2006 Ford Escape Owners Manual

MINUTE is displayed. Use SEL to manually increase ( Folder/Track mode: In MP3 mode, press MENU until MODE appears in the display. Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disc are accessible) MODE. 10. REPEAT: Press to repeat the current CD/MP3 track.

) or decrease ) the hours/minutes. Press MENU again to disengage clock mode.

) the

11. SHUFFLE: Press to play the CD/MP3 tracks on the current disc in random order. 12. FOLDER the next MP3 directory.

: Press to access

13. FOLDER the previous MP3 directory.

: Press to access

28

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

14. FF(Fast forward): In CD/MP3
mode, press until desired selection is reached. 15. REW(Rewind): In CD/MP3
mode, press until desired selection is reached. 16. SAT (if equipped): Your radio comes equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your dealer. Detailed satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. 17. BAND: Press to toggle between AM/FM1/FM2 frequency band.

18. Memory presets: To set a station: Select frequency band; tune to a station, press and hold a preset button until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.

20. CD: Press to enter CD mode.

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information.

29

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

or

21. COMP(Compression): Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press COMP to turn the feature ON/OFF. 22. Scan: Press SCAN to hear a brief sampling of radio stations or CD/MP3 tracks. Press again to stop. 23. CAT/Tune: Press to manually tune down/up the radio frequency band. CAT: CAT is only available when equipped with Satellite Radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www.siriusradio.com 24. CD slot: Insert a CD with the label side up.

30

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

Premium Satellite Compatible AM/FM Stereo/Cassette/Single CD/MP3 (if equipped)

23

22
21
20
19
18

VOL-PUSH ON

DISC

BAND

SEEK TUNE CAT

REW

DOLBY B NR

SCAN

BASS

TREB

FF

FOLDER

TEXT SEL

FOLDER

EJ

TAPE 1-2

CD

BAL

FADE

EJ

MUTE

AUX

MENU

SHUFFLE

REPEAT

17

16

15

14

13

12

11

10

1. CD slot: Insert a CD with the label side up. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. 2. CD Eject: Press to eject a CD. The radio will resume playing.

31

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

3. Mute: Press to MUTE playing media; press again to return to the playing media.

4. Tape Eject: Press to eject the cassette. The radio will resume playing. 5. Tape 1–2/CD: Press to begin tape play. If a cassette is already playing, press to change playing sides. CD: If a CD is loaded in the radio, pressing CD will cause the CD to begin playing. 6. AUX: Press to toggle between the current playing media and DVD (if equipped).

7. MENU: Press to access the following functions:

SEL

to decrease/ increase hours or minutes.

Clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Press Compression: In CD mode, press to bring soft and loud passages together for a more consistent listening level. Press MENU until COMPRESS is displayed. Use SEL to toggle on/off. Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting. Press MENU until SPEED VOL X appears in the display. Then press SEL to increase/decrease the volume setting. The level will appear in the display.

32

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

Dolby: In tape mode, press MENU until DOLBY B XX appears in the display. Press SEL to toggle ON/OFF. The Dolby威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby威 and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Folder/Track Mode: In MP3 mode, press MENU until MODE appears in the display. Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disk are accessible) MODE. Autoset: Press MENU until AUTOSET appears in the display. Press SEL to toggle on/off. Allows you to set the strongest local stations without losing your original memory preset stations for AM/FM1/FM2. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. 8. REPEAT: Press to repeat the current CD/MP3 track. Press to show repeat status. Press again to toggle status. 9. Balance: Press BAL; then press to shift sound to the SEL left/right speakers.

Fade: Press FADE; then press SEL rear/front speakers.

to shift sound to the

10. SHUFFLE: In CD/MP3 mode, press to play tracks in random order. Press to show shuffle status. Press again to toggle status. 11. TEXT/SEL: The filename, song title, artist text or album text may be viewed while playing an MP3
selection. Press TEXT to scroll through the text fields. The display will scroll through all of the text in the current field before changing to the next field. (TEXT must be pressed within three seconds of the previous

33

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

button press to proceed to the next/last text display. ) The last text field shown on the display will become the new display message default. TEXT is also available when equipped with Satellite radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. Select: Use with Bass, Treble, Balance, Fade and other menu selections. 12. FOLDER the next MP3 directory folder.

: Press to access

13. FOLDER : Press to access the previous MP3 directory folder.

14. Bass: Press BASS; then press to decrease/increase SEL the bass output.

Treble: Press TREB; then press SEL the treble output.

to decrease/increase

FF

15. Fast Forward (FF): In CD mode, press and hold to fast forward. In tape mode, press to activate fast forward. Press FF again to return to play. 16. Rewind (REW): In CD mode, press and hold to reverse CD. In tape mode, press to rewind. Press REW again to return to play. 17. Memory preset buttons: To set a station: Press BAND to select the frequency band (AM/FM1/FM2) tune to a station, press and hold a preset button until sound returns.

REW

34

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

to change frequency

18. Scan: Press to hear a brief sampling of all listenable stations, tape selections or CD tracks. Press again to stop. 19. Tune/CAT: TUNE: Works in radio mode only. Press TUNE down/up. CAT: CAT is only available when equipped with Satellite Radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit only available in the continental United States. 20. Seek: Press and release SEEK strong station, tape selection or CD track. 21. BAND: Press to toggle through AM/FM1/FM2 frequency bands.

for previous/next

22. Cassette door: Insert the cassette with the opening to the right. 23. Power/volume: Press to turn ON/OFF; turn to increase/decrease volume.

Accessory delay With accessory delay, the window switches, moon roof (if equipped) and audio system may be used for up to ten minutes after the ignition switch is turned off or until either front door is opened.

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz

35

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

the signal and the weaker the reception.

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from a station, the weaker • Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception. • Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.

Cassette/player care: Do: • Use only cassettes that are 90 minutes long or less. • Tighten very loose tapes by inserting a finger or pencil into the hole • Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity or • Clean the cassette player head with a cassette cleaning cartridge after

cold to reach a moderate temperature before playing.

and turning the hub.

10–12 hours of play to maintain good sound/operation.

Don’t: • Expose tapes to direct sunlight, extreme humidity, heat or cold. • Leave tapes in the cassette player for a long time when not being

played.

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

Don’t: • Expose discs to direct sunlight or heat sources for extended periods • Clean using a circular motion.

of time.

36

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Entertainment Systems

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Dirty, warped or damaged CDs, irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio system warranty and service: Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.

37

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control.

: Distributes outside air through the instrument panel vents. : Distributes outside air through the instrument panel vents and the

floor vents. O (OFF): Outside air is shut out and the fan will not operate.

: Distributes outside air through the floor vents. : Distributes outside air through the windshield defroster vents and

floor vents.

: Distributes outside air through the windshield defroster vents.

3. Temperature selection: Controls the temperature of the airflow in the vehicle.

the air flow selector in the

Operating tips • To reduce fog build up on the windshield during humid weather, place • To reduce humidity build up inside the vehicle during cold or warm weather, do not drive with the air flow selector in the OFF position. • Do not put objects under the front seats that will interfere with the air • Remove any snow, ice or leaves from the air intake area at the base of

flow to the rear seats.

position.

the windshield.

To aid in side window defogging/demisting in cold weather: 1. Select 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

38

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Uses recirculated air to cool the vehicle. Air flows from the instrument panel vents only. A/C: Uses outside air to cool the vehicle. Air flows from the instrument panel vents only.

: Distributes outside air through the instrument panel vents.

O (OFF): Outside air is shut out and the fan will not operate.

: Distributes outside air through the instrument panel vents and the

floor vents.

: Distributes outside air through the floor vents. : Distributes outside air through the windshield defroster vents and floor vents. The air conditioner will automatically turn on to dehumidify the air.

: Distributes outside air through the windshield defroster vents. The

air conditioner will automatically turn on to dehumidify the air. 3. Temperature selection: Controls the temperature of the airflow in the vehicle.

Operating tips • To reduce fog build up on the windshield during humid weather, place • To reduce humidity build up inside the vehicle: do not drive with the

the air flow selector in the

position.

air flow selector in the O (OFF) or MAX A/C position.

39

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Climate Controls • Under normal weather conditions, do not leave the air flow selector in

MAX A/C or O (OFF) when the vehicle is parked. This allows the vehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with the • Remove any snow, ice or leaves from the air intake area at the base of

airflow to the back seats.

the windshield.

To aid in side window defogging/demisting in cold weather: 1. Select A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to 4. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press to clear the rear window of thin ice and fog. The small LED will illuminate when activated. Ensure that the ignition is in the 3 (RUN) position in order to operate the rear window defroster. The defroster turns off automatically after 15 minutes or when the ignition is turned to the 1 (LOCK) position. To manually turn off the defroster before 15 minutes have passed, push the control a second time.

40

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

HEADLAMP CONTROL Rotate the headlamp control to the first position parking lamps. Rotate to the second position headlamps.

to also turn on the

to turn on the

Headlamp battery saver The battery saver will shut off the exterior lamps 10 minutes after the ignition switch has been turned off if the headlamp control is in the headlamp control is in the

position. The system will not shut off the parking lamps if the

position.

Autolamp control (if equipped) The autolamp system sets the headlamps to turn on and off automatically. The autolamp control, located on the headlamp switch, will: • turn on the lamps automatically • turn off the lamps automatically • keep the lamps on for up to three minutes after the key is turned to

during the daylight

at night

OFF.

See Autolamp delay system (if equipped) to set the auto headlamp off delay time.

41

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

Autolamp delay system (if equipped) If your vehicle has an autolamp delay feature, you can set the delay time to keep the headlights on for up to three minutes after the key is turned OFF. The delay time is set to 20 seconds at the factory, but the delay time may be changed by following the steps below (Steps 1 through 6
must be done within 10 seconds): 1. Turn the key to the 1 (LOCK) position. 2. Rotate the headlamp control to the autolamp position. 3. Rotate the headlamp control to the OFF position. 4. Turn the key to the 3 (RUN) position. 5. Turn the key back to the 1
(LOCK) position. 6. Turn the headlamp control to the autolamp position (the headlights should turn on). 7. Turn the headlamp control to the OFF position when the desired delay time (up to 3 minutes) has been reached.

High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.

42

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Flash to pass Pull toward you slightly to activate and release to deactivate.

Lights

Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the ignition must be in the 3 (RUN) position. • the headlamp control must be in the OFF, parking lamps or autolamp • the parking brake must be released.

position.

Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system

does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

Smart park lamps (if equipped) If your vehicle is equipped with the DRL and autolamp features, your park lamps will turn on automatically when lighting conditions are dark and DRLs are activated (the headlamp control is in the OFF position).

43

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

Foglamp control (if equipped) Press the foglamp control, located on the instrument panel, to activate the foglamps. The foglamp indicator will illuminate when the foglamps are on. Press the foglamp control to deactivate the foglamps. The foglamps will only operate with the parking lamps or headlamps on. When the highbeams are activated, the foglamps will not operate.

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to

brighten.

• Push and hold bottom of control

to dim.

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized dealer.

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

44

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

ground

• (1) 8 feet (2.4 meters) • (2) Center height of lamp to • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4
meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens. 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover the left-hand headlamp with an opaque cloth. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge of high intensity light towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted.

5. Locate the vertical adjuster on the headlamp, then use a 4 mm socket to turn the adjuster either counterclockwise (to adjust down) or clockwise (to adjust up) aligning the upper edge of the light pattern to the horizontal line. 6. Move the opaque cloth to cover the right-hand headlamp and repeat Steps 4 and 5 for the left-hand headlamp. 7. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. 8. Close the hood and turn off the lamps.

45

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn

turn signal.

signal.

INTERIOR LAMPS

Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp control has three positions: • OFF: In this position, the lamp • DOOR: In this position, the dome lamp will illuminate only when a door is opened and will remain illuminated for 25 seconds after the door is shut.

will not illuminate.

• ON: In this position, the lamp will remain illuminated. The map lamp controls (without moon roof) are located on the dome lamp. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps.

46

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

For models equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps. The map lamps will illuminate whenever a door is opened. After the door is shut, the lamps will remain illuminated for 25 seconds.

Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR

position and any door is open.

When the control is in the OFF position, it will not illuminate when you open the doors.

Interior lighting battery saver The dome and/or cargo lamps will automatically extinguish after 10
minutes when the ignition key is OFF, a door has been left open and the dome and/or cargo lamp controls are in the DOOR position. Otherwise, interior lamps including the dome and/or cargo lamps will automatically extinguish after 30 minutes when the ignition key is OFF.

BULB REPLACEMENT

Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation.

Replacing exterior bulbs Check the operation of all the bulbs frequently.

47

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

Trade number

3157 AK (amber)

Number of bulbs

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time. Function Park/turn lamps (front) Headlamps (low beams) Headlamps (high beams) Rear stop/tail/sidemarker Rear turn lamps Backup lamp Foglamp (front) Center High-mount stop lamp Rear license plate lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer

3157K or 4157K

3156
3156
H10

W5W

W5W

H11

H7

Replacing the interior bulbs Check the operation of all bulbs frequently.

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position and open the hood.

48

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

2. Press down on the wire retainer to release it and access the back of the headlamp assembly.

Lowbeam bulb replacement 3. Locate the outboard most bulb, turn it a 1⁄4 turn to the inside of the vehicle and pull the bulb socket straight out to remove the bulb.

Highbeam bulb replacement 4. Locate the bulb that is the most center in the vehicle, rotate the socket counterclockwise and pull the bulb socket straight out to remove the bulb. 5. Pull the bulb straight out of the socket and push in the new bulb. 6. To complete installation, follow the removal procedure in reverse order. Note: The bulb’s metal base gets very hot during headlamp operation. Be sure the bulb base is cool before handling. Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. To complete installation, follow the removal procedure in reverse order.

49

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

Replacing brake/tail/turn/backup lamp bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Make sure the headlamp switch is in the OFF position and then open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly. 3. Carefully remove the lamp assembly by pulling it rearward to disengage snap features on the outward side of the lamp. 4. Twist the bulb socket counterclockwise and remove from lamp assembly.

5. Pull the bulb straight out of the socket and push in the new bulb. 6. To complete installation, follow the removal procedure in reverse order.

Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position and then pry the license plate lamp assembly (located above the license plate) from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise.

50

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Lights

3. Pull the bulb out from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly turning it clockwise. 5. To install, press the lamp assembly into liftgate. Replacing high-mount brake lamp bulbs To remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate.

2. Remove the bulb holder from the lamp assembly by depressing the snaps.

3. Pull the bulb straight out of the socket and push in the new bulb. To complete installation, follow the removal procedure in reverse order.

Replacing front parking lamp/turn signal bulbs For bulb replacement, see your authorized dealer. Replacing foglamp bulbs For bulb replacement, see your authorized dealer.

51

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting.

For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF.

Mist function: To activate mist, push control up from the OFF position and release to get one wipe.

Windshield washer: To activate the windshield washer, pull control toward you. Release control to stop washer fluid spray.

52

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward to the

position.

For normal speed rear wiper operation, rotate control upward to ON.

To activate the rear washer, rotate position and the control to the release.

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down the steering column tilt lever. 2. Move the steering wheel up or down until you find the desired location. 3. Push the steering column tilt lever up. This will lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

53

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps.

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.

Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object.

CENTER CONSOLE Your vehicle is equipped with a variety of console features. These include: 1. Power point 2. Cupholders 3. Utility compartment 4. Ash cup (if equipped)

Use only soft cups in the cupholders. Hard objects

can injure you in a collision.

54

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located in the floor console. Cigarette lighter (if equipped) is located in the instrument panel. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.

POWER WINDOWS

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

55

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window. Note: The window switches will not illuminate when the window lock control is in the LOCKED position. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise; this noise can be eliminated by lowering a front window approximately two to three inches.

One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press the top part of the switch to stop.

Window lock (if equipped) The window lock feature disables all the power windows except the driver’s. To lock out all the window controls except for the driver’s window press the right side of the control. Note: The passenger window switches will not illuminate when the window control is in the LOCKED position. Press the left side to restore the window controls.

Accessory delay With accessory delay, the window switches, moon roof (if equipped) and audio system may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.

56

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

AUTOMATIC DIMMING REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function. The electrochromic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance.

EXTERIOR MIRRORS

Power side view mirrors To adjust your mirrors: 1. Rotate the control, located on the instrument panel left of the steering wheel, clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

57

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Fold-away mirrors Carefully pull the outside mirrors inwards when driving through a narrow space, like an automatic car wash.

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

ON

OFF

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

58

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

3. Press the SET ACC control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator instrument cluster will turn on.

light on the

Driver Controls

RSM SET ACC

CST

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

Resuming a set speed Press the RSM control and release it. This will automatically return the vehicle to the previously set speed. The RSM control will not work if the vehicle speed is not faster than 30 mph (48 km/h).

RSM SET ACC

CST

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACC control until you get to the desired speed, then release the control. You can also use the SET ACC control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the

RSM SET ACC

CST

vehicle reaches that speed press and release the SET ACC control.

59

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST control until you get to the desired speed, then release the control. You can also use the CST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

RSM SET ACC

CST

• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control.

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will • Press the speed control OFF

not erase your vehicle’s previously set speed.

RSM SET ACC

CST

ON

OFF

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

60

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MOON ROOF (IF EQUIPPED) To operate the moon roof: Note: The moon roof will open to the “comfort” position first before opening all the way. The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened. • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. The moon roof will open to the “comfort” position. Press and release the control again to fully open. To stop motion at any time during the one-touch opening, press the control again.

• To close, press and hold the front portion of the control. To operate the moon roof vent position: • To open, press and hold the front portion of the control. This will • To close, press and hold the rear portion of the control. Note: If the battery is disconnected, discharged, or a new battery is installed, the moon roof needs to be opened to the vent position to reset the moon roof positions. If you open and close the moon roof repeatedly, the moon roof motor may overheat and shut down for 45 seconds while the motor cools.

open the vent.

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

61

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.

Selectable features

Set This button is used to select and reset various functions shown in the INFO Menu.

Info menu This control displays the following control displays: • Average Fuel Economy • Distance to Empty • Instantaneous Fuel Economy • Fuel Available • System Check • Units (English/Metric) • Language • INFO Display on/off

62

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

service stations

Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100
km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • your vehicle was not perfectly level during fill-up • differences in the automatic shut-off points on the fuel pumps at • variations in top-off procedure from one fill-up to another • rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 8 km (5 miles) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the SET control after setting the speed control to get accurate highway fuel economy readings. Distance to empty (DTE) Selecting this function from the INFO menu will give you an estimate of how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few kilometers (miles). The DTE function will display “LOW FUEL LEVEL” and sound a tone for one second when you have low fuel level indicated on the fuel gauge.

63

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Instantaneous fuel economy Press INFO until the menu displays “INSTANT ECON”. This will display your fuel economy as a Bar Graph ranging from “L” poor economy to “H” excellent economy. Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows “L”, one or no bars illuminated. Instantaneous fuel economy cannot be reset. Fuel available Selecting this function from the INFO menu will show you how much fuel is available in your tank.

Units (English/Metric) 1. Select this function from the INFO menu for the current units to be displayed. 2. Press the SET control to change from English to Metric.

System check Selecting this function from the INFO menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the SET control cycles the message center through each of the systems being monitored.

64

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The sequence of the system check report is as follows: 1. Oil Change Reminder 2. Charging System 3. Emission Status 4. Brake System 5. Tire Pressure Monitoring System 6. Liftgate Status 7. Exterior Lamps 8. 4 Wheel Drive 9. Fuel Level Status Language 1. Select this function from the INFO menu for the current language to be displayed.

2. Pressing the SET control cycles the message center through each of the language choices.

3. Press and hold the SET control for 2 seconds to set the language choice.

Display Off Select this function from the INFO control to turn your message center display OFF.

65

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the SET control and clearing the warning message. Warning messages that have been reset are divided into two categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

This acts as a reminder that these warning conditions still exist within the vehicle. Warnings High engine temperature Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar Park brake on

Status Warning cannot be reset

Warning returns after 10 minutes

66

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Status Warning returns after the ignition key is turned from OFF to ON.

Warnings Liftgate ajar Service emission sys Check fuel cap Low brake fluid Low tire pressure Tire pressure monitor fault Tire pressure sensor fault Service brake system Check left headlamp Check right headlamp Check left high beam Check right high beam Check left turn lamps Check right turn lamps Engine change oil soon Engine oil change now Low fuel Service 4WD Turn signal on 4WD locked temporarily (if equipped) 4WD disabled temporarily (if equipped) 4WD auto restored (if equipped) HIGH ENGINE TEMPERATURE. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

Temporary alert

Never remove the coolant reservoir cap while the engine is running or hot.

67

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

DRIVER DOOR AJAR. Displayed when the driver door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR. Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR. Displayed when the rear right door is not completely closed. LIFTGATE AJAR. Displayed when the liftgate or liftgate glass is not completely closed. Press SET to reset display. PARK BRAKE ON. Displayed when the park brake is on. If the warning stays on after the park brake is off, contact your authorized dealer as soon as possible. CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and Specifications chapter. SERVICE EMISSION SYS. Displayed when the engine has defaulted to a ’limp-home’ operation. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer SERVICE BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK LEFT OR RIGHT HEADLAMPS. Displayed when the headlamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter.

68

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CHECK LEFT OR RIGHT HIGH BEAMS. Displayed when the headlamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK LEFT OR RIGHT TURN LAMPS. Displayed when the turn signals are activated and at least one is burned out. Check the lamps as soon as safely possible and have the burned out lamp replaced. LOW FUEL. Displayed as an early reminder of a low fuel condition. SERVICE 4WD. Displayed when the 4X4 is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. TURN SIGNAL ON. Displayed when the turn signal is activated and the vehicle is driven more than 2 miles (3.3 km). 4WD LOCKED TEMPORARILY (if equipped). Displayed when the 4X4 is temporarily locked. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. 4WD DISABLED TEMPORARILY (if equipped). Displayed when the 4X4 is temporarily disabled. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. 4WD AUTO RESTORED (if equipped). Displayed when the 4X4 is restored to normal operations. ENGINE OIL CHANGE SOON/ENGINE OIL CHANGE NOW. Displayed when the engine oil life remaining is 5% or less. When oil life left is between 5% and 0%, the ENGINE OIL CHANGE SOON message will be displayed. When oil life left reaches 0%, the ENGINE OIL CHANGE NOW message will be displayed. An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 12 months] perform the following: 1. Select this function from the INFO menu then press the SET control to access the system check function.

69

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

2. Press and release the SET control to display “OIL CHNG XXX% HOLD SET NEW”.

3. Press and hold the SET control for 2 seconds to display “OIL CHANGE SET TO 100%”.

INFO UNAVAIL. These messages indicate improper operation of the vehicle network communication systems for the following vehicle modules. • Fuel computer • Charging system • Door sensor • Brakes • Exterior lamps • Emissions system • 4WD info Contact your Ford Dealer as soon as possible if these messages occur on a regular basis.

LIFTGATE To open the rear window, pull the right side of the liftgate handle. To open the liftgate, pull the left side of the liftgate handle. • Do not open the liftgate or

liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be damaged against a low ceiling.

70

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls • Do not leave the liftgate or liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.

Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.

Exhaust fumes contain carbon monoxide which can injure your lungs and cause drowsiness and even death. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.

CARGO SHADE (IF EQUIPPED) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. To install the shade: • Insert the ends of the cargo

shade into the mounting features located behind the rear seat on the rear trim panels.

To operate the shade: 1. Grasp the handle at the rear edge of the shade and pull rearward. 2. Secure both ends of the support rod into the retention slots located on the rear quarter trim panels.

Ensure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is

not securely installed.

Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of vehicle in the case of

a sudden stop or collision.

71

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Cargo management system (if equipped) The cargo management system consists of a storage compartment located in the floor of the rear cargo area. 1. To open, lift the release handle and the lid. The lid can be removed to allow for extra storage. 2. To close, lower the lid and push handle until latch clicks.

This storage compartment is not designed to restrain objects during a collision with the lid removed.

LUGGAGE RACK Your vehicle may be equipped with a roof rack. The maximum load for the roof rack is 100 lbs (44 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars as possible. Do not use the vehicle’s door handles as tie down loops. To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar.

72

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To remove the cross-bar assembly (if equipped) from the roof rack side rails: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable).

2. Slide the cross-bar to the end of the rail.

3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar. 4. Slide the cross-bar assembly off the end of the rail.

73

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle.

2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar. 3. Slide the cross-bar assemblies over the end cap tongue and into the side rails.

4. Tighten thumbwheel at both ends of the cross-bar.

74

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer. Refer to the SecuriLock娂 passive anti-theft system section later in this chapter for more information.

POWER DOOR LOCKS The power door lock controls are located on the driver and front passenger door panels. Pressing the doors. Pressing the the doors.

will unlock all the will lock all

Power door lock/unlock inhibit feature As a theft deterrent, the power door lock controls can be disabled 20
seconds after the ignition has been turned to the 1 (LOCK) position and the vehicle is locked using the remote entry transmitter or the key in the door lock cylinder. The door lock controls are enabled when the vehicle on is unlocked using the key in the door lock cylinder or by pressing the remote entry transmitter. This feature can be turned on or off using the following procedure: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. 1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. Press the power door lock control on the door panel two times within five seconds. The horn will chirp two times to confirm the feature is off; the horn will chirp two times and honk one time to confirm the feature is on.

75

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

7. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off.

Door key unlocking/locking Two step door unlocking 1. Turn the key in the door cylinder to unlock the driver’s door. Note: The interior lamps will illuminate if the control on the overhead lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate. For more information, refer to Illuminated entry later in this chapter. 2. Turn the key in the door cylinder again within three seconds to unlock the passenger doors, the liftgate and liftgate glass. One step door unlocking If the one step door unlocking feature is activated, turn the key in the door cylinder once to unlock all of the doors , the liftgate and liftgate glass. Note: The interior lamps will illuminate (refer to the Illuminated entry feature later in this section), if the control on the overhead lamp is in the DOOR position. For information on switching from two step to one step door unlocking, refer to Switching from two step to one step door unlocking later in this chapter. Locking the doors Turn the key in the door cylinder to lock all the doors. The park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. If any of the doors, the liftgate or the hood are not properly closed the park/turn lamps will not flash.

Autolock (if equipped) The autolock feature automatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (RUN) position, • the brake has been released and • the vehicle has been set in motion.

76

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

closed, and

Relock This feature will also automatically relock all the doors when: • the ignition is in the 3 (RUN) position and any door is opened then • you put the vehicle in motion by releasing the brake pedal. Deactivating/activating the autolock feature The autolock feature can be turned on or off using the following procedure: Before starting, make sure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1-5 within 30 seconds or the procedure will have to be repeated. 1. Turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control (on the door panel) three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control three times. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. 6. The horn will chirp once to confirm programming mode is entered/active. 7. Press the power door unlock control on the door panel one time. 8. Press the power door lock control on the door panel one time. Note: The horn will chirp once to confirm the feature is OFF, or the horn will chirp and then honk to confirm the feature is ON. 9. Turn the ignition to the 1 (LOCK) position. Note: The horn will chirp once to confirm the programming mode has been exited. Repeat the previous procedure to turn the feature on or off.

Smart unlocking feature The smart unlocking feature helps prevent you from locking yourself out of the vehicle. With the key in any ignition position, the driver’s door will automatically unlock if it is locked using the power lock control on the driver’s door panel while the driver’s door is open.

77

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS • When these locks are set, the

rear doors cannot be opened from the inside.

• The rear doors can be opened

from the outside when the doors are unlocked.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Rotate lock control in the

direction of arrow to engage the lock.

• Rotate control in the opposite

direction to disengage childproof locks.

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, • other vehicles parked next to your vehicle, or 78

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• weak or dead transmitter battery. The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote locking and unlocking features will operate independent of the ignition position; however, the panic feature will only operate when the ignition is in the 1
(LOCK) or 2 (ACCESSORY) position. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.

and release again within three seconds to unlock the

and release to unlock the driver’s door. Note: The interior

Two step door unlocking 1. Press lamps will illuminate if the control on the overhead lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate. 2. Press passenger doors, the liftgate and liftgate glass. The battery saver feature will turn off the interior lamps 30 minutes after the ignition is turned to the 1 (OFF/LOCK) position. One step door unlocking and release If the one step door unlocking feature is activated, press once to unlock all of the doors, the liftgate and liftgate glass. Note: The interior lamps will illuminate (refer to the Illuminated entry feature later in this section), if the control on the overhead lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate. Switching from two step to one step door unlocking Unlocking can be switched between two step and one step door unlocking by pressing and holding both simultaneously on the remote entry transmitter for approximately 4
seconds. The parklamps will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two step unlocking.

buttons

and

79

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. and release again within three seconds to confirm that all the 2. Press doors and liftgate are closed and locked. Note: The doors will lock again and the horn will chirp once. If any of the doors or the hood are not properly closed, the horn will control is chirp twice and park/turn lamps will not flash when the pressed.

to activate the alarm. To deactivate the feature, press the

Sounding a panic alarm Press control again, turn the ignition to the 3 (RUN) or 4 (START) position, or wait for the alarm to time out in approximately 3 minutes. Note: The panic alarm will only operate when the ignition is in the 1
(LOCK) or 2 (ACCESSORY) position.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

80

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. Note: If all remote entry transmitters are not present during the programming procedure, the missing transmitters will not work with the vehicle following programming.

81

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

To reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed. 8. Repeat Step 6 to program each additional remote entry transmitter. 9. Turn the ignition to the 1 (LOCK) position after you have finished programming all of the remote entry transmitters. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 2 (ACCESSORY) position, or • the remote transmitter lock control is pressed, or • the doors are locked by key in the door cylinder, or 82

2006 Escape (204) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• after 25 seconds of illumination. Illuminated exit • The interior lights will illuminate when the key is removed from the

ignition.

The lamps automatically turn off after 25 seconds. The dome and cargo lamp controls must not be set to the OFF position for the illuminated exit system to operate.

KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to lock or unlock the doors without using a key. The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Anti-scan feature If an incorrect code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash during this