Download PDF Manual

interval between wipes will decrease. WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat.


Push the button to operate the washers. When you release the button, the wipers will operate for a short time.


WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Install new wiper blades as soon as they begin to leave bands of water and smears on the windshield. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.


Single wipe Intermittent wipe Normal wipe High speed wipe


Note: If you press and hold the wiper lever in position A, the wipers will continue to wipe until you release the wiper lever.


63


Fiesta (CCT), enUSA, Second Printing


E102032BACDE102033ABCE102051 Wipers and Washers


REAR WINDOW WIPER AND WASHERS Intermittent Wipe


Pull the lever toward you to operate the washers. They will operate for a maximum of 10 seconds. When you release the lever, the wiper will operate for a short time.


Pull the lever toward you. Reverse Gear Wipe The rear wiper will turn on automatically when selecting reverse gear if: •


the rear wiper is not already switched on the wiper lever is in position A, B, C or the front wiper is operating (when set to position B).




Rear Window Washer Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat.


64


Fiesta (CCT), enUSA, Second Printing


E102052E102053 Lighting


GENERAL INFORMATION Condensation in Lamp Assemblies Exterior lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. Examples of acceptable condensation are: • The presence of a fine mist (no streaks, drip marks or large droplets).


• A fine mist covers less than 50% of the


lens.


Examples of unacceptable condensation are: • A water puddle inside the lamp. •


Streaks, drip marks or large droplets present on the interior of the lens.


If you see any unacceptable condensation, have your vehicle checked by an authorized dealer.


LIGHTING CONTROL Lighting Control Positions


Off Parking lamps, instrument panel lamps, license plate lamps and tail lamps Headlamps


Parking Lamps Note: Prolonged use of the parking lamps when the ignition is off will cause the battery to run out of charge. To operate the parking lamps turn the lighting control to position B. The parking lamps operate with the ignition on or off.


65


Fiesta (CCT), enUSA, Second Printing


E156651ABC Lighting


High Beams


Pull the lever fully toward you to switch the high beams on. Pull the lever fully toward you again to switch the high beams off. Headlamp Flasher Pull the lever toward you slightly and release it to flash the headlamps. AUTOLAMPS (If Equipped)


WARNING


The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting


during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog. Make sure the headlamps are switched to auto or on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.


When the lighting control is in the autolamps position, the headlamps automatically turn on in low light situations or when the wipers turn on. The headlamps remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps remain on. See Information Displays (page 83). Note: With the headlamps in the autolamps position, you cannot switch the high beam headlamps on until the autolamps system turns the low beam headlamps on. Windshield Wiper Activated Headlamps The windshield wiper activated headlamps turn on within 10 seconds when you switch the windshield wipers on and the lighting control is in the autolamps position. They turn off approximately 60 seconds after you switch the windshield wipers off.


66


Fiesta (CCT), enUSA, Second Printing


E101829E158778 Lighting


The headlamps will not turn on by wiper activation: • During a single wipe. • When the wipers are on to clear washer


fluid during a wash condition. If the wipers are in intermittent mode.


• Note: If you switch autolamps and autowipers on, the headlamps will automatically turn on when the windshield wipers continuously operate. INSTRUMENT LIGHTING DIMMER


DAYTIME RUNNING LAMPS (If Equipped)


WARNING


The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting


during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog. Make sure the headlamps are switched to auto or on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.


The system switches the headlamps on in daylight conditions. To switch the system on: 1. Switch the ignition on. 2. Turn the lighting control to the off, autolamp or parking lamp position. 3. Make sure the transmission selector


lever is not in position P.


FRONT FOG LAMPS (If Equipped)


HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on.


67


Fiesta (CCT), enUSA, Second Printing


E156652E156823 Lighting


Pull the control to switch the fog lamps on or off. You cannot switch the fog lamps on when the lighting control is in the off or autolamps position. DIRECTION INDICATORS


INTERIOR LAMPS Front Interior Lamps


Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change.


Door contact Off Reading lamps


Off Door contact On Reading lamps


68


Fiesta (CCT), enUSA, Second Printing


E102016E156878ABCCE170657BCDAD Lighting


AMBIENT LIGHTING (If Equipped) The ambient lighting system illuminates the interior with a choice of several colors. The ambient lighting control is located on the instrument panel.


Press and release the switch to cycle through the color choices and the off condition.


The ambient lighting will switch on when the following conditions have been met: You switch the ignition on. • You switch the headlamps on. • • The exterior ambient light level is low. The ambient lighting will remain on until you switch the ignition off and one of the following conditions have been met: • •


You lock your vehicle. The accessory delay timer expires.


Reading lamps.


When the switch is set to the door contact position, the courtesy lamp will illuminate when you unlock or open a door or the liftgate. If you leave a door open with the ignition switched off, the courtesy lamp will go off automatically after some time to prevent your vehicle battery from losing charge. To switch it back on, switch the ignition on for a short time. The courtesy lamp will also illuminate when you switch the ignition off. It will go off automatically after a short time or when you start the engine. Reading Lamps If you switch the ignition off, the reading lamps will go off automatically after some time to prevent your vehicle battery from losing charge. To switch them back on, switch the ignition on for a short time. Rear Interior Lamps (If Equipped) Press to switch individual lamps on and off.


69


Fiesta (CCT), enUSA, Second Printing


E170600DE158830 Windows and Mirrors


POWER WINDOWS (If Equipped)


Window Lock


WARNINGS


Do not leave children unattended in your vehicle and do not let them play with the power windows. They may


seriously injure themselves.


When closing the power windows, you should verify they are free of obstructions and make sure that


children and pets are not in the proximity of the window openings.


Press the control to open the window. Lift the control to close the window. Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. One-Touch Down (If Equipped) Press the control fully and release it. Press again or lift it to stop the window. One-Touch Up (If Equipped) Lift the control fully and release it. Press or lift it again to stop the window.


70


Fiesta (CCT), enUSA, Second Printing


Press the control to lock or unlock the rear window controls. It lights when the rear window controls lock. Bounce-Back (If Equipped) The window stops automatically while closing. It reverses some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature


WARNING


When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care


when closing the windows to avoid personal injury or damage to your vehicle.


Proceed as follows to override this protection feature when there is a resistance, for example in winter: 1. Close the window twice until it reaches


the point of resistance and let it reverse.


E70848E70850 Windows and Mirrors


2. Close the window a third time to the point of resistance. You disabled the bounce-back feature and you can now close the window manually. The window travels past the point of resistance and you can close it fully. Contact an authorized dealer as soon as possible if the window does not close after the third attempt. Resetting the Bounce-Back Feature


WARNING


The bounce-back feature remains turned off until you reset the memory.


If you have disconnected the battery, you must reset the bounce-back memory separately for each window. 1. Lift and hold the control until the


window is fully closed.


2. Release the control. 3. Lift and hold the control again for a few


seconds.


4. Release the control. 5. Lift and hold the control again for a few


seconds.


6. Release the control. 7. Press and hold the control until the


window is fully open.


8. Lift and hold the control until the


window is fully closed.


9. Release the control. 10. Open the window and then try to


close it automatically. Repeat the procedure if the window does not close automatically.


11.


Accessory Delay (If Equipped) You can use the window controls for several minutes after switching off the ignition or until opening either front door. GLOBAL OPENING AND CLOSING You can also operate the power windows with the ignition off using the global opening and global closing function. Note: Global opening will only operate for a short period of time after you have unlocked your vehicle using the remote control. Note: Global closing will only operate if you have set the memory correctly for each window. See Power Windows (page 70). Global Opening (If Equipped)


To open all the windows: 1. Press and release the remote control


unlock button.


2. Press and hold the remote control


unlock button for at least three seconds.


71


Fiesta (CCT), enUSA, Second Printing


E71955 Windows and Mirrors


WARNING


Take care when using global closing. In an emergency, touch a door handle lock sensor to stop.


Note: Global closing can be switched on using the driver’s door handle. Global opening and closing can also be switched on using the buttons on the passive key. To close all the windows, press and hold the driver’s door handle for at least three seconds. The bounce-back function is also on during global closing. EXTERIOR MIRRORS Power Exterior Mirrors WARNING


Do not adjust the mirrors when your vehicle is moving. This could result in the loss of control of your vehicle,


serious personal injury or death.


Left-hand mirror Off Right-hand mirror


Press the lock or unlock button to stop the opening function. Global Closing (If Equipped) Vehicles Without Keyless Entry


WARNING


Take care when using global closing. In an emergency, press the lock or unlock button immediately to stop.


To close all the windows, press and hold the remote control lock button for at least three seconds. Press the lock or unlock button to stop the closing function. The bounce-back function is also on during global closing. Vehicles With Keyless Entry


72


Fiesta (CCT), enUSA, Second Printing


E71956E87384E71280BCA Windows and Mirrors


Move the controller in the direction of the arrows to adjust the mirror. Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Integrated Blind Spot Mirrors (If Equipped)


WARNING


Objects in the blind spot mirror are closer than they appear.


Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to increase your visibility along the side of your vehicle. Check the main mirror first before a lane change, then check the blind spot mirror. If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.


73


Fiesta (CCT), enUSA, Second Printing


The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C). INTERIOR MIRROR WARNING


Do not adjust the mirror when your vehicle is moving.


E71281ABCE138665 Windows and Mirrors


Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up. MOONROOF (If Equipped) WARNINGS


Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously


hurt themselves.


When closing the moonroof, you should verify that it is free of obstructions and make sure that


children and pets are not in the proximity of the roof opening.


The moonroof controls are located on the overhead console.


74


Fiesta (CCT), enUSA, Second Printing


Opening and Closing the Moonroof Press and release the rear of the SLIDE control to open the moonroof. The sliding shade will automatically open, if closed, while the moonroof opens. Press and hold the front of the SLIDE control to close the moonroof. Note: The sliding shade will not automatically close. Moonroof Sliding Shade You can manually open or close the sliding shade when the moonroof is closed. Slide the shade backward or forward to open or close it. Venting the Moonroof Press and hold the rear of the TILT control to vent the moonroof. Press and hold the front of the TILT control to close the moonroof.


E156620 Instrument Cluster


GAUGES


Tachometer Information display and engine coolant temperature gauge Speedometer Fuel gauge Tripmeter reset button


Compass (If Equipped) Displays the vehicle’s heading direction. To calibrate and set the compass zone use the information display menu. See Information Displays (page 83). Use the diagram to determine your magnetic zone.


75


Fiesta (CCT), enUSA, Second Printing


E102660CADEB123456789101112131415E142800 Instrument Cluster


Engine Coolant Temperature Gauge


Anti-lock Braking System Warning Lamp


Displays the temperature of the engine coolant. At normal operating temperature the indicator will remain in the center section. Fuel Gauge Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when your vehicle is moving or on a gradient. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. WARNING LAMPS AND INDICATORS - 1.6L DURATEC- 16V TI-VCT (SIGMA)/1.0L ECOBOOST™ The following warning lamps and indicators alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not illuminate when you start your vehicle.


If it illuminates when you are driving, this indicates a malfunction.


You will continue to have the normal braking system (without anti-lock braking system) unless the brake system warning lamp is also illuminated. Have your vehicle checked by an authorized dealer. Brake System Warning Lamp


It illuminates when you engage the parking brake and the ignition is on. If it illuminates


when your vehicle is moving, make sure the parking brake is disengaged. If the parking brake is disengaged, this indicates low brake fluid level or a brake system fault. Have your vehicle checked immediately by an authorized dealer.


WARNING


Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control Indicator


It will illuminate when you switch this feature on. See Using Cruise Control (page 139).


76


Fiesta (CCT), enUSA, Second Printing


E140760E138644E71340 Instrument Cluster


Direction Indicator


Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the


indicators stay on or flash faster, check for a burnt out bulb. See Changing a Bulb (page 194). Door Ajar Warning Lamp


Illuminates when you switch the ignition on and remains on if any door, the hood or the liftgate is


not closed properly. Engine Coolant Temperature Warning Lamp


Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Coolant Check (page 183). Front Airbag Warning Lamp


If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have your vehicle checked by an authorized dealer. Front Fog Lamps Indicator


It will illuminate when you switch the front fog lamps on.


WARNING


Headlamp Indicator


It will illuminate when you switch the headlamp dipped beam or the side and tail lamps on.


High Beam Indicator


It will illuminate when you switch the high beam headlamps on. It will flash when you use the


headlamp flasher. Ignition Warning Lamp


If it illuminates when you are driving, this indicates a malfunction.


Switch off all unnecessary electrical equipment. Have your vehicle checked by an authorized dealer immediately.


Do not resume your journey if it illuminates despite the level being correct. Have your vehicle checked


by a an authorized dealer immediately.


If it stays on after starting or illuminates when driving, this indicates a malfunction.


Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the coolant level. See Engine Coolant Check (page 183). Engine Oil Warning Lamp


WARNING


Do not resume your journey if it illuminates despite the level being correct. Have your vehicle checked


by an authorized dealer immediately.


If it illuminates with the engine running or when you are driving, this indicates a malfunction.


77


Fiesta (CCT), enUSA, Second Printing


Instrument Cluster


If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.


WARNING


Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic


converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Have an authorized dealer service your vehicle immediately.


The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 119). Shift Indicator


It will illuminate to inform you that shifting to a higher gear may give better fuel economy and


lower CO2 emissions. It will not illuminate during periods of high acceleration, braking or when the clutch pedal is pressed.


Information Indicator


It will illuminate when a new message is stored in the information and entertainment


display. See Information Messages (page 87). Low Fuel Level Warning Lamp


If it illuminates, refuel as soon as possible.


Low Tire Pressure Warning


It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check


your tire pressure as soon as possible. It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have your vehicle checked by an authorized dealer. Safety Belt Minder Warning Lamp It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety


Belt Minder (page 30). Service Engine Soon


If the service engine soon indicator light stays illuminated after the engine is started, it


indicates that the On-Board Diagnostics (OBD-II) system has detected a malfunction of the vehicle emissions control system. Refer to On-Board Diagnostics (OBD-II) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 119).


78


Fiesta (CCT), enUSA, Second Printing


Instrument Cluster


Stability Control Indicator


While driving, it flashes when the system is operating. After you switch the ignition on, if it does not illuminate or illuminates continuously while driving, this indicates a malfunction. During a malfunction, the system switches off. Have your vehicle checked by an authorized dealer as soon as possible. Stability Control System Off Indicator


It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off.


WARNING LAMPS AND INDICATORS - 1.6L ECOBOOST™ The following warning lamps and indicators alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not illuminate when you start your vehicle. Anti-lock Braking System Warning Lamp


If it illuminates when you are driving, this indicates a malfunction.


You will continue to have the normal braking system (without anti-lock braking system) unless the brake system warning lamp is also illuminated. Have your vehicle checked by an authorized dealer. Brake System Warning Lamp


It illuminates when you engage the parking brake and the ignition is on. If it illuminates


when your vehicle is moving, make sure the parking brake is disengaged. If the parking brake is disengaged, this indicates low brake fluid level or a brake system fault. Have your vehicle checked immediately by an authorized dealer.


WARNING


Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control Indicator


It will illuminate when you switch this feature on. See Using Cruise Control (page 139).


Direction Indicator


Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the


indicators stay on or flash faster, check for a burnt out bulb. See Changing a Bulb (page 194).


79


Fiesta (CCT), enUSA, Second Printing


E138644E71340 Instrument Cluster


Door Ajar Warning Lamp


Illuminates when you switch the ignition on and remains on if any door, the hood or the liftgate is


not closed properly. Engine Coolant Temperature Warning Lamp


WARNING


Do not resume your journey if it illuminates despite the level being correct. Have your vehicle checked


by a an authorized dealer immediately.


If it stays on after starting or illuminates when driving, this indicates a malfunction.


Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the coolant level. See Engine Coolant Check (page 183). Engine Oil Warning Lamp


WARNING


Do not resume your journey if it illuminates despite the level being correct. Have your vehicle checked


by an authorized dealer immediately.


If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Coolant Check (page 183).


Front Airbag Warning Lamp


If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have your vehicle checked by an authorized dealer. Front Fog Lamps Indicator


It will illuminate when you switch the front fog lamps on.


Headlamp Indicator


It will illuminate when you switch the headlamp dipped beam or the side and tail lamps on.


High Beam Indicator


It will illuminate when you switch the high beam headlamps on. It will flash when you use the


headlamp flasher. Ignition Warning Lamp


If it illuminates when you are driving, this indicates a malfunction.


Switch off all unnecessary electrical equipment. Have your vehicle checked by an authorized dealer immediately. Information Indicator


It will illuminate when a new message is stored in the information and entertainment


display. See Information Messages (page 87).


80


Fiesta (CCT), enUSA, Second Printing


Instrument Cluster


WARNING


Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic


converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Have an authorized dealer service your vehicle immediately.


The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 119). Shift Indicator


It will illuminate to inform you that shifting to a higher gear may give better fuel economy and


lower CO2 emissions. It will not illuminate during periods of high acceleration, braking or when the clutch pedal is pressed. Stability Control Indicator


While driving, it flashes when the system is operating. After you switch the ignition on, if it does not illuminate or illuminates continuously while driving, this indicates a malfunction. During a malfunction, the system switches off. Have your vehicle checked by an authorized dealer as soon as possible.


Low Fuel Level Warning Lamp


If it illuminates, refuel as soon as possible.


Low Tire Pressure Warning


It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check


your tire pressure as soon as possible. It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have your vehicle checked by an authorized dealer. Safety Belt Minder Warning Lamp It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety


Belt Minder (page 30). Service Engine Soon


If the service engine soon indicator light stays illuminated after the engine is started, it


indicates that the On-Board Diagnostics (OBD-II) system has detected a malfunction of the vehicle emissions control system. Refer to On-Board Diagnostics (OBD-II) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 119). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.


81


Fiesta (CCT), enUSA, Second Printing


Instrument Cluster


Parking Brake On Sounds when the parking brake is on and your vehicle is moving. If the warning chime continues to sound when you release the parking brake, have the system checked by an authorized dealer. Safety Belt Minder


WARNINGS


The safety belt minder remains in stand-by mode when the front safety belts have been fastened. It will


sound if either safety belt is unfastened.


Do not sit on top of a fastened safety belt to prevent the safety belt minder from coming on. The occupant


protection system will only provide optimum protection when you use the safety belt correctly.


Sounds when your vehicle speed exceeds the pre-determined limit and the front safety belts are unfastened. The chime will stop after a period of time.


Stability Control System Off Indicator


It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off.


AUDIBLE WARNINGS AND INDICATORS Exterior Lamps On Sounds when you remove the key from the ignition and open the driver door, and you have left the headlamps or parking lamps on. Gearshift Lever Not in Park (P) Sounds when the driver door is open, the key is in the ignition and the gearshift lever is not in park (P). Key in Ignition Sounds when the driver door is open and the key is in the ignition. Key Outside Vehicle - Vehicles With Keyless System Sounds when you close the driver door, the key is outside your vehicle and and the engine is running. The system does not detect a passive key inside your vehicle. Low Fuel Sounds when the remaining fuel is less than approximately 1.6 gal (6 L). The distance to empty displayed may vary depending on driving style and road conditions.


82


Fiesta (CCT), enUSA, Second Printing


Information Displays


GENERAL INFORMATION


Information Display Controls


WARNING


Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.


Note: The information display will remain on for several minutes after you switch the ignition off. Device List The icon changes to show the current function in use.


CD


Radio


Auxiliary input


83


Fiesta (CCT), enUSA, Second Printing


Various systems on your vehicle can be controlled using the information display controls on your audio unit. Corresponding information is displayed in the information display. To use the controls: • Press the up or down arrow button to scroll through and highlight the options within a menu.


• Press the right arrow button to enter a


submenu.


• Press the left arrow button to exit a


submenu.


• Press and hold the left arrow button at


any time to return to the main menu display.


• Press the OK button to choose and


confirm settings or messages.


Menu Structure - Information Display You can access the menu using the information display control. Note: Some options may appear slightly different or not at all if the items are optional. SYNC-Media allows you to access the SYNC® features.


E103626 Information Displays


SYNC-Phone


Dial a number Redial Phonebook Call history Speed Dial Text messaging BT Devices Phone settings


Ford EcoMode SYNC-Settings


SYNC-Apps Navigation


Audio settings


Fiesta (CCT), enUSA, Second Printing


Menu


Bluetooth on Set defaults Master reset Install on SYNC System info Voice settings


Route options Map display Assistance options Personal data Reset all settings Adaptive volume Sound NAV audio mixing


84


Information Displays


Menu


DSP settings DSP equalizer Traffic News Alt. frequency RDS Regional Traction Control Hill start assist Alarm system Powerfold mirrors Indicator Ambient light Chimes Auto time (GPS) Set time Set date Set time zone 24-hour mode Measure Unit Language Dimming create MyKey Traction control ESC Speed limit Speed warning Volume limit


85


Vehicle settings


Clock settings


Display settings


MyKey


Fiesta (CCT), enUSA, Second Printing


Information Displays


Menu


Information clear all MyKeys Information


MyKey active


1. Scroll to the required display. 2. Press and hold the button to reset the


trip computer.


The Trip Computer Includes the Following Information Displays Trip Odometer


Records the distance traveled on individual journeys.


Distance to Empty


Indicates the approximate distance your vehicle will travel on the fuel remaining in the tank. The distance to empty displayed may vary depending on driving style and road conditions.


Average Fuel Consumption


Indicates the average fuel consumption since the function was last reset.


Average Speed


Indicates the average speed since the function was last reset.


System Check All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Press the up or down arrow button to scroll through the list. CLOCK Type 1
To adjust the clock, switch the ignition on and press buttons H or M on the information and entertainment display as necessary. Type 2
Note: Use the information display to adjust the clock. See (page 83). TRIP COMPUTER (If Equipped)


Press the button to scroll through the displays. You can reset the trip odometer, average fuel consumption and average speed.


86


Fiesta (CCT), enUSA, Second Printing


E102759E164638EE146275E146277 Information Displays


Distance Odometer


Records the total distance traveled by your vehicle.


INFORMATION MESSAGES Note: Depending on the options on your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have.


PERSONALIZED SETTINGS Measure Units To swap between imperial and metric units, scroll to this display and press the OK button. Swapping between imperial and metric units will affect the following displays: • Distance to empty. • Average fuel consumption. • • Average speed. Switching Chimes Off To switch chimes off, scroll to this display and press the OK button. The following chimes can be switched off: • Warning messages. •


Instantaneous fuel consumption.


Information messages.


Press the OK button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time. Certain messages need to be confirmed before you can access the menus. The message indicator illuminates to supplement some messages. It will be red or amber depending on the severity of the message and will remain on until the cause of the message has been rectified. Some messages will be supplemented by a system specific symbol with a message indicator.


Airbag


Message


Message indicator


Action


Airbag malfunction Service now


Amber


Have the system checked by an authorized dealer as soon as possible.


87


Fiesta (CCT), enUSA, Second Printing


E103626 Information Displays


Action


See Security (page 58). See Security (page 58). Have the system checked by an authorized dealer.


Action


Vehicle is moving. Stop your vehicle as soon as safely possible and close. Vehicle is moving. Stop your vehicle as soon as safely possible and close. Vehicle is moving. Stop your vehicle as soon as safely possible and close. Vehicle is moving. Stop your vehicle as soon as safely possible and close. Vehicle is moving. Stop your vehicle as soon as safely possible and close. Vehicle is moving. Stop your vehicle as soon as safely possible and close. See Opening and Closing the Hood (page 177). Vehicle not moving. Close. Vehicle not moving. Close. Vehicle not moving. Close.


Alarm


Message


Alarm triggered Check vehicle Interior scan deactivated Alarm system malfunction Service required


Doors Open


Message


Driver door open


Driver side rear door open


Passenger door open


Passenger side rear door open


Trunk open


Hood open


Driver door open Driver side rear door open Passenger door open


Fiesta (CCT), enUSA, Second Printing


Message indicator Amber Amber


Message indicator


Red


Red


Red


Red


Red


Red


Amber Amber Amber


88


Information Displays


Action


Vehicle not moving. Close. Vehicle not moving. Close. Vehicle not moving. Close. See Opening and Closing the Hood (page 177).


Action


Have the system checked by an authorized dealer as soon as possible.


Action


See Hill Start Assist (page 128).


Action


See Keyless Entry (page 55). See Keyless Entry (page 55). See Remote Control (page 42). See Keyless Starting (page 111). See Keyless Starting (page 111). See Keyless Starting (page 111). See Keyless Entry (page 55).


Message


Passenger side rear door open Trunk open


Hood open


Engine Immobilizer


Message


Immobilizer malfunction Service now


Hill Start Assist


Message


Hill start assist not available


Keyless System


Message


Key not detected Key outside car Key Battery low Replace battery Switch ign. off Press ENGINE Start/ Stop button Press brake to start Press clutch to start Close trunk or use spare key


Fiesta (CCT), enUSA, Second Printing


Message indicator Amber Amber


Amber


Message indicator


Red


Message indicator Amber


Message indicator Amber Amber Amber


Amber


89


Information Displays


Lighting


Message


Message indicator


Action


Left indicator malfunction Change bulb Right indicator malfunction Change bulb


See Changing a Bulb (page 194).


See Changing a Bulb (page 194).


Action


See Brake Fluid Check (page 186). Have the system checked by an authorized dealer immediately. See Engine Oil Check (page 182). Have the system checked by an authorized dealer as soon as possible. Have the system checked by an authorized dealer. Your vehicle is still in transport mode or factory mode. Some features may not be available. See an authorized dealer.


Maintenance


Message


Brake fluid level low Service now Brake system malfunction Stop safely Engine oil pressure low Stop safely


Message indicator


Red


Red


Red


Engine malfunction Service now


Amber


Engine oil change due Service required


Paused


Fiesta (CCT), enUSA, Second Printing


90


Information Displays


MyKey


Message


Message indicator


Action


MyKey Vehicle at top speed


Amber


MyKey active Drive safely


MyKey Speed limited to mph


MyKey Speed limited to km/


MyKey check speed Drive safely


MyKey vehicle near top speed


MyKey Buckle up to unmute audio


MyKey Park aid cannot be deactiv- ated


MyKey ESC cannot be deactivated


Displays when a MyKey is in use and the MyKey speed limit is on and your vehicle speed is approaching 80
mph (130 km/h). Displays when MyKey is active. Displays when starting your vehicle and MyKey is in use and the MyKey speed limit is on. Displays when starting your vehicle and MyKey is in use and the MyKey speed limit is on. Displays when MyKey is active. Displays when a MyKey is in use and the MyKey speed limit is reached. Displays when a MyKey is in use and Belt- Minder is activated. Displays when a MyKey is in use and park aid is activated. Displays when programming a MyKey.


Parking Brake


Message


Park brake applied Park brake applied


Message indicator


Red Amber


Action


See Parking Brake (page 131). See Parking Brake (page 131).


91


Fiesta (CCT), enUSA, Second Printing


Information Displays


Stability Control


Message


Electronic stability control off


Message indicator


Amber


ABS malfunction Service Now


Amber


Traction control off


Sport mode


Electronic stability control off


Action


See Using Stability Control (page 134). Have the system checked by an authorized dealer as soon as possible. See Using Stability Control (page 134). See Using Stability Control (page 134). See Using Stability Control (page 134).


Starting and Stopping the Engine


Message


Message indicator


Action


Press brake to start


Press clutch to start


Press brake and clutch to start


Cranking time exceeded


Steering


Message


Steering assist fault Service required


Fiesta (CCT), enUSA, Second Printing


See Starting and Stopping the Engine (page 111). See Starting and Stopping the Engine (page 111). See Starting and Stopping the Engine (page 111). See Starting and Stopping the Engine (page 111).


Action


Full steering will be maintained but you will need to exert greater force on the steering wheel. Have the system checked by an authorized dealer as soon as possible.


Message indicator


Amber


92


Information Displays


Tire pressure monitoring system


Message


Check tire pressures


Message indicator


Amber


Tire Pressure Monitor Fault


Amber


Transmission


Message


Transmission malfunction Service now


Message indicator


Red


Transmission overtemperature Stop safely


Red


Use brake Stop safely


Red


Vehicle not in Park Select P


Select N or P to start


Press brake to start


Fiesta (CCT), enUSA, Second Printing


93


Action


The pressure in one or more tires has dropped. Check as soon as possible. Permanent malfunction. Have your vehicle checked by an authorized dealer.


Action


Have the system checked by an authorized dealer immediately. Under certain driving conditions it is possible that the clutches in the transmission can overheat. In these circumstances it is necessary to press the brake pedal and stop your vehicle to prevent damage to the transmission. Move the transmis- sion selector lever to position N or P and apply the parking brake until the transmission has cooled and the message disappears from the display. Have the system checked by an authorized dealer immediately. See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111). See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111). See Starting and Stopping the Engine (page 111).


Information Displays


Message


Message indicator


Action


See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111). See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111). Transmission is getting hot. Stop to let it cool or speed up. Transmission is hot. Wait as needed to let it cool. Your vehicle is ready to drive. See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111). See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111). See Automatic Transmission (page 124). See Starting and Stopping the Engine (page 111).


Select N to start


Door open Apply brake


Transmission hot Stop or speed up


Transmission hot Wait...


Transmission ready


Press brake to unlock gearshift lever


Gearshift lever unlocked


Transmission not in Park


Fiesta (CCT), enUSA, Second Printing


94


Climate Control


Air Conditioning The system directs air through the evaporator for cooling. The evaporator extracts humidity from the air to help keep the windows free of mist. The system directs the resulting condensation to the outside of your vehicle, which may cause a small pool to form under your vehicle. This is normal. Note: The air conditioning operates only when the temperature is above 39°F (4°C). Note: When you use air conditioning, your vehicle uses more fuel. AIR VENTS Center Air Vents


Side Air Vent


PRINCIPLE OF OPERATION Outside Air Keep the air intakes in front of the windshield free from obstruction (such as snow or leaves) to allow the climate control system to function effectively. Recirculated Air


WARNING


Prolonged use of recirculated air may cause the windows to mist up. If the windows mist up, follow the settings


for demisting the windshield.


The air currently in the passenger compartment recirculates. Outside air does not enter your vehicle. Heating Heating performance depends on the temperature of the engine coolant. General Information on Controlling the Interior Climate Fully close all the windows. Warming the Interior Direct the air toward your feet. In cold or humid weather conditions, direct some of the air toward the windshield and the door windows. Cooling the Interior Direct the air toward your face.


95


Fiesta (CCT), enUSA, Second Printing


E147812E71942 Climate Control


MANUAL CLIMATE CONTROL


Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed. Air distribution control: Adjust to select the desired air distribution. If you select MAX A/C the system distributes recirculated air through the instrument panel air vents. This mode is more economical and efficient than normal air conditioning. Select O to turn the system off. Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the button illuminates and the air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. Temperature control: Controls the temperature of the air circulated in your vehicle. Adjust to select the desired temperature. Heated rear window: Press the button to defog and clear the rear window of a thin covering of ice. Air conditioning: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve air conditioning when starting your vehicle, drive with the windows slightly open for two to three minutes.


96


Fiesta (CCT), enUSA, Second Printing


ABCDFEE158234 Climate Control


AUTOMATIC CLIMATE CONTROL (If Equipped)


Fan speed: Controls the volume of air circulated in your vehicle. Rotate the control to select the desired fan speed. The setting is shown in the display. Instrument panel: Press the button to distribute air through the instrument panel air vents. Defrost: Press the button to distribute air through the windshield air vents. You can also use this setting to defog and clear the windshield of a thin covering of ice. MAX Defrost: Press the button to distribute outside air through the windshield air vents. Air conditioning is automatically selected. The fan is set to the highest speed and the temperature to HI. When the air distribution is set in this position, you are unable to select recirculated air or manually adjust the fan speed and temperature control. Press the AUTO button to return to auto mode. MAX A/C: Press the button to distribute recirculated air through the instrument panel air vents. This mode is more economical and efficient than normal air conditioning. Temperature control: Controls the temperature of the air circulated in your vehicle. Adjust to select the desired temperature.


97


Fiesta (CCT), enUSA, Second Printing


ABCFDELKHIJGE158263 Climate Control


Air conditioning: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve air conditioning when starting your vehicle, drive with the windows slightly open for two to three minutes. Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. OFF: Press the button to switch the system off. Heated rear window: Press the button to defog and clear the rear window of a thin covering of ice. Footwell: Press the button to distribute air through the footwell air vents. AUTO: Press the button to switch the system on and off. The system automatically controls the temperature, amount and distribution of the airflow to reach and maintain your previously selected temperature.


HINTS ON CONTROLLING THE INTERIOR CLIMATE General Hints Note: Prolonged use of recirculated air may cause the windows to fog up. Note: A small amount of air may be felt from the footwell air vents regardless of the air distribution setting. Note: To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on. Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Note: Remove any snow, ice or leaves from the air intake area at the base of the windshield.


Temperature Control


You can set the temperature between 61°F (16°C) and 82°F (28°C). In position low, the system switches to permanent cooling. In position high, the system switches to permanent heating. Note: If you select either position low or high, the system will not regulate a stable temperature.


98


Fiesta (CCT), enUSA, Second Printing


E148690 Climate Control


Manual Climate Control Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position. Increase the temperature and fan speed to improve clearing, if required. Automatic Climate Control Note: Do not adjust the settings when your vehicle interior is extremely hot or cold. The system automatically adjusts to the previously stored settings. For the system to function efficiently, the instrument panel and side air vents should be fully open. Note: At low ambient temperatures with AUTO selected, the air stream is directed toward the windshield and side windows for as long as the engine remains cold. Heating the Interior Quickly


Note: When the system is switched off, outside air is prevented from entering your vehicle. Note: When you select AUTO mode and the interior and exterior temperatures are high, the system automatically selects recirculated air to maximize cooling of the interior. When the desired air temperature is reached, the system automatically selects outside air. Note: When you select windshield defrosting and defogging, the instrument panel and footwell level functions automatically switch off and air conditioning switches on. Outside air flows into your vehicle.


Vehicles With Manual Climate Control

Loading...
x