2014 Ford Fusion Owners Manual

The safety belt pretensioners and optional rear inflatable safety belts are designed to activate in frontal, near-frontal and side crashes. The knee airbag(s) may deploy based on crash severity and occupant conditions. The design of the side airbags and side curtain airbags is to inflate in certain side impact crashes. Side airbags and side curtain airbags may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation.

•

•

•

42

Supplementary Restraints System

AIRBAG DISPOSAL Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.

43

Fusion (CC7) , enUSA

Keys and Remote Controls

•

Intelligent Access (If Equipped) The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met: You touch the inside of the front • exterior door handle. You press the luggage compartment button. • You press a button on the transmitter. If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote Control (page 44). REMOTE CONTROL Integrated Keyhead Transmitters (If Equipped) Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control.

Press the button to release the key. Press and hold the button to fold the key back in when not in use.

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. The typical operating range for your transmitter is approximately 33 feet (10
meters). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range: • weather conditions nearby radio towers • structures around the vehicle • other vehicles parked next to your • vehicle

The radio frequency used by your remote control can also be used by other short distance radio transmissions, for example amateur radios, medical equipment, wireless headphones, remote controls and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key. Note: Make sure to lock your vehicle before leaving it unattended. Note: If you are in range, the remote control will operate if you press any button unintentionally.

44

Fusion (CC7) , enUSA

E151797Keys and Remote Controls

Note: Your vehicle’s keys came with a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference. Intelligent Access Key (If Equipped)

Slide the release on the back of the remote control and pivot the cover off to access the key blade.

Your intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to activate the push-button start system. Removable Key Blade The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door.

Note: Your vehicle’s backup keys came with a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference. Using the Key Blade The key cylinder is under a cap on the driver door handle. To remove the cap:

45

Fusion (CC7) , enUSA

E151795E144506E151796E151795E151956Keys and Remote Controls

1.

Insert the key blade into the slot on the bottom of the handle and press up. 2. While maintaining upward pressure, move the cap rearward to release it. Gently remove the key while doing so.

To install the cap:

Integrated Keyhead Transmitter The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent. Press the button to release the key before beginning the procedure.

1.

Insert a screwdriver in the position shown and gently push the clip.

2. Press the clip down to release the

battery cover.

3. Carefully remove the cover.

1. Place the cap just forward of the key

cylinder.

2. While applying pressure to the cap,

move it forward until it is in place. You may hear a snap as it engages.

Make sure you have properly installed the cap by trying to move it rearward. Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally. A message will appear in the information display when the remote control battery is low. See Information Messages (page 95).

46

Fusion (CC7) , enUSA

E151957E151798E151799Keys and Remote Controls

Note: Do not touch the battery contacts or the printed circuit board with the screwdriver. 4.

Insert a screwdriver as shown to release the battery.

1. Slide the release on the back of the

remote control and pivot the cover off.

2.

Insert a coin into the slot and twist to separate the housing.

5. Remove the battery. 6.

Install a new battery with the + facing up.

7. Replace the battery cover. Intelligent Access Transmitter The remote control uses two coin-type three-volt lithium batteries CR2025 or equivalent.

47

Fusion (CC7) , enUSA

3. Remove the batteries. 4.

Install new batteries with the + facing each other.

Note: Make sure to replace the label between the two batteries.

E151801E151796E153890E153891Keys and Remote Controls

Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems. The remote start system will not work if: • • • • • • • Remote Control Feedback An LED on the remote control provides status feedback of remote start or stop commands.

the ignition is on the alarm system triggered you disable the feature the hood is open the transmission is not in P the vehicle battery voltage is too low the service engine soon light is on.

LED

Solid green

Solid red

Status

Remote start or

extension successful Remote stop

successful; engine

off

Blinking red

Blinking green

Remote start or

stop failed

Waiting for status

update

Remote Starting the Vehicle Note: You must press each button within three seconds of each other. Your vehicle will not remote start if you do not follow this sequence.

5. Reinstall the housing and cover. Car Finder

Press the button twice within three seconds. The horn will sound and the turn signals will flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm. Sounding a Panic Alarm Note: The panic alarm will only operate when the ignition is off.

Press the button to activate the alarm. Press the button again or switch the ignition on to

deactivate. Remote Start (If Equipped) WARNING

To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well

ventilated.

Note: Do not use remote start if your vehicle is low on fuel.

The remote start button is on the transmitter.

This feature allows you to start your vehicle from outside the vehicle. The transmitter has an extended operating range. Vehicles with automatic climate control can be configured to operate when the vehicle is remote started. See Climate Control (page 110). A manual climate control system will run at the setting it was set to when you switched the vehicle off.

48

Fusion (CC7) , enUSA

E138623E138624E138625Keys and Remote Controls

Extending the Vehicle Run Time Repeat Steps 1 and 2 with the vehicle still running to extend the run time for another remote start duration. If you programmed the duration to last 10 minutes, the second 10 minutes will begin after what is left of the first activation time. For example, if the vehicle had been running from the first remote start for five minutes, the vehicle will continue to run now for a total of 15
minutes. You can extend the remote start up to a maximum of 35 minutes. Wait at least five seconds before remote starting after a vehicle shutdown. Turning the Vehicle Off After Remote Starting

Press the button once. The parking lamps will turn off. You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running vehicle. You can disable or enable the remote start system through the information display. See General Information (page 87).

REPLACING A LOST KEY OR REMOTE CONTROL Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle. See Passive Anti-Theft System (page 61). To re-program the passive anti-theft system see an authorized dealer.

The tag with your transmitter details the starting procedure. To remote start your vehicle: 1. Press the lock button to lock all the

doors.

2. Press the remote start button twice. The exterior lamps will flash twice.

The horn will sound if the system fails to start, unless quiet start is on. Quiet start will run the blower fan at a slower speed to reduce noise. It can be switched on or off in the information display. See General Information (page 87). Note: If the vehicle has been remote started with an integrated keyhead transmitter, you must switch the ignition on before driving your vehicle. With an intelligent access transmitter, you must press the START/STOP button on the instrument panel once while applying the brake pedal before driving your vehicle. The power windows will not work during the remote start and the radio will not turn on automatically. The parking lamps will remain on and the vehicle will run for 5, 10, or 15 minutes, depending on the setting.

49

Fusion (CC7) , enUSA

E138626E138625MyKey™

PRINCIPLE OF OPERATION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys. These can be used to: • • • When you have programmed a MyKey, you can access the following information using the information display: • How many admin keys and MyKeys are

create a MyKey program configurable MyKey settings clear all MyKey features.

programmed to your vehicle. The total distance your vehicle has traveled using a MyKey.

Note: All MyKeys are programmed to the same settings. You cannot program them individually. Note: For vehicles with intelligent access with push-button start, when both a MyKey and an admin intelligent access key fob are present, the admin fob will be recognized by the vehicle while switching the ignition on to start the vehicle. Non-configurable Settings The following settings cannot be changed by an admin key user:

•

•

•

Belt-Minder. You cannot disable this feature. The audio system will mute when the front seat occupants’ safety belts are not fastened. Early low fuel. The low-fuel warning activates earlier, giving the MyKey user more time to refuel.

• Driver assist features, if equipped on

your vehicle, are forced on: parking aid, blind spot information system (BLIS) with cross traffic alert, lane departure warning and forward collision warning system.

Configurable Settings With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the vehicle. You can also change the settings afterward with an admin key. • A vehicle speed limit can be set.

Warnings will be shown in the display followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal or by setting cruise control.

• Vehicle speed minders of 45, 55 or 65
mph (75, 90 or 105 km/h). Once you select a speed, it will be shown in the display, followed by an audible tone when the preselected vehicle speed is exceeded.

• Audio system maximum volume of

45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled.

• Always on setting. When this is

selected, you will not be able to turn off Advance Trac (if your vehicle is equipped with this feature).

50

Fusion (CC7) , enUSA

MyKey™

CREATING A MYKEY Use the information display to create a MyKey: 1. Insert the key you want to program into the ignition. If your vehicle is equipped with a push-button start, place the intelligent access key fob into the backup slot. The location of your backup slot is in another chapter. See Starting and Stopping the Engine (page 136). 2. Switch the ignition on. 3. Access the main menu on the information display controls, and select Settings then MyKey by pressing OK or the > button. 4. Press OK or the > button to select Create MyKey. 5. When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at the next start. MyKey is successfully created. Make sure you label it so you can distinguish it from the admin keys. You can also program configurable settings for the key(s). See Programming/Changing Configurable Settings. Programming/Changing Configurable Settings Use the information display to access your configurable MyKey settings. 1. Switch the ignition on using an admin

key or fob.

2. Access the main menu on the

information display controls, and select Settings, then MyKey by pressing OK or > button.

3. Use the arrow buttons to get to a

feature.

Fusion (CC7) , enUSA

4. Press OK or > to make a selection. Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you have switched the vehicle off, however, you will need an admin key to change or clear your MyKey settings. CLEARING ALL MYKEYS You can clear all MyKeys within the same key cycle as you created the MyKey. If you switch your ignition off, however, you will need to use an admin key to clear your MyKeys. Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status at once. To clear all MyKeys of all MyKey settings, use the information display to do the following: 1. Access the main menu and select

Settings, then MyKey.

2. Scroll to Clear MyKey and press the

OK button.

3. Hold the OK button until ALL MYKEYS CLEARED displays.

CHECKING MYKEY SYSTEM STATUS You can find information about your programmed MyKeys by using the information display. MYKEY DISTANCE Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear your MyKey. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey.

51

MyKey™

USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system.

NUMBER OF MYKEY(S) Indicates the number of MyKeys programmed to your vehicle. Use this feature to detect how many MyKeys you have for your vehicle and determine when a MyKey has been deleted. NUMBER OF ADMIN KEY(S) Indicates how many admin keys are programmed to your vehicle. Use this feature to determine how many unrestricted keys you have for your vehicle, and detect if an additional MyKey has been programmed. MYKEY TROUBLESHOOTING

Condition I cannot create a MyKey.

I cannot program the configurable settings.

I cannot clear the MyKeys.

Fusion (CC7) , enUSA

Potential Causes

· The key or fob used to start the vehicle does not have admin privileges. · The key or fob used to start the vehicle is the only admin key (there always has to be at least one admin key). · Vehicles with push-button start: The intelli- gent access key fob is not positioned correctly next to the steering column. See Keyless Starting (page 136). · SecuriLock passive anti-theft system is disabled or in unlimited mode. · The vehicle has been started using a remote start system that is not programmed with admin privileges. See Using MyKey With Remote Start Systems (page 52). · The key or fob used to start your vehicle does not have admin privileges. · No MyKeys are created. See Creating a MyKey (page 51). · The vehicle has been started using a remote start system that is not programmed with admin privileges. See Using MyKey With Remote Start Systems (page 52). · The key or fob used to start your vehicle does not have admin privileges.

52

MyKey™

Condition

Potential Causes

· No MyKeys are created. See Creating a MyKey (page 51). · The vehicle has been started using a remote start system that is not programmed with admin privileges. See Using MyKey With Remote Start Systems (page 52). Purchase a new key from your authorized dealer. Program a spare key. See Passive Anti-Theft System (page 61). · The vehicle has a remote start system that is recognized as an admin key. Clear all MyKeys by using the remote start. See Using MyKey With Remote Start Systems (page 52). · The vehicle's system does not recognize any programmed MyKeys. See Creating a MyKey (page 51). · An unknown key or fob has been created as a MyKey. · The vehicle has a remote start system. See Using MyKey With Remote Start Systems (page 52). · An unknown key or fob has been programmed to the vehicle as an admin key. · The vehicle has a remote start system. See Using MyKey With Remote Start Systems (page 52). · The MyKey user is not using the MyKey. · An admin key holder cleared the MyKeys and created new MyKeys. · The key system has been reset. · An admin fob is present at vehicle start. · No MyKeys are created. See Creating a MyKey (page 51).

I lost the only admin key.

I lost a key

I accidentally programmed all keys as MyKeys.

MyKey total includes one additional key.

Admin key total includes one additional key.

MyKey distances do not accumulate.

No MyKey functions with the Intelligent Access key.

53

Fusion (CC7) , enUSA

Locks

Remote Control You can use the remote control at any time. The luggage compartment release button will only work when the vehicle speed is less than 5 mph (8 km/h). Unlocking the Doors (Two-Stage Unlock)

Press the button to unlock the driver door. Press the button again within

three seconds to unlock all doors. The turn signals will flash. Press and hold both the lock and unlock buttons on the remote control for three seconds to change between driver door or all doors unlock mode. The turn signals will flash twice to indicate a change to the unlocking mode. Driver door unlock mode will only unlock the driver door when the unlock button is pressed once. All door unlock mode will unlock all doors with one press of the unlock button. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access. You can also change the mode in the information display. See General Information (page 87). Locking the Doors

Press the button to lock all the doors. The turn signals will illuminate.

Press the button again within three seconds to confirm that all the doors are closed. The doors will lock again, the horn will sound and the turn signals will illuminate if all the doors and the luggage compartment are closed.

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lock and unlock the vehicle. Power Door Locks The power door lock control is on the driver and front passenger door panels.

Unlock Lock

Door Lock Indicator An LED on each door window trim will light when you lock the door. It will remain lit for up to 10 minutes after you switch off the ignition. Switch Inhibitor When you electronically lock your vehicle, the power door lock switch will no longer operate after 20 seconds. You must unlock your vehicle with the remote control or keyless keypad, or switch the ignition on, to restore function to these switches. You can switch this feature on or off in the information display. See General Information (page 87). Rear Door Unlocking and Opening Pull the interior door release handle twice to unlock and open the rear door. The first pull unlocks the door and the second pull will unlatch the door.

54

Fusion (CC7) , enUSA

E138628E138629E138623Locks

Note: Keep the door handle surface clean to avoid issues with operation. At the Luggage Compartment

Press the exterior release button hidden above the license plate. Smart Unlocks For Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition. When you open one of the front doors and lock the vehicle with the power door lock control, all the doors will lock then unlock and the horn will sound twice if your key is still in the ignition. You can still lock your vehicle with the key in the ignition. To do this, use the keyless entry keypad with the driver door closed, or press the lock button on the transmitter even if the doors are not closed. If both front doors are closed, you can lock your vehicle by any method, regardless of whether the key is in the ignition or not. Smart Unlocks For Intelligent Access Keys (If Equipped) This feature helps to prevent you from unintentionally locking your intelligent access key inside your vehicle’s passenger compartment or rear cargo area.

Mislock If any door or the luggage compartment is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn will sound twice and the lamps will not flash. You can enable or disable this feature in the information display. See General Information (page 87). Opening the Luggage Compartment

Press twice within three seconds to open the luggage compartment.

Make sure to close and latch the luggage compartment before driving your vehicle. An unlatched luggage compartment may cause objects to fall out or block your view. Activating Intelligent Access (If Equipped) You must have the intelligent access key within 3 feet (1 meter) of your vehicle. At a Door Pull an exterior door handle to unlock and open the door. Make sure not to touch the lock sensor on top of the handle.

Touch the top of the door handle to lock your vehicle. There will be a brief delay before you can unlock your vehicle again.

55

Fusion (CC7) , enUSA

E138630E157085E144402Locks

•

•

you shift into any gear putting your vehicle in motion, and your vehicle attains a speed greater than 12 mph (20 km/h).

The autolock feature repeats when: •

you open then close any door while the ignition is on and your vehicle speed is 9 mph (15 km/h) or lower, and your vehicle then attains a speed greater than 12 mph (20 km/h).

•

Autounlock Feature The autounlock feature will unlock all the doors when: •

the ignition is on, all the doors are closed, and your vehicle has been in motion at a speed greater than 12 mph (20 km/h); your vehicle comes to a stop and you switch the ignition off or to accessory; and you open the driver door within 10
minutes of the switching the ignition off or to accessory.

•

•

Note: The doors will not autounlock if you electronically lock your vehicle after you switch the ignition off and before you open the driver door. Enabling or Disabling Note: You can enable or disable the autolock and autounlock features independently of each other. You can enable or disable these features in the information display or your authorized dealer can do it for you. See General Information (page 87). Illuminated Entry The interior lamps and select exterior lamps will illuminate when you unlock the doors with the remote entry system.

When you electronically lock your vehicle (with any door open, vehicle in park and ignition off), the vehicle will search for an intelligent access key in the passenger compartment after you close the last door. If your vehicle finds a key, all of the doors will immediately unlock and the horn will sound twice, indicating that a key is inside. You can override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle. To do this, lock your vehicle after you have closed all the doors by: • •

using the keyless entry keypad pressing the lock button on another intelligent access key touching the locking area on the handle with another intelligent access key in your hand.

•

When you open one of the front doors and lock your vehicle using the power door lock control, all doors will lock then unlock if: • •

the ignition is on, or the ignition is off and your vehicle is not in P.

Auto Relock If you press the unlock button on the remote control and do not open a door within 45 seconds, your vehicle will lock and the alarm will arm. You can enable or disable this feature in the information display. See General Information (page 87). Autolock Feature The autolock feature will lock all the doors when: • •

all doors are closed, the ignition is on,

56

Fusion (CC7) , enUSA

Locks

Luggage Compartment With the Remote Control

Press twice within three seconds to unlatch the trunk.

From Outside Your Vehicle

Press the release button above the license plate to unlatch the trunk. Your vehicle must be unlocked or have an intelligent access transmitter within 3 feet (1 meter) of the trunk. KEYLESS ENTRY (IF EQUIPPED) SECURICODE™ KEYLESS ENTRY KEYPAD The keypad is located near the driver window. It is invisible until touched and then it lights up so you can see and touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more slowly.

The illuminated entry system will turn off the lights if: • •

the ignition is on, you press the remote control lock button, or after 25 seconds of illumination.

• The lights will not turn off if: •

you turn them on with the lamp control, or • any door is open. Illuminated Exit The interior lamps and select exterior lamps will illuminate when all doors are closed, you switch the ignition off and you remove the key from the ignition (integrated keyhead transmitter only). The lamps will turn off if all the doors remain closed and: • •

25 seconds elapse you insert the key in the ignition (integrated keyhead transmitter only) you press the START/STOP button (intelligent access key only).

•

Battery Saver If you leave the courtesy lamps, dome lamps or headlamps on, the battery saver will shut them off 10 minutes after you switch the ignition off. Accessory Mode Battery Saver for Intelligent Access Keys (If Equipped) If you leave your vehicle in the run ignition state, it will shut off once it detects a certain amount of battery drain or after 45
minutes.

57

Fusion (CC7) , enUSA

E138630E144402Locks

The doors will lock then unlock to confirm that programming was successful. To program additional personal entry codes, repeat Steps 1-3, then for Step 4: press 3·4 to save personal code 2
• press 5·6 to save personal code 3
• press 7·8 to save personal code 4
• press 9·0 to save personal code 5. • You may also program a personal entry code through the MyFord Touch system (if equipped). Tips: • Do not set a code that uses five of the

same number.

• Do not use five numbers in sequential

order. The factory-set code will work even if you have set your own personal code.

•

•

•

Recalling Memory Positions (If Equipped) The programmed entry codes will recall driver memory positions as follows: •

Entry code 1 will recall driver 1 memory positions. Entry code 2 will recall driver 2 memory positions. Entry code 3 will recall driver 3 memory positions.

Note: Personal entry codes 4 and 5 will not recall memory positions. Erasing a Personal Code 1. Enter the factory-set 5-digit code. 2. Press and release 1·2 on the keypad

within five seconds.

3. Press and hold 1·2 for two seconds. You must do this within five seconds of completing Step 2.

All personal codes are now erased and only the factory-set 5–digit code will work.

58

You can use the keypad to: lock or unlock the doors • • release the trunk recall memory seat and mirror • positions (if equipped) program and erase user codes arm and disarm the anti-theft alarm.

• • You can operate the keypad with the factory-set 5-digit entry code. The code is located on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also create up to five of your own 5-digit personal entry codes. Programming a Personal Entry Code To create your own personal entry code: 1. Enter the factory-set code. 2. Press 1·2 on the keypad within five

seconds.

3. Enter your personal 5-digit code. You must enter each number within five seconds of each other.

4. Press 1·2 on the keypad to save

personal code 1.

Fusion (CC7) , enUSA

E138637Locks

Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • •

one minute of keypad inactivity pressing the unlock button on the remote control switching the ignition on unlocking your vehicle using intelligent access.

• •

Unlocking and Locking the Doors To Unlock the Driver Door Enter the factory-set 5-digit code or your personal code. You must press each number within five seconds of each other. The interior lamps will illuminate. Note: All doors will unlock if you enable the all-door unlocking mode. See Locking and Unlocking (page 54). To Unlock All Doors Enter the factory-set code or your personal code, then press 3·4 within five seconds. To Lock All Doors Press and hold 7·8 and 9·0 at the same time (with the driver door closed). You do not need to enter the keypad code first. To Release the Trunk Enter the factory-set code or your personal code, then press 5·6 within five seconds. Displaying the Factory Set Code With Integrated Keyhead Transmitters Note: You will need to have two programmed passive anti-theft keys for this procedure.

Fusion (CC7) , enUSA

To display the factory-set code in the information display: 1.

Insert a key into the ignition and switch the ignition on for a few seconds.

2. Switch the ignition off and remove the

key. Insert the second key into the ignition and switch the ignition on.

3.

The factory-set code will display for a few seconds. Note: The code may not display until after any other warning messages first display. With Intelligent Access Keys Note: You will need to have two programmed intelligent access keys for this procedure. To display the factory-set code in the information display:

1. Place the first programmed key in the backup slot inside the center console. The key ring must be at the top with the buttons facing toward the rear.

2. Press the START/STOP button once

and wait a few seconds.

3. Press the START/STOP button again

and remove the key. Insert the second programmed key into the backup slot, then press the START/STOP button.

4.

59

E147165Locks

The factory-set code will appear in the information display for a few seconds. Note: The code may not display until after any other warning messages first display. INTERIOR LUGGAGE COMPARTMENT RELEASE

WARNINGS

Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a

child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.

Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the

temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

Your vehicle is equipped with a release handle that provides a means of escape for children and adults if they become locked inside the luggage compartment. Adults should familiarize themselves with the operation and location of the release handle.

The handle is located inside the luggage compartment either on the luggage compartment door (lid) or near the tail lamps. It is composed of a material that will glow for hours in darkness following brief exposure to ambient light. Pull the handle and push up on the luggage compartment door (lid) to open from within the luggage compartment.

60

Fusion (CC7) , enUSA

E144403Security

PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting problems if they are too close to the key when starting your vehicle. Prevent these objects from touching the coded key while starting your vehicle. Switch the ignition off, move all objects on the key chain away from the coded key and restart your vehicle if a problem occurs. Note: Do not leave a duplicate coded key in your vehicle. Always take your keys and lock all doors when leaving your vehicle. SecuriLock® The system helps prevent your vehicle from starting unless you use a coded key programmed to your vehicle. Using the wrong key may prevent your vehicle from starting. A message may appear in the information display. If you are unable to start your vehicle with a correctly coded key, a malfunction has happened. A message may appear in the information display. Automatic Arming Your vehicle arms immediately after switching the ignition off. Automatic Disarming Switching the ignition on with a coded key disarms your vehicle.

Replacement Keys Note: Your vehicle comes equipped with two integrated keyhead transmitters or two intelligent access keys. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control. The intelligent access key functions as a programmed key that operates the driver door lock and activates the intelligent access with push button start system, as well as a remote control. If your programmed transmitters or standard SecuriLock coded keys (integrated keyhead transmitters only) are lost or stolen and you do not have an extra coded key, you will need to have your vehicle towed to an authorized dealer. You need to erase the key codes from your vehicle and program new coded keys. Store an extra programmed key away from your vehicle in a safe place to help prevent any inconveniences. See your authorized dealer to purchase additional spare or replacement keys. Programming a Spare Integrated Keyhead Transmitter Note: You can program a maximum of eight coded keys to your vehicle. All eight can be integrated keyhead transmitters. You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure will program both the vehicle immobilizer keycode and the remote entry portion of the remote control to your vehicle. Only use integrated keyhead transmitters or standard SecuriLock keys.

61

Fusion (CC7) , enUSA

Security

Programming a Spare Intelligent Access Key Note: You can program a maximum for four intelligent access keys to your vehicle. You must have two previously programmed intelligent access keys inside your vehicle and the new unprogrammed intelligent access keys readily accessible. See an authorized dealer to have the spare key programmed if two previously programmed keys are not available. Make sure that your vehicle is off before beginning this procedure. Make sure that you close all the doors before beginning and that they remain closed throughout the procedure. Perform all steps within 30
seconds of starting the sequence. Stop and wait for at least one minute before starting again if you perform any steps out of sequence. Read and understand the entire procedure before you begin.

1. Place a programmed intelligent access

key in the backup slot in the center console. The key ring must be at the top with the buttons facing toward the rear.

2. Wait 5 seconds, and then press the

START/STOP button.

3. Remove the intelligent access key.

You must have two previously programmed coded keys and the new unprogrammed key readily accessible. See an authorized dealer to have the spare key programmed if two previously programmed coded keys are not available. Read and understand the entire procedure before you begin. 1.

Insert the first previously programmed coded key into the ignition.

2. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds. 3. Switch the ignition off and remove the

first coded key from the ignition. 4. After three seconds but within 10

seconds of switching the ignition off, insert the second previously coded key into the ignition.

5. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds. 6. Switch the ignition off and remove the second previously programmed coded key from the ignition.

7. After three seconds but within 10

seconds of switching the ignition off and removing the previously programmed coded key, insert the new unprogrammed key into the ignition.

8. Switch the ignition from off to on. Keep the ignition on for at least six seconds. 9. Remove the newly programmed coded

key from the ignition.

If the key has been successfully programmed it will start your vehicle and operate the remote entry system (if the new key is an integrated keyhead transmitter). If programming was not successful, wait 10 seconds and repeat Steps 1 through 8. If you are still unsuccessful, take your vehicle to an authorized dealer.

62

Fusion (CC7) , enUSA

E147165Security

• Unlock the doors or luggage

compartment with the remote control or keyless entry keypad. Switch the ignition on or start the vehicle.

•

• Use a key in the driver’s door to unlock the vehicle, then switch the ignition on within 12 seconds.

Note: Pressing the panic button on the remote control will stop the horn and signal indicators, but will not disarm the system.

4. Within 10 seconds, place a second

programmed intelligent access key in the backup slot and press the START/STOP button.

5. Wait 5 seconds, and then press the

START/STOP button again.

6. Remove the intelligent access key. 7. Wait 5 seconds, then place the

unprogrammed intelligent access key in the backup slot and press the START/STOP button.

Programming is now complete. Verify the remote control functions operate and your vehicle starts with the new intelligent access key. If programming was not successful, wait 10 seconds and repeat Steps 1 through 7. If you are still unsuccessful, take your vehicle to your authorized dealer. ANTI-THEFT ALARM The system will warn you of an unauthorized entry to your vehicle. It will be triggered if any door, the luggage compartment or the hood is opened without using the key, remote control or keyless entry keypad. The direction indicators will flash and the horn will sound if unauthorized entry is attempted while the alarm is armed. Take all remote controls to an authorized dealer if there is any potential alarm problem with your vehicle. Arming the Alarm The alarm is ready to arm when there is not a key in the ignition. Electronically lock the vehicle to arm the alarm. Disarming the Alarm Disarm the alarm by any of the following actions:

63

Fusion (CC7) , enUSA

Steering Wheel

ADJUSTING THE STEERING WHEEL

WARNING

Do not adjust the steering wheel when your vehicle is moving.

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 121).

Volume up Volume down Mute Media Seek down or previous Seek up or next

1. Unlock the steering column. 2. Adjust the steering wheel to the desired

position.

MEDIA Press repeatedly to scroll through available audio sources. Seek, Next or Previous Press the seek button to: •

tune the radio to the next or previous stored preset play the next or the previous track.

• Press and hold the seek button to: •

tune the radio to the next station up or down the frequency band seek through a track.

•

64

3. Lock the steering column. AUDIO CONTROL (IF EQUIPPED) You can operate the following functions with the control:

Fusion (CC7) , enUSA

221E157083E157084E168191Steering Wheel

VOICE CONTROL (IF EQUIPPED)

Type 2

See Cruise Control (page 179). INFORMATION DISPLAY CONTROL

End a call Answer a call Voice recognition

See SYNC™ (page 309). See MyFord Touch™ (page 346). CRUISE CONTROL Type 1

See Information Displays (page 87).

65

Fusion (CC7) , enUSA

E168194E144500E144501E144636Steering Wheel

Cluster Display Control Features

If equipped with: MyFord system: This control functions the same as the center control on the faceplate. See Audio unit (page 295). MyFord Touch: Use this control to adjust the right side of the cluster display. Navigate through the screen and press OK to select. See MyFord Touch™ (page 346). HEATED STEERING WHEEL (IF EQUIPPED) See MyFord Touch™ (page 346).

66

Fusion (CC7) , enUSA

E144811Wipers and Washers

WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

Single wipe Intermittent wipe Normal wipe High speed wipe

Intermittent Wipe

Shortest wipe interval Intermittent wipe Longest wipe interval

Use the rotary control to adjust the intermittent wipe interval. Speed Dependent Wipers When your vehicle speed increases, the interval between wipes will decrease. AUTOWIPERS (IF EQUIPPED) Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: If you switch autolamps on in conjunction with autowipers, your low beam headlamps will illuminate automatically when the rain sensor activates the windshield wipers continuously.

67

Fusion (CC7) , enUSA

DCBE169313ACBAE169314Wipers and Washers

Note: Wet or winter driving conditions with ice, snow or salty road mist can cause inconsistent and unexpected wiping or smearing. In these conditions, you can do the following to help keep your windshield clear: •

Lower the sensitivity of the autowipers to reduce the amount of smearing. Switch to normal or high-speed wipe. Switch the autowipers off.

• •

Use the rotary control to adjust the sensitivity of the rain sensor. Set the control to low sensitivity, and the wipers will turn on when the rain sensor detects a large amount of moisture on the windshield. Set the control to high sensitivity, and the wipers will turn on when the rain sensor detects a small amount of moisture on the windshield. Keep the outside of the windshield clean. The rain sensor is very sensitive. If the area around the mirror is dirty, then the wipers may operate if dirt, mist or insects hit the windshield. WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat.

Highest sensitivity On Lowest sensitivity

The autowipers feature uses a rain sensor. You will find it in the area around the interior mirror. The rain sensor monitors the amount of moisture on the windshield and automatically turns on the wipers. It will adjust the wiper speed by the amount of moisture that the sensor detects on the windshield. You can turn this feature on and off in the information display. See General Information (page 87).

To operate the washers and spray the windshield, pull the lever toward you. A wipe will occur a few seconds after washing to clear any remaining washer fluid. This feature can be switched on or off in the information display. See General Information (page 87).

68

Fusion (CC7) , enUSA

ACBE169315E169316Lighting

LIGHTING CONTROL

Headlamp Flasher

Off Parking lamps, instrument panel lamps, license plate lamps and tail lamps Headlamps

High Beams

Pull the lever toward you slightly and release it to flash the headlamps.

AUTOLAMPS (IF EQUIPPED)

Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off.

The headlamps will switch on and off automatically in low light situations or during inclement weather. The headlamps will remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps will remain on. See Information Displays (page 87).

69

Fusion (CC7) , enUSA

E142449E162679E162680E142451Lighting

When the headlamp switch is in the Autolamps position, the windshield wiper activated exterior lamps will turn on within 10 seconds when you switch the windshield wipers on. The exterior lamps will turn off approximately 60 seconds after you switch the windshield wipers off. This feature does not turn on the exterior lamps: • • while the wipers are on to clear washer

during a mist wipe

•

fluid during a wash condition if the wipers are in automatic or intermittent modes.

Note: If you have autolamps and autowipers switched on the low beam headlamps will turn on automatically when the windshield wipers operate continuously. Note: You may have to manually switch the headlamps on in severe weather conditions. Note: If you have autolamps switched on you can only switch the high beam headlamps on once the system has turned the headlamps on. INSTRUMENT LIGHTING DIMMER Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting.

Vehicles With Front Fog Lamps

Press repeatedly or press and hold until you reach the desired level. Vehicles Without Front Fog Lamps

Press repeatedly or press and hold to dim. Press repeatedly or press and hold to brighten.

70

Fusion (CC7) , enUSA

E132712ABE165366Lighting

HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on. DAYTIME RUNNING LAMPS (IF EQUIPPED)

WARNING

Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

The system switches the low beam headlamps on at a reduced intensity in daylight conditions. To switch the system on, switch the ignition on, and switch the lighting control to the off, autolamp or parking lamp position.

AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED) The system will automatically turn on your high beams if it is dark enough and no other traffic is present. When it detects the headlights of an approaching vehicle, the tail lamps of the preceding vehicle or street lighting, the system will turn off the high beams before they distract other drivers. The low beams remain on. Note: If it appears that automatic control of the high beams is not functioning properly, check the windshield in front of the camera for a blockage. A clear view of the road is required for proper system operation. Have any windshield damage in the area of the camera’s field-of-view repaired. Note: If the system detects a blockage such as bird droppings, bug splatter, snow or ice, and you do not observe changes, the system will go into low beam mode until you clear the blockage. A message may also appear in the instrument cluster display noting the front camera is blocked. Note: Typical road dust, dirt and water spots will not affect the performance of the automatic high beam system . However, in cold or inclement weather conditions, you will notice a decrease in the availability of the high beam system, especially at start up. If you want to change the beam state independently of the system, you may switch the high beams on or off using the multifunction switch. Automatic control will resume when conditions are correct. Note: Modification of the vehicle ride height such as using much larger tires, may degrade feature performance. A camera sensor, centrally mounted behind the windshield of your vehicle, continuously monitors conditions to decide when to switch the high beams off and on.

71

Fusion (CC7) , enUSA

Lighting

Once the system is active, the high beams will switch on if: • • •

the ambient light level is low enough there is no traffic in front of the vehicle the vehicle speed is greater than 25 mph (40 km/h)

Manually Overriding the System

•

•

•

The high beams will switch off if: •

the system detects the headlamps of an approaching vehicle or the tail lamps of a preceding vehicle. vehicle speed falls below 16 mph (25 km/h) the ambient light level is high enough that high beams are not required the system detects severe rain, snow or fog the camera is blocked

• Activating the System Switch on the system using the information display and autolamps. See Information Displays (page 87). See Autolamps (page 69).

When the automatic control has activated the high beams, pushing or pulling the stalk will provide a temporary override to low beam. Use the information display menu to permanently deactivate the system, or turn the lighting control switch from autolamps to headlamps. FRONT FOG LAMPS (IF EQUIPPED)

Switch the lighting control to the autolamps position.

Press the control to switch the fog lamps on or off. You can switch the fog lamps on when the lighting control is in any position except Off and the high beams are not on.

72

Fusion (CC7) , enUSA

E142451E169254E142453DIRECTION INDICATORS

Lighting

Note: Press button C to switch the door function off when you open any door. The indicator lamp will light amber when the door function is off. When the door function is off and you open a door, the courtesy and door lamps will stay off. Press button C again to switch the door function back on. The indicator lamp will light blue when the door function is on. When the door function is on and you open a door, the courtesy and door lamps will light.

All lamps on button Door function button All lamps off button Individual dome lamps

You can switch individual map lamps on independently by pressing a map lens. Rear Interior Lamp (If Equipped)

Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. INTERIOR LAMPS The lamps will turn on when you have met one of the following conditions: • • •

You open any door. You press a remote control button. You press button A on the front interior lamp.

Front Interior Lamp Note: The front interior lamp buttons are on the overhead console. The exact location of each button on the overhead console depends upon which roof, sunroof, and window shade features are equipped on the vehicle.

73

Fusion (CC7) , enUSA

E169255E167127ABCDDE169470Lighting

You can switch dome lamps on by pressing the button. AMBIENT LIGHTING (IF EQUIPPED) The ambient lighting system is adjusted with the MyFord Touch. See MyFord Touch™ (page 346).

74

Fusion (CC7) , enUSA

Windows and Mirrors

Bounce-Back The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care

when closing the windows to avoid personal injury or damage to your vehicle.

Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection. The window will stop if you release the switch before the window closes fully. Window Lock

Press the control to lock or unlock the rear window controls. It will illuminate when you lock the rear window controls. Accessory Delay You can use the window switches for several minutes after you switch the ignition off or until you open either front door.

POWER WINDOWS WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. Press the switch to open the window. Lift the switch to close the window. One-Touch Down Press the switch fully and release it. Press again or lift it to stop the window. One-Touch Up Lift the switch fully and release it. Press or lift it again to stop the window.

75

Fusion (CC7) , enUSA

E146043E144072Windows and Mirrors

GLOBAL OPENING AND CLOSING You can use the remote control to operate the windows with the ignition off. Note: You can enable or disable this feature in the information display or see an authorized dealer. See General Information (page 87). Note: To operate this feature, accessory delay must not be active. Opening the Windows You can only open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows and vent the moonroof. Release the button once movement starts. Press the lock or unlock button to stop movement. Closing the Windows WARNING

When closing the windows and moonroof, you should verify they are free of obstructions and make sure

that children and pets are not in the proximity of the window openings.

To close the windows and moonroof, press and hold the remote control lock button. Release the button once movement starts. Press the lock or unlock button to stop movement. EXTERIOR MIRRORS Power Exterior Mirrors WARNING

Do not adjust the mirrors when your vehicle is moving.

76

Fusion (CC7) , enUSA

Left-hand mirror Adjustment control Right-hand mirror

To adjust a mirror: 1. Select the mirror you want to adjust.

The control will illuminate.

2. Adjust the position of the mirror. 3. Press the mirror switch again. Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 119). Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Memory Function (page 124). Auto-Dimming Feature (If Equipped) The driver exterior mirror automatically dims when the interior auto-dimming mirror turns on.

E144073Windows and Mirrors

Signal Indicator Mirrors (If Equipped) The outer portion of the appropriate mirror housing will blink when you switch on the turn signal. Integrated Blind Spot Mirrors (If Equipped)

WARNING

Objects in the blind spot mirror are closer than they appear.

Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They can increase your visibility along the side of your vehicle. Check the main mirror first before a lane change, then check the blind spot mirror. If the blind spot mirror does not show any vehicles in its viewing area and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.

Fusion (CC7) , enUSA

The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C). Blind Spot Monitor (If Equipped) See Blind Spot Information System (page 191). INTERIOR MIRROR WARNING

Do not adjust the mirror when your vehicle is moving.

77

ABCE138665Windows and Mirrors

Illuminated Vanity Mirror

Lift the cover to switch the lamp on. MOONROOF (IF EQUIPPED)

WARNINGS

Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously

hurt themselves.

When closing the moonroof, you should verify that it is free of obstructions and make sure that

children and pets are not in the proximity of the roof opening.

The sliding shade can be manually opened or closed when the moonroof is closed. Pull the shade toward the front of the vehicle to close it. The moonroof controls are located on the overhead console and have a one-touch open and close feature. To stop it during one-touch operation, touch the control a second time.

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up. SUN VISORS

Rotate the sun visor toward the side window and extend it rearward for extra shade.

78

Fusion (CC7) , enUSA

E138666E162197Windows and Mirrors

Open Vent Close

Opening and Closing the Moonroof Touch (A) to open the moonroof. It will stop short of the fully opened position. Note: This position helps to reduce wind noise or rumbling which may happen with the moonroof fully open. Touch (A) again to fully open the moonroof. Touch (C) to close the moonroof. Bounce-Back The moonroof will stop automatically and reverse some distance if an obstacle is detected while closing. Touch and hold (C) within two seconds of a bounce-back event to override this function. Venting the Moonroof Touch (B) to vent the moonroof. Touch (C) to close it.

79

Fusion (CC7) , enUSA

E144499Instrument Cluster

GAUGES Type 1 and 2

Tachometer Information Display (Type 2 shown Type 1 similar) Speedometer