2013 Ford Fusion Owners Manual

Note: You can switch temperature units between Fahrenheit and Celsius. See Settings (page 355).

AUTO: Press the button to turn on fully automatic operation. Select the desired temperature using the temperature control. The system automatically adjusts fan speed, air distribution, A/C operation, and outside or recirculated air, to heat or cool the vehicle to maintain the selected temperature. CLIMATE: Press to turn the climate control system on and off. When the system is off, outside air cannot enter the vehicle. MAX A/C: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle. Recirculated air may turn off automatically in all airflow modes except MAX A/C to reduce the possibility of fogging. A/C: Press the button to turn air conditioning off and on. To improve air conditioning when starting your vehicle, drive with the windows slightly open for two to three minutes. Use A/C with recirculated air to improve cooling performance and efficiency. Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle. Recirculated air may turn off automatically in all airflow modes except MAX A/C to reduce the possibility of fogging.

123

Fusion/Mondeo (CC7)

E144494Climate Control

Passenger temperature control: Allows the passenger to set their temperature independent of the driver temperature. Press + or - to increase or decrease the air temperature on the passenger side of the vehicle when in dual zone mode. Fan speed control: Press the small fan icon or large fan icon to decrease or increase the volume of air circulated in your vehicle. Driver temperature control: Press + or - to increase or decrease the air temperature inside the vehicle. This control also adjusts the passenger side temperature when dual zone operation is disengaged. MAX Defrost: Press to switch on. The system distributes outside air through the windshield air vents, the air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. When MAX defrost is on, recirculated air cannot be selected (to prevent fogging). The heated rear window is automatically switched on when MAX defrost is selected. Heated rear window: Turns the heated rear window on and off. See Heated Windows and Mirrors (page 126). Defrost: Distributes air through the windshield defroster vents and de-mister vents. You can also use this setting to defog and clear the windshield of a thin covering of ice.

HINTS ON CONTROLLING THE INTERIOR CLIMATE General Hints Note: Prolonged use of recirculated air may cause the windows to fog up. Note: You may feel a small amount of air from the footwell air vents regardless of the air distribution setting. Note: To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on. Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Note: Remove any snow, ice or leaves from the air intake area at the base of the windshield.

Manual Climate Control Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position. Automatic Climate Control Note: Adjusting the settings when your vehicle interior is extremely hot or cold is not necessary. The system automatically adjusts to heat or cool the cabin to your selected temperature as quickly as possible. For the system to function efficiently, the instrument panel and side air vents should be fully open. Note: At low ambient temperatures with AUTO selected, the system directs airflow to the windshield and side window vents and fan may run at a slow speed until the engine warms up.

124

Fusion/Mondeo (CC7)

Climate Control

Heating the Interior Quickly

Vehicle With Manual Climate Control

Adjust the fan speed to the highest speed setting. Adjust the temperature control to the highest setting (not MAX defrost). Select the footwell air vents using the air distribution buttons.

Recommended Settings for Heating Vehicle With Manual Climate Control

Adjust the fan speed to the center setting. Adjust the temperature control to the midway point of the hot settings (not MAX defrost). Select the footwell air vents and wind- shield air vents position using the air distribution buttons.

Cooling the Interior Quickly

Vehicle With Manual Climate Control Adjust the temperature control to the MAX A/C position. Drive with the windows open for 2-3
minutes.

Vehicle With Automatic Climate Control Press the AUTO button.

Adjust the temperature control to the desired setting.

Vehicle With Automatic Climate Control Press the AUTO button.

Adjust the temperature to a comfortable setting.

Vehicle With Automatic Climate Control Adjust the temperature control to the desired setting.

125

Fusion/Mondeo (CC7)

Climate Control

Recommended Settings for Cooling Vehicle With Manual Climate Control

Adjust the fan speed to the middle speed setting. Adjust the temperature control to the midway point of the cold settings. Select the instrument panel air vents using the air distribution buttons.

Vehicle With Automatic Climate Control Press the AUTO button.

Adjust the temperature to a comfortable setting.

Side Window Defogging in Cold Weather

Vehicle With Automatic Climate Control Press the defrost button.

Adjust the temperature control to the desired setting.

Press the button to clear the rear window of thin ice and fog. Press the button again within 10 minutes to switch it off. It switches off automatically after 10
minutes, or when you switch the ignition off. Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window. This may cause damage to the heated grid lines. Your warranty does not cover this damage.

Vehicle With Manual Climate Control

Select the instrument panel and footwell air vents positions through the air distri- bution control. Press the A/C button.

Adjust the temperature control to the desired setting. Adjust the fan speed to the highest setting. Direct the instrument panel side air vents toward the side windows. Close the instrument panel center vents.

HEATED WINDOWS AND MIRRORS (IF EQUIPPED) Heated Rear Window Note: You must switch the ignition on to use this feature.

126

Fusion/Mondeo (CC7)

Climate Control

heated seats heated mirrors heated rear window.

REMOTE START (IF EQUIPPED) The climate control system adjusts the cabin temperature during remote start. You cannot adjust the system during remote start operation. Turn the ignition on to return the system to its previous settings. You can now make adjustments. You need to turn certain vehicle-dependent features back on, such as: • • • You can adjust the settings using the information display controls. See Information Displays (page 83). Automatic Settings You can set the climate control to operate in AUTO mode through the information display setting: Remote Start > Climate Control > Heater-A/C > Auto. The climate control system automatically sets the interior temperature to 72°F (22°C). In hot weather, the system is set to 72°F (22°C). In moderate weather, the system either heats or cools (based on previous settings). The rear defroster, heated mirrors and heated seats do not automatically turn on. In cold weather, the system is set to 72°F (22°C). The heated seats are set to high (if available, and selected to AUTO in the information display). The rear defroster and heated mirrors automatically turn on.

Heated Exterior Mirror (If Equipped) Note: Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass that has frozen in place. These actions could cause damage to the glass and mirrors. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. The heated mirrors remove ice, mist and fog when you switch on the heated rear window. CABIN AIR FILTER Your vehicle is equipped with a cabin air filter. It is located behind the glove box. The particulate filtration system reduces the concentration of airborne particles such as dust, spores and pollen in the air supplied to the interior of your vehicle. Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. The particulate filtration system gives you and your passengers the following benefits: •

It improves your driving comfort by reducing particle concentration. It improves the interior compartment cleanliness. It protects the climate control components from particle deposits.

•

•

Replace the filter at regular intervals. See Scheduled Maintenance (page 428). For additional cabin air filter information, or to replace the filter, see an authorized dealer.

127

Fusion/Mondeo (CC7)

Climate Control

Last Settings You can set the climate control to operate using the last climate control settings through the information display setting: Remote Start > Climate Control > Heater–A/C > Last Settings. The climate control system automatically uses the settings last selected before you turned off the engine. Heated and Cooled Devices The climate control system controls other heated and cooled devices inside the vehicle. You can switch these devices on (if available, and selected to AUTO in the information displays) during remote start. Heated devices usually switch on during cold weather, and cooled devices during hot weather.

128

Fusion/Mondeo (CC7)

Seats

We recommend that you follow these guidelines: •

Sit in an upright position with the base of your spine as far back as possible.

• Do not recline the seat back more than

30 degrees.

• Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 inches (25 centimeters) between your breastbone and the air bag cover.

•

• Hold the steering wheel with your arms

slightly bent. Bend your legs slightly so that you can press the pedals fully.

•

• Position the shoulder strap of the safety belt over the center of your shoulder and position the lap strap tightly across your hips.

Make sure that your driving position is comfortable and that you can maintain full control of your vehicle. HEAD RESTRAINTS WARNINGS

Fully adjust the head restraint before you sit in or operate your vehicle. This will help minimize the risk of neck injury in the event of a collision. Do not adjust the head restraint when your vehicle is moving.

The head restraint is a safety device. Whenever possible it should be installed and properly adjusted when

the seat is occupied.

SITTING IN THE CORRECT POSITION

WARNINGS

Sitting improperly, out of position or with the seat back reclined too far can take weight off the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in the event of a crash. Always sit upright against your seat back, with your feet on the floor.

Do not recline the seat back as this can cause the occupant to slide under the safety belt, resulting in

serious injury in the event of a crash.

Do not place objects higher than the seat back to reduce the risk of serious injury in the event of a crash

or during heavy braking.

When you use them properly, the seat, head restraint, safety belt and air bags will provide optimum protection in the event of a crash.

129

Fusion/Mondeo (CC7)

E68595Seats

WARNINGS

Install the head restraint properly to help minimize the risk of neck injury in the event of a collision.

Note: Adjust the seat back to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position. Front seat and rear seat outboard head restraints

Rear center head restraint

The head restraints consist of:

An energy absorbing head restraint Two steel stems Guide sleeve adjust and unlock button Guide sleeve unlock and remove button

Adjusting the Head Restraint Raising the Head Restraint Pull the head restraint up. Lowering the Head Restraint 1. Press and hold button C. 2. Push the head restraint down. Removing the Head Restraint 1. Pull the head restraint up until it

reaches its highest position.

2. Press and hold buttons C and D. 3. Pull the head restraint up. Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until in locks. Tilting Head Restraints The front head restraints have a tilting feature for extra comfort. To tilt the head restraint, do the following:

130

Fusion/Mondeo (CC7)

E138642E138645Seats

The manual front seats may consist of:

1. Adjust the seat back to an upright

driving or riding position.

2. Pivot the head restraint forward toward

your head to the desired position. After the head restraint reaches the forward-most tilt position, pivoting it forward again will then release it to the rearward, un-tilted position. MANUAL SEATS

WARNINGS

Do not adjust the driver's seat or seat back when your vehicle is moving. Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged. Reclining the seat back can cause an occupant to slide under the seat's safety belt, resulting in severe

personal injuries in the event of a collision.

a bar to move the seat backward and forward a control to adjust the lumbar of the seat back a lever to adjust the height of the seat a lever to adjust the angle of the seat back

POWER SEATS (IF EQUIPPED)

WARNINGS

Do not adjust the driver's seat or seat back when your vehicle is moving. Do not place cargo or any objects behind the seat back before returning it to the original position.

131

Fusion/Mondeo (CC7)

E144727ABCDE144631Seats

Power Lumbar (If Equipped)

MEMORY FUNCTION (IF EQUIPPED)

WARNINGS

Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of

obstructions and that all occupants are clear of moving parts.

Do not use the memory function when your vehicle is moving.

This feature will automatically recall the position of the driver's seat and power mirrors. The memory control is located on the driver’s door.

132

Fusion/Mondeo (CC7)

E144632E144633Seats

Linking a Pre-Set Position to your Remote Control or Intelligent Access Key Your vehicle can save the pre-set memory positions for up to three remote controls or intelligent access (IA) keys. 1. With the ignition on, move the memory

positions to the desired positions. 2. Press and hold the desired pre-set

button for about five seconds. A chime will sound after about two seconds. Continue holding until a second chime is heard.

3. Within three seconds, press the lock button on the remote control you are linking. A single chime will sound. To unlink a remote control, follow the same procedure – except in step 3, press the unlock button on the remote control. Note: To stop seat movement during a recall, press any driver seat adjustment control, any of the memory buttons, or any mirror control switch. Seat movement will also stop if you move your vehicle. Note: If more than one linked remote control or IA key is in range, the memory function will move to the settings of the first key stored. Easy Entry and Exit Function If you enable the easy entry and exit feature, it automatically moves the driver seat position rearward up to five centimeters when the transmission selector lever is in position P and the key is removed or the keyless start ignition is turned off. The driver seat will return to the previous position when the key is put in the ignition or the keyless start ignition is activated.

Saving a Pre-Set Position 1. Switch the ignition on. 2. Adjust the seat and exterior mirrors to

your desired position.

3. Press and hold the desired pre-set

button until you hear a single chime.

Up to three pre-set memory positions may be saved. A memory pre-set may be saved at any time. Recalling a Pre-Set Position Press and release the pre-set button associated with your desired driving position. The seat and mirrors will move to the position stored for that pre-set. Note: A pre-set memory position can only be recalled when the ignition is off, or when the transmission selector lever is in position P or N (and your vehicle is not moving) if the ignition is on. A pre-set memory position can also be recalled by pressing the unlock button on your remote control or intelligent access key if it is linked to a pre-set position, or by a driver door handle unlock with an intelligent access key present.

133

Fusion/Mondeo (CC7)

E142554Seats

You can turn off the easy entry and exit feature by using the driver information display. REAR SEATS Note: Your vehicle may have split seat backs that must be folded individually. To lower the seat back(s) from inside the vehicle, do the following:

3. Stow the safety belt in the stowage clip. This will prevent the safety belt from getting caught in the seat latch. When raising the seat back(s), make sure you hear the seat latch into place.

1. Pull the handle to release the seat

back.

2. Push the seat back forward.

134

Fusion/Mondeo (CC7)

E144634E164098Seats

HEATED SEATS (IF EQUIPPED)

WARNING

People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal

cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the heated seat if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

VENTILATED SEATS (IF EQUIPPED) The ventilated seats will only function when the engine is running. To operate the ventilated seats:

Press the ventilated seat symbol to cycle through the various cooling settings and off. Cooler settings are indicated by more indicator lights. If the engine falls below 350 RPM while the ventilated seats are on, the feature will turn itself off and will need to be reactivated. Heated and ventilated seat air filter replacement (if equipped) The climate controlled seat system includes air filters. You must replace them periodically. The filters are located under each front seat. You can access them from the second row foot-well area. Move the front seats all the way forward and to the full up positions to ease access.

Press the heated seat symbol to cycle through the various heat settings and off. Warmer settings are indicated by more indicator lights.

135

Fusion/Mondeo (CC7)

E146941E146309Seats

REAR SEAT ARMREST

To remove an air filter: 1. Turn the vehicle off. 2. Push up on the outside rigid edge of

the filter and rotate counterclockwise once the tabs are released, then remove the filter.

Fold the armrest down to use the armrest and cupholder.

To install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing.

2. Push in on the center of the outside

edge of the filter and rotate clockwise into the housing until it clips into position.

136

Fusion/Mondeo (CC7)

E146319E146321E144635Universal Garage Door Opener

HomeLink Wireless Control System (If Equipped)

WARNING

Do not use the system with any garage door opener that does not have the safety stop and reverse

feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982). A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death.

Note: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. Note: We recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the function button codes later in this section. Note: You can program a maximum of three devices. To change or replace any of the three devices after it has been initially programmed, you must first erase the current settings. See Erasing the function button codes later in this section.

The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. The system includes two primary features, a garage door opener and a platform for remote activation of devices within the home. As well as being programmed for garage doors, the system transmitter can be programmed to operate entry gate operators, security systems, entry door locks and home or office lighting. Additional system information can be found online at www.homelink.com or by calling the toll-free help line on 1-800-355-3515. In-vehicle programming This process is to program your hand-held transmitter and your in-vehicle HomeLink button. Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal.

1. With your vehicle parked outside of the

garage, turn your ignition to the on position, but do not start your vehicle.

2. Hold your hand-held garage door

transmitter 1–3 inches (2–8
centimeters) away from the HomeLink button you want to program.

137

Fusion/Mondeo (CC7)

E142657E142658Universal Garage Door Opener

3. Using both hands, simultaneously,

press and hold the desired HomeLink button and the hand-held transmitter button. DO NOT release either one until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing indicates successful training. 4. Press and hold the HomeLink button you programmed for five seconds, then release. You may need to do this twice to activate the door. If your garage door does not operate, watch the HomeLink indicator light.

If the indicator light stays on, the programming is complete. See Programming your garage door motor later in this section. If the indicator light flashes rapidly for 2
seconds and then turns to a constant light, the HomeLink button is not programmed yet. Do the following: Press and hold the HomeLink button while you press and release the hand-held transmitter button every 2 seconds. The HomeLink indicator light will flash slowly and then rapidly once the HomeLink function button recognizes and accepts the hand-held transmitter’s radio frequency signal. After programming the HomeLink button, begin programming your garage door opener motor. Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener.

138

Fusion/Mondeo (CC7)

To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515. Programming your garage door opener motor 1. Press the learn button on the garage

door opener motor and then you have 30 seconds to complete the next two steps.

2. Return to your vehicle.

3. Press and hold the function button you

want to program for 2 seconds, then release. Repeat this step. Depending on your brand of garage door opener, you may need to repeat this sequence a third time.

Erasing the Function Button Codes Note: You cannot erase individual buttons.

E142659E142658Universal Garage Door Opener

A. B.

Red indicator light Green indicator light

1. Press and hold one of the buttons on

the hand-held transmitter for 10
seconds. The indicator light will change from green to red and green.

2. Press the same button twice to confirm the change to programming mode. If done properly the indicator light will appear red.

3. Hold the transmitter within 1–3 inches (2–8 centimeters) of the button on the visor you want to program.

4. Press and hold both the programmed

Genie button on the hand-held transmitter and the button you want to program. The indicator light on the visor will flash rapidly when the programming is successful.

Note: The Genie transmitter will transmit for up to 30 seconds. If HomeLink does not program within 30 seconds the Genie transmitter will need to be pressed again. If the Genie transmitter indicator light displays green and red, release the button until the indicator light turns off before pressing the button again. Once HomeLink has been programmed successfully, the Genie transmitter must be changed out of program mode. To do this:

1. Press and hold the outer two function

buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly.

2. When the indicator lights flash, release the buttons. The codes for all buttons are erased.

Reprogramming a Single Button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do

NOT release the button.

2. The indicator light will begin to flash

after 20 seconds. Without releasing the button, follow Step 1 in the Programming section.

For questions or comments, contact HomeLink at www.homelink.com or 1-800-355-3515. Programming to a Genie Intellicode 2
Garage Door Opener Note: The Genie Intellicode 2 transmitter must already be programmed to operate with the garage door opener. Note: To program HomeLink to the transmitter you must first put the transmitter into programming mode.

139

Fusion/Mondeo (CC7)

E142660BAE142661Universal Garage Door Opener

5. Press and hold the previously

programmed button on the visor for 2
seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete. Clearing a HomeLink Device To erase programming from the three HomeLink buttons press and hold the two outer HomeLink buttons until the indicator light begins to flash. The indicator light will begin flashing in 10 to 20 seconds, at which time both buttons should be released. Programming has now been erased, and the indicator light should blink slowly to indicate the device is in train mode when any of the three HomeLink buttons are pressed. FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to your device not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment.

1. Press and hold the previously

programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green.

2. Press the same button twice to confirm

the change. If done correctly the indicator light will turn green.

Programming HomeLink to the Genie Intellicode Garage Door Opener Motor Note: You may need a ladder to access the garage door opener motor.

1. Press and hold the program button on

the garage door opener motor until both blue indicator lights turn on.

2. Release the program button. Only the smaller round indicator light should be on.

3. Press and release the program button.

The larger purple indicator light will flash.

Note: The next two steps must be completed in 30 seconds. 4. Press and release the Genie Intellicode

2 hand-held transmitter’s previously programmed button. Both indicator lights on the garage door opener motor unit should now flash purple.

140

Fusion/Mondeo (CC7)

E142662Auxiliary Power Points

12 Volt DC Power Point WARNING

Do not plug optional electrical accessories into the cigar lighter socket (if equipped). Improper use

of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury.

Note: If used when the engine is not running, the battery will discharge. There may be insufficient power to restart your engine. Note: Do not insert objects other than an accessory plug into the power point. This will damage the outlet and blow the fuse. Note: Do not hang any type of accessory or accessory bracket from the plug. Note: Do not use the power point over the vehicle capacity of 12 volt DC 180 watts or a fuse may blow. Note: Do not use the power point for operating a cigar lighter element. Note: Improper use of the power point can cause damage not covered by your warranty. Note: Always keep the power point caps closed when not in use. Run the engine for full capacity use of the power point. To prevent the battery from being discharged: • Do not use the power point longer than

necessary when the engine is not running.

• Do not leave devices plugged in

overnight or when the vehicle is parked for extended periods.

Locations Power points may be found:

Fusion/Mondeo (CC7)

in the front of the center console inside the center console storage bin on the rear of the center console.

• • • 110 Volt AC Power Point (If Equipped)

WARNING

Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design. Doing so my cause the power point to overload due to powering multiple devices that can reach beyond the 150 watt load limit and could result in fire or serious injury.

Note: Keep the engine running to use the power point.

The power point is used for powering electrical devices that require up to 150
watts. It is located on the rear of the center console. When the indicator light, located on the power point, is: •

on — power point is ready to supply power. off — power point power supply is off; ignition is not on. flashing — power point is in fault mode.

•

•

141

E143941Auxiliary Power Points

The power point temporarily turns off power if the 150 watt limit is exceeded. It can also switch to a fault mode when it is overloaded, overheated, or shorted. Unplug your device and switch the ignition off then on for overloading and shorting conditions. Let the system cool off, then turn the ignition off then on for an overheating condition. The power point is not designed for electric devices such as: • Cathode ray tube type televisions • Motor loads, for example vacuum cleaners, electric saws and other electric power tools, or compressor-driven refrigerators

• Measuring devices which process precise data, for example medical equipment or measuring equipment

• Other appliances requiring an

extremely stable power supply, for example microcomputer-controlled electric blankets or touch sensor lamps

142

Fusion/Mondeo (CC7)

Storage Compartments

CENTER CONSOLE Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. Available console features include:

Cupholder Storage compartment with auxiliary power point, auxiliary input jack, USB port and media hub Auxiliary power point

OVERHEAD CONSOLE

Press near the rear edge of the door to open it.

143

Fusion/Mondeo (CC7)

ABCE143942E75193Starting and Stopping the Engine

IGNITION SWITCH

GENERAL INFORMATION If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period.

0 (off) - The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. I (accessory) - Allows the electrical accessories, such as the radio, to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. II (on) - All electrical circuits are operational and the warning lamps and indicators illuminate. III (start) - cranks the engine. KEYLESS STARTING Note: The keyless starting system may not function if the key is close to metal objects or electronic devices such as cellular phones. Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine.

WARNINGS

Extended idling at high engine speeds can produce very high temperatures in the engine and

exhaust system, creating the risk of fire or other damage.

Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up

the engine compartment and exhaust system, creating the risk of fire.

Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.

If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes.

The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise. When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine.

144

Fusion/Mondeo (CC7)

E72128Starting and Stopping the Engine

Before starting the engine check the following: • Make sure all occupants have fastened

their safety belts.

• Make sure the headlamps and electrical accessories are off.

• Make sure the parking brake is on. • Move the transmission selector lever to position P (automatic transmission) or neutral (manual transmission). Turn the ignition key to position II. If your vehicle is equipped with a keyless ignition, see the following instructions.

•

Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. If your vehicle is equipped with a manual transmission, fully press the clutch pedal also.

2. Turn the key to position III to start the

engine. Release the key when the engine starts.

Note: The engine may continue cranking for up to 15 seconds or until it starts. Note: If you cannot start the engine on the first try, wait for a short period and try again. Vehicles with Keyless Start Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. 2. Press the button. The system does not function if: • • If you are unable to start the engine, do the following:

The key frequencies are jammed. The key battery has no charge.

Ignition Modes

The keyless starting system has three modes: • Off: Turns the ignition off.

• Without applying the brake pedal, press and release the button once when the ignition is in the on mode, or when the engine is running but the vehicle is not moving. • On: All electrical circuits are

operational and the warning lamps and indicators illuminate. • Without applying the brake pedal, press and release the button once.

• Start: Starts the engine.

• Press the brake pedal, and then

press the button for any length of time. An indicator light on the button illuminates when then ignition is on and when the engine starts.

STARTING A GASOLINE ENGINE When you start the engine, the idle speed increases, this helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer.

145

Fusion/Mondeo (CC7)

E144447Starting and Stopping the Engine

1. Fully press the brake pedal. If your vehicle is equipped with a manual transmission, fully press the clutch pedal also.

2. Fully press the accelerator pedal and

hold it there.

3. Start the engine. Note: You can crank the engine for a total of 60 seconds (without the engine starting) before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine three times for 20 seconds each time, without the engine starting, you reached the 60-second time limit. A message appears in the information display alerting you that you exceeded the cranking time. You cannot attempt to start the engine for at least 15 minutes. After 15 minutes, you are limited to a 15-second engine cranking time. You need to wait 60 minutes before you can crank the engine for 60 seconds again. Automatic Engine Shutdown If your vehicle is equipped with a keyless ignition, it has a feature that automatically shuts down the engine if it has been idling for an extended period. The ignition also turns off in order to save battery power. Before the engine shuts down, a message appears in the information display showing a timer counting down from 30 seconds. If you do not intervene within 30 seconds, the engine shuts down. Another message appears in the information display to inform you that the engine has shut down in order to save fuel. Start your vehicle as you normally do. Automatic Engine Shutdown Override Note: You cannot permanently switch off the automatic engine shutdown feature. When you switch it off temporarily, it turns on at the next ignition cycle.

1. Locate the key backup slot in center

console utility compartment.

2. With the buttons facing the rear of the vehicle and the key ring up, place the key into backup slot.

3. With the key in this position, press the

brake pedal, and then the button to switch on the engine.

Fast Restart The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. Within 20 seconds of switching the engine off, press the brake pedal and press the button. After 20 seconds have expired, you can no longer restart the engine without the key present inside your vehicle. Once the engine has started, it remains running until you press the button, even if the system does not detect a valid key. If you open and close a door while the engine is running, the system searches for a valid key. You cannot restart the engine if the system does not detect a valid key within 20 seconds. Failure to Start If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure:

146

Fusion/Mondeo (CC7)

E147165Starting and Stopping the Engine

Stopping the Engine When Your Vehicle is Moving

WARNING

Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not lock, but higher effort will be required. When the ignition is switched off, some electrical circuits, warning lamps and indicators may also be off.

Vehicles with an Ignition Key 1. Move the transmission selector lever to position N (automatic transmission) or neutral (manual transmission) and use the brakes to bring your vehicle to a safe stop.

2. When your vehicle has stopped, move the transmission selector lever to position P (automatic transmission) or 1 (manual transmission) and turn the key to position 0.

3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop.

2. When your vehicle has stopped, move

the transmission selector lever to position P.

3. Press and hold the button for one

second, or press it three times within two seconds.

4. Apply the parking brake.

You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: •

You can reset the timer by interacting with your vehicle (such as pressing the brake pedal or accelerator pedal). You can temporarily switch off the shutdown feature any time the ignition is on (for the current ignition cycle only). Use the information display to do so. See Information Displays (page 83).

•

• During the countdown before engine shutdown, you are prompted to press OK or RESET (depending on your type of information display) to temporarily switch the feature off (for the current ignition cycle only).

Stopping the Engine When Your Vehicle is Stationary Vehicles with an Ignition Key 1. Move the transmission selector lever to position P (automatic transmission) or 1 (manual transmission). 2. Turn the key to position 0. 3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever

to position P.

2. Press the button once. 3. Apply the parking brake. Note: This switches off the ignition, all electrical circuits, warning lamps and indicators. Note: If the engine is idling for 30 minutes, the ignition and engine automatically shut down.

147

Fusion/Mondeo (CC7)

Starting and Stopping the Engine

The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120 volt AC electrical source. We recommend that you do the following for a safe and correct operation: • Use a 16-gauge outdoor extension cord

that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA). This extension cord must be able to be used outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard.

• Use as short an extension cord as

possible.

• Do not use multiple extension cords. • Make sure that when in operation, the

extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire.

• Make sure your vehicle is parked in a

clean area, clear of combustibles.

• Make sure the heater, heater cord and extension cord are firmly connected.

• Check for heat anywhere in the

electrical hookup once the system has been operating for approximately 30
minutes.

• Make sure the heater system is

checked for proper operation before winter.

Guarding Against Exhaust Fumes

WARNING

If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and the leave the engine idling for long periods of time, we recommend that you do one of the following: • Open the windows at least 1 inch (2.5

centimeters) Set your climate control to outside air.

• ENGINE BLOCK HEATER (IF EQUIPPED)

WARNINGS

Failure to follow engine block heater instructions could result in property damage or serious personal injury. Do not use your heater with ungrounded electrical systems or two-pronged adapters. There is a risk

of electrical shock.

Note: The heater is most effective when outdoor temperatures are below 0°F (-18°C).

148

Fusion/Mondeo (CC7)

Starting and Stopping the Engine

Using the Engine Block Heater The engine block heater plug is located in a housing in the left fog lamp bezel. Open the hinged, circular door and make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.0 kilowatt-hours of energy per hour of use. The system does not have a thermostat. It will achieve maximum temperature after approximately three hours of operation. If you use the heater longer than three hours, this will not improve system performance and will use unnecessary electricity.

149

Fusion/Mondeo (CC7)

Unique Driving Characteristics

• •

• • •

•

•

•

•

•

•

Your foot is on the brake pedal. The transmission selector lever is in position D. The driver's door is closed. There is adequate brake vacuum. The interior compartment has been cooled or warmed to an acceptable level. The front windshield defroster and rear window defroster are off. The steering wheel is not turned rapidly or is not at a sharp angle. The vehicle is not on a steep road grade. The battery is within optimal operating conditions (battery state of charge and temperature in range). The engine coolant is at operating temperature. Elevation is below approximately 10000 feet (3048 m).

• Ambient temperature is moderate

(40°F–95°F) (4°C–35°C).

Note: The system allows multiple successive Auto StopStart events, but it may not operate in conditions of heavy traffic or in extended low speed operation. Note: The green Auto StartStop indicator light on the instrument cluster will illuminate to indicate

when the automatic engine stop occurs. Note:If the instrument cluster is equipped with a grey Auto StartStop indicator light, it is

illuminated when automatic engine stop is not available due to one of the above noted conditions. Automatic Engine Restart Any of the following conditions will result in an automatic restart of the engine:

START-STOP (IF EQUIPPED) The system helps reduce fuel consumption by automatically shutting off and restarting your vehicle’s engine while the vehicle is stopped. The engine will restart automatically when you release the brake pedal. In some situations, your vehicle may restart automatically, for example: • • Note: Power assist steering is turned off when the engine is off.

To maintain interior comfort To recharge the battery

WARNINGS The engine may restart automatically if required by the system. Switch the ignition off before opening the hood or performing any maintenance. Failure to do so may result in serious injuries due to automatic engine restart.

Always switch the ignition off before leaving your vehicle, as the system may have turned the engine off, but the ignition will still be on and automatic restart may occur.

The Auto StartStop system status is available at a glance within the information display. See Information Displays (page 83). Enabling Auto StartStop The system is automatically enabled every time you start your vehicle if the following conditions are met: •

The Auto StartStop button is not pressed (not illuminated). Your vehicle exceeds an initial speed of 3 mph (4 km/h) after the vehicle has been initially started. Your vehicle is stopped.

•

•

150

Fusion/Mondeo (CC7)

E146361Unique Driving Characteristics

Disabling Auto StartStop

Press the Auto StartStop button located on the center console to switch the system off. The button will illuminate. The system will only be deactivated for the current ignition cycle. Press the button again to restore Auto StartStop function. Note: If the Shift to P, Restart Engine message appears and the amber Auto StartStop indicator light is flashing, automatic restart is not available. The vehicle must be restarted manually. See Information Displays (page 83).

•

• •

•

•

• •

•

•

•

Your foot is removed from the brake pedal. You press the accelerator pedal. You press the accelerator and the brake pedal at the same time. The driver’s seat belt becomes unfastened or the driver’s door is ajar. The transmission selector lever is moved from position D. Your vehicle is moving. The interior compartment does not meet customer comfort when air conditioning or heat is on. Fogging of the windows could occur and the air conditioning is on. The battery is not within optimal operating conditions. The maximum engine off time is exceeded.

• When you press the Auto StartStop button while the engine is stopped automatically. Either the front or rear defroster is turned.

•

Any of the following conditions may result in an automatic restart of the engine: •

The blower fan speed is increased or the climate control temperature is changed.

• An electrical accessory is turned on or

plugged in.

151

Fusion/Mondeo (CC7)

PRNDSE146362Fuel and Refueling

SAFETY PRECAUTIONS

WARNINGS

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray

and fire.

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

Automotive fuels can cause serious injury or death if misused or mishandled. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is

pumped into an ungrounded fuel container.

Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

Observe the following guidelines when handling automotive fuel: •

Extinguish all smoking materials and any open flames before refueling your vehicle.

• Always turn off the vehicle before

refueling.

Fusion/Mondeo (CC7)

• Automotive fuels can be harmful or

fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

• Avoid getting fuel liquid in your eyes. If

fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin, clothing or both, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

•

•

152

Fuel and Refueling

Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage. REFUELING

WARNINGS

Fuel vapor burns violently and a fuel fire can cause severe injuries. Read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, flames and smoking materials away from fuel. Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is

against the law in some places.

Keep children away from the fuel pump; never let children pump fuel. Do not use personal electronic devices while refueling.

Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the

ground.

•

• Do not fill a fuel container while it is in the vehicle (including the cargo area). Keep the fuel pump nozzle in contact with the fuel container while filling. • Do not use a device that would hold

the fuel pump handle in the fill position.

FUEL QUALITY Note: Use of any fuel other than those recommended may cause vehicle damage, a loss of vehicle performance and repairs may not be covered under warranty. Choosing the Right Fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 15% ethanol. Do not use fuel ethanol (E85), diesel fuel, fuel-methanol, leaded fuel or any other fuel because it could damage or impair the emission control system. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. The use of leaded fuel is prohibited by law. Octane Recommendations 2.5L engine Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some fuel stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87
are not recommended. 1.6L and 2.0L EcoBoost® engines Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as "Regular" with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended. Premium fuel will provide improved performance and is recommended for severe duty usage such as trailer tow.

153

Fusion/Mondeo (CC7)

Fuel and Refueling

Easy Fuel™ Capless Fuel System

WARNING

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

When fueling your vehicle: 1. Put the vehicle in P (Park) and turn the

ignition off.

2. Open the fuel filler door.

3. Slowly insert the fuel filler nozzle fully

into the fuel system, and leave the nozzle fully inserted to open both doors until you are done pumping. Hold handle higher during insertion for easier access.

Fusion/Mondeo (CC7)

4. After you are done pumping fuel, slowly

remove the fuel filler nozzle—allow about five to ten seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle.

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuel filler nozzle. The overfilled fuel may run down the drain located below and in front of the fuel filler door. If the fuel fill inlet was not properly closed, a Check Fuel Fill Inlet message may appear on the instrument cluster. At the next opportunity, do the following: 1. Safely pull off the road. 2. Put the vehicle in P (Park) and turn the

ignition off.

3. Open the fuel filler door and remove

any visible debris from the fuel fill opening. Insert either the fuel fill nozzle or the fuel fill funnel provided with the vehicle several times to allow the inlet to close properly. This will dislodge any debris preventing the inlet from sealing.

4.

If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after four or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverse effect on powertrain components.

154

E156032E154765Fuel and Refueling

If you have run out of fuel: •

You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. With keyless ignition, just start the engine. Crank time will be longer than usual.

• Normally, adding 1 gallon (3.8 liters) of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gallon (3.8 liters) may be required. The service engine soon indicator may come on. For more information on the service engine soon indicator, See Warning Lamps and Indicators (page 79).

•

Refilling With a Portable Fuel Container

WARNINGS

Do not insert the nozzle of portable fuel containers or aftermarket funnels into the capless fuel system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, which could result in serious personal injury.

Do not try to pry open or push open the capless fuel system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others.

Note: Do not use aftermarket funnels; they will not work with the capless fuel system and can damage it. The included fuel funnel has been specially designed to work safely with your vehicle. When filling the vehicle’s fuel tank from a portable fuel container, use the funnel included with the vehicle.

155

Fusion/Mondeo (CC7)

E162864Fuel and Refueling

FUEL CONSUMPTION Note: The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty. Do not rely on this fuel for driving. The usable capacity of the fuel tank is the amount of fuel that can be put into the tank after the gauge indicates empty. The advertised capacity is the total fuel tank size – it is the combined usable capacity plus the empty reserve. Filling the Tank For consistent results when filling the fuel tank: •

Turn the ignition off before fueling; an inaccurate reading results if the engine is left running.

• Use the same fill rate

(low-medium-high) each time the tank is filled.

• Allow no more than two automatic

click-offs when filling.

Results are most accurate when the filling method is consistent. Calculating Fuel Economy Do not measure fuel economy during the first 1000 miles (1600 kilometers) of driving (this is your engine’s break-in period); a more accurate measurement is obtained after 2000 miles - 3000 miles (3200 kilometers - 4800 kilometers). Also, fuel expense, frequency of fill ups or fuel gauge readings are not accurate ways to measure fuel economy.

1. Locate the portable funnel that comes with your vehicle. The funnel is located behind the left-hand side rear seat, under the carpet. Fold down the left-hand side rear seat back. Pull back the piece of carpet to access the funnel.

2. Slowly insert the funnel into the

capless fuel system.

3. Fill the vehicle with fuel from the

portable fuel container.

4. When done, clean the funnel or

properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel.

156

Fusion/Mondeo (CC7)

E157279E157280Fuel and Refueling

Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your

vehicle is moving, especially at high speeds.

• Have the items listed in scheduled

maintenance information performed according to the specified schedule. The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system If other than Ford, Motorcraft® or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Illumination of the service engine soon indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly. An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately.

1. Fill the fuel tank completely and record

the initial odometer reading.

2. Each time you fill the tank, record the

amount of fuel added.

3. After at least three to five tank fill ups, fill the fuel tank and record the current odometer reading.

4. Subtract your initial odometer reading

from the current odometer reading. 5. Calculate fuel economy by dividing miles traveled by gallons used (For Metric: Multiply liters used by 100, then divide by kilometers traveled).

Keep a record for at least one month and record the type of driving (city or highway). This provides an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter show how temperature impacts fuel economy. In general, lower temperatures mean lower fuel economy. EMISSION CONTROL SYSTEM

WARNINGS

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the

engine compartment and exhaust system, which can start a fire.