2012 Ford F 350 Owners Manual

identification lamps (3) LED** *Rear fender clearance *Rear identification 193** To replace all instrument panel lights - see your authorized dealer * Dual rear wheels, or if equipped. ** See your authorized dealer to replace the lamp assembly.

921
3157
912
9145
194
912

578
194
2825
2825
194

12V6W

93

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Lights

Replacing headlamps, park lamps, turn lamps 1. Make sure that the exterior lamps are off, then open the hood. 2. Using masking tape or a marker, make an alignment mark between one of the grille brackets and the vehicle radiator support to ensure correct grille alignment during re-assembly. Do not scratch the black coating from the radiator support. 3. Remove the two grille to headlamp assembly push pins and the four bolts attaching the top of the grille to the radiator support. 4. Pull the top of the grille forward to gain access to the lower grille spring clips. 5. Depress the spring clips through the lower inner grille access openings using a flat head screwdriver. 6. Pull the grill straight out to remove. 7. Remove the four bolts from the headlamp assembly. 8. Pull the assembly straight out disengaging one snap clip from the fender. 9. Disconnect the electrical connector by squeezing the release tab and pushing the connector forward, then pulling it rearward.

94

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Lights

10. For the headlamp bulb, remove the bulb by turning it counterclockwise and pulling it straight out.

11. For the park or turn lamp bulb, remove the bulb by turning it counterclockwise and pulling it straight out.

WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Install the new bulb(s) in reverse order. Replacing brake/tail/turn/back-up lamp bulbs (pick-ups only) 1. Make sure the headlamps are off, then open the tailgate to expose the lamp assemblies. 2. Remove the two bolts from the tail lamp assembly and carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs.

95

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Lights

3. Rotate the bulb socket counterclockwise and remove from lamp assembly. 4. Pull the bulb straight out of the socket. Install the new bulb(s) in reverse order. Replacing brake/tail/turn/back-up lamp bulbs (chassis cabs only) (if equipped) 1. Make sure the headlamps are off. 2. Remove the four screws and the lamp lens from lamp assembly. 3. Carefully pull the bulb straight out of the socket and push in the new bulb.

Replacing cargo lamp and high-mount brake lamp bulbs 1. Make sure the headlamps are off. 2. Remove the screws and lamp assembly from the vehicle as wiring permits. 3. Remove the bulb socket by rotating it counterclockwise. 4. Pull the bulb straight out of the socket.

96

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Lights

Replacing front clearance and identification lamp bulbs (if equipped) 1. Make sure the headlamps are off. 2. Remove the screw and lens from the lamp assembly. 3. Pull the bulb straight out of the socket.

Install the bulb(s) in reverse order. Replacing fog lamp bulbs (if equipped) 1. Make sure the headlamps are off. 2. Remove the bulb socket from the fog lamp by turning it counterclockwise. 3. Disconnect the electrical connector from the fog lamp bulb.

Install the new bulb(s) in reverse order. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. 3. Pull out the old bulb from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly by turning it clockwise.

97

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically adjust with the vehicle speed. The faster your vehicle is travelling the faster the wipers will go. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick press and hold: the

wipers will swipe three times with washer fluid.

• a long press and hold: the wipers and washer fluid will be activated for

up to 10 seconds.

Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining on the windshield. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluid level frequently. Do not operate the wipers when the windshield is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield, always use the windshield washer. In freezing weather, be sure the wiper blades are not frozen to the windshield before operating the wipers.

Windshield wiper rainlamp feature (if equipped with autolamp) When the windshield wipers are turned on during daylight, and the headlamp control is in the autolamp position, the exterior lamps will turn on after a brief delay and will remain on until the wipers are turned off. 98

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock the steering column. 2. While the lever is in the down position, move the steering wheel up or down and in or out until you find the desired position. 3. While holding the steering wheel in place, pull the lever up to its original position to lock the steering column.

WARNING: Never adjust the steering wheel when the vehicle is moving.

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps.

Slide-on-rod feature (if equipped) Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

99

Driver Controls

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.

Storage compartment (if equipped) Press the release tab on the rear edge of the bin door to open the storage compartment. The door will open to the full open position. The storage compartment may be used to secure sunglasses or a similar object.

with hanging file folder supports

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • Locking storage compartment • Storage for laptop computer, binder or book between the hanging file folder support and the passenger side of the console bin • One 12V power point inside the storage compartment and one on the rear of the console

• 110V AC power point outlet on the rear of the console • Rear cupholders

100

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

modules

• Two removable front cupholder • Removable false bottom tray for accessing hidden storage compartment (also has space for a large cup)

WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision.

AUXILIARY POWER POINT (12V DC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet for this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. Auxiliary power points can be found in the following locations: • On the instrument panel (two locations) • Inside the center console storage compartment (if equipped) • On the rear of the center console (if equipped) • Inside the 20-percent front seat console (if equipped) • Inside the rear under seat storage compartment (if equipped) Do not use the power point for operating the cigarette lighter element (if equipped). Note: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12V DC/180W. If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses.

101

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

To have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery. To prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is • do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods.

not running,

Always keep the power point caps closed when not being used.

AC 110V

Power point (110V AC) (if equipped) The 110V AC power point outlet is used for powering electrical devices that require up to 150W. Exceeding the 150W limit will cause the power point to cut off the power temporarily to provide overload protection. Note: The 110V AC power point is equipped with a cap which provides protection from inserting objects into the socket. The cap should always be in a closed position whenever the power point outlet is not in use. The 110V AC power point is located on the back of the center console. The power outlet is not designed for the following electric appliances; they may not work properly: • Cathode ray tube type televisions • Motor loads, such as vacuum cleaners, electric saws and other electric • Measuring devices, which process precise data, such as medical • Other appliances requiring an extremely stable power supply:

power tools, compressor-driven refrigerators, etc.

equipment, measuring equipment, etc.

150W

microcomputer-controlled electric blankets, touch sensor lamps, etc.

WARNING: Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any

extension cord with the 110V AC power point, since it will defeat the safety protection design provided by the cap and twist tab. Doing so my cause the power point to overload due to powering multiple devices that can reach beyond the 150W load limit and could result in fire or serious injury.

102

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

The power point can switch to a fault mode when it is overloaded, overheated, or shorted. For overloading and shorting conditions, unplug your device and turn the ignition key off then on. For an overheating condition, let the system cool off, then turn the ignition key off then on. The 110V AC power point can provide power whenever the vehicle ignition is in the on position and the power point green indicator light located in the top left corner is turned on. Refer to the indicator light code below for the power point status.

Indicator light codes

Green light is on — Power point is ready to supply power Green light is off — Power point power supply is off. Ignition is not in the on position Green light is blinking — Power point is in fault mode Note: The 110V AC power point will turn off after 13 minutes if the ignition is in the on position without the engine running. Keep the engine running or cycle the ignition before the 13 minute time-out to keep the inverter on.

POWER WINDOWS (IF EQUIPPED)

WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may

seriously injure themselves.

WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or

pets are not in the proximity of the window openings.

Press and pull the window switches to open and close windows. • Press down (to the first detent) • Pull up (to the first detent) and

and hold the switch to open.

hold the switch to close.

Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviated by lowering a front window approximately 2–3 in. (5–8 cm).

103

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

One-touch down Allows the driver’s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation. Window lock (if equipped) The window lock feature allows only the driver to operate the power windows. To lock out all the window controls (except for the driver’s) press the right side of the control. Press the left side to restore the window controls. Power sliding back window (if equipped) The control is located on the overhead console. Press and hold the open the window all the way to the full open position. Pull and hold the close the window.

control to

control to

WARNING: When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the

proximity of the back window.

WARNING: Do not leave children unattended in the vehicle and do not let children play with the power sliding back window.

They may seriously injure themselves.

Accessory delay With accessory delay, the window switches may be used for up to 10 minutes after the ignition switch is turned to the off position or until either front door is opened. 104

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

INTERIOR MIRROR The interior rearview mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side.

WARNING: Do not adjust the mirror while the vehicle is in motion.

Automatic dimming interior rear view mirror (if equipped) The interior rear view mirror has an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Note: A rear center passenger and/or raised rear center headrest (if equipped) may also block the light from reaching the sensor. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a rearview camera system, a video image will display in the mirror or the navigation system display (if equipped) when the vehicle is put in R (Reverse). As you shift into any other gear from R (Reverse), the image will remain for a few seconds and then turn off. Refer to Rearview camera system in the Driving chapter.

105

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

EXTERIOR MIRRORS

Power side view mirrors (if equipped)

WARNING: Do not adjust the mirror while the vehicle is in motion.

To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. The spotter mirror below the main glass (if equipped) must be adjusted manually.

located on the

(if equipped)

Heated outside mirrors The main mirror glass and lower convex spotter mirror are heated to remove ice, mist and fog. To activate the heated mirrors, press the heated mirror control climate control panel. Do not remove ice from the mirrors with a scraper or attempt to re-adjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

106

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

Fold-away mirrors Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. Power-fold mirrors (if equipped) You can fold the side mirrors simultaneously using the power mirror switch.

To operate the power-fold mirrors: 1. Rotate the switch to the center/neutral position. 2. Momentarily pull the switch rearward to auto fold in. 3. Momentarily pull the switch rearward again to fold back to design position. Note: When power-folding the mirrors, it is normal to hear the sound of the motors.

Power-fold mirror positions, from left to right: Position 1, Position 2, Position 3
The power-fold mirrors may be folded forward/rearward manually to any of the three positions shown and electrically to positions 1 and 2 only. If a mirror is folded manually forward to position 3, you must manually fold it back to position 1 or 2 in order for the power-fold function to continue functioning. Note: Although it is possible to electrically fold the mirror from position 3 to 2, it was not designed for this functionality and may not always work under all conditions.

107

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

Note: Ten or more switch activations within one minute, or repeated fold/unfolding of the mirrors while holding the switch rearward during the full travel may cause the system to disable the fold/unfold function to protect the motors from overheating. Should this occur, wait approximately 31⁄2 minutes for the system to reset and function to return to normal. Note: The power-fold mirrors are designed to operate while the vehicle is stationary or traveling at moderate speeds. If you attempt to power-fold the mirrors at high speeds, they may not fully fold forward/rearward - slow down and power-fold or manually fold the mirrors in order to complete the fold operation. Note: If the power fold/telescope mirror glass appears loose or vibrates when driving, it is possible that the mirrors have been manually folded or telescoped. To minimize the vibration, ensure that the mirrors are electronically folded and telescoped in/out with the switches on the door trim panel. If the power fold mirrors are out of sync, electronically power-fold the mirrors to re-sync the motors. This will cause a loud “click” and the mirrors will jerk during re-synchronization. This is normal.

Telescoping mirrors (if equipped) The telescoping feature allows the mirror to extend approximately 2.75 inches (70 mm). This feature is especially useful to the driver when towing a trailer. Mirrors can be manually pulled out or pushed in to the desired telescopic position.

If equipped with PowerScope™ power telescoping mirrors, you can simultaneously position both mirrors using the power telescope switch found on the door trim panel. • To telescope the mirrors

outboard, press and hold the left side of the power telescope switch until the mirrors reach their desired position. When the end of travel is reached, it is normal to hear the power telescoping motors running as long as you continue to hold the switch.

108

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls • To telescope the mirrors inboard, press and hold the right side of the power telescope switch until the mirrors reach their desired position.

Memory mirrors (if equipped) This system allows automatic positioning of the outside rearview mirrors. For more information on this feature, refer to Memory seats/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter.

Mirror-mounted side turn signal indicator (if equipped) When the vehicle turn signals are activated, the outer portion of the mirror housing will blink amber. The turn signal feature can be seen by other drivers who may approach from the rear of the vehicle.

Clearance lamps (if equipped) Illuminates when the headlamps or parking lamps are switched on. This provides additional visibility of your vehicle to other drivers on the road.

109

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. The control is located on the left side of the steering column. Press and hold the rear of the control to move the pedals toward you. Press and hold the front of the control to move the pedals away from you.

WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

The accelerator and brake pedal positions are saved when doing a memory set function and can be recalled along with the vehicle personality features when a memory position is selected. Refer to Memory seats/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.

WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Using speed control The speed controls are located on the steering wheel.

110

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

CNCL (Cancel)/RSM (Resume): Press to cancel or resume a set speed. ON/OFF: Press to turn the system on or off. – SET +: Press to set a speed or to decrease or increase a set speed.

Driver Controls

C N C L R S M

O N / O F F

- S E T +

indicator lights in the instrument The speed control system uses two cluster: • an amber indicator light which illuminates when the system is on, and • a green indicator light which illuminates when the system is engaged. Setting speed control To set speed control: 1. Press and release ON. 2. Accelerate to the desired speed. 3. Press and release SET +. 4. Take your foot off the accelerator pedal. 5. The green indicator light Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

on the instrument cluster will turn on.

steep hill.

your set speed on an uphill, your speed control will disengage.

Disengaging a set speed To disengage speed control, tap the brake pedal or press and release CNCL. Disengaging the speed control will not erase the previous set speed. Resuming a set speed Press and release RSM. This will automatically return the vehicle to the previously set speed.

111

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

Increasing speed while using speed control To increase the set speed: • Press and hold SET + until you get to the desired speed, then release.

You can also use SET + to operate the tap-up function. Press and release SET + to increase the vehicle set speed in approximately 1 mph (2 km/h) increments.

• Use the accelerator pedal to get to the desired speed then press and

release SET +.

Reducing speed while using speed control To reduce a set speed: • Press and hold SET – until you get to the desired speed, then release. You can also use SET – to operate the tap-down function. Press and release SET – to decrease the vehicle set speed in approximately 1 mph (2 km/h) increments.

• Press the brake pedal until the desired vehicle speed is reached then

press and release SET +. Turning off speed control To turn off the speed control, press OFF or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Audio control features MEDIA: Press repeatedly to scroll through available audio modes.

SEEK

: Press to select

the previous/next radio station preset or CD track (if equipped). Press and hold to select the previous/next radio station frequency or to reverse/forward a CD. + VOL – (Volume): Press to increase or decrease the volume. 112

MEDIA

SEEK

VOL

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

icon appears on the

icon appears on the display

Navigation system hands free control features (if equipped) Press and hold VOICE briefly until the voice navigation display to use the voice command feature. Press VOICE to complete a voice command. For further information on the Navigation system, refer to the Navigation System supplement. SYNC威 system hands free control feature (if equipped) Press VOICE briefly until the voice to use the voice command feature. You will hear a tone and LISTENING will appear in the radio display. Press and hold VOICE to exit voice command. to activate phone mode or Press answer a phone call. Press and hold Press OK to confirm your selection. For further information on the SYNC威 system, refer to the SYNC威 supplement. Navigation system/SYNC威 hands free control features (if equipped) Press VOICE briefly until the icon appears on the voice navigation display to use the voice command feature. Press answer a phone call. Press and hold call.

to exit phone mode or end

to activate phone mode or

to end call or exit phone mode. to scroll through various menus and selections. Press

113

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

For further information on the Navigation system/SYNC威 system, refer to the Navigation System and SYNC威 supplements.

UPFITTER CONTROLS (IF EQUIPPED) Your vehicle may be equipped with the Upfitter option package which will provide four switches, mounted in the center of the instrument panel, labeled AUX 1, AUX 2, AUX 3
and AUX 4. These switches will only operate while the ignition is in the on position, whether the engine is running or not. It is, however, recommended that the engine remain running to maintain battery charge when using the Upfitter switches for extended duration or higher current draws. (This is even more important for vehicles with diesel engines since the glow plugs are also draining battery power when the ignition key is in the on position.) When switched on by the operator they provide 8 amps, 12 amps or 20 amps of electrical battery power for a variety of personal or commercial uses. If your vehicle is equipped with this option, there will also be a relay box located on the driver side end of the instrument panel. See your authorized dealer for service. The relays are coded as shown in the accompanying illustration.

RELAY

RELAY

RELAY

RELAY

114

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

There will also be one power lead for each switch found as a blunt-cut and sealed wire located below the instrument panel and to the left of the steering column.

They are coded as follows:

Switch

Circuit number Wire color

AUX 1
AUX 2

AUX 3

CAC05
CAC06

CAC07

Yellow Green with Brown Trace Violet with Green Trace Brown

Fuse 25A 25A

10A

AUX 4
15A More detailed information about Upfitter switches can be found at https://www.fleet.ford.com/truckbbas/.

CAC08

MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console.

WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt

themselves.

WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are

not in the proximity of the moon roof opening.

The moon roof is equipped with an automatic, one-touch, express opening and closing feature. To stop motion at any time during the one-touch operation, press the control a second time.

115

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

To open the moon roof: Press and release the SLIDE control and the moon roof will open automatically to the “comfort” position. Press and release again to fully open. Press the switch again to stop the moon roof. To close the moon roof: Pull and release the SLIDE control, the moon roof will close automatically. Press the switch again to stop the moon roof. Bounce-back: When an obstacle has been detected in the moon roof opening as the moon roof is closing, the moon roof will automatically open and stop at a prescribed position. Bounce-back override: To override bounce-back function, pull and hold the SLIDE switch within two seconds of a bounce-back event. The closing force will begin to increase each time the moon roof is closed for the first three closing cycles, with bounce-back active. For example: Bounce-back can be used to overcome the resistance of ice on the moon roof or seals To vent the moon roof: Press and release the TILT control, the moon roof will move to the vent position automatically from any moon roof position. Press the switch again to stop the moon roof. Pull and hold the TILT control to close the moon roof. The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle.

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) Your vehicle may be equipped with a universal garage door opener which can be used to replace the common hand-held transmitter.

WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not

program the system with the vehicle in the garage.

WARNING: Do not use the system with any garage door opener that does not have the safety stop and reverse feature as

required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).

116

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. Note: We recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the function button codes later in this section. Note: You can program a maximum of three devices. To change or replace any of the three devices after it has been initially programmed, you must first erase the current settings. See Erasing the function button codes later in this section. Note: Programming the system to a community gate will require a unique set of instructions depending on the gate system model. Contact the help line on 1-866-572-2728 for further information. Note: If you accidently enter the program mode by pressing and releasing the outer two buttons or all three buttons simultaneously, do not press any button until the module times out after a few seconds and resets to normal mode. When the module has timed out, all three LED lamps will flash rapidly for a few seconds then turn off. Any settings should remain as previously set. The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. The system includes two primary features, a garage door opener and a platform for remote activation of devices with the home. As well as being programmed for garage doors, the system transmitter can be programmed to operate security devices and home lighting systems. Additional system information can be found on-line at www.learcar2U.com or by calling the toll-free help line on 1-866-572-2728. Types of garage door openers (rolling code and fixed code) The Car2U威 Home Automation System may be programmed to operate rolling code and fixed code garage door openers. • Rolling code garage door openers were produced after 1996 and are code protected. Rolling code means the coded signal is changed every time your remote control garage door opener is used. • Fixed code garage door openers were produced prior to 1996. Fixed

code uses the same coded signal every time. It is manually programmed by setting DIP switches for a unique personal code.

117

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

If you do not know if your garage door opener is a rolling code or fixed code device, open your garage door opener’s remote control battery cover. If a panel of DIP switches is present your garage door opener is a fixed code device. If not, your garage door opener is a rolling code device.

1 2 3 4

9 10 11 12

CTS 206-12 T124

Note: Programming the Car2U威 system to a community gate will require a unique set of instructions depending on the gate system model. Contact the Car2U威 help line at 1-866-572-2728 to program your Car2U威 system. Note: Accidentally entering the program mode may override previously programmed buttons. This can happen by pressing and releasing the outer two buttons, or all three buttons, simultaneously. If this happens, do not press any button until the module times out after approximately 2.5 seconds and resets to normal mode. When time-out occurs, all three LEDs will flash rapidly for a few seconds then turn off. Any settings should remain as previously set. Rolling code programming Note: If you do not follow the time-sensitive instructions, the device will time out and you will have to repeat the complete procedure. Note: It may be helpful to have another person assist you in programming the transmitter. 1. Switch the ignition on.

118

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

2. Press and hold the outer two buttons for 1–2 seconds, then release. Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens. Note: If you cannot locate the learn button, refer to the Owner Manual of your garage door opener or call the toll-free help line on 1-866-572-2728. 3. Press the learn button on the garage door opener motor. Note: You will have 10–30 seconds to complete the following steps. 4. Return to your car. 5. Press and hold the function button you would like to use to control the garage door. You may need to hold the button from 5–20 seconds, during which time the selected button LED lamp will flash slowly. 6. When the garage door moves, release the button within one second. The LED lamp will flash rapidly until programming is complete. 7. Press and release the button again. The garage door should move, confirming that programming is successful. If your garage door does not operate, repeat the previous steps. The LED lamp above the selected button will illuminate to confirm that the system is responding to the button command. To program another rolling code device, repeat steps one through six substituting a different function button in step four.

119

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

Fixed code programming Note: It may be helpful to have another person assist you in programming the transmitter. To program units with fixed code DIP switches, you will need the garage door hand-held transmitter, paper and a pen or pencil. 1. Switch the ignition on. 2. Open the battery cover and note all the switch settings from left to right. When the switch is in the up, on, or + position, mark down “left button”. When the switch is in the middle, neutral, or 0 position, mark down “middle button”. When the switch is in the down, off, or – position, mark down “right button”. 3. Press all three function buttons simultaneously for a few seconds and then release. The LED lamps will flash slowly. Note: The following step must be completed within 2.5 minutes. 4. Enter the corresponding DIP switch settings from left to right into the system by pressing and releasing the buttons corresponding to the settings you noted. 5. Simultaneously press and release all three function buttons. The LED lamps will illuminate. 6. Press and hold the function button you would like to use to control the garage door. Note: You may need to hold the button from 5–55 seconds before observing movement of the garage door.

120

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

7. When the garage door moves, release the button within one second. When the button is released, the LED lamp will flash slowly. 8. The LED lamp will begin to flash rapidly until programming is complete. If your garage door does not operate, repeat the previous steps. Otherwise, call the toll-free help line on 1-866-572-2728. The LED lamp above the selected button will illuminate to confirm that the system is responding to the button command. Erasing the function button codes Note: You cannot erase individual buttons. 1. Press and hold the outer two function buttons simultaneously for approximately 20 seconds until the LED lamps above the buttons flash rapidly. 2. When the LED lamps flash, release the buttons. The codes for all buttons are erased. FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to your device not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment.

121

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)

WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal

area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that the floor mats are properly attached to the retention posts in the carpet that are supplied with your vehicle. Floor mats must be properly secured to both retention posts to ensure mats do not shift out of position. • Never place floor mats or any other covering in the vehicle foot well that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never place floor mats or any other covering on top of already installed floor mats. Floor mats should always rest on top of vehicle carpeting surface and not another floor mat or other covering. Additional floor mats or any other covering will reduce the pedal clearance and potentially interfere with pedal operation. • Check attachment of floor mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning or replacement. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects that are loose can become trapped under the pedals causing a loss of vehicle control. • Failure to properly follow floor mat installation or attachment instructions can potentially cause interference with pedal operation causing loss of control of vehicle.

122

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

WARNING (Continued) • To install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in. • To remove the floor mat, reverse the installation procedure.

TAILGATE LOCK Your vehicle may be equipped with a tailgate lock designed to help prevent theft of the tailgate. • Insert ignition key and turn to the • Turn ignition key to the left to

right to engage lock.

unlock.

Tailgate Removal

WARNING: Always properly secure cargo to prevent shifting cargo or cargo falling from vehicle, which could result in

compromised vehicle stability and serious personal injury to vehicle occupants or others.

Your tailgate is removable to allow more room for loading. Note: If equipped with a rearview camera system, do Steps 1 through 3
before removing the tailgate. 1. Before removal of the tailgate, locate and disconnect the tailgate in-line connector under the pickup box on the passenger side of the vehicle near the spare tire. 2. Install a protective cap (tethered to the wire assembly) onto the in-line rearview camera system connector that remains under the pickup box.

123

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

3. Partially lower tailgate and carefully feed tailgate harness up through the gap between the pickup box and the bumper. Place the tailgate harness out of the way under the pickup box. 4. Lower the tailgate. 5. Using a screwdriver, gently pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 6. Disconnect the other cable. 7. Lift tailgate to a 45-degree angle from horizontal. 8. Lift right side off of its hinge. 9. Lift tailgate to a 80-degree angle from horizontal. 10. Remove tailgate from left side hinge by sliding tailgate to the right. To install, follow the removal procedures in reverse order.

Tailgate Step (If Equipped) Your vehicle may be equipped with a feature that allows easier entry into the truck bed. To open the tailgate step: 1. Flip down the tailgate. 2. Pull the yellow latch lever to the ) to release the unlock position ( grab handle from its stowed position and raise the handle upright until you feel it latch and see the latch ). The lever in the lock position ( yellow lever only needs to be used when releasing the grab handle.

124

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

sufficient lighting

3. Rotate the center molding to unlatch the tailgate step and pull it towards you to extend it. 4. Flip open the step panel to widen the step. Note: To reduce risk of falling: • Operate step only when the vehicle is on level surface. • Operate step only in areas with • Always open flip panel to widen step. • Always use grab handle when stepping up and down. • Step not intended for bare-footed use. • Keep step clean from contamination before use (e.g. snow, mud) • Keep the step load (you + load) below 350 lb (159 kg). • Never drive with step deployed. To close the tailgate step: 1. Close the step panel, then lift and fully close the tailgate step into the tailgate. 2. Slide the latch at the bottom of the handle, then lower the handle. Note: • Fully close and latch the tailgate step before moving the vehicle. • Never drive with the step or grab handle deployed. • Replace slip resistance tape (serviceable item) if worn out. • Replace handle molding (serviceable item) if damaged. • Do not tow with grab handle or step frame.

125

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

Bed extender (if equipped) Your vehicle may be equipped with a cargo management feature in the truck bed. Note: This feature is not intended for off-road usage. To open the bed extender into tailgate mode: 1. Pull the locking pin toward the center of the vehicle.

2. Open the latches to release the panels.

3. Rotate the panels toward the tailgate.

Repeat Steps 1–3 for the other side of the bed extender.

126

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

4. Connect the two panels, then rotate both knobs a quarter-turn clockwise to secure the panels. 5. Ensure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box. 6. Reverse steps for storage of the bed extender.

Note: When the vehicle is in motion, ensure the locking pins and knobs are fully engaged. Note: Ensure all cargo is secured. Note: When the vehicle is in motion, the tailgate load must not exceed 150 lb (68 kg). Note: The bed extender should always be kept in the grocery mode or stowed position with the tailgate closed when not being used for the purpose of restraining cargo in the tailgate mode.

127

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Driver Controls

To open the bed extender into grocery mode, follow Steps 1–4 by rotating the panels away from the tailgate. Close the tailgate.

128

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

KEYS Your vehicle may be equipped with two integrated keyhead transmitters (IKTs). The key blade functions as a programmed key which starts the vehicle and unlocks/locks all the doors. The transmitter portion functions as the remote entry transmitter. Your IKTs are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied IKTs, replacement IKTs are available through your authorized dealer. Standard SecuriLock威 keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. Always carry a spare key with you in case of an emergency. For more information regarding programming replacement IKTs, refer to the SecuriLock威 passive anti-theft system section later in this chapter. Note: Your vehicle’s IKTs were issued with a security tag that provides important vehicle key cut information. It is recommended that you keep the tag in a safe place for future reference.

MYKEY姞 (IF EQUIPPED) The MyKey威 feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to the vehicle can be activated as a MyKey威. The key will remain restricted until MyKey威 is cleared. Any remaining keys are referred to as an “administrator key” or admin key. The admin key can be used to create a MyKey威, program optional MyKey威 settings, and clear the MyKey威 feature. When the MyKey威 feature is enabled the user can use the system check in the message center to see how many MyKeys™ and admin keys are programmed to the vehicle, and how many total miles have been driven with the MyKey威 active.

129

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

MyKey威 restricted features Standard settings – These settings cannot be changed • The audio system will be muted whenever Belt-Minder威 is activated until the safety belts are buckled. Refer to the Seating and Safety Restraints chapter for a detailed description of Belt-Minder威 operation. • Low fuel warnings are displayed in the message center followed by a • If equipped, any of the following: parking aid, Blind Spot Information System (BLIS威) with cross traffic alert and forward collision warning systems cannot be turned off.

chime when the vehicle has only 1/8 tank of fuel.

Optional settings – These settings can be changed • Vehicle speed is limited to 80 mph (130 km/h). Visual warnings are displayed followed by a chime when the vehicle speed has reached 80 mph (130 km/h).

• Visual warnings are displayed followed by a chime when a preselected vehicle speed of 45, 55 or 65 mph (75, 90, or 105 km/h) is exceeded. • The maximum volume of the audio system is limited to 45%. MYKEY VOLUME LIMITED will be displayed in the radio or navigation screen (if equipped) when attempting to exceed the limited volume. • The AdvanceTrac威 system cannot be turned off. When this optional setting is on, the MyKey威 user will not be able to deactivate the system. Note: It may be beneficial to deactivate the AdvanceTrac威 system if the vehicle is stuck in snow, mud, or sand.

Create a MyKey威 To program MyKey威 on one of the keys programmed to the vehicle, insert the key that you want to make a MyKey威 into the ignition. (For vehicles equipped with push button start, put the intelligent access key in the backup slot with the buttons facing out of the slot; see the Driving chapter for the location of the backup slot.) Turn the ignition on. Use the message center buttons to do the following: For standard message center: 1. Press SETUP until PRESS RESET TO CREATE MYKEY is displayed. 2. Press and release the RESET button. HOLD RESET TO CONFIRM MYKEY will be displayed. 3. Press and hold the RESET button for two seconds until MARK THIS AS RESTRICTED is displayed. 4. Wait until KEY RESTRICTED AT NEXT START is displayed. 130

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

For optional message center: 1. At the main menu screen select SETTING then MYKEY by pressing OK or the right arrow key. 2. Press OK to select CREATE MYKEY. 3. Hold OK as prompted until you see MARK THIS KEY AS RESTRICTED. MyKey威 is successfully programmed. Make sure you label it so you can distinguish it from the admin keys. Note: To program the optional settings go to Step 2 in the Programming MyKey威 optional settings section. If your vehicle is equipped with remote start, see the Using MyKey威 with remote start systems section. Note: The MyKey威 can be cleared within the same key cycle that it was created, otherwise a standard key (administrator key) is required to clear the MyKey威 programming. To clear all MyKeys威 go to Step 2 in the Clear MyKey威 section. Programming MyKey威 optional settings To program the optional settings, use the message center buttons to do the following: For standard message center: 1. Press SETUP until RESET FOR MYKEY SETTINGS is displayed. 2. Press and release the RESET button to display MyKey威 setup menus. The first menu shown is:

MYKEY MAX MPH <80 MPH> OFF

3. If you don’t want to change the maximum speed setting, press the SETUP button to display the next menu. The remaining menus appear as follows with the default settings shown: MYKEY MPH TONES 45 55 65 MYKEY VOLUME LIMIT OFF MYKEY ADVTRAC CTRL ON .

4. On any of the menus press RESET to highlight your choice with the <…>. 5. Press SETUP to enter your choice. The next optional setting will be displayed. 6. Repeat Steps 4 and 5 until you are done changing the optional settings.

131

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

For optional message center: 1. At the main menu screen select SETTING then MYKEY by pressing OK or the right arrow key. 2. Use the up and down arrows to get to any of the optional features. 3. Press the right arrow key to bring up the settings available for each feature. 4. Press OK or the right arrow key to make your choice. Clear MyKey威 To reset all MyKeys威 as admin keys do the following: For standard message center: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRM CLEAR is displayed. 4. Press and hold the RESET button for two seconds until ALL MYKEYS CLEARED is displayed. For optional message center: 1. At the main menu screen select SETTING then MYKEY by pressing OK or the right arrow key. 2. Press the down arrow key to get to CLEAR MYKEYS. 3. Hold OK until you see ALL MYKEYS CLEARED. Check MyKey威 system status The vehicle system check will provide the status of the following MyKey威 parameters: • MYKEY MILES — This odometer only tracks distance when a MyKey威 is used. If mileage does not accumulate as expected, then the MyKey威 is not being used by the intended user. The only way to reset this odometer to zero is by clearing MyKey威. If this odometer is lower than the last time you checked, then the MyKey威 system has been recently cleared. • # MYKEY(S) PROGRAMMED — Indicates how many MyKeys威 are • # ADMIN KEYS PROGRAMMED — Indicates how many admin keys are programmed to the vehicle. Can be used to detect if an additional spare key has been programmed to the vehicle

programmed to the vehicle. Can be used to detect deletion of a MyKey威.

Refer to Message center in the Instrument Cluster chapter for MyKey威 system warnings displays. 132

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Using MyKey威 with remote start systems MyKey威 is not compatible with non Ford-approved aftermarket remote start systems. If you choose to install a remote start system please see your authorized dealer for a Ford approved remote start system. The following information MAY help customers who choose to use a non Ford-approved remote start system. The actions proved below do not make MyKey威 compatible with non Ford-approved remote start system, but it MAY help you to retain some MyKey威 functions. Vehicles equipped with traditional keys When using a non Ford-approved remote start system, the default settings may recognize the remote start system as an additional admin key with its associated privileges. This makes it NOT compatible with MyKey威. The following action may help you to retain some MyKey威 functions: 1. Restart the engine when you insert a key into the ignition cylinder. 2. In addition to the key that you have already programmed as a MyKey威, owners of vehicles equipped with traditional keys may want to program the non Ford-approved remote start system as a MyKey威 if the remote start fob is used by the MyKey威 driver. To program a non Ford-approved remote start system as MyKey威, do the following: 1. Enter the vehicle and close all doors. 2. Remote start the vehicle using a remote start fob. 3. Follow steps 1-4 in the Create a MyKey威 section. Vehicles equipped with intelligent access key (push button start) • It is not possible to program any remote start system as MyKey威 on vehicles equipped with an intelligent access key (push button start). Therefore, you should treat the remote start fob as you would any other admin key. When the vehicle is started using remote start, the system will stall the engine when you either enter the vehicle or shift the vehicle into gear. Prior to the engine stall, the vehicle will have administrative privileges. When you restart the engine, the vehicle will identify the user as an admin or MyKey威 drive depending on the settings of the actual key used to start the vehicle.

133

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or ADMIN KEYS PROGRAMMED that is displayed in the MyKey威 system status menus will include the non Ford-approved remote start system as an additional key in the total count. See the Check MyKey威 system status section. Note: For all vehicles with a non Ford-approved remote start installed, it is possible to program all “real” keys as MyKeys威, in which case, you will need to use your remote start system to reset all MyKeys威 as admin keys by doing the following: 1. Enter the vehicle, close all doors. 2. Remote start the vehicle using your remote start fob. 3. Follow steps 1-4 in the Clear MyKey威 section. Using MyKey威 with remote start systems MyKey威 is not compatible with non Ford-approved aftermarket remote start systems. If you choose to install a remote start system please see your authorized dealer for a Ford-approved remote start system. When using a Ford-approved remote start system, the default settings will recognize the remote start system as an additional admin key with its associated privileges. Owners of vehicles equipped with traditional keys should program the remote start system as a MyKey威 in addition to the key that they have already programmed as a MyKey威. To program the remote start system as MyKey威, do the following: 1. Enter the vehicle and close all doors. 2. Remote start the vehicle using a remote start fob. 3. Follow Steps 1-4 in the Create a MyKey威 section. Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or ADMIN KEYS PROGRAMMED that is displayed in the MyKey威 system status menus will include the remote start system as an additional key in the total count. See the Check MyKey威 system status section. Note: For all vehicles with remote start installed, it is possible to program all “real” keys as MyKeys威, in which case, you will need to use your remote start system to reset all MyKeys威 as admin keys by doing the following: 1. Enter the vehicle, close all doors. 2. Remote start the vehicle using your remote start fob. 3. Follow Steps 1-4 in the Clear MyKey威 section.

134

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Troubleshooting Condition Can’t create a MyKey威

Cannot program the MyKey威 optional settings

Cannot clear MyKey威

Lost the only admin key

Lost any key

Locks and Security

Potential Causes • Key in the ignition is already a MyKey威. • Key in the ignition is the last remaining admin key (there always has to be at least one admin key). • SecuriLock威 passive anti-theft system is disabled or in unlimited mode. • Vehicle has been started using a non Ford-approved remote start system that is programmed as MyKey威. Refer to Using MyKey威 with remote start systems section. • Key in the ignition is a MyKey威. • No MyKeys威 are programmed to the vehicle. Refer to Create a MyKey威 section. • Vehicle has been started using a non Ford-approved remote start system that is programmed as MyKey威. Refer to Using MyKey威 with remote start systems section. • Key in the ignition is a MyKey威 . • No MyKeys威 are programmed to the vehicle. Refer to Create a MyKey威 section. • Vehicle has been started using a non Ford-approved remote start system that is programmed as MyKey威. Refer to Using MyKey威 with remote start systems section. • Purchase a new key from your authorized dealer. • For programming spare keys, refer to the Programming spare keys section in this chapter.

135

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Condition I accidentally programmed all keys as MyKeys威

No MyKey威 function with (if equipped) intelligent access key with push button start

MyKey威 programmed total includes one additional key

Admin keys programmed total includes one additional key

MyKey威 distance does not accumulate

Potential Causes • Vehicle has a non Ford-approved remote start system that is recognized as an admin key. Refer to the Using MyKey威 with remote start systems section to reset all MyKeys威 as admin keys. • An admin intelligent access key is present at a push-and-start vehicle. • No MyKeys威 are programmed to the vehicle. Refer to Create a MyKey威 section. • Vehicle has been started using a non Ford-approved remote start system (as an admin key) then a MyKey威 is inserted without restarting the engine. • Unknown key has been programmed to the vehicle as a MyKey威. • Vehicle is equipped with a non Ford-approved remote start system. Refer to Using MyKey威 with remote start systems section. • Unknown key has been programmed to the vehicle as admin key. • Vehicle is equipped with a non Ford-approved remote start system. Refer to Using MyKey威 with remote start systems section. • MyKey威 is not being used by the intended user. • MyKey威 system has been recently cleared. • Vehicles has been started using a non Ford-approved remote start system (as an admin key) then a MyKey威 is inserted without recycling the MyKey威 in ignition.

136

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors.

Locks and Security

Press control to lock all doors.

Smart locks (if equipped) This feature prevents you from locking yourself out of the vehicle if your key is still in the ignition. When you open the driver’s door and you lock the vehicle with the power door lock control, all the doors will lock, then the driver’s door will automatically unlock reminding you that your key is still in the ignition. The vehicle can still be locked, with the key in the ignition, using the manual lock button on the door, locking the driver’s door with a key, by simultaneously pressing button 7 • 8 and the 9 • 0 controls on the button on the remote entry keypad (if equipped), or using the remote entry transmitter (if equipped).

Autolock feature (if equipped) The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h) for greater

than two seconds.

137

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position • the vehicle then attains a speed greater than 12 mph (20 km/h) for

and the vehicle speed is 9 mph (15 km/h) or lower, and

greater than two seconds.

Deactivating/activating autolock feature There are four methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock procedure, • using a keypad procedure (if equipped), or • or by using the instrument cluster message center (if equipped). Refer

to Message center in the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the on position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete. 138

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the off position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. Autounlock feature (if equipped) The autounlock feature will unlock all the doors when: • the ignition is in the on position, all the doors are closed, and the vehicle has been in motion at a speed greater than 12 mph (20 km/h); • the vehicle has then come to a stop and the ignition is turned to the • the driver door is opened within 10 minutes of the ignition being

off ) or accessory position; and

transitioned to the off or accessory position.

Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock feature There are three methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock sequence, • using a keypad procedure (if equipped) • or by using the instrument cluster message center (if equipped). Refer

to Optional message center in the Driver controls chapter.

Note: The autounlock feature can be activated/deactivated independently of the autolock feature.

139

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the on position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete.

Keyless entry keypad autounlock enable/disable procedure 1. Turn the ignition to the off position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second time. 5. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. 140

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

CHILD SAFETY LOCKS (IF EQUIPPED) • When these locks are set, the

rear doors cannot be opened from the inside.

• The rear doors can be opened

from the outside when the childproof door locks are set, but the doors are unlocked.

The childproof locks are located on the rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Move lock control up to engage • Move lock control down to

the childproof lock.

disengage the childproof lock.

REMOTE ENTRY SYSTEM (IF EQUIPPED) The integrated keyhead transmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. There are two possible types of IKTs: vehicles with the remote start feature will have the IKT shown. Vehicle’s without remote start will not have the remote start button

141

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

The typical operating range for your IKT is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely start the engine (if equipped with remote start). • activate the personal alarm. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the start position. The panic feature operates with the key in the off position. If there are problems with the remote entry system, make sure to take ALL integrated keyhead transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.

and release again within three seconds to unlock the

and release to unlock the driver’s door. Note: The parking

Two step door unlocking 1. Press lamps and interior lamps will illuminate (refer to the Illuminated entry feature later in this section) if the control on the overhead lamp is not set to the off position. 2. Press passenger doors. The battery saver feature will turn off the lamps 10 minutes after the ignition is turned to the off position. One step door unlocking If the one step door unlocking feature is activated, press once to unlock all of the doors. Note: The parking lamps and interior lamps will illuminate (refer to the Illuminated entry feature later in this section) if the control on the overhead lamp is not set to the off position. Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can be switched between two step and one step door unlocking by pressing and 142

and release

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

and

buttons simultaneously on the remote entry holding both the transmitter for approximately four seconds. The hazard lamps will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two-step unlocking.

Locking the doors 1. Press illuminate if all the doors are closed and locked.

and release to lock all the doors. The parking lamps will

and release again within three seconds to confirm that all 2. Press the doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will illuminate once more. If any of the doors are not properly closed the horn will make two quick chirps and the parking lamps will not flash.

Car finder twice within three seconds. The horn will chirp and the turn Press lamps will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.

Sounding a panic alarm Press deactivate. Note: The panic alarm will only operate when the ignition is off.

to activate the alarm. Press again or turn the ignition to on to

to automatically move the driver seat, power mirrors and

Memory feature (seat, mirrors and adjustable pedals) The integrated keyhead transmitter (IKT) allows you to recall the memory seat/power mirrors/adjustable pedals feature. Press adjustable pedals to the desired memory position. (The seat position corresponds to the transmitter being used). Programming memory feature to transmitter To activate this feature: 1. Move the driver seat, power mirrors, and adjustable pedals to the desired positions using the associated controls.

143

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

2. Press and hold control button 1
for five seconds. A tone will be heard after two seconds confirming memory position has been set. Continue to hold until a second tone is heard after five seconds. 3. Within three seconds press 4. Wait 10 seconds, then press 5. Repeat this procedure for memory 2 and another transmitter if desired. Deprogramming memory feature from transmitter To deactivate this feature: 1. Press and hold either the 1 or 2 control on the driver’s door for five seconds. A tone will be heard after 11⁄2 seconds when the memory store is done, continue to hold until a second tone is heard after five seconds. 2. Within three seconds press 3. Repeat this procedure for another transmitter if desired.

Replacing the battery The integrated keyhead transmitter (IKT) or intelligent access key (IA key) uses one coin type three-volt lithium battery CR2032 or equivalent. Integrated keyhead transmitter (IKT) To replace the battery: 1. Twist a thin coin in the slot near the key ring to remove the battery cover (1). Note: Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 2. Carefully peel up the rubber gasket (2) from the transmitter if it does not come off with battery cover. 3. Remove the old battery (3). Note: Please refer to local regulations when disposing of transmitter batteries. 144

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

4. Insert the new battery. Refer to the instructions inside the IKT for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the battery cover back onto the key. Note: Replacement of the battery will not cause the IKT or IA key to become de-programmed from your vehicle. They should operate normally after battery replacement.

Replacing lost Integrated Keyhead Transmitters (IKTs) If you would like to have your Integrated Keyhead Transmitters reprogrammed because you lost one, or would like to buy additional IKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to reprogram your Integrated Keyhead Transmitters (IKTs) To program a new Integrated Keyhead Transmitter yourself, refer to Programming spare keys in the SecuriLock威 passive anti-theft system section of this chapter. Note: At least two IKTs are required to perform this procedure yourself.

pressed, or

Illuminated entry The interior lamps and parking lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the lights if: • the ignition switch is turned to the on position, or • the remote transmitter lock control is pressed, or • the 7 • 8 and the 9 • 0 controls on the keyless entry keypad are • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the off position, 10 minutes after if the dome lamp is off, and 30 minutes after if the dome lamp switch is left on.

145

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Remote start (if equipped) Your vehicle may be equipped with the remote start feature which allows you to start the engine from outside the vehicle. If your integrated keyhead transmitter (IKT) has a remote start feature has an extended operating range which allows you to remote start your vehicle from a farther distance from your vehicle. All the buttons have this increased range performance capability when equipped with remote start. Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems. Note: Do not use remote start if your vehicle is low on fuel.

icon, you have remote start. The

WARNING: To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well

ventilated.

hour.

The remote start system will not work if: • The ignition is in the on position. • The alarm system is triggered. • The feature has been disabled. • The hood is not closed. • Two remote vehicle starts have already been attempted within the last • The vehicle is not in P (Park). Starting the engine with remote start To start the engine using remote start: Note: Each button press must be done within 3 seconds of each other. If this sequence is not followed the vehicle will not remote start and the horn will not chirp. 1. Press 2. Press

on the IKT to lock all the doors. two times. The exterior lamps will flash twice.

Note: On diesel engines there will be a 3 second delay before the engine starts. If for some reason, the system fails to start, the horn will chirp twice. 3. Insert the key in the ignition and turn to the on position before driving. 146

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

The power windows will be inhibited during the remote start and the radio will not turn on. The parking lamps will remain on and the engine will run for 5, 10, or 15 minutes, depending on how you programmed the system. To select the duration of the remote start system refer to Message center in the Instrument Cluster chapter. Extending the engine run time To keep the engine running for another remote start duration, repeat Steps 1 and 2 with the engine still running. If you programmed the duration to last 10 minutes, the second 10 minutes will begin immediately so that, for example, if the vehicle had been running from the first remote start for five minutes, the engine will continue to run for a total of 15 minutes. You can only extend the remote start once. If the vehicle is remote started then remote stopped, wait at least five seconds before remote starting a second time. The ignition switch must be turned to the on position and then back to the off position or allow one hour to pass before using remote start again. Turning the engine off after using remote start • Press

one time. The parking lamps will turn off.

You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running engine.

You can disable or enable the remote start system through the message center. Refer to Message center in the Instrument Cluster chapter.

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to lock or unlock the doors without using a key. The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

147

2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)

Locks and Security

Programming a personal entry code and keypad association to memory feature To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. To associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 settings. • Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting. Note: The factory-set code cannot be associated with a memory setting.

5. The doors will again lock then unlock to confirm that your personal entry code has been programmed to the module. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal

code.

Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. Your personal code is now erased and only the factory set 5–digit code