Download PDF Manual

Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available.


Used engine coolant should be disposed of in an appropriate


manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.


coolant concentration above 50%.


Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the • A coolant concentration of 60% will provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.


If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease the • A coolant concentration of 40% will provide improved overheat


coolant concentration to 40%.


protection. Engine coolant concentrations below 40% will decrease the corrosion and freeze protection characteristics of the engine coolant and may cause engine damage.


Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


240


Maintenance


Powertrain Limiting and Protection Note: Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible. The engine control module (ECU) is equipped with a feature called powertrain limiting and protection (PTLP). PTLP will help protect the engine from damage in case the engine is overheating (coolant and/or oil temperature too hot). PTLP will automatically intervene during normal engine operation should it determine the engine coolant and/or oil temperatures are too hot. It does this by gradually reducing the maximum allowable engine rpm until the engine has cooled sufficiently. PTLP will automatically reinstate normal engine operation if it determines the engine temperatures have cooled sufficiently. During an engine overheating condition, the instrument cluster will display a message and a chime will sound. The engine may also have temporarily reduced power and reduced rpm limit during an overheating condition. Operating the engine with high engine coolant temperature (coolant gauge indicator is red) may cause powertrain damage. Stop the vehicle as soon as safely possible and let the engine cool off while idling.


TRANSMISSION FLUID CHECK


Checking Automatic Transmission Fluid Note: Transmission fluid should be checked and, if required, added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. See your Scheduled Maintenance Information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e., if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


241


Checking and Adding Manual Transmission Fluid (If Equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Technical Specifications section in the Capacities and Specifications chapter.


BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately.


POWER STEERING FLUID CHECK Your vehicle is equipped with an electric power steering (EPS) system. There is no fluid reservoir to check or fill. For additional information on the electric power steering (EPS) system, Refer to Driving Aids.


FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed.


WASHER FLUID CHECK


WARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure


to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.


Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See the technical specifications chart in the Capacities and Specifications chapter. Note: The front and rear washer systems are supplied from the same reservoir.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


242


Maintenance


State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.


CHANGING THE VEHICLE BATTERY


WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.


WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.


WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.


Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.


WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.


Your vehicle is equipped with a Motorcraft® maintenance-free battery which normally does not require additional water during its life of service. Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


243


If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. To ensure proper operation of the battery management system (BMS), any electrical devices that are added to the vehicle should not have their ground connection made directly at the negative battery post. A connection at the negative battery post can cause inaccurate measurements of the battery condition and potential incorrect system operation. Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability and may also affect the performance of other electrical systems in the vehicle. When a battery replacement is required, the battery should only be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle. When the battery is disconnected or a new battery installed, the automatic transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly when first driven. This operation is considered normal and will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


244


Maintenance


CHECKING THE WIPER BLADES


Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth.


CHANGING THE WIPER BLADES The wiper arms can be manually moved when the ignition is off. This allows for ease of blade replacement and cleaning under the blades. 1. Turn the ignition off before removing the wiper blade. 2. Pull the wiper blade and arm away from the glass. 3. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it.


4. Attach the new blade to the arm and snap it into place. Lower the wiper arm and blade back to the windshield. The wiper arms will automatically return to their normal position when the ignition is turned on. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. Refer to the Vehicle Care chapter. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


245


Changing the Rear Window Wiper Blade


1. Lift the wiper arm. 2. Slightly rotate the wiper blade from the wiper arm. 3. Disengage the wiper blade from the wiper arm. 4. Remove the wiper blade. 5. Install in the reverse order.


Note: Make sure that the wiper blade locks into place. Be careful that the wiper arm does not spring back against the glass when the blade is not in place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield.


AIR FILTER CHECK


WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner


removed and do not remove it while the engine is running.


When changing the air filter element, use only the air filter element listed. Refer to Motorcraft® Part Numbers in the Capacities and Specifications chapter. For EcoBoost equipped vehicles: When servicing the air cleaner, it is important that no foreign material enter the air induction system. The engine and turbocharger are susceptible to damage from even small particles. Refer to Scheduled Maintenance for the appropriate intervals for changing the air filter element. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


246


Maintenance


Changing the Air Filter Element


1. Loosen the screws that secure the air filter housing cover (A). 2. Carefully lift the air filter housing cover. 3. Remove the air filter element (B) from the air filter housing (C). 4. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 5. Install a new air filter element. Slide the open end of the air filter element in first, below the tab.


6. Align the tab on the closed end of the air filter element (B) with the slot in the air filter housing. 7. Install the air filter housing cover (A). 8. Tighten the screws that secure the air filter housing cover to the air filter housing.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


247


ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, an authorized dealer should check the alignment of your headlamps.


Vertical Aim Adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.


• (A) 8 feet (2.4 meters) • (B) Center height of lamp to • (C) 25 feet (7.6 meters) • (D) Horizontal reference line


ground


2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height. 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. For Vehicles with Halogen Headlamps:


On the wall or screen you will observe a flat zone of high intensity light located at the top of the right hand portion of the beam pattern. If the top edge of the high intensity light zone is not at the horizontal reference line, the headlamp will need to be adjusted.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


248


Maintenance


For Vehicles with HID Headlamps:


There is a distinct cut-off (change from light to dark) in the left portion of the beam pattern. The top edge of this cut-off should be positioned 2 inches (5 centimeters) below the horizontal reference line.


4. Locate the vertical adjuster on each headlamp. Using a Phillips #2
screwdriver, turn the adjuster either clockwise or counterclockwise in order to aim the headlamp. The horizontal edge of the brighter light should touch the horizontal reference line.


5. Close the hood and turn off the lamps. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NOT ADJUSTABLE.


REMOVING A HEADLAMP


1. Make sure the headlamp control is in the off position and open the hood. 2. Remove the two screws from the headlamp assembly. 3. Carefully pull the headlamp assembly as far as possible towards the front of the vehicle to disengage it from the lower fixing point.


4. Carefully lift the outer side of the headlamp and remove it. 5. Disconnect the electrical connector.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


249


CHANGING A BULB


Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. These are examples of acceptable condensation: • Presence of thin mist (no streaks, drip marks or droplets). • Fine mist covers less than 50% of the lens. These are examples of unacceptable moisture (usually caused by a lamp water leak): • Water puddle inside the lamp. • Large water droplets, drip marks or streaks present on the interior of


the lens.


Take your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present.


Replacing Headlamp Bulbs


WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb by only its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.


Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


250


Maintenance


Install the new bulb in reverse order.


Headlamp assembly: A. High beam headlamp bulb B. Side marker bulb C. Low beam headlamp bulb D. Front parking lamp and turn signal bulb


High beam headlamp bulb: 1. Remove the headlamp assembly. 2. Remove the service cap. 3. Disconnect the electrical connector. 4. Remove the bulb from the headlamp assembly by turning it counterclockwise, then pull it straight out.


Low beam headlamp bulb: 1. Remove the headlamp assembly. 2. Remove the service cap. 3. Disconnect the electrical connector. 4. Remove the bulb from the headlamp assembly by turning it counterclockwise, then pull it straight out.


Install the new bulb in reverse order. Note: Be sure that the spring clip is not damaged or detached from the headlamp assembly during the replacement procedure. Replacing HID Headlamp Bulbs (If Equipped) The low beam headlamps on your vehicle use a high intensity discharge source. These lamps operate at a high voltage. When the bulb is burned out, the bulb and starter capsule assembly must be replaced by your authorized dealer.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


251


Replacing Front Parking Lamp and Turn Signal Bulbs


Replacing Side Marker Bulbs


1. Remove the service cap by turning it counterclockwise. 2. Remove the bulb socket from the headlamp assembly by turning it counterclockwise. 3. Remove the bulb by gently pulling the bulb straight out of the socket Install the new bulb in reverse order.


1. Remove the service cap. 2. Remove the bulb socket from the headlamp assembly by turning it counterclockwise. 3. Remove the bulb by gently pulling the bulb straight out of the socket Install the new bulb in reverse order.


Replacing Fog Lamp Bulbs (If Equipped)


1. Make sure the lighting control switch is in the off position. 2. Reach under the front fender and remove the aero shield. 3. Remove the harness/bulb assembly from the fog lamp by turning it counterclockwise. 4. Disconnect the harness from the bulb by pulling it straight out.


Install the new bulb in reverse order.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


252


Maintenance


Replacing Rear Lamps - Four Door


1. Make sure the headlamp control is in the off position and open the trunk. 2. Remove the trim panel from inside the luggage compartment. 3. Remove the two nuts from the lamp assembly


4. Gently pull the lamp assembly away from the vehicle 5. Remove the bulb by turning the bulb socket counterclockwise. Gently pull the bulb straight out of the socket.


• Turn signal bulb (1) • Stop and tail lamp bulb (2)


Install the new bulb in reverse order. Note: The reverse lamp bulb is located in the luggage compartment lid. If replacement is required, it is recommended that you see your authorized dealer.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Maintenance


253


Replacing Rear Lamps - Five Door


1. Make sure the headlamp control is in the off position and open the trunk. 2. Remove the trim panel from inside the luggage compartment. 3. Remove the two nuts from the lamp assembly


4. Gently pull the lamp assembly away from the vehicle 5. Remove the bulb by turning the bulb socket counterclockwise. Gently pull the bulb straight out of the socket.


A. Brake lamp bulb B. Reverse lamp bulb C. Tail lamp and side marker lamp bulb D. Turn signal bulb


Install the new bulb in reverse order. Replacing License Plate Lamp Assembly Your vehicle is equipped with an LED license plate lamp assembly. It is designed to last the life of the vehicle. If replacement is required, it is recommended that you see your authorized dealer. Replacing High-Mount Brake Lamp Assembly Your vehicle is equipped with an LED center high-mount stop lamp. It is designed to last the life of the vehicle. If replacement is required, it is recommended that you see your authorized dealer.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


254


Maintenance


BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.


Function


Trade number


Headlamp high beam Headlamp low beam (halogen) Headlamp low beam (HID) Turn lamp (front) Park/Side marker lamp (front) Fog lamps (if equipped) Stop/tail lamp Turn lamp Backup lamp Dome lamp


H1LL H11LL D8S W21W 168NA H11LL 3157K 3757AK


921


H5W or * LED if


equipped


* License plate lamp * High-mount brake lamp * To replace these lamps - see your authorized dealer. To replace all instrument panel lights - see your authorized dealer


LED LED


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Vehicle Care


255


GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes.


CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Detail Wash (ZC-3-A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (United States only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Quality Windshield Washer Fluid (Canada only) [CXC-37-(A, B, D or F)] Motorcraft Premium Windshield Wash Concentrate with Bitterant (United States only) (ZC-32-B2) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (United States only) (ZC-14) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Wheel and Tire Cleaner (ZC-37-A)


CLEANING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft® Detail Wash. • Never use strong household detergents or soap, such as dish washing


or laundry liquid. These products can discolor and spot painted surfaces.


strong, direct sunlight.


• Never wash a vehicle that is hot to the touch or during exposure to • Dry the vehicle with a chamois or soft terry cloth towel in order to • Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Motorcraft Bug and Tar Remover.


eliminate water spotting.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


256
• Note: Suntan lotions and insect repellents can damage any painted


Vehicle Care


surface; if these substances come in contact with your vehicle, wash it off as soon as possible.


• Remove any exterior accessories before entering a car wash. Stripes or Graphics (if equipped) Do not use a commercial or high-pressure wand on the surface or edge of stripes and graphics. This can cause damage to the film and cause the edge of the film to peel away from the vehicle surface.


Exterior Chrome Note: Never use abrasive materials such as steel wool or plastic pads as they can scratch the chrome surface. Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. • Wash the vehicle first, using cool or lukewarm water and a neutral pH • Use Motorcraft Custom Bright Metal Cleaner. Apply the product as


shampoo, such as Motorcraft Detail Wash.


you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.


• Do not apply cleaning product to hot surfaces and do not leave


cleaning product on chrome surfaces for a period of time exceeding that which is recommended. • Note: Using other non-recommended cleaners can result in severe


and permanent cosmetic damage.


Underbody Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.


Cleaning Plastic Exterior Parts Use only approved products to clean plastic parts. • For routine cleaning, use Motorcraft Detail Wash. • If tar or grease spots are present, use Motorcraft Bug and Tar


Remover.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Vehicle Care


257


WAXING Regular waxing is necessary to protect the paint on your car from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Always wash your vehicle before applying wax. • Use a quality wax that does not contain abrasives. • Follow the manufacturer’s instructions to apply and remove the wax. • Apply a small amount of wax in a back-and-forth motion, not in • Do not allow wax to come in contact with any non-body (low-gloss black) colored trim. The wax discolors or stains the parts over time, such as: • Bumpers • Grained door handles • Side mouldings • Mirror housings • Windshield cowl area.


• Do not apply wax to glass areas. • After waxing, your car’s paint should feel smooth, and be free of


circles.


streaks and smudges.


spots, road salt and industrial fallout, before repairing paint chips.


REPAIRING MINOR PAINT DAMAGE Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to an authorized dealer to make sure you get the correct color. • Remove particles, such as bird droppings, tree sap, insect deposits, tar • Always read the instructions before using the products. CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the


engine block or other engine components.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


258
• Spray Motorcraft Engine Shampoo and Degreaser on all parts that


Vehicle Care


running engine may cause internal damage.


require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo. • Never wash or rinse the engine while it is hot or running; water in the • Never wash or rinse any ignition coil, spark plug wire or spark plug • Cover the battery, power distribution box, and air filter assembly to


well, or the area in and around these locations.


prevent water damage when cleaning the engine.


CLEANING THE WINDOWS AND WIPER BLADES The windows and wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windows may be cleaned with a non-abrasive cleaner such as • The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft Premium Windshield Washer Concentrates in the U.S., or Motorcraft Premium Quality Windshield Washer Fluid in Canada. Replace your wiper blades when they appear worn or do not function properly.


Motorcraft® Ultra-Clear Spray Glass Cleaner.


• Do not use abrasive materials, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water. Note: Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Vehicle Care


259


CLEANING THE INTERIOR


WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt


webbing.


WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products


could contaminate the side airbag system and affect performance of the side airbag in a collision.


For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner. • Apply a layer of high quality foam cleaner, designed for automotive


interiors, to the dry stained area (s) of the item you are cleaning and allow soaking for one minute.


• If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover. In Canada, use Motorcraft Multi-Purpose Cleaner. • If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.


immediately (but do not oversaturate) or the ring can set.


CLEANING THE INSTRUMENT PANEL AND INSTRUMENT CLUSTER LENS


WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid


contamination of the airbag system.


Clean the instrument panel and cluster lens with a clean, damp, white, cotton cloth, then use a clean and dry, white, cotton cloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Vehicle Care


260
• Be certain to wash or wipe your hands clean if you have been in contact with certain products, such as insect repellent and suntan lotion, in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty.


finish of the instrument panel, interior trim and cluster lens.


If a staining liquid like coffee or juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white, cotton cloth. For more thorough cleaning, use a mild soap and water solution. If the spot cannot be completely cleaned by this method, the area may be cleaned using a commercially available cleaning product designed for automotive interiors. 3. If necessary, apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area; allow this to set at room temperature for 30 minutes. 4. Remove the soaked cloth, and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth.


CLEANING LEATHER SEATS (IF EQUIPPED) • Remove dust and loose dirt with a vacuum cleaner. • Clean spills and stains as quickly as possible. • For routine cleaning, wipe the surface with a soft, damp cloth. For


more thorough cleaning, wipe the surface with a mild soap and water solution. Dry the area with a soft cloth.


• If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available leather cleaning product designed for automotive interiors. • To check for compatibility, first test any cleaner or stain remover on


an inconspicuous part of the leather.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Vehicle Care


261


• Do not use household cleaning products, alcohol solutions,


oil/petroleum-based leather conditioners, or solvents or cleaners intended specifically for rubber, vinyl and plastics. These products may cause premature wearing or damage to the leather.


CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. A clearcoat paint finish coats aluminum wheels and wheel covers. In order to maintain their condition: • Clean weekly with Motorcraft Wheel and Tire Cleaner. Use a sponge to


remove heavy deposits of dirt and brake dust accumulation. Rinse thoroughly with a strong stream of water when you have completed the cleaning process.


• To remove tar and grease, use Motorcraft Bug and Tar Remover. • Never apply any cleaning chemical to hot or warm wheel rims or • Some automatic car washes may cause damage to the finish on your • Industrial-strength (heavy-duty) cleaners, or cleaning chemicals, in


wheel rims or covers.


covers.


combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.


• Do not use hydrofluoric acid-based or high caustic-based wheel • If you intend on parking your vehicle for an extended period after


cleaners, steel wool, fuels or strong household detergent.


cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so. This reduces the risk of increased corrosion of the brake discs.


VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), read the following maintenance recommendations to make sure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested for reliable, regular driving. Long-term storage under various conditions may lead to component degradation or failure unless specific precautions are taken to preserve the components.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


262


Vehicle Care


General • Store all vehicles in a dry, ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to


protect against rust and damage.


Body • Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and underside of front fenders. • Periodically wash vehicles stored in exposed locations. • Touch up raw or primed metal to prevent rust. • Cover chrome and stainless steel parts with a thick coat of auto wax


grade oil.


to prevent discoloration. Re-wax as necessary when the vehicle is washed.


• Lubricate hood latch, all door latches and trunk lid hinges with a light • Cover interior trim to prevent fading. • Keep all rubber parts free from oil and solvents. Engine • The engine oil and filter should be changed prior to storage, as used • Start the engine every 15 days. Run at fast idle until it reaches normal • With your foot on the brake, shift through all the gears while the


engine oil contains contaminates that may cause engine damage.


operating temperature.


engine is running.


Fuel system • Fill the fuel tank with high-quality fuel until the first automatic shutoff


of the fuel pump nozzle.


Cooling system • Protect against freezing temperatures. • When removing vehicle from storage, check coolant fluid level. Confirm there are no cooling system leaks, and fluid is at the recommended level.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Vehicle Care


263


Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting.


Note: If battery cables are disconnected, it will be necessary to reset memory features. Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are • Move vehicles at least 25 feet (8 meters) every 15 days to lubricate


covered with grease to prevent rust.


working parts and prevent corrosion.


window surfaces.


during storage (mice/squirrel nests).


Removing Vehicle from Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collected • Check the exhaust for any foreign material that may have collected • Check tire pressures and set tire inflation per the Tire Label. • Check brake pedal operation. Drive the vehicle 15 feet (4.5 meters) • Check fluid levels (including coolant, oil and gas) to make sure there • If the battery was removed, clean the battery cable ends and inspect. Contact your authorized dealer if you have any concerns or issues.


are no leaks and fluids are at recommended levels.


back and forth to remove rust build-up.


during storage.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


264


TIRE CARE


Wheels and Tires


IMPORTANT INFORMATION FOR 235/40R18 LOW-PROFILE TIRES AND WHEELS If your vehicle is equipped with 235/40R18 tires, they are low-profile tires. These tires and wheels are designed to give your vehicle a sport appearance. With low-profile tires, you may notice an increase in road noise and faster tire wear, depending on road conditions and driving styles. Due to their design, low-profile tires and wheels are more prone to road damage from potholes, rough or unpaved roads, car wash rails and curb contact than standard tires and wheels. Note: Your vehicle’s warranty does not cover these types of damage. Tires should always be kept at the correct inflation pressures and extra caution should be taken when operating on rough roads to avoid impacts that could cause wheel and tire damage.


Information About Uniform Tire Quality Grading


Tire Quality Grades apply to new pneumatic passenger car tires. The Tire Quality Grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, light truck or LT type tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


265


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 11⁄2
times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.


Traction AA A B C


WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include


acceleration, cornering, hydroplaning or peak traction characteristics.


The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.


Temperature A B C


WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


266


Wheels and Tires


Glossary of Tire Terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry.


• Tire Identification Number (TIN): A number on the sidewall of


each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code.


• Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a maximum load at set pressure. For example: For P-metric tires 35 psi (2.4 bar) or 36 (2.5 bar) depending on tire size and for Metric tires 36 psi (2.5 bar). Increasing the inflation pressure beyond this pressure will not increase the tire capability.


• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 42 psi (2.9 bar). Increasing the inflation pressure beyond this pressure will not increase the tire’s load-carrying capability.


• kPa: KiloPascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold tire pressure: The tire pressure when the vehicle has been


stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 kilometers). • Recommended inflation pressure: The cold inflation pressure found


on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position) or Tire Label located on the B-Pillar or the edge of the driver’s door.


front door.


• B-pillar: The structural member at the side of the vehicle behind the • Bead area of the tire: Area of the tire next to the rim. • Sidewall of the tire: Area between the bead area and the tread. • Tread area of the tire: Area of the perimeter of the tire that • Rim: The metal support (wheel) for a tire or a tire and tube assembly


contacts the road when mounted on the vehicle.


upon which the tire beads are seated.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


267


INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. Information on P Type Tires


P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.)


C D E


A. P: Indicates a tire, designated by the Tire and Rim Association, that may be used for service on cars, sport utility vehicles, minivans and light trucks. Note: If your tire size does not begin with a letter, this may mean it is designated by either the European Tire and Rim Technical Organization or the Japan Tire Manufacturing Association. B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. D. R: Indicates a radial type tire. E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


268


Wheels and Tires


F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s manual. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law. G. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h). These ratings are listed in the following chart. Note: You may not find this information on all tires because it is not required by federal law.


Letter rating


Speed rating - mph (km/h)


81 (130) 87 (140) 99 (159) 106 (171) 112 (180) 118 (190) 124 (200) 130 (210) 149 (240) 168 (270) 186 (299 )


Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


269


H. U.S. DOT Tire Identification Number (TIN): This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. See the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), for the correct tire pressure for your vehicle. L. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the


wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150
would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest, are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.


• Temperature: The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


270


Wheels and Tires


M. Maximum Inflation Pressure: Indicates the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the vehicle manufacturer’s recommended cold inflation pressure, which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings, such as standard load or radial tubeless. Additional Information Contained on the Tire Sidewall for LT Type Tires


LT type tires have some additional information beyond those of P type tires. These differences are described below. Note: Tire Quality Grades do not apply to this type of tire. A. LT: Indicates a tire, designated by the Tire and Rim Association, that is intended for service on light trucks. B. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits.


C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual, defined as four tires on the rear axle (a total of six or more tires on the vehicle). D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single, defined as two tires (total) on the rear axle.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


271


Information on T Type Tires


T type tires have some additional information beyond those of P type tires. These differences are described below. T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire.


A. T: Indicates a type of tire, designated by the Tire and Rim Association, that is intended for temporary service on cars, sport-utility vehicles, minivans and light trucks. B. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 80: Indicates the aspect ratio, which gives the tire’s ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D. D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.


Location of the Tire Label You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver’s door. See the payload description and graphic in the Load Carrying chapter.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


272


Wheels and Tires


INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company.


WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or blowout, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat build-up and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents. A tire can lose up to half of its air pressure and not appear to be flat! You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns. Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles. Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure, which can be found


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


273


on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label. When weather temperature changes occur, tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. Note: If you are checking tire pressure when the tire is hot (for example, driven more than 1 mile [1.6 kilometers]), never bleed or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended cold inflation pressure could be significantly under-inflated. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pressing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type mini-spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see Dissimilar Spare Tire and Wheel Assembly Information under Changing a Road Wheel in this chapter. Store and maintain at the higher of the front and rear inflation pressure as shown on the Tire Label.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


274


Wheels and Tires


6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts or bulges.


Inspecting Your Tires and Wheel Valve Stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist:


Tire Wear


When the tread is worn down to 1/16th of an inch (2 millimeters), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or wear bars, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 millimeters).


When the tire tread wears down to the same height as these wear bars, the tire is worn out and must be replaced.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


275


Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed or suspected, have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended.


WARNING: Age Tires degrade over time depending on many factors such as


weather, storage conditions, and conditions of use (such as load, speed, inflation pressure) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear. However, heat caused by hot climates or frequent high loading conditions can accelerate the aging process and may require tires to be replaced more frequently. You should replace your spare tire when you replace the road tires or after six years due to aging even if it has not been used.


U.S. DOT Tire Identification Number Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


276


Wheels and Tires


Tire Replacement Requirements


WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric


versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or the Tire Label which is located on the B-Pillar or edge of the driver’s door. If this information is not found on these labels, then you should contact your authorized dealer as soon as possible. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure. If you have questions regarding tire replacement, contact your authorized dealer as soon as possible.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


277


WARNING: To reduce the risk of serious injury, when mounting replacement tires and wheels, you should not exceed the


maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.38 bar) greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again. 3. Stand at a minimum of 12 feet (3.66 meters) away from the tire wheel assembly. 4. Use both eye and ear protection. For a mounting pressure more than 20 psi (1.38 bar) greater than the maximum pressure, a Ford dealer or other tire service professional should do the mounting. Always inflate steel carcass tires with a remote air fill with the person inflating standing at a minimum of 12 feet (3.66 meters) away from the tire wheel assembly.


Your vehicle is equipped with tires designed to provide a safe ride and handling capability. Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. The two front tires or two rear tires should generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the tire pressure monitoring system indicator is flashing, the system is malfunctioning. Your replacement tire might be incompatible with your tire pressure monitoring system, or some component of the system may be damaged.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


278


Wheels and Tires


Safety Practices


WARNING: If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause


an explosion. A tire can explode in as little as three to five seconds.


WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander.


Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits. • Avoid fast starts, stops and turns. • Avoid potholes and objects on the road. • Do not run over curbs or hit the tire against a curb when parking. Highway Hazards No matter how carefully you drive, there is always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under-inflated or damaged, deflate it, remove the wheel and replace it with your spare tire and wheel. If you cannot detect a cause, have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected.


Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you are driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically. Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front-wheel drive vehicles and those with an independent rear suspension may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


279


Tire Rotation Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire and wheel assembly. A dissimilar spare tire and wheel assembly is defined as a spare tire and wheel that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare tire and wheel assembly, it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements. Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information) will help your tires wear more evenly, providing better tire performance and longer tire life.


• Front-wheel drive vehicles (front


tires at left of diagram)


Sometimes irregular tire wear can be corrected by rotating the tires.


USING SNOW CHAINS


WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or


wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally, the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure.


Note: The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


280


Wheels and Tires


The tires on your vehicle may have all-weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. Use chains on the tires only in an emergency or if the law requires them. Follow these guidelines when using snow tires and chains: • If possible, avoid fully loading your vehicle. • Chains may damage aluminum wheels. • Use SAE Class S chains with 195/65R15 or 215/55R16 tires only; do • Install chains securely, verifying that the chains do not touch any • Drive cautiously. If you hear the chains rub or bang against your


not use tire chains with any other size tires.


wiring, brake lines or fuel lines.


vehicle, stop and retighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. • Remove the tire chains when they are no longer needed. Do not use


tire chains on dry roads.


TIRE PRESSURE MONITORING SYSTEM


WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure


should be checked periodically (at least monthly) using a tire gauge. See Inflating Your Tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.


Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


281


tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


282


Wheels and Tires


Changing Tires with a Tire Pressure Monitoring System


Note: Each road tire is equipped with a tire pressure sensor located inside the tire and wheel assembly cavity. The pressure sensor is attached to the valve stem. The pressure sensor is covered by the tire and is not visible unless the tire is removed. Take care when changing the tire to avoid damaging the sensor.


You should always have your tires serviced by an authorized dealer. Check the tire pressure periodically (at least monthly) using an accurate tire gauge. See Inflating Your Tires in this chapter.


Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low. Once the light is illuminated, your tires are under-inflated and need to be inflated to the manufacturer’s recommended tire pressure. Even if the light turns on and a short time later turns off, your tire pressure still needs to be checked. When Your Temporary Spare Tire Is Installed When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle. To restore the full function of the tire pressure monitoring system, have the damaged road wheel and tire assembly repaired and remounted on your vehicle.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


283


When You Believe Your System Is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. See the following chart for information concerning your tire pressure monitoring system: Low tire pressure warning light Solid warning light


Possible cause Customer action required


Tire(s) under-inflated


1. Make sure tires are at the proper pressure. See Inflating Your Tires in this chapter. 2. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off.


Spare tire in use Repair the damaged road wheel


and tire and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When Your Temporary Spare Tire is Installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible.


TPMS malfunction


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


284


Wheels and Tires


Low tire pressure warning light Flashing warning light


Possible cause Customer action required


Spare tire in use Repair the damaged road wheel


and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When Your Temporary Spare Tire is Installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible.


TPMS malfunction


When Inflating Your Tires When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires. It may take up to two minutes of driving over 20 mph (32 km/h) for the light to turn off after you have filled your tires to the recommended inflation pressure. How Temperature Affects Your Tire Pressure The tire pressure monitoring system monitors tire pressure in each pneumatic tire. While driving in a normal manner, a typical passenger tire inflation pressure may increase about 2 to 4 psi (14 to 28 kPa) from a cold start situation. If the vehicle is stationary overnight with the outside temperature significantly lower than the daytime temperature, the tire pressure may decrease approximately 3 psi (21 kPa) for a drop of 30°F (17°C) in ambient temperature. This lower pressure value may be detected by the tire pressure monitoring system as being significantly lower than the recommended inflation pressure and activate the system warning light for low tire pressure. If the low tire pressure warning light is on, visually check each tire to verify that no tire is flat. If one or more tires are flat, repair as necessary. Check the air pressure in the road tires. If any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


285


CHANGING A ROAD WHEEL


WARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However, if


you must use a sealant, have an authorized dealer install a new tire pressure monitoring system sensor and valve stem.


WARNING: See Tire Pressure Monitoring System in this chapter for important information. If the tire pressure monitoring


sensor becomes damaged, it will no longer function.


Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on this vehicle. If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Have a flat serviced by an authorized dealer in order to prevent damage to the system sensors. See Tire Pressure Monitoring System earlier in this chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the tire pressure monitoring system sensor for damage.


Dissimilar Spare Tire and Wheel Assembly Information


WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.


If you have a dissimilar spare tire and wheel assembly, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire and wheel assembly that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare tire and wheel assembly is defined as a spare tire or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


286


Wheels and Tires


Safety Compliance Label.


2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY When driving with one of the dissimilar spare tires listed above, do not: • exceed 50 mph (80 km/h). • load the vehicle beyond maximum vehicle load rating listed on the • tow a trailer. • use snow chains on the end of the vehicle with the dissimilar spare tire. • use more than one dissimilar spare tire at a time. • use commercial car washing equipment. • try to repair the dissimilar spare tire. Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire and wheel assembly, do not: • exceed 70 mph (113 km/h). • use more than one dissimilar spare tire and wheel at a time. • use commercial car washing equipment. • use snow chains on the end of the vehicle with the dissimilar spare


tire and wheel.


The usage of a full-size dissimilar spare tire and wheel assembly can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


287


• Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly, additional caution should be given to: • towing a trailer. • driving vehicles equipped with a camper body. • driving vehicles with a load on the cargo rack. Drive cautiously when using a full-size dissimilar spare tire and wheel, and seek service as soon as possible.


Tire Change Procedure


WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or


slipping off the jack, even if the transmission is in park (P) or neutral (N).


WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the transmission in park (P) or neutral (N), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.


WARNING: Never get underneath a vehicle that is supported only by a jack. If the vehicle slips off the jack, you or someone


else could be seriously injured.


WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to


avoid the danger of being hit when operating the jack or changing the wheel.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


288


Wheels and Tires


WARNING: Always use the jack provided as original equipment with your vehicle. If using a jack other than the one provided as


original equipment with your vehicle, make sure the jack capacity is adequate for the vehicle weight, including any vehicle cargo or modifications.


Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Park on a level surface, set the parking brake and activate the hazard flashers. 2. Place the transmission in park (P) or neutral (N) and turn the engine off.


3. Remove the carpeted wheel cover. 4. Remove the wing nut and bolt assembly that secures the spare tire and jack by turning it counterclockwise.


5. Remove the lug wrench and jack from the foam holder.


6. Block the diagonally opposite wheel.


7. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.


8. The vehicle jacking points are shown here, and are depicted on the yellow warning label on the jack. Note: Jack at the specified locations to avoid damage to the vehicle.


9. Remove the lug nuts with the lug wrench.


2014 Focus (foc) Owners Guide gf, 3rd Printing, February 2014
USA (fus)


Wheels and Tires


289


10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 11. Lower the wheel by turning the jack handle counterclockwise.


12. Remove the jack and fully tighten the lug nuts in the order shown. See Wheel Lug Nut Torque Specifications in this chapter for the proper lug nut torque specification. 13. Put the flat tire, jack and lug wrench away. Make sure the jack is fastened so it does not rattle when you drive. Unblock the wheels.

Loading...
x