Download PDF Manual


AM FM


CD


54


Controls and features


PUSH ON


Volume/powercontrol Press the control to turn the audio system on or off.


Turn the control to raise or lower volume.


If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FMselect The AM/FM select control works in radio and CD modes.


AM FM


CD


AM/FMselectinradiomode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FMselectinCDmode Press this control to stop CD play and begin radio play. Tuneadjust The tune control works in radio or CD mode.


55


Controls and features


Tuneadjustinradiomode • Press


to move to the next


frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.


• Press


to move to the next frequency up the band (whether or not


a listenable station is located there). Hold for quick movement.


TuneadjustforCDmode • Press


to select the previous disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs.


• Press


through the remaining discs.


to select the next disc. Hold the control to fast-forward


Seekfunction The seek function works in radio or CD mode. Seekfunctioninradiomode • Press


to find the next listenable station down the frequency band. SEEK DOWN will display.


• Press


SEEK UP will display.


to find the next listenable station up the frequency band.


56


Controls and features


SeekfunctioninCDmode • Press


to seek to the previous


track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing.


• Press


to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.


Scanfunction The scan function works in radio or CD mode.


Scanfunctioninradiomode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. ScanfunctioninCDmode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Radiostationmemorypreset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Settingmemorypresetstations 1. Select the frequency band with the AM/FM select control. Press the AM/FM control to toggle between AM, FM1, or FM2. 2. Press the SEEK control to access the next listenable station up or down the frequency band. Press the TUNE control to go up or down the listening band in individual increments. 3. Select a station. Refer to Seek function for more information on selecting a station.


57


Controls and features


4. Press and hold a memory preset control. The playing media will mute momentarily. When the sound returns, the station is held in memory on the control you selected. The display will read SAVED.


Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Startingautostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display as the frequency band is scrolled through. 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the AM/FM control again.


58


Controls and features


CDselect CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. If an alternative CD is desired, press the corresponding preset control (1–6) of a loaded CD, or press the TUNE control to access the other loaded CDs. NO CD will display if the CD control is activated when there is not a CD present in the audio system. NO CD will illuminate in the display if the CD control and a present number (that is currently empty) are pressed. The system will play the next available disc. If your vehicle is equipped with a CD changer, pressing the CD control again will allow you to toggle between accessing the multi disc system and the CD changer. The display will read CD or CDDJ. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Displaydescription Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot. Load The load feature allows you to load single CDs into the player internal to the radio.


This six disc CD player is equipped with a CD door. Compact discs should only be inserted into the player after the door has been opened by the player. Do not attempt to force the door open. Compact discs should only be loaded by pressing the LOAD control.


59


Controls and features


Press the LOAD control. (You can choose which slot will be loaded by pressing the desired preset number. If you do not choose a slot, the system will choose the next available one.) Wait until the CD door opens. Load the CD into the player. LOADING CD# is displayed. When the CD has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2. Autoload This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio.


Press and hold the LOAD control until AUTOLOAD # is displayed. The CD door will open. Load the desired disc, one at a time. The CD is loaded into position and the audio system will display CD#. Each time the CD door opens, INSERT CD# is displayed. The door will close and the player will move to the next slot after each disc has been loaded. The process is repeated until all 6 slots are full. The audio system plays the last CD loaded and the display is updated. If some slots are already full and autoload is activated, the system will fill all empty slots. Eject Press the EJ control to stop and eject a CD. You can choose which CD will be ejected by pressing the EJ control and the desired preset number (1–6). For example, to eject CD 2, press the EJ control and then press the preset 2 control. If you do not choose a specific CD, the player will eject the current CD. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF.


60


Controls and features


Autoeject Press and momentarily hold the EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF. Rewind The rewind control works in CD modes. Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode. When in rewind mode, your audio system will automatically lower the volume level of the playing media. Fastforward The fast forward control works in CD modes. Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track. Release the control to disengage fast forward mode. When in fast forward mode, your audio system will automatically lower the volume level of the playing media.


61


Controls and features


Shufflefeature Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode. When engaged, the shuffle feature has two different modes: SHUFFLE DISC and SHUFFLE TRK. SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system. SHUFFLE TRK plays all the tracks on the current disc in random order. Compressionfeature The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistent listening level.


MENU


SEL


Press the MENU control until compression status is displayed. Press the SEL control to enable the compression feature when COMP OFF is displayed. Press the SEL control again to disable the feature when COMP ON is displayed.


62


Controls and features


Bassadjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Trebleadjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble. Speakerbalanceadjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speakerfadeadjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.


BASS


TREB


BASS


TREB


BAL


FADE


BAL


FADE


SEL


SEL


SEL


SEL


63


Controls and features


MENU


Menumode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available. If RDS is turned OFF, you can access the following: • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES — Refer to Setting the clock. • RDS OFF — Refer to Radio data system feature. If RDS is turned ON, you can access the following: • TRAFFIC ON/OFF-Refer to Traffic announcements. • FIND type-Refer to Program type. • SHOW (NAME, TYPE, NONE)- Refer to Radio data system feature. • RDS ON— Refer to Radio data system feature. • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES —Refer to Setting the clock. When in CD mode, you can access: SELECT HOURS, SELECT MINUTES or COMP ON/OFF. SELECT HOURS, SELECT MINUTES— Allows you to adjust the hours and minutes. Refer to Setting the clock. TRAFFIC ON/OFF— Traffic announcements can be programmed as local or distant. Refer to Traffic announcements. RDS ON/OFF— This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Refer to Radio Data System feature. FIND type — Allows you to select your desired FM program type and search for that selection. SHOW — Allows you to select from NAME (displays the name of the radio station), TYPE (displays the RDS program type: rock, jazz, etc.), or NONE (deactivates the RDS display).


64


Controls and features


SEL


MENU


Trafficannouncements This feature allows you to hear traffic announcements. When in this mode, traffic announcements will interrupt radio and CD play. When in FM mode and RDS is activated, press the MENU until TRAFFIC OFF displays. Press the SEL control to engage the feature. The display will read TRAFFIC ON. This feature also allows you to control the volume of traffic announcements. With the display reading TRAFFIC ON, adjust the volume using the volume control to the desired level. The volume level will show at the bottom of the display. Interrupting traffic announcements will be at the selected volume level. To disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF. RDStrafficseekfeature When in traffic mode, you can use the SEEK feature to seek up or down the listenable traffic capable frequencies. With the RDS activated, press MENU until TRAFFIC ON is displayed. Press and hold the SEEK control until the desired selection is reached. The feature disengages when the control is released. RDStrafficscanfeature When in traffic mode, you can use the SCAN feature to scan up the frequency band for listenable traffic capable frequencies. With the RDS activated, press the MENU control until TRAFFIC ON is displayed. Press the SCAN control. SCAN TRAFFIC will display. The audio system will scan to all traffic capable frequencies. If no valid stations are found after one pass, the scan function is cancelled and NOT FOUND displays.


65


Controls and features


SEL


MENU


Radiodatasystem(RDS)feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections: Trafficannouncements This feature allows you to hear traffic announcements while in CD mode. These announcements are broadcast by traffic capable RDS stations. When in this mode, traffic announcements will interrupt radio and CD play. • Press the MENU control until TRAFFIC is displayed. • Press the SEL control to engage the feature. The display will read


TRAFFIC ON.


This feature also allows you to control the volume of traffic announcements. With the display reading TRAFFIC ON, adjust the volume using the volume control to the desired level. The volume level will show at the bottom of the display. Interrupting traffic announcements will be at the selected volume level. To disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF. Traffic announcements are not available in most U.S. markets. Programtype This feature allows you to search for RDS stations selectively by their program type.


66


Controls and features


MENU


Press the MENU control until FIND program type is displayed. Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R & B • Religious • Rock • Soft • Top 40
Show This feature allows you to select the type of RDS broadcast information the radio will regularly show in the display.


MENU


SEL


SEL


With RDS activated, press the MENU control until SHOW is displayed. Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display). Digitalsignalprocessing The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes.


MENU


SEL


67


Controls and features


SEL


DSP


Press the DSP control to access the DSP menu. Press the SEL control to enter one of the following modes: • DSP OFF • SIGNAL MODE • OCCUPANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: • DSP OFF—disengages the feature • NEWS—”voice-only” type of sound with a limited audio band • JAZZ CLUB—jazz club with clearly reflected sounds • HALL—rectangular concert hall capacity of about 2 000
• CHURCH—church with a high vault • STADIUM—outdoor stadium with a capacity of about 30 000
Press the DSP control again to access the Occupancy Modes. Use the SEL control to optimize the sound based upon the occupants in the vehicle. The following occupancy modes can be selected: • ALL SEATS — Optimizes the acoustic sound for all seating locations.


SEL


Rear seat performance may be compromised in the interest of the front seats. • DRIVER SEAT — Optimizes the acoustic sound for the driver. Rear


seat and passenger seat performance may be compromised in favor of the driver.


• REAR SEATS- Optimizes the acoustic sound for the rear seat passengers and reduces the audio level in the front speakers. This enables the front seat passengers to speak while the rear seat passengers listen to the audio system.


Mutemode Press the control to mute the playing media. Press the control again to return to the playing media.


68


Controls and features


(cid:83)(cid:69)(cid:76)


Settingtheclock Press the MENU control until SELECT HOUR or SELECT MINUTE is displayed. (The menu mode must be engaged to enable clock mode). Use the SEL control to manually set the time. • Press • Press


hours/minutes.


to decrease


to increase


hours/minutes.


Press the MENU control again to disengage the clock mode.


Troubleshooting the CD changer (if equipped)


The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case.


If sound skips: • You may be traveling on a rough road, playing badly scratched discs or


the disc may be dirty. Skipping will not scratch the discs or damage the player.


If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc. • The disc is inserted with the label surface downward. • The disc is dusty or defective. • The player’s internal temperature is above 60°C (140°F). Allow the • A disc with format and dimensions not within industry standards is


player to cool down before operating.


inserted.


Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion.


69


Controls and features


CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended • Do not insert more than one disc into each slot of the CD changer


periods of time.


magazine.


Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.


Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. Radioreceptionfactors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.


• Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.


• Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.


The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.


70


Controls and features


Audio system warranties and service Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or a qualified technician.


POSITIONS OF THE IGNITION 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. RUN, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts.


TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn


turn signal.


signal.


OFF


71


Controls and features


MANUAL TILT STEERING COLUMN (IF EQUIPPED) Push the tilt steering wheel lever downward to move the steering wheel up or down. Pull the control up into the original position to lock the steering wheel in position.


Never adjust the steering wheel when the vehicle is moving.


72


Controls and features


SPEED CONTROL (IF EQUIPPED)


To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.


ON


OFF


Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.


To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased.


To set a speed • Press SET ACC. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).


ON


OFF


RSM SET ACC


CST


If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.


73


Controls and features


If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RSM will re-engage it.


Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.


To set a higher set speed • Press and hold SET ACC. Release


the control when the desired vehicle speed is reached or • Press and release SET ACC to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or


RSM SET ACC


CST


• Accelerate with your accelerator pedal. When the desired vehicle


speed is reached, press and release SET ACC.


You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.


To set a lower set speed • Press and hold CST. Release the control when the desired speed is reached or • Press and release CST to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When


the desired vehicle speed is reached, press SET ACC.


74


RSM SET ACC


CST


RSM SET ACC


CST


Controls and features


To disengage speed control • Depress the brake pedal or


• Depress the clutch pedal (if


equipped).


Disengaging the speed control will not erase the previously programmed set speed.


Pressing OFF will erase the previously programmed set speed.


To return to a previously set speed • Press RSM. For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph).


ON


OFF


RSM SET ACC


CST


75


Controls and features


WINDSHIELD WIPER AND WASHER For intermittent operation, move control down one position.


Adjust the rotary control to the desired speed setting.


For normal or low speed wiper operation, move control down two positions from OFF.


For high speed wiper operation, move control down three positions from OFF.


76


Controls and features


To activate the windshield washer, pull control toward you. Release control to stop washer fluid spray.


MIST FUNCTION Move control up and release for one wipe.


Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward to the INT position.


For normal speed rear wiper operation, rotate control upward to ON.


77


Controls and features


To activate the rear washer, rotate the control to the position and release.


OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.


Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object.


Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the Velcro pad from the storage compartment door. • Place Velcro on aftermarket


transmitter opposite of actuator control.


• Install the transmitter on to storage compartment door aligning the actuator control with the rubber plunger.


• Close the door and press the


storage compartment door to activate the transmitter.


78


Controls and features


MOON ROOF (IF EQUIPPED) To operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control a second time.


open the vent.


• To close, press and hold the front portion of the control. To operate the moon roof vent position: • To open, press and hold the front portion of the control. This will • To close, press and hold the rear portion of the control. If the battery is disconnected, discharged, or a new battery is installed, the moon roof needs to be opened to the vent position to reset the moon roof positions. If you open and close the moon roof repeatedly, the moon roof motor may overheat and shut down for 45 seconds while the motor cools.


Do not let children play with the moon roof. They may seriously injure themselves.


INTERIOR LAMPS


Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp will stay on if the control is moved to the passenger side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the driver’s side position, the lamp will not come on at all.


79


Controls and features


With the control in the middle position, the dome lamp will illuminate whenever any door is opened. If any door has been opened from the outside, the lamp will remain on for 15 seconds after the door is shut. The map lamp controls (without moon roof) are located on the dome lamp. Press the controls on either side of each map lamp to activate the lamps.


If equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the controls on either side of each map lamp to activate the lamps. This map lamp will illuminate whenever any door is opened. If any door has been opened from the outside, the lamp will remain on for 15 seconds after the door is closed.


Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR position and any door is open. • the headlamp control is rotated


fully counterclockwise.


When the control is in the OFF position, it will not illuminate when you open the doors or fully rotate the headlamp control.


80


Controls and features


HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Your vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF position.


OFF


Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or Parking lamps position.


Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.


High beams • Push forward to activate. • Pull toward you to deactivate.


OFF


81


Controls and features


Flash to pass Pull toward you to activate and release to deactivate.


Foglamp control (if equipped) Turn on the parking lamps. Press the foglamp control, located on the instrument panel, to activate the foglamps. The foglamp LED will illuminate when the foglamps are on. Press the foglamp control to deactivate the foglamps.


OFF


POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the


rocker switch to close.


82


• Press the bottom portion of the


rocker switch to open.


Controls and features


One touch down • Press AUTO completely down to the second detent. The driver’s window will open fully. Depress up to stop window operation.


Window lock (if equipped) The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the right side of the control. NOTE: The window switches will not illuminate when the window control is in the LOCKED position. Press the left side to restore the window controls.


83


Controls and features


POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors.


Press control to lock all doors. NOTE: The power door switches will not illuminated when the window lock switch is in the LOCKED position.


CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Rotate lock control in the direction of arrow to engage the lock. Rotate control in the opposite direction to disengage childproof locks.


84


Controls and features


CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment • Cupholders • Ashcup


Use only soft cups in the cupholder. Hard objects can injure you in a collision.


AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. An additional auxiliary power point is located in the cargo area (if equipped). Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.


85


Controls and features


CARGO AREA FEATURES


Cargo cover (if equipped) Your vehicle may be equipped with a cargo area shade that covers the luggage compartment of your vehicle. To install the shade: 1. Fasten the cover into the mounting brackets (make sure the cover is right side up). 2. Pull the end of the shade toward you and hook the sides into the notches (right side first) in the rear trim panels.


To reduce the risk of injuries, the fasteners for


cargo area cover must be properly attached to the mounting clips on the rear trim panels.


Do not place any objects on the cargo area cover. They may obstruct your vision or strike occupants of the vehicle in the


case of a sudden stop or collision.


The cover may cause injury in a sudden stop or accident if it is not securely installed.


Cargo table (if equipped) Your vehicle may be equipped with a cargo table that is located behind the rear seat of your vehicle which can be used to store and compartmentalize cargo and be used as a picnic table.


86


Controls and features


To remove the cargo table: 1. Push the button in the center of the table to unlock it. Lift up either side of the table to disengage from the trim panels. 2. Fold the table in half and remove it from the cargo area. To install the cargo table: 1. Set the table in the cargo area like a bi-fold table. 2. Insert both feet from one side of the table into the holes in the trim panel then repeat on the other side. 3. Check and make sure that all four feet are properly seated into the holes of the trim panel and the hinge is locked.


87


Controls and features


To use the cargo table: • To store items under the table in the cargo area, unhook and lift the panels in the table. • To use as a picnic table, remove


the table from the cargo area, unfold it and extend the legs.


To reduce the risk of injuries, all four feet must


be properly seated in the notches on the rear trim panels and the hinge must be locked.


Do not place any objects on the cargo table. They may


obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision.


88


Controls and features


LIFTGATE To open the rear window, pull the right side of the liftgate handle. To open the liftgate, pull the left side of the liftgate handle. • Do not open the liftgate or


liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be damaged against a low ceiling. • Do not leave the liftgate or


liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.


Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This


will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.


REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the LOCK position.


89


Controls and features


If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.


Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. The flashers will flash twice to confirm the vehicle is unlocked. Press the control a second time within three seconds to unlock all doors.


Locking the doors Press this control to lock all doors. If all doors are closed, the flashers will flash once and the perimeter alarm (if equipped) will be armed. If the control is pressed a second time within three seconds the doors will lock again and the horn will chirp.


Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again.


90


Controls and features


Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together.


Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s


transmitters to your dealer for programming, or


• Perform the programming


procedure yourself


91


Controls and features


Programmingremotetransmitters It is necessary to have all(maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Insert a key in the ignition and turn from 1 (LOCK) to 3 (RUN) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 3
(RUN) position. The doors will lock/unlock to confirm that programming mode has been entered. • Within 20 seconds, program a


remote transmitter by pressing any button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.)


• Repeat the previous step to program additional remote transmitters.


The doors will lock/unlock to confirm that each remote transmitter has been programmed. • When you have completed programming the remote transmitters, turn


the ignition to 1 (LOCK) or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.


Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The system automatically turns off after 30 seconds or when the ignition is turned to the RUN position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on in the dome lamp control or • any door is open


92


Controls and features


The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position.


SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.


Automatic arming The vehicle is armed approximately 15 seconds after switching the ignition to the 2 (ACC) position. The THEFT light in the instrument cluster will flash every two seconds when the vehicle is armed.


Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. The THEFT light will illuminate for three seconds and then go out. If the THEFT light stays on for an extended period of time or flashes rapidly, have the system serviced by your dealership or a qualified technician.


Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your dealership. Your dealership can program your key or you can “do it yourself”, refer to Programming spare keys.


93


Controls and features


Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the coded key may cause vehicle starting issues. If present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a momentary NO—START condition if they are too close to the key during engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key. If your keys are lost or stolen you will need to do the following: • Use your spare key to start the • Have your vehicle towed to a


vehicle, or


dealership or locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded.


Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle. The use of the wrong type of coded key may lead to a “NO-START” condition. If an unprogrammed key is used in the ignition it will cause a “NO START” condition.


Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock娂 keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily


94


Controls and features


accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your dealership to have the spare coded key(s) programmed. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 2
(ACC) to 3 (RUN) (maintain ignition in 3 (RUN) for at least one second). 2. Turn ignition to 1 (LOCK) and remove the first coded key from the ignition. 3. Within ten seconds of turning the ignition to 2 (ACC), insert the second previously programmed coded key into the ignition and turn the ignition from 2 (ACC) to 3 (RUN) (maintain ignition in 3 (RUN) for at least one second but no more than ten seconds). 4. Turn the ignition to 1 (LOCK) and remove the second coded key from the ignition. 5. Within 20 seconds of turning the ignition to 2 (ACC), insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from 2 (ACC) to 3 (RUN) (maintain ignition in 3 (RUN) for at least one second). This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat this procedure from step 1. If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will illuminate for three seconds and then go out. If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off and you may repeat steps 1
through 6. If failure repeats, bring your vehicle to your dealership to have the new spare key(s) programmed.


PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle from unauthorized entry.


95


Controls and features


If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.


Arming the system When armed, this system will help protect your vehicle from unauthorized entry. When unauthorized entry occurs, the system will flash the headlamps, parking lamps and will sound the horn. The system is ready to arm whenever the key is removed from the ignition. Either of the following actions will prearm the alarm system: • Press the remote entry lock • Lock the doors using the key.


control.


If a door is open, the system is not armed. The system will become prearmed when all doors are closed. When the system becomes prearmed the flashers will flash to confirm the prearming. Once the system is prearmed, the system will arm in 20 seconds. If any door is opened during these 20 seconds, the arming will be canceled.


Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your • Unlock the doors with a key.


remote entry transmitter.


96


Controls and features


• Press the panic control on the remote entry transmitter. This will disarm the system only if the alarm is sounding.


97


Seating and safety restraints


SEATING


Adjusting the front manual seat


Never adjust the driver’s seat or seatback when the vehicle is moving.


Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision.


Lift handle to move seat forward or backward.


98


Seating and safety restraints


Pull lever up to adjust seatback.


Adjusting the front power seat (if equipped)


Never adjust the driver’s seat or seatback when the vehicle is moving.


Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision.


The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion.


99


Seating and safety restraints


Press to raise or lower the rear portion of the seat cushion.


Press the control to move the seat forward, backward, up or down.


Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’s seat. Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness.


REAR SEATS


Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.


100


Seating and safety restraints


The head restraints can be moved up and down.


Push control to lower head restraint.


Folding down rear seats 1. Raise the rear seat head restraint and remove.


101


Seating and safety restraints


2. Place the head restraint under the front seat for storage.


3. Pull the seat release control.


NOTE: Make sure the floor is clear of all objects before folding the seat.


102


Seating and safety restraints


4. Flip seat forward.


5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE: When the seatback release strap is pulled use your other hand to guide the seatback.


103


Seating and safety restraints


6. Rotate seatback down into load floor position.


Make sure seat belt buckle heads are not trapped


underneath the seatback and that the seat belt buckle heads are fully extended towards the front of the vehicle. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down.


Returningtherearseatstouprightposition 1. Pull seatback up and into upright position making sure seatback locks into place. While holding the seatback, pull the release and push seatback backward into the desired position.


104


Seating and safety restraints


2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed.


3. Remove the head restraint stored under the front seat and return it to the original position on the seat back.


105


Seating and safety restraints


Toremovetherearcushion 1. Pull the Yellow tab 2. Pull the cushion to the outboard side of the vehicle.


Toinstalltherearcushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place.


106


Seating and safety restraints


SAFETY RESTRAINTS


Safety restraints precautions


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


To reduce the risk of injury, make sure children sit where they can be properly restrained.


Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from


injury in a collision.


All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is


provided.


It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas


are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.


In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.


Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that


are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.


107


Seating and safety restraints


Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.


Energy Management Feature • This vehicle has a safety belt system with an energy management


feature at the front seating positions to help further reduce the risk of injury in the event of a head-on collision.


• This safety belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.


After any vehicle collision, the safety belt system at all outboard seating positions (except driver, which has no “automatic locking retractor” feature) must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.


BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked according to the procedures in Workshop Manual.


Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.


Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.


108


Seating and safety restraints


2. To unfasten, push the release button and remove the tongue from the buckle.


The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below:


Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.


Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. Whentousetheautomaticlockingmode • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter.


109


Seating and safety restraints


Howtousetheautomaticlockingmode • Buckle the combination lap and


shoulder belt.


• Grasp the shoulder portion and pull downward until the entire belt is extracted.


• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.


Howtodisengagetheautomaticlockingmode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.


110


Seating and safety restraints


After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that


the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.


BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual.


Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.


Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.


Position the shoulder belt height adjusters so that the


belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.


111


Seating and safety restraints


Lap belts Adjustingthecenterlapbelt The lap belt does not adjust automatically.


The lap belt should fit snugly and as low as possible around the hips, not across the waist.


Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.


Shorten and fasten the belt when not in use.


Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8
inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost.


112


Seating and safety restraints


Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso.


Then... The safety belt warning light illuminates 1 minute and the warning chime sounds 6 seconds.


Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditionsofoperation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...


The safety belt warning light and warning chime turn off.


The safety belt warning light and indicator chime remain off.


BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster.


113


Seating and safety restraints


If... The driver’s safety belt is not buckled approximately 5
seconds after the safety belt warning light has turned off and vehicle speed exceeds 8km/h (3 mph)...


Then... The BeltMinder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30
seconds, repeating for approximately 5 minutes or until safety belt is buckled. The BeltMinder feature will not activate.


The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... ⬙Crashes are rare events⬙


The BeltMinder feature will not activate.


Consider... 36 700 crashes occur every day. The more we drive, the more we are exposed to ⬙rare⬙ events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 3 of 4 fatal crashes occur within 25
miles of home.


⬙I’m not going far⬙


114


Reasons given... ⬙Belts are uncomfortable⬙


⬙I was in a hurry⬙


⬙Seat belts don’t work⬙


⬙Traffic is light⬙


⬙Belts wrinkle my clothes⬙


⬙The people I’m with don’t wear belts⬙


⬙I have an air bag⬙


⬙I’d rather be thrown clear⬙


Seating and safety restraints


Consider... Ford designs its safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident. BeltMinder reminds us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4
times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T ⬙PICK OUR CRASH⬙.


115


Seating and safety restraints


Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of


injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.


Onetimedisable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, BeltMinder will be disabled for that ignition cycle only. Deactivating/activatingtheBeltMinderfeature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure. The BeltMinderfeature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • the parking brake is set • the gearshift is in P (Park) (automatic transmission) or the neutral • the ignition switch is in the OFF position • all vehicle doors are closed • the driver’s safety belt is unbuckled • the parklamps/headlamps are in OFF position (If vehicle is equipped


position (manual transmission).


with Autolamps, this will not affect the procedure.)


To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle.


1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1–2
minutes) • Steps 3–5 must be completed within 60 seconds or the procedure will


have to be repeated.


3. Uncoil then retract the safety belt three times, ending with the safety belt retracted. This can be done before or during BeltMinderwarning activation.


116


Seating and safety restraints


4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps. 5. Uncoil then retract the safety belt three times, ending with the safety belt retracted. • After step 5 the safety belt warning light will be turned on for three


seconds.


6. Within seven seconds of the safety belt warning light turning off, uncoil then retract the safety belt. • This will disable BeltMinderif it is currently enabled, or enable


BeltMinder if it is currently disabled.


7. Confirmation of disabling BeltMinderis provided by flashing the safety belt warning light four times per second for three seconds. 8. Confirmation of enabling BeltMinderis provided by flashing the safety belt warning light four times per second for three seconds, followed by three seconds with the safety belt warning light off, then followed by flashing the safety belt warning light four times per second for three seconds again. 9. After receiving confirmation, the deactivation/activation procedure is complete.


Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.


117


Seating and safety restraints


Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe


personal injuries in the event of a collision.


Refer to Cleaning and maintaining the safety belts in the Maintenacne and Care section.


AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)


Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford Motor Company in the servicing vehicle and helping to better understand real world collisions and further improve the safety of future vehicles.


118


Seating and safety restraints


Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.


All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is


provided.


Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.


National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches)


between an occupant’s chest and the driver air bag module.


Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.


Steps you can take to properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the • Recline the seat slightly (one or two degrees) from the upright


pedals comfortably.


position.


119


Seating and safety restraints


Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those


objects to be propelled by the air bag into your face and torso causing serious injury.


Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or


Lincoln Mercury dealer.


Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury. Do not modify the front end of the vehicle.


Additional equipment may affect the performance of the air bag sensors increasing the risk of injury. Please refer to the Body


Builders Layout Book for instructions about the appropriate installation of additional equipment.


120


Seating and safety restraints


Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.


Air bags can kill or injure a child in a child seat.


NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.


How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts unless the collision causes sufficient longitudinal deceleration.


121


Seating and safety restraints


The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying air bag may also cause abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control. The SRS consists of: • driver and passenger air bag modules (which include the inflators and • one or more impact and safing sensors • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.


air bags)


Several air bag system components get hot after inflation. Do not touch them after inflation.


122


Seating and safety restraints


If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not


replaced, the unrepaired area will increase the risk of injury in a collision.


Loading...
x