Download PDF Manual

Detail Wash.


210


Fiesta (CCT), enUSA, Second Printing


Vehicle Care


• Do not allow wax to come in contact with any non-body (low-gloss black) colored trim. The wax will discolor or stain the parts over time. • Roof racks. • Bumpers. • Grained door handles. Side moldings. • • Mirror housings. • Windshield cowl area.


• Do not apply wax to glass areas. • After waxing, your car's paint should


feel smooth, and be free of streaks and smudges.


CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: •


Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.



• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. Spray Motorcraft Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo.


• Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage.


Exterior Plastic Parts For routine cleaning we recommend Motorcraft Detail Wash. If tar or grease spots are present, we recommend Motorcraft Bug and Tar Remover. Stripes or Graphics (If Equipped) Do not use a commercial or high-pressure sprayer on the surface or edge of stripes and graphics. This can damage them and cause the edges to peel away from the vehicle surface. Underbody Flush the complete underside of your vehicle frequently. Keep body and door drain holes free of debris or foreign material. WAXING Regular waxing is necessary to protect your car's paint from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Always wash your vehicle before applying wax. • Use a quality wax that does not contain


abrasives. Follow the manufacturer’s instructions to apply and remove the wax.



• Apply a small amount of wax in a


back-and-forth motion, not in circles.


211


Fiesta (CCT), enUSA, Second Printing


Vehicle Care


• Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations.


• Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine.



CLEANING THE WINDOWS AND WIPER BLADES Car wash chemicals and environmental fallout can result in windshield and wiper blade contamination. Dirty windshield and wipers will result in poor windshield wiper operation. Keep the windshield and wiper blades clean to maintain windshield wiper performance. To clean the windshield and wiper blades: • Clean the windshield with a non-abrasive glass cleaner. For windshields contaminated with tree sap, chemicals, wax or bugs, clean the entire windshield using steel wool (no greater than 0000 grade) in a circular motion and rinse with water. • Clean the wiper blades with isopropyl rubbing alcohol or windshield washer concentrate.


Note: Do not use razor blades or other sharp objects to clean or remove decals from the inside of the heated rear window. The vehicle warranty does not cover damage caused to the heated rear window grid lines. CLEANING THE INTERIOR


WARNINGS


Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the


belt webbing.


WARNINGS


On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.


For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a


vacuum cleaner.



• Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner. If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover. In Canada, use Motorcraft Multi-Purpose Cleaner. If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set.



• Do not use household cleaning


products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.


CLEANING THE INSTRUMENT PANEL AND INSTRUMENT CLUSTER LENS


WARNING


Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel


to avoid contamination of the airbag system.


212


Fiesta (CCT), enUSA, Second Printing


Vehicle Care


4.


If necessary, apply more soap and water solution or cleaning product to a clean, soft cloth and press it onto the soiled area. Allow this to set at room temperature for 30 minutes.


5. Remove the soaked cloth, then with a


clean, damp cloth, use a rubbing motion for 60 seconds on the soiled area.


6. Dry the area with a clean, soft cloth. CLEANING LEATHER SEATS (If Equipped) Note: Follow the same procedure as cleaning leather seats for cleaning leather instrument panels and leather interior trim surfaces. For routine cleaning, wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. For cleaning and removing spots and stains such as dye transfer, use Motorcraft Premium Leather and Vinyl Cleaner or a commercially available leather cleaning product for automotive interiors. Note: Test any cleaner or stain remover on an inconspicuous area. You should: • Remove dust and loose dirt with a


vacuum cleaner.


• Clean and treat spills and stains as


soon as possible.


Do not use the following products as these may damage the leather: • Oil and petroleum or silicone-based


leather conditioners. • Household cleaners.


Note: Follow the same procedure as cleaning leather seats for cleaning leather instrument panels and leather interior trim surfaces. See Cleaning Leather Seats (page 213). Clean the instrument panel and cluster lens with a clean, damp and soft cloth, then use a clean, dry and soft cloth to dry these areas. • Avoid cleaners or polishes that increase


the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect you from undesirable windshield reflection. • Do not use any household cleaning products or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.


• Wash or wipe your hands clean if you


have been in contact with certain products such as insect repellent and suntan lotion to avoid possible damage to the interior painted surfaces.


• Do not allow air fresheners and hand sanitizers to spill onto interior surfaces. If a spill occurs, wipe off immediately. Your warranty may not cover these damages.


If a staining liquid like coffee or juice has been spilled on the instrument panel or on interior trim surfaces: 1. Wipe up spilled liquid using a clean,


soft cloth as quickly as possible.


2. Use Motorcraft Premium Leather and


Vinyl Cleaner or a commercially available leather cleaning product for automotive interiors. Test any cleaner or stain remover on an inconspicuous area.


3. Alternatively, wipe the surface with a clean, soft cloth and a mild soap and water solution. Dry the area with a clean, soft cloth.


213


Fiesta (CCT), enUSA, Second Printing


Vehicle Care


• Alcohol solutions. •


Solvents or cleaners intended specifically for rubber, vinyl and plastics.


Note: Do not use Motorcraft Premium Leather and Vinyl Cleaner ZC-56 on Lincoln Black Label, Presidential or Reserve Leathers because it can damage those and other semi-aniline leather seating fabrics. It can also damage surround microfiber accent surfaces. To clean Lincoln Black Label, Presidential or Reserve Leathers, first vacuum the seats to remove loose dirt. Then wipe the leather with a clean soft cloth dampened with lukewarm water and a mild soap. Wiper the leather again with a slightly damp cloth to remove soap residue, and dry with a soft cloth. To maintain the leather's resiliency, it should be cleaned whenever soiled. REPAIRING MINOR PAINT DAMAGE You should repair paintwork damage caused by stones from the road or minor scratches as soon as possible. A choice of products are available from an authorized dealer. Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. Always read and follow the manufacturer’s instructions before using the products. CLEANING THE ALLOY WHEELS Note: Do not apply a cleaning chemical to warm or hot wheel rims and covers.


Note: Industrial-strength (heavy-duty) cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clear coat finish over a period of time. Note: Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergent. Note: If you intend parking your vehicle for an extended period after cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so. This will reduce the risk of increased corrosion of the brake discs, brake pads and linings. Note: Some automatic car washes may cause damage to the finish on your wheel rims and covers. Alloy wheels and wheel covers are coated with a clear coat paint finish. To maintain their condition we recommend that you: • Clean them weekly with the


recommended wheel and tire cleaner.


• Use a sponge to remove heavy deposits of dirt and brake dust accumulation.


• Rinse them thoroughly with a


pressurized stream of water when you have completed the cleaning process. We recommend that you use Ford service wheel cleaner. Make sure that you read and follow the manufacturer’s instructions. Using other non-recommended cleaning products can result in severe and permanent cosmetic damage. VEHICLE STORAGE If you plan on storing your vehicle for 30
days or more, read the following maintenance recommendations to make sure your vehicle stays in good operating condition.


214


Fiesta (CCT), enUSA, Second Printing


Vehicle Care


Engine • Change the engine oil and filter prior to


storage because used engine oil contains contaminates which may cause engine damage. Start the engine every 15 days for a minimum of 15 minutes. Run at fast idle with the climate controls set to defrost until the engine reaches normal operating temperature.



• With your foot on the brake, shift


through all the gears while the engine is running.


• We recommend that you change the engine oil before you use your vehicle again.


Fuel system •


Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle.


Cooling system • Protect against freezing temperatures. • When removing your vehicle from storage, check coolant fluid level. Confirm that there are no cooling system leaks and that fluid is at the recommended level.


Battery • Check and recharge as necessary. Keep


connections clean. If storing your vehicle for more than 30
days without recharging the battery, we recommend that you disconnect the battery cables to maintain battery charge for quick starting.


Note: It is necessary to reset memory features if battery cables are disconnected.



We engineer and test all motor vehicles and their components for reliable, regular driving. Under various conditions, long-term storage may lead to degraded engine performance or failure unless you use specific precautions to preserve engine components. General •


Store all vehicles in a dry, ventilated place.


• Protect from sunlight, if possible. If vehicles are stored outside, they • require regular maintenance to protect against rust and damage.


Body • Wash your vehicle thoroughly to


remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and the underside of front fenders. • Periodically wash your vehicle if it is


stored in exposed locations. Touch-up exposed or primed metal to prevent rust.



• Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when you wash your vehicle. Lubricate all hood, door and luggage compartment hinges and latches with a light grade oil.



• Cover interior trim to prevent fading. •


Keep all rubber parts free from oil and solvents.


215


Fiesta (CCT), enUSA, Second Printing


Vehicle Care


Contact an authorized dealer if you have any concerns or issues.


Brakes • Make sure the brakes and parking brake


release fully.


Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers


and pins under your vehicle are covered with grease to prevent rust.


• Move vehicles at least 25 ft (7.5 m)


every 15 days to lubricate working parts and prevent corrosion.


Removing Vehicle From Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt


or grease film build-up on window surfaces.


• Check windshield wipers for any


deterioration.


• Check under the hood for any foreign


material that may have collected during storage such as mice or squirrel nests.


• Check the exhaust for any foreign material that may have collected during storage.


• Check tire pressures and set tire


inflation per the Tire Label.


• Check brake pedal operation. Drive your vehicle 15 ft (4.5 m) back and forth to remove rust build-up.


• Check fluid levels (including coolant, oil and gas) to make sure there are no leaks, and fluids are at recommended levels. If you remove the battery, clean the battery cable ends and check for damage.



216


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


GENERAL INFORMATION A decal with tire pressure data is located in the driver’s door opening. Check and set the tire pressure at the ambient temperature in which you are intending to drive your vehicle and when the tires are cold. Note: Check your tire pressures regularly to optimize fuel economy. Note: Use only approved wheel and tire sizes. Using other sizes could damage your vehicle and will make the National Type Approval invalid. Note: If you change the diameter of the tires from that fitted at the factory, the speedometer may not display the correct speed. Take your vehicle to an authorized dealer to have the engine management system reprogrammed. Note: If you intend to change the size of the wheels from that fitted at the factory, check the suitability with an authorized dealer. TIRE CARE Important information for 205/40R17 low-profile tires and wheels If your vehicle is equipped with 205/40R17 tires, they are low-profile tires. These tires and wheels are designed to give your vehicle a sport appearance. With low-profile tires, you may notice an increase in road noise and faster tire wear, depending on road conditions and


driving styles. Due to their design, low-profile tires and wheels are more prone to road damage from potholes, rough or unpaved roads, car wash rails and curb contact than standard tires and wheels. Note: Your vehicle’s warranty does not cover these types of damage. Tires should always be kept at the correct inflation pressures and extra caution should be taken when operating on rough roads to avoid impacts that could cause wheel and tire damage. Information About Uniform Tire Quality Grading


Tire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200
Traction AA Temperature A. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.


217


Fiesta (CCT), enUSA, Second Printing


E142542 Wheels and Tires


Tire Quality Grades apply to new pneumatic passenger car tires. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, light truck or LT type tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104 (c)(2). U.S. Department of Transportation Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150
would wear one and one-half (1
½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.


Traction AA A B C


WARNING


The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.


The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Temperature A B C


WARNING


The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory


218


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Glossary of Tire Terminology * Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry. *Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. *Inflation pressure: A measure of the amount of air in a tire. *Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 psi (2.5 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability.


*Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. *kPa: Kilopascal, a metric unit of air pressure. *PSI: Pounds per square inch, a standard unit of air pressure. *Cold tire pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 kilometers). *Recommended inflation pressure: The cold inflation pressure found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-Pillar or the edge of the driver’s door. *B-pillar: The structural member at the side of the vehicle behind the front door * Bead area of the tire: Area of the tire next to the rim. * Sidewall of the tire: Area between the bead area and the tread.


219


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


* Tread area of the tire: Area of the perimeter of the tire that contacts the road when mounted on the vehicle. *Rim: The metal support (wheel) for a tire or a tire and tube assembly upon which the tire beads are seated. Information Contained on the Tire Sidewall Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall.


Information on P Type Tires


P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) A. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks. Note: If your tire size does not begin with a letter this may mean it is designated by either ETRTO (European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing Association).


220


Fiesta (CCT), enUSA, Second Printing


HIJKLMABCDEFGE142543 Wheels and Tires


B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 65: Indicates the aspect ratio which gives the tire's ratio of height to width. D. R: Indicates a radial type tire. E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. F. 95: Indicates the tire's load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s manual. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law. G. H: Indicates the tire's speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130
km/h) to 186 mph (299 km/h). These ratings are listed in the following chart.


Note: You may not find this information on all tires because it is not required by federal law.


Letter rating


Speed rating - mph


(km/h)


81 mph (130 km/h) 87 mph (140 km/h) 99 mph (159 km/h) 106 mph (171 km/h) 112 mph (180 km/h) 118 mph (190 km/h) 124 mph (200 km/h) 130 mph (210 km/h) 149 mph (240 km/h) 168 mph (270 km/h) 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299
km/h), tire manufacturers always use the letters ZR. H. U.S. DOT Tire Identification Number (TIN): This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are


221


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000
the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), for the correct tire pressure for your vehicle. L. Treadwear, Traction and Temperature Grades:


*Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. *Traction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. *Temperature: The temperature grades are A (the highest), B and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. M. Maximum Inflation Pressure: Indicates the tire manufacturers' maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the vehicle manufacturer's recommended cold inflation pressure which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge


222


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc. Additional Information Contained on the Tire Sidewall for LT Type Tires Note: Tire Quality Grades do not apply to this type of tire.


A. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. B. Load Range and Load Inflation Limits: Indicates the tire's load-carrying capabilities and its inflation limits. C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual; defined as four tires on the rear axle (a total of six or more tires on the vehicle). D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single; defined as two tires (total) on the rear axle. Information on T Type Tires T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire.


LT type tires have some additional information beyond those of P type tires; these differences are described below.


223


Fiesta (CCT), enUSA, Second Printing


ABCBDE142544 Wheels and Tires


C. 80: Indicates the aspect ratio which gives the tire's ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D.D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. Location of the Tire Label You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver’s door. Inflating Your Tires Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company.


T type tires have some additional information beyond those of P type tires; these differences are described below: A. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. B. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire.


224


Fiesta (CCT), enUSA, Second Printing


ABCDEE142545 Wheels and Tires


(affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles Maximum Inflation Pressure is the tire manufacturer's maximum permissible pressure and the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label.


You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns


WARNING


Under-inflation is the most common cause of tire failures


and may result in severe tire cracking, tread separation or blowout, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents. A tire can lose up to half of its air pressure and not appear to be flat!


Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label


225


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pressing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T type mini-spare tires (refer to the Dissimilar spare wheel and tire assembly information for a description): Store and maintain at 60 psi (4.15
bar). For full-size and dissimilar spare tires (refer to the Dissimilar spare wheel and tire assembly information for a description): Store and maintain at the higher of the front and rear inflation pressure as shown on the Tire Label. 6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts or bulges.


When weather temperature changes occur, tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1
psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. Note: If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never bleed or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended cold inflation pressure could be significantly under-inflated. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure.


226


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


Inspecting Your Tires and Wheel Valve Stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist:


Tire Wear


When the tread is worn down to one sixteenth of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or wear bars, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to one sixteenth of an inch (2 mm) When the tire tread wears down to the same height as these wear bars, the tire is worn out and must be replaced. Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed


227


Fiesta (CCT), enUSA, Second Printing


E142546 Wheels and Tires


or suspected have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended. Age


WARNING


Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear. However, heat caused by hot climates or frequent high loading conditions can accelerate the aging process and may require tires to be replaced more frequently. You should replace your spare tire when you replace the road tires or after six years due to aging even if it has not been used. U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and


describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000
the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. Tire Replacement Requirements Your vehicle is equipped with tires designed to provide a safe ride and handling capability. WARNINGS


Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size


228


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


WARNINGS


may be found on either the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or the Tire Label which is located on the B-Pillar or edge of the driver’s door. If this information is not found on these labels then you should contact your authorized dealer as soon as possible. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure. If you have questions regarding tire replacement, contact your authorized dealer as soon as possible.


When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.


WARNINGS


When inflating the tire for mounting pressures up to 20 psi (1.38 bar) greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again. 3. Stand at a minimum of 12 ft (3.66 m) away from the wheel and tire assembly. 4. Use both eye and ear protection. For a mounting pressure more than 20 psi (1.38 bar) greater than the maximum pressure, a Ford dealer or other tire service professional should do the mounting. Always inflate steel carcass tires with a remote air fill with the person inflating standing at a minimum of 12 ft (3.66 m) away from the wheel and tire assembly


Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle


229


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


*Avoid potholes and objects on the road *Do not run over curbs or hit the tire against a curb when parking Highway Hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under-inflated or damaged, deflate it, remove wheel and replace it with your spare tire and wheel. If you cannot detect a cause, have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected.


It is recommended that the two front tires or two rear tires generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the TPMS indicator is flashing, your TPMS is malfunctioning. Your replacement tire might be incompatible with your TPMS, or some component of the TPMS may be damaged. Safety Practices


WARNINGS


If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.


Do not spin the wheels at over 35 mph (56 km/h). The


tires may fail and injure a passenger or bystander.


Driving habits have a great deal to do with your tire mileage and safety. *Observe posted speed limits *Avoid fast starts, stops and turns


230


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically. Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front-wheel drive vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire Rotation Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.


Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare wheel and tire assembly it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements. Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. Front-wheel drive vehicles (front tires on the left side of the diagram)


Sometimes irregular tire wear can be corrected by rotating the tires.


231


Fiesta (CCT), enUSA, Second Printing


E142547 Wheels and Tires


Summer Tires Your Ford vehicle may be equipped with summer tires to provide superior performance on wet and dry roads. Summer tires do not have the Mud and Snow (M+S or M/S) tire traction rating on the tire side wall. Since summer tires do not have the same traction performance as All-season or Snow tires, Ford does not recommend using summer tires when temperatures drop to approximately 40°F (5°C) or below (depending on tire wear and environmental conditions) or in snow and ice conditions. Like any tire, summer tire performance is affected by tire wear and environmental conditions. If you must drive in those conditions, Ford recommends using Mud and Snow (M+S, M/S), All-season or Snow tires. USING WINTER TIRES


WARNING


When you use winter tires on your vehicle, you must make sure that you use the correct lug nuts.


If winter tires are used, you must make sure that you use the correct tire pressures. USING SNOW CHAINS


WARNING


Your vehicle is not approved for use with snow chains.


TIRE PRESSURE MONITORING SYSTEM


WARNING


The tire pressure monitoring system is not a substitute for manually checking tire pressure. The tire


pressure should be checked periodically (at least monthly) using a tire gauge, see Inflating your tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.


Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure


recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.


232


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.


Changing Tires With a Tire Pressure Monitoring System


Note: Each road tire is equipped with a tire pressure sensor located inside the wheel and tire assembly cavity. The pressure sensor is attached to the valve stem. The pressure sensor is covered by the tire and is not visible unless the tire is removed. Take care when changing the tire to avoid damaging the sensor You should always have your tires serviced by an authorized dealer. Check the tire pressure periodically (at least monthly) using an accurate tire gauge. See Inflating Your Tires in this chapter. Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low. Once the light is illuminated, your tires are under-inflated and need to be inflated to the manufacturer’s recommended tire pressure. Even if the light turns on and a short time later turns off, your tire pressure still needs to be checked.


233


Fiesta (CCT), enUSA, Second Printing


E142549 Wheels and Tires


When Your Temporary Spare Tire is Installed When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle. To restore the full function of the tire pressure monitoring system, have the damaged road wheel and tire assembly repaired and remounted on your vehicle.


When You Believe Your System is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. See the following chart for information concerning your tire pressure monitoring system:


234


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


Low tire pressure


warning light


Possible cause


Customer action required


Make sure tires are at the proper pres- sure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off. Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible. Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible.


It may take up to two minutes of driving over 20 mph (32 km/h) for the light to turn off after you have filled your tires to the recommended inflation pressure


Solid warning light


Tire(s) under-inflated


Spare tire in use


TPMS malfunction


Flashing warning


light


Spare tire in use


TPMS malfunction


When Inflating Your Tires When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires.


235


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


How Temperature Affects Your Tire Pressure The tire pressure monitoring system monitors tire pressure in each pneumatic tire. While driving in a normal manner, a typical passenger tire inflation pressure may increase about 2 to 4 psi (14 to 28
kPa) from a cold start situation. If the vehicle is stationary overnight with the outside temperature significantly lower than the daytime temperature, the tire pressure may decrease about 3 psi (21
kPa) for a drop of 30°F (17°C) in ambient temperature. This lower pressure value may be detected by the tire pressure monitoring system as being significantly lower than the recommended inflation pressure and activate the system warning light for low tire pressure. If the low tire pressure warning light is on, visually check each tire to verify that no tire is flat. If one or more tires are flat, repair as necessary. Check the air pressure in the road tires. If any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. CHANGING A ROAD WHEEL


WARNINGS


The use of tire sealants may damage your tire pressure monitoring system and should only be used in roadside emergencies. If you must use a sealant, the Ford Tire Mobility Kit sealant should be used. The tire pressure monitoring system sensor and valve stem on the wheel must be replaced by an authorized dealer after use of the sealant.


See Tire Pressure Monitoring System (page 232). If the tire pressure monitor sensor becomes damaged, it will no longer function.


Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Have a flat serviced by an authorized dealer in order to prevent damage to the tire pressure monitoring system sensors. See Tire Pressure Monitoring System (page 232). Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have an authorized dealer inspect the tire pressure monitoring system sensor for damage. Dissimilar Spare Wheel and Tire Assembly Information WARNING


Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.


If you have a dissimilar spare wheel and tire, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road wheel and tire assembly that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels and can be one of three types:


236


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking


performance.


• Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability When driving with the full-size dissimilar spare wheel and tire assembly additional caution should be given to: • • Driving vehicles equipped with a


Towing a trailer.


camper body.


• Driving vehicles with a load on the


cargo rack.


Drive cautiously when using a full-size dissimilar spare wheel and tire assembly and seek service as soon as possible. Tire Change Procedure WARNINGS


When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from


moving or slipping off the jack, even if the transmission selector lever is in park (P).


To help prevent your vehicle from moving when you change a tire, be sure to place the transmission selector lever in park (P), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.


Never get underneath a vehicle that is supported only by a jack. If your vehicle slips off the jack, you or


someone else could be seriously injured.


1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY. When driving with one of the dissimilar spare tires listed above, do not: Exceed 50 mph (80 km/h). • Load the vehicle beyond maximum • vehicle load rating listed on the Safety Compliance Label. Tow a trailer.


• • Use more than one dissimilar spare tire


at a time.


• Use commercial car washing


equipment. Try to repair the dissimilar spare tire.


• Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking


performance.


• Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability (if


applicable).


3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare wheel and tire assembly, do not: • • Use more than one dissimilar spare wheel and tire assembly at a time.


Exceed 70 mph (113 km/h).


• Use commercial car washing


equipment.


237


Fiesta (CCT), enUSA, Second Printing


Wheels and Tires


8. Block the diagonally opposite wheel. 9. Loosen each wheel lug nut one-half


turn counterclockwise but do not remove them until the wheel is raised off the ground.


Note: Jack at the specified locations to avoid damage to the vehicle. 10. The vehicle jacking points are shown here, and are depicted on the yellow warning label on the jack.


11.


Indentations in the sills show the location of the jacking points.


WARNINGS


Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.


Always use the jack provided as original equipment with your vehicle. If using a jack other than the one


provided as original equipment with your vehicle, make sure the jack capacity is adequate for the vehicle weight, including any vehicle cargo or modifications.


Make sure there is no lubrication (grease or oil) on the threads or the surface between the wheel lugs and nuts. This can cause the lug nuts to loosen while driving.


Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Park on a level surface, set the parking brake and activate the hazard flashers. 2. Place the transmission selector lever in park (P) (automatic transmission) or reverse (R) (manual transmission) and turn the engine off.


3. Remove the carpeted wheel cover. 4. Remove the spare tire bolt securing the


spare tire by turning it counterclockwise.


5. Remove the spare tire from the spare


tire compartment.


6. Remove the retaining bolt securing the


jack by turning it counterclockwise.


7. Remove the jack.


238


Fiesta (CCT), enUSA, Second Printing


E142551E145908E142553 Wheels and Tires


12. Remove the lug nuts with the lug


wrench.


13. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. Lower the wheel by turning the jack handle counterclockwise.


14.


15. Remove the jack and fully tighten the


lug nuts in the order shown. See Technical Specifications (page 240).


Stowing the Flat Tire The full-size road wheel can be stowed in the spare tire compartment. 1. Lift the carpeted wheel cover at an


angle to access the spare tire compartment.


2. Place the wheel in the spare tire well with the valve stem facing down. Use the mini-spare bolt to secure the wheel.


3. Place the jack and tools back into the


spare tire compartment.


4. Replace the carpeted wheel cover.


239


Fiesta (CCT), enUSA, Second Printing


1234E90589 Wheels and Tires


TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications


WARNING


When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while your vehicle is in motion, resulting in loss of control.


Bolt size M12 x 1.5


Ib-ft (Nm)* 100 (135)


*Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. Retighten the lug nuts to the specified torque within 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal).


Wheel pilot bore


Inspect the wheel pilot bore and mounting surface prior to installation. Remove any visible corrosion or loose particles.


240


Fiesta (CCT), enUSA, Second Printing


E145950 Capacities and Specifications


ENGINE SPECIFICATIONS 1.0L EcoBoost


Engine


Cubic inches Required fuel Compression


ratio


Spark plug gap


1.6L Duratec-16V Ti-


VCT 98


1.6L EcoBoost


98


61


Minimum 87 octane


Minimum 87 octane


Minimum 87 octane


10:1


11:1


10:1


0.026–0.030 in (0.65–0.75 mm)


0.028–0.031 in (0.7–0.8 mm)


0.028–0.031 in (0.7–0.8 mm)


Drivebelt Routing 1.0L EcoBoost


1.6L Duratec-16V Ti-VCT


1.6L EcoBoost


241


Fiesta (CCT), enUSA, Second Printing


E163197E163198E161372 Capacities and Specifications


MOTORCRAFT PARTS Component


1.0L EcoBoost


Air filter element1


Oil filter2
Battery


Spark plugs3
Cabin air filter Windshield wiper blade


SP-538A


1.6L Duratec-16V Ti-


VCT FA-1914


1.6L EcoBoost


FL-910S


BXT-96R-500
BXT-96R-590


SP-525


FP-69


SP-532


WW-1613 (driver side)


WW-2430 (passenger side)


WW-1204 (rear)


We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance. These parts meet or exceed Ford Motor Company’s specifications and are engineered for your vehicle. Use of other parts may impact vehicle performance, emissions and durability. Your warranty may be void for any damage related to use of other parts. If a Motorcraft oil filter is not available, use an oil filter that meets industry performance specification SAE/USCAR-36. For spark plug replacement, contact an authorized dealer. Replace the spark plugs at the appropriate intervals. See Normal Scheduled Maintenance (page 399).


242


Fiesta (CCT), enUSA, Second Printing


Capacities and Specifications


VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel.


Make, vehicle line, series, body type Engine type Check digit Model year Assembly plant Production sequence number


VEHICLE CERTIFICATION LABEL


Please note that in the graphic, XXXX is

Loading...
x