. Stop in
a safe place as soon as it is possible.
See your authorized dealer.
Transmission is getting hot. Stop to let it cool.
Displays when the transmission has overheated and has
limited functionality. See Automatic Transmission (page
154).
Transmission is too cold. Wait for it to warm up before you
drive.
Displays as a reminder to shift into park.
Displays as a reminder to press the brake pedal in order to
select a gear.
Displays when the transmission has adjusted the shift
strategy.
Displays when the transmission is adjusting the shift strategy.
Displays when the transmission shift lever is locked and unable
to select gears.
Displays when the transmission shift lever is unlocked and
free to select gears.
Transmission Message
Transmission Malfunc-
tion Service Now Transmission Over- heating Stop Safely
Transmission Overtem- perature Stop Safely Transmission Service
Required
Transmission Too Hot
Press Brake
Transmission Limited Function See Manual
Transmission Warming
Up Please Wait
Transmission Not in Park
Press Brake Pedal
Transmission Adjusted
Transmission Adapt
Mode
Transmission Indicate
Mode Lockup On
Transmission Indicate
Mode Lockup Off
109
Fusion (CC7) , enUSA
Climate Control
MANUAL CLIMATE CONTROL (IF EQUIPPED)