2008 Ford Escape Hybrid Owners Manual

Lights

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full Dome/ON position to reset. This will ensure that your displays are visible under all lighting conditions.

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized dealer.

ground

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4
meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens. 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover the left-hand headlamp with an opaque cloth. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge of high intensity light towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted.

49

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

5. Locate the vertical adjuster on the headlamp, then use a 4 mm socket to turn the adjuster either counterclockwise (to adjust up) or clockwise (to adjust down) aligning the upper edge of the light pattern to the horizontal line. 6. Move the opaque cloth to cover the right-hand headlamp and repeat Steps 4 and 5 for the left-hand headlamp. 7. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. 8. Close the hood and turn off the lamps. TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn

turn signal.

signal.

INTERIOR LAMPS

Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp control has three positions: • OFF: In this position, the lamp will not illuminate when the doors are open or when attempting to turn the dome lamp on by fully rotating the dimmer control located on the instrument panel.

• DOOR: In this position, the dome lamp will illuminate only when a door is opened and will remain illuminated for 25 seconds after the door is shut.

50

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

• ON: In this position, the lamp will remain illuminated. The map lamp controls (without moon roof) are located on the dome lamp. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps.

For models equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps. The map lamps will illuminate whenever a door is opened. After the door is shut, the lamps will remain illuminated for 25 seconds.

Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR

position and any door is open.

When the control is in the OFF position, it will not illuminate when you open the doors. Interior lighting battery saver The interior lamps will automatically extinguish after 10 minutes when the ignition key is in OFF/LOCK position, a door has been left open or the interior lamp controls are in the ON position.

51

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

BULB REPLACEMENT

Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation.

Trade number

Number of bulbs

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time. Function Headlamps (high and low beams) Park/turn lamps (front) Side marker (front) Rear stop/tail/sidemarker Backup lamp Fog lamp (front) Center High-mount stop lamp Rear license plate lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer

3157A (amber)

3157K / 4157K

PS24WFF

W5WL

H13

168

194

921

Replacing the interior bulbs Check the operation of all bulbs frequently.

Replacing exterior bulbs Check the operation of all the bulbs frequently.

52

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Reach over the front bolster. 4. Remove the bulb by turning it counterclockwise and then pulling it straight out.

5. Disconnect the electrical connector from the bulb.

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

6. Connect the electrical connector on the new bulb. 7. Insert the glass end of the new bulb into the headlamp assembly. When the grooves in the plastic base are aligned, turn the new bulb clockwise to install. Replacing front parking lamp/turn signal bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Reach over the front bolster. 4. Rotate the bulb socket counterclockwise and remove from the lamp assembly.

53

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

5. Carefully pull the bulb out of the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise.

Replacing front sidemarker bulbs For bulb replacement, see your authorized dealer. Replacing tail/stop/turn/sidemarker/backup lamp bulbs The tail/stop/turn/sidemarker/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Make sure the headlamp switch is in the OFF position and then open the liftgate to expose the lamp assembly screws. 2. Remove the two screws from the lamp assembly. 3. Carefully remove the lamp assembly away from the vehicle by pulling the assembly straight out to expose the bulb socket. DO NOT TIP THE LAMP ASSEMBLY SIDEWAYS. 4. Rotate the bulb socket counterclockwise and remove from lamp assembly. 5. Pull bulb straight out of socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle and secure with two screws.

54

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

55

Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Depress the lever and carefully pry the license plate lamp assembly (located above the license plate) from the liftgate. 3. Rotate the bulb socket counterclockwise and remove from lamp assembly. 4. Pull bulb straight out of socket and push in the new bulb. 5. Install the bulb socket into the lamp assembly and rotate clockwise. 6. To install, carefully press the lamp assembly into liftgate.

Replacing high-mount brake lamp bulbs To remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate.

2. Remove the bulb holder from the lamp assembly by depressing the snaps.

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Lights

3. Pull the bulb straight out of the socket and push in the new bulb. To complete installation, follow the removal procedure in reverse order.

Replacing fog lamp bulbs (if equipped) 1. Make sure the fog lamp switch is in the OFF position. 2. From underneath the vehicle, remove the harness/bulb assembly from the lamp assembly. 3. Carefully disconnect the bulb from the harness assembly via the two snap clips. Install the new bulb in reverse order.

56

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers

will swipe three times with washer fluid.

• a long push and hold: the wipers and washer fluid will be activated for

up to ten seconds.

Courtesy wipe feature: One extra wipe will happen a few seconds after washing the front window to clear any water that is dripping down from the top of the windshield caused by the washing. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluid level frequently. Do not operate the wipers when the windshield is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield, always use the windshield washer. In freezing weather, be sure the wiper blades are not frozen to the windshield before operating the wipers.

Windshield wiper features (if equipped with Autolamp feature) The exterior lamps will turn on with the ignition on, headlamp control in the Autolamp position and the windshield wipers are turned on (for a fixed period of time).

57

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — Normal speed operation of rear wiper. INT 1 — Intermittent operation of rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either From either position, the control will automatically return to the INT 2
or OFF position.

position.

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down the steering column tilt lever. 2. Move the steering wheel up or down until you find the desired location.

3. Push the steering column tilt lever up. This will lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is

moving.

58

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps.

CENTER CONSOLE Your vehicle is equipped with a variety of console features. These include: 1. Cupholders 2. Utility compartment console lid has a CD holder, a business card holder and two pen holders. The utility compartment has a removable bin with coin holder slots, a sliding tray, a cell phone holder and CD holders 3. Rear power point 4. Rear cupholders 5. Small storage trays

Use only soft cups in the cupholders. Hard objects can injure you in a collision.

59

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The tray and inside bin can be removed to open up space to fit a laptop computer, MP3 players, CDs or handbags. To remove, open the console lid and pull the bin straight up and out from the console housing.

The sliding tray and inside bin can be hooked on the side or rear of the console for extra storage.

AUXILIARY POWER POINT (12V) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.

60

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The auxiliary power point is located in the instrument panel. A second auxiliary power point is located on the rear side of the center console. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. To have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery. To prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is • do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods.

not running,

Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.

Power point (110 VAC) (if equipped) The 110 VAC power point outlet is used for powering electrical devices that require up to 150W. Exceeding the 150W limit will cause the power point to cut off the power temporarily to provide overload protection.

61

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: The 110 VAC power point is equipped with a safety cap and a safety twist tab. They both provide protection from inserting any object into the power point other than the 110 VAC electrical device plug. The safety cap should always be in a closed position whenever the power point outlet is not in use. The 110 VAC power point is located in the floor console in front of the gearshift. The power outlet is not designed for the following electric appliances; they may not work properly: • Cathode ray tube type televisions. • Motor loads, such as vacuum cleaners, electric saws and other electric • Measuring devices, which process precise data, such as medical • Other appliances requiring an extremely stable power supply:

power tools, compressor-driven refrigerators, etc.

equipment, measuring equipment, etc.

microcomputer-controlled electric blankets, touch sensor lamps, etc.

Do not keep electrical devices plugged in the power point whenever the device is not in use. It is not recommended to use any extension cord with the 110 VAC power point, since it will defeat the safety protection design provided by the cap and twist tab. It will also cause the power point to overload due to powering multiple devices that can reach beyond the 150W load limit. The power point can switch to a fault mode when it is overloaded, overheated, or shorted. For overloading and shorting conditions, unplug your device and turn the ignition key off then on. For an overheating condition, let the system cool off, then turn the ignition key off then on. The 110 VAC power point can provide power whenever the vehicle ignition is in the run position and the power point green indicator light located in the top left corner is turned on. Refer to the indicator light code below for the power point status.

62

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Indicator light Code

Green light is On — Power point is ready to supply power Green light is Off — Power point power supply is off. Ignition is not in

RUN position

Green light is blinking — Power point is in fault mode

POWER WINDOWS

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and pull the window switches to open and close windows. • Push down (to the first detent) • Pull up (to the first detent) and

and hold the switch to open.

hold the switch to close.

AUTO

Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviated by lowering a front window approximately two to three inches.

One touch down (AUTO) Allows the driver’s window to open fully without holding the control down. Push the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

63

Driver Controls

Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls (except for the driver’s) press the right side of the control. Press the left side to restore the window controls. Accessory delay With accessory delay, the window switches, moon roof (if equipped) and audio system may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror UP or DOWN and from SIDE to SIDE.

Do not adjust the mirror while the vehicle is in motion.

Automatic dimming rear view mirror (if equipped) Your vehicle may be equipped with an inside rear view mirror which has an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) (when the mirror is on) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the inside rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

64

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Electronic compass (if equipped) The compass heading is displayed as one of N, NE, E, SE, S, SW, W and NW in the center stack display. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass calibration adjustment. Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine.

23

15

14
13
12

4. From Setup menu, select the Update Zone function.

7 8 9 1011

5. Press and hold the RESET control for approximately 5 seconds until ZONE XX appears in the center stack display. 6. Continue to press the RESET control until the correct zone appears in the center stack display.

65

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

7. The direction will display after the RESET control is released. The zone is now updated.

Compass calibration adjustment Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2. To calibrate, press and hold the RESET control for approximately ten seconds until CAL appears. Release the control. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value. It may take up to five circles to complete calibration. 4. The compass is now calibrated.

EXTERIOR MIRRORS Power side view mirrors

Do not adjust the mirror while the vehicle is in motion.

To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

66

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Fold-away mirrors Fold the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

SPEED CONTROL With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

67

Driver Controls

3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator light instrument cluster will turn on.

on the

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

Disengaging speed control To disengage the speed control: • Depress the brake pedal Disengaging the speed control will not erase previous set speed. Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed.

68

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Increasing speed while using speed control There are three ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. • Press and release the SET + control to operate the Tap-Up function. Each tap will increase the set speed by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control There are three ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. • Press and release the SET -

control to operate the Tap-Down function. Each tap will decrease the set speed by 1 mph (1.6 km/h).

• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control.

69

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFF • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

control.

STEERING WHEEL CONTROLS

Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use steering wheel controls and other devices not essential to the driving task when it is safe to do so.

These controls allow you to operate some audio control features.

Radio control features Press MEDIA to select: • AM, FM1, FM2, or CD • LINE IN (Auxiliary input jack) (if

equipped)

70

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

In Radio mode: • Press

to access the

next/previous preset station.

In CD mode: • Press

to listen to the

next track on the disc.

In any mode: • Press VOL + or - to adjust the

volume.

MOON ROOF (IF EQUIPPED)

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

To operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control again.

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

71

Driver Controls • To close, press and hold the front portion of the control until the

moon roof comes to a complete stop then release the control.

To operate the moon roof vent position: • To open, press and hold the front portion of the control. This will • To close, press and hold the rear portion of the control until the moon

open the vent.

roof comes to a complete stop then release the control.

Note: If the battery is disconnected, discharged, or a new battery is installed, the moon roof needs to be opened to the vent position to reset the moon roof positions. If you open and close the moon roof repeatedly, the moon roof motor may overheat and shut down for 45 seconds while the motor cools.

MESSAGE CENTER With the ignition in the RUN position, the message center, located on your instrument cluster, displays important vehicle and daily driving information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by an indicator chime.

Selectable features

Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu.

72

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

equipped)

Info menu This control displays the following control displays: • Trip Odometer A or B • Distance to Empty • Average Fuel Economy (if • Instantaneous Fuel Economy (if equipped) • Electric Energy • Blank (odometer off) Note: If equipped with a Navigation Screen, the Average Fuel Economy and Instantaneous Fuel Economy will display in that screen instead of the message center display. Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu will give you an estimate of how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few miles (kilometers). DTE will vary according to your driving habits. Average fuel economy (AFE) (if equipped) Selecting this function from the INFO menu will display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing miles traveled by gallons of fuel used (liters of fuel by used 100 kilometers traveled), your figure may be different than displayed for the following reasons: • your vehicle was not perfectly level during fill-up • differences in the automatic shut-off points on the fuel pumps at

service stations

73

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls • variations in top-off procedure from one fill-up to another • rounding off the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. To reset back to zero, press and hold the RESET button for 2 seconds. Instantaneous fuel economy (if equipped) Select this function from the INFO menu to display your instantaneous fuel economy. This will display your fuel economy as a Bar Graph ranging from to Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows illuminated. Instantaneous fuel economy cannot be reset. Electric Energy Select this function from the INFO menu for the state of charge of the high voltage battery. For normal operation “ELECT ENERGY OK” will be displayed.

excellent economy.

poor economy

, one or no bars

language)

Setup menu Press this control for the following displays: • Reset to English (if in another • System Check • Oil Life • Units (English/Metric) • Autolamp Delay (if equipped) • Autolock (if equipped) 74

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

• Autounlock (if equipped) • Language Reset to English (if in another language) When entering the SETUP MENU and a non-English language has been selected, “PRESS RESET FOR ENGLISH” will be displayed to change back to English. Press the RESET control to change back to English. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for four seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. If you don’t press any button, the system will cycle itself. The sequence of the system check report is as follows: 1. Oil life 2. Electric drive 3. Brake system 4. Liftgate and glass 5. DTE/Fuel level Oil life An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change (approximately 10,000 miles [16,000 km] or 12 months) perform the following:

75

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Press and release the SETUP control to display “OIL LIFE = XXX% HOLD RESET = NEW”.

2. Press and hold the RESET control for 2 seconds and release. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed. 3. While “OIL LIFE SET TO 100%” is displayed, if a lower oil life start value is desired, press and release the RESET control to reduce the start value. Each press of the RESET control reduces the value by 10 percent. Note: Oil life start value of 100% equals 10,000 miles [16,000 km] or 12
months. For example, setting oil life start value to 60% sets the oil life start value to 6,000 miles (9,600 km) and 219 days. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change the message display from English to Metric. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds. Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion.

76

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolock ON or OFF. Autounlock This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off. 1. To disable/enable the autounlock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control switch to turn the autounlock ON or OFF. Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Waiting 4 seconds or pressing the RESET control cycles the message center through each of the language choices. Selectable languages are English, Spanish, or French. 3. Press and hold the RESET control for 2 seconds to set the language choice. System warnings/information System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message.

77

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Warning messages that have been reset are divided into two categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition LOCK-RUN cycle has been

completed if the fault condition still exists.

This acts as a reminder that these warning conditions still exist within the vehicle.

Warnings

Status Warning cannot be reset

Warning returns after 10 minutes if condition still exists

Warning returns after the ignition key is turned from OFF to RUN.

Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar Stop safely now High engine temperature High motor temperature Park brake engaged XXX miles (km) to empty fuel level low Liftgate/Glass ajar Service brake system Low brake fluid Regen brakes disabled Low tire pressure Tire pressure monitor fault Tire pressure sensor fault XX% oil life change soon Oil change required DRIVER DOOR AJAR. Displayed when the driver door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR. Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR. Displayed when the rear right door is not completely closed.

78

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

STOP SAFELY NOW. Displayed when the Master electrical hazard warning lamp is illuminated indicating a Hybrid component failure. If this warning occurs, the vehicle will soon shutdown without further warning, stop the vehicle as soon as safely possible and contact your authorized dealer as soon as possible. HIGH ENGINE TEMPERATURE. Displayed when the engine coolant is overheating. Engine coolant temperature warning lamp will illuminate indicating coolant temperature is high. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

When the engine and radiator are hot, scalding coolant and steam may shoot out under pressure and cause serious injury. Do not remove the cooling system cap when the engine and radiator are hot.

HIGH MOTOR TEMPERATURE. Displayed when the motor electronics are overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Refer to Engine coolant and motor/electronics coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. PARK BRAKE ENGAGED. Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km). If the warning stays on after the park brake is released, contact your authorized dealer as soon as possible. XXX MILES TO EMPTY FUEL LEVEL LOW. Displayed as an early reminder of a low fuel condition. LIFTGATE/GLASS AJAR. Displayed when the liftgate or liftgate glass is not completely closed. Press RESET to reset display. SERVICE BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW BRAKE FLUID. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. REGEN BRAKES DISABLED. Indicates the regenerative braking system is disabled at this moment. Please see your authorized dealer if this warning remains present over several days.

79

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating your tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Tire pressure monitoring system in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer XX% OIL LIFE CHANGE SOON/OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 10% or less. When oil life left is between 10% and 0%, the XX% OIL LIFE CHANGE SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed.

LIFTGATE • To open the liftgate window, unlock the liftgate (with the power door locks or the remote entry) and push the right side control button under the license plate lamp shield. • To open the liftgate, unlock the liftgate (with the power door locks or the remote entry) and push the middle control button under the license plate lamp shield.

To lock the liftgate and the liftgate window, use the power door locks. Do not open the liftgate or liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be damaged against a low ceiling. Do not leave the liftgate or liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.

80

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.

Exhaust fumes contain carbon monoxide which can injure your lungs and cause drowsiness and even death. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.

CARGO AREA FEATURES

Cargo shade (if equipped) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. To install the shade: • Insert the ends of the cargo

shade into the mounting features located behind the rear seat on the rear trim panels.

To operate the shade: 1. Grasp the rear edge of the cargo shade and pull rearward. 2. Secure both ends of the support rod into the retention slots located on the rear quarter trim panels.

Ensure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is

not securely installed.

Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of vehicle in the case of

a sudden stop or collision.

81

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

LUGGAGE RACK Your vehicle is equipped with a roof rack. The maximum load for the roof rack is 100 lb (44 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars as possible. Do not use the vehicle’s door handles as tie down loops. Use the tie-down loops on the thumbwheels to secure load. To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar. To remove the cross-bar assembly (if equipped) from the roof rack side rails: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable).

82

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

2. Slide the cross-bar to the end of the rail.

Driver Controls

3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar. 4. Slide the cross-bar assembly off the end of the rail.

To reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle. 2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar. 3. Slide the cross-bar assemblies over the end cap tongue and into the side rails.

83

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

4. Tighten thumbwheel at both ends of the cross-bar.

84

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS Your vehicle is equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter.

Your IKTs are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied IKTs, replacement IKTs are available through your authorized dealer. Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. Always carry a spare key with you in case of an emergency. For more information regarding programming replacement IKTs, refer to the SecuriLock™ passive anti-theft system section later in this chapter. Note: Your vehicle’s IKTs were issued with an adhesive security label on them that provides important vehicle key cut information. It is recommended that you maintain the label in a safe place for future reference, such as the inside front cover of this Owner’s Guide.

85

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Recommended handling of the Integrated Keyhead Transmitter (IKT) To avoid inadvertently activating the remote entry functions of your vehicle, it is recommended that the Integrated Keyhead Transmitter (IKT) be handled properly when starting and turning off your vehicle. When inserting the IKT into the ignition cylinder, place your thumb on the center thumb rest of the IKT and forefinger on the logo badge on the opposite side.

To gain more leverage when rotating the IKT in the ignition lock cylinder, you can readjust the location of your thumb to grasp the IKT on the control. outer edge next to the

Likewise, when rotating the IKT to the 1 (LOCK) position in the ignition lock cylinder, the bottom edge of the IKT adjacent to the control can be utilized.

86

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

POWER DOOR LOCKS • Press the • Press the

doors.

control to lock all

control to unlock all

doors.

Door key unlocking/locking Unlocking the doors Turn the key in the door cylinder to unlock the driver’s door only. All other doors will remain locked. Locking the doors Turn the key in the door cylinder to lock the driver’s door only.

Autolock The autolock feature will lock all the doors, liftgate and liftgate window when: • all doors are closed, • the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON) position and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Your vehicle comes with the autolock feature enabled. There are four methods to enable/disable this feature: • Through your authorized dealer, or • Performing the power door lock control procedure, or • Performing the keyless entry key pad (if equipped) procedure, or • Performing the message center (if equipped) procedure.

87

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is in the 1 (OFF/LOCK) position, and all vehicle doors, liftgate and liftgate window are closed. Power door unlock/lock procedure You must complete Steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. Note: All doors must be closed and remain closed throughout the configuration process. 1. The ignition must be off to begin sequence. 2. Turn the ignition to the 3 (ON) position. 3. Press the power door unlock control three times. 4. Turn the ignition from the 3 (ON) to the 1 (OFF/LOCK) position. 5. Press the power door unlock control three times. 6. Turn the ignition back to the 3 (ON) position. The horn will chirp. 7. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 8. Turn the ignition to the 1 (OFF/LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry key pad procedure 1. Turn the ignition to the 1 (OFF/LOCK) position. 2. Close all doors, the liftgate and liftgate window. 3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.

88

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Message center procedure For information on activating/deactivating the autolock feature using the vehicle’s message center (if equipped), refer to Message center information in the Driver Controls chapter.

Autounlock The autounlock feature will unlock all the doors when: • the ignition is in the 3 (RUN) position, all the doors are closed, and

the vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the 1
• the driver door is opened within 10 minutes of the ignition being

(OFF/LOCK) or 2 (ACC) position; and

transitioned to the 1 (LOCK) or 2 (ACC) position.

Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock Your vehicle comes with the autounlock feature activated. There are four methods to enable/disable this feature: • Through your authorized dealer, or • by using the power door unlock/lock sequence, • Performing the keyless entry key pad procedure (if equipped), or • by using the instrument cluster message center (if equipped). Refer to

Message center in the Driver Controls chapter.

Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30
seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the 3 (RUN) position.

89

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition to the 1 (LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry key pad autounlock enable/disable procedure 1. Turn the ignition to the 1 (LOCK) position. 2. Close all doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second time. 5. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. Message center procedure For information on activating/deactivating the autounlock feature using the vehicle’s message center (if equipped), refer to Message center information in the Driver Controls chapter.

Smart unlocking feature The smart unlocking feature helps prevent you from locking yourself out of the vehicle. With the key in any ignition position, the driver’s door will automatically unlock if it is locked using the power lock control on the driver’s door panel while the driver’s door is open.

90

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. NOTE: Setting the lock for one door will not automatically set the lock for both doors so you must set each child lock on each door separately. Insert the key and turn in the direction of arrow shown on the door to engage the child proof lock. Turn in the opposite direction to disengage childproof locks.

REMOTE ENTRY SYSTEM (IF EQUIPPED) The Integrated Keyhead Transmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

91

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

The typical operating range for your IKT is approximately 33 feet (10
meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to

your vehicle.

doors.

doors.

The IKT allows you to: • remotely unlock the vehicle • remotely lock all the vehicle • remotely open the power liftgate glass. • activate the personal alarm. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the 4 (START) position. The panic feature operates with the key in the 1 (LOCK) position. If there are problems with the remote entry system, make sure to take ALL Integrated Keyhead Transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Two step door unlocking 1. Press lamps will illuminate if the lamp is in the DOOR position. 2. Press passenger doors, the liftgate and liftgate glass. The battery saver feature will turn off the interior lamps 10 minutes after the ignition is turned to the 1 (OFF/LOCK) position. One step door unlocking If the one step door unlocking feature is activated, press and release once to unlock all of the doors, the liftgate and liftgate glass. Note: The interior lamps will illuminate (refer to Illuminated entry information later in this section), if the control on the overhead lamp is in the DOOR position.

and release to unlock the driver’s door. Note: The interior

and release again within three seconds to unlock the

92

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Switching from two step to one step door unlocking Unlocking can be switched between two step and one step door unlocking by pressing and holding both simultaneously on the remote entry transmitter for approximately 4
seconds. The turn signal will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two step unlocking.

buttons

and

and release to lock all the doors. Assuming all vehicle doors

Locking the doors 1. Press and the liftgate are properly closed and the park/turn lamps will flash once. and release again within three seconds to confirm that all 2. Press the doors and liftgate are closed and locked. Note: The doors will lock again and the horn will chirp once. If any of the doors or the hood are not properly closed, the horn will control is chirp twice and park/turn lamps will not flash when the pressed.

Opening the liftgate (if equipped) Press

twice within 3 seconds to open the liftgate glass.

Car finder twice within three seconds. The horn will chirp and the turn Press lamps will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.

to activate the alarm. To deactivate the feature, press the

Sounding a panic alarm Press control again, turn the ignition to the 3 (RUN) or 4 (START) position, or wait for the alarm to time out in approximately 3 minutes. Note: The panic alarm will only operate when the ignition is in the 1
(LOCK) position.

Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.

93

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

To replace the battery: 1. Twist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover.

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the instructions inside the IKT for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the battery cover back onto the key. Note: Replacement of the battery will not cause the IKT to become deprogrammed from your vehicle. The IKT should operate normally after battery replacement.

Replacing lost Integrated Keyhead Transmitters (IKTs) If you would like to have your Integrated Keyhead Transmitters reprogrammed because you lost one, or would like to buy additional IKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to reprogram your Integrated Keyhead Transmitters (IKTs) To program a new Integrated Keyhead Transmitter yourself, refer to Programming spare keys in the SecuriLock™ passive anti-theft section of this chapter. Note: At least two IKTs are required to perform this procedure yourself.

94

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead Transmitter or the keyless entry system keypad is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, or • the Integrated Keyhead Transmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad (if equipped), or • after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit • The interior lights will illuminate when the key is removed from the

ignition.

The lamps automatically turn off after 25 seconds. The dome and cargo lamp controls must not be set to the OFF position for the illuminated exit system to operate.

(unlock) control on the transmitter is pressed:

Perimeter lamps illuminated entry With the Integrated Keyhead Transmitter system, the following items will illuminate when the • Head lamps • Park lamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the IKT • after 25 seconds of illumination. Note: On some vehicles, the perimeter lamps illuminated entry feature will not activate in daylight conditions. Deactivating/activating perimeter lamps illuminated entry You may enable/disable this feature by having your vehicle serviced by your authorized dealer.

(lock) control is pressed, or

95

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. The ignition must be OFF to begin the sequence. 2. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 3. Press the power door unlock control on the door panel three times. 4. Turn the ignition from the 3
(RUN) position to the 1 (LOCK) position. 5. Press the power door unlock control on the door panel three times. 6. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 7. Press the power door unlock control twice within 5 seconds. Note: The horn will chirp once to indicate the perimeter lighting feature has been deactivated. The horn will chirp once and honk once (one short and one long) to indicate the perimeter lighting feature has been activated. 8. Turn the ignition to the 1 (LOCK) position to exit the procedure. Note: The horn will chirp once to confirm the procedure is complete.

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded Integrated Keyhead Transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded Integrated Keyhead Transmitters; additional coded IKTs may be purchased from your authorized dealer. Standard SecuriLock™ keys without remote entry transmitter functionality can also be purchased from your authorized dealer if desired. The authorized dealer can program your spare IKTs to your

96

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

vehicle or you can program the IKTs yourself. Refer to Programming spare Integrated Keyhead Transmitters for instructions on how to program the coded key. Note: The SecuriLock™ passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded IKT while starting the engine. These objects will not cause damage to the coded IKT, but may cause a momentary issue if they are too close to the IKT when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded IKT and restart the engine.

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the 1
(LOCK) position, the indicator will flash once every 2 seconds to indicate the SecuriLock™ system is functioning as a theft deterrent.

• When the ignition is in the 3 (RUN) position, the indicator will glow

for 3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock™ system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. If this occurs, the vehicle will not start and should be taken to an authorized dealer for service.

Automatic arming The vehicle is armed immediately after switching the ignition to the 1
(LOCK) position. The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed.

Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the 3
(RUN) position.

97

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

The theft indicator will illuminate for three seconds and then go out. If the theft indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your authorized dealer.

Replacement Integrated Keyless Transmitters (IKT) and coded keys Note: Your vehicle comes equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote keyless entry transmitter. A maximum of eight coded keys can be programmed to your vehicle; only four of these eight keys can be IKTs with remote entry functionality. If your IKTs or standard SecuriLock™ coded keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys You can program your own Integrated Keyhead Transmitters or standard SecuriLock™ coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry transmitter portion of the IKT to your vehicle. Note: A maximum of eight coded keys can be programmed to your vehicle; only four of these eight can be IKTs with remote entry functionality. Tips: • Only use Integrated Keyhead Transmitters (IKTs) or standard • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

• If two previously programmed coded keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.

SecuriLock™ keys.

98

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition.

2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds. 3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition. 4. Within ten seconds of turning the ignition to the 1 (LOCK) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds. 6. Turn the ignition to the 1 (LOCK) position and remove the second previously programmed coded key from the ignition. 7. Within twenty seconds of turning the ignition to the 1 (LOCK) position and removing the previously programmed coded key, insert the new unprogrammed key (new key/valet key) into the ignition. 8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least six seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and will operate the remote entry system (if the new key is an Integrated Keyhead Transmitter). The theft indicator light will illuminate for three seconds and then go out to indicate successful programming. If the key was not successfully programmed, it will not start your vehicle’s engine and/or will not operate the remote entry features. The theft indicator light may flash on and off. Wait 20 seconds and you may repeat Steps 1 through 8. If failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), wait twenty seconds and then repeat this procedure from Step 1.

99

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

FRONT SEATS Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.

After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Adjustable head restraints

To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate

the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion.

The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down.

100

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Push side control and push down on head restraint to lower it.

Adjusting the front manual seat (if equipped) Lift handle to move seat forward or backward.

Pull lever up to adjust seatback.

101

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Adjusting the front power seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.

To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if

equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system section for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.

The control is located on the outboard side of the seat cushion.

102

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Press to raise or lower the front portion of the seat cushion.

Press to raise or lower the rear portion of the seat cushion.

Press the control to move the seat forward, backward, up or down.

Heated seats (if equipped)

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury,

medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

103

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the

seat. Allow the seat to dry thoroughly.

To operate the heated seats: • Push the button located on the • Push again to deactivate.

instrument panel to activate.

The heated seats will activate when the ignition is in the RUN position. The system automatically shuts off after 10 minutes.

REAR SEATS

Head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head.

104

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Push control to lower or remove head restraint.

Folding down rear seats 1. Raise the rear seat head restraint and remove.

2. Place the head restraint under the front seat for storage.

3. Pull the seat release control.

Note: Make sure the floor is clear of all objects before folding the seat.

105

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

4. Flip seat forward.

Attach the safety belt web snap button to the quarter trim panel snap button. This will ensure that safety belt does not get caught by staying out of the seat back folding path.

5. To release seatback, pull the seatback release lever (on top of seat) toward the front seat. This is common for both 60% and 40% seatbacks. Note: When the seatback release lever is pulled, slowly lower seatback to the flat position.

106

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

6. Rotate seatback down into load floor position.

Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place and the red seat unlatched indicator on release paddle is not visible.

2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the safety belt buckles are exposed.

Make sure safety belt buckle heads are through elastic

holders on seat backs. Safety belt buckles may break if they are trapped underneath the seatback as the seatback is rotated down.

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

107

Seating and Safety Restraints

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, reinstall the head restraints, and pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Remove the head restraint stored under the front set

and return it to the original position on the seatback. Failure to do so could result in personal injury.

3. Unsnap the safety belt webbing from the quarter trim panel. To remove the rear cushion 1. Lift the yellow tab to release the hinges. 2. Pull the cushion to the outboard side of the vehicle.

108

2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt)