2015 Ford F 150 Owners Manual

To reduce the risk of serious injury, when mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.38 bar) greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again.

WARNINGS

3. Stand at a minimum of 12 ft (3.6 m) away from the wheel and tire assembly. 4. Use both eye and ear protection. For a mounting pressure more than 20 psi (1.38 bar) greater than the maximum pressure, a Ford dealer or other tire service professional should do the mounting. Always inflate steel carcass tires with a remote air fill with the person inflating standing at a minimum of 12 ft (3.6 m) away from the wheel and tire assembly.

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. The two front tires or two rear tires should generally be replaced as a pair. The tire pressure sensors mounted in the wheels are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system.

340

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

If the tire pressure monitoring system indicator is flashing, the system is malfunctioning. Your replacement tire might be incompatible with your tire pressure monitoring system, or some component of the system may be damaged. Safety Practices

WARNINGS

If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.

Do not spin the wheels at over 35 mph (56 km/h). The

tires may fail and injure a passenger or bystander.

Driving habits have a great deal to do with your tire mileage and safety. *Observe posted speed limits *Avoid fast starts, stops and turns *Avoid potholes and objects on the road *Do not run over curbs or hit the tire against a curb when parking

Highway Hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under-inflated or damaged, deflate it, remove wheel and replace it with your spare tire and wheel. If you cannot detect a cause, have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected. Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically.

341

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare wheel and tire assembly it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements. Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. Rear-wheel drive vehicles and four-wheel drive vehicles (front tires at left of diagram)

Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front-wheel drive vehicles and those with an independent rear suspension may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire Rotation

WARNING

If the tire label shows different tire pressures for the front and rear tires and the vehicle is equipped with a tire pressure monitoring system, then the settings for the system sensors need to be updated. Always perform the system reset procedure after tire rotation. If the system is not reset, it may not provide a low tire pressure warning when necessary. See the tire pressure monitoring system reset procedure in this chapter. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.

342

F-150 (TFC), enUSA, Third Printing

E142548Wheels and Tires

• Only certain snow cables or chains

have been approved by Ford/Lincoln as safe for use on your vehicle with the following tires: 245/70R17, LT245/70R17, 265/70R17 and 265/60R18. You should install snow cables or chains that have been rated as SAE Class S. Install chains securely, verifying that the chains do not touch any wiring, brake lines, or fuel lines.

•

•

• Do not exceed 30 mph (50 km/h) or

less if recommended by the chain manufacturer while using snow chains. • Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and retighten the chains. If this does not work, remove the chains to prevent damage to your vehicle.

• Remove the tire chains when they are

no longer needed. Do not use tire chains on dry roads.

• Purchase chains or cables from a

manufacturer that clearly labels body to tire dimension restrictions. The snow chains or cables must be mounted in pairs on the rear tires only.

If you have any questions regarding snow chains or cables, please contact your Ford/Lincoln authorized dealer.

Sometimes irregular tire wear can be corrected by rotating the tires. USING SNOW CHAINS

WARNING

Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally, the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure.

Note: The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. The tires on your vehicle have all-weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and cables. If you need to use cables, it is recommended that steel wheels (of the same size and specifications) be used, as cables may chip aluminum wheels. Follow these guidelines when using snow tires and chains: •

If possible, avoid fully loading your vehicle.

• Use only cable type chains or chains

offered by Ford/Lincoln as an accessory or equivalent. Other conventional link type chains may contact and cause damage to the vehicle's wheel house and/or body.

• Do not install chains on the front tires as this may interfere with suspension components.

343

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

TIRE PRESSURE MONITORING SYSTEM

WARNING

The tire pressure monitoring system is not a substitute for manually checking the tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire pressure gauge. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

344

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low. Once the light is illuminated, your tires are under-inflated and need to be inflated to the manufacturer’s recommended tire pressure. Even if the light turns on and a short time later turns off, your tire pressure still needs to be checked. When Your Temporary Spare Tire is Installed When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle. To restore the full function of the tire pressure monitoring system, have the damaged road wheel and tire assembly repaired and remounted on your vehicle. When You Believe Your System is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. See the following chart for information concerning your tire pressure monitoring system:

This device complies with part 15 of the FCC Rules and with Licence exempt RSS Standards of Industry Canada. Operation is subject to the following two conditions: •

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.

•

Changing Tires With a Tire Pressure Monitoring System

Note: Each road tire is equipped with a tire pressure sensor located inside the wheel and tire assembly cavity. The pressure sensor is attached to the valve stem. The pressure sensor is covered by the tire and is not visible unless the tire is removed. Take care when changing the tire to avoid damaging the sensor. You should always have your tires serviced by an authorized dealer. Check the tire pressure periodically (at least monthly) using an accurate tire gauge. See Inflating Your Tires in this chapter.

345

F-150 (TFC), enUSA, Third Printing

E142549Wheels and Tires

Low tire pressure

warning light

Possible cause

Customer action required

Solid warning light

Tire(s) under-inflated

Spare tire in use

Tire pressure monitoring

system malfunction

Tire rotation without

sensor training

Flashing warning

light

Spare tire in use

Tire pressure monitoring

system malfunction

Make sure tires are at the proper pres- sure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off. Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible. On vehicles with different front and rear tire pressures, the system must be retrained following every tire rotation. See Tire Care (page 328). Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible.

346

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

When Inflating Your Tires When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires. It may take up to two minutes of driving over 20 mph (32 km/h) for the light to turn off after you have filled your tires to the recommended inflation pressure. How Temperature Affects Your Tire Pressure The tire pressure monitoring system monitors tire pressure in each pneumatic tire. While driving in a normal manner, a typical passenger tire inflation pressure may increase about 2 to 4 psi (14 to 28
kPa) from a cold start situation. If the vehicle is stationary overnight with the outside temperature significantly lower than the daytime temperature, the tire pressure may decrease about 3 psi (21
kPa) for a drop of 30°F (17°C) in ambient temperature. This lower pressure value may be detected by the tire pressure monitoring system as being significantly lower than the recommended inflation pressure and activate the system warning light for low tire pressure. If the low tire pressure warning light is on, visually check each tire to verify that no tire is flat. If one or more tires are flat, repair as necessary. Check the air pressure in the road tires. If any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure.

Tire Pressure Monitoring System Reset Procedure

WARNING

To determine the required pressure(s) for your vehicle, see the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label located on the B-Pillar or the edge of the driver's door.

Note: You need to perform the tire pressure monitoring system reset procedure after each tire rotation on vehicles that require different recommended tire pressures in the front tires as compared to the rear tires. Overview To provide the vehicle's load carrying capability, some vehicles require different recommended tire pressures in the front tires as compared to the rear tires. The tire pressure monitoring system equipped on these vehicles is designed to illuminate the low tire pressure warning light at two different pressures; one for the front tires and one for the rear tires. Since tires need to be rotated to provide consistent performance and maximum tire life, the tire pressure monitoring system needs to know when the tires are rotated to determine which set of tires are on the front and which are on the rear. With this information, the system can detect and properly warn of low tire pressures. System reset tips:

347

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

•

To reduce the chances of interference from another vehicle, perform the system reset procedure at least three feet (one meter) away from another Ford Motor Company vehicle undergoing the system reset procedure at the same time.

• Do not wait more than two minutes between resetting each tire sensor or the system will time-out and the entire procedure will have to be repeated on all four wheels.

• A double horn will sound indicating the

need to repeat the procedure.

Performing the System Reset Procedure Read the entire procedure before attempting. 1. Drive the vehicle above 20 mph (32
km/h) for at least two minutes, then park in a safe location where you can easily get to all four tires and have access to an air pump.

2. Place the ignition in the off position and

keep the key in the ignition.

3. Cycle the ignition to the on position

with the engine off.

4. Turn the hazard flashers on then off

three times. You must accomplish this within 10 seconds. If the reset mode has been entered successfully, the horn will sound once, the system indicator will flash and a message is shown in the information display. If this does not occur, please try again starting at Step 2. If after repeated attempts to enter the reset mode, the horn does not sound, the system indicator does not flash and no message is shown in the information display, seek service from your authorized dealer.

5. Train the tire pressure monitoring

system sensors in the tires using the following system reset sequence starting with the left front tire in the following clockwise order: Left front (driver's side front tire), Right front (passenger's side front tire), Right rear (passenger's side rear tire), Left rear (driver's side rear tire).

6. Remove the valve cap from the valve stem on the left front tire. Decrease the air pressure until the horn sounds. Note: The single horn chirp confirms that the sensor identification code has been learned by the module for this position. If a double horn is heard, the reset procedure was unsuccessful, and you must repeat it.

7. Remove the valve cap from the valve stem on the right front tire. Decrease the air pressure until the horn sounds. 8. Remove the valve cap from the valve stem on the right rear tire. Decrease the air pressure until the horn sounds.

9. Remove the valve cap from the valve stem on the left rear tire. Decrease the air pressure until the horn sounds. Training is complete after the horn sounds for the last tire trained (driver's side rear tire), the system indicator stops flashing, and a message is shown in the information display.

10. Turn the ignition off. If two short horn beeps are heard, the reset procedure was unsuccessful and you must repeat it. If after repeating the procedure and two short beeps are heard when the ignition is turned to off, seek assistance from your authorized dealer.

348

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

11.

Set all four tires to the recommended air pressure as indicated on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position) or Tire Label located on the B-Pillar or the edge of the driver's door. CHANGING A ROAD WHEEL

WARNINGS

The use of tire sealant may damage your tire pressure monitoring system and should only be used in roadside emergencies. If you must use a sealant, the Ford Tire Mobility Kit sealant should be used. The tire pressure monitoring system sensor and valve stem on the wheel must be replaced by an authorized dealer after use of the sealant.

If the tire pressure monitor sensor becomes damaged, it will no longer function. See Tire Pressure Monitoring System (page 344).

Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on this vehicle. If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road.

Have a flat serviced by an authorized dealer in order to prevent damage to the system sensors See Tire Pressure Monitoring System (page 344). Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the system sensor for damage. Dissimilar Spare Wheel and Tire Assembly Information WARNING

Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

If you have a dissimilar spare wheel and tire, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road wheel and tire assembly that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY

349

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

When driving with one of the dissimilar spare tires listed above, do not: Exceed 50 mph (80 km/h). • • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label. Tow a trailer.

• • Use snow chains on the end of the

vehicle with the dissimilar spare tire.

• Use more than one dissimilar spare tire

at a time.

• Use commercial car washing

equipment. Try to repair the dissimilar spare tire.

• Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking

performance.

• Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability. 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare wheel and tire assembly, do not: • • Use more than one dissimilar spare wheel and tire assembly at a time.

Exceed 70 mph (113 km/h).

Body style Regular Cab

Super Cab and Crew Cab

• Use commercial car washing

equipment.

• Use snow chains on the end of the

vehicle with the dissimilar spare wheel and tire assembly.

The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking

performance.

• Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability. When driving with the full-size dissimilar spare wheel and tire assembly additional caution should be given to: • • Driving vehicles equipped with a

Towing a trailer.

camper body.

• Driving vehicles with a load on the

cargo rack.

Drive cautiously when using a full-size dissimilar spare wheel and tire assembly and seek service as soon as possible. Location of the Spare Tire and Tools The spare tire is located under the vehicle, just forward of the rear bumper. The jack, jack handle and lug wrench are located in the following locations:

Location

Attached to the floor behind the passenger seat (for easier access, move the passenger

seat forward)

Attached behind the rear seat on the

passenger side

350

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

WARNINGS

Disable the power running boards before jacking, lifting, or placing any object under the vehicle. Never place

your hand between the power running board and the vehicle as extended power running boards will retract when the doors are closed. Failure to follow these instructions may result in personal injury. Failure to follow these instructions when using the spare tire carrier could cause loss of the wheel and tire and lead to personal injury: Only use the spare tire carrier to stow the tire and wheel combination specified on the Tire Label or Safety Compliance Certification Label on the B-Pillar or the edge of the driver door. Other tire and wheel combinations could cause the carrier to fail if it does not fit securely or is too heavy. Do not use impact tools or power tools operating over 200 RPM, which may cause winch malfunction and prevent a secure fit. Override the winch at least three times (there will be an audible click each time) to ensure a tight secure fit of the wheel and tire.

Note: Passengers should not remain in the vehicle when the vehicle is being jacked. Park on a level surface, activate the hazard flashers and set the parking brake. Then, place the transmission in park (P) and turn the engine off.

Tire Change Procedure WARNINGS

When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from

moving or slipping off the jack.

To help prevent the vehicle from moving when you change a tire, be sure to place the transmission in park

(P), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.

Never get underneath a vehicle that is supported only by a jack. If the vehicle slips off the jack, you or

someone else could be seriously injured. Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.

Always use the jack provided as original equipment with your vehicle. If using a jack other than the one

provided as original equipment with your vehicle, make sure the jack capacity is adequate for the vehicle weight, including any vehicle cargo or modifications.

351

F-150 (TFC), enUSA, Third Printing

Wheels and Tires

Removing the Jack and Tools

Removing the Spare Tire

1. From the passenger side of the vehicle, unstrap the large center strap securing the jacking kit to the floor posts.

2. Remove the fuel funnel. 3. With slight downward pressure, slide

the jacking kit outward, toward the passenger side of the vehicle.

4. Lift the jacking kit off the floor posts.

352

F-150 (TFC), enUSA, Third Printing

E206264E188735Wheels and Tires

1. Use your key to remove the lock

cylinder from the access hole of the bumper to allow access to the guide tube. Assemble the jack handle as shown in the illustration.

6. Obtain the spare tire and jack from

their storage locations.

7. Loosen each wheel lug nut on the

affected flat tire one-half turn counterclockwise, but do not remove them.

Jacking the Vehicle Front Jacking Points

2. Fully insert the jack handle through the

bumper hole and into the guide tube through the access hole in the rear bumper.

3. Turn the handle counterclockwise until

the tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack.

4. Remove the retainer from the center

of the wheel.

5. Block both the front and rear of the

wheel diagonally opposite the flat tire. For example, if the left front tire is flat, block the right rear wheel.

353

F-150 (TFC), enUSA, Third Printing

Note: Use the frame rail as the jacking location point, not the control arm. The frame rail is marked with an arrow.

E184020E175447E183709Rear Jacking Points

Wheels and Tires

5. Remove the jack and fully tighten the lug nuts in the order shown. See Technical Specifications (page 357). 6. Stow the flat tire. See the Stowing the

Flat or Spare Tire.

7. Stow the jack and lug wrench. Make

sure the jack is fastened securely before you drive. See Stowing the Jack and Tools.

8. Unblock the wheels.

Note: Jack at the specified locations to avoid damage to the vehicle. 1. Place the jack at the jacking point next

to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground.

2. Remove the lug nuts with the lug

wrench.

3. Replace the flat tire with the spare tire,

making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.

4. Lower the wheel by turning the jack

handle counterclockwise.

Stowing the Flat or Spare Tire Note: Failure to follow the spare tire stowage instructions may result in failure of the cable or loss of the spare tire. 1. Lay the tire on the ground with the

valve stem facing up.

2. Slide the wheel partially under the

vehicle and install the retainer through the wheel center. Pull on the cable to align the components at the end of the cable.

3. Turn the jack handle clockwise until

the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness. Tighten to

354

F-150 (TFC), enUSA, Third Printing

E183403E166719135462Wheels and Tires

the best of your ability, to the point where the ratchet or slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, contact your authorized dealer. 4. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary. Failure to properly stow the spare tire may result in failure of the winch cable and loss of the tire.

5. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, as per your scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. If removed, install the spare tire lock into the bumper drive tube with the spare tire lock key and jack handle.

6.

Stowing the Jack and Tools 1. Place the jacking tools in the tool bag

and secure the velcro flaps.

2. Adjust the jack up or down by rotating the lead screw located on the end of the jack. The stowage markings should line up with the bottom channel.

3. Place the jack in the vehicle so that the

lead screw adjustment is facing the driver side of the vehicle.

4. Place the tool bag on top of the jack. The jack base fits within the opening of the jack tool bag.

5. Attach the flap around the lead screw

and secure the flap to the velcro.

6. Secure the two D-ring straps tightly. 7. Secure the velcro straps through the

hole of the lead screw tightly.

8. Place the jack so the lug wrench faces the rear of the vehicle. Position the jack base so the key hole slots align with the jacking posts.

355

F-150 (TFC), enUSA, Third Printing

E184021Wheels and Tires

9. With slight downward pressure, slide the jack and tool assembly toward the driver side of the vehicle until it stops.

10. Secure the large strap. 11.

Clip the fuel funnel back in place.

356

F-150 (TFC), enUSA, Third Printing

E184022Wheels and Tires

TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications

WARNING

When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while your vehicle is in motion, resulting in loss of control.

Bolt size M14 x 1.5

lb.ft (Nm)

150 lb.ft (204 Nm)

*Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. Retighten the lug nuts to the specified torque within 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal).

Wheel pilot bore

Inspect the wheel pilot hole and mounting surface prior to installation. Remove any visible corrosion or loose particles.

357

F-150 (TFC), enUSA, Third Printing

E145950Capacities and Specifications

ENGINE SPECIFICATIONS

Engine

2.7L EcoBoost

3.5L V6 Ecoboost

3.5L V6 TiVCT

164

Minimum 87

octane

1-4-2-5-3-6
Coil on plug

214

Minimum 87

octane

1-4-2-5-3-6
Coil on plug

214

Minimum 87
octane or E85
1-4-2-5-3-6
Coil on plug

5.0L V8

302

Minimum 87
octane or E85
1-5-4-8-6-3-7-2

Coil on plug

.028-.031 (0.7 -

0.8 mm)

.030-.033 in.

(0.75 - 0.85 mm)

.049-.053 in.

(1.25 - 1.35 mm)

.049-.053 in.

(1.25 - 1.35 mm)

10.0:1

10.0:1

10.8:1

10.5:1

Cubic inches

Required

fuel

Firing order

Ignition system

Spark plug

gap

Compres- sion ratio

Drivebelt Routing 2.7L Ecoboost Engines with A/C

3.5L V6 Engines with A/C

5.0L V8 Engines with A/C

358

F-150 (TFC), enUSA, Third Printing

E176088E167467E167465Capacities and Specifications

MOTORCRAFT PARTS

Component

2.7L Ecoboost

3.5L V6
Ecoboost FA-1883

3.5L V6 TiVCT

5.0L V8

FA-1883

FA-1883

FA-1883

FL-2062

FL-500-S

FL-500-S

FL-500-S

BAGM-48H6-

760

BXT-48H6-610

BXT-48H6-610

BXT-48H6-610

BAGM-94RH7-

800

(King Ranch, Lariat and Premium) SP-542

BXT-94RH7-730

(King Ranch, Lariat and Premium)

SP-534

BXT-94RH7-

BXT-94RH7-

730

(King Ranch, Lariat and Premium) SP-520

730

(King Ranch, Lariat and Premium) SP-519

Air filter element Oil filter Battery

Spark plugs Windshield wiper blade Cabin air filter

WW-2242

FP-79

VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel.

We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance. These parts meet or exceed Ford Motor Company’s specifications and are engineered for your vehicle. Use of other parts may impact vehicle performance, emissions and durability. Your warranty may be void for any damage related to use of other parts. If a Motorcraft oil filter is not available, use an oil filter that meets industry performance specification SAE/USCAR-36. For spark plug replacement, contact an authorized dealer. Replace the spark plugs at the appropriate intervals. See Scheduled Maintenance (page 498).

359

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Model year Assembly plant Production sequence number

VEHICLE CERTIFICATION LABEL

The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label shall be affixed to either the door hinge pillar, the door latch post, or the edge of the door near the door latch, next to the driver's seating position.

Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number contains the following information:

World manufacturer identifier Brake system, Gross Vehicle Weight Rating, Restraint Devices and their locations Make, vehicle line, series, body type Engine type Check digit

360

F-150 (TFC), enUSA, Third Printing

E142476E142477E167469Capacities and Specifications

TRANSMISSION CODE DESIGNATION

The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description.

Description

Six-speed automatic transmission 6R80E

Code

361

F-150 (TFC), enUSA, Third Printing

E167814Capacities and Specifications

CAPACITIES AND SPECIFICATIONS - 2.7L ECOBOOST™ Capacities

WARNING

The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.

Item

Capacity

Between MIN/MAX on brake fluid reservoir

6.0 qt (5.7 L) 16.4 qt (15.5 L)

3.5 pt (1.7 L) 5.5 pt (2.6 L) 13.1 qt (12.4 L) 1.5 qt (1.4 L)

Engine oil Engine coolant Brake fluid Front axle fluid (Four-wheel drive) Rear axle fluid Automatic transmission fluid* Transfer case fluid Four-wheel drive (Electronic Shift-on-the- Fly) Transfer case fluid Automatic four-wheel drive (Torque on demand) Windshield washer fluid Fuel tank Fuel tank (Optional) A/C Refrigerant 3.4 fl oz (100.5 ml) A/C Refrigerant Compressor Oil *Approximate dry fill capacity. Actual amount may vary during fluid changes.

Fill as required 23 gal (87.1 L)

36.0 gal (136.2 L)

1.5 lb (0.68 kg)

1.5 qt (1.4 L)

362

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Specifications Materials

Name Recommended motor oil (U.S.): Motorcraft SAE 5W-30 Premium Synthetic Blend Motor Oil XO-5W30-QSP Recommended Motor oil (Canada): Motorcraft SAE 5W-30 Super Premium Motor Oil CXO-5W30-LSP12
Recommended motor oil (Mexico): Motorcraft SAE 5W-30 Synthetic Motor Oil MXO-5W30-QSP Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-30 Full Synthetic Motor Oil XO-5W30-QFS Optional Motor oil (Canada): Motorcraft SAE 5W-30 Synthetic Motor Oil CXO-5W30-LFS12
Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance Motor Vehicle Brake Fluid PM-20
Front axle fluid (U.S.): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL Front axle fluid (Canada): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant CXY-80W90-1L Front axle fluid (Mexico): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant MXY-80W90-QL

Specification

WSS-M2C946-A

WSS-M2C946-A

WSS-M2C946-A

WSS-M2C946-A

WSS-M2C946-A

WSS-M97B44-D2

WSS-M97B44-D2

WSS-M6C65-A2

WSP-M2C197-A

WSP-M2C197-A

WSP-M2C197-A

363

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Name

Rear axle fluid: Motorcraft SAE 75W-85 Premium Synthetic Hypoid Gear Lubricant XY-75W85-QL Automatic transmission fluid (U.S. and Mexico): Motorcraft MERCON LV Automatic Transmission Fluid XT-10-QLVC Automatic transmission fluid (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12
Transfer case fluid (Electronic Shift-On-the-Fly) (U.S. and Mexico): Motorcraft Transfer Case Fluid XL-12
Transfer case fluid (Electronic Shift-On-the-Fly) (Canada): Motorcraft Transfer Case Fluid CXL-12
Transfer case fluid (Torque On Demand) (U.S. and Mexico): Motorcraft MERCON LV Automatic Transmission Fluid XT-10-QLVC Transfer case fluid (Torque On Demand) (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12
Windshield washer fluid (U.S. and Mexico): Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2
Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19
A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R

364

Specification

WSS-M2C942-A

WSS-M2C938-A MERCON LV

WSS-M2C938-A MERCON LV

ESP-M2C166-H

ESP-M2C166-H

WSS-M2C938-A MERCON LV

WSS-M2C938-A MERCON LV

WSS-M14P19-A

WSS-M14P19-A

WSH-M17B19-A

WSH-M17B19-A

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Name

A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19
A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D Transmission, parking brake linkage and pivots and brake pedal shift grease: Premium Long-Life Grease XG-1-E1
Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5
Lock cylinders (U.S.): Penetrating and Lock Lubricant XL-1
Lock cylinders (Canada): Penetrating Fluid CXC-51-A Lock cylinders (Mexico): Penetrating and Lock Lubricant MXL-1

Specification

WSH-M17B19-A

WSH-M1C231-B

ESA-M1C75-B

ESB-M1C93-B

--

--

--

If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. Longer engine cranking periods. Increased emission levels.

• • • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance.

Only use fluid that meets Ford specifications. Motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines are also acceptable. Do not use oil labeled with API SN service category unless the label also displays the API certification mark.

365

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty. Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure. Note: Automatic transmissions that require MERCON LV transmission fluid should only use MERCON LV transmission fluid. The use of any other fluid may cause transmission damage.

An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of the International Lubricants Specification Advisory Council (ILSAC).

CAPACITIES AND SPECIFICATIONS - 3.5L ECOBOOST™ Capacities

WARNING

The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.

Item

Engine oil Engine coolant Brake fluid Front axle fluid (Four-wheel drive) Rear axle fluid Automatic transmission fluid* Transfer case fluid Four-wheel drive (Electronic Shift-on-the- Fly)

Capacity

6.0 qt (5.7 L) 15.6 qt (14.75 L)

Between MIN/MAX on brake fluid reservoir

3.5 pt (1.7 L) 5.5 pt (2.6 L) 13.1 qt (12.4 L) 1.5 qt (1.4 L)

366

F-150 (TFC), enUSA, Third Printing

E142732Capacities and Specifications

Item

Capacity 1.5 qt (1.4 L)

Transfer case fluid Automatic four-wheel drive (Torque on demand) Windshield washer fluid Fuel tank Fuel tank (Optional) A/C Refrigerant A/C Refrigerant Compressor Oil 3.4 fl oz (100.5 ml) *Approximate dry fill capacity. Actual amount may vary during fluid changes.

Fill as required 23 gal (87.1 L)

36.0 gal (136.2 L)

1.5 lb (0.68 kg)

Specifications Materials

Name Recommended motor oil (U.S.): Motorcraft SAE 5W-30 Premium Synthetic Blend Motor Oil XO-5W30-QSP Recommended Motor oil (Canada): Motorcraft SAE 5W-30 Super Premium Motor Oil CXO-5W30-LSP12
Recommended motor oil (Mexico): Motorcraft SAE 5W-30 Synthetic Motor Oil MXO-5W30-QSP Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-30 Full Synthetic Motor Oil XO-5W30-QFS Optional Motor oil (Canada): Motorcraft SAE 5W-30 Synthetic Motor Oil CXO-5W30-LFS12
Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B Engine coolant (Canada):

Specification

WSS-M2C946-A

WSS-M2C946-A

WSS-M2C946-A

WSS-M2C946-A

WSS-M2C946-A

WSS-M97B44-D2

WSS-M97B44-D2

367

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Name

Specification

Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance Motor Vehicle Brake Fluid PM-20
Front axle fluid (U.S.): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL Front axle fluid (Canada): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant CXY-80W90-1L Front axle fluid (Mexico): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant MXY-80W90-QL Rear axle fluid: Motorcraft SAE 75W-85 Premium Synthetic Hypoid Gear Lubricant XY-75W85-QL Automatic transmission fluid (U.S. and Mexico): Motorcraft MERCON LV Automatic Transmission Fluid XT-10-QLVC Automatic transmission fluid (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12
Transfer case fluid (Electronic Shift-On-the-Fly) (U.S. and Mexico): Motorcraft Transfer Case Fluid XL-12
Transfer case fluid (Electronic Shift-On-the-Fly) (Canada): Motorcraft Transfer Case Fluid CXL-12
Transfer case fluid (Torque On Demand) (U.S. and Mexico): Motorcraft MERCON LV Automatic Transmission Fluid XT-10-QLVC Transfer case fluid (Torque On Demand) (Canada):

WSS-M6C65-A2

WSP-M2C197-A

WSP-M2C197-A

WSP-M2C197-A

WSS-M2C942-A

WSS-M2C938-A MERCON LV

WSS-M2C938-A MERCON LV

ESP-M2C166-H

ESP-M2C166-H

WSS-M2C938-A MERCON LV

WSS-M2C938-A

368

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Name

Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12
Windshield washer fluid (U.S. and Mexico): Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2
Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19
A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19
A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D Transmission, parking brake linkage and pivots and brake pedal shift grease: Premium Long-Life Grease XG-1-E1
Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5
Lock cylinders (U.S.): Penetrating and Lock Lubricant XL-1
Lock cylinders (Canada): Penetrating Fluid CXC-51-A Lock cylinders (Mexico): Penetrating and Lock Lubricant MXL-1

Specification

MERCON LV

WSS-M14P19-A

WSS-M14P19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M1C231-B

ESA-M1C75-B

ESB-M1C93-B

--

--

--

369

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. Longer engine cranking periods. Increased emission levels.

• • • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance. Only use fluid that meets Ford specifications. Motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines are also acceptable. Do not use oil labeled with API SN service category unless the label also displays the API certification mark.

An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of the International Lubricants Specification Advisory Council (ILSAC). Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty. Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure. Note: Automatic transmissions that require MERCON LV transmission fluid should only use MERCON LV transmission fluid. The use of any other fluid may cause transmission damage.

CAPACITIES AND SPECIFICATIONS - 3.5L Capacities

WARNING

The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.

370

F-150 (TFC), enUSA, Third Printing

E142732Capacities and Specifications

Between MIN/MAX on brake fluid reservoir

Item

Capacity 6.3 qt (6 L)

15.3 qt (14.5 L) 15.1 qt (14.25 L)

3.5 pt (1.7 L) 5.5 pt (2.6 L) 13.1 qt (12.4 L) 1.5 qt (1.4 L)

Engine oil Engine coolant (with engine oil cooler) Engine coolant (without engine oil cooler) Brake fluid Front axle fluid (Four-wheel drive) Rear axle fluid Automatic transmission fluid* Transfer case fluid Four-wheel drive (Electronic Shift-on-the- Fly) Transfer case fluid Automatic four-wheel drive (Torque on demand) Windshield washer fluid Fuel tank Fuel tank (Optional) A/C Refrigerant A/C Refrigerant Compressor Oil 3.4 fl oz (100.5 ml) *Approximate dry fill capacity. Actual amount may vary during fluid changes.

Fill as required 23 gal (87.1 L)

36.0 gal (136.2 L)

1.5 lb (0.68 kg)

1.5 qt (1.4 L)

371

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Specifications Materials

Name Recommended motor oil (U.S.): Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP Recommended Motor oil (Canada): Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12
Recommended motor oil (Mexico): Motorcraft SAE 5W-20 Synthetic Motor Oil MXO-5W20-QSP Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-20 Full Synthetic Motor Oil XO-5W20-QFS Optional Motor oil (Canada): Motorcraft SAE 5W-20 Synthetic Motor Oil CXO-5W20-LFS12
Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance Motor Vehicle Brake Fluid PM-20
Front axle fluid (U.S.): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL Front axle fluid (Canada): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant CXY-80W90-1L Front axle fluid (Mexico): Motorcraft SAE 80W-90 Premium Rear Axle Lubricant MXY-80W90-QL

Specification

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M97B44-D2

WSS-M97B44-D2

WSS-M6C65-A2

WSP-M2C197-A

WSP-M2C197-A

WSP-M2C197-A

372

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Name

Rear axle fluid: Motorcraft SAE 75W-85 Premium Synthetic Hypoid Gear Lubricant XY-75W85-QL Automatic transmission fluid (U.S. and Mexico): Motorcraft MERCON LV Automatic Transmission Fluid XT-10-QLVC Automatic transmission fluid (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12
Transfer case fluid (Electronic Shift-On-the-Fly) (U.S. and Mexico): Motorcraft Transfer Case Fluid XL-12
Transfer case fluid (Electronic Shift-On-the-Fly) (Canada): Motorcraft Transfer Case Fluid CXL-12
Transfer case fluid (Torque On Demand) (U.S. and Mexico): Motorcraft MERCON LV Automatic Transmission Fluid XT-10-QLVC Transfer case fluid (Torque On Demand) (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12
Windshield washer fluid (U.S. and Mexico): Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2
Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19
A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R

373

Specification

WSS-M2C942-A

WSS-M2C938-A MERCON LV

WSS-M2C938-A MERCON LV

ESP-M2C166-H

ESP-M2C166-H

WSS-M2C938-A MERCON LV

WSS-M2C938-A MERCON LV

WSS-M14P19-A

WSS-M14P19-A

WSH-M17B19-A

WSH-M17B19-A

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Name

A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19
A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D Transmission, parking brake linkage and pivots and brake pedal shift grease: Premium Long-Life Grease XG-1-E1
Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5
Lock cylinders (U.S. and Mexico): Penetrating and Lock Lubricant XL-1
Lock cylinders (Canada): Penetrating Fluid CXC-51-A Lock cylinders (Mexico): Penetrating and Lock Lubricant MXL-1

Specification

WSH-M17B19-A

WSH-M1C231-B

ESA-M1C75-B

ESB-M1C93-B

--

--

--

If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. Longer engine cranking periods. Increased emission levels.

• • • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance.

Only use fluid that meets Ford specifications. Motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines are also acceptable. Do not use oil labeled with API SN service category unless the label also displays the API certification mark.

374

F-150 (TFC), enUSA, Third Printing

Capacities and Specifications

Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty. Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure. Note: Automatic transmissions that require MERCON LV transmission fluid should only use MERCON LV transmission fluid. The use of any other fluid may cause transmission damage.

An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of the International Lubricants Specification Advisory Council (ILSAC).