2002 Ford Expedition Owners Manual

BASS

TREB

SEL

BAL

FADE

CD

TAPE

EJ

RDS

DSP

MUTE

SEEK

TUNE

SCAN

AUTO

AM

FM

REW

FF

SIDE 1.2

COMP

SHUFF

18

Entertainment systems

Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.

Volume/power control Press the control to turn the audio system on or off.

Turn the control to raise or lower volume.

VOL PUSH ON

VOL PUSH ON

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Speedsensitivevolume(ifequipped) With this feature, radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. The recommended level for speed sensitive volume is from level 1
through level 3. Level 0 turns the speed sensitive volume off and level 7
is the maximum setting. With the radio on, press and hold the volume control for five seconds, until the display reads SPEED VOL, then press:

VOL PUSH ON

19

(cid:83)(cid:69)(cid:76)

BASS

TREB

BASS

TREB

BAL

FADE

SEL

SEL

SEL

Entertainment systems

• •

to increase volume

compensation

to decrease or shut off the

volume compensation

Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass.

Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble.

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers.

20

Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.

Entertainment systems

BAL

FADE

SEL

Seek function The seek function control works in radio, tape or CD mode (if equipped). Seekfunctioninradiomode • Press

to find the next listenable station up the frequency band.

SEEK

SEEK

to find the next listenable station down the frequency band.

• Press Seekfunctionintapemode • Press

to listen to the previous selection on the tape or return to the beginning of the current selection.

• Press SeekfunctionforCDchanger • Press

to seek to the previous

track of the current disc. If a selection has been playing for three seconds or more and you press that selection from the beginning.

• Press

SEEK

, the CD changer will replay

to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.

to listen to the next selection on the tape.

21

Entertainment systems

Scan function The scan function works in radio, tape or CD mode (if equipped).

SCAN

Scanfunctioninradiomode Press the SCAN control to activate scan mode and to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to disengage scan mode. Scanfunctionintapemode Press the SCAN control to hear a short sampling of all selections on the tape. The tape will scan in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape. To stop on a particular selection, press the SCAN control again. ScanfunctioninCDmode Press the SCAN control to hear a short sampling of all selections on the CD. The CD will scan in a forward direction, wrapping back to the first track at the end of the CD. To stop on a particular selection, press the control again.

AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped).

AM

FM

AM/FMselectinradiomode The AM/FM control allows you to select AM or FM frequency bands. Press the control to toggle between AM, FM1 or FM2 memory preset stations. AM/FMselectintapemode Press this control to stop tape play and begin radio play.

22

Entertainment systems

AM/FMselectinCDmode Press this control to stop CD play and begin radio play.

Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Settingmemorypresetstations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.

REW

FF

SIDE 1.2

COMP

SHUFF

Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Startingautosetmemorypreset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the control again.

AUTO

23

Entertainment systems

Setting the clock with radio data system (RDS) feature Press the RDS control until SELECT HOUR or SELECT MINS is displayed.

RDS

DSP

Use the SEL control to manually set the time. • Press • Press

hours/minutes.

to decrease

to increase

hours/minutes.

(cid:83)(cid:69)(cid:76)

Tune adjust The tune control works in radio or CD mode (if equipped). Tuneadjustinradiomode • Press

to move to the next

frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.

TUNE

• Press

to move to the next frequency up the band (whether or not

a listenable station is located there). Hold for quick movement.

TuneadjustforCDchanger • Press

to select the previous

disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs.

TUNE

to select the next disc in the CD changer. Hold the control

to fast-forward through the remaining discs.

• Press

24

Entertainment systems

Tape/CD select • To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.

TAPE

CD

• To begin CD play (if equipped with CD changer), ensure that the CDs are loaded. Press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

TAPE

CD

Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will

continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds

results in slow rewind. Pressing the control for more than three seconds results in fast rewind.

Fast forward The fast forward control works in tape and CD modes (if equipped). • In the tape mode, tape direction will automatically reverse when the end of the tape is reached.

• In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action.

REW

FF

25

Entertainment systems

Tape direction select Press SIDE 1–2 to play the alternate side of a tape.

Eject function Press the control to stop and eject a tape.

SIDE 1-2

EJ

Dolby姞 noise reduction Dolby威 noise reduction operates only in tape mode. Dolby威 noise reduction reduces the amount of hiss and static during tape playback. Press the reduction. The Dolby威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby威 and the double-D symbol are registered trademarks of Dolby威 Labratories Licensing Corporation.

control to activate (and deactivate) Dolby威 noise

Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. The effect of the feature varies with the music content.

COMP

26

Entertainment systems

Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again.

SHUFF

Mute mode Press the control to mute the playing media. Press the control again to return to the playing media.

MUTE

Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio stations. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. Press the RDS control until RDS ON or RDS OFF appears in the display.

RDS

Use the SEL control to enable (ON) or disable (OFF) the feature. With the RDS activated, press the SEL control to scroll through the following selections:

Traffic • Press the RDS control until

TRAFFIC is displayed.

(cid:83)(cid:69)(cid:76)

RDS

27

Entertainment systems • Use the SEL control to select ON or OFF. With the feature on, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data).

(cid:83)(cid:69)(cid:76)

Traffic information is not available in most U.S. markets. Programtype • Press the RDS control until the FIND program type is displayed. • Use the SEL control to select the

RDS

program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections:

• Classic • Country • Info • Jazz • Oldies • R & B • Religious • Rock • Soft • Top 40
Show • With RDS activated, press the

RDS control until SHOW is displayed.

28

(cid:83)(cid:69)(cid:76)

RDS

Entertainment systems

• Use the SEL control to select TYPE (the display shows the program type), NAME (the display shows the call letters of the station) or NONE.

(cid:83)(cid:69)(cid:76)

DSP

RDS

Digital signal processing (if equipped) The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes. These effects will change the sound quality and may need to be adjusted based upon the program material to suit your listening needs. Press the control to turn the feature on or off. Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: • JAZZ CLUB—jazz club with • HALL—rectangular concert hall capacity of about 2 000
• CHURCH—church with a high vault. • STADIUM—outdoor stadium with a capacity of about 30 000. • NEWS—“voice-only” type of sound with a limited audio band. Press the DSP control until one of the following appears: • ALL SEATS • DRIVER SEAT • REAR SEATS

clearly reflected sounds.

RDS

DSP

(cid:83)(cid:69)(cid:76)

29

Entertainment systems

Use the SELECT control to change the equalization to the desired mode.

PREMIUM AM/FM STEREO/SINGLE CD RADIO

VOL PUSH ON

CD

(cid:83)(cid:69)(cid:76)

BASS

TREB

BAL

FADE

SEL

EJ

MUTE

SCAN

SEEK

TUNE

AUTO

RDS

AM

FM

REW

FF

COMP

SHUFF

Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.

30

Entertainment systems

Volume/power control Press the control to turn the audio system on or off.

Turn the control to raise or lower volume.

VOL PUSH ON

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Speedsensitivevolume(ifequipped) With this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. The recommended level for speed sensitive volume is from level 1
through level 3. Level 0 turns the speed sensitive volume off and level 7
is the maximum setting. With the radio on, press and hold the volume control for five seconds, then press:

31

Entertainment systems

• •

to increase volume

compensation

to decrease or shut off the

volume compensation

Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.

Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.

Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.

32

(cid:83)(cid:69)(cid:76)

BASS

TREB

BASS

TREB

BAL

FADE

BAL

FADE

SEL

SEL

SEL

SEL

Entertainment systems

Seek function The seek function control works in radio, CD and CD changer mode (if equipped). Seekfunctioninradiomode • Press

to find the next listenable station down the frequency band.

to find the next listenable station up the frequency band.

• Press SeekfunctionforCDorCDchanger(ifequipped) • Press

to seek to the previous

SEEK

SEEK

, the CD changer will replay

track of the current disc. If a selection has been playing for three seconds or more and you press that selection from the beginning.

• Press

to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.

Scan function The scan function works in radio, CD and CD changer mode (if equipped).

SCAN

Scanfunctioninradiomode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. ScanfunctioninCDmode Press the SCAN control to hear a short sampling of all selections on the CD (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.). To stop on a particular selection, press the control again.

33

Entertainment systems

AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped).

AM

FM

AM/FMselectinradiomode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FMselectinCDorCDchangermode(ifequipped) Press this control to stop CD play and begin radio play.

Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Settingmemorypresetstations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.

REW

FF

COMP

SHUFF

Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations.

34

Entertainment systems

Startingautosetmemorypreset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO control again.

AUTO

Setting the clock Press the RDS control until SELECT HOUR or SELECT MINS is displayed.

Use the SEL control to manually set the time. • Press • Press

to decrease hours/

to increase hours/

minutes.

minutes.

RDS

(cid:83)(cid:69)(cid:76)

Tune adjust The tune control works in radio or CD changer mode (if equipped). Tuneadjustinradiomode • Press

to move to the next

frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.

TUNE

• Press

to move to the next frequency up the band (whether or not

a listenable station is located there). Hold for quick movement.

35

Entertainment systems

TuneadjustforCDchanger • Press

to select the previous

disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc.

TUNE

to select the next disc in the CD changer. Hold the control

to fast-forward through the remaining discs.

• Press

CD select To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. Press the CD control again to toggle between CD and CD changer mode (if equipped). Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind.

Rewind The rewind control works in CD mode. • In CD mode, pressing the REW

Fast forward The fast forward control works in CD mode. • In CD mode, pressing the control

REW

FF

for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action.

Eject function Press the control to stop and eject a CD.

EJ

36

Entertainment systems

Compression feature (if equipped) Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.

COMP

Shuffle feature (if equipped) The shuffle feature operates in CD changer mode and plays all tracks on the current disc in random order. The shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again.

SHUFF

Mute mode Press the control to mute the playing media. Press the control again to return to the playing media.

MUTE

Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio station. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. Press the RDS control until RDS ON or RDS OFF appear in the display. Use the SEL control to enable (ON) or disable (OFF) the feature. Once activated, you can choose from the following items:

RDS

37

RDS

(cid:83)(cid:69)(cid:76)

RDS

(cid:83)(cid:69)(cid:76)

Entertainment systems

Traffic • Press the RDS control until

TRAFFIC is displayed.

• Use the SEL control to select ON or OFF. With the feature on, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data).

Programtype • Press the RDS control until FIND

program type is displayed.

• Use the SEL control to select the

program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections:

• Classic • Country • Info • Jazz • Oldies • R & B • Religious • Rock • Soft • Top 40

38

Entertainment systems

Show • With RDS activated, press the

RDS control until SHOW is displayed.

• Use the SEL control to select

TYPE, NAME or NONE.

RDS

(cid:83)(cid:69)(cid:76)

REAR SEAT CONTROLS (IF EQUIPPED) The Personal Audio System, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously. However, the front and middle-seat passengers cannot listen to two different radio stations at the same time.

- VOLUME +

MODE

SEEK

MEMORY

REW

FF

SIDE 1.2

COMP

SHUFF

will appear in the display.

To turn on the rear seat controls, press the memory preset controls 3
and 5 at the same time. The Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audio controls, (such as both trying to listen to the same playing media), the front audio system will receive the desired selection.

39

Entertainment systems

To activate the Personal Audio System, press the speaker/headphone control. Press the MODE control to change audio sources (for headphone mode only). Use the SEEK, VOLUME and MEMORY controls to make adjustments to the playing media.

ADJUSTING THE VOLUME Press the + control to increase volume. Press the - control to decrease volume.

- VOLUME +

MODE

SEEK

MEMORY

- VOLUME +

MODE

SEEK

MEMORY

From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning the rear speakers on and off.

TURNING THE REAR SPEAKERS ON AND OFF Press to turn the rear speakers on or off.

- VOLUME +

MODE

SEEK

MEMORY

40

Entertainment systems

jack. Press the

USING HEADPHONES/PERSONAL AUDIO SYSTEM Plug a 3.5 mm headphone (not included) into the speaker on/off control to operate the headphones. DUAL PLAY illuminates in the radio display and the fade control is disabled. The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones (Personal Audio System). SINGLE PLAY illuminates in the radio display and the fade control is enabled. For the Personal Audio System to be enabled, the rear seat controls must be active and

illuminated in the radio display.

MODE SELECT Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). If in the Personal Audio System mode, SHARED illuminates in the radio display when the front and rear modes are set to the same media.

MEMORY PRESET CONTROL Push the MEMORY control successively to allow rear seat passengers to scroll through the 6
memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc.

- VOLUME +

MODE

SEEK

MEMORY

- VOLUME +

MODE

SEEK

MEMORY

41

Entertainment systems

SEEK FUNCTION • In radio mode, press to find the next listenable station down the frequency band. • In radio mode, press

to find the next listenable station up the frequency band.

• In tape mode, use the SEEK function to access the next previous

selection.

• In CD mode (if equipped), use

or

the SEEK function to access the next

- VOLUME +

MODE

SEEK

MEMORY

or previous

selection.

CD CHANGER (IF EQUIPPED) Your CD changer is located in the center console. Slide the door to access the CD changer magazine.

Press

to eject the magazine.

42

Entertainment systems

1. Pull the lever to remove a CD tray from the magazine.

2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing up. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine.

3. Insert each CD tray, with the disc loaded, all the way into the CD magazine.

4. Insert the CD magazine into the changer.

43

Entertainment systems

5. Slide the door to the left to close.

Use only compact discs containing this mark.

The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

TROUBLESHOOTING THE CD CHANGER (IF EQUIPPED)

The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case.

If sound skips: • You may be traveling on a rough road, playing badly scratched discs or

the disc may be dirty. Skipping will not scratch the discs or damage the player.

If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc. • The disc is inserted with the label surface downward. • The disc is dusty or defective. • A disc with format and dimensions not within industry standards is

inserted.

44

Entertainment systems

CLEANING COMPACT DISCS Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion.

CD AND CD CHANGER CARE • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended • Do not insert more than one disc into each slot of the CD changer

periods of time.

magazine.

Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

CLEANING CASSETTE PLAYER (IF EQUIPPED) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation.

CASSETTE AND CASSETTE PLAYER CARE • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity, extreme heat or

extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. • Tighten very loose tapes by inserting a finger or pencil into the hole • Remove loose labels before inserting tapes. • Do not leave tapes in the cassette player for a long time when not

and turning the hub.

being played.

45

Entertainment systems

RADIO FREQUENCY INFORMATION The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area.

RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.

• Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.

• Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.

The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.

AUDIO SYSTEM WARRANTIES AND SERVICE Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or a qualified technician.

46

Climate controls

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED)

LO

HI

PANEL

OFF

PANEL & FLOOR

FLOOR

FLR & DEF

DEF

COOL

WARM

Fan speed control Controls the volume of air circulated in the vehicle.

Temperature control knob Controls the temperature of the airflow inside the vehicle.

LO

HI

COOL

WARM

A/C

OFF

PANEL

FLOOR

MAX A/C

PANEL & FLOOR

Mode Selector Control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor can operate in all modes except PANEL and FLOOR. However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. • MAX A/C – Uses recirculated air to cool the vehicle. MAX A/C is

FLR & DEF

DEF

noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.

47

Climate controls • A/C – Uses outside air to cool the vehicle. It is quieter than MAX A/C

but not as economical. Airflow will be from the instrument panel registers.

• PANEL – Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.

• OFF – Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle.

• PANEL & FLOOR – Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. • FLOOR – Allows for maximum heating by distributing outside air

through the floor ducts. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. • FLR & DEF – Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.

– Distributes outside air through the windshield defroster

ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.

• DEF

Operating tips • In humid weather conditions, place the climate control system in

Defrost mode before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired.

48

Climate controls

• To reduce humidity buildup inside the vehicle in cold weather

conditions, don’t drive with the climate control system in the OFF or MAX A/C position.

• To reduce humidity buildup inside the vehicle in warm weather

conditions, don’t drive with the climate control system in the OFF position.

• Under normal weather conditions, your vehicle’s climate control system should be left in any position other than the MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.

• If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Once the vehicle has been “aired out”, operate the climate control system as desired.

airflow to the rear seats (if equipped).

bottom of the windshield and underneath the hood).

• Do not put objects under the front seat which may interfere with the • Remove any snow, ice or leaves from the air intake area (at the • Do not place objects over the defroster outlets. These objects can block airflow and reduce visibility through your windshield. Avoid placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow, in addition to, damaging the climate control system.

To aid in side window defogging/demisting in cold weather conditions: 1. Select the position that distributes air through the Panel and Floor. 2. Set the temperature control to full heat. 3. Set the fan speed to full fan. 4. Direct the outer panel vents towards the side windows. 5. To increase airflow to the outer panel vents, close the central panel vents.

49

Climate controls

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC) SYSTEM (IF EQUIPPED) The EATC system will maintain a selected temperature and automatically control airflow. You can override automatic operation with any of the override controls, the fan speed control or the steering wheel controls (if equipped).

OUTSIDE TEMP

AUTOMATIC

PNL • FLR

FLR • DEF

MAX A/C

AUTO

FLOOR

VENT

DEF

OFF

Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running.

Turning the EATC system off Press OFF. The outside temperature function will continue to operate until the ignition is turned off.

OUTSIDE TEMP

AUTO

OFF

AUTOMATIC

MAX A/C

VENT

PNL • FLR

FLOOR

FLR • DEF

DEF

OFF

AUTOMATIC

FLR • DEF

DEF

HI

LO

HI

LO

HI

LO

Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if outside air or recirculated air is required. Fan speed remains automatic unless the fan speed thumbwheel is turned or the steering wheel fan speed control (if equipped) is pressed.

50

Climate controls

When in AUTOMATIC and weather conditions require heat, air will be sent to the floor. However, if the engine is not warm enough to provide heat, the fan will be at a low speed and the air will be directed to the windshield. In approximately 31⁄2 minutes or less, the fan speed will start to increase and the airflow location will change to the floor area. If unusual conditions exist (i.e.-window fogging, etc.), the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary.

Temperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons.

) if automatic fan speed is not desired.

˚F AUTO

OUTSIDE TEMP

MAX A/C

VENT

PNL • FLR

For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the red control. For continuous maximum heating, push the red button until 32°C (90°F) is shown in the display window. The EATC will continue maximum heating (disregarding the displayed temperature) until a cooler temperature is selected by pressing the blue control.

51

Climate controls

Temperature conversion at Press MAX A/C and DEF the same time (for one second) to switch between Fahrenheit and Celsius. The English/Metric (E/M) control on the trip computer and message center (if equipped) will not change temperature display.

OUTSIDE TEMP

AUTOMATIC

PNL • FLR

FLR • DEF

MAX A/C

AUTO

FLOOR

VENT

DEF

OFF

Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel or press the steering wheel controls (if equipped) up for higher fan speed or down for lower fan speed. The display will show indicate manual fan operation.

to

˚F AUTO

To return to automatic fan operation, press AUTOMATIC.

Manual override controls The manual override controls allow you to determine where airflow is directed. To return to full automatic control, press AUTOMATIC.

OUTSIDE TEMP

AUTO

OFF

AUTOMATIC

MAX A/C

VENT

PNL • FLR

FLOOR

FLR • DEF

DEF

HI

LO

HI

LO

The air conditioning compressor can operate in all modes except FLOOR and VENT. It will also operate only when required when AUTOMATIC has been selected. However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.

52

Climate controls • MAX A/C-Uses recirculated air to cool the vehicle. The temperature

will display 16°C (60°F). To exit, press AUTOMATIC or any other override controls. MAX A/C is louder than normal A/C but more economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • VENT-Distributes outside air through the instrument panel registers.

However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode.

• PNL•FLR-Distributes outside air through the instrument panel

registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. • FLOOR-Distributes outside air through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode. • FLR•DEF-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.

-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the outside air temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. • OFF-Outside air is shut out and the fan will not operate. For short

periods of time only, use this mode to reduce undesirable odors from entering the vehicle.

• DEF

53

Climate controls

Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again.

OUTSIDE TEMP

MAX A/C

VENT

PNL • FLR

If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window. If a manual override function is selected while the outside temperature is displayed, the new function will be displayed for four seconds after it is changed, then the outside temperature will return to the window along with the override selection. The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations.

Operating tips • In humid weather conditions, place the climate control system in DEF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired.

• To reduce humidity buildup inside the vehicle in cold weather

conditions, don’t drive with the climate control system in the OFF or MAX A/C position.

• To reduce humidity buildup inside the vehicle in warm weather

conditions, don’t drive with the climate control system in the OFF position.

• Under normal weather conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct.

54

Climate controls

• Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.

• If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Once the vehicle has been “aired out”, operate the climate control system as desired. • Don’t put objects under the front seat that will interfere with the • Remove any snow, ice or leaves from the air intake area at the base of • Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Avoid placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow, in addition to damaging the climate control system.

airflow to the rear seats.

the windshield.

To aid in side window defogging/demisting in cold weather conditions: 1. Select PNL • FLR 2. Set the temperature control to full heat 3. Set the fan speed control to HI 4. Direct the outer panel vents towards the side windows. To increase airflow to the outer panel vents, close the central panel vents.

Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.

AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED) Depending on your equipment package, your vehicle may be equipped with auxiliary A/C-heater controls. The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle. Besides the driver’s control panel for the front seat occupants, the second row auxiliary A/C-heater controls allow the rear passengers to control the

55

Climate controls

temperature in the rear of the vehicle through a second control panel above the second row, or in the floor console. If your vehicle is equipped with auxiliary A/C controls, they may be located in the floor console,

FLO O R

PANEL

W A R M

R E A

O F F

HI

O L

C O

or located in the overhead console. If your vehicle is equipped with a moon roof and a navigation system, you will not have a front auxiliary A/C- heater control console. All operation is obtained through the rear auxiliary A/C-heater control console.

56

Climate controls

OFF

REAR

In order for the auxiliary A/C-heater controls (if equipped) to function, the driver’s auxiliary A/C-heater control must be set to REAR, unless your vehicle is equipped with a moonroof and a navigation system. In which case, the rear auxiliary A/C-heater control console serves as the main control for the auxiliary climate control system. The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate.

WARM PANEL

PANEL & FLOOR

FLOOR

FLR & DEF

COOL

MAX A/C

FLOOR

PANEL

LO

HI

OFF

A/C

HI

COOL

WARM

DEF

When the auxiliary A/C-heater control is set to FLOOR, airflow only occurs from the third row seat floor vent located in the driver’s side rear quarter trim panel. When the auxiliary A/C-heater control is set to PANEL, airflow occurs from the overhead 2nd and 3rd row vents. Turn the fan speed control knob to the desired speed.

OFF

LO

HI

COOL

WARM

Turn the temperature control to the desired temperature. You can get warm or cool air through either the overhead registers or floor vent by turning the auxiliary mode selector: • Far left for airflow to the overhead registers. • Far right for airflow to the rear floor vent. • Anywhere between PANEL and FLOOR to vary airflow between the outlets.

PANEL

FLOOR

57

Climate controls

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when

the rear defroster is activated.

The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before 10 minutes have passed, push the control again.

58

Lights

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps.

Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp indicator light will illuminate.

Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20
seconds after the ignition switch is turned to OFF. • To turn autolamps on, rotate the • To turn autolamps off, rotate the control clockwise to OFF. • Foglamps are not controlled by the autolamps. In order to turn on the

control counterclockwise.

foglamps, you must turn the lamp switch to the pull toward you for foglamps.

position and

59

Lights

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or Parking lamps position.

Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

High beams • Push forward to activate. • Pull toward you to deactivate.

Flash to pass Pull toward you to activate and release to deactivate.

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. • Rotate to full down position (past detent) to turn off interior lamps.

60

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician.

Lights

TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn

turn signal.

signal.

INTERIOR LAMPS Map lamps With trip computer

VENT

ROOF

VENT

61

Lights

Without trip computer

AUTO

ROOF

To turn on the map lamps, press the control next to each lamp.

Rear dome lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmer

switch is held up until the courtesy lamps come on.

• any of the remote entry controls are pressed and the ignition is OFF.

With the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control.

BULBS

Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Foglamps • High-mount brakelamp • Brakelamps • Parking lamps • Turn signals

62

Lights

• License plate lamp • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance.

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

Function

Number of bulbs

Trade number

9005

9006

Headlamps (low-beam) Headlamps (high-beam) Front park/turn lamps Foglamps Dome/map lamps Turn/tail/brake lamps Liftgate lamp Backup lamp License lamp High-mount brake lamp Running board lamp (if equipped) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer

3457 K 899
579
3157
916
3156
168
W5W

168

63

Lights

Replacing the interior bulbs Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician. Maplamps To change the map lamp bulbs: 1. Use a small screwdriver to remove the map lamp lens. 2. To remove the old bulb, twist 1⁄4
turn and pull it out. 3. Twist in a new bulb. 4. Align and press the map lamp lens back on and test the lamp operation.

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. At the back of the headlamp, pull clips rearward and up to release the headlamp assembly. 4. Slide headlamp assembly forward and off of guide ribs to expose the back of the bulb and wiring connector.

64

Lights

5. Disconnect the electrical connector from the bulb by pulling rearward. 6. Remove bulb retainer ring by turning it counterclockwise, then slide the ring off the plastic base. 7. Without turning, carefully pull bulb assembly out of headlamp assembly.

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

8. Insert the glass end of the new bulb into the headlamp assembly. When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 9. Install bulb retaining ring over the plastic base and lock the ring into the socket by turning it clockwise until you feel a “stop.” 10. Connect the electrical connector into the plastic base until it “snaps.” 11. Straighten alignment pins, making them parallel with the outer edges of the attachment standoff. 12. Carefully insert the headlamp assembly into the vehicle making sure the alignment pins are inserted into the proper holes and into the guide ribs. 13. Hold the headlamp assembly snugly against the vehicle and push down on the clips to lock the lamp into place.

65