2008 Ford Freestyle Owners Manual

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Conversation mirror (if equipped) The conversation mirror allows the driver to view the rear seating area.

This does not replace the rear view mirror.

Pull down on the housing to lock it in place. The rear view mirror may have to be adjusted to its lower arm position to prevent interference when the conversation mirror is extended down.

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: 1. Cupholders 2. Utility compartment with coin holder, a clamshell tray, audio input jack, USB port and power point 3. Rear power point, vent, rear heated seat controls (if quipped) and cupholder 4. Pen holder and CD holder

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

99

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Second row center console features (if equipped) The second row center console incorporates the following features: • Utility compartment • Cupholders • Flip forward armrest to provide a

flat load floor

Use only soft cups in the cupholder. Hard objects can

injure you in a collision.

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power points are located on the instrument panel and in the center console utility compartment. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used.

100

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

A third rear auxiliary power point is located on the rear of the center console which is accessible from the rear seat. A fourth auxiliary power point is located on the right trim panel in the rear cargo area.

Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty. POWER WINDOWS

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and pull the window switches to open and close windows. • Push down (to the first detent) • Pull up (to the first detent) and

and hold the switch to open.

hold the switch to close.

AUTO

Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviated by lowering a front window approximately two to three inches.

101

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

One touch up or down (Driver’s window only) This feature allows the driver’s window to open or close fully without holding the control down. To operate ONE TOUCH DOWN: • Press the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.

If the switch is pressed and held to the normal close or ONE TOUCH UP position during a ONE TOUCH DOWN event, the window will stop. If, after 1/2 second the switch is still held, the window will perform a normal close or ONE TOUCH UP. To operate ONE TOUCH UP: • Pull the switch completely up to the second detent and release quickly. The window will close fully. Momentarily press the switch to any position to stop the window operation.

If the switch is pressed and held to the normal open or ONE TOUCH DOWN position during a ONE TOUCH UP event, the window will stop. If, after 1/2 second the switch is still held, the window will perform a normal open or ONE TOUCH DOWN.

Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls (except for the driver’s) press the right side of the control. Press the left side to restore the window controls.

102

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Bounce-Back (Driver’s window only) When an obstacle has been detected in the window opening as the window is moving upward, the window will automatically reverse direction and move down. This is known as “bounce-back”. If the ignition is turned OFF (without accessory delay being active) during bounce-back, the window will move down until the bounce back position is reached.

Security Override If during a bounce-back condition, the switch is released to the neutral position, then held in the one touch up position within two seconds after the window reaches the bounce-back position, the window will travel up with no bounce-back protection. If the switch is released before the window reaches fully closed or the ignition is turned OFF (without accessory delay being active), the window will stop. Security override can be used if the window movement is restricted in some way, for example, if there is ice on the window or seals.

Accessory delay With accessory delay, the radio, Family Entertainment DVD System (if equipped), power windows, and moonroof (if equipped) operate for up to ten minutes after the ignition switch is turned from the ON to the OFF position or until one of the front doors are opened.

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror UP or DOWN and from SIDE to SIDE.

Do not adjust the mirror while the vehicle is in motion.

Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equipped with an interior rear view mirror that has an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare.

103

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Without voice activated Navigation System or SYNC™

With voice activated Navigation System or SYNC™

The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

EXTERIOR MIRRORS

Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

104

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control (located on the instrument panel) to adjust accelerator and brake pedal. • Press the top of the control to • Press the bottom of the control to adjust the pedals towards you. The adjustment allows for approximately 2.8 inches (71 mm) of maximum travel.

adjust the pedals away from you.

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

105

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Memory feature (if equipped) The accelerator and brake pedal positions are saved when doing a memory set function and can be recalled along with the vehicle personality features when a memory position is selected through the remote entry transmitter, keyless entry keypad or memory switch on the driver’s door (if equipped with memory feature). Refer to Memory seats/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter. SPEED CONTROL With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator instrument cluster will turn on.

light on the

OFF

ON

CNCL

RSM

SET

SET

OFF

ON

CNCL

RSM

SET

SET

Note: • Vehicle speed may vary momentarily when driving up and down a

steep hill.

106

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

Disengaging speed control To disengage the speed control: • Depress the brake pedal or press CNCL (Cancel). Disengaging the speed control will not erase previous set speed. Resuming a set speed Press the RES control and release it. This will automatically return the vehicle to the previously set speed.

OFF

ON

CNCL

RSM

SET

SET

OFF

ON

CNCL

RSM

SET

SET

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

107

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

OFF

ON

CNCL

RSM

SET

SET

OFF

ON

CNCL

RSM

SET

SET

OFF

ON

CNCL

RSM

SET

SET

Driver Controls

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1
mph (1.6 km/h). • Depress the brake pedal or press CNCL (Cancel) until the desired vehicle speed is reached, press the SET + control.

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or press CNCL (Cancel). This will not erase your vehicle’s previously set speed.

• Press the speed control OFF

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

108

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

STEERING WHEEL CONTROLS (IF EQUIPPED)

Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use steering wheel controls and other devices not essential to the driving task when it is safe to do so.

Radio control features Press MEDIA to select: • AM, FM1, FM2
• SAT1, SAT2 or SAT3 (Satellite • CD

Radio mode if equipped).

In AM, FM1, or FM2 mode: • Press SEEK to access the

next/previous strong station.

In Satellite radio mode (if equipped): • Press and release SEEK to access the next/previous strong station. • Press and hold SEEK to fast

advance through preset channels or subscribed channels.

VOL

SEEK

MEDIA

MUTE

VOL

SEEK

MEDIA

MUTE

In CD mode: • Press SEEK to listen to the next track on the disc.

109

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

In any mode: • Press VOL up or down to adjust • Press MUTE to mute the volume.

the volume.

icon appears on the

Navigation system Push To Talk (PTT) hands free control feature (if equipped) Press and hold PTT briefly until the voice Navigation display to use the voice command feature. Press PTT again to end a voice command. For further information on the Navigation system, refer to the Navigation supplement. SYNC™ system hands free control feature (if equipped) Press and hold VOICE briefly until icon appears on the the voice display to use the voice command feature. Press and hold text message. Press OK to confirm your selection. For further information on the SYNC™ system, refer to the SYNC™ supplement.

to send a call or

110

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

icon appears on the

Navigation/SYNC™ hands free control feature (if equipped) Press and hold VOICE briefly until the voice Navigation display to use the voice command feature. Press SEND or END to complete a voice command. For further information on the Navigation system/SYNC™ system, refer to the Navigation and SYNC™ supplements. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle.

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

The moon roof is equipped with an automatic, one-touch, express opening and closing feature. To stop motion at any time during the one-touch operation, press the control a second time. To open the moon roof: To open the moon roof, press the rear portion of the control (to the first detent). To activate the automatic, one-touch, express open feature, press the rear portion of the control (to the second detent) and release quickly.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

To close the moon roof: To close, press the front portion of the control (to the first detent). To activate the automatic, one-touch, express close feature, press the front portion of the control (to the second detent) and release quickly.

111

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Bounce back: When an obstacle has been detected in the moon roof opening as the moon roof is closing, the moon roof will automatically open and stop at a prescribed position. Bounce back override: To override bounce back, press and hold the front portion of the control. For example: Bounce back can be used to overcome the resistance of ice on the moon roof or seals. To vent: To tilt the moon roof into the vent position (when the glass panel is closed), press and hold the front portion of the control. To close the moon roof from the vent position, press and hold the rear portion of the control until the glass panel stops moving. The moon roof has a sliding shade that can be opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515.

112

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons. Note: Some entry gates and garage door openers may require you to replace Step 2 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 3. Firmly press, hold for five seconds and release the programmed HomeLink威 button up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink威 button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink威 button is pressed and released. • If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit).

113

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 1 in the “Programming” section. For questions or comments, please contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined in the “Programming” section, replace Step 2 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 2 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 3 in the “Programming” section.

114

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 1 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 1 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

115

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MESSAGE CENTER With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.

Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer • Trip Odometer • Distance to Empty • Average Fuel Economy • Trip Elapsed Drive Time • Compass Display • Compass Zone Adjustment • Compass Calibration Adjustment Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel.

116

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The DTE function will display FUEL LEVEL LOW and a single tone when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10
minutes. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing 100 miles traveled by gallons of fuel used (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. For more information refer to Fuel Information in the Maintenance and Specifications chapter. Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer.

service stations

117

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

2. Press and release RESET to pause the timer. 3. Press and hold RESET for 2 seconds in order to reset the timer. Compass display The compass heading is displayed in the lower left corner of the message center next to the odometer. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Compass zone adjustment Perform the following steps on an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater / air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Turn ignition to the ON position. 2. Start the engine. 3. Determine your magnetic zone by referring to the zone map.

23

15

14
13
12

7 8 9 1011

118

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

4. Press the SETUP control repeatedly until the message center says “RESET FOR ZONE SETTING”. 5. Press the RESET control to enter Zone Setting mode. 6. Press RESET repeatedly until the desired zone setting is displayed. The message center will automatically exit zone setting mode if enough time passes without pressing a button. Compass calibration adjustment Perform the following steps on an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater / air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Turn ignition to the ON position. 2. Start the engine. 3. Press the SETUP button repeatedly until the message center displays “RESET FOR CALIBRATION”.

4. Press RESET to enter compass calibration mode which will display “CIRCLE SLOWLY TO CALIBRATE”.

5. Drive the vehicle in circles up to three times until the message ⬙CALIBRATION COMPLETED⬙ appears and one of the 8 valid headings (N, NE, E, SE, S, SW, W, NW) is displayed. 6. Verify that the calibration process has taken place by driving the vehicle in at least one circle, confirming that the heading changes accordingly. If this happens, the compass has been calibrated successfully. Otherwise, if the display shows only one heading as the vehicle is being driven around, repeat the procedure from Step 3.

119

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Setup menu Press this control for the following displays: • System Check • Oil Life • Language • Units (English/Metric) • Autolamp Delay (if equipped) • Autolock (if equipped) • Autounlock (if equipped) • Power Liftgate (if equipped) • Easy entry/exit seat (if equipped) System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for two to four seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report is as follows: 1. OIL LIFE 2. CHARGING SYSTEM 3. WASHER FLUID LEVEL 4. DOORS CLOSED 5. LIFTGATE CLOSED 6. BRAKE SYSTEM 7. TIRE PRESSURE MONITORING SYSTEM 8. DISTANCE TO EMPTY Oil life An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS.

120

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To reset the oil monitoring system to 100% after each oil change [approximately 7,500 miles (12,000 km) or 6 months] perform the following: 1. Press the SETUP control to enter SYSTEM CHECK, then press SETUP control again to display “OIL LIFE = XXX% HOLD RESET = NEW”.

2. Press and hold the RESET control for 2 seconds and release. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed. 3. While “OIL LIFE SET TO 100%” is displayed, if a lower oil life is desired, press and release the RESET control to reduce the value. Each press of the RESET control reduces the value by 10 percent. Note: Oil life of 100% equals 7,500 miles (12,000 km) or 6 months. For example, setting oil life to 60% sets the oil life value to 4,500 miles (7,200 km) and 108 days. Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Autolamp delay (if equipped) This feature keeps your headlights on for up to three minutes after the ignition is switched off.

121

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds. Autolock (if equipped) This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolock ON or OFF. Autounlock (if equipped) This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off. 1. To disable/enable the autounlock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control switch to turn the autounlock ON or OFF. Power Liftgate (if equipped) This feature allows users to open/close the rear liftgate at the touch of a button. 1. To disable/enable the power liftgate feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the power liftgate ON or OFF. If disabled, the outside release handle and the rear cargo area control button are off. The instrument panel button will continue to function the liftgate in power mode.

122

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Easy entry/exit seat (if equipped) This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy entry/exit seat feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the easy entry/exit seat ON or OFF. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for several seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into three categories: • They will not disappear until a condition is changed. • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

This acts as a reminder that these warning conditions still exist within the vehicle.

Warnings

Driver door ajar Passenger door ajar Rear Left door ajar Rear Right door ajar Fuel level low Check charging system Check brake system

Status

Warning cannot be reset (CLOSE DOOR TO RESET) will be displayed

Warning returns after 10 minutes

123

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Status

Warning returns after the ignition key is turned from OFF to RUN

Warnings Brake fluid level low Park brake engaged Low tire pressure Tire pressure monitor fault Tire pressure sensor fault Liftgate ajar Washer fluid level low Change oil soon Oil change required DRIVER DOOR AJAR. Displayed when the driver’s door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger side door is not completely closed. REAR LEFT DOOR AJAR. Displayed when the left rear door is not completely closed. REAR RIGHT DOOR AJAR. Displayed when the right rear door is not completely closed. FUEL LEVEL LOW. Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. CHECK BRAKE SYSTEM. Displayed when the brake system needs servicing. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW BRAKE FLUID. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. PARK BRAKE ENGAGED. Displayed when the park brake is engaged. If the warning stays on after the park brake is off, contact your authorized dealer as soon as possible. LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter.

124

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

TIRE PRESSURE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. LIFTGATE AJAR. Displayed when the liftgate is not completely closed. WASHER FLUID LEVEL LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. OIL CHANGE REQUIRED/CHANGE OIL SOON. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed.

POWER LIFTGATE (PLG) (IF EQUIPPED) You can power open or close the liftgate with the following controls. • instrument panel control button • integrated keyhead transmitter button • outside liftgate control button • control button in the rear cargo area Opening and Closing the power liftgate:

WARNING: Make sure all persons are clear of the power liftgate area before using the power liftgate control.

Keep keys out of reach of children. Do not allow children to play near an open or moving power liftgate.

The liftgate will only operate with the vehicle in P (Park). When the liftgate is being power closed, a chime will sound three times as the liftgate begins to power close. A single chime indicates a problem with the close request, caused by:

125

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls • the ignition is in Run and the transmission is not in Park • or the Battery Voltage is below the minimum operating voltage • or the vehicle speed is at or above 3 mph (5 kph) A fast continuous chime during power closing indicates there is an excessive load on the liftgate (snow, bike rack, etc.) or a possible strut malfunction. If any excessive load is removed and you still have a faster chime, have the system serviced immediately by your authorized dealer. Do not attempt to manually force the liftgate to travel faster than the power system will permit. This will activate the obstacle detection feature. Exercise care, when power opening or closing the liftgate in a garage or other enclosed area with a low ceiling or close to a wall/garage door. The liftgate could be damaged from the contact. Disable the power feature and operate the liftgate manually if necessary. When power operating the liftgate at temperatures below 32° F (0° C), the liftgate may stop about 5 inches (12.7 cm) from the full open position. The liftgate can be fully opened by pushing it upward to the maximum open position. The Power Liftgate feature can be enabled or disabled using the Message Center. With the control in the OFF position, power operation is disabled from the liftgate handle button and from the rear cargo area button. The integrated keyhead transmitter and instrument panel switch will operate the liftgate regardless of the position state of the Message Center. Refer to the Message Center section in this chapter. To power open or close the liftgate from the Instrument panel: Press the button, located to the left of the steering column, once to power open or close the liftgate.

126

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To power open or close the liftgate with the integrated keyhead transmitter: Press power open or close the liftgate. Refer to Remote Entry System in the Locks and security chapter.

twice within 3 seconds to

To power close the liftgate with the rear cargo area control button: Press and release the control on the left rear quarter panel to close the liftgate. Note: The rear cargo area control button is disabled when the liftgate is latched.

Warning, keep clear of the liftgate when activating the rear switch.

Note: The liftgate movement direction can be reversed with a second press of the instrument panel, or the rear cargo area control button, or a second double press of the integrated keyhead transmitter button. To power open the liftgate with outside liftgate control button: 1. To open, unlock the liftgate with the integrated keyhead transmitter or power door unlock control. 2. Push the control button located above the liftgate outside handle to unlatch and power open the liftgate.

127

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: For the best performance allow the power system to open the liftgate after pushing the control. Manually pushing or pulling the liftgate may activate the system’s obstacle detection feature and stop the power system. To manually operate the liftgate: 1. Disable the liftgate power function. Refer to the Message Center in this chapter. 2. Open and close the liftgate as you would a standard liftgate. Refer to the Manual liftgate in this chapter. Note: In case of operation in extreme cold -40° F (-40° C), or on extreme inclines, manual operation of the liftgate is suggested. Obstacle detection The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system will reverse to full open when it detects an obstacle. A chime will sound 3 times when an obstacle is detected as the liftgate begins to reopen. Once the obstacle is removed, the liftgate can be closed under power. If the power liftgate is opening, the system will stop and a chime will sound 3 times when an obstacle is detected. Once the obstacle is removed, the liftgate can again be operated normally. Resetting the power liftgate: The power liftgate may not operate properly and may need to be reset if any of these conditions occur: • a low voltage or dead battery or disconnected battery • the liftgate has been left open or unlatched for more than six (6)

hours

To reset the power liftgate: 1. Ensure the battery is properly connected and charged. 2. Manually close and fully latch the liftgate. 3. Power open the liftgate by using the integrated keyhead transmitter, or the instrument panel control button. The outside liftgate control button can also be used if the power liftgate is enabled in the Message Center. Note: If the battery is disconnected, discharged, or a new battery is installed, the power liftgate needs to be power opened to the full open position to reset the power liftgate positions.

128

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MANUAL LIFTGATE To open the liftgate, unlock the liftgate (with the power door locks or the remote entry transmitter button) and push the outside liftgate control button. • Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is opened, the liftgate could be damaged against a low ceiling.

• Do not leave the liftgate open while driving. Doing so could cause

serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.

Make sure that the liftgate door is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent

passengers and cargo from falling out. If you must drive with the liftgate door open, keep the vents open so outside air comes into the vehicle.

CARGO AREA FEATURES

Cargo net (if equipped) The cargo pouch net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50
lbs. (22 kg) in the net.

The cargo net is not designed to restrain objects

during a collision or heavy braking.

Cargo van storage compartment (if equipped) The cargo van storage compartment consists of two storage compartments located in the floor of the cargo area.

129

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. To open, unlock and turn the handle to lift the cover. 2. To close, lower the cover and turn the handle to lock.

LUGGAGE RACK Maximum load is 125 lbs (57 kg) on the roof rack structure, or 100 lbs (45 kg) on the roof panel, evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. Cross-bars/tie down loops (if equipped) can be adjusted to fit the item(s) being carried.

130

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS Your vehicle is equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter. Vehicles with a power liftgate will have a four-button IKT while vehicles without a power liftgate will have a three-button IKT.

Your IKTs are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied IKTs, replacement IKTs are available through your authorized dealer. Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. Always carry a spare key with you in case of an emergency. For more information regarding programming replacement IKTs, refer to the SecuriLock™ passive anti-theft system section later in this chapter. Note: Your vehicle’s IKTs were issued with an adhesive security tag on them that provides important vehicle key cut information. It is recommended that you maintain the tag in a safe place for future reference.

Recommended handling of the Integrated Keyhead Transmitter (IKT) To avoid inadvertently activating the remote entry functions of your vehicle, it is recommended that the Integrated Keyhead Transmitter (IKT) be handled properly when starting and turning off your vehicle.

131

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

When inserting the IKT into the ignition cylinder, place your thumb on the center thumb rest of the IKT and forefinger on the logo badge on the opposite side.

To gain more leverage when rotating the IKT in the ignition lock cylinder, you can readjust the location of your thumb to grasp the IKT on the control. outer edge next to the

Likewise, when rotating the IKT to the 1 (LOCK) position in the ignition lock cylinder, the bottom edge of the IKT adjacent to the control can be utilized.

control to unlock all

POWER DOOR LOCKS • Press the • Press the

doors.

control to lock all

doors.

132

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Smart locks This feature helps to prevent you from locking yourself out of the vehicle if your key is still in the ignition. When you open one of the front doors or the liftgate and you lock the vehicle with the power door lock control (on the driver or passenger door trim panel), all the doors will lock, then all doors will automatically unlock reminding you that your key is still in the ignition. The vehicle can still be locked, with the key in the ignition, by locking the driver’s door with a key, using the lock control on the remote entry transmitter portion of your Integrated Keyhead Transmitter, or locking the vehicle with the keyless entry keypad. If both front doors and the liftgate are closed, the vehicle can be locked from any method, regardless of whether the key is in the ignition or not.

Autolock feature The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the 3 (RUN) position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h) for greater

than 2 seconds.

The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (RUN) • the vehicle then attains a speed greater than 12 mph (20 km/h) for

position and the vehicle speed is 9 mph (15 km/h) or lower, and

greater than 2 seconds.

Deactivating/activating autolock feature Your vehicle comes with the autolock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock procedure, • using a keypad procedure, or • or by using the instrument cluster message center. Refer to Message

center in the Driver Controls chapter.

Note: The autolock feature can be activated/deactivated independently of the autounlock feature.

133

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the 1 (LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry key pad autolock enable/disable procedure 1. Turn the ignition to the 1 (LOCK) position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.

134

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Autounlock feature The autounlock feature will unlock all the doors when: • the ignition is in the 3 (RUN) position, all the doors are closed, and

the vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the 1
• the driver door is opened within 10 minutes of the ignition being

(LOCK) or 2 (ACC) position; and

transitioned to the 1 (LOCK) or 2 (ACC) position.

Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock feature Your vehicle comes with the autounlock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock sequence, • using a keypad procedure, or • or by using the instrument cluster message center. Refer to Message

center in the Driver Controls chapter.

Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active.

135

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition to the 1 (LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry key pad autounlock enable/disable procedure 1. Turn the ignition to the 1 (LOCK) position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second time. 5. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. CHILDPROOF DOOR LOCKS • Move control up to engage the • Move control down to disengage

childproof lock.

childproof lock.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors.

136

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• When the childproof door locks are set, the rear doors cannot be • The rear doors can be opened from the outside when the power door

opened from the inside.

locks are unlocked.

REMOTE ENTRY SYSTEM The Integrated Keyhead Transmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. There are 2 possible types of IKTs: • Vehicles equipped with a power

liftgate

137

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security • Vehicles not equipped with a

power liftgate

The typical operating range for your IKT is approximately 33 feet (10
meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the power liftgate (if equipped). • activate the personal alarm. • arm and disarm the perimeter anti-theft system. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the 4 (START) position. The panic feature operates with the key in the 1 (LOCK) position. If there are problems with the remote entry system, make sure to take ALL Integrated Keyhead Transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors/two stage unlock 1. Press lamps will illuminate.

and release to unlock the driver’s door. Note: The interior

138

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

and release again within three seconds to unlock all the

2. Press doors. The remote entry system activates the illuminated entry feature; this feature turns on the lamps for 25 seconds or until the ignition is turned to the 3 (RUN) position. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver feature will turn off the interior lamps 10 minutes after the ignition is turned to the 1 (LOCK) position. Two stage unlocking may be disabled or re-enabled by simultaneously pressing the controls on the IKT for four seconds (disabling two stage unlock allows all vehicle doors to unlock simultaneously). The turn lamps will flash twice to indicate that two-stage unlock was enabled or disabled.

and

and release to lock all the doors. The turn lamps will flash. and release again within three seconds to confirm that all

Locking the doors 1. Press 2. Press the doors are closed. Note: The doors will lock again, the horn will chirp and the turn lamps will flash once if all the doors and liftgate are closed. Note: If any door or the liftgate is not closed, the horn will chirp twice and the lamps will not flash.

Car finder Press will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.

twice within 3 seconds. The horn will chirp and the turn lamps

for 1.5 seconds to activate the alarm. The horn will

Sounding a panic alarm Press and hold sound and the turn lamps will flash for a maximum of 3 minutes. The alarm can be deactivated with a short press and release of turning the ignition to RUN, or by allowing the alarm to time out after 3
minutes. Note: The panic alarm will only operate when the ignition is in the 1
(LOCK) position.

, by

139

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Opening the power liftgate (if equipped) Press

twice within 3 seconds to fully unlatch and open the liftgate.

Make sure all persons are clear of the liftgate area before using power liftgate control.

In order to fully lower and latch the liftgate, press the control twice. If the liftgate stops mid travel, it may have detected an obstacle, Check to ensure the liftgate swing zone is free from obstruction and reset the power assist by manually closing the liftgate. Normal operation can then be resumed.

Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers

and cargo from falling out. If you must drive with the liftgate open, keep the vents open so outside air comes into the vehicle.

Memory seats/power mirrors/adjustable pedals (if equipped) The Integrated Keyhead Transmitter allows you to recall the memory seat/mirror feature. to automatically move the seat, mirror and adjustable pedals (if Press equipped) to the desired memory position. Note: The seat will not travel to its final position if the key is not in the ignition and the easy entry feature is enabled. Activating the memory feature To activate this feature: 1. Position the seat, mirrors, and adjustable pedals (if equipped) to the desired positions.

140

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press the lock or unlock control on the Integrated keyhead Transmitter and then press the 1 or 2 control on the driver’s door panel which you would like to associate with the seat and Driver 1 or Driver 2 positions. 4. Repeat this procedure for another Integrated Keyhead Transmitter if desired. Deactivating the memory feature To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2. Within five seconds, press the lock or unlock control on the Integrated Keyhead Transmitter which you would like to deactivate and then press the SET control on the driver’s door panel again. 3. Repeat this procedure for another Integrated Keyhead Transmitter if desired.

Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover.

141

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the instructions inside the IKT for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the battery cover back onto the key. Note: Replacement of the battery will not cause the IKT to become deprogrammed from your vehicle. The IKT should operate normally after battery replacement.

Replacing lost Integrated Keyhead Transmitters (IKTs) If you would like to have your Integrated Keyhead Transmitters reprogrammed because you lost one, or would like to buy additional IKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to reprogram your Integrated Keyhead Transmitters (IKTs) To program a new Integrated Keyhead Transmitter yourself, refer to Programming spare keys in the SecuriLock™ passive anti-theft section of this chapter. Note: At least two IKTs are required to perform this procedure yourself.

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead Transmitter or the keyless entry system keypad is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, or • the Integrated Keyhead Transmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad, or 142

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

(unlock) control on the transmitter is pressed:

• after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Perimeter lamps illuminated entry With the Integrated Keyhead Transmitter system, the following items will illuminate when the • Headlamps • Park lamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the Integrated Keyhead Transmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad, or • after 25 seconds of illumination. Note: On some vehicles, the perimeter lamps illuminated entry feature will not activate in daylight conditions. Deactivating/activating perimeter lamps illuminated entry You may enable/disable this feature by having your vehicle serviced by your authorized dealer. You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3
(RUN) position to the 1 (LOCK) position.

143

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. Press the power door unlock control twice within 5 seconds. Note: The horn will chirp once to indicate the perimeter lighting feature has been deactivated. The horn will chirp once and honk once (one short and one long) to indicate the perimeter lighting feature has been activated. 7. Turn the ignition to the 1 (LOCK) position to exit the procedure. Note: The horn will chirp once to confirm the procedure is complete.

Illuminated exit • When all vehicle doors are closed and the key is removed from the ignition, the interior dome lamps (and the exterior mirror puddle lamps, if equipped) will illuminate.

The lights will turn off if all the doors remain closed and • 25 seconds elapse, or • the key is inserted in the ignition. Battery saver The battery saver will shut off the interior lamps 10 minutes after the ignition has been turned to the 1 (LOCK) position. • If the dome lamps were turned on using the panel dimmer control, the battery saver will shut them off 10 minutes after the ignition has been turned to the 1 (LOCK) position. • If the courtesy lamps were turned on because one of the vehicle doors or the liftgate was opened, the battery saver will shut off them off 10
minutes after the ignition has been turned to the 1 (LOCK) position.

• The battery saver will shut off the headlamps 10 minutes after the

ignition has been turned to the 1 (LOCK) position.

144

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYLESS ENTRY SYSTEM You can use the keyless entry keypad to: • lock or unlock the doors without • recall memory seat, power

using a key.

mirrors, and adjustable pedals (if equipped).

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box and is available from your authorized dealer. You can also create up to three of your own 5–digit personal entry codes. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code and keypad association to memory seats, mirrors, and adjustable pedals (if equipped) To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. To associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 settings. • Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting. Note: The factory-set code cannot be associated with a memory setting.

5. The doors will lock then unlock to confirm that your personal keycode has been programmed to the module.

145

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal

code.

Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. All personal codes are now erased and only the factory set 5–digit code will work.

control on the remote entry transmitter

Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the UNLOCK portion of your Integrated Keyhead Transmitter. • the ignition is turned to the 3 (RUN) position. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate. Note: If the two-stage unlocking feature is disabled, all doors will unlock; for more information regarding two-stage unlocking, refer to the Two stage unlocking section earlier in this chapter. To unlock all doors, enter the factory set code or your personal code, then press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time (with the driver’s door closed). You do not need to enter the keypad code first.

146

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded Integrated Keyhead Transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded Integrated Keyhead Transmitters; additional coded IKTs may be purchased from your authorized dealer. Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. The authorized dealer can program your spare IKTs to your vehicle or you can program the IKTs yourself. Refer to Programming spare Integrated Keyhead Transmitters for instructions on how to program the coded key. Note: The SecuriLock™ passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded IKT while starting the engine. These objects will not cause damage to the coded IKT, but may cause a momentary issue if they are too close to the IKT when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded IKT and restart the engine.

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the 1
(LOCK) position, the indicator will flash once every 2 seconds to indicate the SecuriLock™ system is functioning as a theft deterrent.

• When the ignition is in the 3 (RUN) position, the indicator will glow

for 3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock™ system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. If this occurs, the vehicle will not start and should be taken to an authorized dealer for service.

147

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Automatic arming The vehicle is armed immediately after switching the ignition to the 1
(LOCK) position. The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed.

Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the 3
(RUN) position. The theft indicator will illuminate for three seconds and then go out. If the theft indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your authorized dealer.

Replacement Integrated Keyless Transmitters (IKT) and coded keys Note: Your vehicle comes equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote keyless entry transmitter. A maximum of eight coded keys can be programmed to your vehicle; only four of these eight keys can be IKTs with remote entry functionality. If your IKTs or standard SecuriLock™ coded keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys You can program your own Integrated Keyhead Transmitters or standard SecuriLock™ coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry transmitter portion of the IKT to your vehicle. Note: A maximum of eight coded keys can be programmed to your vehicle; only four of these eight can be IKTs with remote entry functionality.

148

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

SecuriLock™ keys.

Tips: • Only use Integrated Keyhead Transmitters (IKTs) or standard • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

• If two previously programmed coded keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.

Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition.

2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds. 3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition. 4. Within ten seconds of turning the ignition to the 1 (LOCK) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds. 6. Turn the ignition to the 1 (LOCK) position and remove the second previously programmed coded key from the ignition. 7. Within twenty seconds of turning the ignition to the 1 (LOCK) position and removing the previously programmed coded key, insert the new unprogrammed key (new key/valet key) into the ignition. 8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least six seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and will operate the remote entry system (if the new key is an Integrated Keyhead Transmitter). The theft indicator light will illuminate for three seconds and then go out to indicate successful programming.

149

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

If the key was not successfully programmed, it will not start your vehicle’s engine and/or will not operate the remote entry features. The theft indicator light may flash on and off. Wait 20 seconds and you may repeat Steps 1 through 8. If failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), wait twenty seconds and then repeat this procedure from Step 1.

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help protect your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL Integrated Keyhead Transmitters are brought to the authorized dealer to aid in troubleshooting.

Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the turn signal lamps and will sound the horn. The system is ready to arm whenever the key is in the 1(LOCK) position, or is removed from the ignition. Either of the following actions will prearm the alarm system: • Press the

control on the remote entry transmitter portion of your

Integrated Keyhead Transmitter. When you press the lock control twice within three seconds on the remote entry transmitter portion of your IKT, the horn will chirp once to let you know that all doors, the hood and the liftgate are closed. If any of these are not closed, the horn will chirp twice to warn you that a door, the hood or the liftgate is still open.

• Press the driver or passenger interior door lock control while the door is open, then close the door.

150

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• Press the 7 • 8 and 9 • 0

controls on the keyless entry pad at the same time to lock the doors (driver’s door must be closed).

There is a 20 second countdown when any of the above actions occur before the vehicle becomes armed. Each door, the hood, and the liftgate is armed individually, and if any are open, they must be closed before the open entry point (door, hood, or liftgate) can enter the 20
second countdown. The turn signal lamps will flash once when all doors, the hood and the liftgate are closed indicating the vehicle is locked and entering the 20 second countdown.

your Integrated Keyhead Transmitter.

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion of • Unlock the doors by using your keyless entry pad. • Unlock the driver’s door with a key. Turn the key full rearward (toward the rear of the vehicle) to ensure the alarm disarms. • Turn ignition to the 3 (ON) position with a valid SecuriLock™ key or • Press the panic control on the remote entry transmitter portion of your IKT. This will only shut off the horn and turn lamps when the alarm is sounding. The alarm system will still be armed.

Integrated Keyhead Transmitter (IKT).

Pressing the power door UNLOCK control within the 20 second prearmed mode will return the vehicle to a disarmed state. Triggering the anti-theft system The armed system will be triggered if: • Any door, the hood or the liftgate is opened without using the door • The ignition is turned to the 3 (ON) position with an invalid

key, keypad or the remote entry transmitter portion of your IKT.

SecuriLock™ key or IKT.

151

2008 Taurus X (219) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

SEATING Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Before returning the seatback to its original position, make sure