2015 Ford F 150 Owners Manual

•

Note: Do not clean the mirror housing or glass with harsh abrasives, fuel or other petroleum-based cleaning products. CABIN AIR FILTER Your vehicle is equipped with a cabin air filter, which gives you and your passengers the following benefits: •

It improves your driving comfort by reducing particle concentration. It improves the interior compartment cleanliness. It protects the climate control components from particle deposits. You can locate the cabin air filter behind the glove box. Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. Replace the filter at regular intervals. See Scheduled Maintenance (page 498).

•

HEATED WINDOWS AND MIRRORS (If Equipped) Heated Rear Window Note: Make sure the engine is running before operating the heated windows. Press the button to clear the heated rear window of thin ice and fog. The heated rear window

will automatically turn off after a short period of time. Start the engine before you switch the heated rear window on. Note: Do not use razor blades or other sharp objects to clean or remove decals from the inside of the heated rear window. The vehicle warranty does not cover damage caused to the heated rear window grid lines. Heated Exterior Mirror When you switch the heated rear window on, the heated exterior mirrors will automatically turn on. Note: Do not remove ice from the mirrors with a scraper or adjust the mirror glass when it is frozen in place.

137

F-150 (TFC), enUSA, Third Printing

E184884Climate Control

For additional cabin air filter information, or to replace the filter, see an authorized dealer. REMOTE START (If Equipped) The remote start feature allows you to pre-condition the interior of your vehicle. The climate control system works to achieve comfort according to your previous settings. Note: You cannot adjust the system during remote start operation. Turn the ignition on to return the system to its previous settings. You can now make adjustments normally, but you need to turn certain vehicle-dependent features back on, such as: • Heated seats. • Cooled seats. • Heated steering wheel. • Heated mirrors. • Heated rear window. You can adjust the default remote start settings using the information display controls. See Information Displays (page 103). Automatic Settings In hot weather, the system is set to 72°F (22°C). The cooled seats are set to high (if available, and selected to AUTO in the information display). In moderate weather, the system either heats or cools (based on previous settings). The rear defroster, heated mirrors and heated seats do not automatically turn on. In cold weather, the system is set to 72°F (22°C). The heated seats are set to high (if available, and selected to AUTO in the information display). The rear defroster and heated mirrors automatically turn on.

138

F-150 (TFC), enUSA, Third Printing

Seats

SITTING IN THE CORRECT POSITION

WARNINGS

Sitting improperly, out of position or with the seatback reclined too far can take weight off the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in the event of a crash. Always sit upright against your seat back, with your feet on the floor.

Do not recline the seatback as this can cause the occupant to slide under the safety belt, resulting in

serious injury in the event of a crash.

Do not place objects higher than the seatback to reduce the risk of serious injury in the event of a crash or during

heavy braking.

When you use them properly, the seat, head restraint, safety belt and airbags will provide optimum protection in the event of a crash.

F-150 (TFC), enUSA, Third Printing

We recommend that you follow these guidelines: •

Sit in an upright position with the base of your spine as far back as possible.

• Do not recline the seatback more than

30 degrees.

• Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 in (25 cm) between your breastbone and the airbag cover.

•

• Hold the steering wheel with your arms

slightly bent. Bend your legs slightly so that you can press the pedals fully.

•

• Position the shoulder strap of the safety belt over the center of your shoulder and position the lap strap tightly across your hips.

Make sure that your driving position is comfortable and that you can maintain full control of your vehicle. HEAD RESTRAINTS WARNINGS

Fully adjust the head restraint before you sit in or operate your vehicle. This will help minimize the risk of neck

injury in the event of a crash. Do not adjust the head restraint when your vehicle is moving.

The head restraint is a safety device. Whenever possible it should be installed and properly adjusted when

the seat is occupied. An improperly adjusted head restraint may not adequately protect an occupant during an impact from the rear.

139

E68595Seats

WARNINGS

Install the head restraint properly to help minimize the risk of neck injury in the event of a crash.

Note: Adjust the seatback to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position. Front Seat Head Restraint

Rear Seat Outboard Head Restraints

Rear Seat Center Head Restraint

The head restraints consist of:

An energy absorbing head restraint. Two steel stems. Guide sleeve adjust and release button. Guide sleeve unlock and remove button. Fold button (rear seat outboard only).

Adjusting the Head Restraint Raising the Head Restraint Pull the head restraint up. Lowering the Head Restraint 1. Press and hold button C. 2. Push the head restraint down. Removing the Head Restraint 1. Pull up the head restraint until it reaches the highest adjustment position.

2. Press and hold buttons C and D. 3. Pull up the head restraint.

140

F-150 (TFC), enUSA, Third Printing

E138642E166700EDCBAE166701ADCBSeats

Note: For rear seat outboard seats, you can fold the head restraint forward for easier removal. Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until it locks. Folding the Head Restraint Note: The rear seat outboard head restraints may fold forward for improved visibility. 1. Press and hold button E. 2. Pull it back up to reset. Front Seat Center Head Restraint Your vehicle may be equipped with a front row center head restraint that you cannot adjust or remove. Tilting Head Restraints (If Equipped) The front head restraints tilt for extra comfort. To tilt the head restraint, do the following:

2. Pivot the head restraint forward toward

your head to the desired position. After the head restraint reaches the forward-most tilt position, pivot it forward again to release it to the rearward, untilted position. Note: Do not attempt to force the head restraint backward after it is tilted. Instead, continue tilting it forward until the head restraint releases to the upright position. MANUAL SEATS

WARNING

Do not adjust the driver's seat or seatback when your vehicle is moving.

Moving the Seat Backward and Forward

1. Adjust the seatback to an upright

driving or riding position.

141

F-150 (TFC), enUSA, Third Printing

E144727E175314Recline Adjustment

Seats

The lumbar support control is located on the outboard side of the seat. Turn the control to adjust your support. POWER SEATS (If Equipped)

WARNINGS

Do not adjust the driver seat or seatback when your vehicle is moving. Adjusting your seatback

while the vehicle is in motion may cause loss of control of the vehicle.

Manual Lumbar (If Equipped)

Do not place cargo or any objects behind the seatback before returning it to the original position.

142

F-150 (TFC), enUSA, Third Printing

E175315E166702Seats

Power Lumbar (If Equipped)

Note: The engine must be running or the vehicle must be in accessory mode to activate the seats. Note: Allow a few seconds for any selection to activate. The seatback and cushion massage cannot function at the same time.

Multi-Contour Front Seats With Active Motion (If Equipped) Note: The massage system will turn off after 20 minutes.

143

F-150 (TFC), enUSA, Third Printing

E176038E176039E156301Seats

Massage mode

Lumbar and bolster mode

Back massage intensity

adjustment

Upper lumbar

Massage intensity decrease

Lumbar decrease

and off1

Cushion massage intensity

adjustment

Lower lumbar2

Massage intensity increase

Lumbar increase

On and off

MEMORY FUNCTION (If Equipped)

WARNINGS

Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of

obstructions and that all occupants are clear of moving parts.

Do not use the memory function when your vehicle is moving.

This function automatically recalls the position of these features: • Driver seat. • Power mirrors. • Adjustable pedals. • The memory control is located on the door panel.

Steering column.

1The massage feature will default to an alternating massage mode with back massage intensity adjustment. The lumbar and bolster feature will default to the middle lumbar mode. 2Press C a second time to adjust the back bolster. Press C a third time to adjust the cushion bolster. You can also adjust this feature through the touchscreen. When switched on, the system displays directions for you to adjust the lumbar settings in your seat or to set the massage function. To access and make adjustments to the lumbar setting: 1. Press the Menu Settings icon > Vehicle

> Multi-contour Seat.

2. Choose the desired seat to adjust. 3. Press the + or - to adjust the lumbar

intensity.

To access and make adjustments to the massage setting: 1. Press the Menu Settings icon > Vehicle

>Multi-contour Seat.

2. Choose the desired seat to adjust. 3. Press Off, Lo or Hi.

144

F-150 (TFC), enUSA, Third Printing

Seats

Easy Entry and Exit Feature (If Equipped) If you enable the easy entry and exit feature, it automatically moves the driver seat rearward 2 inches (5 centimeters) when you switch the ignition off. If the seat is located less than 2 inches (5
centimeters) from the rear of the seat track, the seat travels less than 2 inches (5 centimeters) rearward. The driver seat returns to the previous position when you switch the ignition on. You can enable or disable this feature in the information display. See Information Displays (page 103). REAR SEATS Folding Up the Rear Seat Cushion The rear seat has a split 60/40 cushion. You can flip each seat cushion up into a vertical storage position.

Rotate the seat cushion up until it locks into the vertical storage position.

Saving a PreSet Position 1. Switch the ignition on. 2. Move the memory features to your

desired positions.

3. Press and hold button 1 for about two seconds until you hear a single tone.

To program position 2, repeat the previous procedure using button 2. Note: You can save a memory preset at any time. Recalling a PreSet Position: Press and release the preset memory button desired. The memory features move to the position stored for that preset. You can recall a programmed memory position: • When the ignition is off. • Only if the transmission is in park (P)

or neutral (N) if the ignition is on.

You can program a remote entry transmitter to recall a memory setting. See Keys and Remote Controls (page 51). You can also program a personal keyless entry code to recall a memory setting. See Locks (page 62).

145

F-150 (TFC), enUSA, Third Printing

E142554E181250Seats

Returning the Seat to the Seating Position

WARNING

Make sure that cargo or any objects are not trapped underneath the seat cushion before returning the seat

cushion to its original position, and that the seat cushion locks into place. Failure to do so may prevent the seat from operating properly in the event of a crash, which could increase the risk of serious injury.

Pull the control on the bottom of the seat cushion to release the seat cushion from the storage position.

HEATED SEATS (If Equipped)

WARNING

People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal

cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings.

146

F-150 (TFC), enUSA, Third Printing

E166704E146322Seats

Rear Heated Seats (If Equipped)

WARNING

People who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

The rear seat heat controls are located on the rear of the center console.

Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. The heated seat module resets at every ignition run cycle. While the ignition is in the on position, press the heated seat switch to enable heating mode. When activated, they turn off automatically when you switch off the engine. CLIMATE CONTROLLED SEATS (If Equipped) Heated Seats

WARNING

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Note: Do not do the following: • Place heavy objects on the seat. • Operate the seat heater if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

147

F-150 (TFC), enUSA, Third Printing

E146322Seats

FRONT SEAT ARMREST (If Equipped)

Touch the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. Cooled Seats The cooled seats only function when the engine is running.

Press the release control to move the front seat armrest up or down.

Lift the latch to open the lid and gain access to the optional storage compartment under the center seat cushion. The cupholder is located inside the front seat armrest. You can also flip the cupholder so that it faces forward. See Center Console (page 156).

To operate the cooled seats: Touch the cooled seat symbol to cycle through the various cooling settings and off. More indicator lights indicate cooler settings. If the engine falls below 350 RPM while the cooled seats are on, the feature turns itself off. You need to reactivate it. Climate controlled seat air filter replacement Your vehicle is equipped with lifetime air filters that are integrated with the seats. Regular maintenance or replacement is not needed.

148

F-150 (TFC), enUSA, Third Printing

E146322E146309E175382E184821Seats

REAR SEAT ARMREST (If Equipped)

Pull the strap located on the center seatback to access the armrest and cupholders. The cupholders are located inside the rear seat armrest. To open the cupholders: 1. Push in gently on the center of the

plastic panel on the front edge of the armrest. The cupholders will partially open.

2. Pull the cupholder fully open before

using.

149

F-150 (TFC), enUSA, Third Printing

E181222Universal Garage Door Opener (If Equipped)

HomeLink Wireless Control System

WARNINGS

Make sure that the garage door and security device are free from obstruction when you are

programming. Do not program the system with the vehicle in the garage.

Do not use the system with any garage door opener that does not have the safety stop and reverse

feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982). A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death.

Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. Note: We recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the Function Button Codes later in this section. Note: You can program a maximum of three devices. To change or replace any of the three devices after it has been initially programmed, you must first erase the current settings. See Erasing the Function Button Codes.

The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter integrated into the driver’s sun visor. The system includes two primary features, a garage door opener and a platform for remote activation of devices within the home. You can program garage doors as well as entry gate operators, security systems, entry door locks and home or office lighting. Additional system information can be found online at www.homelink.com, www.youtube.com/user/HomeLinkGentex or by calling the toll-free help line at 1-800-355-3515. In-Vehicle Programming This process is to program your in-vehicle HomeLink function button with your hand-held transmitter. Note: The programming steps below assume you will be programming HomeLink that was not previously programmed. If your HomeLink was previously programmed, you may need to erase your HomeLink buttons. See Erasing the Function Button Codes. Note: Put a new battery in the hand-held transmitter. This helps ensure quicker training and accurate transmission of the radio-frequency signal.

150

F-150 (TFC), enUSA, Third Printing

E188211Universal Garage Door Opener (If Equipped)

If the indicator light flashes rapidly, press and hold for two seconds and release the programmed HomeLink button. Repeat the "press/hold/release" sequence up to three times to complete the programming process. If your device still does not operate, you must program your garage door. See Programming Your Garage Door Opener Motor. To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com, www.youtube.com/user/HomeLinkGentex or by calling the toll-free help line at 1-800-355-3515. Programming Your Garage Door Opener Motor Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener.

1. Press the learn button on the garage

door opener motor and then you have 30 seconds to complete the next two steps.

2. Return to your vehicle.

1. With your vehicle parked outside of the garage, switch your ignition to the on position, but do not start your vehicle. 2. Press and release the function button

that you would like to program.

3. Hold your hand-held garage door

transmitter 1–3 in (2–8 cm) away from the HomeLink button you want to program.

4. Press and hold the hand-held transmitter button you want to program while watching the indicator light on HomeLink. Continue to hold the hand-held button until the HomeLink indicator light flashes rapidly or is continuously on.

Note: You may need to use a different method if you live in Canada or have difficulties programming your gate operator or garage door opener. See Gate Operator / Canadian Programming. 5. Press and hold the HomeLink button you programmed for two seconds, then release. You may need to do this twice to activate the door. If your garage door does not operate, watch the HomeLink indicator light.

If the indicator light stays on, the programming is complete. Your device should activate when the HomeLink button is pressed and released.

151

F-150 (TFC), enUSA, Third Printing

E188212E142659Universal Garage Door Opener (If Equipped)

1. Press and hold the outer two function

buttons simultaneously for approximately 10 seconds until the indicator light above the buttons flashes rapidly.

2. When the indicator light flashes,

release the buttons. You erased the codes for all buttons.

Reprogramming a Single Button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do

NOT release the button.

2. The indicator light begins to flash after

20 seconds. Without releasing the button, follow Step 1 in the Programming section.

For questions or comments, contact HomeLink at www.homelink.com, www.youtube.com/user/HomeLinkGentex or by calling the toll-free help line at 1-800-355-3515.

3. Press and hold the function button you

want to program for 2 seconds, then release. Repeat this step. Depending on your brand of garage door opener, you may need to repeat this sequence a third time.

Gate Operator / Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating. 1. Press and release,every two seconds, your hand-held transmitter until the HomeLink indicator light changes to a rapidly blinking or continuously on light.

2. Release the hand-held transmitter

button.

3. Continue programing HomeLink. See In-Vehicle Programming, Step 4. Erasing the Function Button Codes Note: You cannot erase individual buttons.

152

F-150 (TFC), enUSA, Third Printing

E188212E188213Universal Garage Door Opener (If Equipped)

FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications to your device not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End Users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must be at least 8 in (20 cm) from the user and must not be co-located or operating in conjunction with any other antenna or transmitter. The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.

153

F-150 (TFC), enUSA, Third Printing

Auxiliary Power Points

Locations Power points may be in the following locations: • On the instrument panel. In the front of the center console. • In the 20% seat bin. • • In the center console storage bin. • On the rear of the center console. 110 Volt - 400 Watt Capacity AC Power Outlet

WARNING

Do not keep electrical devices plugged in the power outlet when the devices are not in use. Do not use

any extension cord with the 110 volt AC power outlet, since it will defeat the safety protection design. Do not use a single power outlet to power multiple devices. It may cause the power outlet to exceed the 400 watt load limit and overload, resulting in fire or serious injury.

12 Volt DC Power Point WARNING

Do not plug optional electrical accessories into the cigar lighter socket (if equipped). Improper use

of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury.

Note: If used when the engine is not running, the battery can discharge. There may be insufficient power to restart your engine. Note: Do not insert objects other than an accessory plug into the power point. This damages the outlet and blows the fuse. Note: Do not hang any type of accessory or accessory bracket from the plug. Note: Do not use the power point over the vehicle capacity of 12 volt DC 180 watts or a fuse may blow. Note: Do not use the power point for operating a cigar lighter element. Note: Improper use of the power point can cause damage not covered by your warranty. Note: Always keep the power point caps closed when not in use. Run the engine for full capacity use of the power point. To prevent the battery from being discharged: • Do not use the power point longer than

necessary when the engine is not running.

• Do not leave devices plugged in

overnight or when the vehicle is parked for extended periods.

154

F-150 (TFC), enUSA, Third Printing

E191617Auxiliary Power Points

• Measuring devices which process precise data, for example medical equipment or measuring equipment.

• Other appliances requiring an

extremely stable power supply, for example microcomputer-controlled electric blankets or touch sensor lamps.

Note: This feature works only when the vehicle is running. Note: This feature has a maximum output of 400 watts when the vehicle is in park (P). Note: While in drive (D), the maximum outlet output is 300 watts. Note: When powering electric devices that require more than 10 watts in vehicles equipped with keyless start, the vehicle must remain running. It does not allow you to switch the ignition off or switch the ignition to accessory mode.

When the indicator light, located on the power outlet, is: • On and the light is solid — the power

outlet is available or the plugged in device is within the power range and does not exceed the outlet's power limits. Three flashes and off — the power outlet is overloading.

•

• Off — the power outlet power supply

is off; ignition is not on.

• Constant flashing — the power outlet

is in fault mode, and requires you to restart your vehicle.

Electric hand drills.

The power outlet temporarily turns off power when in fault mode if the device exceeds the 400 watt limit. Unplug your device and switch the ignition off. Switch the ignition back on, but do not plug your device back in. Let the system cool off and switch the ignition off to reset the fault mode. Switch the ignition back on and make sure the indicator light remains on. You can use the 400 watt power outlet for these types of electric devices: • • Rechargeable power tools. • Video games. • • You should not use the 400 watt power outlet for these types of electric devices: • Cathode ray tube type televisions. • Motor loads, for example vacuum cleaners, electric saws and other electric power tools, or compressor-driven refrigerators.

Laptops. Television screens.

155

F-150 (TFC), enUSA, Third Printing

Storage Compartments

CENTER CONSOLE (If Equipped) Stow items in the cup holder carefully as items may become loose during hard braking, acceleration or crashes, including hot drinks which may spill. In vehicles with a 40-20-40 split-bench seat, the cup holders are inside of the folding console.

A. Front cup holders. B. Rear cup holders.

Available console features include: A. B. One of the following:

12 volt DC power point.

• USB ports and SD card slot. • Audio input jack and USB port. • Audio input jack. 12-volt power point and intelligent access transmitter backup slot.

C.

D. Locking storage compartment with

hanging file folder supports and room for a laptop computer.

To use the cup holders: 1. Lift the console lid up to open. 2. Lift the cup holders up and rotate them

outward.

3. Close the console. Vehicles with a console-mounted shifter feature cup holders molded into the console.

156

F-150 (TFC), enUSA, Third Printing

E185121E176222E176223Storage Compartments

110 volt AC power point. 12 volt DC power point.

E. F. OVERHEAD CONSOLE (If Equipped)

Press near the rear edge of the door to open it.

157

F-150 (TFC), enUSA, Third Printing

E75193Starting and Stopping the Engine

GENERAL INFORMATION

IGNITION SWITCH

WARNINGS

Extended idling at high engine speeds can produce very high temperatures in the engine and

exhaust system, creating the risk of fire or other damage.

Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up

the engine compartment and exhaust system, creating the risk of fire.

Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.

If you smell exhaust fumes inside your vehicle, have your vehicle checked by an authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes.

If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period. The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise. When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine.

158

F-150 (TFC), enUSA, Third Printing

A (off) - The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. B (accessory) - Allows the electrical accessories, such as the radio, to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. C (on) - All electrical circuits are operational and the warning lamps and indicators illuminate. D (start) - Cranks the engine. KEYLESS STARTING Note: The keyless starting system may not function if the key is close to metal objects or electronic devices such as cellular phones. Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine.

CDBAE163165Starting and Stopping the Engine

Note: You can crank the engine for a total of 60 seconds (without the engine starting) before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine three times for 20 seconds each time, without the engine starting, you reached the 60-second time limit. A message appears in the information display alerting you that you exceeded the cranking time. You cannot attempt to start the engine for at least 15 minutes. After 15 minutes, you are limited to a 15-second engine cranking time. You need to wait 60 minutes before you can crank the engine for 60 seconds again. Before starting the engine, check the following: • Make sure all occupants have fastened

their safety belts.

• Make sure the headlamps and electrical accessories are off.

• Make sure the parking brake is on. • Move the transmission selector lever

to position P. Turn the ignition key to on. If your vehicle is equipped with a keyless ignition, see the following instructions.

•

Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. If your vehicle is equipped with a manual transmission, fully press the clutch pedal also.

2. Turn the key to start to start the engine. Release the key when the engine starts.

Note: The engine may continue cranking for up to 15 seconds or until it starts. Note: If you cannot start the engine on the first try, wait for a short period and try again.

Ignition Modes

The keyless starting system has three modes: Off: Turns the ignition off. • Without applying the brake pedal, press and release the button once when the ignition is in the on mode, or when the engine is running but the vehicle is not moving.

On: All electrical circuits are operational and the warning lamps and indicators illuminate. • Without applying the brake pedal, press and release the button once.

Start: Starts the vehicle. The engine may not start when the vehicle starts. • Press the brake pedal, and then press the button for any length of time. An indicator light on the button illuminates when then ignition is on and when the engine starts.

STARTING A GASOLINE ENGINE When you start the engine, the idle speed increases. This helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer.

159

F-150 (TFC), enUSA, Third Printing

E144447Starting and Stopping the Engine

2.

If your vehicle is equipped with Type Two, make sure the buttons are facing the rear of the vehicle and the key ring up. Place the key into the backup slot. 3. With the key in this position, press the

brake pedal, and then the button to switch on the engine.

Fast Restart The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. Within 20 seconds of switching the engine off, press the brake pedal and press the button. After 20 seconds have expired, you can no longer restart the engine without the key present inside your vehicle. Once the engine has started, it remains running until you press the button, even if the system does not detect a valid key. If you open and close a door while the engine is running, the system searches for a valid key. You cannot restart the engine if the system does not detect a valid key within 20 seconds. Failure to Start If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure: 1. Fully press the brake pedal. 2. Move the transmission selector lever

to position P.

3. Fully press the accelerator pedal and

hold it there.

4. Start the engine.

Vehicles with Keyless Start Note: Do not touch the accelerator pedal. Note: You must have your intelligent access key in the vehicle in order to shift the transmission out of position P. 1. Fully press the brake pedal. 2. Press the button. The system does not function if: • • If you are unable to start the engine, locate the backup slot (A) in one of two positions: Type One

The key frequencies are jammed. The key battery has no charge.

Type Two

1.

If your vehicle is equipped with Type One, make sure to place the key properly into the backup slot.

160

F-150 (TFC), enUSA, Third Printing

E187576E187577Starting and Stopping the Engine

Stopping the Engine When Your Vehicle is Stationary Vehicles with an Ignition Key 1. Move the transmission selector lever

to position P.

2. Turn the key to off. 3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever

to position P.

2. Press the button once. 3. Apply the parking brake. Note: This switches off the ignition, all electrical circuits, warning lamps and indicators. Note: If the engine is idling for 30 minutes, the ignition and engine automatically shut down. Stopping the Engine When Your Vehicle is Moving

WARNING

Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not lock, but higher effort will be required. When the ignition is switched off, some electrical circuits, including air bags, warning lamps and indicators may also be off. If the ignition was turned off accidentally, you can shift into neutral (N) and re-start the engine.

Vehicles with an Ignition Key 1. Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop.

2. When your vehicle has stopped, move

the transmission selector lever to position P and turn the key to off.

Automatic Engine Shutdown If your vehicle is equipped with a keyless ignition, it has a feature that automatically shuts down the engine if it has been idling for an extended period. The ignition also turns off in order to save battery power. Before the engine shuts down, a message appears in the information display showing a timer counting down from 30 seconds. If you do not intervene within 30 seconds, the engine shuts down. Another message appears in the information display to inform you that the engine has shut down in order to save fuel. Start your vehicle as you normally do. Automatic Engine Shutdown Override Note: You cannot permanently switch off the automatic engine shutdown feature. When you switch it off temporarily, it turns on at the next ignition cycle. You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: •

You can reset the timer by interacting with your vehicle (such as pressing the brake pedal or accelerator pedal). You can temporarily switch off the shutdown feature any time the ignition is on (for the current ignition cycle only). Use the information display to do so. See Information Displays (page 103).

•

• During the countdown before engine shutdown, you are prompted to press OK or RESET (depending on your type of information display) to temporarily switch the feature off (for the current ignition cycle only).

161

F-150 (TFC), enUSA, Third Printing

Starting and Stopping the Engine

3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop.

2. When your vehicle has stopped, move

the transmission selector lever to position P.

3. Press and hold the button for one

second, or press it three times within two seconds.

4. Apply the parking brake. Guarding Against Exhaust Fumes

WARNING

If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and leave the engine idling for long periods, we recommend that you do one of the following: • Open the windows at least 1 in

(2.5 cm). Set your climate control to outside air.

• ENGINE BLOCK HEATER (If Equipped)

WARNINGS

Failure to follow engine block heater instructions could result in property damage or serious personal injury.

162

F-150 (TFC), enUSA, Third Printing

WARNINGS

Do not use your heater with ungrounded electrical systems or two-pronged adapters. There is a risk

of electrical shock.

Do not fully close the hood, or allow it to drop under its own weight when using the engine block heater. This could damage the power cable and may cause an electrical short resulting in fire, injury and property damage.

Note: The heater is most effective when outdoor temperatures are below 0°F (-18°C). The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source. We recommend that you do the following for a safe and correct operation: • Use a 16-gauge outdoor extension cord

that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA). This extension cord must be suitable for use outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard.

• Use as short an extension cord as

possible.

• Do not use multiple extension cords. • Make sure that when in operation, the

extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire.

Starting and Stopping the Engine

• Make sure your vehicle is parked in a

clean area, clear of combustibles.

• Make sure the heater, heater cord and extension cord are firmly connected.

• Check for heat anywhere in the

electrical hookup once the system has been operating for approximately 30
minutes.

• Make sure the system is unplugged and

properly stowed before starting and driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use.

• Make sure the heater system is

checked for proper operation before winter.

Using the Engine Block Heater Make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.0 kilowatt-hours of energy per hour of use. The system does not have a thermostat. It achieves maximum temperature after approximately three hours of operation. Using the heater longer than three hours does not improve system performance and unnecessarily uses electricity.

163

F-150 (TFC), enUSA, Third Printing

Unique Driving Characteristics

AUTO-START-STOP (If Equipped) The system helps reduce fuel consumption by automatically shutting off and restarting the engine while stopped. The engine will restart automatically when you release the brake pedal. In some situations, your vehicle may restart automatically, for example: • • Note: Power assist steering turns off when the engine is off.

To maintain interior comfort. To recharge the battery.

WARNINGS The engine may restart automatically if required by the system. Switch the ignition off before opening the hood or performing any maintenance. Failure to do so may result in serious injuries due to automatic engine restart.

Always switch the ignition off before leaving your vehicle, as the system may have turned the engine off, but the ignition will still be on and automatic restart may occur.

The Auto StartStop system status is available at a glance within the information display. See Information Displays (page 103). Enabling Auto StartStop The system automatically enables every time you start your vehicle if: •

You do not press the Auto StartStop button (not illuminated). Your vehicle exceeds an initial speed of 3 mph (4 km/h) after you have initially started your vehicle. You have stopped your vehicle.

•

•

• •

• • •

• •

•

•

•

•

Your foot is on the brake pedal. The transmission is in drive (D) or Sport mode. The driver door is closed. There is adequate brake vacuum. The interior compartment has cooled or warmed to an acceptable level. The front windshield defroster is off. You have not turned the steering wheel rapidly or you do not have it at a sharp angle. The vehicle is not on a steep road grade. The battery is within optimal operating conditions (battery state of charge and temperature in range). The engine coolant is at operating temperature. Elevation is below about 10000 feet (3048 meters).

You have selected 4X2 or Auto mode. The trailer is not connected. You have not selected Tow haul. You have not selected Manual mode.

• Ambient temperature is moderate. • • • • Note: The system allows multiple successive Auto StartStop events, but it may not operate in conditions of heavy traffic or in extended low speed operation.

The green Auto StartStop indicator light on the instrument cluster will illuminate to indicate

when the automatic engine stop occurs.

If the instrument cluster is equipped with a grey Auto StartStop indicator light, it

illuminates when automatic engine stop is not available due to one of the above noted conditions not being met.

164

F-150 (TFC), enUSA, Third Printing

E146361Unique Driving Characteristics

Disabling Auto StartStop

Press the Auto StartStop button located on the center console to switch the system off. The button will illuminate. This will only deactivate the system for the current ignition cycle. Press the button again to restore Auto StartStop function. Note: If the Shift to P, Restart Engine message appears and the amber Auto StartStop indicator light is flashing, automatic restart is not available. You must restart the vehicle manually. See Information Displays (page 103). If your vehicle is in an engine off Auto StartStop state and you change the transmission to reverse (R) while the brake pedal is not pressed, the message Auto StartStop Press Brake to Start Engine will appear. You must press the brake pedal within 10 seconds or a shift to park (P) and a manual restart will be required.

Automatic Engine Restart Any of the following conditions will result in an automatic restart of the engine: •

You have removed your foot from the brake pedal. You press the accelerator pedal. You press the accelerator and the brake pedal at the same time. The driver safety belt becomes unfastened or the driver door is ajar. You have moved the transmission from drive (D) to any gear except park (P). Your vehicle is moving. The interior compartment does not meet customer comfort when air conditioning or heat is on. Fogging of the windows could occur and the air conditioning is on. The battery is not within optimal operating conditions. You have exceeded the maximum engine off time.

• When you press the Auto StartStop

button with the engine automatically stopped. The front defroster is turned to the Max setting.

• •

•

•

• •

•

•

•

•

Any of the following conditions may result in an automatic restart of the engine: You have increased the blower fan • speed or changed the climate control temperature. You have an electrical accessory turned on or plugged in.

Note: You may notice that the climate seat fan fluctuates during an automatic restart.

•

165

F-150 (TFC), enUSA, Third Printing

E181352Fuel and Refueling

SAFETY PRECAUTIONS

WARNINGS

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray

and fire.

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

Automotive fuels can cause serious injury or death if you misuse or mishandle them. Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if you pump fuel into an ungrounded fuel container.

Observe the following guidelines when handling automotive fuel:

F-150 (TFC), enUSA, Third Printing

•

Extinguish all smoking materials and any open flames before refueling your vehicle.

• Automotive fuels can be harmful or

fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

• Avoid getting fuel liquid in your eyes. If

you splash fuel in your eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin. If you splash fuel on your skin, clothing or both, promptly remove contaminated clothing and wash your skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If you splash fuel on your skin, promptly wash your skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

•

•

166

Fuel and Refueling

FUEL QUALITY Choosing the Right Fuel Without a Flex Fuel Vehicle (If Equipped) Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 15% ethanol in your gasoline vehicle. If your vehicle is a Flex Fuel Vehicle (FFV), the fuel fill inlet will have a yellow housing. Do not use: •

Fuel containing more than 15% ethanol or E-85 fuel. Fuel with methanol. Fuels containing metallic based additives, including manganese-based compounds. Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT) Leaded fuel (The use of leaded fuel is prohibited by law).

• •

•

•

Note: Use of any fuel other than recommended fuel can cause powertrain damage, impair the emission control system or cause loss of vehicle performance. Any damage to vehicle that is caused by use of fuel not recommended will not be covered under warranty. Choosing the Right Fuel With a Flex Fuel Vehicle (If Equipped) Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 85% ethanol (E-85) in your Flex Fuel Vehicle (FFV). If your vehicle is a Flex Fuel Vehicle (FFV), the fuel fill inlet will have a yellow housing. Do not use: •

Fuels containing more than 85% ethanol or E-100 fuel. Fuel with methanol.

•

F-150 (TFC), enUSA, Third Printing

•

•

•

Fuels containing metallic based additives, including manganese-based compounds. Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT) Leaded fuel (The use of leaded fuel is prohibited by law).

Note: Use of any fuel other than recommended fuel can cause powertrain damage, impair the emission control system or cause loss of vehicle performance. Any damage to vehicle that is caused by use of fuel not recommended will not be covered under warranty. Octane Recommendations

Do not be concerned if the engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, contact an authorized dealer to prevent any engine damage. 2.7L and 3.5L EcoBoost Engines We recommend regular unleaded gasoline with a pump (R+M)/2 octane rating of 87. Some stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. We do not recommend fuels with an octane rating below 87. To provide improved performance, we recommend premium fuel for severe duty usage, such as trailer tow.

167

E161513Fuel and Refueling

3.5L V6 and 5.0L V8 Engines We recommend regular unleaded gasoline with a pump (R+M)/2 octane rating of 87. Some stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. We do not recommend fuels with an octane rating below 87. RUNNING OUT OF FUEL Avoid running out of fuel. This may have an adverse effect on powertrain components. If your vehicle runs out of fuel: •

You may need to cycle the ignition from Off to On several times after refueling to allow the fuel system to pump the fuel from the fuel tank to the engine. On restarting, cranking time will take a few seconds longer than normal.

WARNINGS

Do not try to pry open or push open the capless fuel system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others.

When refueling the vehicle fuel tank from a fuel container, use the plastic funnel included with your vehicle. •

In SuperCab and SuperCrew vehicles, the funnel is located under the second row passenger side seat near the spare tire toolbox.

• On regular cab vehicles, the funnel is

located behind the passenger seat.

When refueling the vehicle fuel tank from a fuel container, do the following: 1. Locate the plastic funnel.

• Normally, adding 1 gal (3.8 L) of fuel is

enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gal (3.8 L) may be required. The service engine soon indicator may come on. For more information on the service engine soon indicator, See Audible Warnings and Indicators (page 102).

•

For information on calculating DTE (Distance to empty), See Instrument Cluster (page 95). Refilling With a Portable Fuel Container

WARNINGS

Do not insert the nozzle of a fuel container or an aftermarket funnel into the fuel filler neck. This may

damage the fuel system filler neck or its seal and cause fuel to run onto the ground.

2.

Insert the plastic funnel into the fuel tank filler pipe opening.

3. Fill the vehicle with fuel from the

portable fuel container.

4. Clean the plastic funnel and place it

back in your vehicle or properly dispose of it.

Note: Extra funnels can be purchased from an authorized dealer if you choose to dispose of the funnel.

168

F-150 (TFC), enUSA, Third Printing

E142668Fuel and Refueling

•

Keep the fuel pump nozzle in contact with the fuel container while filling. • Do not use a device that would hold

the fuel pump handle in the fill position. Easy Fuel™ Capless Fuel System

WARNING

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

When fueling your vehicle: 1. When your vehicle has stopped, shift into park (P) and switch the ignition off.

2. Fully open the fuel tank filler door until

it engages.

3.

Insert the fuel pump nozzle up to the first notch on the nozzle. Hold handle higher during insertion for easier access. Leave the fuel pump nozzle fully inserted until you are done pumping.

REFUELING

WARNINGS

Fuel vapor burns violently and a fuel fire can cause severe injuries. Read and follow all the instructions on the pump island. When refueling always shut the engine off and never allow sparks or open flames near the fuel tank filler

valve. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is

against the law in some places.

Keep children away from the fuel pump; never let children pump fuel. Wait at least 10 seconds before removing the fuel pump nozzle to allow any residual fuel to drain into

the fuel tank.

Stop refueling after the fuel pump nozzle automatically shuts off for the second time. Failure to follow this

will fill the expansion space in the fuel tank and could lead to fuel overflowing.

Do not remove the fuel pump nozzle from its fully inserted position when refueling.

Use the following guidelines to avoid electrostatic charge build-up, which can produce a spark, when filling an ungrounded fuel container: • Place approved fuel container on the

ground.

• Do not fill a fuel container while it is in the vehicle (including the cargo area).

169

F-150 (TFC), enUSA, Third Printing

E156032Fuel and Refueling

If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after 4 or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. FUEL CONSUMPTION Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. The usable capacity of the fuel tank is • the amount of fuel that can be added into the tank after the gauge indicates empty The advertised capacity is the total fuel tank size. See Capacities and Specifications (page 358). It is the combined usable capacity plus the empty reserve.

•

• Due to the empty reserve, you may not be able to refuel the full amount of the advertised capacity of the fuel tank even when the fuel gauge reads empty.

Filling the Tank For consistent results when filling the fuel tank: •

Turn the ignition off before fueling; an inaccurate reading results if the engine is left running.

• Use the same fill rate

(low-medium-high) each time the tank is filled.

• Allow no more than two automatic

click-offs when filling.

4. Remove the fuel filler nozzle and fully

close the fuel tank filler door.

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank. The fill pipe is equipped with a drain hole. Excess fuel due to overfill may drain through the drain hole and drip onto the ground. If the fuel fill inlet was not properly closed, a service engine warning lamp may appear on the instrument cluster. At the next opportunity, do the following: 1. Stop your vehicle as soon as safely

possible and shift the transmission into park (P).

2. Switch the ignition off. 3. Open the fuel filler door and remove

any visible debris from the fuel fill opening. Insert either the fuel fill nozzle or the fuel fill funnel provided with the vehicle several times to allow the inlet to close properly. This will dislodge any debris preventing the inlet from sealing.

4.

170

F-150 (TFC), enUSA, Third Printing

E154765Fuel and Refueling

Conditions • Heavily loading a vehicle or towing a

trailer may reduce fuel economy at any speed.

• Carrying unnecessary weight may

reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400
pounds [180 kilograms] of weight carried).

• Adding certain accessories to your

vehicle (for example bug deflectors, rollbars/light bars, running boards, ski racks) may reduce fuel economy.

• Using fuel blended with alcohol may

lower fuel economy. Fuel economy may decrease with lower temperatures during the first 8–10
miles (12–16 kilometers) of driving.

•

• Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal.

•

• Close windows for high speed driving. EMISSION CONTROL SYSTEM

WARNINGS

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the

engine compartment and exhaust system, which can start a fire.

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If

you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.

Results are most accurate when the filling