2013 Ford Fusion Owners Manual

Off Parking lamps, instrument panel lamps, license plate lamps and tail lamps Headlamps

High Beams

Pull the lever toward you slightly and release it to flash the headlamps.

AUTOLAMPS (IF EQUIPPED) Note: It may be necessary to switch your headlamps on manually in severe weather conditions.

Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off.

The headlamps will switch on and off automatically in low light situations or during inclement weather. The headlamps will remain on for a period of time after you switch the ignition off. You can adjust the time delay using the information display controls. See Information Displays (page 83).

67

Fusion/Mondeo (CC7)

E142449E162679E162680E142451Lighting

Note: If you switch autolamps on in conjunction with autowipers, low beam headlamps will illuminate automatically when the rain sensor activates the windshield wipers continuously. INSTRUMENT LIGHTING DIMMER Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting. Vehicles With Front Fog Lamps

Press repeatedly or press and hold until the desired level is reached.

Vehicles Without Front Fog Lamps

Press repeatedly or press and hold to dim. Press repeatedly or press and hold to brighten.

HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on. DAYTIME RUNNING LAMPS (IF EQUIPPED)

WARNING

Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

68

Fusion/Mondeo (CC7)

E132712ABAE142452Lighting

Note: Modification of the vehicle ride height (e.g. using much larger tires) may degrade feature performance. A camera sensor is centrally mounted behind the windshield of the vehicle, and monitors conditions continuously to decide when to switch the high beams off and on. Once the system is active, the high beams will switch on if: •

The ambient light level is low enough that high beams are needed. There is no traffic in front of the vehicle. The vehicle speed is greater than 25 mph (40 km/h).

• •

The high beams will switch off if: • An approaching vehicle's headlights or

a preceding vehicle's tail lamps are detected.

•

• Vehicle speed falls below 16 mph

(25 km/h). The ambient light level is high enough that high beams are not required. Severe rain, snow, or fog is detected. • • The camera is blocked. Activating the System Switch on the system using the information display and autolamps. See Information Displays (page 83). See Autolamps (page 67).

The system switches the low beam headlamps on at a reduced intensity in daylight conditions. To switch the system on, switch the ignition on, and switch the lighting control to the off, autolamp or parking lamp position. AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED) The system will automatically turn on your high beams if it is dark enough and no other traffic is present. When it detects an approaching vehicle’s headlights, a preceding vehicle’s tail lamps or street lighting, the system will turn off the high beams before they distract other drivers. The low beams remain on. Note: If it appears that automatic control of the high beams is not functioning properly, check the windshield in front of the camera for blockage. A clear view of the road is required for proper system operation. Any windshield damage in the area of the camera field-of-view should be repaired. Note: If a blockage is detected (e.g. bird dropping, bug splatter, snow, or ice) and no changes are observed, the system will go into low beam mode until the blockage is cleared. A message may also appear in the instrument cluster display noting the front camera is blocked. Note: Typical road dust, dirt and water spots will not affect the automatic high beam system’s performance. However, in cold or inclement weather conditions, the automatic high beam system's availability may be decreased, especially at startup. If you want to change the beam state independently of the system, you may turn the high beams ON or OFF using the multifunction switch lever. Automatic control will resume when conditions are correct.

69

Fusion/Mondeo (CC7)

E142451Lighting

Turn the lighting control to the autolamps position. Manually Overriding the System

DIRECTION INDICATORS

Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. INTERIOR LAMPS The lamps will switch on when one of the following conditions have been met: • • •

You open any door. You press a remote control button. You touch switch A on the front interior lamp.

Front Interior Lamp Note: The front interior lamp switches are on the overhead console. The exact location of each switch on the overhead console depends upon which roof, sunroof, and window shade features are equipped on the vehicle.

When the automatic control has activated the high beams, pushing or pulling the stalk will provide a temporary override to low beam. To permanently deactivate the system, use the information display menu or turn the lighting control switch from autolamps to headlamps. FRONT FOG LAMPS (IF EQUIPPED)

Press the control to switch the fog lamps on or off. You can switch the fog lamps on when the lighting control is in any position except off and the high beams are not on.

70

Fusion/Mondeo (CC7)

E130140E142453E145595Lighting

You can switch individual dome lamps on independently by pressing switch A.

Note: Touch switch C to switch the door function off when you open any door. The indicator lamp will illuminate amber when the door function is off. When the door function is off and you open a door, the courtesy and door lamps will stay off. Touch switch C again to switch the door function back on. The indicator lamp will illuminate blue when the door function is on. When the door function is on and you open a door, the courtesy and door lamps will switch on.

All lamps on switch All lamps off switch Door function switch

You can switch individual map lamps on independently by touching a map lens. Rear Interior Lamp (If Equipped)

71

Fusion/Mondeo (CC7)

ABCE146410AE142455Windows and Mirrors

Bounce-Back The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care

when closing the windows to avoid personal injury.

Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection. The window will stop if you release the switch before the window is fully closed. Window Lock

Press the control to lock or unlock the rear window controls. It will illuminate when you lock the rear window controls. Accessory Delay You can use the window switches for several minutes after you switch the ignition off or until you open either front door.

POWER WINDOWS WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Note: You may hear a rumbling noise when just one of the windows are open. Lower the opposite window slightly to reduce this noise. Press the switch to open the window. Lift the switch to close the window. One-Touch Down Press the switch fully and release it. Press again or lift it to stop the window. One-Touch Up Lift the switch fully and release it. Press or lift it again to stop the window.

72

Fusion/Mondeo (CC7)

E146043E144072Windows and Mirrors

GLOBAL OPENING AND CLOSING You can use the remote control to operate the windows with the ignition off. Note: You can enable or disable this feature in the information display or see an authorized dealer. See General Information (page 83). Note: To operate this feature, accessory delay must not be active. Opening the Windows You can only open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows and vent the moonroof. Release the button once movement starts. Press the lock or unlock button to stop movement. Closing the Windows WARNING

When closing the windows and moonroof, you should verify they are free of obstructions and make sure

that children and pets are not in the proximity of the window openings.

To close the windows and moonroof, press and hold the remote control lock button. Release the button once movement starts. Press the lock or unlock button to stop movement. EXTERIOR MIRRORS Power Exterior Mirrors WARNING

Do not adjust the mirrors when your vehicle is moving.

73

Fusion/Mondeo (CC7)

Left-hand mirror Adjustment control Right-hand mirror

To adjust a mirror: 1. Select the mirror you want to adjust.

The control will illuminate.

2. Adjust the position of the mirror. 3. Press the mirror switch again. Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 126). Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Memory Function (page 132). Auto-Dimming Feature (If Equipped) The driver’s exterior mirror will automatically dim when the interior auto-dimming mirror is activated.

E144073Windows and Mirrors

Signal Indicator Mirrors (If Equipped) The outer portion of the appropriate mirror housing will blink when the turn signal is activated. Integrated Blind Spot Mirrors (If Equipped)

WARNING

Objects in the blind spot mirror are closer than they appear.

Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to increase your visibility along the side of your vehicle. Check the main mirror first before a lane change, then check the blind spot mirror. If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.

74

Fusion/Mondeo (CC7)

The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C). Blind Spot Monitor (If Equipped) See Blind Spot Monitor (page 197). INTERIOR MIRROR WARNING

Do not adjust the mirror when your vehicle is moving.

ABCE138665Windows and Mirrors

Illuminated Vanity Mirror

Lift the cover to switch the lamp on. MOONROOF (IF EQUIPPED)

WARNINGS

Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously

hurt themselves.

When closing the moonroof, you should verify that it is free of obstructions and make sure that

children and pets are not in the proximity of the roof opening.

The sliding shade can be manually opened or closed when the moonroof is closed. Pull the shade toward the front of the vehicle to close it. The moonroof controls are located on the overhead console and have a one-touch open and close feature. To stop it during one-touch operation, touch the control a second time.

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up. SUN VISORS

Rotate the sun visor toward the side window and extend it rearward for extra shade.

75

Fusion/Mondeo (CC7)

E138666E162197Windows and Mirrors

Open Vent Close

Opening and Closing the Moonroof Touch (A) to open the moonroof. It will stop short of the fully opened position. Note: This position helps to reduce wind noise or rumbling which may happen with the moonroof fully open. Touch (A) again to fully open the moonroof. Touch (C) to close the moonroof. Bounce-Back The moonroof will stop automatically and reverse some distance if an obstacle is detected while closing. Touch and hold (C) within two seconds of a bounce-back event to override this function. Venting the Moonroof Touch (B) to vent the moonroof. Touch (C) to close it.

76

Fusion/Mondeo (CC7)

E144499Instrument Cluster

GAUGES Type 1 and 2

Tachometer Information Display (Type 2 shown Type 1 similar) Speedometer Fuel Gauge Engine Coolant Temperature Gauge

Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled.

Outside Air Temperature Shows the outside air temperature. Compass Displays the vehicle’s heading direction. Trip Computer See General Information (page 83).

77

Fusion/Mondeo (CC7)

E144485Instrument Cluster

Vehicle Settings and Personalization See General Information (page 83). Engine Coolant Temperature Gauge Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the center section. If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down. Note: Do not restart the engine until the cause of overheating has been resolved. Type 3

WARNING

Never remove the coolant reservoir cap while the engine is running or hot.

Fuel Gauge Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when your vehicle is moving or on a gradient. The arrow adjacent to the fuel pump symbol indicates on which side of the vehicle the fuel filler door is located.

78

Fusion/Mondeo (CC7)

E144486Instrument Cluster

Left Information Display Speedometer Right Information Display See General Information (page 343).

Left Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. Trip Computer See General Information (page 83). Vehicle Settings and Personalization See General Information (page 83). WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle. Adaptive Cruise Control (If Equipped)

The speed control system indicator light changes color to indicate what mode the system is in: See Using Cruise Control (page 186). On (white light): Illuminates when the adaptive cruise control system is turned on. Turns off when the speed control system is turned off.

Engaged (green light): Illuminates when the adaptive cruise control system is engaged. Turns off when the speed control system is disengaged. Anti-Lock Braking System

If it illuminates when you are driving, this indicates a malfunction. You will continue

to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer. Auto Start-stop (If Equipped)

It will illuminate to inform you when the engine shuts down or in conjunction with a message.

Battery

If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical

equipment and have the system checked by your authorized dealer immediately. Blind Spot Monitor (If Equipped)

It will illuminate when you switch this feature off or in conjunction with a message. See Blind Spot

Monitor (page 197). See Information Messages (page 91). Brake System

It will illuminate when you engage the parking brake with the ignition on.

79

Fusion/Mondeo (CC7)

E144524E151262E144522Instrument Cluster

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.

WARNING

Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control (If Equipped)

It will illuminate when you switch this feature on.

Direction Indicator

Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the

indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 257). Door Ajar

Displays when the ignition is on and any door is not completely closed.

Electric Park Brake

It will illuminate or flash when the electric parking brake has a malfunction.

Engine Coolant Temperature

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as

possible, switch off the engine and let cool. Engine Oil

If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 246). Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately. Fasten Safety Belt

It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety

Belt Minder (page 29). Front Airbag

If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer. Front Fog Lamps (If Equipped)

It will illuminate when you switch the front fog lamps on.

80

Fusion/Mondeo (CC7)

E71340E146190Instrument Cluster

Heads Up Display (If Equipped) A red beam of lights will illuminate on the windshield in certain instances when using

adaptive cruise control and/or the collision warning system. It will also illuminate momentarily when you start your vehicle to make sure the display works. High Beam

It will illuminate when you switch the high beam headlamps on. It will flash when you use the

headlamp flasher. Hood Ajar

Displays when the ignition is on and the hood is not completely closed.

Lane Keeping Aid (If Equipped)

Illuminates when the lane keeping system is activated.

Low Fuel Level

It will illuminate when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as

possible. Low Tire Pressure Warning

It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check

your tire pressure as soon as possible.

It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer. Parking Lamps

It will illuminate when you switch the parking lamps on.

Powertrain Fault

Illuminates when a powertrain or an AWD fault has been detected. Contact your

authorized dealer as soon as possible. Service Engine Soon

If the service engine soon indicator light stays illuminated after the engine is started, it

indicates that the On Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On board diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 157). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components.

81

Fusion/Mondeo (CC7)

E156133E159324E144813Instrument Cluster

AUDIBLE WARNINGS AND INDICATORS Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position. Keyless Warning Alert (If Equipped) Chirps the horn twice when you exit the vehicle and the keyless vehicle is in RUN, indicating the vehicle is still on. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately.

The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 157). Stability Control

It will flash when the system is active. If it remains illuminated or does not illuminate when you

switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. See Using Stability Control (page 176). Stability Control Off

It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off. See Using Stability Control (page 176). Trunk Ajar

Displays when the ignition is on and the trunk is not completely closed.

82

Fusion/Mondeo (CC7)

E138639E159323Information Displays

GENERAL INFORMATION

WARNING

Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle. We recommend against the use of any handheld device while driving and that you comply with all applicable laws.

Note: Your vehicle may or may not be equipped with all the messages listed in this chapter. Your vehicle will not display messages of systems it is not equipped with. Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display.

Information Display Controls (Type 1 and Type 2)

• Press the up and down arrow buttons

to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a

sub-menu.

• Press the left arrow button to exit a

menu.

• Press and hold the left arrow button at

any time to return to the main menu display (escape button).

• Press the OK button to choose and

confirm settings or messages.

Menu You can access the menu using the information display control. Note: Some options may appear slightly different or not at all if the items are optional.

Trip Odometer Trip Timer Fuel Used Average Fuel

Fusion/Mondeo (CC7)

Trip 1 and 2

83

E144637Information Displays

Trip 1 and 2

• •

All Values Outside Temperature • Resetting the Trip Computer — Press and hold OK on the current screen to reset the

respective trip, distance, time and fuel information. Trip Odometer — Registers the distance of individual journeys. Trip Timer — timer stops when the vehicle is turned off and restarts when the vehicle is restarted. Fuel Used — shows the amount of fuel used for a given trip.

• • Average Fuel — shows the average fuel economy for a given trip. • All Values — Shows all trip values. • Outside Temperature — Shows the outside air temperature.

Distance to E Inst Fuel Econ Long Term Average Fuel Fuel History All Values

Auto Stop/Start

Intelligent AWD MyKey System Check

Fuel Economy

Information

Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 91). All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.

84

Fusion/Mondeo (CC7)

Information Displays

Settings

On or Off On (default on key cycle) or Off On or Off On or Off

Driver Assist

Vehicle

Traction Ctrl Blind Spot Rear Park Aid Hill Start Assist Cross Traffic Auto Engine Off Fuel History Lighting

On or Off

5, 10 or 30 minutes Auto Highbeam Autolamp Delay

Settings (cont’d)

Autolock Autounlock Relock Mislock Remote Unlock

Set to XXX %

Remote Open / Remote Close Courtesy Wipe / Rain Sensing Hold OK to Create MyKey Always On / User Selectable Always On / User Selectable

Choose desired speed or Off

85

Vehicle (cont’d)

Locks

Oil Life Rest Switch Inhibit Windows Wipers Create MyKey 911 Assist Traction Control Max Speed

MyKey

Fusion/Mondeo (CC7)

Off or XX Seconds

All Doors / Driver First

Information Displays

Speed Minder Volume Limiter Do Not Disturb Clear MyKeys Language Units

Settings (cont’d)

Choose desired speed or Off On or Off

On or Off

Hold OK to Clear All MyKeys Choose your applicable setting Distance

Temperature

Display

Choose your applicable setting Choose your applicable setting

Information Display Controls (Type 3)

Main menu From the main menu bar on the left side of the information display, you can choose from the following categories:

Display Mode

Trip 1 & 2

Fuel Economy

Information

Settings

Scroll up/down to highlight one of the categories, then press the right arrow key or OK to enter into that category. Press the left arrow key as needed to exit back to the main menu.

• Press the up and down arrow buttons

to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a

sub-menu.

• Press the left arrow button to exit a

menu.

• Press and hold the left arrow button at

any time to return to the main menu display (escape button).

• Press the OK button to choose and

confirm settings or messages.

86

Fusion/Mondeo (CC7)

E144638E144639E138660E144640E144642E100023Information Displays

Display Mode

Use the up/down arrow buttons to choose between the following display options.

Display mode

Option 1

Option 2

Option 3

Option 4

XXX mi (km) to empty Fuel gauge Round tachometer Vertical tachometer Engine coolant temp gauge • XXX mi (km) to empty: Shows the approximate distance the vehicle will travel. •

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When the fuel level becomes low, the level indicator will change to amber. When the fuel level becomes critically low, the level indicator will change to red. Note: When a MyKey® is in use, low fuel warnings will display earlier. The fuel icon and arrow indicates which side of the vehicle the fuel filler door is located.

• Round tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. During SelectShift Automatic™ transmission (SST) use, the currently selected gear will appear in the display. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.

•

Trip 1 & 2

Choose between the standard or enhanced trip display.

Trip 1 & 2

Standard display

Enhanced display

Trip Odometer Trip Timer Average Fuel

87

Fusion/Mondeo (CC7)

E144639E138660Information Displays

Trip 1 & 2

Standard display

Enhanced display

Fuel Used Press and hold OK to reset the currently displayed trip information.

• •

Trip Odometer — shows the accumulated trip distance. Trip Timer— timer stops when the vehicle is turned off and restarts when the vehicle is restarted.

• Average Fuel — shows the average fuel economy for a given trip. •

Fuel Used — shows the amount of fuel used for a given trip.

Fuel Economy

Use the left/right arrow buttons to choose the desired fuel economy display.

Fuel Economy

Option 1

Option 2

DTE Inst Fuel Econ Average Fuel Fuel History Fuel History Duration • DTE: Distance To Empty shows the approximate distance the vehicle will travel on

5, 10, or 30 minute

the fuel remaining in the tank. Changes in driving pattern may cause the value to vary. Inst Fuel Econ: This display shows a visual graph of your instantaneous fuel economy.

• • Average Fuel: Indicates the average fuel consumption since the function was last

reset. Fuel History: shows a bar chart of your fuel history. Fuel History Duration: shows fuel usage over a 5, 10, or 30 minute time span.

• •

Info

In this mode, you can view different vehicle system information and perform a

system check.

88

Fusion/Mondeo (CC7)

E144640E144642Information Displays

Auto Stop/Start

Driver Alert MyKey System Check

Information

Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 91). All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.

Settings

In this mode, you can configure different driver setting choices.

Note: Some items are optional and may not appear.

Driver Assist

Traction Ctrl Blindspot Collision Warning

Settings On / Off On (default on key cycle) / Off Sensitivity Distance Alert Warn

High / Normal / Low On / Off On (default on key cycle) / Off

Cruise Control Cross Traffic Driver Alert Hill start

Adaptive (default on key cycle) or Normal On (default on key cycle) / Off On / Off On / Off

Settings (cont’d)

Driver Assist (cont’d)

Lane Keeping System

Front Park Aid

Mode Intensity On (default on key cycle) / Off

Alert / Aid / Both High / Normal / Low

89

Fusion/Mondeo (CC7)

E100023Information Displays

Settings (cont’d)

Vehicle

Rear Park Aid Auto Engine Off Easy Entry/Exit Lighting

Locks

Oil Life Reset

On (default on key cycle) / Off On (default on key cycle) / Off On / Off Auto Highbeam Autolamp Delay Autolock Autounlock Mislock Remote Unlocking Set to XXX %

Off or XX Seconds On / Off On / Off On / Off All doors / Driver’s door

Settings (cont’d)

Climate Control (using this feature allows you to select different climate control modes when the vehicle is started using the remote start feature)

Duration Quiet Start System

Settings (cont’d)

On / Off Remote Open Remote Close

90

Heater – A/C: Auto / Last Settings Front Defrost: Auto / Off Rear Defrost: Auto / Off Driver Seat: Auto / Off Passenger Seat: Auto / Off 5 / 10 /15 minutes On / Off Enable / Disable

On / Off On / Off

Vehicle (cont’d)

Remote Start

Vehicle (cont’d)

Switch Inhibit Windows

Fusion/Mondeo (CC7)

Information Displays

MyKey

Display

Wipers

Create MyKey 911 Assist Traction Control Max Speed Speed Minder Volume Limiter Do Not Disturb Clear MyKeys Language Units

On / Off On / Off

Settings (cont’d) Courtesy Wipe Rain Sensing Hold OK to Create MyKey Always On / User Selectable Always On / User Selectable Choose desired speed or off Choose desired speed or off On / Off Always On / User Selectable Hold OK to Clear All MyKeys Choose your applicable setting Distance

Temperature

Gauge Display

Fuel Gauge / Fuel + Tach

INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have.

Choose your applicable setting Choose your applicable setting

Press the OK button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time.

91

Fusion/Mondeo (CC7)

E144636Information Displays

Certain messages need to be confirmed Active Park

before you can access the menus.

Message

Active Park Fault

Action

Displayed when the system needs service. Contact your

authorized dealer as soon as possible.

Adaptive Cruise Control

Message

Adaptive Cruise

Malfunction

Adaptive Cruise Not

Available

Adaptive Cruise Not

Available Sensor

Blocked See Manual

Cruise Control Auto- matic Braking Turned

Off

Front Sensor Not Aligned

Adaptive Cruise - Driver

Resume Control

Adaptive Cruise Speed Too Low to Activate Adaptive Cruise Shift

Down

Action

Displayed when a radar malfunction is preventing the ACC from engaging. See Using Adaptive Cruise Control (page

187).

Displayed when conditions exist such that the adaptive cruise

cannot function properly. See Using Adaptive Cruise

Control (page 187).

Displayed when the radar is blocked because of poor radar visibility due to bad weather or ice/mud/water in front of radar. Driver can typically clean the sensor to resolve. See

Using Adaptive Cruise Control (page 187).

Displayed when the automatic braking has been disabled.

Displayed when a radar malfunction is preventing the ACC

from engaging.

Displayed when the adaptive cruise has reinstated controls

to the driver.

Displays when the vehicle speed is too slow to activate the

adaptive cruise.

Displays when the adaptive cruise is automatically adjusting the gap distance and the driver needs to shift the transmission

into a lower gear.

92

Fusion/Mondeo (CC7)

Information Displays

Action

Displays when the system detects a malfunction due to a

blocked sensor.

Displayed when the traction control has been disabled or

enabled by the driver.

Action

Displays when the system detects a malfunction due to a

blocked sensor.

AdvanceTrac® Message

Service AdvanceTrac

AdvanceTrac Off On

Airbag

Message

Occupant Sensor BLOCKED Remove

Objects Near Passenger

Seat

Alarm

Message

Action

Vehicle Alarm to Stop Alarm, Start Vehicle

Displays when the alarm has been triggered due to unauthor-

ized entry. See Anti-Theft Alarm (page 61).

Auto Start-Stop

Message

Auto StartStop Press Brake to Start Engine Auto StartStop Press

Brake Harder to Activate

Auto StartStop Press Clutch to Start Engine Auto StartStop Press

Any Pedal

Auto StartStop Select Neutral To Start Engine

Action

The engine needs to be restarted, press the brake pedal to

start.

The engine needs to be restarted, press the brake pedal harder

to start.

The engine needs to be restarted, press the clutch pedal to

start.

The engine needs to be restarted, press any pedal to start.

Select neutral for the system to restart the engine.

93

Fusion/Mondeo (CC7)

Information Displays

Message

Auto StartStop Shift to

P Restart Engine

Action

Select park for the system to restart the engine.

Auto StartStop Manual

Restart Required Auto StartStop Not

Available

The system is not functioning. A manual restart is required.

Displays when conditions are not met for the Auto StartStop

system to function properly See Start-Stop (page 150).

Engine Stopped

StartStop has shutoff the engine automatically.

Engine On due to Vehicle

Maneuvering

The wheels are at a sharp angle or the steering wheel is being

turned.

Engine On due to

Steering Wheel Maneuv-

ering

Engine On due to Accessory Usage

Engine On Normal Oper-

ation

The wheels are at a sharp angle or the steering wheel is being

turned.

Engine may be on to support high demand for electrical

accessories, such as operating power windows, rear defroster,

or when using the power point.

Engine is on to support normal vehicle operation. Includes external vehicle conditions, such as altitude, traffic, low

ambient temperature. Also includes battery outside optimal operating conditions (state of charge and temperature), and

inadequate brake vacuum (can occur if the brake pedal is

depressed a number of times in succession).

Heating or Cooling

Power Outlet in Use

Engine is on to achieve or maintain interior compartment at

an acceptable level.

Engine is on, which is required to support the use of the power

outlet (110V).

Automatic Engine Shutdown

Message

Engine Shuts Off in XX

Seconds

Engine Shut Off for Fuel

Economy

Engine Shuts Off in XX Seconds Press Ok to

Override

Action

Displays when the engine is getting ready to shut off.

Displays when the engine has shut off to help increase fuel

economy.

Displays when the engine is getting ready to shut off. You can press OK on the left steering wheel button to override the shut

down.

94

Fusion/Mondeo (CC7)

AWD

Message

AWD Temporarily

Disabled AWD Off

AWD Restored

AWD Malfunction Service Required

Information Displays

Action

Displayed when the AWD system has been temporarily

disabled to protect itself from overheating.

Displayed when the AWD system has been automatically disabled to protect itself. This is caused by operating the

vehicle with the compact spare tire installed or if the system

is overheating.

The AWD system will resume normal function and clear this message after driving a short distance with the road tire re-

installed or after the system is allowed to cool.

Displayed in conjunction with the Throttle Control/Transmis- sion/AWD light when the AWD system is not operating prop- erly. If the warning stays on or continues to come on, contact

your authorized dealer as soon as possible.

Battery and Charging System

Message

Check Charging System

Low Battery Features Temporarily Turned Off

Turn Power Off to Save

Battery

Action

Displayed when the charging system needs servicing. If the

warning stays on or continues to come on, contact your

authorized dealer as soon as possible.

Displayed when the battery management system detects an extended low-voltage condition. Various vehicle features will be disabled to help preserve the battery. Turn off as many of the electrical loads as soon as possible to improve system voltage. If the system voltage has recovered, the disabled

features will operate again as normal

Displayed when the battery management system determines that the battery is at a low state of charge. Turn the ignition off as soon as possible to protect the battery. This message will clear once the vehicle has been started and the battery state of charge has recovered. Turning off unnecessary elec- trical loads will allow faster battery state-of-charge recovery.

95

Fusion/Mondeo (CC7)

Information Displays

Blind Spot Information and Cross Traffic Alert System

Message

Action

Blindspot System Fault

Displayed when a fault with the system has occurred. Contact

your authorized dealer as soon as possible.

Blindspot Not Available

Sensor Blocked See

Manual

Displayed when the system sensors are blocked. Contact your

authorized dealer as soon as possible. See Blind Spot

Monitor (page 197).

Cross Traffic Vehicle

Coming From X

Cross Traffic Not Avail- able Sensor Blocked See

Manual

Displayed when the system detects a vehicle. See Blind Spot

Monitor (page 197).

Displayed when the blind spot information system and cross

traffic alert system sensors are blocked. See Blind Spot

Monitor (page 197).

Cross Traffic System

Fault

Displays when a fault with the system has occurred. Contact

your authorized dealer as soon as possible.

Collision Warning System

Message

Collision Warning

Malfunction

Collision Warning Not

Available Sensor

Blocked See Manual

Action

Displayed when there is a system malfunction with the colli- sion warning system. The system will be disabled. Contact

your authorized dealer as soon as possible.

Displayed when the collision warning system radar is blocked because of poor radar visibility due to bad weather or ice/ mud/water in front of the radar. Driver can typically clean the sensor to resolve. Contact your authorized dealer as soon as

possible.

Collision Warning Not

Available

Displayed when there is a system malfunction with the colli- sion warning system. The system will be disabled. Contact

your authorized dealer as soon as possible.

96

Fusion/Mondeo (CC7)

Information Displays

Action

Displays when the door(s) listed is not completely closed and

the vehicle is moving.

Displays when the door(s) listed is not completely closed. Displays when the luggage compartment is not completely

closed.

Displays when the door switches have been disabled.

Displayed when there is a system malfunction with the child locks. Contact your authorized dealer as soon as possible. Displays the factory keypad code after the keypad has been

reset.

Action

Stop and rest as soon as it is safe to do so.

Take a rest break soon.

Action

Doors and Locks

Message X Door Ajar

Trunk ajar

Switches Inhibited

Security Mode

Child Lock Malfunction

Service Required

Factory Keypad Code

XXXXX

Driver Alert

Message

Driver Alert Warning Rest

Now

Driver Alert Warning Rest

Suggested

Fuel

Message

Fuel Level Low

Displayed as an early reminder of a low fuel condition.

Check Fuel Fill Inlet

Displayed when the fuel fill inlet may not be properly closed.

Hill Start Assist

Message

Action

Hill Start Assist Not

Available

Displays when hill start assist is not available. Contact your

authorized dealer. See Hill Start Assist (page 164).

97

Fusion/Mondeo (CC7)

Information Displays

Keys and Intelligent Access

Message

Press Brake to START

No Key Detected

Restart Now or Key is

Needed

Action

Displayed as a reminder to press the brake while starting the

vehicle.

Displayed if the key is not detected by the system. See

Keyless Starting (page 144).

Displayed when the StartStop button is pressed to shut off the engine and an Intelligent Access key is not detected inside

the vehicle.

Run Power Active

Displayed when the vehicle is in the run ignition state.

Starting System Fault

This message is displayed when there is a problem with your

vehicle’s starting system. See your authorized dealer for

service.

Press Brake and Clutch

to Start

Press Clutch to Start

Cranking Time Exceeded

Key Program Successful

Key Program Failure

Displayed as a reminder to press the brake and clutch while

starting the vehicle.

Displayed as a reminder to press the clutch in while starting

the vehicle.

Displays when the starter has exceeded its cranking time in

attempting to start the vehicle.

Displayed during spare key programming, when an intelligent

access key is programmed to the system.

Displayed during spare key programming, when an intelligent

access key has failed to be programmed.

Max Number of Keys

Learned

Displayed during spare key programming when the maximum

number of keys have been programmed.

Not Enough Keys

Learned

Displayed during spare key programming when not enough

keys have been programmed.

Key Battery Low Replace

Soon

Could Not Program

Integrated Key

Engine On

Displays when the key battery is low. Change the battery as

soon as possible.

Displayed when an attempt is made to program a spare key

using two existing keys.

Displays to inform the driver that they are exiting the vehicle

and the engine is on.

98

Fusion/Mondeo (CC7)

Information Displays

Lane Keeping System

Message

Lane Keeping Sys. Malfunction Service

Required

Action

The system has malfunctioned. Contact your authorized

dealer as soon as possible.

Front Camera Tempor-

arily Not Available

The system has detected a condition that has caused the

system to be temporarily unavailable.

Front Camera Low Visib-

ility Clean Screen

The system has detected a condition that requires the wind-

shield to be cleaned to operate properly.

Front Camera Malfunc- tion Service Required Keep Hands on Steering

Wheel

The system has malfunctioned. Contact your authorized

dealer as soon as possible.

Displayed when the system requests the driver to keep their

hands on the steering wheel.

Maintenance Message

LOW Engine Oil Pressure

Action

Stop the vehicle as soon as safely possible, turn off the engine.

Check the oil level. If the warning stays on or continues to come on with your engine running, contact your authorized

dealer as soon as possible.

Change Engine Oil Soon

Oil Change Required

Brake Fluid Level LOW

Check Brake System

Engine Coolant Overtem-

perature

Displayed when the engine oil life remaining is 10% or less.

See Engine Oil Check (page 246).

Displayed when the oil life left reaches 0%. See Engine Oil

Check (page 246).

Indicates the brake fluid level is low and the brake system should be inspected immediately. See Brake Fluid Check

(page 250).

Displays when the brake system needs servicing. Stop the

vehicle in a safe place. Contact your authorized dealer.

Displays when the engine temperature is too high. Stop the vehicle in a safe place and allow the engine to cool. If the problem persists, contact your authorized dealer. See Engine

Coolant Check (page 247).

99

Fusion/Mondeo (CC7)

Information Displays

Message

Power Reduced to Lower Engine Temp Transport / Factory

Mode

See Manual

Action

Displays when the engine has reduced power in order to help

reduce high coolant temperatures.

Displays to indicate that the vehicle is still in Transport or Factory mode. This may not allow some features to operate

properly. See your authorized dealer.

Informs the driver that the powertrain needs service due to a

powertrain malfunction.

MyKey

Message

MyKey Not Created

MyKey Active Drive

Safely

Speed Limited to XX

MPH/km/h

Near Vehicle Top Speed

Vehicle at Top Speed of

MyKey Setting

Check Speed Drive

Safely

Buckle Up to Unmute

Audio

AdvanceTrac On -

MyKey Setting

Traction Control On -

MyKey Setting

MyKey Park Aid Cannot