2014 Ford Fusion Owners Manual

highly specialized tools developed specifically for servicing your vehicle. To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. See Scheduled Maintenance (page 428). If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your warranty information to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft® parts are designed and built to provide the best performance in your vehicle. Precautions • Do not work on a hot engine. • Make sure that nothing gets caught in

moving parts.

• Do not work on a vehicle with the

engine running in an enclosed space, unless you are sure you have enough ventilation. Keep all open flames and other burning material (such as cigarettes) away from the battery and all fuel related parts.

•

Working with the Engine Off 1. Set the parking brake and shift to P

(Park).

2. Turn off the engine and remove the key

(if equipped).

3. Block the wheels. Working with the Engine On

WARNING

To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

1. Set the parking brake and shift to P

(Park).

2. Block the wheels OPENING AND CLOSING THE HOOD

1. To open the hood, go inside the vehicle

and pull the hood release handle located under the left-hand side of the instrument panel.

236

Fusion (CC7) , enUSA

E142457Maintenance

4. Raise the hood and support it with the prop rod by securing the prop rod in the proper hole in the hood.

5. To close the hood, lift the hood slightly

and separate the prop rod from the hood and secure the prop rod in the clip.

6. Lower the hood and allow it to drop the

last 10-12 inches (25 to 30
centimeters).

Note: Make sure that you close the hood properly and that it fully latches on both sides of the hood.

2. Go to the front of the vehicle and locate the secondary release lever, which is located under the front of the hood, to your right of the center of the vehicle (driver's side), near the headlight.

3. Release the hood latch by pushing the yellow secondary release lever to your left, toward the center of the vehicle.

237

Fusion (CC7) , enUSA

E169261Maintenance

UNDER HOOD OVERVIEW - 1.5L ECOBOOST™/1.6L ECOBOOST™

Engine coolant reservoir Engine oil filler cap Engine oil dipstick Brake fluid reservoir cap Battery Power distribution box Engine air filter assembly Windshield washer fluid reservoir cap

238

Fusion (CC7) , enUSA

E167624ABCDEFHGMaintenance

UNDER HOOD OVERVIEW - 2.0L ECOBOOST™

Engine coolant reservoir cap Engine oil dipstick Engine oil filler cap Brake fluid reservoir cap Battery Power distribution box Engine air filter assembly Windshield washer fluid reservoir cap

239

Fusion (CC7) , enUSA

E159754Maintenance

UNDER HOOD OVERVIEW - 2.5L

A. Engine coolant reservoir cap B. Engine oil filler cap C. Engine oil dipstick D. Brake fluid reservoir cap E. Battery F. Power distribution box G. Air filter housing cover H. Windshield washer fluid reservoir cap

240

Fusion (CC7) , enUSA

E169801Maintenance

Note: Make sure that the level is between the MIN and the MAX marks. 1. Make sure that your vehicle is on level

ground.

2. Turn the engine off and wait 10 minutes

for the oil to drain into the oil pan.

3. Remove the dipstick and wipe it with

a clean, lint-free cloth. Replace the dipstick and remove it again to check the oil level.

If the level is at the MIN mark, add oil immediately. Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage.

Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers.

ENGINE OIL DIPSTICK - 1.5L ECOBOOST™/1.6L ECOBOOST™

MIN MAX

ENGINE OIL DIPSTICK - 2.0L ECOBOOST™/2.5L

MIN MAX

ENGINE OIL CHECK Note: Check the level before starting the engine.

241

Fusion (CC7) , enUSA

E146020ABE169062E142732Maintenance

1. Remove the filler cap. 2. Add engine oil that meets the Ford specifications. See Capacities and Specifications (page 287).

3. Replace the filler cap. Turn it until you

feel a strong resistance.

OIL CHANGE INDICATOR RESET To reset the oil monitoring system after an oil change, See General Information (page 87). ENGINE COOLANT CHECK Checking the Engine Coolant When the engine is cold, check the concentration and level of the engine coolant at the intervals listed in the scheduled maintenance information. See Scheduled Maintenance (page 428). Note: Make sure that the level is between the MIN and MAX marks on the coolant reservoir. Note: Coolant expands when it is hot. The level may extend beyond the MAX mark Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately. See Adding Engine Coolant in this chapter. The coolant concentration should be maintained within 48% to 50%, which equates to a freeze point between -29°F (-34°C) and -35°F (-37°C). Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from an authorized dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations.

Note: Automotive fluids are not interchangeable. Do not use engine coolant or antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding Engine Coolant WARNINGS

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.

Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine

coolant could make it difficult to see through the windshield.

To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.

Do not add coolant further than the MAX mark.

Note: Do not use stop leak pellets, cooling system sealants, or additives as they can cause damage to the engine cooling or heating systems. This damage would not be covered under your vehicle’s warranty. Note: During normal vehicle operation, the engine coolant may change color from orange to pink or light red. As long as the engine coolant is clear and uncontaminated, this color change does not indicate the engine coolant has degraded nor does it require the engine coolant to be drained, the system to be flushed, or the engine coolant to be replaced.

242

Fusion (CC7) , enUSA

Maintenance

•

• Do not mix different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty. Use prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 287). In case of emergency, a large amount of water without engine coolant may be added in order to reach a vehicle service location. In this instance, the cooling system must be drained, chemically cleaned with Motorcraft® Premium Cooling System Flush, and refilled with engine coolant as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing. • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant.

Unscrew the cap slowly. Any pressure will escape as you unscrew the cap. Add prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 287). Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough prediluted engine coolant to bring the coolant level to the proper level.

Recycled Engine Coolant Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Severe Climates If you drive in extremely cold climates: It may be necessary to have a Ford • authorized dealer increase the coolant concentration above 50%.

• A coolant concentration of 60% will

provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.

If you drive in extremely hot climates: It may be necessary to have a Ford • authorized dealer decrease the coolant concentration to 40%.

• A coolant concentration of 40% will

provide improved overheat protection. Engine coolant concentrations below 40% will decrease the corrosion/freeze protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.

243

Fusion (CC7) , enUSA

Maintenance

When Fail-Safe Mode Is Activated

WARNINGS

Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist, and power brake assist, which may increase the possibility of a crash resulting in serious injury.

Never remove the coolant reservoir cap while the engine is running or hot.

You have limited engine power when in the fail-safe mode, so drive your vehicle with caution. Your vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine.

2. Arrange for the vehicle to be taken to

3.

an authorized dealer. If this is not possible, wait a short period for the engine to cool.

4. Check the coolant level and replenish

if low.

5. Re-start the engine and take your

vehicle to an authorized dealer.

Note: Driving your vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible.

What You Should Know About Fail- Safe Cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The fail-safe distance depends on outside temperatures, vehicle load and terrain. How Fail-Safe Cooling Works If the engine begins to overheat, the engine coolant temperature gauge will move to the red (hot) area and:

A high engine temperature message will appear in the information display. The service engine soon indicator will light. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs, your vehicle will still operate. However: • •

The engine power will be limited. The air conditioning system will be disabled.

Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage.

244

Fusion (CC7) , enUSA

Maintenance

WASHER FLUID CHECK

WARNING

If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze

protection. Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See Capacities and Specifications (page 287). State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system. FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. CHANGING THE 12V BATTERY

WARNINGS

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow

flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

AUTOMATIC TRANSMISSION FLUID CHECK Note: Transmission fluid should be checked by an authorized dealer. If required, fluid should be added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. Have an authorized dealer check and change the transmission fluid and filter at the correct service interval. See Scheduled Maintenance (page 428). Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e., if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. BRAKE AND CLUTCH FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately. POWER STEERING FLUID CHECK Your vehicle is equipped with an electric power steering (EPS) system. There is no fluid reservoir to check or fill.

245

Fusion (CC7) , enUSA

Maintenance

Note: If a person adds electrical or electronic accessories or components to the vehicle, the accessories or components may adversely affect the low voltage battery performance and durability and may also affect the performance of other electrical systems in the vehicle. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. When a battery replacement is required, the battery should only be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle. Because your vehicle’s engine is electronically-controlled by a computer, some engine control settings are maintained by power from the low voltage battery. Some engine computer settings, like the idle trim and fuel trim strategy, optimize the driveability and performance of the engine. Some other computer settings, like the clock and radio station presets, are also maintained in memory by power from the low voltage battery. When a technician disconnects and connects the low voltage battery, these settings are erased. Complete the following procedure in order to restore the settings: 1. With the vehicle at a complete stop,

set the parking brake.

2. Shift the transmission into P. 3. Turn off all accessories. 4. Step on the brake pedal and start the

vehicle.

WARNINGS

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or

clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

Your vehicle is equipped with a Motorcraft® maintenance-free battery which normally does not require additional water during its life of service. Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. Note: See an authorized dealer for low voltage battery access, testing, or replacement. When a low voltage battery replacement is necessary, see an authorized dealer to replace the low voltage battery with a Ford recommended replacement low voltage battery that matches the electrical requirements of the vehicle To ensure proper operation of the battery management system (BMS), do not allow a technician to connect any electrical device ground connection directly to the low voltage battery negative post. A connection at the low voltage battery negative post can cause inaccurate measurements of the battery condition and potential incorrect system operation.

246

Fusion (CC7) , enUSA

Maintenance

5. Run the engine until it reaches normal

operating temperature. While the engine is warming up, complete the following: Reset the clock. See Audio System (page 294). Reset the power windows bounce-back feature. See Windows and Mirrors (page 75). Reset the radio station presets. See Audio System (page 294).

6. Allow the engine to idle for at least one minute. If the engine turns off, step on the accelerator to start the engine.

7. While the engine is running, step on the brake pedal and shift the transmission to N.

8. Allow the engine to run for at least one minute by pressing on the accelerator pedal.

9. Drive the vehicle at least 10 miles (16
kilometers) to completely relearn the idle and fuel trim strategy.

Note: If you do not allow the engine to relearn the idle and fuel trim strategy, the idle quality of your vehicle may be adversely affected until the engine computer eventually relearns the idle trim and fuel trim strategy. Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. Note: It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.

Fusion (CC7) , enUSA

CHECKING THE WIPER BLADES

Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES The wiper arms can be manually moved when the ignition is off. This allows for ease of blade replacement and cleaning under the blades.

1. Pull the wiper blade and arm away

from the glass.

2. Press the locking buttons together. 3. Rotate and remove the wiper blade. 4.

Install in the reverse order.

247

E142463E129990112Maintenance

Note: Make sure that the wiper blade locks into place. Lower the wiper arm and blade back to the windshield. The wiper arms will automatically return to their normal position when the ignition is turned on. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. ADJUSTING THE HEADLAMPS Vertical Aim Adjustment The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer. Headlamp Aiming Target

Vertical Aim Adjustment Procedure 1. Park the vehicle directly in front of a

wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

2. Measure the height of the headlamp

bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height.

Note: To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 3. Turn on the low beam headlamps to

illuminate the wall or screen and open the hood.

4. On the wall or screen you will observe

a flat zone of high intensity light located at the top of the right hand portion of the beam pattern. If the top edge of the high intensity light zone is not at the horizontal reference line, the headlamp will need to be adjusted.

8 feet (2.4 meters) Center height of lamp to ground 25 feet (7.6 meters) Horizontal reference line

248

Fusion (CC7) , enUSA

E142592E142465Maintenance

5. Locate the vertical adjuster on each

headlamp. Using a Phillips #2
screwdriver, turn the adjuster either clockwise or counterclockwise in order to adjust the vertical aim of the headlamp. The horizontal edge of the brighter light should touch the horizontal reference line.

6. Close the hood and turn off the lamps. Horizontal Aim Adjustment Horizontal aim is not required for this vehicle and is not adjustable.

REMOVING A HEADLAMP

1. Make sure the headlamp control is in the off position and open the hood.

2. Remove the six fasteners securing the

front fascia to the front trim cover.

3. Remove the three bumper cover upper

screws.

4. Remove the fastener at the inboard

side of the headlamp you are servicing.

249

Fusion (CC7) , enUSA

E145594E159693Maintenance

5. Remove the two headlamp assembly

screws.

8. Separate the front bumper cover from the fender and pull the fender outward 1.2 inches (3 centimeters).

6. Remove the lower three wheel housing

fasteners.

9. From the front of the vehicle, pull the front bumper cover forward 4 inches (10 centimeters).

7. Remove the three front bumper cover lower fasteners, only on the side of the headlamp you are servicing.

10. Carefully pull the headlamp assembly

outward to disengage it from the lower fixing point.

250

Fusion (CC7) , enUSA

E159694E159695E159696E159697E159698E159699Maintenance

Replacing the Headlamp Bulbs

WARNING

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb by only its

plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

Headlamp assembly: A. Side marker lamp bulb B. High beam headlamp bulb C. Low beam headlamp bulb D. Front parking/Turn signal lamp bulb Replacing the High Beam Headlamp Bulb 1. Remove the headlamp assembly. 2. Remove the service cap. 3. Disconnect the electrical connector. 4. Turn the bulb counterclockwise and

remove it from the headlamp assembly. Install the new bulb in reverse order.

11.

Carefully lift the headlamp and remove it from the vehicle.

12. Disconnect the electrical connector. CHANGING A BULB Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. Examples of acceptable condensation are: • Presence of thin mist (no streaks, drip

marks or droplets). Fine mist covers less than 50% of the lens.

•

Examples of unacceptable moisture (usually caused by a lamp water leak) are: • Water puddle inside the lamp. •

Large water droplets, drip marks or streaks present on the interior of the lens.

Take your vehicle to an authorized dealer for service if any of the above conditions of unacceptable moisture are present.

5.

251

Fusion (CC7) , enUSA

ABCDE159753Maintenance

3. Remove the push pins and reposition

the inner body side trim.

4. Remove the three lamp assembly nuts. 5. Gently pull the lamp assembly away

from the vehicle.

Replacing the Low Beam Headlamp Bulb 1. Remove the headlamp assembly. 2. Remove the service cap. 3. Disconnect the electrical connector. 4. Release the retainer spring and remove

it from the headlamp assembly. Install the new bulb in reverse order.

5. Replacing the Front Parking/Turn Signal Lamp Bulb 1. Remove the headlamp assembly. 2. Turn the bulb assembly

counterclockwise and remove it from the headlamp assembly.

3. Separate the bulb from the bulb

socket. 4. Install the new bulb in reverse order. Replacing the Side Marker Lamp Bulb 1. Remove the headlamp assembly. 2. Remove the service cap. 3. Depress the tabs on the socket and

remove the socket and bulb together.

4. Separate the bulb from the bulb

socket. 5. Install the new bulb in reverse order. Replacing the Tail, Brake, High- Mount Brake Lamp, and Turn Signal Lamp Bulbs These lamps are designed with LED light sources. For replacement, see your authorized dealer. Replacing a Reverse Lamp Bulb 1. Make sure the lighting control is in the

off position.

2. Open the trunk deck lid.

252

Fusion (CC7) , enUSA

E145777E145778Maintenance

7. Remove the bulb from the bulb holder. Install the new bulb in reverse order. Replacing the License Plate Lamp Bulb

6. Turn the bulb holder counterclockwise

and remove the bulb holder.

1. Carefully release the spring clip. 2. Remove the lamp. 3. Remove the bulb. Install the new bulb in reverse order. BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to make sure they have the proper lamp performance, light brightness, light pattern, and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb illumination time.

Function

*Headlamp high beam (Halogen) *Headlamp low beam (Halogen) *Side marker lamp - front

Trade name

H7LL H11LL LED

253

Fusion (CC7) , enUSA

E145779E145780321E72789Maintenance

Function

Trade name

W5W

PWY24W

*Park lamp - front *Turn lamp - front *Fog lamp - front *Tail and brake lamp - high series *Tail and brake lamp - low series Reverse lamp *Turn lamp - rear - high series *Turn lamp - rear - low series *Side marker lamp - rear License plate lamp *Trunk lamp *High-mount brake lamp *Side repeater lamp *Interior lamp *To replace these bulbs, see your authorized dealer. To replace all instrument panel bulbs, see your authorized dealer. **If so equipped.

H11
LED LED 921
LED LED LED W5W

LED LED LED

W5W or LED**

254

Fusion (CC7) , enUSA

Maintenance

CHANGING THE ENGINE AIR FILTER

2.5L Engine

1. Release the clamps that secure the air

filter housing cover.

2. Carefully lift the air filter housing cover. 3. Remove the air filter element from the

air filter housing.

5.

4. Wipe any dirt or debris from the air filter housing and cover to make sure no dirt gets in the engine and to make sure you have a good seal. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. Install the air filter housing cover.

6. 7. Engage the clamps to secure the air

filter housing cover to the air filter housing.

WARNING

To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

When changing the air filter element, use only the air filter element listed. See Capacities and Specifications (page 287). For EcoBoost equipped vehicles: When servicing the air cleaner, it is important that no foreign material enter the air induction system. The engine and turbocharger are susceptible to damage from even small particles. Change the air filter element at the proper interval. See Scheduled Maintenance (page 428). Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used. EcoBoost Engines

255

Fusion (CC7) , enUSA

E144365E146047Vehicle Care

CLEANING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash. • Never use strong household detergents

or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces.

• Never wash a vehicle that is “hot to the

touch” or during exposure to strong, direct sunlight.

•

• Dry your vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting. Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to your vehicle’s paintwork and trim over time. Use Motorcraft Bug and Tar Remover.

• Remove any exterior accessories, such

as antennas, before entering a car wash.

Note: Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible. Stripes or Graphics (if equipped) Do not use a commercial or high-pressure sprayer on the surface or edge of stripes and graphics. This can cause damage to the film and cause the edge of the film to peel away from the vehicle surface. Exterior Chrome Note: Never use abrasive materials such as steel wool or plastic pads as they can scratch the chrome surface. Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers

GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Detail Wash (ZC-3-A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Quality Windshield Washer Fluid (Canada only) [CXC-37-(A, B, D or F)] Motorcraft Premium Windshield Wash Concentrate with Bitterant (U.S. only) (ZC-32-B1) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Wheel and Tire Cleaner (ZC-37-A)

256

Fusion (CC7) , enUSA

Vehicle Care

• Use a quality wax that does not contain

abrasives. Follow the manufacturer’s instructions to apply and remove the wax.

•

• Apply a small amount of wax in a

back-and-forth motion, not in circles. • Do not allow wax to come in contact with any non-body (low-gloss black) colored trim. The wax will discolor or stain the parts over time. • Roof racks. • Bumpers. • Grained door handles. • Side moldings. • Mirror housings. • Windshield cowl area.

• Do not apply wax to glass areas. • After waxing, your car's paint should

feel smooth, and be free of streaks and smudges.

CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: •

Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.

•

• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. Spray Motorcraft Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo.

• Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage.

• Wash your vehicle first, using cool or

lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash.

• Use Motorcraft Custom Bright Metal

Cleaner. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.

• Do not apply cleaning product to hot

surfaces and do not leave cleaning product on chrome surfaces longer than the time recommended.

• Using other non-recommended cleaners can result in severe and permanent cosmetic damage.

Underbody Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. Cleaning Plastic Exterior Parts Use only approved products to clean plastic parts •

For routine cleaning, use Motorcraft Detail Wash. If tar or grease spots are present, use Motorcraft Bug and Tar Remover.

•

WAXING Regular waxing is necessary to protect your car's paint from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Always wash your vehicle before applying wax.

257

Fusion (CC7) , enUSA

Vehicle Care

• Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations.

• Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine.

•

CLEANING THE WINDOWS AND WIPER BLADES Car wash chemicals and environmental fallout can result in windshield and wiper blade contamination. Dirty windshield and wipers will result in poor windshield wiper operation. Keep the windshield and wiper blades clean to maintain windshield wiper performance. To clean the windshield and wiper blades: • Clean the windshield with a non-abrasive glass cleaner. For windshields contaminated with tree sap, chemicals, wax or bugs, clean the entire windshield using steel wool (no greater than 0000 grade) in a circular motion and rinse with water. • Clean the wiper blades with isopropyl rubbing alcohol or windshield washer fluid.

Note: Do not use razor blades or other sharp objects to clean or remove decals from the inside of the heated rear window. The vehicle warranty does not cover damage caused to the heated rear window grid lines. CLEANING THE INTERIOR

WARNINGS

Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the

belt webbing.

WARNINGS

On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.

For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a

vacuum cleaner.

•

• Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner. If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover. In Canada, use Motorcraft Multi-Purpose Cleaner. If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set.

•

• Do not use household cleaning

products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.

CLEANING THE INSTRUMENT PANEL AND INSTRUMENT CLUSTER LENS

WARNING

Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel

to avoid contamination of the airbag system.

258

Fusion (CC7) , enUSA

Vehicle Care

Clean the instrument panel and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • Avoid cleaners or polishes that increase

the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect you from undesirable windshield reflection. Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces.

•

• Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.

• Do not allow air fresheners and hand sanitizers to spill onto interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty.

If a staining liquid like coffee or juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean,

white, cotton cloth.

2. Wipe the surface with a damp, clean, white cotton cloth. For more thorough cleaning, use a mild soap and water solution. If the spot cannot be completely cleaned by this method, the area may be cleaned using a commercially available cleaning product designed for automotive interiors. If necessary, apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area. Allow this to set at room temperature for 30
minutes.

3.

Fusion (CC7) , enUSA

4. Remove the soaked cloth and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60
seconds.

5. Following this, wipe area dry with a

clean, white, cotton cloth.

CLEANING LEATHER SEATS (IF EQUIPPED)

For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. Dry the area with a soft cloth. If you cannot completely clean the leather using a mild soap and water solution, you can try a commercially available leather cleaning product designed for automotive interiors. Note: To check for compatibility, first test any cleaner or stain remover on an inconspicuous part of the leather. You should: •

remove dust and loose dirt with a vacuum cleaner clean spills and stains as quickly as possible check for compatibility by first testing any cleaner or stain remover on an inconspicuous part of the leather.

•

•

Do not use the following products as these may damage the leather: •

oil/petroleum-based leather conditioners household cleaners alcohol solutions solvents or cleaners intended specifically for rubber, vinyl and plastics.

• • •

259

Vehicle Care

REPAIRING MINOR PAINT DAMAGE Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird

droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.

• Always read the instructions before

using the products.

CLEANING THE ALLOY WHEELS Note: Do not apply a cleaning chemical to warm or hot wheel rims and covers. Note: Some automatic car washes may cause damage to the finish on your wheel rims and covers. Note: Industrial-strength or heavy-duty cleaners in combination with brush agitation to remove brake dust and dirt, could wear away the clear coat finish over a period time. Note: Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergents. Note: If you intend parking your vehicle for an extended period after cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so. This will reduce the risk of increased corrosion of the brake discs. Alloy wheels and wheel covers are coated with a clear coat paint finish. To maintain their condition we recommend that you:

• Clean the wheels weekly using

Motorcraft Wheel and Tire Cleaner. Apply using manufacturer's instructions.

• Use a sponge to remove heavy deposits of dirt and brake dust accumulation.

• Rinse thoroughly with a strong stream of water when you have completed the cleaning process. To remove tar and grease, use Motorcraft Bug and Tar Remover.

•

VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), read the following maintenance recommendations to make sure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested for reliable, regular driving. Long term storage under various conditions may lead to component degradation or failure unless specific precautions are taken to preserve the components. General •

Store all vehicles in a dry, ventilated place.

• Protect from sunlight, if possible. If vehicles are stored outside, they • require regular maintenance to protect against rust and damage.

Body • Wash your vehicle thoroughly to

remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and underside of front fenders.

• Periodically wash your vehicle stored

in exposed locations.

260

Fusion (CC7) , enUSA

Vehicle Care

•

Battery • Check and recharge as necessary. Keep

connections clean. If storing your vehicle for more than 30
days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting.

Note: If battery cables are disconnected, it will be necessary to reset memory features. Brakes • Make sure brakes and parking brake

are fully released.

Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers

and pins under your vehicle are covered with grease to prevent rust.

• Move vehicles at least 25 feet (8
meters) every 15 days to lubricate working parts and prevent corrosion. Removing Vehicle From Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt

or grease film build-up on window surfaces.

• Check windshield wipers for any

deterioration.

• Check under the hood for any foreign

material that may have collected during storage (mice/squirrel nests).

• Check the exhaust for any foreign material that may have collected during storage.

• Check tire pressures and set tire

inflation per the Tire Label.

•

Touch-up exposed or primed metal to prevent rust.

• Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when your vehicle is washed. Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil.

•

• Cover interior trim to prevent fading. •

Keep all rubber parts free from oil and solvents.

Engine •

The engine oil and filter should be changed prior to storage, as used engine oil contain contaminates that may cause engine damage. Start the engine every 15 days. Run at fast idle until it reaches normal operating temperature

•

• With your foot on the brake, shift

through all the gears while the engine is running. Fuel system •

Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle.

Cooling system • Protect against freezing temperatures. • When removing your vehicle from storage, check coolant fluid level. Confirm there are no cooling system leaks, and fluid is at the recommended level.

261

Fusion (CC7) , enUSA

Vehicle Care

• Check brake pedal operation. Drive

your vehicle 15 feet (4.5 meters) back and forth to remove rust build-up.

• Check fluid levels (including coolant, oil and gas) to make sure there are no leaks, and fluids are at recommended levels. If the battery was removed, clean the battery cable ends and inspect.

•

Contact your authorized dealer if you have any concerns or issues.

262

Fusion (CC7) , enUSA

Wheels and Tires

TIRE CARE Important information for 235/40R19 low-profile tires and wheels If your vehicle is equipped with 235/40R19 tires, they are low-profile tires. These tires and wheels are designed to give your vehicle a sport appearance. With low-profile tires, you may notice an increase in road noise and faster tire wear, depending on road conditions and driving styles. Due to their design, low-profile tires and wheels are more prone to road damage from potholes, rough or unpaved roads, car wash rails and curb contact than standard tires and wheels. Note: Your vehicle’s warranty does not cover these types of damage. Tires should always be kept at the correct inflation pressures and extra caution should be taken when operating on rough roads to avoid impacts that could cause wheel and tire damage. Information About Uniform Tire Quality Grading

Tire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200
Traction AA Temperature A. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, light truck or LT type tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104 (c)(2). U.S. Department of Transportation Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150
would wear 1 ½ times as well on

263

Fusion (CC7) , enUSA

E142542Wheels and Tires

the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction AA A B C

WARNING

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.

The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

Temperature A B C

WARNING

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Glossary of Tire Terminology * Tire label: A label showing the original equipment tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry.

264

Fusion (CC7) , enUSA

Wheels and Tires

*Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. *Inflation pressure: A measure of the amount of air in a tire. *Standard load: A class of P-metric or Metric tires designed to carry a maximum load at set pressure. For example: For P-metric tires 35 psi (2.4 bar) or 36 (2.5 bar) depending on tire size and for Metric tires 36 psi (2.5
bar). Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. *Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 42 psi (2.9 bar). Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. *kPa: Kilopascal, a metric unit of air pressure. *PSI: Pounds per square inch, a standard unit of air pressure. *Cold tire pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 kilometers).

*Recommended inflation pressure: The cold inflation pressure found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-Pillar or the edge of the driver’s door. *B-pillar: The structural member at the side of the vehicle behind the front door * Bead area of the tire: Area of the tire next to the rim. * Sidewall of the tire: Area between the bead area and the tread. * Tread area of the tire: Area of the perimeter of the tire that contacts the road when mounted on the vehicle. *Rim: The metal support (wheel) for a tire or a tire and tube assembly upon which the tire beads are seated. Information Contained on the Tire Sidewall Both United States and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and

265

Fusion (CC7) , enUSA

Wheels and Tires

A. P: Indicates a tire, designated by the Tire and Rim Association, that may be used for service on cars, sport utility vehicles, minivans and light trucks. Note: If your tire size does not begin with a letter this may mean it is designated by either the European Tire and Rim Technical Organization or the Japan Tire Manufacturing Association. B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 65: Indicates the aspect ratio which gives the tire's ratio of height to width. D. R: Indicates a radial type tire. E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. F. 95: Indicates the tire's load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s manual. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law.

describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. Information on P Type Tires

P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.)

266

Fusion (CC7) , enUSA

HIJKLMABCDEFGE142543Wheels and Tires

G. H: Indicates the tire's speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130
km/h) to 186 mph (299 km/h). These ratings are listed in the following chart. Note: You may not find this information on all tires because it is not required by federal law. mph ( km/h)

Letter rating

81 mph (130 km/h) 87 mph (140 km/h) 99 mph (159 km/h) 106 mph (171 km/h) 112 mph (180 km/h) 118 mph (190 km/h) 124 mph (200 km/h) 130 mph (210 km/h) 149 mph (240 km/h)

Letter rating

mph ( km/h)

168 mph (270 km/h) 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299
km/h), tire manufacturers always use the letters ZR. H. U.S. DOT Tire Identification Number (TIN): This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000
the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season.

267

Fusion (CC7) , enUSA

Wheels and Tires

J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), for the correct tire pressure for your vehicle. L. Treadwear, Traction and Temperature Grades: *Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.

*Traction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. *Temperature: The temperature grades are A (the highest), B and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. M. Maximum Inflation Pressure: Indicates the tire manufacturers' maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the vehicle manufacturer's recommended cold inflation pressure which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label.

268

Fusion (CC7) , enUSA

Wheels and Tires

The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc. Additional Information Contained on the Tire Sidewall for LT Type Tires Note: Tire Quality Grades do not apply to this type of tire.

C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual; defined as four tires on the rear axle (a total of six or more tires on the vehicle). D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single; defined as two tires (total) on the rear axle. Information on T Type Tires T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire.

LT type tires have some additional information beyond those of P type tires; these differences are described below. A. LT: Indicates a tire, designated by the Tire and Rim Association, that is intended for service on light trucks. B. Load Range and Load Inflation Limits: Indicates the tire's load-carrying capabilities and its inflation limits.

269

Fusion (CC7) , enUSA

ABCBDE142544Wheels and Tires

C. 80: Indicates the aspect ratio which gives the tire's ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D.D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. Location of the Tire Label You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver’s door. Inflating Your Tires Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company.

T type tires have some additional information beyond those of P type tires; these differences are described below: A. T: Indicates a type of tire, designated by the Tire and Rim Association, that is intended for temporary service on cars, sport utility vehicles, minivans and light trucks. B. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire.

270

Fusion (CC7) , enUSA

ABCDEE142545Wheels and Tires

(affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles