2001 Ford F 250 Owners Manual

ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes.

AM

FM

AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. AM/FM select in CD or CD changer mode (if equipped) Press this control to stop CD play and begin radio play. Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press

to move to the next

frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.

• Press

to move to the next

frequency up the band (whether or not a listenable station is located there). Hold for quick movement.

47

Controls and features

Tune adjust for CD changer (if equipped) • Press

to select the previous

disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs.

• Press

to select the next disc in the CD changer. Hold the control

to fast-forward through the remaining discs.

Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode • Press

to find the next listenable station down the frequency band.

to find the next

listenable station up the frequency band.

• Press

Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD or CD changer (if equipped) • Press

to seek to the previous

track of the current disc. If a selection has been playing for three seconds or more and you , the CD changer will press replay that selection from the beginning.

• Press

to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.

48

Controls and features

Scan function The scan function works in radio, tape or CD mode.

SCAN

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again. Scan function in CD or CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station.

AM

FM

REW

FF

SIDE 1-2

COMP

SHUFFLE

3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.

49

Controls and features

AUTO

Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner as your original presets. To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: • to decrease the bass output •

to increase the bass output.

CLK

BASS

TREB

and

SEL

50

Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: • to decrease the treble output •

to increase the treble output.

and

Controls and features

BASS

TREB

SEL

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • •

to shift sound to the left and to shift sound to the right.

BAL

FADE

SEL

51

Controls and features

Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: • •

to shift the sound to the

to shift the sound to the rear.

front and

BAL

FADE

SEL

Tape/CD select • To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.

• To begin CD play (if CD(s) are loaded), press the CD control. The first track of the disc will begin playing. If returning from radio or tape mode, CD play will begin where it stopped last.

TAPE

TAPE

CD

CD

With the dual media audio system, press the CD control to toggle between single CD and CD changer play (if equipped). Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

52

continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the

Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will

current track.

Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached.

Controls and features

REW

FF

• In CD mode, pressing the control fast forwards the CD within the

current track.

Tape direction select Press SIDE 1–2 to play the alternate side of a tape.

Eject function Press the EJ control to stop and eject a tape.

Press the EJ control to stop and eject a CD.

SIDE 1-2

EJ

EJ

53

Controls and features

control to activate (and deactivate) the Dolby威 noise

are registered trademarks of Dolby威 Laboratories Licensing

Dolby姞 noise reduction Dolby威 noise reduction operates in tape mode. Dolby威 noise reduction reduces the amount of hiss and static during tape playback. Press the reduction. Dolby威 noise reduction is manufactured under license from Dolby威 Laboratories Licensing Corporation. “Dolby威” and the double-D symbol Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD mode (if equipped) and plays all tracks on the current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks on the current disc are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again.

COMP

SHUFFLE

54

Controls and features

AUTO

CLK

SEEK

TUNE

SEEK

TUNE

AUTO

CLK

SEEK

TUNE

SEEK

TUNE

Setting the clock To set the hour, press and hold the CLK control and press SEEK:

• •

to decrease hours and to increase hours.

To set the minute, press and hold the CLK control and press TUNE:

to decrease minutes and to increase minutes.

• • If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner.

55

Controls and features

AUTO

The CLK button will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10
seconds, when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for 10 seconds before reverting back to the clock. In media mode, the media information will always be displayed. Mute mode Press the MUTE control to mute the playing media. Press the MUTE control again to return to the playing media.

CLK

EJ

MUTE

Premium AM/FM Stereo In Dash Six CD Radio

SHUF

SCAN

DISC TUNE

SEEK

REW

FF

COMP

MUTE

EJ

BASS

BAL

SEL

TREB

FADE

MENU

LOAD

PUSH ON

AM FM

CD

56

Controls and features

PUSH ON

Volume/power control Press the control to turn the audio system on or off.

Turn the control to raise or lower volume.

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes.

AM FM

CD

AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Tune adjust The tune control works in radio or CD mode.

57

Controls and features

Tune adjust in radio mode • Press

to move to the next

frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.

• Press

to move to the next frequency up the band (whether or not

a listenable station is located there). Hold for quick movement.

Tune adjust for CD mode • Press

to select the previous disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs.

• Press

through the remaining discs.

to select the next disc. Hold the control to fast-forward

Seek function The seek function works in radio or CD mode. Seek function in radio mode • Press

to find the next listenable station down the frequency band. SEEK DOWN will display.

• Press

SEEK UP will display.

to find the next listenable station up the frequency band.

58

Controls and features

Seek function in CD mode • Press

to seek to the previous

track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing.

• Press

to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.

Scan function The scan function works in radio or CD mode.

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Press the AM/FM control to toggle between AM, FM1, or FM2. 2. Press the SEEK control to access the next listenable station up or down the frequency band. Press the TUNE control to go up or down the listening band in individual increments. 3. Select a station. Refer to Seek function for more information on selecting a station.

59

Controls and features

4. Press and hold a memory preset control. The playing media will mute momentarily. When the sound returns, the station is held in memory on the control you selected. The display will read SAVED.

Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display as the frequency band is scrolled through. 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the AM/FM control again.

AM FM

CD

60

Controls and features

CD select CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. If an alternative CD is desired, press the corresponding preset control (1–6) of a loaded CD, or press the TUNE control to access the other loaded CDs. NO CD will display if the CD control is activated when there is not a CD present in the audio system. NO CD will illuminate in the display if the CD control and a present number (that is currently empty) are pressed. The system will play the next available disc. If your vehicle is equipped with a CD changer, pressing the CD control again will allow you to toggle between accessing the multi disc system and the CD changer. The display will read CD or CDDJ. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Display description Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot. Load The load feature allows you to load single CDs into the player internal to the radio.

This six disc CD player is equipped with a CD door. Compact discs should only be inserted into the player after the door has been opened by the player. Do not attempt to force the door open. Compact discs should only be loaded by pressing the LOAD control.

61

Controls and features

Press the LOAD control. (You can choose which slot will be loaded by pressing the desired preset number. If you do not choose a slot, the system will choose the next available one.) Wait until the CD door opens. Load the CD into the player. LOADING CD# is displayed. When the CD has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2. Auto load This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio.

Press and hold the LOAD control until AUTOLOAD # is displayed. The CD door will open. Load the desired disc, one at a time. The CD is loaded into position and the audio system will display CD#. Each time the CD door opens, INSERT CD# is displayed. The door will close and the player will move to the next slot after each disc has been loaded. The process is repeated until all 6 slots are full. The audio system plays the last CD loaded and the display is updated. If some slots are already full and autoload is activated, the system will fill all empty slots. Eject Press the EJ control to stop and eject a CD. You can choose which CD will be ejected by pressing the EJ control and the desired preset number (1–6). For example, to eject CD 2, press the EJ control and then press the preset 2 control. If you do not choose a specific CD, the player will eject the current CD. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF. Auto eject Press and momentarily hold the EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF.

62

Controls and features

Rewind The rewind control works in CD modes. Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode. When in rewind mode, your audio system will automatically lower the volume level of the playing media. Fast forward The fast forward control works in CD modes. Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track on the first disc. Release the control to disengage fast forward mode. When in fast forward mode, your audio system will automatically lower the volume level of the playing media. Shuffle feature Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode. When engaged, the shuffle feature has two different modes: SHUFFLE DISC and SHUFFLE TRK. SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system. SHUFFLE TRK plays all the tracks on the current disc in random order. Compression feature (if equipped) The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistent listening level.

MENU

SEL

63

Controls and features

SEL

TREB

BASS

On Audiophile audios, press the MENU control until compression status is displayed. Press the SEL control to enable the compression feature when COMP OFF is displayed. Press the SEL control again to disable the feature when COMP ON is displayed. On Premium audios, press the COMP control until COMP ON is displayed. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.

BASS

FADE

FADE

TREB

BAL

BAL

SEL

SEL

SEL

64

Controls and features

Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available. If RDS is turned OFF, you can access the following: • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES — Refer to Setting the clock. • RDS OFF — Refer to Radio data system feature. If RDS is turned ON, you can access the following: • TRAFFIC ON/OFF-Refer to Traffic announcements. • FIND type-Refer to Program type. • SHOW (NAME, TYPE, NONE)- Refer to Radio data system feature. • RDS ON— Refer to Radio data system feature. • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES —Refer to Setting the clock. When in CD mode, you can access: SELECT HOURS, SELECT MINUTES or COMP ON/OFF. SELECT HOURS, SELECT MINUTES— Allows you to adjust the hours and minutes. Refer to Setting the clock. TRAFFIC ON/OFF— Traffic announcements can be programmed as local or distant. Refer to Traffic announcements. RDS ON/OFF— This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Refer to Radio Data System feature. FIND type — Allows you to select your desired FM program type and search for that selection. SHOW — Allows you to select from NAME (displays the name of the radio station), TYPE (displays the RDS program type: rock, jazz, etc.), or NONE (deactivates the RDS display).

65

Controls and features

SEL

MENU

Radio data system (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections: Traffic announcements This feature allows you to hear traffic announcements while in CD mode. These announcements are broadcast by traffic capable RDS stations. When in this mode, traffic announcements will interrupt radio and CD play. • Press the MENU control until TRAFFIC is displayed. • Press the SEL control to engage the feature. The display will read

TRAFFIC ON.

This feature also allows you to control the volume of traffic announcements. With the display reading TRAFFIC ON, adjust the volume using the volume control to the desired level. The volume level will show at the bottom of the display. Interrupting traffic announcements will be at the selected volume level. To disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF. Traffic announcements not available in most U.S. markets.

66

Controls and features

SEL

MENU

Program type This feature allows you to search for RDS stations selectively by their program type. Press the MENU control until FIND program type is displayed. Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R & B • Religious • Rock • Soft • Top 40
Show This feature allows you to select the type of RDS broadcast information the radio will regularly show in the display.

MENU

SEL

With RDS activated, press the MENU control until SHOW is displayed. Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display).

MENU

SEL

67

Controls and features

SEL

DSP

Digital signal processing (if equipped) The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes. Press the DSP control to access the DSP menu. Press the SEL control to enter one of the following modes: • DSP OFF • SIGNAL MODE • OCCUPANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: • DSP OFF—disengages the feature • NEWS—”voice-only” type of sound with a limited audio band • JAZZ CLUB—jazz club with clearly reflected sounds • HALL—rectangular concert hall capacity of about 2 000
• CHURCH—church with a high vault • STADIUM—outdoor stadium with a capacity of about 30 000
Press the DSP control again to access the occupancy modes. Use the SEL control to optimize the sound based upon the occupants in the vehicle. The following occupancy modes can be selected: • ALL SEATS • DRIVER SEAT • REAR SEATS

SEL

68

Controls and features

will mute.

number previously programmed in the phone.

Phone mode This feature allows you to control the factory-installed cellular phone (if equipped) through the radio controls. • Press the phone/mute control to enter phone mode. The playing media • Use SEEK, TUNE or radio presets 1 through 6 to select a phone • Press the phone/mute control again to send and end calls. This control will mute the playing media even if your vehicle is not equipped with a factory-installed cellular phone. Press the control again to return to the playing media. Setting the clock Press the MENU control until SELECT HOUR or SELECT MINUTE is displayed. Use the SEL control to manually set the time. • Press • Press

hours/minutes.

to decrease

to increase

SEL

hours/minutes.

Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion.

CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended • Do not insert more than one disc into each slot of the CD changer

periods of time.

magazine.

69

Controls and features

Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation.

Cassette and cassette player care • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity, extreme heat or

extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. • Tighten very loose tapes by inserting a finger or pencil into the hole • Remove loose labels before inserting tapes. • Do not leave tapes in the cassette player for a long time when not

and turning the hub.

being played.

Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: • AM 530, 540–1600, 1610 kHza • FM 87.9b, 88.1–107.7, 107.9 MHz Not all frequencies are used in a given area. aSome radios may tune up to 1710 kHz. bSome radios may tune down to 87.7 MHz. Radio reception factors Three factors can affect radio reception: • Distance/strength.The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.

70

Controls and features

• Terrain.Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.

• Station overload.Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.

The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.

Audio system warranties and service Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or a qualified technician.

POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine. Release the key as soon as the engine starts.

71

Controls and features

TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn

turn signal.

signal.

SPEED CONTROL (IF EQUIPPED)

To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.

Do not use the speed control in heavy traffic or

on roads that are winding, slippery, or unpaved.

ON

OFF

72

Controls and features

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased.

To set a speed • Press SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).

ON

OFF

RES

SET

ACCEL

COAST

If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES will re-engage it.

Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.

73

Controls and features

To set a higher set speed • Press and hold SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET ACCEL to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET ACCEL.

RES

SET

ACCEL

COAST

You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.

To set a lower set speed • Press and hold COAST. Release

the control when the desired speed is reached or • Press and release COAST to

operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or

• Depress the brake pedal. When

the desired vehicle speed is reached, press SET ACCEL.

74

RES

SET

ACCEL

COAST

RES

SET

ACCEL

COAST

Controls and features

To disengage speed control • Depress the brake pedal or

• Depress the clutch pedal

(if equipped).

Disengaging the speed control will not erase the previously programmed set speed.

Pressing OFF will erase the previously programmed set speed.

ON

OFF

75

Controls and features

To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph).

RES

SET

ACCEL

COAST

Indicator light This light comes on when either the SET ACCEL or RES controls are pressed. The vehicle speed must be at or above 48 km/h (30 mph). It turns off when the speed control OFF control is pressed, the brake or clutch is applied, or the ignition is turned to the OFF position.

CRUISE

76

Controls and features

TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.

77

Controls and features

Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use.

OVERDRIVE CONTROL (IF EQUIPPED)

Activating overdrive

(Overdrive) is the normal drive position for the best fuel economy.

The overdrive function allows automatic upshifts and downshifts through all available gears.

OVERDRIVE

Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of the gearshift lever. The Transmission Control Indicator Light (TCIL) (the word OFF) will illuminate on the end of the gearshift lever. The transmission will operate in all gears except overdrive. To return to normal overdrive mode, press the Transmission Control Switch again. The TCIL (the word OFF) will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter.

(Overdrive) mode.

OVERDRIVE OFF

78

Controls and features

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the

rocker switch to close.

• Press the bottom portion of the

rocker switch to open.

One touch down • Press AUTO completely down and

release quickly. The driver’s window will open fully. Depress again to stop window operation.

AUTO

AUTO

AUTO

79

Controls and features

Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls.

Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.

POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors.

80

Controls and features

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.

POWER SIDE VIEW MIRRORS (IF EQUIPPED) The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror.

MIRRORS L R

81

Controls and features

2. Move the control in the direction you wish to tilt the mirror.

MIRRORS L R

3. Return to the center position to lock mirrors in place. 4. Adjust spotter mirrors (if equipped) manually.

Fold-away mirrors

Fold the side mirrors in carefully when driving through a narrow space, like an automatic car wash. The telescoping feature (if equipped) allows the mirror to extend approximately 76 mm (3 inches).

82

Controls and features

Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, lift the mirror cover open.

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with • Coin holder • Pen holder • Writing surface

cassette/CD holder

83

Controls and features • Utility compartment • Coin holder • Pen holder • Writing surface • Space for lap-top computer

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the LOCK position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.

84

Controls and features

Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors.

Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn will make two quick chirps, reminding you to properly close all doors.

Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Panic alarm will only operate with the ignition in the OFF position.

85

Controls and features

Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together.

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open The battery saver will shut off the interior lamps 45 minutes after the ignition has been turned to the OFF position.

86

Controls and features

Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s

transmitters to your dealer for programming, or

• Perform the programming

procedure yourself

Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Place the key in the ignition and turn from 2 (LOCK) to 3 (OFF) and cycle between 3 (OFF) and 4(ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4 (ON) position. The doors will lock/unlock to confirm that programming mode has been entered.

• Within 20 seconds, program a remote transmitter by pressing any

button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.) • Repeat the previous step to program additional remote transmitters.

The doors will lock/unlock to confirm that each remote transmitter has been programmed. • When you have completed programming the remote transmitters, turn

the ignition to 3 (OFF) or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.

87

Controls and features

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the • Turn ignition key to the left to

right to engage lock.

unlock.

TAILGATE REMOVAL Your tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45 degree angle. 5. Lift right side off of its hinge. 6. Lift left side off of its hinge. To install, follow the removal procedures in reverse order.

88

Seating and safety restraints

SEATING

Full bench seat (if equipped) • Lift the track release bar to move the seat forward or backward. Ensure that the seat is relatched into place.

• Pull up on the release lever located at the bottom of the seatback to quickly fold the seatback forward.

40/20/40 split bench seat (if equipped) • Lift the track release bar to move the seat forward or backward. Ensure the seat is relatched into place. • Pull the seatback handle up to • Push down the release lever located at the bottom of the seatback to quickly fold the seatback forward.

recline the seat.

89

Seating and safety restraints

Captain’s chair (if equipped) • Lift the track release bar to move

the seat forward or rearward. Make sure that the seat is relatched into place.

• Pull the release lever handle

located on the side of the seat up to move the seat back forward or backward. • Push down the release lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward.

Adjusting the front power seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision.

The control is located on the outboard side of the seat cushion.

90

Seating and safety restraints

Press to raise or lower the front portion of the seat cushion.

Press to raise or lower the rear portion of the seat cushion.

Press the control to move the seat forward, backward, up or down.

Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.

91

Seating and safety restraints

Heated seats (if equipped) To operate the heated seats: • Push control to activate. • Push again to deactivate.

The indicator light on the control will illuminate when activated.

FOLDING UP THE REAR SEATS (IF EQUIPPED — SUPERCAB ONLY) The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position. 1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position.

92

Seating and safety restraints

RETURNING THE SEAT TO SEATING POSITION

Always be sure that the seat is in a latched position, whether the seat is occupied or empty. If not latched, the seat may cause

injury during a sudden stop.

1. Pull control on the side of the seat to release seat cushion from storage position. 2. Push seat cushion down until it locks into horizontal position.

SAFETY RESTRAINTS

Safety restraints precautions

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is

provided.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas

are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.

93

Seating and safety restraints

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that

are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

2. To unfasten, push the release button and remove the tongue from the buckle.

94

Seating and safety restraints

The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below:

Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. On SuperCab and CrewCab models, the front seat belt system can also be made to lock manually by quickly pulling on the shoulder belt. Rear seat belts (if equipped) cannot be made to lock up by pulling quickly on the belt.

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter.

95

Seating and safety restraints

How to use the automatic locking mode • Buckle the combination lap and

shoulder belt.

• Grasp the shoulder portion and pull downward until the entire belt is extracted.

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

96

Seating and safety restraints

How to disengage the automatic locking mode

Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that

the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual.

Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.

Energy Management Feature • This vehicle has a seat belt system with an energy management

feature at the front outboard seating position to help further reduce the risk of injury in the event of a head-on collision. • The front outboard seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.

97

Seating and safety restraints

Safety belt replacement label The short plastic boot on the front safety belt at the passenger outboard anchor location covers a “Replace Belt” label on the safety belt.

In the event of a collision, the colored label (REPLACE BELT) may become visible. If this occurs, the safety belt must be replaced.

Whenever the yellow portion of the label is

visible, the safety belt must be replaced.

98

Seating and safety restraints

Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury.

Safety belt pretensioner Your vehicle may be equipped with safety belt pretensioners at the driver and front outboard passenger seating positions. The Seat Integrated Restraints (SIR) seat is equipped with a buckle pretensioner. Do NOT place objects between the seats, this could interfere with the functioning of the pretensioner. For the SuperCab and CrewCab base bench seats and all Regular Cab seating positions, the seatbelts are equipped with a retractor pretensioner. The safety belt pretensioners are designed to activate only during certain frontal or near-frontal collisions with sufficient longitudinal deceleration. A safety belt pretensioner is a device which tightens the webbing of the lap and shoulder belts in such a way that they fit more snugly against the body. The driver and front outboard passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in the activation of the safety belt pretensioners. Refer to the Safety belt maintenance section in this chapter.

Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of

a collision.

Front safety belt height adjustment If your vehicle has seat integrated restraints you will not have safety belt height adjustments. Your vehicle may have safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.

99

Seating and safety restraints • Regular Cab and 4–door CrewCab

• 4–door Super Cab (if equipped)

100

Seating and safety restraints

To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.

Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety

belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.

Lap belts Adjusting the center lap belt The lap belt does not adjust automatically.

The lap belt should fit snugly and as low as possible around the hips, not across the waist.

Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.

101

Seating and safety restraints

Shorten and fasten the belt when not in use.

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8
inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso.

Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.

Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position...

The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...

Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8
seconds. The safety belt warning light and warning chime turn off.

The safety belt warning light and indicator chime remain off.

102

Seating and safety restraints

Belt minder The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. If... The driver’s safety belt is not buckled before the vehicle has reached at least 5 km/h (3 mph) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...

Then... The Belt Minder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled. The Belt Minder feature will not activate.

The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... The purpose of the Belt Minder is to remind occasional wearers to wear safety belts all of the time.

The Belt Minder feature will not activate.

103

Seating and safety restraints

The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data)

Reasons given... Consider... “Crashes are rare events”

36 700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 miles of home. “Belts are uncomfortable”

We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.

“I was in a hurry” Prime time for an accident. Belt Minder reminds

“Seat belts don’t work”

“Traffic is light”

“Belts wrinkle my clothes”

“The people I’m with don’t wear belts”

us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.

“I have an air bag” Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40
times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.

“I’d rather be thrown clear”

Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of

injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.

104

Seating and safety restraints

One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure. The Belt Minder feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set. • The gearshift is in P (Park) (automatic transmission) or the neutral • The ignition switch is in the OFF position. • All vehicle doors are closed. • The driver’s safety belt is unbuckled. • The parklamps/headlamps are in OFF position (If vehicle is equipped

position (manual transmission).

with Autolamps, this will not affect the procedure).

To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle.

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2
minutes.) • Steps 3–5 must be completed within 60 seconds or the procedure will

have to be repeated.

3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during Belt Minder warning activation. 4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps. 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.

105

Seating and safety restraints • After step 5 the safety belt warning light will be turned on for three

seconds.

6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt

Minder if it is currently disabled.

7. Confirmation of disabling Belt Minder is provided by the safety belt warning light flashing four times per second for three seconds. 8. Confirmation of enabling Belt Minder is provided by: • The safety belt warning light flashing four times per second for three • Followed by three seconds with the safety belt warning light off. • Once again, the safety belt warning light will flash four times per

seconds.

second for three seconds.

9. After receiving confirmation, the deactivation/activation procedure is complete.

Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe

personal injuries in the event of a collision.

Refer to Cleaning and maintaining the safety belts in the Maintenacne and Care section.

106

Seating and safety restraints

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

50 60

40

70

120

80

140

90

160

km/h

100

18

30

60

80

100

40

20

20

10

MPH

ON

OFF

VOL - PUSH ON

DIESEL FUEL ONLY

RPM x 1000

RES

SET

ACCEL

COAST

AM FM

BASS

TREB