2013 Ford Escape Owners Manual

F8
F9
F10
F11
F12
F13
F14

F15
F16

F17
F18
F19

F20
F21
F22
F23
F24
F25

F26
F27
F28
F29

40A**

30A**

40A**

30A** 30A** 25A**

20A** 25A**

20A** 20A** 5A*

15A* 5A* 15A* 5A* 5A* 10A*

5A* 15A* 10A* 25A*

Anti-lock brake system and electronic stability program pump Electronic stability program valve Not used Heater blower motor Not used Powertrain control module relay fuse Starter relay Rear power window (without door control unit) Front cigar lighter or power outlet Front power window (without door control unit) Rear power outlet Center power outlet Anti-lock brake system and electronic stability program 15 feed Horn Stop light switch Battery monitor system Relay coils Light switch module Power exterior mirror (without door control unit) Keep-alive power Air conditioner clutch Vehicle power - fuel injector Rear window defroster

211

Escape (TM2)

Fuses

Fuse or relay number

Fuse amp rating

Protected components

F30
F31

F32
F33
F34
F35
F36
F37

F38

F39

F40
F41
F42
F43
F44
F45
F46
F47
F48
R1
R2
R3

R4
R5

5A*

15A* 10A* 10A* 15A* 5A* 10A*

5A*

5A*

5A* 20A* 15A* 15A* 15A*

50A**

5A*

Micro relay

Not used Power transfer unit oil cooling fan (Middle East specification) Vehicle power Vehicle power 2
Vehicle power 3
Vehicle power 4
Active grill shutters Occupant classification sensor, Passenger airbag deactivation indicator feed Engine control module and transmission control module ignition feed Daytime running lamps and headlamp control module ignition feed Electronic power assist steering 15 feed Body control module 15 feed Rear wiper Headlamp control module supply Front fog daytime running lamps Not used Smart wiper motor modules Not used Keypad Not used Horn Power transfer unit oil cooling fan (Middle East specification) Front fog daytime running lamps Not used

212

Escape (TM2)

Fuses

Fuse or relay number

Fuse amp rating

Protected components

R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16

Mini relay

Mini relay Micro relay Power relay Mini relay Mini relay Power relay Power relay

Not used Not used Delayed accessory relay Not used Starter relay Air conditioner clutch Cooling fan Heater blower Engine control relay Heated rear window Ignition 15

*Mini fuses **Cartridge fuses

Passenger Compartment Fuse Panel The fuse panel is located on the right side below the glove box.

213

Escape (TM2)

Fuses

The fuses are coded as follows:

214

Escape (TM2)

Fuses

Fuse or relay number

Fuse amp rating

Protected components

56
57
58
59
60

61
62
63
64
65
66
67

68
69
70
71

72
73
74
75
76
77
78

20A

5A 10A

20A 5A 10A 20A 7.5A

5A 20A 10A

7.5A 5A 15A 15A 10A 20A 5A

Fuel pump supply, Air mass meter Not used Not used Passive anti-theft transceiver Interior light, Driver door switch pack, Glove box illumination, Overhead console switch bank Cigar lighter, Power point Rain sensor module, Auto-dimming mirror Not used Not used Liftgate release Driver door unlock supply, Double lock SYNC, Multifunction display, Global posi- tioning system module Not used Instrument cluster Central lock and unlock supply Heating control head (manual air condi- tioner), Dual electronic automatic temperature control Steering wheel module Data link connector High beam headlamp supply Fog lamp supply Reversing lamp supply Windshield washer supply Ignition switch, Start button

215

Escape (TM2)

Fuses

Fuse or relay number

Fuse amp rating

Protected components

79

80
81
82
83
84
85
86

87
88
89

15A

20A 5A 20A 20A 20A 7.5A 10A

Radio, Navigation DVD player, Touch screen, Hazard light switch, Door lock switch Moonroof supply Radio frequency receiver Windshield washer relay Central locking Drive door unlock supply, Double lock Electronic 15 feed Air bag module, Occupant classification system, Passenger air bag deactivation indicator Not used Not used Not used

Luggage Compartment Fuse Panel The fuse panel is located in the luggage compartment behind the passenger's side wheel well. Remove the fuse panel cover to gain access to the fuses.

(cid:40)(cid:20)(cid:21)(cid:28)(cid:28)(cid:21)(cid:26)

The fuses are coded as follows:

216

Escape (TM2)

Fuses

Fuse or relay number

Fuse amp rating

F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26

5A 10A 5A 25A 25A 25A 25A

25A 5A 5A

25A 30A 25A 40A

Protected components Hands-free liftgate entry module Keyless vehicle module Keyless vehicle door handles Door control unit front left Door control unit front right Door control unit rear left Door control unit rear right Not used Driver seat motor Driver seat memory module logic feed Rear ignition coil feed Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Audio amplifier DC/AC power converter Power liftgate Accessories / Trailer tow module 30 feed

217

Escape (TM2)

Fuses

Fuse or relay number

Fuse amp rating

Protected components

F27
F28
F29

F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
R1
R2
R3
R4
R5
R6

5A

5A 5A

20A 20A

5A

Power relay

Not used Not used Blind spot detection system, Rear view camera with park assist Parking aid module Not used DC/AC power converter Not used Driver seat heater Passenger seat heater Not used Moonroof Not used Not used Not used Not used Not used Not used Not used Not used Not used Rear 15 relay Not used Not used Not used Not used Not used

218

Escape (TM2)

Maintenance

Working with the Engine Off 1. Set the parking brake and shift to P

(Park).

2. Turn off the engine and remove the key

(if equipped).

3. Block the wheels. Working with the Engine On

WARNING

To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

1. Set the parking brake and shift to P

(Park).

2. Block the wheels OPENING AND CLOSING THE HOOD Opening the Hood

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialized tools developed specifically for servicing your vehicle. To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. See Scheduled Maintenance (page ?). If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your warranty information to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft® parts are designed and built to provide the best performance in your vehicle. Precautions • Do not work on a hot engine. • Make sure that nothing gets caught in

moving parts.

• Do not work on a vehicle with the

engine running in an enclosed space, unless you are sure you have enough ventilation. Keep all open flames and other burning material (such as cigarettes) away from the battery and all fuel related parts.

•

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:24)(cid:26) 1. Pull the hood release handle.

219

Escape (TM2)

Maintenance

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:24)(cid:27) 2. Move the catch to the right.

(cid:40)(cid:27)(cid:26)(cid:26)(cid:27)(cid:25) 3. Open the hood and support it with the

prop rod.

Closing the Hood 1. Remove the prop rod from the catch

and secure properly after use.

2. Lower the hood and allow it to drop

from under its own weight for the last 8 - 11 inches (20 – 30 centimeters).

Note: Make sure that you have closed the hood properly.

220

Escape (TM2)

Maintenance

UNDER HOOD OVERVIEW - 1.6L ECOBOOST™

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:24)(cid:28)

Engine coolant reservoir Engine oil filler cap Brake fluid reservoir Battery Power distribution box Air filter assembly Engine oil dipstick Windshield washer fluid reservoir

221

Escape (TM2)

Maintenance

UNDER HOOD OVERVIEW - 2.0L ECOBOOST™

(cid:40)(cid:20)(cid:23)(cid:25)(cid:19)(cid:21)(cid:21)

Engine coolant reservoir Engine oil dipstick Brake fluid reservoir Battery Power distribution box Air filter assembly Engine oil filler cap Windshield washer fluid reservoir

222

Escape (TM2)

Maintenance

UNDER HOOD OVERVIEW - 2.5L

(cid:36)

(cid:38)(cid:37)

(cid:39)

(cid:40)

(cid:41)

(cid:42)

(cid:43)

(cid:40)(cid:20)(cid:23)(cid:25)(cid:19)(cid:21)(cid:22)

Windshield washer fluid reservoir Engine coolant reservoir Engine oil filler cap Engine oil dipstick Brake fluid reservoir Battery Power distribution box Air filter assembly

223

Escape (TM2)

Maintenance

ENGINE OIL DIPSTICK - 1.6L ECOBOOST™

(cid:40)(cid:20)(cid:23)(cid:25)(cid:19)(cid:21)(cid:19)

MIN MAX

ENGINE OIL DIPSTICK - 2.0L ECOBOOST™/2.5L

Note: Make sure that the level is between the MIN and the MAX marks. 1. Make sure that your vehicle is on level

ground.

2. Turn the engine off and wait 10 minutes

for the oil to drain into the oil pan.

3. Remove the dipstick and wipe it with

a clean, lint-free cloth. Replace the dipstick and remove it again to check the oil level.

If the level is at the MIN mark, add oil immediately. Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:26)(cid:22)(cid:21) Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:21)

MIN MAX

ENGINE OIL CHECK Note: Check the level before starting the engine.

224

Escape (TM2)

Maintenance

Note: Make sure that the level is between the MIN and MAX marks on the coolant reservoir. Note: Coolant expands when it is hot. The level may extend beyond the MAX mark Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately. See Adding Engine Coolant in this chapter. The coolant concentration should be maintained within 48% to 50%, which equates to a freeze point between -30 F degrees (-34 C) and -34 F (-37 C). Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from your authorized dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable. Do not use engine coolant or antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding Engine Coolant WARNINGS

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.

Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine

coolant could make it difficult to see through the windshield.

1. Remove the filler cap. 2. Add engine oil that meets the Ford specifications. See Capacities and Specifications (page ?).

3. Replace the filler cap. Turn it until you

feel a strong resistance.

Resetting the Oil Life Monitoring System Note: Reset the oil life monitoring only after an oil change. 1. Turn the ignition key to the on position.

Do not start the engine. For vehicles with push-button start, press and hold the start button for two seconds without pressing the brake pedal. Do not attempt to start the engine.

2. Press both the accelerator and brake

pedals at the same time.

3. Keep both pedals fully pressed. 4. After three seconds, the Service: Oil

reset in prog. message will be displayed.

5. After 25 seconds, the Service: Oil reset complete message will be displayed. 6. Release both the accelerator and brake

pedals.

7. The Service: Oil reset complete

message will no longer be displayed. 8. Rotate the key to the off position. For vehicles with push-button start, press the start button to turn the vehicle off completely.

ENGINE COOLANT CHECK Checking the Engine Coolant When the engine is cold, check the concentration and level of the engine coolant at the intervals listed in the scheduled maintenance information. See Scheduled Maintenance (page 400).

225

Escape (TM2)

Maintenance

WARNINGS

To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.

Do not add coolant further than the MAX mark.

Note: Do not use stop leak pellets, cooling system sealants, or additives as they can cause damage to the engine cooling or heating systems. This damage would not be covered under your vehicle’s warranty. Note: During normal vehicle operation, the engine coolant may change color from orange to pink or light red. As long as the engine coolant is clear and uncontaminated, this color change does not indicate the engine coolant has degraded nor does it require the engine coolant to be drained, the system to be flushed, or the engine coolant to be replaced.

• Do not mix different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty. Use prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page ?). In case of emergency, a large amount of water without engine coolant may be added in order to reach a vehicle service location. In this instance, the cooling system must be drained, chemically cleaned with Motorcraft® Premium Cooling System Flush, and refilled with prediluted engine coolant as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing.

•

• Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant.

Unscrew the cap slowly. Any pressure will escape as you unscrew the cap. Add prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page ?). Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough prediluted engine coolant to bring the coolant level to the proper level.

226

Escape (TM2)

Maintenance

Recycled Engine Coolant Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%.

• A coolant concentration of 60% will

provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage

If you drive in extremely hot climates: It may be necessary to have a Ford • authorized dealer decrease the coolant concentration to 40%.

• A coolant concentration of 40% will

provide improved overheat protection. Engine coolant concentrations below 40% will decrease the corrosion/freeze protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.

What you Should Know About Fail- Safe Cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How Fail-Safe Cooling Works If the engine begins to overheat, the engine coolant temperature gauge will move to the red (hot) area and:

A high engine temperature message will appear in the information display. The service engine soon indicator will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • •

The engine power will be limited. The air conditioning system will be disabled.

Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage.

227

Escape (TM2)

Maintenance

AUTOMATIC TRANSMISSION FLUID CHECK Note: Transmission fluid should be checked by an authorized dealer. If required, fluid should be added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. Have an authorized dealer check and change the transmission fluid and filter at the correct service interval. See Scheduled Maintenance (page 400). Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e., if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately. POWER STEERING FLUID CHECK Your vehicle is equipped with an electric power steering (EPS) system. There is no fluid reservoir to check or fill.

When Fail-Safe Mode Is Activated

WARNINGS

Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist, and power brake assist, which may increase the possibility of a crash resulting in serious injury.

Never remove the coolant reservoir cap while the engine is running or hot.

You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine.

2. Arrange for the vehicle to be taken to

3.

an authorized dealer. If this is not possible, wait a short period for the engine to cool.

4. Check the coolant level and replenish

if low.

5. Re-start the engine and take your

vehicle to an authorized dealer.

Note: Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible.

228

Escape (TM2)

Maintenance

CHANGING THE 12V BATTERY

WARNINGS

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow

flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or

clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

Your vehicle is equipped with a Motorcraft® maintenance-free battery which normally does not require additional water during its life of service. Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. Note: See an authorized dealer for low voltage battery access, testing, or replacement.

FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. WASHER FLUID CHECK

WARNING

If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze

protection. Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Note: The front and rear washer systems are supplied from the same reservoir. Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See Capacities and Specifications (page 273). State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.

229

Escape (TM2)

Maintenance

presets, are also maintained in memory by power from the low voltage battery. When a technician disconnects and connects the low voltage battery, these settings are erased. Complete the following procedure in order to restore the settings: 1. With the vehicle at a complete stop,

set the parking brake.

2. Shift the transmission into P. 3. Turn off all accessories. 4. Step on the brake pedal and start the

vehicle.

5. Run the engine until it reaches normal

operating temperature. While the engine is warming up, complete the following: Reset the clock. See Audio System (page 98). Reset the power windows bounce-back feature. See Windows and Mirrors (page ?). Reset the radio station presets. See Audio System (page 98).

6. Allow the engine to idle for at least one minute. If the engine turns off, step on the accelerator to start the engine.

7. While the engine is running, step on the brake pedal and shift the transmission to N.

8. Allow the engine to run for at least one minute by pressing on the accelerator pedal.

9. Drive the vehicle at least 10 miles (16
kilometers) to completely relearn the idle and fuel trim strategy.

Note: If you do not allow the engine to relearn the idle and fuel trim strategy, the idle quality of your vehicle may be adversely affected until the engine computer eventually relearns the idle trim and fuel trim strategy.

When a low voltage battery replacement is necessary, see an authorized dealer to replace the low voltage battery with a Ford recommended replacement low voltage battery that matches the electrical requirements of the vehicle To ensure proper operation of the battery management system (BMS), do not allow a technician to connect any electrical device ground connection directly to the low voltage battery negative post. A connection at the low voltage battery negative post can cause inaccurate measurements of the battery condition and potential incorrect system operation. Note: Note: If a person adds electrical or electronic accessories or components to the vehicle, the accessories or components may adversely affect the low voltage battery performance and durability and may also affect the performance of other electrical systems in the vehicle. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. When a battery replacement is required, the battery should only be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle. Because your vehicle’s engine is electronically-controlled by a computer, some engine control settings are maintained by power from the low voltage battery. Some engine computer settings, like the idle trim and fuel trim strategy, optimize the driveability and performance of the engine. Some other computer settings, like the clock and radio station

230

Escape (TM2)

Maintenance

Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. Note: It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. CHECKING THE WIPER BLADES

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:22) Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES The wiper arms can be manually moved when the ignition is off. This allows for ease of blade replacement and cleaning under the blades. 1. Pull the wiper blade and arm away

from the glass.

Escape (TM2)

(cid:20)

(cid:20)

(cid:21)

Install in the reverse order.

(cid:40)(cid:20)(cid:21)(cid:28)(cid:28)(cid:28)(cid:19) 2. Press the locking buttons together. 3. Rotate and remove the wiper blade. 4. Note: Make sure that the wiper blade locks into place. Lower the wiper arm and blade back to the windshield. The wiper arms will automatically return to their normal position when the ignition is turned on. To change the rear blades, do the following: 1. Lift the wiper arm.

(cid:22)

(cid:21)

(cid:40)(cid:20)(cid:22)(cid:19)(cid:19)(cid:25)(cid:19) 2. Slightly rotate the wiper blade from the

wiper arm.

3. Disengage the wiper blade from the

wiper arm.

4. Remove the wiper blade.

231

Maintenance

Install in the reverse order.

5. Note: Make sure that the wiper blade locks into place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. CHANGING THE ENGINE AIR FILTER

WARNING

To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

When changing the air filter element, use only the air filter element listed. See Capacities and Specifications (page 273). For EcoBoost equipped vehicles: When servicing the air cleaner, it is important that no foreign material enter the air induction system. The engine and turbocharger are susceptible to damage from even small particles. Change the air filter element at the proper interval. See Scheduled Maintenance (page 400). Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.

1.6L and 2.0L EcoBoost Engines

(cid:40)(cid:20)(cid:23)(cid:21)(cid:26)(cid:20)(cid:19)

2.5L Engine

(cid:40)(cid:20)(cid:23)(cid:21)(cid:26)(cid:20)(cid:20) 1. Loosen the screws on the air tube clamp that fasten it to the air filter assembly tray.

2. Separate the clean air tube from the

air cleaner.

3. Remove the air cleaner from the

vehicle.

4. 5. Carefully separate the two halves of

the air filter housing. •

For 2.5L engines, disengage the clips that secure the air filter housing cover. For 1.6L and 2.0L engines, remove the screws securing the air filter housing cover.

•

6. Remove the air filter element from the

air filter housing.

232

Escape (TM2)

Maintenance

25 feet (7.6 meters) Horizontal reference line

Vehicles With Halogen Headlamps 1. Park the vehicle directly in front of a

wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

2. Measure the height of the headlamp

bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height.

Note: To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 3. Turn on the low beam headlamps to

illuminate the wall or screen and open the hood.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:24) 4. On the wall or screen you will observe

a flat zone of high intensity light located at the top of the right hand portion of the beam pattern. If the top edge of the high intensity light zone is not at the horizontal reference line, the headlamp will need to be adjusted.

7. Wipe any dirt or debris from the air filter housing and cover to make sure no dirt gets in the engine and to make sure you have a good seal.

8. Slide the open end of the air filter

element in first, below the tab. Then push the closed end cap into the bottom of the tray. The closed end cap should fit inside the groove in the tray. The tab at the end of the closed end cap should be oriented down and fit between the forks on the tray.

9. Replace the air filter housing cover and

secure the clips.

10. Reinstall the air cleaner assembly into

the vehicle.

11. Reinstall the clean air tube assembly

into the air cleaner assembly.

12. Tighten the air tube fastening screws. ADJUSTING THE HEADLAMPS Vertical Aim Adjustment The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:24)(cid:28)(cid:21)

8 feet (2.4 meters) Center height of lamp to ground

233

Escape (TM2)

Maintenance

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:26) 5. Locate the vertical adjuster on each

headlamp. Using a Phillips #2
screwdriver, turn the adjuster either clockwise or counterclockwise in order to aim the headlamp. The horizontal edge of the brighter light should touch the horizontal reference line.

6. Close the hood and turn off the lamps. Vehicles With High Intensity Discharge Headlamps 1. Park the vehicle directly in front of a

wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

2. Measure the height of the headlamp

bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height.

Note: To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 3. Turn on the low beam headlamps to

illuminate the wall or screen and open the hood.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:25) 4. There is a distinct cut-off (change from light to dark) in the left portion of the beam pattern. The top edge of this cut-off should be positioned two inches (5 centimeters) below the horizontal reference line.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:26) 5. Locate the vertical adjuster on each

headlamp. Using a Phillips #2
screwdriver, turn the adjuster either clockwise or counterclockwise in order to aim the headlamp.

6. Close the hood and turn off the lamps. Horizontal Aim Adjustment Horizontal aim is not required for this vehicle and is non-adjustable.

234

Escape (TM2)

Maintenance

Examples of acceptable condensation are: • Presence of thin mist (no streaks, drip

marks or droplets). Fine mist covers less than 50% of the lens.

Examples of unacceptable moisture (usually caused by a lamp water leak) are: • Water puddle inside the lamp. •

Large water droplets, drip marks or streaks present on the interior of the lens.

Take your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present. Replacing Headlamp Bulbs

WARNING

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb by only its

plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

REMOVING A HEADLAMP

•

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:27) 1. Make sure the headlamp control is in the off position and open the hood.

2. Remove the two screws from the

headlamp assembly.

3. Carefully pull the headlamp assembly as far as possible towards the front of the vehicle to disengage it from the lower fixing point.

4. Carefully lift the outer side of the

headlamp and remove it.

5. Disconnect the electrical connector. CHANGING A BULB Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions.

235

Escape (TM2)

Maintenance

Headlamp:

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:26)(cid:20) 1. Remove the headlamp. 2. Remove service cap. 3. Disconnect the electrical connector. 4. Remove bulb from the headlamp

assembly by turning it counterclockwise, then pull it straight out.

Install the new bulbs in reverse order from the steps above. Be sure that the spring clip is not damaged or detached from the headlamp assembly during the replacement procedure. Replacing HID Headlamp Bulbs (If Equipped) The low beam headlamps on your vehicle use a high intensity discharge source. These lamps operate at a high voltage. When the bulb is burned out, the bulb and starter capsule assembly must be replaced by your authorized dealer.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:25)(cid:28)

Side marker Low beam headlamp High beam headlamp

High beam headlamp:

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:26)(cid:19) 1. Remove the headlamp. 2. Remove service cap. 3. Disconnect the electrical connector. 4. Remove bulb from the headlamp

assembly by turning it counterclockwise, then pull it straight out.

Low beam headlamp:

236

Escape (TM2)

Maintenance

Replacing Side Marker Bulbs

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:26)(cid:21) 1. Remove the bulb socket from the headlamp assembly by turning it counterclockwise.

2. Remove the bulb by gently pull the

bulb straight out of the socket.

Install the new bulb in reverse order. Replacing Fog, Park and Turn Signal Bulbs

(cid:40)(cid:20)(cid:23)(cid:21)(cid:26)(cid:28)(cid:26)

Fog Lamp Park Lamp Turn Signal lamp

(cid:40)(cid:20)(cid:23)(cid:21)(cid:26)(cid:28)(cid:27) 1. Remove the screws from the splash

shield at the wheel well to gain access to the lamp assembly.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:26)(cid:28)(cid:28) 2. Remove the bulb holder from the lamp

assembly by turning it counterclockwise.

3. Disconnect the electrical connector. 4. Remove the bulb from the bulb holder

by pulling it straight out.

Install the new bulbs in reverse order from the steps above.

237

Escape (TM2)

Maintenance

Replacing Tail, Brake and Turn Signal Bulbs

6. Remove the turn signal bulb or the tail

and brake bulb by turning the bulb socket counterclockwise. Gently pull the bulb straight out of the socket.

Install the new bulb in reverse order. Replacing Reverse Lamp Assembly For bulb replacement, see your authorized dealer. Replacing License Plate Lamp Bulb

(cid:22)

(cid:21)

(cid:20)

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:26)(cid:22) 1. Make sure the headlamp control is in the off position and open the liftgate.

2. Remove the two bolt covers using a

standard flat tip screwdriver.

3. Remove the two bolts from the lamp

assembly.

4. Gently pull the lamp assembly away

from the vehicle.

(cid:40)(cid:26)(cid:21)(cid:26)(cid:27)(cid:28) 1. Carefully release the spring clip. 2. Remove the lamp. 3. Remove the bulb. Reverse steps to reinstall bulb. Replacing High-Mount Brake Lamp Bulb Your vehicle is equipped with an LED center high-mount stop lamp located in the spoiler. It is designed to last the life of the vehicle. If replacement is required, see your authorized dealer.

(cid:40)(cid:20)(cid:23)(cid:21)(cid:23)(cid:26)(cid:24) 5. Disconnect the electrical connector.

238

Escape (TM2)

Maintenance

BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for

North America to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

Function

Trade number

9005LL

H1

H11LL D3S 168

WY5W

194

WY21W W21W

Headlamps high beam (Halogen) * Headlamps high beam (HID) Headlamp low beam (Halogen) * Headlamp low beam (HID) Sidemarker - front Park lamp - front (HI Series) Park lamp - front (Low Series) Turn lamp - front (HI Series) Turn lamp - front (Low Series) Fog lamps Tail/brake lamp Turn lamp - rear Backup lamp License plate lamp * High-mount brake lamp * Interior lamps * To replace these lamps - see your authorized dealer. To replace all instrument panel lights - see your authorized dealer

3157K T20
921
W5W LED LED

H10 (9145)

239

Escape (TM2)

Vehicle Care

CLEANING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft® Detail Wash. • Never use strong household detergents

or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces.

• Never wash a vehicle that is “hot to the

touch” or during exposure to strong, direct sunlight.

•

• Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting. Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Motorcraft® Bug and Tar Remover.

• Remove any exterior accessories, such

as antennas, before entering a car wash.

Note: Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible. Exterior Chrome Note: Never use abrasive materials such as steel wool or plastic pads as they can scratch the chrome surface. Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers

GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft® Bug and Tar Remover (ZC-42) Motorcraft® Custom Bright Metal Cleaner (ZC-15) Motorcraft® Detail Wash (ZC-3-A) Motorcraft® Dusting Cloth (ZC-24) Motorcraft® Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft® Engine Shampoo (Canada only) (CXC-66-A) Motorcraft® Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft® Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft® Premium Quality Windshield Washer Fluid (Canada only) [CXC-37-(A, B, D or F)] Motorcraft® Premium Windshield Washer Concentrate (U.S. only) (ZC-32-A) Motorcraft® Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft® Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft® Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft® Vinyl Cleaner (Canada only) (CXC-93) Motorcraft® Wheel and Tire Cleaner (ZC-37-A)

240

Escape (TM2)

Vehicle Care

• Remove particles such as bird

droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.

• Always read the instructions before

using the products.

WAXING Regular waxing is necessary to protect your car's paint from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Always wash your vehicle before applying wax. • Use a quality wax that does not contain

abrasives. Follow the manufacturer’s instructions to apply and remove the wax.

•

• Apply a small amount of wax in a

back-and-forth motion, not in circles. • Do not allow wax to come in contact with any non-body (low-gloss black) colored trim. The wax will discolor or stain the parts over time. • Roof racks. • Bumpers. • Grained door handles. • Side mouldings. • Mirror housings. • Windshield cowl area.

• Do not apply wax to glass areas. • After waxing, your car's paint should

feel smooth, and be free of streaks and smudges.

• Wash the vehicle first, using cool or

lukewarm water and a neutral pH shampoo, such as Motorcraft® Detail Wash.

• Use Motorcraft® Custom Bright Metal

Cleaner. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.

• Do not apply cleaning product to hot

surfaces and do not leave cleaning product on chrome surfaces for a period of time exceeding that which is recommended.

• Using other non-recommended cleaners can result in severe and permanent cosmetic damage.

Underbody Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. Cleaning Plastic Exterior Parts Use only approved products to clean plastic parts •

For routine cleaning, use Motorcraft® Detail Wash. If tar or grease spots are present, use Motorcraft® Bug and Tar Remover.

•

REPAIRING MINOR PAINT DAMAGE Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color.

241

Escape (TM2)

Vehicle Care

•

To clean these items, follow these tips: The windows may be cleaned with a • non-abrasive cleaner such as Motorcraft® Ultra-Clear Spray Glass Cleaner. The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft® Premium Windshield Washer Concentrate in the U.S., or Premium Quality Windshield Washer Fluid in Canada. Be sure to replace wiper blades when they appear worn or do not function properly.

• Do not use abrasives, as they may

cause scratches

• Do not use fuel, kerosene, or paint

thinner to clean any parts.

If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water. Note: Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines. CLEANING THE INTERIOR

WARNINGS

Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the

belt webbing.

CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: •

Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.

•

• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. Spray Motorcraft® Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft® Engine Shampoo.

• Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage. • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations.

• Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine.

CLEANING THE WINDOWS AND WIPER BLADES The windows and wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield.

242

Escape (TM2)

Vehicle Care

Clean the instrument panel and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • Avoid cleaners or polishes that increase

the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect you from undesirable windshield reflection. Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces.

• Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.

• Do not allow air fresheners and hand sanitizers to spill onto interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty.

If a staining liquid like coffee or juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean,

white, cotton cloth.

2. Wipe the surface with a damp, clean, white cotton cloth. For more thorough cleaning, use a mild soap and water solution. If the spot cannot be completely cleaned by this method, the area may be cleaned using a commercially available cleaning product designed for automotive interiors. If necessary, apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area. Allow this to set at room temperature for 30
minutes.

3.

WARNINGS

On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a