Download PDF Manual

Fuel Gauge Engine Coolant Temperature Gauge


Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled.


Outside Air Temperature Shows the outside air temperature. Compass Displays the vehicle’s heading direction. Trip Computer See General Information (page 87).


80


Fusion (CC7) , enUSA


E144485 Instrument Cluster


Vehicle Settings and Personalization See General Information (page 87). Engine Coolant Temperature Gauge Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the center section. If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down. Note: Do not restart the engine until the cause of overheating has been resolved.


WARNING


Never remove the coolant reservoir cap while the engine is running or hot.


Fuel Gauge Note: The fuel gauge may vary slightly when your vehicle is moving or on a gradient.


Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. The needle should move toward F when you refuel your vehicle. If the needle points to E after adding fuel, this indicates your vehicle needs service soon. After refueling some variability in needle position is normal: •


It may take a short time for the needle to reach F after leaving the gas station. This is normal and depends upon the slope of pavement at the gas station. The fuel amount dispensed into the tank is a little less or more than the gauge indicated. This is normal and depends upon the slope of pavement at the gas station. If the gas station nozzle shuts off before the tank is full, try a different gas pump nozzle. Low Fuel Reminder A low fuel reminder triggers when the fuel gauge needle is at 1/16th.




Variations:


Driving type (fuel economy


conditions)


Highway driving


Severe duty driving (trailer


towing, extended idle)


Fuel gauge position


Distance-to-empty


1/16th


1/16th


35 miles to 80 miles (56 km


to 129 km)


35 miles (56km)


81


Fusion (CC7) , enUSA


Instrument Cluster


Type 3


Left Information Display Speedometer Right Information Display See General Information (page 87).


Left Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. Trip Computer See General Information (page 87). Vehicle Settings and Personalization See General Information (page 87).


WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.


82


Fusion (CC7) , enUSA


E144486 Instrument Cluster


Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle. Adaptive Cruise Control (If Equipped)


The speed control system indicator light changes color to indicate what mode the system is in: See Using Cruise Control (page 179). On (white light): Illuminates when the adaptive cruise control system is turned on. Turns off when the speed control system is turned off. Engaged (green light): Illuminates when the adaptive cruise control system is engaged. Turns off when the speed control system is disengaged. Anti-Lock Braking System


If it illuminates when you are driving, this indicates a malfunction. You will continue


to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer. Auto Start-stop (If Equipped)


It will illuminate to inform you when the engine shuts down or in conjunction with a message.


Battery


If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical


equipment and have the system checked by your authorized dealer immediately.


Blind Spot Monitor (If Equipped)


It will illuminate when you switch this feature off or in conjunction with a message. See Blind Spot


Information System (page 191). See Information Messages (page 95). Brake System


It will illuminate when you engage the parking brake with the ignition on.


If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.


WARNING


Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control (If Equipped)


It will illuminate when you switch this feature on.


Direction Indicator


Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the


indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 251).


83


Fusion (CC7) , enUSA


E144524E151262E144522E71340 Instrument Cluster


Door Ajar


Front Fog Lamps (If Equipped)


Displays when the ignition is on and any door is not completely closed.


Electric Park Brake


It will illuminate when the electric parking brake has a malfunction.


Engine Coolant Temperature


Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as


possible, switch off the engine and let cool. Engine Oil


If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 241). Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately. Fasten Safety Belt


It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety


Belt Minder (page 31). Front Airbag


If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer.


It will illuminate when you switch the front fog lamps on.


Heads Up Display (If Equipped) A red beam of lights will illuminate on the windshield in certain instances when using


adaptive cruise control and/or the collision warning system. It will also illuminate momentarily when you start your vehicle to make sure the display works. High Beam


It will illuminate when you switch the high beam headlamps on. It will flash when you use the


headlamp flasher. Hood Ajar


Displays when the ignition is on and the hood is not completely closed.


Lane Keeping Aid (If Equipped)


Illuminates when the lane keeping system is activated.


Low Fuel Level


It will illuminate when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as


possible. Low Tire Pressure Warning


It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check


your tire pressure as soon as possible.


84


Fusion (CC7) , enUSA


E146190E156133E159324E144813 Instrument Cluster


It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer. Parking Lamps


It will illuminate when you switch the parking lamps on.


Powertrain Fault


Illuminates when a powertrain or an AWD fault has been detected. Contact your


authorized dealer as soon as possible. Service Engine Soon


If the service engine soon indicator light stays illuminated after the engine is started, it


indicates that the On Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On board diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 150). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components.


The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 150). Stability Control


It will flash when the system is active. If it remains illuminated or does not illuminate when you


switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. See Using Stability Control (page 169). Stability Control Off


It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off. See Using Stability Control (page 169). Trunk Ajar


Displays when the ignition is on and the trunk is not completely closed.


85


Fusion (CC7) , enUSA


E138639E159323 Instrument Cluster


AUDIBLE WARNINGS AND INDICATORS Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position. Keyless Warning Alert (If Equipped) Sounds the horn twice when you exit your vehicle with the intelligent access key, after the last door is closed and your keyless vehicle is in RUN, indicating your vehicle is still on. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by an authorized dealer immediately.


86


Fusion (CC7) , enUSA


Information Displays


GENERAL INFORMATION


WARNING


Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.


Note: Your vehicle may or may not be equipped with all the messages listed in this chapter. Your vehicle will not display messages of systems it is not equipped with. Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display.


Information Display Controls (Type 1 and Type 2)


• Press the up and down arrow buttons


to scroll through and highlight the options within a menu.


• Press the right arrow button to enter a


sub-menu.


• Press the left arrow button to exit a


menu.


• Press and hold the left arrow button at


any time to return to the main menu display (escape button).


• Press the OK button to choose and


confirm settings or messages.


Menu You can access the menu using the information display control. Note: Some options may appear slightly different or not at all if the items are optional.


Trip Odometer Trip Timer Fuel Used Average Fuel


Fusion (CC7) , enUSA


Trip 1 and 2


87


E144637 Information Displays


Trip 1 and 2


• •


All Values Outside Temperature • Resetting the Trip Computer — Press and hold OK on the current screen to reset the


respective trip, distance, time and fuel information. Trip Odometer — Registers the distance of individual journeys. Trip Timer — timer stops when the vehicle is turned off and restarts when the vehicle is restarted. Fuel Used — shows the amount of fuel used for a given trip.


• • Average Fuel — shows the average fuel economy for a given trip. • All Values — Shows all trip values. • Outside Temperature — Shows the outside air temperature.


Fuel Economy


Distance to E Inst Fuel Econ Long Term Average Fuel Fuel History All Values Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls.


Information


Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 95). All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.


88


Auto Stop/Start


MyKey System Check


Fusion (CC7) , enUSA


Information Displays


Settings


Driver Assist


Vehicle


Traction Ctrl - check enabled or uncheck disabled Blind Spot - check enabled or uncheck disabled Rear Park Aid - check enabled or uncheck disabled Hill Start Assist - check enabled or uncheck disabled Cross Traffic - check enabled or uncheck disabled Auto Engine Off - check enabled or uncheck disabled Fuel History Lighting


5, 10 or 30 minutes Autolamp Delay


Off or XX Seconds


Vehicle (cont’d)


Locks


Settings (cont’d)


Autolock - check enabled or uncheck disabled Autounlock - check enabled or uncheck disabled Relock - check enabled or uncheck disabled Mislock - check enabled or uncheck disabled Remote Unlock


All Doors or Driver First


Set to XXX %


Oil Life Rest Switch Inhibit - check enabled or uncheck disabled Windows Wipers Create MyKey 911 Assist Traction Control Max Speed Speed Minder


Remote Open or Remote Close Courtesy Wipe or Rain Sensing Hold OK to Create MyKey Always On or User Selectable Always On or User Selectable


Choose desired speed or Off Choose desired speed or Off


89


MyKey


Fusion (CC7) , enUSA


Information Displays


Volume Limiter Do Not Disturb Clear MyKeys Language Units


Settings (cont’d)


On or Off


On or Off


Hold OK to Clear All MyKeys Choose your applicable setting Distance


Temperature


Display


Choose your applicable setting Choose your applicable setting


Information Display Controls (Type 3)


Main menu From the main menu bar on the left side of the information display, you can choose from the following categories:


Display Mode


Trip 1 & 2


Fuel Economy


Information


Settings


Scroll up/down to highlight one of the categories, then press the right arrow key or OK to enter into that category. Press the left arrow key as needed to exit back to the main menu.


• Press the up and down arrow buttons


to scroll through and highlight the options within a menu.


• Press the right arrow button to enter a


sub-menu.


• Press the left arrow button to exit a


menu.


• Press and hold the left arrow button at


any time to return to the main menu display (escape button).


• Press the OK button to choose and


confirm settings or messages.


90


Fusion (CC7) , enUSA


E144638E144639E138660E144640E144642E100023 Information Displays


Display Mode


Use the up/down arrow buttons to choose between the following display options.


Display mode


Option 1


Option 2


Option 3


Option 4


XXX mi (km) to empty Fuel gauge Round tachometer Vertical tachometer Engine coolant temp gauge • XXX mi (km) to empty: Shows the approximate distance the vehicle will travel. •


Fuel gauge: Indicates approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When the fuel level becomes low, the level indicator will change to amber. When the fuel level becomes critically low, the level indicator will change to red. Note: When a MyKey® is in use, low fuel warnings will display earlier. The fuel icon and arrow indicates which side of the vehicle the fuel filler door is located.


• Round tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. During SelectShift Automatic™ transmission (SST) use, the currently selected gear will appear in the display. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.



Trip 1 & 2


Choose between the standard or enhanced trip display.


Trip 1 & 2


Standard display


Enhanced display


Trip Odometer Trip Timer Average Fuel


91


Fusion (CC7) , enUSA


E144639E138660 Information Displays


Trip 1 & 2


Standard display


Enhanced display


Fuel Used Press and hold OK to reset the currently displayed trip information.


• •


Trip Odometer — shows the accumulated trip distance. Trip Timer— timer stops when the vehicle is turned off and restarts when the vehicle is restarted.


• Average Fuel — shows the average fuel economy for a given trip. •


Fuel Used — shows the amount of fuel used for a given trip.


Fuel Economy


Use the left/right arrow buttons to choose the desired fuel economy display.


Fuel Economy


Option 1


Option 2


DTE Inst Fuel Econ Average Fuel Fuel History Fuel History Duration • DTE: Distance To Empty shows the approximate distance the vehicle will travel on


5, 10, or 30 minute


the fuel remaining in the tank. Changes in driving pattern may cause the value to vary. Inst Fuel Econ: This display shows a visual graph of your instantaneous fuel economy.


• • Average Fuel: Indicates the average fuel consumption since the function was last


reset. Fuel History: shows a bar chart of your fuel history. Fuel History Duration: shows fuel usage over a 5, 10, or 30 minute time span.


• • Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls.


Info


In this mode, you can view different vehicle system information and perform a


system check.


92


Fusion (CC7) , enUSA


E144640E144642 Auto Stop/Start


Driver Alert MyKey System Check


Settings


Driver Assist


Information Displays


Information


Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 95). # MyKeys and # Admin Keys Programmed All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.


Note: Some items are optional and may not appear.


In this mode, you can configure different driver setting choices.


Traction Ctrl Blindspot Collision Warning Cruise Control Cross Traffic Driver Alert Hill start


Settings On or Off On (default on key cycle) or Off Sensitivity Adaptive (default on key cycle) or Normal On (default on key cycle) or Off On or Off On or Off


High, Normal or Low


Settings (cont’d)


Driver Assist (cont’d)


Vehicle


Lane Keeping System


Front Park Aid Rear Park Aid Auto Engine Off


Alert, Aid or Both High, Normal or Low


Mode Intensity On (default on key cycle) or Off On (default on key cycle) or Off On (default on key cycle) or Off


93


Fusion (CC7) , enUSA


E100023 Information Displays


Settings (cont’d)


Easy Entry/Exit Lighting


Locks


Oil Life Reset


On or Off Auto Highbeam Autolamp Delay DRL Autolock Autounlock Mislock Remote Unlocking Set to XXX % - Hold OK to Reset


Off or XX Seconds On or Off On or Off On or Off On or Off All doors or Driver’s door


Settings (cont’d)


Climate Control (using this feature allows you to select different climate control modes when the vehicle is started using the remote start feature)


Duration Quiet Start System


Heater – A/C


Steering Wheel Front Defrost Rear Defrost Driver Seat Passenger Seat 5, 10 or 15 minutes On or Off Enable or Disable


Auto or Last Settings Auto or Off Auto or Off Auto or Off Auto or Off Auto or Off


Settings (cont’d)


On or Off Remote Open Remote Close Courtesy Wipe


94


On or Off On or Off On or Off


Vehicle (cont’d)


Remote Start


Vehicle (cont’d)


Switch Inhibit Windows


Wipers


Fusion (CC7) , enUSA


Information Displays


MyKey


Display


Create MyKey 911 Assist Traction Control Max Speed Speed Minder Volume Limiter Do Not Disturb Clear MyKeys Language Units


On or Off


Settings (cont’d) Rain Sensing Hold OK to Create MyKey Always On or User Selectable Always On or User Selectable Choose desired speed or off Choose desired speed or off On or Off Always On or User Selectable Hold OK to Clear All MyKeys Choose your applicable setting - hold OK to Set Choose your applicable Distance setting Choose your applicable setting


Temperature


Gauge Display


Fuel Gauge or Fuel + Tach


INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have.


Press the OK button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time. Certain messages need to be confirmed before you can access the menus.


95


Fusion (CC7) , enUSA


E144636 Information Displays


Active Park


Message


Active Park Fault


Action


Displayed when the system needs service. Contact your


authorized dealer as soon as possible.


Adaptive Cruise Control


Message


Adaptive Cruise


Malfunction


Adaptive Cruise Not


Available


Adaptive Cruise Not


Available Sensor


Blocked See Manual


Cruise Control Auto- matic Braking Turned


Off


Front Sensor Not Aligned


Adaptive Cruise - Driver


Resume Control


Adaptive Cruise Speed Too Low to Activate Adaptive Cruise Shift


Down


Action


Displayed when a radar malfunction is preventing the ACC from engaging. See Using Adaptive Cruise Control (page


180).


Displayed when conditions exist such that the adaptive cruise


cannot function properly. See Using Adaptive Cruise


Control (page 180).


Displayed when the radar is blocked because of poor radar visibility due to bad weather or ice/mud/water in front of radar. Driver can typically clean the sensor to resolve. See


Using Adaptive Cruise Control (page 180).


Displayed when the automatic braking has been disabled.


Displayed when a radar malfunction is preventing the ACC


from engaging.


Displayed when the adaptive cruise has reinstated controls


to the driver.


Displays when the vehicle speed is too slow to activate the


adaptive cruise.


Displays when the adaptive cruise is automatically adjusting the gap distance and the driver needs to shift the transmission


into a lower gear.


96


Fusion (CC7) , enUSA


Information Displays


Action


Displays when the system detects a malfunction due to a


blocked sensor.


Displayed when the traction control has been disabled or


enabled by the driver.


Action


Displays when the system detects a malfunction due to a


blocked sensor.


AdvanceTrac® Message


Service AdvanceTrac


AdvanceTrac Off On


Airbag


Message


Occupant Sensor BLOCKED Remove


Objects Near Passenger


Seat


Alarm


Message


Action


Vehicle Alarm to Stop Alarm, Start Vehicle


Displays when the alarm has been triggered due to unauthor-


ized entry. See Anti-Theft Alarm (page 63).


Auto Start-Stop


Message


Auto StartStop Press Brake to Start Engine Auto StartStop Press


Brake Harder to Activate


Auto StartStop Press Clutch to Start Engine Auto StartStop Press


Any Pedal


Auto StartStop Select Neutral To Start Engine


Action


The engine needs to be restarted, press the brake pedal to


start.


The engine needs to be restarted, press the brake pedal harder


to start.


The engine needs to be restarted, press the clutch pedal to


start.


The engine needs to be restarted, press any pedal to start.


Select neutral for the system to restart the engine.


97


Fusion (CC7) , enUSA


Information Displays


Message


Auto StartStop Shift to


P Restart Engine


Action


Select park for the system to restart the engine.


Auto StartStop Manual


Restart Required Auto StartStop Not


Available


Engine Stopped Engine Starting


Engine On due to Vehicle


Maneuvering


Engine On due to


Steering Wheel Maneuv-


ering


Engine On due to Accessory Usage


Engine On Normal Oper-


ation


The system is not functioning. A manual restart is required.


Displays when conditions are not met for the Auto StartStop system to function properly See Auto-Start-Stop (page 142).


StartStop has shutoff the engine automatically. StartStop is starting the engine automatically.


The wheels are at a sharp angle or the steering wheel is being


turned.


The wheels are at a sharp angle or the steering wheel is being


turned.


Engine may be on to support high demand for electrical


accessories, such as operating power windows, rear defroster,


or when using the power point.


Engine is on to support normal vehicle operation. Includes external vehicle conditions, such as altitude, traffic, low


ambient temperature. Also includes battery outside optimal operating conditions (state of charge and temperature), and


inadequate brake vacuum (can occur if the brake pedal is


depressed a number of times in succession).


Engine On due to Low


Temperature


Engine On due to Outside Air Temp


Engine On due to Engine


Warming


Engine On due to


Selected Gear


Engine On due to Steep


Grade


Engine On due to Key not


Detected


Engine is on in order to increase the engine temperature to an


acceptable level.


Engine is on to support normal vehicle operation due to low


outside ambient temperature.


Engine is on in order to increase the engine temperature to an


acceptable level.


Engine is on due to a low gear selection by the transmission.


Engine is on due to a steep road grade.


Engine is on due to no key being detected by the vehicle.


98


Fusion (CC7) , enUSA


Information Displays


Action


Engine is on due to the driver door being opened.


Engine is on due to the driver seat belt being unbuckled.


Engine is on to achieve or maintain interior compartment at


an acceptable level.


Engine is on, which is required to support the use of the power


outlet (110V).


Engine is on due to the vehicle battery needing to be charged.


Select neutral and release the clutch for the system to restart


the engine.


Message


Engine On due to Driver


Door Opened


Engine On due to Driver


Belt Unbuckled Engine On due to Heating /Cooling


Engine On due to Power


Outlet in Use


Engine On due to Vehicle


Charging


Select Neutral and


Release Clutch to Auto-


Stop


Deactivated by Driver


Displays when the Start Stop feature has been disabled by


the driver.


Automatic Engine Shutdown


Message


Engine Shuts Off in XX


Seconds


Engine Shut Off for Fuel


Economy


Engine Shuts Off in XX Seconds Press Ok to


Override


Action


Displays when the engine is getting ready to shut off.


Displays when the engine has shut off to help increase fuel


economy.


Displays when the engine is getting ready to shut off. You can press OK on the left steering wheel button to override the shut


down.


99


Fusion (CC7) , enUSA


AWD


Message


AWD Temporarily


Disabled AWD Off


AWD Restored


AWD Malfunction Service Required


Information Displays


Action


Displayed when the AWD system has been temporarily


disabled to protect itself from overheating.


Displayed when the AWD system has been automatically disabled to protect itself. This is caused by operating the


vehicle with the compact spare tire installed or if the system


is overheating.


The AWD system will resume normal function and clear this message after driving a short distance with the road tire re-


installed or after the system is allowed to cool.


Displayed in conjunction with the Throttle Control/Transmis- sion/AWD light when the AWD system is not operating prop- erly. If the warning stays on or continues to come on, contact


your authorized dealer as soon as possible.


Battery and Charging System


Message


Check Charging System


Low Battery Features Temporarily Turned Off


Turn Power Off to Save


Battery


Action


Displayed when the charging system needs servicing. If the


warning stays on or continues to come on, contact your


authorized dealer as soon as possible.


Displayed when the battery management system detects an extended low-voltage condition. Various vehicle features will be disabled to help preserve the battery. Turn off as many of the electrical loads as soon as possible to improve system voltage. If the system voltage has recovered, the disabled


features will operate again as normal


Displayed when the battery management system determines that the battery is at a low state of charge. Turn the ignition off as soon as possible to protect the battery. This message will clear once the vehicle has been started and the battery state of charge has recovered. Turning off unnecessary elec- trical loads will allow faster battery state-of-charge recovery.


100


Fusion (CC7) , enUSA


Information Displays


Blind Spot Information and Cross Traffic Alert System


Message


Action


Blindspot System Fault


Displayed when a fault with the system has occurred. Contact


your authorized dealer as soon as possible.


Blindspot Not Available


Sensor Blocked See


Manual


Displayed when the system sensors are blocked. Contact your


authorized dealer as soon as possible. See Blind Spot


Information System (page 191).


Cross Traffic Vehicle


Coming From X


Displayed when the system detects a vehicle. See Blind Spot


Information System (page 191).


Cross Traffic Not Avail- able Sensor Blocked See


Manual


Displayed when the blind spot information system and cross


traffic alert system sensors are blocked. See Blind Spot


Information System (page 191).


Cross Traffic System


Fault


Displays when a fault with the system has occurred. Contact


your authorized dealer as soon as possible.


Collision Warning System


Message


Collision Warning


Malfunction


Collision Warning Not


Available Sensor


Blocked See Manual


Action


Displayed when there is a system malfunction with the colli- sion warning system. The system will be disabled. Contact


your authorized dealer as soon as possible.


Displayed when the collision warning system radar is blocked because of poor radar visibility due to bad weather or ice/ mud/water in front of the radar. Driver can typically clean the sensor to resolve. Contact your authorized dealer as soon as


possible.


Collision Warning Not


Available


Displayed when there is a system malfunction with the colli- sion warning system. The system will be disabled. Contact


your authorized dealer as soon as possible.


101


Fusion (CC7) , enUSA


Information Displays


Action


Displays when the door(s) listed is not completely closed and


the vehicle is moving.


Displays when the door(s) listed is not completely closed. Displays when the luggage compartment is not completely


closed.


Displays when the hood is not completely closed.


Displays when the door switches have been disabled.


Displayed when there is a system malfunction with the child locks. Contact your authorized dealer as soon as possible. Displays the factory keypad code after the keypad has been


reset.


Action


Stop and rest as soon as it is safe to do so.


Take a rest break soon.


Action


Doors and Locks


Message X Door Ajar


Trunk ajar


Hood ajar


Switches Inhibited


Security Mode


Child Lock Malfunction


Service Required


Factory Keypad Code


XXXXX


Driver Alert


Message


Driver Alert Warning Rest


Now


Driver Alert Warning Rest


Suggested


Fuel


Message


Fuel Level Low


Displayed as an early reminder of a low fuel condition.


Check Fuel Fill Inlet


Displayed when the fuel fill inlet may not be properly closed.


Hill Start Assist


Message


Action


Hill Start Assist Not


Available


Displays when hill start assist is not available. Contact your


authorized dealer. See Hill Start Assist (page 166).


102


Fusion (CC7) , enUSA


Information Displays


Keys and Intelligent Access


Message


Press Brake to START


No Key Detected


Restart Now or Key is


Needed


Action


Displayed as a reminder to press the brake while starting the


vehicle.


Displayed if the key is not detected by the system. See


Keyless Starting (page 136).


Displayed when the StartStop button is pressed to shut off the engine and an Intelligent Access key is not detected inside


the vehicle.


Run Power Active


Displayed when the vehicle is in the run ignition state.


Starting System Fault


This message is displayed when there is a problem with your


vehicle’s starting system. See your authorized dealer for


service.


Press Brake and Clutch


to Start


Press Clutch to Start


Key Program Successful


Key Program Failure


Displayed as a reminder to press the brake and clutch while


starting the vehicle.


Displayed as a reminder to press the clutch in while starting


the vehicle.


Displayed during spare key programming, when an intelligent


access key is programmed to the system.


Displayed during spare key programming, when an intelligent


access key has failed to be programmed.


Max Number of Keys


Learned


Displayed during spare key programming when the maximum


number of keys have been programmed.


Not Enough Keys


Learned


Displayed during spare key programming when not enough


keys have been programmed.


Key Battery Low Replace


Soon


Could Not Program


Integrated Key


Engine On


Displays when the key battery is low. Change the battery as


soon as possible.


Displayed when an attempt is made to program a spare key


using two existing keys.


Displays to inform the driver that they are exiting the vehicle


and the engine is on.


103


Fusion (CC7) , enUSA


Information Displays


Lane Keeping System


Message


Lane Keeping Sys. Malfunction Service


Required


Action


The system has malfunctioned. Contact your authorized


dealer as soon as possible.


Front Camera Tempor-


arily Not Available


The system has detected a condition that has caused the


system to be temporarily unavailable.


Front Camera Low Visib-


ility Clean Screen


The system has detected a condition that requires the wind-


shield to be cleaned to operate properly.


Front Camera Malfunc- tion Service Required Keep Hands on Steering


Wheel


The system has malfunctioned. Contact your authorized


dealer as soon as possible.


Displayed when the system requests the driver to keep their


hands on the steering wheel.


Maintenance Message


LOW Engine Oil Pressure


Action


Stop the vehicle as soon as safely possible, turn off the engine.


Check the oil level. If the warning stays on or continues to come on with your engine running, contact your authorized


dealer as soon as possible.


Change Engine Oil Soon


Displayed when the engine oil life remaining is 10% or less.


See Engine Oil Check (page 241).


Oil Change Required


Brake Fluid Level LOW


Check Brake System


Engine Coolant Overtem-


perature


Displayed when the oil life left reaches 0%. See Engine Oil


Check (page 241).


Indicates the brake fluid level is low and the brake system should be inspected immediately. See Brake and Clutch


Fluid Check (page 245).


Displays when the brake system needs servicing. Stop the


vehicle in a safe place. Contact your authorized dealer.


Displays when the engine temperature is too high. Stop the vehicle in a safe place and allow the engine to cool. If the problem persists, contact your authorized dealer. See Engine


Coolant Check (page 242).


104


Fusion (CC7) , enUSA


Information Displays


Message


Power Reduced to Lower Engine Temp Transport / Factory


Mode


See Manual


Action


Displays when the engine has reduced power in order to help


reduce high coolant temperatures.


Displays to indicate that the vehicle is still in Transport or Factory mode. This may not allow some features to operate


properly. See your authorized dealer.


Informs the driver that the powertrain needs service due to a


powertrain malfunction.


MyKey


Message


MyKey Not Created


MyKey Active Drive


Safely


Speed Limited to XX


MPH/km/h


Near Vehicle Top Speed


Vehicle at Top Speed of


MyKey Setting


Check Speed Drive


Safely


Buckle Up to Unmute


Audio


AdvanceTrac On -


MyKey Setting


Traction Control On -


MyKey Setting


MyKey Park Aid Cannot


be Deactivated


Lane Keeping Alert On


MyKey Setting


Action


Displayed during key programming when MyKey cannot be


programmed.


Displays when MyKey is active.


Displays when starting the vehicle and MyKey is in use and


the MyKey speed limit is on.


Displays when a MyKey is in use and the MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h). Displays when a MyKey is in use and the MyKey speed limit is


reached.


Displays when MyKey is active.


Displays when a MyKey is in use and Belt-Minder is activated.


Displays when a MyKey is in use and AdvanceTrac is activated.


Displays when a MyKey is in use and Traction control is


activated.


Displays when a MyKey is in use and park aid is activated.


Displayed when the lane keeping aid is on per MyKey settings.


105


Fusion (CC7) , enUSA


Information Displays


Action


Displays when the system has detected a condition that


requires service. Contact your authorized dealer. See Parking


Aid (page 170).


Displays when the system has detected a condition that


requires service. Contact your authorized dealer. See Parking


Aid (page 170).


Displays the park aid status. Displays the park aid status.


Action


Displays when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h). If the warning stays on after the parking brake is released, contact


your authorized dealer.


The electric parking brake system has detected a condition


that requires service. See your authorized dealer. Displays when the electric parking brake is not set.


Displays when the electric parking brake is running a diagnostic


check.


Displays when the electric parking brake is set but has not be


released.


Displays when the electric parking brake is set but has not be


released and the vehicle is moving.


The electric park brake system has detected a condition that


requires service. See your authorized dealer.


Displays when the electric parking brake was not released


causing it to overheat.


Park Aid


Message


Check Front Park Aid


Check Rear Park Aid


Front Park Aid On Off Rear Park Aid On Off


Park Brake


Message


Park Brake Engaged


Park Brake Malfunction


Service Now


Park Brake Not Applied


Apply Park Brake


Park Brake Maintenance


Mode


Park Brake Use Switch


to Release


Press Brake to Release Park Brake and Switch


Park Brake Limited Function Service


Required


Park Brake System


Overheated


106


Fusion (CC7) , enUSA


Information Displays


Message


Release Park Brake


Action


Displays when the electric parking brake is set and the vehicle


is started.


Park Brake Applied Park Brake Released


Displays when the electric parking brake is set.


Displays when the electric parking brake is released.


Power Steering Message


Action


Steering Fault Service


Now


The power steering system has detected a condition that


requires service. See your authorized dealer.


Steering Loss Stop


Safely


The power steering system is not working. Stop the vehicle a


safe place. Contact your authorized dealer.


Steering Assist Fault


Service Required


The power steering system has detected a condition within the power steering system or passive entry or passive start system requires service. Contact your authorized dealer.


Remote Start Message


Action


To Drive: Turn Key to On


Displays as a reminder to turn the key on to drive the vehicle


after a remote start.


To Drive: Press Brake


and Start Button


Displays as a reminder to apply the brake and the start button


to drive the vehicle after a remote start.


Seats


Message


Memory Recall Not


Permitted While Driving


Action


Displays as a reminder that memory seats are not available


while driving.


Memory X Saved


Displays to show where your memory setting has been saved.


107


Fusion (CC7) , enUSA


Information Displays


Starting System


Message


Press Brake to Start


Engine Start Pending


Please Wait


Pending Start Cancelled Cranking Time Exceeded


Action


Displays when starting the vehicle as a reminder to apply the


brake.


Displays when the starter is attempting to start the vehicle.


Displays when the pending start has been cancelled.


Displays when the starter has exceeded its cranking time in


attempting to start the vehicle.


Tire Pressure Monitoring System


Message


LOW Tire Pressure


Tire Pressure Monitor


Fault


Tire Pressure Sensor


Fault


Traction Control


Message


Traction Control Off / Traction Control On Spinout Detected Hazards Activated


Action


Displays when one or more tires on your vehicle have low tire pressure. See Tire Pressure Monitoring System (page 279).


malfunctioning. If the warning stays on or continues to come


Displays when the tire pressure monitoring system is on, contact your authorized dealer. See Tire Pressure


Monitoring System (page 279).


Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, See Tire Pressure Monitoring System (page 279). If the warning stays on or continues to come on, contact your authorized dealer as soon


as possible.


Action


Displays when the traction control system has been switched


off or on. See Using Traction Control (page 168).


Displays when a spinout has occurred and the hazard are


activated.


108


Fusion (CC7) , enUSA


Information Displays


Action


See your authorized dealer.


The transmission is overheating and needs to cool. Stop in a


safe place as soon as it is possible.


The transmission has overheated and needs to cool. Stop in


a safe place as soon as it is possible.


See your authorized dealer.


Transmission is getting hot. Stop to let it cool.


Displays when the transmission has overheated and has


limited functionality. See Automatic Transmission (page


154).


Transmission is too cold. Wait for it to warm up before you


drive.


Displays as a reminder to shift into park.


Displays as a reminder to press the brake pedal in order to


select a gear.


Displays when the transmission has adjusted the shift


strategy.


Displays when the transmission is adjusting the shift strategy.


Displays when the transmission shift lever is locked and unable


to select gears.


Displays when the transmission shift lever is unlocked and


free to select gears.


Transmission Message


Transmission Malfunc-


tion Service Now Transmission Over- heating Stop Safely


Transmission Overtem- perature Stop Safely Transmission Service


Required


Transmission Too Hot


Press Brake


Transmission Limited Function See Manual


Transmission Warming


Up Please Wait


Transmission Not in Park


Press Brake Pedal


Transmission Adjusted


Transmission Adapt


Mode


Transmission Indicate


Mode Lockup On


Transmission Indicate


Mode Lockup Off


109


Fusion (CC7) , enUSA


Climate Control


MANUAL CLIMATE CONTROL (IF EQUIPPED)


Loading...
x