Download PDF Manual

Note: If the system cannot be turned off, refer to MyKey威 in the Locks and Security chapter for more information. When AdvanceTrac威 with RSC威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off. When an event occurs that activates AdvanceTrac威 with RSC威 you may experience the following: • A slight deceleration of the vehicle • The stability control light will flash. • A vibration in the pedal when your foot is on the brake pedal • If the driving condition is severe and your foot is not on the brake, the brake pedal may move as the systems applies higher brake forces. You may also hear a whoosh of air from under the instrument panel during this severe condition.


• The brake pedal may feel stiffer than usual. Traction control system (TCS) Traction control is a driver aid feature that helps your vehicle maintain traction of the wheels, typically when driving on slippery and/or hilly road surfaces, by detecting and controlling wheel spin. Excessive wheel spin is controlled in two ways, which may work separately or in tandem: engine traction control and brake traction control. Engine traction control works to limit drive-wheel spin by momentarily reducing engine power. Brake traction control works to limit wheel spin by momentarily applying the brakes to the wheel that is slipping. Traction control is most active at low speeds. During TCS events the stability control light in the instrument cluster will flash. If the TCS is activated excessively in a short period of time, the braking portion of the system may become temporarily disabled to allow the brakes to cool down. In this situation, TCS will use only engine power reduction to help control the wheels from over-spinning. When the brakes have cooled down, the system will regain all features. Anti-lock braking, RSC威, and ESC are not affected by this condition and will continue to function during the cool-down period. The engine traction control and brake traction control system may be deactivated in certain situations. See the Switching off AdvanceTrac威 with RSC威 section following.


277


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway. ESC operates by applying brakes to one or more of the wheels individually and, if necessary, reducing engine power if the system detects that the vehicle is about to skid or slide laterally. During ESC events, the stability control light in the instrument cluster will flash. Certain adverse driving maneuvers may activate the ESC system, which include but are not limited to: • Taking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Driving over a patch of ice or other slippery surfaces • Changing lanes on a snow-rutted road • Entering a snow-free road from a snow-covered side street, or vice • Entering a paved road from a gravel road, or vice versa • Cornering while towing a heavily loaded trailer (refer to Trailer


versa


towing in the Tires, Wheels and Loading chapter).


The ESC system may be deactivated in certain situations. See the Switching off AdvanceTrac威 with RSC威 section following. Roll Stability Control™ (RSC威) Roll Stability Control™ (RSC威) may help to maintain roll stability of the vehicle during adverse maneuvers. RSC威 operates by detecting the vehicle’s roll motion and the rate at which it changes and by applying the brakes to one or more wheels individually. During an event that activates the Roll Stability Control™ (RSC威) the stability control light in the instrument cluster will flash. Certain adverse driving maneuvers may activate the Roll Stability Control™ system, which include: • Emergency lane-change • Taking a turn too fast • Quick maneuvering to avoid an accident, pedestrian or obstacle The Roll Stability Control™ system may be deactivated in certain situations. See the Switching off AdvanceTrac威 with RSC威 section following. 278


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Switching off AdvanceTrac威 with RSC威 If the vehicle is stuck in snow, mud or sand, and seems to lose engine power, switching off certain features of the AdvanceTrac威 with RSC威 system may be beneficial because the wheels are allowed to spin. This will restore full engine power and will enhance momentum through the obstacle. To switch off the AdvanceTrac威 with RSC威 system, press the stability control button located on the instrument panel to the right of the climate control system. Full features of the AdvanceTrac威 with RSC威 system can be restored by pressing the button again or by turning off and restarting the engine. If you switch off the AdvanceTrac威 with RSC威 system, the stability control off light will illuminate steadily. Pressing the stability control button again will turn off the stability control off light and reactivate the system. In R (Reverse), ABS and the engine traction control and brake traction control features will continue to function; however, ESC and RSC威 are disabled.


AdvanceTrac威 with RSC威 Features (SRW only)


Stability control light Illuminated during bulb


check


Illuminated


solid


Flashes then illuminated


solid2


RSC威


ESC


TCS


Enabled


Enabled


Enabled


Enabled


Enabled1


Disabled


Disabled


Disabled


Disabled


Illuminated


solid


Enabled


Enabled1


Disabled


Button functions


Default at start-up


Button pressed momentarily Button pressed and held for more than 5 seconds at vehicle speed under 35 mph (56 km/h) Vehicle speed exceeds 35 mph (56 km/h) after button is pressed and held for more than 5 seconds


279


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


AdvanceTrac威 with RSC威 Features (SRW only)


Button functions


Stability control light


RSC威


ESC


TCS


Not


Enabled


Enabled


Enabled


Disabled


Disabled


illuminated


Illuminated


Button pressed again after deactivation Transfer case switched to 4WD Low 3
1ESC has reduced sensitivity compared to fully active system. 2Lamp light starts blinking for 4 seconds after entering press and hold state. 3Engaging 4WD Low locked automatically disables RSC, ESC and TSC. Trailer sway control Your vehicle may be equipped with trailer sway control. When properly equipped, trailer sway control will use the vehicle’s AdvanceTrac威 with RSC威 system to detect and help reduce trailer sway by applying brake force at individual wheels and, if necessary, by reducing engine power.


Disabled


WARNING: Trailer sway control does not prevent a trailer from swaying, it mitigates the sway from increasing once it has


occurred. If you are experiencing trailer sway it is likely that the trailer is improperly loaded for the correct tongue weight or the speed of the vehicle and trailer is too high. Pull the vehicle-trailer over to a safe location to check the trailer weight distribution and tongue load and reduce speed to a safe level while towing. If trailer sway is experienced, SLOW DOWN.


During trailer sway control events the stability control light in the instrument cluster will flash momentarily. The message center will also display TRAILER SWAY REDUCE SPEED. In some cases when trailer sway is detected, the vehicle speed is too high and may be above a speed at which trailer sway will not grow continuously. This may cause the system to activate multiple times, causing a gradual reduction in speed.


280


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Disabling trailer sway control Trailer sway control can be disabled during any key cycle. See trailer sway control under the Message center in the Instrument Cluster chapter. Note that regardless of chosen enable state, trailer sway control will be re-enabled at each new key cycle.


WARNING: Turning off trailer sway control increases the risk of loss of vehicle control, serious injury, or death. Ford does not recommend disabling this feature except in situations where speed reduction may be detrimental (e.g., hill climbing), the driver has significant trailer towing experience, and can control trailer sway and maintain safe operation.


HILL DESCENT CONTROL (IF EQUIPPED) Hill descent control allows the driver to set and maintain vehicle speed while descending steep grades in various surface conditions.


WARNING: Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep grades. Hill descent control is a driver assist system and cannot substitute for good judgment by the driver. Failure to do so may result in loss of vehicle control, crash or serious injury.


Hill descent control can maintain vehicle speeds on downhill grades between 2 mph (3 km/h) and 12 mph (20 km/h). Above 20 mph (32 km/h), the system remains armed, but descent speed cannot be set or maintained.


WARNING: Hill descent control does not provide hill hold at zero mph (0 km/h). When stopped, the parking brake must be applied and/or the vehicle must be placed in P (Park) or it may roll away.


Hill descent control requires a cooling down interval after a period of sustained use. The amount of time that the feature can remain active before cooling varies with conditions. The system will provide a warning in the message center and a chime will sound when the system is about to disengage for cooling. At this time, manually apply the brakes as needed to maintain descent speed.


281


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Enabling hill descent control and setting the descent speed 1. Press and release the hill descent button located on the instrument panel. A light in the cluster will illuminate and chime will sound when this feature is activated.


2. To increase descent speed, press the accelerator pedal until the desired speed is reached. To decrease descent speed, press the brake pedal until the desired speed is reached. Whether accelerating or decelerating, once the desired descent speed is reached, remove your feet from the pedals and the chosen vehicle speed will be maintained. Note: Noise from the ABS pump motor may be observed during hill descent control operation. This is a normal characteristic of the ABS and should be no reason for concern. Hill descent modes • At speeds below 20 mph (32 km/h): When the HDC switch is pressed • At speeds below 20 mph (32 km/h): When the HDC switch is pressed


and HDC is active, the HDC telltale will flash.


and conditions are not correct for hill descent activation, the HDC system will be enabled, the light in the cluster will be on solid and HILL DESCENT CONTROL READY will be displayed in the message center. • At speeds above 20 mph (32 km/h): When the HDC switch is pressed, the HDC system will be enabled, the light in the cluster will not be illuminated and FOR HILL CNTRL, 20 MPH OR LESS will be displayed in the message center.


Refer to Message center in the Instrument Cluster chapter for hill descent control messages.


STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than three to five seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level


(below the MIN mark on the reservoir).


282


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


• Some noise is normal during operation. If excessive, check for low power steering pump fluid level before seeking service by your dealer. • Heavy or uneven efforts may be caused by low power steering fluid. Check for low power steering pump fluid level before seeking service by your dealer. • Do not fill the power steering pump reservoir above the MAX mark on


the reservoir, as this may result in leaks from the reservoir.


If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment If any steering components are serviced or replaced, install new fasteners (many are coated with thread adhesive or have prevailing torque features which may not be re-used). Never re-use a bolt or nut. Torque fasteners to specifications in Workshop Manual. A high crown in the road or high crosswinds may also make the steering seem to wander/pull.


ELECTRONIC LOCKING DIFFERENTIAL (ELD) (IF EQUIPPED) The electronic locking differential (ELD) is a device housed in the rear axle which allows both rear wheels to turn at the same speed. It provides added traction on slippery and/or off road surfaces, particularly when one wheel is on a poor traction surface. The ELD may be locked or unlocked by the vehicle operator and can be engaged or disengaged on the fly. When the axle is unlocked it will function like a standard rear axle. When the axle is locked it will not allow the rear wheels to rotate at different speeds when turning. It is not recommended for use on good traction surfaces such as dry pavement. Doing so may result in abnormal driving behavior and noise while cornering and excessive tire wear. The ELD is affected by the following conditions of your vehicle: • On 2WD vehicles and 4WD vehicles in 2H (4X2) or 4H (4X4 High),


the ELD will not engage if the vehicle speed is above 25 mph (40 km/h).


283


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving • On 2WD vehicles and 4WD vehicles in 2H (4X2) or 4H (4X4 High), the ELD will automatically disengage at speeds above 25 mph (40 km/h) and will automatically reengage at speeds below 19 mph (30 km/h). • On 4WD vehicles in 4L (4X4 Low), the ELD can be engaged at any


speed and will not automatically disengage.


Activating the electronic locking differential (ELD) For vehicles equipped with an electronic shift 4WD system: Pull the knob on the 4WD control toward you. The indicator light will display in the instrument cluster.


For 2WD vehicles and vehicles equipped with a manual shift 4WD system: Turn the control to ON. The indicator light will display in the instrument cluster.


light is displayed in the instrument cluster, both rear wheel


indicator light in the instrument cluster turns off, one of the


Once the axle shafts will be locked together providing added traction. If the following has occurred: • The vehicle speed is too high. • The left and right rear wheel speed difference is too high during an • The system has malfunctioned and will be accompanied by the


engagement attempt.


CHECK LOCKING DIFFERENTIAL message in the message center. See your authorized Ford dealer for assistance.


Note: The ELD may have difficulty disengaging either by operator command or automatically if the driveline is under torque. If driving conditions allow, releasing the accelerator pedal or turning the steering wheel in the opposite direction may assist in disengagement. Note: The ELD is designed for off-road use only and is not intended for use on dry pavement. 284


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


PREPARING TO DRIVE


WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.


WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.


Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher center of gravity than a passenger car.


WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed or abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.


WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Do not overload


your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle. Over-loading or loading the vehicle improperly can deteriorate handling capability and contribute to loss of vehicle control and vehicle rollover.


BRAKE-SHIFT INTERLOCK This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the 3 (on) position and the brake pedal is not pressed. If you cannot move the gearshift lever out of P (Park) with ignition in the on position and the brake pedal pressed, it is possible that a fuse has blown or the vehicle’s brake lamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter.


285


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


If the fuse is not blown and the brake lamps are working properly, the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake. Turn the ignition key to 1 (off), then remove the key. 2. Move the steering column to the full down and full rearward position (toward the driver’s seat). 3. Remove the gearshift lever boot. 4. Place fingers into hole where the gearshift lever boot was removed from and pull top half of shroud up and forward to separate it from the lower half of the shroud. There is a hinge at the forward edge of the top shroud. Roll the top half of the shroud upward on the hinge point to clear the hazard flasher button, then pull straight rearward toward the driver’s seat to remove. 5. Remove the top half of the shroud. 6. Remove the three fasteners under the column that secure the lower shroud half to the column.


7. Pull the lock lever into the full unlocked position and remove the lower shroud cover by pulling the lever handle through the slot in the cover.


8. Apply the brake and move the gearshift lever into N (Neutral). 9. Start the vehicle. Perform Steps 4 through 8 in reverse order, making sure to engage the hinge pivots between the upper and lower halves of the shroud. Keep slight pressure in the forward direction as the halves are rotated together. 286


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


WARNING: Do not drive your vehicle until you verify that the brake lamps are working.


WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure. Use wheel chocks if appropriate.


WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be


working properly. See your authorized dealer as soon as possible.


AUTOMATIC TRANSMISSION OPERATION


Understanding the shift positions of the 5–speed automatic transmission (if equipped)


This vehicle is equipped with an adaptive transmission shift strategy. Adaptive transmission shift strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected. The adaptive transmission shift strategy allows the transmission to relearn these operating parameters. This learning process could take several transmission upshifts and downshifts; during this learning process, slightly firmer shifts may occur. After this learning process, normal shift feel and shift scheduling will resume. P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine • Press the brake pedal • Move the gearshift lever into the desired gear


287


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park)


WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off


position and remove the key whenever you leave your vehicle.


R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with Tow/Haul Off D (Overdrive) with tow/haul off is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through five. D (Overdrive) with Tow/Haul On The tow/haul feature improves transmission operation when towing a trailer or a heavy load. All transmission gear ranges are available when using tow/haul. To activate tow/haul, press the button on the end of the gearshift lever.


The TOW HAUL indicator light will illuminate in the instrument cluster. Tow/haul delays upshifts to reduce frequency of transmission shifting. Tow/haul also provides engine braking in all forward gears when the transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the driver in controlling the vehicle when descending a grade. Depending on driving conditions and load conditions, the transmission may downshift, slow the vehicle and control the vehicle speed when descending a hill, without the accelerator pedal being pressed. The amount of downshift braking provided will vary based upon the amount the brake pedal is depressed. 288


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


To deactivate the tow/haul feature and return to normal driving mode, press the button on the end of the gearshift lever. The TOW HAUL light will no longer be illuminated. When you shut-off and restart the engine, the transmission will automatically return to normal D (Overdrive) mode (Tow/Haul OFF).


WARNING: Do not use the tow/haul feature when driving in icy or slippery conditions as the increased engine braking can cause


the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control.


3 (Third) Transmission starts and operates in third gear only. Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • The transmission will not downshift into 1 (First) at high speeds; it will downshift to a lower gear and then shift into 1 (First) when the vehicle reaches slower speeds.


Forced downshifts • Allowed in D (Overdrive) or D (Drive). • Press the accelerator to the floor. • Allows transmission to select an appropriate gear.


289


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Understanding the shift positions of the 6–speed automatic transmission (if equipped)


This vehicle is equipped with an adaptive transmission shift strategy. Adaptive transmission shift strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected. The adaptive transmission shift strategy allows the transmission to relearn these operating parameters. This learning process could take several transmission upshifts and downshifts; during this learning process, slightly firmer shifts may occur. After this learning process, normal shift feel and shift scheduling will resume. P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: 1. Start the engine 2. Press the brake pedal 3. Move the gearshift lever into the desired gear To put your vehicle in P (Park): 1. Come to a complete stop 2. Move the gearshift lever and securely latch it in P (Park)


WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off


position and remove the key whenever you leave your vehicle.


R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). 290


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with Tow/Haul Off D (Overdrive) with tow/haul off is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through six. D (Overdrive) with Tow/Haul On The tow/haul feature improves transmission operation when towing a trailer or a heavy load. All transmission gear ranges are available when using tow/haul. To activate tow/haul, press the button on the end of the gearshift lever.


The TOW HAUL indicator light will illuminate in the instrument cluster.


Tow/haul delays upshifts to reduce frequency of transmission shifting. Tow/haul also provides engine braking in all forward gears when the transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the driver in controlling the vehicle when descending a grade. Depending on driving conditions and load conditions, the transmission may downshift, slow the vehicle and control the vehicle speed when descending a hill, without the brake pedal being pressed. The amount of downshift braking provided will vary based upon the amount the brake pedal is pressed. Tow/haul may be automatically activated (without pressing the tow/haul button). This provides engine braking to assist the vehicles braking system when going downhill and repetitive braking is sensed. Once the tow/haul mode has been automatically activated it will not automatically deactivate.


291


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


To deactivate the tow/haul feature and return to normal driving mode, press the button on the end of the gearshift lever. The tow/haul light will no longer be illuminated. Tow/haul will also deactivate when the vehicle is powered down for a few minutes.


WARNING: Do not use the tow/haul feature when driving in icy or slippery conditions as the increased engine braking can cause


the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control.


M (Manual) without Overdrive With the gearshift lever in M (Manual), the driver can change gears up or down as desired. This is called SelectShift Automatic™ transmission (SST) mode. By moving the gearshift lever from drive position D (Overdrive) to M (Manual) you now have control of selecting the gear you desire using buttons on the shift lever. To return to normal D (Overdrive) position, move the shift lever back from M to D. • The transmission will operate in gears one through six. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • The transmission will not downshift into 1 (First) at high speeds; it will downshift to a lower gear and then shift into 1 (First) when the vehicle reaches slower speeds.


Forced downshifts • Allowed in D (Overdrive). • Press the accelerator to the floor. • Allows transmission to select an appropriate gear.


292


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Understanding your SelectShift Automatic™ transmission (SST) gearshift lever This vehicle is equipped with a SelectShift Automatic™ transmission (SST) gearshift lever. The SST is an automatic transmission with the ability for the driver to change gears up or down (without a clutch) as desired. Use the buttons on the shifter to lock or unlock gears and manually select gears. Press the + button to upshift or the – button to downshift.


With the gearshift lever in D (Drive), press the – button to active SST. The available and selected gears will be indicated on the instrument cluster.


All available gears will be displayed with the current gear indicated. Press the – button again to lock out gears beginning with the highest gear. Example: press the – button twice to lock out 6th and 5th gears. Only the available gears will be displayed and the transmission will automatically shift between the available gears. Press the + button to unlock gears. By moving the gearshift lever from the D (Drive) position to the M (Manual) position you may now manually select the gear you desire. Only the current gear will be displayed. Press the + button or the – button to upshift or downshift. If the – button is pressed at a vehicle speed that would cause an engine overspeed, the requested gear will flash then disappear and the transmission will remain in the current gear.


293


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Recommended shift speeds Upshift according to the following chart:


Upshifts when accelerating (recommended for best fuel economy)


Shift from:


1 – 2
2 – 3
3 – 4
4 – 5
5 – 6


Gasoline engines 15 mph (24 km/h) 25 mph (40 km/h) 40 mph (64 km/h) 45 mph (72 km/h) 50 mph (80 km/h)


Diesel engines 12 mph (19 km/h) 19 mph (31 km/h) 26 mph (42 km/h) 34 mph (55 km/h) 46 mph (74 km/h) In order to prevent the engine from running at too low an RPM, which may cause it to stall, the SST will still automatically make some downshifts if it has determined that you have not downshifted in time. Although the SST will make some downshifts for you, it will still allow you to downshift at any time as long as the SST determines that the engine will not be damaged from over-revving. The SST will not automatically upshift, even if the engine is approaching the RPM limit. It must be shifted manually by pressing the + button. Engine damage may occur if excessive engine revving is held without shifting.


Hill start assist (HSA) The hill start assist feature makes it easier to pull away when the vehicle is on a slope without the need to use the parking brake. When the hill start assist feature is active, the vehicle will remain stationary on the slope for up to two seconds after you release the brake pedal. During this time, you have time to move your foot from the brake to the accelerator pedal and pull away. The brakes are released automatically once the engine has developed sufficient drive to prevent the vehicle from rolling down the slope. This is an advantage when pulling away on a slope; for example from a car park ramp, traffic lights or when reversing uphill into a parking space.


WARNING: The hill start assist feature does not replace the parking brake. When you leave the vehicle, always apply the


parking brake and select first or reverse gear.


294


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Using hill start assist The hill start assist feature is activated automatically when the vehicle is stopped on a slope greater than five degrees. The hill start assist feature operates with the vehicle facing downhill if reverse gear is selected. The hill start assist feature will not operate if the parking brake is activated.


WARNING: You must remain in the vehicle once you have activated the hill start assist feature.


Activating hill start assist 1. Press the brake pedal to bring the vehicle to a complete standstill. Keep the brake pedal pressed. 2. If the sensors detect that the vehicle is on a slope, the hill start assist feature will be activated automatically. 3. When you remove your foot from the brake pedal, the vehicle will remain on the slope without rolling away for approximately up to two seconds. This hold time will automatically be extended if you are in the process of driving off. 4. Drive off in the normal manner. The brakes will be released automatically.


WARNING: If the engine is revved excessively, or if a malfunction is detected when the hill start assist feature is


active, the hill start assist feature will be deactivated.


If Your Vehicle Gets Stuck in Mud or Snow Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Note: Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear.


295


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects.


WARNING: To help avoid personal injury, please read and understand the limitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at “parking speeds”. Inclement weather may also affect the function of the RSS; this may include reduced performance or a false activation.


WARNING: To help avoid personal injury, always use caution when in reverse and when using the RSS.


WARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.


WARNING: Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps.


296


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the RSS detects a stationary or receding object further than 10 inches (25.0 cm) from the side of the vehicle, the tone will sound for only three seconds. Once the system detects an object approaching, the tone will sound again. While receiving a warning the radio volume may be reduced to a predetermined level. After the warning goes away, the radio will return to the previous volume. The RSS may have reduced performance or an increased chance of false detection if the tailgate is not locked and in the upright position. If the tailgate is down, the RSS tone may be heard intermittently or continuously. The tone may also be heard if items in the truck bed protrude rearward outside the bed. The RSS automatically turns on when the gearshift lever is placed in R (Reverse) and the ignition is on. A control in the message center allows the driver to disable the system. Refer to Message center in the Instrument Cluster chapter for more information. Note: If the system cannot be turned off, refer to MyKey™ restricted features in the Locks and Security chapter for more information. Note: If your vehicle is equipped with a fully integrated electronic trailer brake controller (TBC) and a trailer with electric trailer brakes is connected to your vehicle, the RSS will be disabled. When the vehicle is shifted into reverse, the message center display will remain in the Rear Park Aid Off selection. For more information on the TBC, refer to the Tires, Wheels and Loading chapter.


297


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Keep the RSS sensors (located on the rear bumper/fascia) free from snow, ice and large accumulations of dirt (do not clean the sensors with sharp objects). If the sensors are covered, it will affect the accuracy of the RSS. If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.


REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system, located on the tailgate, provides a video image, which appears in the rearview mirror or on the navigation screen (if equipped), of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle.


To use the camera system, place the transmission in R (Reverse); an image will display on the left portion of the rearview mirror or on the navigation screen (if equipped). The area displayed on the screen may vary according to the vehicle orientation and/or road condition.


298


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


• (1) Rear bumper • (2) Red zone • (3) Yellow zone • (4) Green zone • (5) Centerline of vehicle Always use caution while backing. Objects in the red zone are closest to your vehicle and objects in the green zone are further away. Objects are getting closer to your vehicle as they move from the green zone to the yellow or red zones. Use the side mirrors and rearview mirror to get better coverage on both sides and rear of the vehicle. Image delay if displayed through the rearview mirror: When shifting out of R (Reverse) and into any other gear, the image in the rearview mirror will remain on for a few seconds before it shuts off to assist in parking or trailer hookup. Image delay if displayed through the navigation screen: After shifting out of R (Reverse) and into any gear other than P (Park), the image in the navigation screen will remain until the vehicle speed reaches 5 mph (8 km/h), only if the rear camera delay feature is on, or until any navigation radio button is pressed. Note: The default setting for the rear camera delay is off. Press the “Settings” button found on the navigation screen (if equipped) to set the rear camera delay feature to on or off. When towing, the camera system will only see what is being towed behind the vehicle; this might not provide adequate coverage as it usually provides in normal operation and some objects might not be seen. The camera lens for the camera is located on the tailgate. Keep the lens clean so the video image remains clear and undistorted. Clean the lens with a soft, lint-free cloth and non-abrasive cleaner. Note: If the camera system image is not clear or seems distorted, it may be covered with water droplets, snow, mud or any other substance. If this occurs, clean the camera lens before using the camera system.


299


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


WARNING: The camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with


the rear view mirror and the side mirrors for maximum coverage.


WARNING: Objects that are close to either corner of the bumper or under the bumper, might not be seen on the screen


due to the limited coverage of the camera system.


WARNING: Back up as slow as possible since higher speeds might limit your reaction time to stop the vehicle.


WARNING: Do not use the camera system with the tailgate open.


If the back end of the vehicle is hit or damaged, then check with your authorized dealer to have your rearview camera system checked for proper coverage and operation. Night time and dark area use At night time or in dark areas, the camera system relies on the reverse lamp lighting to produce an image. Therefore it is necessary that both reverse lamps are operating in order to get a clear image in the dark. If either of the lamps are not operating, stop using the camera system, at least in the dark, until the lamp(s) are replaced and functioning. Servicing • If the image comes on while the vehicle is not in R (Reverse), have • If the image is not clear, then check if there is anything covering the lens such as dirt, mud, ice, snow, etc. If the image is still not clear after cleaning, have your system inspected by your authorized dealer.


the system inspected by your authorized dealer.


300


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)


WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in


this chapter.


When four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD can be selected when additional driving power is desired. 4WD operation is not recommended on dry pavement. Doing so could result in difficult disengagement of the transfer case, increased tire wear and decreased fuel economy.


Manual Shift On Stop (MSOS) 4x4 system (if equipped) The 4WD system is engaged or disengaged by rotating the control for both front wheel hub locks from the FREE or LOCK position, then manually engaging or disengaging the transfer case with the floor-mounted shifter. For increased fuel economy in 2WD, rotate both hub locks to the FREE position. • For proper operation, make sure that each hub is fully engaged and that both hub locks are set to the same position (both set to LOCK or both set to FREE). To engage LOCK, turn the hub locks completely clockwise; to disengage the hubs (FREE), turn the hub locks completely counterclockwise. • The vehicle should not be driven in 4X4 High or 4X4 Low


modes with the hub locks set to FREE as this condition may damage driveline system components.


• Some vehicles may be equipped with wheel ornaments that cover the


4x4 manual hub lock. These ornaments must be removed to access the manual hub locks.


Electronic Shift-On-the-Fly (ESOF) 4x4 system (if equipped) If equipped with the electronic shift 4WD system, and 4X4 Low is selected while the vehicle is moving above 3 mph (5 km/h), the 4WD system will not perform a shift. This is normal and should be no reason for concern. Refer to Shifting to/from 4L (4X4 Low) for proper system operation.


301


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


moving.


allows you select 4x2, 4x4 High or 4x4 Low operation.


The ESOF 4WD system: • provides 4x4 High engagement and disengagement while the vehicle is • is operated by a rotary control located on the instrument panel that • uses auto-manual hub locks that can be engaged and disengaged • auto-manual hub locks can be manually overridden by rotating the hub lock control from AUTO to LOCK if desired.


automatically based on the 4x4 mode selected.


• automatic operation of the


hub locks is recommended, and will increase fuel economy


• For proper operation, make sure that each hub is fully engaged and that both hub locks are set to the same position (both set to LOCK or both set to AUTO). To engage LOCK, turn the hub locks completely clockwise; to engage AUTO, turn the hub locks completely counterclockwise.


4WD system indicator lights The indicator lights illuminate in the message center in the reconfigurable telltale (RTT) under the following conditions. Refer to Warning lights and chimes in the Instrument Cluster chapter. • 4X2 - Momentarily illuminates


4x2


4x4
HIGH


4x4
LOW


when 2H is selected on electronic shift 4WD systems only.


• 4X4 HIGH - Illuminates when 4H


(4x4 High) is engaged.


• 4X4 LOW - Illuminates when 4L • CHECK 4X4 – Displays when a


(4x4 Low) is engaged.


4x4 system fault is present


302


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Using a Manual Shift On Stop (MSOS) 4x4 system (if equipped) Note: High shift efforts may be encountered when attempting to shift into and out of 4x4 modes. It is recommended to allow the vehicle to roll at a speed below 3 mph (5 km/h) when shifting between modes. Note: Some noise may be heard as the 4x4 system shifts or engages. This is normal. In order to reduce engagement noise, it is recommended that all shifts be performed at speeds below 3 mph (5 km/h). 2H (2WD) – For general on-road driving. Sends power to the rear wheels only should be used for street and highway driving. Provides optimal smoothness and fuel economy at high speeds. 4H (4x4 High) – Used for extra traction such as in snow or icy roads or in off road situations. This mode is not intended for use on dry pavement. N (Neutral) – Only used when towing the vehicle. No power to front or rear wheels. 4L (4x4 Low) – Uses extra gearing to provide maximum power to all four wheels at reduced speeds. Intended only for off road applications such as deep sand, steep grades or pulling heavy objects. Shifting from 2H (2WD) to 4H (4x4 High) Engage the locking hubs by rotating the hub lock control from FREE to LOCK, then move the transfer case lever from 2H (2WD) to 4H (4x4
High) at a stop or a vehicle speed below 3 mph (5 km/h). • For proper operation, make


sure that both indicator arrows on the hub are aligned, and that both hubs are set to LOCK.


303


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving • Do not shift into 4H (4x4
High) with the rear wheels slipping. • The vehicle should not be driven in 4X4 High with the hub locks disengaged as this condition may damage driveline system components.


Shifting from 4H (4x4 High) to 2H (2WD) Move the transfer case lever to 2H (2WD) at a stop or a vehicle speed below 3 mph (5 km/h). With the vehicle at complete stop, disengage the locking hubs (optional) by rotating the hub lock control from LOCK to FREE. • For proper operation, make


2H 4H


4L


2H 4H


4L


sure that both indicator arrows on the hub are aligned, and that both hubs are set to FREE.


Shifting from 2H (2WD) or 4H (4x4 High) to 4L (4x4 Low) 1. Bring the vehicle to a stop or a speed below 3 mph (5 km/h). 2. Place the transmission in N (Neutral). 3. Move the transfer case shift lever through N (Neutral) directly to 4L (4x4 Low). 4. If the shift lever does not, or only partially moves to the 4L (4x4 Low) position, perform a shift with the transmission in N (Neutral) and the vehicle rolling at a speed below 3 mph (5 km/h). This will ensure the transfer case is fully engaged into 4L (4x4 Low). Note: The vehicle should not be driven in 4X4 High with the hub locks disengaged as this condition may damage driveline system components.


2H 4H


4L


304


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


4L


2H 4H


Shifting from 4L (4x4 Low) to 4H (4x4 High) or 2H (2WD) 1. Bring the vehicle to a stop or a speed below 3 mph (5 km/h). 2. Place the gearshift lever in N (Neutral). 3. Move the transfer case shift lever through N (Neutral) directly to 4H (4x4 High) or 2H (2WD). 4. If the transfer case will not engage into 4H (4x4 High) or 2H (2WD), perform a shift with the transmission in N (Neutral) and the vehicle rolling at a speed below 3 mph (5 km/h). 5. If shifting to 2H (2WD) with the vehicle at a complete stop, disengage the locking hubs (optional) by rotating the hub lock control from LOCK to FREE. Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards. This position should only be used when towing the vehicle.


2H 4H


4L


WARNING: Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking


brake fully and turn off the ignition when leaving the vehicle.


305


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Using the electronic shift 4WD system (if equipped) 2H (2WD) - For general on-road driving. Sends power to the rear wheels only and should be used for street and highway driving. Provides optimal smoothness and fuel economy at high speeds. 4H (4X4 HIGH) - Used for extra traction such as in snow or icy roads or in off road situations. This mode is not intended for use on dry pavement. 4L (4X4 LOW) - Uses extra gearing to provide maximum power to all four wheels at reduced speeds. Intended only for off-road applications such as deep sand, steep grades, or pulling heavy objects. 4L (4x4 low) will not engage while the vehicle is moving above 3 mph (5 km/h); this is normal and should be no reason for concern. Refer to Shifting to/from 4L (4x4 low) for proper operation. Shifting between 2H (4X2) and 4H (4X4 High) Move the 4WD control between 2H (4X2) and 4H (4X4 HIGH ) at any forward speed. The message center will display 4X4 SHIFT IN PROGRESS during the system shift. 4X4 HIGH will display in the message center if 4H is selected and 4X2 will momentarily display in the message center if 2H is selected. If SHIFT DELAYED PULL FORWARD is displayed in the message center during the mode shift, transfer case gear tooth blockage is present. To alleviate this condition, place the transmission in a forward gear and move the vehicle forward approximately 5 feet (2 meters) to allow the transfer case to complete the mode shift. Note: Momentarily releasing the accelerator pedal while performing a shift will improve engagement/disengagement times. Note: Do not perform this operation if the rear wheels are slipping. Note: Some noise may be heard as the system shifts or engages; this is normal. Note: 4X4 high mode is not intended for use on dry pavement. Shifting to/from 4L (4X4 low) 1. Bring the vehicle to a speed of 3 mph (5 km/h) or less. 2. Place the transmission in N (Neutral). 3. Move the 4WD control to the desired position. 306


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


The message center will display 4X4 SHIFT IN PROGRESS during the shift. The message center will then display the system mode selected. If any of the above shift conditions are not met, the shift will not occur and the message center will display information guiding the driver through the proper shifting procedures. If SHIFT DELAYED PULL FORWARD is displayed in the message center, transfer case gear tooth blockage is present. To alleviate this condition, place the transmission in a forward gear, move the vehicle forward approximately 5 feet (1.5 m), and shift the transmission back to neutral to allow the transfer case to complete the range shift. Note: Some noise may be heard as the system shifts or engages; this is normal. Note: 4x4 low mode is not intended for use on dry pavement.


Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Your vehicle may be equipped with a long front air dam that may become damaged (due to reduced ground clearance) when taking your vehicle off-road. This air dam can either be removed or a shorter air dam can be purchased from your authorized dealer. In either case, if the air dam is to be removed (or replaced) before going off-road, refer to the Workshop Manual for the procedure or have your authorized dealer perform the work for you. How your vehicle differs from other vehicles Truck and utility vehicles can differ from some other vehicles. Your vehicle may be higher to allow it to travel over rough terrain without getting hung up or damaging underbody components. The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.


307


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. To maintain steering and braking control of your vehicle, you must have all four wheels on the ground and they must be rolling, not sliding or spinning. Basic operating principles • Do not use 4WD on dry, hard surfaced roads. Doing so will produce


excessive noise, increase tire wear and may damage drive components. 4WD modes are only intended for consistently slippery or loose surfaces.


• Drive slower in strong crosswinds which can affect the normal steering • Be extremely careful when driving on pavement made slippery by


characteristics of your vehicle.


loose sand, water, gravel, snow or ice.


If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.


• It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.


• It often may be less risky to strike small objects, such as highway


reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or roll over. Remember, your safety and the safety of others should be your primary concern.


WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.


308


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


If your vehicle gets stuck If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. If your vehicle is severely stuck, it may need to be pulled out. Front tow/recovery hooks can be used to recover a vehicle struck in the mud or snow. Refer to Recovery hooks in the Tires, Wheels and Loading chapter for more information. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat.


WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander.


Refer to Gauges in the Instrument Cluster chapter for transmission fluid temperature information. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control, not more. Additionally, smooth variations of the accelerator and/or brake pedal pressure should be utilized if changes in vehicle speed are called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surface to return the vehicle to a safe direction of travel.


• In the event of an emergency stop, avoid skidding the tires and do not


attempt any sharp steering wheel movements.


309


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. • If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs.


Parking On some 4WD vehicles, when the transfer case is in the N (Neutral) position, the engine and transmission are disconnected from the rest of the driveline. Therefore, the vehicle is free to roll even if the automatic transmission is in P (Park). Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle.


WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off


position and remove the key whenever you leave your vehicle.


WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be


working properly. See your authorized dealer.


4WD systems 4WD (when you select a 4WD mode), uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Power is supplied to all four wheels through a transfer case. On 4WD vehicles, the transfer case allows you to select 4WD when necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance 310


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


can be found in the Maintenance and Specifications chapter. You should become thoroughly familiar with this information before you operate your vehicle. Normal characteristics On some 4WD models, the initial shift from two-wheel drive to 4x4 while the vehicle is moving can cause some momentary clunk and ratcheting sounds. This is the front drivetrain coming up to speed and the automatic locking hubs engaging and is not cause for concern. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Avoid excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Note: If air is released from your tires, the Tire Pressure Monitoring System (TPMS) indicator light may illuminate (if equipped). Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even 4WD vehicles can lose traction in slick mud. As when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels. If the vehicle does slide, steer in the direction of the slide until you regain control of the vehicle. If the transmission, transfer case or front axle are submerged in water, their fluids should be checked and changed, if necessary.


311


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Driving through deep water may damage the transmission. Refer to Transmission temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information. If the front or rear axle is submerged in water, the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components. “Tread Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.” Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer.


312


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. If you do stall out, do not try to turn around because you might roll over. It is better to back down to a safe location. Apply just enough power to the wheels to climb the hill. Too much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control. Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, manually shift to a lower gear. Your vehicle has anti-lock brakes, apply the brakes steadily. Do not “pump” the brakes.


Driving on snow and ice 4WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. Avoid sudden braking as well. Although a 4WD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster, because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions.


313


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, avoid locking of the wheels. Use a “squeeze” technique, push on the brake pedal with a steadily increasing force which allows the wheels to brake yet continue to roll so that you may steer in the direction you want to travel. If you lock the wheels, release the brake pedal and repeat the squeeze technique. If your vehicle is equipped with a Four Wheel Anti-Lock Brake System (ABS), apply the brake steadily. Do not “pump” the brakes. Refer to the Brakes section of this chapter for additional information on the operation of the anti-lock brake system.


WARNING: If you are driving in slippery conditions that require tire cables, then it is critical that you drive cautiously. Keep


speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death. If the rear end of the vehicle slides while cornering, steer in the direction of the slide until you regain control of the vehicle.


Maintenance and modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability. For this reason, Ford Motor Company strongly recommends that you do not make modifications such as adding or removing parts (such as lift kits or stabilizer bars) or by using replacement parts not equivalent to the original factory equipment. Any modifications to a vehicle that raise the center of gravity can make it more likely the vehicle will roll over as a result of a loss of control. Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover). Failure to maintain your vehicle properly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety. Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off-road usage.


314


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


VEHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off, or PTO, is often added to the engine or transmission to operate utility equipment. Examples include a wheel-lift for tow trucks, cranes, tools for construction or tire service, and pumping fluids. PTO applications draw auxiliary horsepower from the powertrain, often while the vehicle is stationary. In this condition, there is limited cooling air flow through the radiator and around the vehicle that normally occurs when a vehicle is moving. The aftermarket PTO system installer, having the most knowledge of the final application, is responsible for determining whether additional chassis heat protection or powertrain cooling is required, and alerting the user to the safe and proper operation. Ford Super Duty Vehicles are approved for use as a stationary (including split shaft capability) or mobile power source, within limits and operating guidelines detailed in the Ford Truck Body Builders Layout Book, found at www.fleet.ford.com/truckbbas, and through the Ford Truck Body Builders Advisory Service.


DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).


When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the water, always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. Wet brakes do not stop the vehicle as quickly as dry brakes.


315


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


SNOWPLOWING Ford recommends that the Super Duty F-Series used for snow removal include the Snow Plow Package Option.


Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow can be found in the Ford Truck Body Builders Layout Book, Snowplow section, found at www.fleet.ford.com/truckbbas. A typical installation affects the following: • Certification to government safety laws such as occupant protection and airbag deployment, braking, and lighting. Look for an “Alterer’s Label” on the vehicle from the snowplow installer certifying that the installation meets all applicable Federal Motor Vehicle Safety Standards (FMVSS).


• The Total Accessory Reserve Capacity (TARC) is shown on the lower right side of the vehicle’s Safety Compliance Certification Label. This applies to Ford-completed vehicles of 10,000 lb. (4,536 kg) GVWR or less. This is the weight of permanently-attached auxiliary equipment, such as snowplow frame-mounting hardware, that can be added to the vehicle and satisfy Ford compliance certification to FMVSS. Exceeding this weight may require the auxiliary equipment installer additional safety certification responsibility. The Front Accessory Reserve Capacity (FARC) is added for customer convenience.


• Rear ballast weight behind the rear axle may be required to prevent exceeding the FGAWR, and provide front-to-rear weight balance for proper braking and steering.


• Front wheel toe may require re-adjustment to prevent premature uneven tire wear. Specifications are found in the Ford Workshop Manual.


• Headlight aim may require re-adjustment. • The tire air pressures recommended for general driving are found on the vehicle’s Safety Certification Label. The maximum cold inflation pressure for the tire and associated load rating is imprinted on the tire sidewall. Tire air pressure may require re-adjustment within these pressure limits to accommodate the additional weight of the snowplow installation.


• Federal and some local regulations require additional exterior lamps for snowplow-equipped vehicles. Consult your authorized dealer for additional information.


316


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


Operating the vehicle with the snowplow attached Do not use your vehicle for snow removal until it has been driven at least 500 miles (800 km). The attached snowplow blade restricts airflow to the radiator, and may cause the engine to run at a higher temperature: Attention to engine temperature is especially important when outside temperatures are above freezing. Angle the blade to maximize airflow to the radiator and monitor engine temperature to determine whether a left or right angle provides the best performance. Follow the severe duty schedule in your scheduled maintenance information for engine oil and transmission fluid change intervals.


Snowplowing with your airbag-equipped vehicle Your vehicle is equipped with a driver and passenger airbag Supplemental Restraint System (SRS) The SRS is designed to activate in certain frontal and offset frontal collisions when the vehicle sustains sufficient longitudinal deceleration. Careless or high speed driving while plowing snow which results in sufficient vehicle decelerations can deploy the airbag. Such driving also increases the risk of accidents.


WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air


bag supplemental restraint system (SRS) is provided.


Never remove or defeat the “tripping mechanisms” designed into the snow removal equipment by its manufacturer. Doing so may cause damage to the vehicle and the snow removal equipment as well as possible airbag deployment.


WARNING: Do not attempt to service, repair, or modify the air bag supplemental restraint system (SRS) or its fuses. See your


Ford or Lincoln Mercury dealer.


WARNING: Additional equipment such as snowplow equipment may effect the performance of the airbag sensors increasing the


risk of injury. Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment.


317


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Driving


speeds below 5 mph (8 km/h).


Transmission operation while plowing Operate the vehicle with the automatic transmission gearshift lever in the D (Overdrive) position and tow/haul off. • Shift transfer case to 4L (4x4 Low) when plowing in small areas at • Shift transfer case to 4H (4x4 High) when plowing larger areas or light • Do not shift the transmission from a forward gear to R (Reverse) until • If the vehicle is stuck, shift the transmission in a steady motion


snow at higher speeds. Do not exceed 15 mph (24 km/h).


the engine is at idle and the wheels are stopped.


between forward and reverse gears. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat.


Do not rock the vehicle if the engine is not at normal operating temperature. Do not rock the vehicle for more than a minute. The transmission and tires may be damaged or the engine may overheat. Refer to Gauges in the Instrument Cluster chapter for transmission fluid temperature information.


WARNING: Do not spin the wheels at over 35 mph (55 km/h). The tires may fail and injure a passenger or bystander.


318


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


ROADSIDE ASSISTANCE


Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24-hours, seven days a week • for the coverage period listed on the Roadside Assistance Card


included in your Owner manual portfolio.


responsibility).


supplied with a tire inflation kit).


Roadside assistance will cover: • a flat tire change with a good spare (except vehicles that have been • battery jump start. • lock-out assistance (key replacement cost is the customer’s • fuel delivery – Independent Service Contractors, if not prohibited by state, local or municipal law shall deliver up to 2.0 gallons (7.5L) of gasoline or 5.0 gallons (18.9L) of diesel fuel to a disabled vehicle. Fuel delivery service is limited to two no-charge occurrences within a 12-month period. • winch out – available within 100 feet (30.5 meters) of a paved or • towing – Ford and Lincoln eligible vehicles towed to an authorized dealer within 35 miles (56 km) of the disablement location or to the nearest authorized dealer. If a member requests to be towed to an authorized dealer more than 35 miles (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 miles (56 km).


county maintained road, no recoveries.


Trailers shall be covered up to $200 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services.


Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is found in the owner’s information portfolio in the glove compartment.


319


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


U.S. Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 km). To obtain reimbursement information, U.S. Ford vehicle customers call 1-800-241-3673. Customers will be asked to submit their original receipts.


Vehicles sold in Canada : Getting roadside assistance Canadian customers who require roadside assistance, call 1–800–665–2006.


Vehicles sold in Canada : Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In Canada, the card is found in the Warranty Guide in the glove box. Canadian Roadside coverage and benefits may differ from the U.S. coverage. Please refer to your Warranty Guide or visit our website at www.ford.ca for information on Canadian services and benefits. Canadian customers who need to obtain roadside information, call 1-800-665-2006 or visit our website at www.ford.ca.


HAZARD FLASHER CONTROL Note: With extended use, the flasher may run down your battery. The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. • Press the flasher control and all front and rear direction signals flash. • Press the flasher control again to


turn them off.


Use it when your vehicle is disabled and is creating a safety hazard for other motorists. 320


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you may restart your vehicle by doing the following: 1. Turn the ignition switch to the off position and wait 10 seconds. 2. Turn the ignition switch to the on position. 3. Repeat steps 1 and 2 to re-enable fuel pump. Note: For vehicles equipped with a diesel engine, see the Diesel supplement for additional Fuel Pump Shut-off reset instructions.


WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision.


FUSES AND RELAYS


Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.


15


321


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


Standard fuse amperage rating and color


COLOR


Fuse rating


2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A


Mini fuses


Grey Violet Pink Tan


Brown


Red Blue Yellow Natural Green


— — — — —


Standard


fuses


Grey Violet Pink Tan


Brown


Red Blue Yellow Natural Green


— — — — —


Maxi fuses


Cartridge


maxi fuses


Fuse link cartridge


— — — — — — —


Yellow



Green Orange


Red Blue Tan


Natural


— — — — — — — Blue


— — — — — — — Blue


Natural


Natural


Pink Green Red Yellow



Black


Pink Green Red Yellow Brown Black


Passenger compartment fuse panel The fuse panel is located in the passenger’s footwell. Remove the panel cover to access the fuses.


322


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


To remove the fuse panel cover, pull the panel toward you. When the clips of the panel disengage, let the panel fall easily.


To remove a fuse use the fuse puller tool provided on the fuse panel cover.


WARNING: Always disconnect the battery before servicing high current fuses.


Always replace the cover to the passenger compartment fuse panel before reconnecting the battery. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.


323


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


10


11


12


13


14


15


16


17


18


19


20


21


49


22


23


24


25


26


27


28


29


30


31


32


33


34


35


36


37


38


39


48


40


41


42


43


44


45


46


47


The fuses are coded as follows.


Fuse/Relay Location


Fuse Amp


Rating


10


11


324


30A 15A 30A 10A 20A 5A 7.5A


10A 10A 10A


10A


Protected Circuits


Not used (spare) Upfitter relay #4
Not used (spare) Interior lights, Hood lamp Moon roof Driver seat module Driver seat switch, Driver lumbar motor Power mirror switch Upfitter relay #3
Run/accessory relay, Customer access feed Instrument cluster


2012 F-250/350/450/550 (f23) Owners Guide, 4th Printing USA (fus)


Roadside Emergencies


Fuse/Relay Location


Fuse Amp


Rating

Loading...
x