2010 Ford Explorer Owners Manual

when leaving the vehicle.

WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the

LOCK position and remove the key whenever you leave your vehicle.

302

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Driving

WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be

working properly. See your authorized dealer.

AWD Systems (if equipped) AWD uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Note: The Tire Pressure Monitoring System (TPMS) indicator light may illuminate depending on how much air is released from your tires and/or how long you drive the vehicle under these conditions. Avoid excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even AWD and 4WD vehicles can lose traction in slick mud. As when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels. If the vehicle does slide, steer in the direction of the slide until you regain control of the vehicle.

303

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Driving

If the transmission, transfer case or front axle are submerged in water, their fluids should be checked and changed, if necessary. Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components. “Tread Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.” Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer. When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. If you do stall out, do not try to turn around because you might roll over. It is better to back down to a safe location. Apply just enough power to the wheels to climb the hill. Too much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control. 304

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Driving

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t turn and if they aren’t turning, you won’t be able to steer. The front wheels have to be turning in order to steer the vehicle. Rapid pumping of the brake pedal will help you slow the vehicle and still maintain steering control. If your vehicle has anti-lock brakes, apply the brakes steadily. Do not “pump” the brakes. Driving on snow and ice AWD and 4WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. Avoid sudden braking as well. Although an AWD or a 4WD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster, because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions. Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, avoid locking of the wheels. Use a “squeeze” technique, push on the brake pedal with a steadily increasing force which allows the wheels to brake yet continue to roll so that you may steer in the direction you want to travel. If you lock the wheels, release the brake pedal and repeat the squeeze technique. If your vehicle is equipped with a Four Wheel Anti-Lock Brake System (ABS), apply the brake steadily. Do not “pump” the brakes. Refer to the Brakes section of this chapter for additional information on the operation of the anti-lock brake system.

305

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Driving

WARNING: If you are driving in slippery conditions that require tire cables, then it is critical that you drive cautiously. Keep

speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death. If the rear end of the vehicle slides while cornering, steer in the direction of the slide until you regain control of the vehicle.

Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability. For this reason, Ford Motor Company strongly recommends that you do not make modifications such as adding or removing parts (such as lift kits or stabilizer bars) or by using replacement parts not equivalent to the original factory equipment. Any modifications to a vehicle that raise the center of gravity can make it more likely the vehicle will roll over as a result of a loss of control. Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover). Failure to maintain your vehicle properly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety. Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off-road usage.

306

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Driving

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).

When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the water, always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. Wet brakes do not stop the vehicle as quickly as dry brakes.

307

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

ROADSIDE ASSISTANCE

Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24-hours, seven days a week • for the coverage period listed on the Roadside Assistance Card

included in your Owner Guide portfolio.

responsibility)

supplied with a tire inflation kit)

Roadside assistance will cover: • a flat tire change with a good spare (except vehicles that have been • battery jump start • lock-out assistance (key replacement cost is the customer’s • fuel delivery – Independent Service Contractors, if not prohibited by state, local or municipal law shall deliver up to 2.0 gallons (7.5L) of gasoline or 5.0 gallons (18.9L) of diesel fuel to a disabled vehicle. Fuel delivery service is limited to two no-charge occurrences within a 12-month period. • winch out – available within 100 feet (30.5 meters) of a paved or • towing – Ford/Mercury/Lincoln eligible vehicle towed to an authorized dealer within 35 miles (56 km) of the disablement location or to the nearest authorized dealer. If a member requests to be towed to an authorized dealer more than 35 miles (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 miles (56 km).

county maintained road, no recoveries.

Trailers shall be covered up to $200 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services. Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts 308

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1-877-294-2582 or visit our website at www.ford.ca.

Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Customer Information Guide in the glove compartment. U.S. Ford, Mercury and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. Canadian customers who require roadside assistance, call 1-800-665-2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 km). To obtain reimbursement information, U.S. Ford, Mercury and Lincoln vehicle customers call 1-800-241-3673. Customers will be asked to submit their original receipts. Canadian customers who need to obtain reimbursement information, call 1-800-665-2006.

HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Press in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

309

Roadside Emergencies

Note: With extended use, the flasher may run down your battery. FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the off position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pressing in on the reset button. 4. Turn the ignition to the on position. Pause for a few seconds and return the key to the off position. 5. Make a further check for leaks in the fuel system.

FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. 310

15

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Standard fuse amperage rating and color

Roadside Emergencies

Fuse rating

Mini fuses

2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A

Grey Violet Pink Tan

Brown

Red Blue Yellow Natural Green

— — — — —

COLOR Standard

fuses Grey Violet Pink Tan

Brown

Red Blue Yellow Natural Green

— — — — —

Passenger compartment fuse panel The fuse panel is located below the instrument panel on the driver’s side.

Maxi fuses

Cartridge maxi fuses

— — — — — — —

Yellow

—

Green Orange

Red Blue Tan

Natural

— — — — — — — Blue — Pink Green Red Yellow

— —

To remove a fuse use the fuse puller tool provided on the fuse panel box.

311

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

12

11

10

CB1

16

15

14

13

20

19

18

17

24

23

22

21

28

27

26

25

The fuses are coded as follows:

Fuse/Relay Location

Fuse Amp

Rating

10

11

312

20A

5A 20A

10A

5A

20A

15A 15A

2A

5A

5A

Protected Circuits

Moon roof, Adjustable pedals, Memory seats, Lumbar motor Microcontroller power Radio, Navigation amplifier, GPS module On-board diagnostic (OBD II) connector Moon roof, Door lock switch illumination, Auto dimming rear view mirror Liftglass release motor, Door unlock/lock Trailer stop/turn Ignition switch power, Passive anti-theft system (PATS), Cluster 6R Transmission control module/Powertrain control module (Ignition RUN/START), Fuel pump relay Front wiper RUN/ACC relay in power distribution box (PDB) Radio start

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Fuse/Relay Location

12

13

14
15
16
17

18

19
20

21
22

23

24
25
26

27
28
CB1

Fuse Amp

Rating

5A

15A

20A 10A 10A 10A

10A

— 10A

— 15A

15A

10A 15A 15A

15A 10A 25A

Roadside Emergencies

Protected Circuits

Rear wiper motor RUN/ACC, Trailer battery charge relay in PDB, Radio Heated mirror, Manual climate rear defrost indicator Horn Reverse lamps Trailer reverse lamps Restraints control module, Passenger occupancy Reverse park aid, Roll Stability Control™ (RSC威) switch, RSC威, 4x4 module, 4x4 switch, Heated seat switches, Auxiliary climate control Not used Climate control system, Brake shift Not used Brake switch, Bi-color stop lamps, High-mount brake lamp, All turn lamps Interior lamps, Puddle lamps, Battery saver, Instrument illumination, HomeLink威 Cluster, Theft indicator light Trailer tow park lamps License plate/rear park lamp, Front park lamps, Manual climate Tri-color stop lamps Climate controls Windows

313

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

The following relays are located on either side of the passenger compartment fuse panel. See your authorized dealer for service of these relays.

Fuse/Relay Location

Relay 1

Description

Delayed accessory relay

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.

WARNING: Always disconnect the battery before servicing high current fuses.

WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the

battery or refilling fluid reservoirs.

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.

314

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

The high-current fuses are coded as follows:

Roadside Emergencies

Fuse/Relay Location

10
11
12
13
14

15
16
17
18
19
20
21
22
23
24

Fuse Amp

Rating 50A**

50A**

50A**

30A** 30A** 40A**

40A**

— —

30A** 30A** 30A** 30A** 30A** 40A** 40A** 40A** 30A** 30A** 30A** 30A** 20A* 20A* 20A* 10A*

Protected Circuits

Battery feed 2 (passenger compartment fuse panel) Battery feed 3 (passenger compartment fuse panel) Battery feed 1 (passenger compartment fuse panel) Fuel pump, Injectors Third row seat (left) Anti-lock brake system (ABS) pump Powertrain control module (PCM) Not used Not used Power seat (right) Starter Third row seat (right) Trailer tow battery charger Memory seats Non-memory seats Rear defrost, Heated mirrors Front blower motor Trailer electronic brakes Auxiliary blower motor Running boards Front wiper motor Rear power point Subwoofer 4x4
PCM – keep alive power, Canister vent

315

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

Fuse Amp

Protected Circuits

Rating 20A* 20A* 20A*

20A* 15A* 25A* 15A* 5A* 30A* 15A* 10A* 20A* 30A* 15A*

15A* 15A*

15A*

15A*

Front power point/Cigar lighter 4x4 module (4.6L engine only) 6R Transmission module (4.6L engine only) Heated seats Headlamps (right) Rear wiper Fog lamps Power mirrors ABS valve Headlamps (left) A/C clutch Console bin power point Driver window motor 5R Transmission (4.0L engine only) PCM power Fan clutch, Positive crackcase ventilation (PCV) valve, A/C clutch relay Satellite radio module, DVD, SYNC威 Redundant brake switch, Electronic vapor management valve, Mass air flow sensor, Heated exhaust gas oxygen (HEGO) sensor, EVR, Variable cam timing (VCT)1 (4.6L engine only), VCT2 (4.6L engine only), CMCV (4.6L engine only), Catalyst monitor sensor

Fuse/Relay Location

25
26
27

28
29
30
31
32
33
34
35
36
37
38

39
40

41

42

316

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

Protected Circuits

Coil on plug (4.6L engine only), Coil tower (4.0L engine only) Injectors Not used Not used Not used Not used Fuel pump relay A/C clutch relay Fog lamps relay Not used Not used One touch integrated start (OTIS) (diode) Trailer battery charger relay Front wiper relay PCM relay Starter relay Blower relay

Fuse Amp

Rating 15A*

15A*

— — — — — — — — — —

— — — — —

Fuse/Relay Location

43

44
45B 45A 46B 46A 49
50B 50A 51
52
53

54
55B 55A 56B 56A

* Mini Fuses ** Cartridge Fuses CHANGING THE TIRES If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensor, refer to Changing tires with TPMS in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible.

317

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System and should not be used.

WARNING: Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important

information. If the tire pressure monitor sensor becomes damaged, it will no longer function.

Dissimilar spare tire/wheel information

WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

Note: Turn off the power running boards (if equipped) before driving with a dissimilar spare tire/wheel. Refer to Running boards in the Driver Controls chapter. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare

Safety Compliance Label

tire

318

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

• Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare

tire/wheel

The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.

319

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

Stopping and securing the vehicle 1. Park on a level surface, activate the hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) and turn engine off.

3. Turn off the power running boards (if equipped). Refer to Running boards in the Driver Controls chapter. Note: Passengers should not remain in the vehicle when the vehicle is being jacked. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations:

Tool

Spare tire

Jack, lug nut wrench, jack handle,

wheel chock

Location

Under the vehicle, just in front of the rear bumper. The spare tire winch drive nut is located at the rear center of the cargo area under a lid. Behind the rear seat under the carpeted floor lid in the cargo floor. The tools are located in a bag attached to the jack.

320

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

Removing the jack and tools 1. Open liftgate and remove the carpeted floor lid. 2. Turn jack screw eyelet (1) counterclockwise to release pressure. 3. Rotate the locking pin (2) clockwise until loose then pull out until it stops and remove the jack and tool bag from the bracket.

4. Remove the chock and jack tools from the provided bag rotate the wrench socket out from the handle.

Removing the spare tire Do not use an impact wrench on the winch drive nut. This will damage the spare tire winch. 1. Open the cover from the carpeting on cargo floor to expose the winch drive nut.

321

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

2. Insert the lug wrench on the winch drive nut. The wrench will stop moving and forward resistance to turning will be felt when properly engaged.

3. Turn the wrench counterclockwise until the tire is lowered to the ground and the cable has slack. When turning the wrench, make sure that it does not scuff the kick plate. 4. Slide the tire rearward, lift one side and remove the retainer from the spare tire.

Changing the spare tire

WARNING: When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or

slipping off the jack, even if the transmission is in P (Park).

WARNING: To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the

wheel that is diagonally opposite (other end of the vehicle) to the tire being changed.

322

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

WARNING: If the vehicle slips off the jack, you or someone else could be seriously injured.

WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to

avoid the danger of being hit when operating the jack or changing the wheel.

WARNING: Turn off the running boards (if equipped) before working under the vehicle, jacking, or placing any object under the vehicle. Never place your hand in the hinge assemblies. A moving running board may cause injury.

Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block the wheel that is diagonally opposite of the flat tire using the wheel chock provided with your vehicle.

2. Use the tip of the lug wrench to remove the beauty cap by twisting the tip under the cap. On 5–passenger vehicles, the carpeted floor lid can be used as a kneeling pad. 3. Loosen each wheel lug nut by half a turn, but do not remove them until the wheel is raised off the ground.

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

323

Roadside Emergencies

4. Assemble the jack handle extension on the lug nut wrench by sliding the square end of the jack handle through the plastic grommet on the lug nut wrench and into the square hole on the other side.

5. Position the jack according to the illustrated guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board underbody mounts to lift the vehicle with the jack.

324

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

WARNING: To lessen the risk of personal injury, do

not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.

• Never use the front or rear differential as a jacking point. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts, cone side in, until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 8. Lower the wheel by turning the jack handle counterclockwise. 9. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification.

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing up, toward the vehicle. 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center. Pull on the cable to align the components at the end of the cable. 3. Turn the lug wrench clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle

325

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness. Tighten to the best of your ability, to the point where the ratchet/slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, take the vehicle to your authorized dealer for assistance at your earliest convenience. 4. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary. Failure to properly stow the spare tire may result in failure of the winch cable and loss of the tire. 5. If your vehicle is equipped with a spare tire lock and key, be sure to install the spare tire lock into the bumper drive tube with the spare tire lock key and jack handle. 6. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, per scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. Re-stowing the jack and tools 1. Unblock the wheels. 2. Stow the wheel ornament (if removed) in a safe location in the vehicle (such as the glove box or jack stowage compartment) so it will not become damaged. Re-install the wheel ornament onto the wheel once the tire is repaired or replaced. 3. Stow the jack and tools in their respective locations, making sure they are fully secured so they do not rattle when you drive.

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.).

Lug nut socket size/Bolt size

Wheel lug nut torque*

N•m 135

lb.ft. 100

Lug nut socket size: 3⁄4
inch (19 mm) hex Bolt size: 1⁄2 x 20
* Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.

326

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting

surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control.

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger. DO NOT apply grease to lugnut/stud holes or wheel-to-brake surfaces.

RUNNING OUT OF FUEL If you have run out of fuel and need to refill the vehicle with a portable fuel container, see Running out of fuel in the Maintenance and Specifications chapter for proper fuel filling method using a portable fuel container and the included fuel filler funnel. Do not insert the nozzle of portable fuel containers or any type of aftermarket funnels into the Easy Fuel™ “no cap” fuel system as it can be damaged. You must use the included funnel in such circumstances.

WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel™ system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, all of which could result in serious personal injury.

327

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

JUMP STARTING

WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could

result in injury or vehicle damage.

WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.

Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage.

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off.

328

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Connecting the jumper cables

Roadside Emergencies

+–

+–

1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.

+–

+–

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.

329

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

+–

+–

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.

+-

4. Make the final connection of the negative (-) cable to the ground stud located toward the front of the vehicle (forward of the battery) on the radiator support. Keep the negative (-) cable away from the battery and the carburetor/fuel injection system.

330

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

Note: Do not attach the negative (-) cable fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.

WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may

cause an explosion of the gases that surround the battery.

5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.

+–

+–

2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.

331

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

+–

+–

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.

+–

+–

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.

332

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

WRECKER TOWING

Roadside Emergencies

Note: Turn off the power running boards (if equipped) prior to preparing the vehicle for towing. Refer to Power deployable running boards in the Driver Controls chapter. If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If the vehicle’s battery is discharged, refer to Automatic transmission operation in the Driving chapter for directions on how to move the gearshift lever out of the P (Park) position, for proper towing. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground.

333

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Roadside Emergencies

On 4x4/AWD vehicles, it is required that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground. If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.

Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer, or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • Vehicle is facing forward so that it is being towed in a forward • Place the transmission in N (Neutral). Refer to Brake-shift interlock in the Driving chapter for specific instructions if you cannot move the gear shift lever into N (Neutral).

direction.

• Maximum speed is not to exceed 35 mph (56 km/h). • Maximum distance is 50 miles (80 km).

334

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft威 parts, or remanufactured or other parts that are authorized by Ford.

Away from home If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer. In the United States: Mailing address Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
Telephone 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) Online Additional information and resources are available online at www.genuineservice.com. • U.S. dealer locator by Dealer Name, City/State, or Zip Code • Owner Guides • Maintenance Schedules • Recalls • Ford Extended Service Plans • Ford Genuine Accessories • Service specials and promotions.

335

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
Telephone 1-800-387-9333
Online www.lincolncanada.com Additional assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. 2. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. 3. If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center In order to help you serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number (VIN) • Your telephone number (home and business) • The name of the authorized dealer and city where located • The vehicle’s current odometer reading In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. 336

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.

IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step

337

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation and your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. You are not bound by the decision, but should you choose to accept the BBB AUTO LINE decision, Ford must abide by the accepted decision as well. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. BBB AUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800
Arlington, Virginia 22203–1833
BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). 338

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
Email: [email protected]

339

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

If you are in another foreign country, contact the nearest authorized dealer. If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations. Customers in the U.S. should call 1-800-392-3673.

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207
Or to order a free publication catalog, call toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.)

Obtaining a French Owner’s Guide French Owner’s Guides can be obtained from your authorized dealer or by writing to: Ford Motor Company of Canada, Limited Service Publications CHQ202
The Canadian Road P.O. Box 2000
Oakville, ON, Canada L6J 5E4

340

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Customer Assistance

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from http://www.safercar.gov.

REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada, using their toll-free number: 1–800–333–0510.

341

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing

or laundry liquid. These products can discolor and spot painted surfaces.

strong, direct sunlight.

• Never wash a vehicle that is “hot to the touch” or during exposure to • Always use a clean sponge or car wash mitt with plenty of water for • Dry the vehicle with a chamois or soft terry cloth towel in order to • It is especially important to wash the vehicle regularly during the

eliminate water spotting.

best results.

winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Motorcraft威 Bug and Tar Remover (ZC-42), which is available from your authorized dealer. • Remove any exterior accessories, such as antennas, before entering a • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.

• If your vehicle is equipped with running boards, do not use rubber, plastic and vinyl protectant products on the running board surface, as the area may become slippery.

car wash.

shampoo, such as Motorcraft威 Detail Wash (ZC-3-A).

Exterior chrome • Wash the vehicle first, using cool or lukewarm water and a neutral pH • Use Motorcraft威 Custom Bright Metal Cleaner (ZC-15), available from your authorized dealer. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag. • Never use abrasive materials such as steel wool or plastic pads

as they can scratch the chrome surface.

342

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft威 Premium

Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product.

• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.

spots, road salt and industrial fallout before repairing paint chips.

PAINT CHIPS Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft威 Wheel and Tire Cleaner (ZC-37-A), which is available from your authorized dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water.

• Never apply any cleaning chemical to hot or warm wheel rims or • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.

• Do not use hydrofluoric acid-based or high caustic-based wheel • To remove tar and grease, use Motorcraft威 Bug and Tar Remover

cleaners, steel wool, fuels or strong household detergent.

covers.

(ZC-42), available from your authorized dealer.

343

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning

engine block or other engine components.

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the • Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft威 Engine Shampoo (CXC-66-A). • Cover the highlighted areas to prevent water damage when cleaning • Never wash or rinse the engine while it is running; water in the • Never wash or rinse any ignition coil, spark plug wire or spark plug

running engine may cause internal damage.

the engine.

well, or the area in and around these locations.

4.0L V6 ENGINE

344

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

4.6L V8 ENGINE

Cleaning

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft威 Bug and Tar

Remover (ZC-42).

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Motorcraft威 Ultra-Clear Spray Glass Cleaner (ZC-23) in the U.S., or Premium Quality Windshield Washer Fluid [CXC-37-(A, B, D, or F)] in Canada, available from your authorized dealer.

345

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning • The wiper blades can be cleaned with isopropyl (rubbing) alcohol or

Motorcraft威 Premium Windshield Washer Concentrate (ZC-32-A), available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly.

• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water. Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines.

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.

• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the

finish of the instrument panel, interior trim and cluster lens.

WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid

contamination of the airbag system.

346

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning

If a staining liquid like coffee/juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white cotton cloth. For more thorough cleaning, use a mild soap and water solution. If the spot cannot be completely cleaned by this method, the area may be cleaned using a commercially available cleaning product designed for automotive interiors. 3. If necessary, apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area–allow this to set at room temperature for 30 minutes. 4. Remove the soaked cloth, and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth.

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft威 Professional Strength • If grease or tar is present on the material, spot-clean the area first with Motorcraft威 Spot and Stain Remover (ZC-14). In Canada, use Motorcraft威 Multi-Purpose Cleaner (CXC-101).

Carpet & Upholstery Cleaner (ZC-54).

immediately (but do not oversaturate) or the ring will set.

• If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.

WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt

webbing.

WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a collision.

347

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • For routine cleaning, wipe the surface with a soft, damp cloth. For

more thorough cleaning, wipe the surface with a mild soap and water solution. In Canada, use Motorcraft威 Vinyl Cleaner (CXC-93). Dry the area with a soft cloth.

• If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product designed for automotive leather.

• Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear, protective coating.

Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining.

UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft威 Bug and Tar Remover (ZC-42) Motorcraft威 Custom Bright Metal Cleaner (ZC-15) Motorcraft威 Custom Clear Coat Polish (ZC-8-A) Motorcraft威 Detail Wash (ZC-3-A) Motorcraft威 Dusting Cloth (ZC-24) Motorcraft威 Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft威 Engine Shampoo (Canada only) (CXC-66-A) Motorcraft威 Multi-Purpose Cleaner (Canada only) (CXC-101) 348

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Cleaning

Motorcraft威 Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft威 Premium Liquid Wax (ZC-53-A) Motorcraft威 Premium Windshield Washer Concentrate (U.S. only) (ZC-32-A) Motorcraft威 Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft威 Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft威 Tire Clean and Shine (ZC-28) Motorcraft威 Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft威 Vinyl Cleaner (Canada only) (CXC-93) Motorcraft威 Wheel and Tire Cleaner (ZC-37-A)

349

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

service.

SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine • Use only recommended fuels, lubricants, fluids and service parts • Your authorized dealer can provide parts and service.

conforming to specifications.

PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed • Keep all open flames and other lit material away from the battery and

space, unless you are sure you have enough ventilation.

all fuel related parts.

WARNING: Turn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object

under the vehicle. Never place your hand between the extended running board and the vehicle. A moving running board may cause injury.

Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly.

Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels.

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running.

350

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.

2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood.

351

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT

4.0L V6 engine

1. Engine oil filler cap 2. Engine oil dipstick (out of view) 3. Brake fluid reservoir 4. Power distribution box 5. Battery 6. Power steering fluid reservoir 7. Radiator cap 8. Engine coolant reservoir 9. Air filter assembly 10. Washer fluid reservoir

352

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

4.6L V8 engine

1. Air filter assembly 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Power steering fluid reservoir 8. Radiator cap 9. Engine coolant reservoir 10. Windshield washer fluid reservoir

2010 Explorer (exp) Owners Guide, 2nd Printing USA (fus)

353

Maintenance and Specifications

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely.

Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to the Maintenance product specifications and capacities section in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.

WARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure

to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components.