2014 Ford Escape Owners Manual

Disarm the alarm by any of the following actions: • Unlock the doors or luggage

compartment with the remote control or keyless entry keypad. Switch the ignition on or start the vehicle.

•

• Use a key in the driver’s door to unlock the vehicle, then switch the ignition on within 12 seconds.

Note: Pressing the panic button on the remote control will stop the horn and signal indicators, but will not disarm the system.

65

Steering Wheel

ADJUSTING THE STEERING WHEEL

WARNING

Do not adjust the steering wheel when your vehicle is moving.

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 110).

3. Lock the steering column. AUDIO CONTROL (If Equipped) Select the required source on the audio unit. You can operate the following functions with the control:

1. Unlock the steering column. 2. Adjust the steering wheel to the desired

position.

66

Escape (TM2) , enUSA

122E951783E95179Steering Wheel

Type 1

Type 2

Volume up Seek up or next Volume down Seek down or previous

Seek, Next or Previous Press the seek button to: •

tune the radio to the next or previous stored preset play the next or the previous track.

• Press and hold the seek button to: •

tune the radio to the next station up or down the frequency band seek through a track.

Volume up Seek up or next Volume down Seek down or previous Mode

Press M to select the audio source.

•

67

Escape (TM2) , enUSA

E129462BDCAECDABE129463Steering Wheel

VOICE CONTROL (If Equipped)

CRUISE CONTROL

See Cruise Control (page 160). INFORMATION DISPLAY CONTROL

Pull the control to select or deselect voice control. See SYNC™ (page 289). See MyFord Touch™ (page 324). MyFord Touch® Controls (If Equipped) Your steering wheel controls may also have these additional features.

Press to go to the home screen.

Press to go to the information screen.

See MyFord Touch™ (page 324).

See Information Displays (page 89).

68

Escape (TM2) , enUSA

E161798E142613E142608E142437E130248Steering Wheel

Multimedia Controls (If Equipped)

Use the arrows on the right side of the steering wheel to navigate through the menus. Press OK to make a selection.

69

Escape (TM2) , enUSA

E145434Wipers and Washers

WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

Single wipe Intermittent wipe Normal wipe High speed wipe

Intermittent Wipe

Short wipe interval Intermittent wipe Long wipe interval

Use the rotary control to adjust the intermittent wipe interval. Speed dependent wipers (if equipped) When your vehicle speed increases, the interval between wipes will decrease. AUTOWIPERS (If Equipped) Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: If you switch on the autolamps with the autowipers, the low beam headlamps will turn on automatically when the rain sensor turns on the windshield wipers continuously.

70

Escape (TM2) , enUSA

E168040E168041Wipers and Washers

Keep the outside of the windshield clean. The rain sensor is very sensitive. Dirt or debris around the interior rear view mirror area will affect the autowipers' performance. For example, the autowipers may turn on if dirt, mist or insects hit the windshield. WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat.

To operate the washers and spray the windshield, pull the lever toward you. When you release the lever, the wipers will operate for a short time.

Note: During wet or winter driving conditions with ice, snow or a salty road mist, inconsistent or unexpected wiping or smearing may occur. In these conditions, you can do the following: •

Lower the sensitivity of the autowipers to reduce the amount of smearing. Switch to normal or high-speed wipe. Switch the autowipers off.

• •

High sensitivity On Low sensitivity

The autowipers feature uses a rain sensor that is located in the area around the interior rear view mirror. The rain sensor monitors the amount of moisture on the windshield and automatically turns the wipers on. It will adjust the wiper speed by the amount of moisture that the sensor detects on the windshield. Use the rotary control to adjust the sensitivity of the rain sensor. Set the control to low sensitivity, and the wipers will turn on when the rain sensor detects a large amount of moisture on the windshield. Set the control to high sensitivity, and the wipers will turn on when the rain sensor detects a small amount of moisture on the windshield.

71

Escape (TM2) , enUSA

E168041E168042Wipers and Washers

REAR WINDOW WIPER AND WASHERS Rear Window Wiper

Rear Window Washer

To use the rear washer function, push the lever away from you. When you release the lever, the wiper will operate for a short time.

Intermittent wipe Low-speed wipe Off

Press the top of the button at the end of the lever to switch on the intermittent wiper. Press the button again to switch on low-speed wipe. Press the bottom of the button to switch the wiper off, or to change the wiper speed from low-speed to intermittent. When you shift into R (Reverse), the rear wiper will turn on to intermittent if the front wipers are activated.

72

Escape (TM2) , enUSA

E168043E168044Lighting

LIGHTING CONTROL

Headlamp Flasher

Off Parking lamps, instrument panel lamps, license plate lamps and tail lamps Headlamps

High Beams

Pull the lever toward you slightly and release it to flash the headlamps.

AUTOLAMPS (If Equipped)

Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off.

The headlamps will switch on and off automatically in low light situations or during inclement weather. The headlamps will remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps will remain on. See Information Displays (page 89).

73

Escape (TM2) , enUSA

E142449E162679E162680E142451Lighting

When the headlamp switch is in the Autolamps position, the windshield wiper activated exterior lamps will turn on within 10 seconds when you switch the windshield wipers on. The exterior lamps will turn off approximately 60 seconds after you switch the windshield wipers off. This feature does not turn on the exterior lamps: • • while the wipers are on to clear washer

during a mist wipe

•

fluid during a wash condition if the wipers are in automatic or intermittent modes.

Note: If you have autolamps and autowipers switched on the low beam headlamps will turn on automatically when the windshield wipers operate continuously. Note: You may have to manually switch the headlamps on in severe weather conditions. Note: If you have autolamps switched on you can only switch the high beam headlamps on once the system has turned the headlamps on. INSTRUMENT LIGHTING DIMMER Note: You disable the manual dimmer when you adjust the setting to Auto Dimming in the information display. See Information Displays (page 89).

Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting.

Press repeatedly or press and hold until you reach the desired level. HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on.

74

Escape (TM2) , enUSA

E161902Lighting

FRONT FOG LAMPS

Press the control to switch the fog lamps on or off. You can switch the fog lamps on when the lighting control is in any position except Off and the high beams are not on. DIRECTION INDICATORS

DAYTIME RUNNING LAMPS (If Equipped)

WARNING

Always remember to switch your headlamps on in low light situations or during inclement weather. The

Daytime Running Lamp system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

To switch the Daytime Running Lamp system on: 1. Turn the ignition to the on position. 2. Switch the lighting control to the off, autolamp or parking lamp position.

Vehicles With Halogen Headlamps The Daytime Running Lamp system switches the low beam headlamps on at a reduced intensity in day light conditions. Vehicle With High Intensity Discharge Headlamps The Daytime Running Lamp system switches the fog lamps on in day light conditions (Not available in all markets).

Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. INTERIOR LAMPS The lamps will switch on when one of the following conditions have been met:

75

Escape (TM2) , enUSA

E142453E162681Lighting

With moonroof

• • •

You open any door. You press a remote control button. You press switch B on the front interior lamp.

Front Interior Lamp Without moonroof

(A) Door function switch. Press this switch to disable the interior lamps. The door function

indicator lamp will illuminate yellow with lamps disabled. Press the switch again to turn interior lamps back on. The indicator lamp will illuminate blue.

(B) All lamps on and off switch.

(C) Individual lamp on and off switch.

Rear Interior Lamp (If Equipped)

(A) You can switch individual map lamps on independently by pressing switch.

(A) Door function switch. Press this switch to disable the interior lamps. The door function

indicator lamp will illuminate yellow with lamps disabled. Press the switch again to turn interior lamps back on. The indicator lamp will illuminate blue.

(B) All lamps on and off switch.

(C) Passenger individual lamp on and off switch.

(D) Driver individual lamp on and off switch.

76

Escape (TM2) , enUSA

E161163DCABE160819E160816E160817E160818E142454BACE160819E160816E160818AE142455Lighting

AMBIENT LIGHTING (If Equipped) The ambient lighting system illuminates the interior with a choice of several colors. The ambient lighting control is located in the overhead console.

Color palette Control knob Search mode

Rotate B past the first detent to switch on and adjust to the desired brightness. Press A to cycle through the color choices. Press C to switch on all interior lamps and the ambient lighting. Press C again to switch off the interior lamps and return the ambient lighting to the previously selected color. The ambient lighting will switch on when the following conditions have been met: • • The ambient lighting will remain on until you switch the ignition off and one of the following conditions have been met: • •

you lock your vehicle the accessory delay timer expires.

you switch the ignition on you switch the headlamps on

77

Escape (TM2) , enUSA

E142456ABCWindows and Mirrors

Window Lock

Press the control to lock or unlock the rear window controls. It will illuminate when the rear window controls are locked. Bounce-Back (If Equipped) The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care

when closing the windows to avoid personal injury or damage to your vehicle.

Proceed as follows to override this protection feature when there is a resistance, for example in winter: 1. Close the window twice until it reaches

the point of resistance and let it reverse.

POWER WINDOWS WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

children and pets are not in the proximity of the window openings.

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. Press the switch to open the window. Lift the switch to close the window. One-Touch Down (If Equipped) Press the switch fully and release it. Press again or lift it to stop the window. One-Touch Up (If Equipped) Lift the switch fully and release it. Press or lift it again to stop the window.

78

Escape (TM2) , enUSA

E70848E70850Windows and Mirrors

EXTERIOR MIRRORS Power Exterior Mirrors WARNING

Do not adjust the mirrors when your vehicle is moving.

Left-hand mirror Off Right-hand mirror

Press the arrows to adjust the mirror. Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 108).

2. Close the window a third time to the point of resistance. The bounce-back feature is now disabled and you can close the window manually. The window will go past the point of resistance and you can close it fully.

See an authorized dealer as soon as possible if the window does not close after the third attempt. Resetting the Bounce-Back Feature

WARNING

The bounce-back feature remains turned off until you reset the memory.

If you have disconnected the battery, you must reset the bounce-back memory separately for each window. 1. Lift and hold the switch until the

window is fully closed.

2. Release the switch. 3. Lift the switch again for one more

second.

4. Press and hold the switch until the

window is fully open.

5. Release the switch. 6. Lift and hold the switch until the

window is fully closed.

7. Open the window and then try to close

it automatically.

8. Reset and repeat the procedure if the window does not close automatically.

Accessory Delay (If Equipped) You can use the window switches for several minutes after you have switched the ignition off or until either front door is opened.

79

Escape (TM2) , enUSA

ACBE70846E70847Windows and Mirrors

Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Memory Function (page 114). Integrated Blind Spot Mirrors (If Equipped)

WARNING

Objects in the blind spot mirror are closer than they appear.

Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to increase your visibility along the side of your vehicle. Check the main mirror first before a lane change, then check the blind spot mirror. If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.

Escape (TM2) , enUSA

The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C). Blind Spot Monitor (If Equipped) See Blind Spot Information System (page 161). INTERIOR MIRROR WARNING

Do not adjust the mirror when your vehicle is moving.

80

ABCE138665Windows and Mirrors

Illuminated Vanity Mirror (If Equipped)

Lift the cover to switch the lamp on. MOONROOF (If Equipped) WARNINGS

Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously

hurt themselves.

When closing the moonroof, you should verify that it is free of obstructions and make sure that

children and pets are not in the proximity of the roof opening.

The moonroof and sunscreen controls are located on the overhead console. The moonroof and sunscreen have a one-touch open and close feature. To stop them during one-touch operation, press the control a second time.

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up. SUN VISORS

Rotate the sun visor toward the side window and extend it rearward for extra shade.

81

Escape (TM2) , enUSA

E138666E162197Windows and Mirrors

Opening and Closing the Sunscreen

Press and release the rear of the control to open the sunscreen. Press and release the front of the control to close the sunscreen. If it is open, the moonroof will automatically close before the sunscreen closes. Opening and Closing the Moonroof

Press and hold the front of the control within two seconds of a bounce-back event to override this function. While bounce-back is active, the closing force increases for each of the next three times that you close the moonroof. Venting the Moonroof Press and release the front of the control to vent the moonroof. Press and release the rear of the control to close the moonroof. Note: When you vent the moonroof it will rise to 1.57 in (4 cm) and then lower slightly. This is normal. You cannot stop the moonroof in the higher position.

Press and release the rear of the control to open the moonroof. If it is closed, the sunscreen will automatically open before the moonroof opens. The moonroof will stop short of the fully opened position. Note: This position helps to reduce wind noise or rumbling which may happen with the moonroof fully open. Press and hold the control again to fully open the moonroof. Press and release the front of the control to close the moonroof. Bounce-Back The moonroof will stop automatically while closing. It will reverse some distance if there is an obstacle in the way.

82

Escape (TM2) , enUSA

E138668E138669Instrument Cluster

GAUGES

Information display Speedometer Engine coolant temperature gauge Fuel gauge Tachometer

Information Display Compass (If Equipped) Displays the vehicle’s heading direction. To calibrate and set the compass zone use the information display menu. See Information Displays (page 89). Use the diagram to determine your magnetic zone.

83

Escape (TM2) , enUSA

E171213Instrument Cluster

Fuel Gauge Note: The fuel gauge level may vary slightly when your vehicle is moving or when driving on a slope. Switch the ignition on. The fuel gauge will indicate approximately how much fuel is in the fuel tank. The arrow next to the fuel pump symbol shows the fuel filler door side of your vehicle. The needle will move toward full when you refuel your vehicle. If the needle still points to empty after adding fuel, have your vehicle repaired. After refueling the needle may not always return to exactly the same position. This is normal. Note: It may take a short time for the needle to reach full after refueling and driving. This is normal and may be due to the slope of pavement at the service station. Note: The fuel pumped into the tank may differ slightly from the fuel gauge. This is normal and may be due to the slope of pavement at the service station. Note: If the service station nozzle shuts off before the tank is full, complete refueling at a different pump. Low Fuel Level Reminder Vehicles with no distance-to-empty display A low fuel level reminder lights when the fuel gauge needle is at 1/16 above empty. Vehicles equipped with distance-to- empty display A low fuel level reminder displays when the fuel gauge needle is at 1/16 above empty or at about 35 miles (56km) to empty, whichever occurs first.

Odometer Located in the bottom of the information display, it registers the accumulated distance your vehicle has traveled. Outside Air Temperature Shows the outside air temperature. Trip Computer See Trip Computer (page 91). Vehicle Settings and Personalization See General Information (page 89). Engine Coolant Temperature Gauge

WARNING

Never remove the coolant reservoir cap while the engine is running or hot.

At normal operating temperature, the needle will remain in the center section. Note: Do not restart the engine until the cause of overheating has been resolved. If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down. See Engine Coolant Check (page 213).

84

Escape (TM2) , enUSA

123456789101112131415E142800Instrument Cluster

Variations: Note: The low fuel warning and distance-to-empty warning can appear at different fuel gauge positions depending on fuel economy conditions. This variation is normal.

Driving type (fuel economy

conditions)

Fuel gauge position

Distance-to-empty

Highway driving

1/16th

35 miles to 80 miles (56 km

to 129 km)

Severe duty driving (trailer

towing, extended idle)

1/16th-1/4

35 miles (16 km to 56 km)

WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information. Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle. Airbag - Front

If it fails to illuminate when you start your vehicle, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer.

Anti-Lock Braking System

If it illuminates when you are driving, this indicates a malfunction. You will continue

to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer. Battery

If it illuminates while driving, it indicates a malfunction. Switch off all unnecessary electrical

equipment and have the system checked by your authorized dealer immediately. Blind Spot Monitor (If Equipped)

It will illuminate when you switch this feature off or in conjunction with a message. See Blind Spot

Information System (page 161). See Information Messages (page 92). Brake System

It will illuminate when you engage the parking brake with the ignition on.

85

Escape (TM2) , enUSA

E124823E138644Instrument Cluster

Fasten Safety Belt

It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety

Belt Minder (page 31). Fog Lamps - Front (If Equipped)

It will illuminate when you switch the front fog lamps on.

High Beam

It will illuminate when you switch the high beam headlamps on. It will flash when you use the

headlamp flasher. Information (If Equipped)

It will illuminate when a new message is stored in the information display. It will be red or amber in color depending on the severity of the message and will remain on until the cause of the message has been rectified. See Information Messages (page 92). Low Fuel Level

It will illuminate when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as

possible. Low Tire Pressure Warning

It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check

your tire pressure as soon as possible.

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.

WARNING

Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Cruise Control (If Equipped)

It will illuminate when you switch this feature on. See Using Cruise Control (page 160).

Direction Indicator

Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the

indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 222). Engine Oil

If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 212). Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately.

86

Escape (TM2) , enUSA

E71340Instrument Cluster

It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer. Parking Lamps

It will illuminate when you switch the parking lamps on.

Service Engine Soon

If the service engine soon indicator light stays illuminated after the engine is started, it

indicates that the On-Board Diagnostics (OBD-II) system has detected a malfunction of the vehicle emissions control system. Refer to On-Board Diagnostics (OBD-II) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 135). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components. The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.

Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 135). Traction and Stability Control

It will flash when the system is active. If it remains illuminated or does not illuminate when you

switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. Traction and Stability Control Off It will illuminate when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off.

AUDIBLE WARNINGS AND INDICATORS Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position. Engine On Warning Chime A warning chime will sound when any door is opened if the vehicle exceeds a relatively low speed. Keyless Warning Alert (If Equipped) Sounds the horn twice when you exit the vehicle and the keyless vehicle is in RUN, indicating the vehicle is still on.

87

Escape (TM2) , enUSA

Instrument Cluster

Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately. Automatic Transmission Warning Chime Sounds when you have not moved the transmission selector lever to position P. A message will be shown in the display.

88

Escape (TM2) , enUSA

Information Displays

GENERAL INFORMATION

WARNING

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display. Information Display Controls

• Press the up and down arrow buttons

to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a

sub-menu.

• Press the left arrow button to exit a

menu.

• Press and hold the left arrow button at

any time to return to the main menu display (escape button).

• Press the OK button to choose and

confirm settings or messages. The OK button may also be used to reset some Trip values.

Menu Structure - Information Display All Vehicles You can access the menu using the information display control. Note: Some options may appear slightly different or not at all if the items are optional.

89

Escape (TM2) , enUSA

E138659Information Displays

Trip 1 and 21

Ford EcoMode

Anticipation

Speed

Ford EcoMode2

Distance to E Trip odometer Trip timer Instantaneous fuel Average fuel

Digital Speedo All Value - Distance to E, Trip odometer, Trip timer and Average fuel 1 See Trip Computer (page 91). 2 See Eco Mode (page 165).

Information

Intelligent 4WD MyKey Dist. MyKey Info

Driver Assist

Lighting

Display

Escape (TM2) , enUSA

Settings

Traction Ctrl Blind spot Cross traffic alert Rain Light Dimming Autolamp delay Navigation info Language

On or Off On or Off On or Off On or Off Auto or Manual Off or xx Seconds Always On or Always Off Choose your applicable setting

90

Information Displays

Settings

Chimes Convenience

Distance Temperature Park Slot Auto engine off Compass Remote Start

MyKey

Create MyKey Traction Ctrl Max Speed Speed Warning

Volume Limiter Clear MyKeys

Choose your applicable setting Choose your applicable setting On or Off On or Off Display Climate Control

On or Off Heater – A/C / Auto or Last Settings Front Defrost / Automatic or Off Rear Defrost / Automatic or Off (5, 10 or 15 minutes) On/Off

Enable or Disable

Duration Quiet Start Restore Default System Hold OK to Create MyKey Always On or User Selectable 80 MPH (130 km/h) or Off 45 mph (75 km/h), 55 mph (90 km/h), 65 mph (105 km/h) or Off On or Off Hold OK to Clear All MyKeys

System Check All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/down arrow buttons to scroll through the list.

TRIP COMPUTER Resetting the Trip Computer Press and hold OK on the current screen to reset the respective trip, distance, time and average fuel information.

91

Escape (TM2) , enUSA

Information Displays

Distance to E Indicates the approximate distance the vehicle will travel on the fuel remaining in the tank. Changes in driving pattern may cause the value to vary. Trip Odometer Registers the distance traveled of individual journeys. Trip Timer Registers the time of individual journeys. Instantaneous Fuel Shows your instantaneous fuel usage. Average Fuel Indicates the average fuel consumption since the function was last reset. Digital Speedo Shows a digital display of your vehicle speed. All Value Indicates all the respective remaining fuel, distance, time and average fuel information. INFORMATION MESSAGES Note: Depending on your vehicle options and instrument cluster type, not all of the messages will display or be available. Additionally, the information display may abbreviate or shorten certain messages.

92

Escape (TM2) , enUSA

Press the OK button to acknowledge and remove some messages from the information display. The information display will automatically remove other messages after a short time. You need to confirm certain messages before you can access the menus. Message indicator (If Equipped) The message indicator illuminates to supplement some messages. It will be red or amber depending on the severity of the message and will remain on until you or your authorized dealer have fixed the vehicle concern. A system specific symbol with a message indicator may supplement some messages.

E130248Information Displays

Airbag

Message

Airbag fault Service now

Alarm

Message

Alarm activated Check

Vehicle

Message Indicator Amber

Message Indicator Amber

Alarm fault Service

required

Automatic Engine Shutdown Message Indicator

Message

Engine Shuts Off For

Fuel Economy

Engine Shuts Off in XX Seconds OK to Override

Action

Displays when the system requires service due

to a malfunction. Contact your authorized

dealer.

Action

Displays when the alarm has been triggered due to unauthorized entry. See Anti-Theft

Alarm (page 65).

Displays when the system requires service due

to a malfunction. Contact your authorized

dealer.

Action

Displays when the engine has shut off to help

increase fuel economy.

Displays when the engine is getting ready to shut off. You can press OK on the left steering

wheel button to override the shut down.

93

Escape (TM2) , enUSA

Information Displays

Battery and Charging System Message Indicator

Message

Electrical system over-

voltage Stop safely

Red

Battery low See manual

Amber

Action

Stop your vehicle as soon as it is safe to do so

and switch off the ignition. Contact your

authorized dealer.

Displays to warn of a low battery condition. Turn off all unneeded electrical accessories.

Contact your authorized dealer.

Blind Spot Information and Cross Traffic Alert System Action

Message

BLIS Low visibility See

manual

BLIS: X sensor fault

Service required

BLIS not available Trailer

attached

Cross Traffic Vehicle

coming from X

Cross Traffic Sensor blocked See manual

Cross Traffic fault Service required

Message Indicator Amber

Amber

Amber

Amber

Amber

Amber

Displayed when the blind spot information system and cross traffic alert system sensors are blocked. See Blind Spot Information

System (page 161).

Displayed when a fault with the system has occurred. Contact your authorized dealer as

soon as possible.

Displayed when the system is not available due to trailer use. See Blind Spot Information

System (page 161).

Displayed when the system detects a vehicle. See Blind Spot Information System (page

161).

Displayed when the blind spot information system and cross traffic alert system sensors are blocked. See Blind Spot Information

System (page 161).

Displays when the system requires service due

to a malfunction. Contact your authorized

dealer.

Cross Traffic disabled

Trailer attached

Displayed when the system is not available due to trailer use. See Blind Spot Information

System (page 161).

94

Escape (TM2) , enUSA

Doors

Message

X door open

Liftgate ajar

Hood open

Information Displays

Message Indicator

Action

Red

Red

Red

Displays when the door(s) listed is not

completely closed and the vehicle is moving.

Displays when the door(s) listed is not

completely closed.

Displays when the luggage compartment is not completely closed and the vehicle is moving. Displays when the luggage compartment is not

completely closed.

Displays when the hood is not completely

closed and the vehicle is moving.

Displays when the hood is not completely

closed.

Engine

Message

Engine fault Service now

Message Indicator Amber

High engine temperature

Stop safely

Red

Power reduced to lower

temperature

Action

Engine service is required. Contact your

authorized dealer.

Displays when the engine temperature is too high. Stop the vehicle in a safe place and allow to engine to cool. If the problem persists, contact your authorized dealer. See Engine

Coolant Check (page 213).

Displays when the engine has reduced power in order to help reduce high coolant temper-

ature.

95

Escape (TM2) , enUSA

Information Displays

Hill Start Assist

Message

Hill start assist not avail-

able

Keyless Vehicle Message

Ford KeyFree Key inside

vehicle

Ford KeyFree No key

detected

Switch ign. off Press ENGINE Start/Stop

button

Press brake to start

Ford KeyFree Key not

inside car

Key Battery low Replace

soon

Message Indicator Amber

Message Indicator Amber

Red

Red

Action

Displays when hill start assist is not available. Contact your authorized dealer. See Hill Start

Assist (page 147).

Action

Displays to remind you that the key is in the trunk. See Keyless Starting (page 124). Displayed if the key is not detected by the system. See Keyless Starting (page 124). Displayed as a reminder to turn off the vehicle.

See Keyless Starting (page 124).

Displayed as a reminder to press the brake

while starting the vehicle.

Displayed when a valid key is not detected

within the vehicle. See Keyless Starting (page

124).

Displays when the key battery is low. Change the battery as soon as possible. See Remote

Control (page 43).

96

Escape (TM2) , enUSA

Information Displays

Lighting

Message

Message Indicator

Brake lamp Bulb fault

Low beam Bulb fault

Headlamp fault Service

required

Amber

Action

Displays when the brake lamp bulb has burned

out. Contact your authorized dealer.

Displays when the low beam headlamp bulb has burned out. Contact your authorized dealer. Displays when an electrical system problem occurs with the headlamp system. Contact your

authorized dealer.

Maintenance Message

Message Indicator

Action

Engine oil change due

Displays when the engine oil life is depleted and

requires a change. See Engine Oil Check

(page 212).

Brake fluid level low

Service now

Check fuel fill inlet

Red

Indicates the brake fluid level is low and the brake system should be inspected immediately.

See Brake Fluid Check (page 216).

Displays when the fuel fill inlet was not properly

closed. See Refueling (page 133).

MyKey

Message

MyKey active Drive

Safely

MyKey Speed Limited to

XX MPH/km/h

MyKey Vehicle Near Top

Speed

Message Indicator

Amber

Action

Displays when MyKey is active.

Displays when starting the vehicle and MyKey

is in use and the MyKey speed limit is on.

Displays when a MyKey is in use and the MyKey

speed limit is on and the vehicle speed is

approaching 80 mph (130 km/h).

97

Escape (TM2) , enUSA

Information Displays

Message Indicator Amber

Action

Displays when a MyKey is in use and the MyKey

speed limit is reached.

Displays when MyKey is active.

Displays when a MyKey is in use and Belt-

Minder is activated.

Displays when a MyKey is in use and park aid is

activated.

Displays when trying to create a MyKey with a

key already designated as a MyKey. Displays when programming a MyKey.

Displays when programming a MyKey.

Message

MyKey Vehicle at Top

Speed

MyKey Check Speed

Drive Safely

MyKey Buckle Up to

Unmute Audio

MyKey Park aid cannot

be deactivated

Key is Already a MyKey

Hold key next to symbol

on steering column MyKey ESC cannot be

deactivated

Park Aid

Message

Parking aid malfunction

Service required

Park Brake

Message

Park brake applied

Message Indicator Amber

Message Indicator

Red

Action

Displays when the system has detected a condition that requires service. Contact your authorized dealer. See Parking Aid (page 151).

Action

Displays when the parking brake is set, the

engine is running and the vehicle is driven more than 3 mph (5 km/h). If the warning stays on after the parking brake is released, contact your

authorized dealer.

98

Escape (TM2) , enUSA

Information Displays

Power Steering Message

Message Indicator

Action

Steering loss Stop safely

Red

Steering assist fault

Service required

Steering fault Service

now

Amber

Amber

The power steering system is not working. Stop the vehicle a safe place. Contact your author-

ized dealer.

The power steering system is not working. Stop the vehicle a safe place. Contact your author-

ized dealer.

The power steering system has detected a

condition within the power steering system or passive entry or passive start system requires

service. Contact your authorized dealer.

Starting System

Message

Message Indicator

Action

Press brake to start

Cranking time exceeded

Displays when starting the vehicle as a reminder

to apply the brake.

Displays when the vehicle fails to start.

Transmission and Four-Wheel Drive

Message

Transmission fault

Service now

Transmission overtem- perature Stop safely

Transmission Service

required

Transmission Hot Stop

or Speed Up

Message Indicator

Amber

Amber

Action

See your authorized dealer.

The transmission is overheating and needs to

cool. Stop in a safe place as soon as it’s

possible.

See your authorized dealer.

Transmission is getting hot. Stop to let it cool

or speed up.

99

Escape (TM2) , enUSA

Information Displays

Message

Transmission Hot Wait

...

4WD fault Service

required

Message Indicator

Amber

4WD Off

Amber

4WD temporarily

disabled

Amber

4WD restored

Transmission not in Park

Select P

Press brake to unlock

gearshift lever

Gearshift lever unlocked

Action

Transmission is hot. Wait as needed to let it

cool.

The system is not functioning correctly and defaulted to front-wheel drive. See your authorized dealer. See Using Four-Wheel

Drive (page 141).

Displays when the system disables automatic- ally and enters front-wheel drive only mode to protect driveline components. See Using Four-

Wheel Drive (page 141).

The system has overheated and defaulted to front-wheel drive. See Using Four-Wheel

Drive (page 141).

Displays when system operation has been

restored. See Using Four-Wheel Drive (page

141).

Displays as a reminder to shift into park.

Displays to request the operator to apply the

brake as needed by the transmission.

Displays when the transmission shift lever is

unlocked and free to select gears.

100

Escape (TM2) , enUSA

Information Displays

Tire Pressure Monitoring System

Message

Low Tire Pressure

Message Indicator Amber

Tire Pressure Monitor

Fault

Amber

Tire Pressure Sensor

Fault

Amber

Action

Displays when one or more tires on your vehicle

have low tire pressure. See Tire Pressure

Monitoring System (page 253).

Displays when the tire pressure monitoring system is malfunctioning. If the warning stays authorized dealer. See Tire Pressure Monit-

on or continues to come on, contact your

oring System (page 253).

Displayed when a tire pressure sensor is

malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, see See Tire Pressure Monitoring System (page 253). If the warning stays on or continues to come on, contact your

authorized dealer as soon as possible.

Traction Control

Message

Message Indicator

Action

Traction control off

Displays when the traction control system has

been switched off. See Using Traction

Control (page 148).

101

Escape (TM2) , enUSA

Climate Control

MANUAL CLIMATE CONTROL

Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed. Recirculated air: Press the button to switch between outside air and recirculated air. When recirculated air is selected, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may also reduce unwanted odors from entering your vehicle. Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. Temperature control: Controls the temperature of the airflow in your vehicle. Adjust to select the desired temperature. MAX A/C: Turn the temperature control dial all the way past the full cool position to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on and the fan automatically adjusts to the highest speed. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Air distribution control: Turn the dial switch airflow from the windshield, instrument panel, or footwell vents on or off. The system can distribute air through any combination of these vents.

102

Escape (TM2) , enUSA

E141421AEBDCClimate Control

AUTOMATIC CLIMATE CONTROL

AUTO and Driver temperature control: Press the button to turn on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature. You can also use the AUTO button to turn off dual zone operation by pressing and holding the button for more than two seconds. Turn the control to increase or decrease the air temperature for the driver side of the vehicle. This control also adjusts the passenger side temperature when not in dual zone mode. Fan speed: Press the large fan icon or small fan icon to increase or decrease the volume of air circulated in the vehicle. Pressing one of the fan speed buttons while in AUTO takes the system out of AUTO fan mode. Power: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle. MAX Defrost: Press the button to maximize defrosting. Outside air flows through the windshield vents, fan automatically adjusts to the highest speed and the temperature dial returns to the full heat position. You can use this setting to defog or clear a thin covering of ice from the windshield. The heated