2007 Ford Escape Hybrid Owners Manual

front of the vehicle. 2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar. 3. Slide the cross-bar assemblies over the end cap tongue and into the side rails. 4. Tighten thumbwheel at both ends of the cross-bar.

108

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS One key operates all locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer. Refer to the SecuriLock娂 passive anti-theft system section in this chapter for more information.

POWER DOOR LOCKS The power door lock controls are located on the driver and front passenger door panels. Pressing the doors. Pressing the the doors.

will unlock all the will lock all

Power door lock/unlock inhibit feature As a theft deterrent, the power door lock controls can be disabled 20
seconds after the ignition has been turned to the 1 (LOCK) position and the vehicle is locked using the remote entry transmitter or the key in the door lock cylinder. The door lock controls are enabled when the vehicle is unlocked using the key in the door lock cylinder or by pressing on the remote entry transmitter. This feature can be turned on or off using the following procedure: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. 1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. Press the power door lock control on the door panel two times within five seconds. The horn will chirp two times to confirm the feature is off; the horn will chirp two times and honk one time to confirm the feature is on.

109

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

7. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off.

Door key unlocking/locking Two step door unlocking 1. Turn the key in the door cylinder to unlock the driver’s door. Note: The interior lamps will illuminate if the control on the overhead lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate. For more information, refer to Illuminated entry later in this chapter. 2. Turn the key in the door cylinder again within three seconds to unlock the passenger doors, the liftgate and liftgate glass. One step door unlocking If the one step door unlocking feature is activated, turn the key in the door cylinder once to unlock all of the doors , the liftgate and liftgate glass. Note: The interior lamps will illuminate (refer to the Illuminated entry feature later in this section), if the control on the overhead lamp is in the DOOR position. For information on switching from two step to one step door unlocking, refer to Switching from two step to one step door unlocking later in this chapter. Locking the doors Turn the key in the door cylinder to lock all the doors. The park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. If any of the doors, the liftgate or the hood are not properly closed the park/turn lamps will not flash.

Autolock (if equipped) The autolock feature automatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (RUN) position, • the brake has been released, and • the vehicle has been set in motion.

110

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

closed, and

Relock This feature will also automatically relock all the doors when: • the ignition is in the 3 (RUN) position and any door is opened then • you put the vehicle in motion by releasing the brake pedal. Deactivating/activating the autolock feature The autolock feature can be activated or deactivated using the following procedure: Before starting, make sure that the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. 1. Turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control three times. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. 6. The horn will chirp once to confirm programming mode is entered/active. 7. Press the power door unlock control on the door panel one time. 8. Press the power door lock control on the door panel one time. Note: The horn will chirp once to confirm the feature is OFF, or the horn will chirp and then honk to confirm the feature is ON. 9. Turn the ignition to the 1 (LOCK) position. Note: The horn will chirp once to confirm the programming mode has been exited. Repeat the previous procedure to turn the feature on or off.

Smart unlocking feature The smart unlocking feature helps prevent you from locking yourself out of the vehicle. With the key in any ignition position, the driver’s door will automatically unlock if it is locked using the power lock control on the driver’s door panel while the driver’s door is open.

111

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS • When these locks are set, the

rear doors cannot be opened from the inside.

• The rear doors can be opened

from the outside when the doors are unlocked.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Rotate lock control in the

direction of arrow to engage the lock.

• Rotate control in the opposite

direction to disengage childproof locks.

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. 112

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote locking and unlocking features will operate independent of the ignition position; however, the panic feature will only operate when the ignition is in the 1
(LOCK) or 2 (ACCESSORY) position. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.

and release again within three seconds to unlock the

and release to unlock the driver’s door. Note: The interior

Two step door unlocking 1. Press lamps will illuminate if the lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate. 2. Press passenger doors, the liftgate and liftgate glass. One step door unlocking and release If the one step door unlocking feature is activated, press once to unlock all of the doors , the liftgate and liftgate glass. Note: The interior lamps will illuminate (refer to Illuminated entry information later in this section), if the control on the overhead lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate. Switching from two step to one step door unlocking Unlocking can be switched between two step and one step door unlocking by pressing and holding both simultaneously on the remote entry transmitter for approximately 4
seconds. The parklamps will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two step unlocking.

buttons

and

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps lamps will flash once and the perimeter alarm (if equipped) will start the arming process.

113

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. and release again within three seconds to confirm that all 2. Press the doors and liftgate are closed and locked. Note: The doors will lock again and the horn will chirp once. If any of the doors or the hood are not properly closed, the horn will control is chirp twice and park/turn lamps will not flash when the pressed.

to activate the alarm. To deactivate the feature, press the

Sounding a panic alarm Press control again, turn the ignition to the 3 (RUN) or 4 (START) position, or wait for the alarm to time out in approximately 3 minutes. Note: The panic alarm will only operate when the ignition is in the 1
(LOCK) position.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

114

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle.

115

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Note: Ensure the brake pedal is not depressed during this sequence. To reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed. 8. Repeat Step 6 to program each additional remote entry transmitter. 9. Turn the ignition to the 1 (LOCK) position after you have finished programming all of the remote entry transmitters. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 2 (ACCESSORY) position, or • the remote transmitter lock control is pressed, or • the doors are locked by key in the door cylinder, or 116

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• after 25 seconds of illumination. Illuminated exit • The interior lights will illuminate when the key is removed from the

ignition.

The lamps automatically turn off after 25 seconds. The dome and cargo lamp controls must not be set to the OFF position for the illuminated exit system to operate.

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer. The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.

Anti-theft indicator The anti-theft indicator is located in the instrument cluster. • When the ignition is in the 1 (LOCK) position, the anti-theft indicator will flash once every 2 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent. • When the ignition is in the 3 (RUN) position, the anti-theft indicator

will glow for 3 seconds, then turn off to indicate normal system functionality.

117

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. If this occurs, the vehicle should be taken to an authorized dealer for service.

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys You can program your own coded keys to your vehicle. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock娂 keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

• If two previously programmed coded keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.

Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. Turn the ignition from the 1
(LOCK) position to the 3 (RUN) position. Keep the ignition in the 3
(RUN) position for at least three seconds, but no more than 10
seconds. 3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition.

118

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

4. Within ten seconds of turning the ignition to the 1 (LOCK) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds. 6. Turn the ignition to the 1 (LOCK) position and remove the second previously programmed coded key from the ignition. 7. Within twenty seconds of turning the ignition to the 1 (LOCK) position and removing the previously programmed coded key, insert the new unprogrammed key (new key/valet key) into the ignition. 8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds but not more than 10 seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off; you may need to repeat Steps 1 through 5. If failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), wait twenty seconds and then repeat this procedure from Step 1.

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting.

Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the park/turn lamps and will sound the horn. The system is ready to arm whenever the key is removed from the ignition. Any of the following actions will prearm the alarm system: • Press the

control on the remote entry transmitter.

119

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security • Lock the doors with the key in the key cylinder. • Open the driver’s door and press the power door lock control to lock

all the doors, and then close the door.

Note: The doors, liftgate and hood will arm individually, and if any of them are open, they must be closed in order to be armed. When you lock the vehicle using any of the methods above: • the park/turn lamps will flash once to indicate the hood, each door • the park/turn lamps will not flash if the hood, any door or the liftgate are open. Once all doors, hood and liftgate are closed, the park/turn lamps will flash to confirm the alarm will be set.

and the liftgate are closed.

When the vehicle is locked, the alarm is set after a 20–second arming period. When you press the within three seconds, the horn will chirp once to confirm the doors, liftgate and hood are closed and locked, and the alarm is set.

control on the remote entry transmitter twice

transmitter.

control on your remote entry

of the vehicle) to ensure the alarm disarms.

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the • Unlock the doors with a key. Turn the key full travel (toward the front • Turning the key in the ignition to the 3 (RUN) or 4 (START) position. Triggering the anti-theft system The armed system will be triggered if any door, liftgate or the hood is opened without using the key or the remote entry transmitter. To deactivate the triggered alarm state: • Unlock the doors by pressing the • Unlock the doors with a key. Turn the key full travel (toward the front • Press on the remote entry transmitter to disable the alarm; the alarm will be disabled, but the vehicle will remain in an armed state. • Turning the key in the ignition to the 3 (RUN) or 4 (START) position. 120

of the vehicle) to ensure the alarm disarms.

control on your remote entry

transmitter.

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

FRONT SEATS Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.

After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Adjustable head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down.

121

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Push side control and push down on head restraint to lower it.

Adjusting the front manual seat (if equipped) Lift handle to move seat forward or backward.

Pull lever up to adjust seatback.

Adjusting the front power seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

122

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.

To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if

equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system section for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.

The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion.

123

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Press to raise or lower the rear portion of the seat cushion.

Press the control to move the seat forward, backward, up or down.

Heated seats (if equipped) To operate the heated seats: • Push the control located on the • Push again to deactivate.

seat to activate.

The heated seats will activate when the ignition is in the RUN position.

REAR SEATS

Head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.

124

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head.

Push control to lower or remove head restraint.

Folding down rear seats 1. Raise the rear seat head restraint and remove.

2. Place the head restraint under the front seat for storage.

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

125

Seating and Safety Restraints

3. Pull the seat release control.

Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward.

Attach the safety belt web snap button to the quarter trim panel snap button. This will ensure that safety belt does not get caught by staying out of the seat back folding path.

126

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

5. To release seatback, pull the seatback release lever (on top of seat) toward the front seat. This is common for both 60% and 40% seatbacks. Note: When the seatback release lever is pulled, slowly lower seatback to the flat position.

6. Rotate seatback down into load floor position.

Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place and the red seat unlatched indicator on release paddle is not visible.

127

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the safety belt buckles are exposed.

Make sure safety belt buckle heads are through elastic

holders on seat backs. Safety belt buckles may break if they are trapped underneath the seatback as the seatback is rotated down.

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, reinstall the head restraints, and pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Remove the head restraint stored under the front set

and return it to the original position on the seatback. Failure to do so could result in personal injury.

3. Unsnap the safety belt webbing from the quarter trim panel.

128

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

To remove the rear cushion 1. Lift the yellow tab to release the hinges. 2. Pull the cushion to the outboard side of the vehicle.

To install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place.

SAFETY RESTRAINTS

Personal Safety System姟 The Personal Safety System娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. Your vehicle’s Personal Safety System娂 consists of: • Driver and passenger dual-stage airbag supplemental restraints • Front safety belts with pretensioners, energy management retractors, • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp

and safety belt usage sensors

129

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints • Front crash severity sensor • Restraints Control Module (RCM) with impact and safing sensors • Driver’s seat position sensor • Restraint system warning light and back-up tone • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system, and indicator lights

How does the Personal Safety System姟 work? The Personal Safety System娂 can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions. The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system. Rather, it means the Personal Safety System娂 determined the accident conditions (crash severity, belt usage, etc.) were not appropriate to activate these safety devices. Front airbags are designed to activate only in frontal and near-frontal collisions, not rollovers, side-impacts, or rear-impacts unless the collision causes sufficient longitudinal deceleration. The driver’s side only is equipped with dual pretensioners. Dual-stage airbag supplemental restraints The dual-stage airbag offers the capability to tailor the level of airbag inflation energy. A lower, less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag supplemental restraints section in this chapter. Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact. This allows your Safety System to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage airbag and safety belt pretensioners.

130

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The driver’s side only is equipped with dual pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Safety System to tailor the deployment level of the driver airbag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front.

Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

The front passenger sensing system can automatically turn off the passenger front airbag. The system is designed to help protect small (child size) occupants from airbag deployments when they are improperly seated or restrained in the front passenger seat contrary to proper child-seating or restraint usage recommendations. Even with this technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag (if equipped) when the passenger seat is empty to prevent unnecessary replacement of airbag(s) after a collision. When the front passenger seat is occupied and the sensing system has turned off the passenger’s frontal airbag, the “pass airbag off” indicator

131

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

will light and stay lit to remind you that the front passenger frontal airbag is off. See Front passenger sensing system in the airbags section of this chapter. Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Safety System to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter. Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the Safety Canopy娂 system. This helps increase the effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can be activated alone or, if the collision is of sufficient severity, together with the front airbags. Front safety belt energy management retractors The front outboard safety belt energy management retractors, once initiated, allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum. This helps reduce the risk of force-related injuries to the occupant’s chest by limiting the load on the occupant. Refer to Energy management feature section in this chapter. The driver’s side only is equipped with dual pretensioners. Determining if the Personal Safety System is operational The Safety System uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the Safety System is not required. The Restraints control module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, driver seat position sensor, and front passenger sensing system. In addition, the RCM also monitors the restraints warning light in the instrument cluster. A difficulty with the system is indicated by one or more of the following. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition is

turned on.

132

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

• A series of five beeps will be heard. The tone pattern will repeat

periodically until the problem and warning light are repaired.

If any of these things happen, even intermittently, have the Safety System serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an airbag

supplemental restraint system (SRS) is provided.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas

are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that

are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

133

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check

seat covers and buckles before you place a child anywhere near them.

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

2. To unfasten, push the release button and remove the tongue from the buckle.

Energy Management Feature • This vehicle has a safety belt system with an energy management

feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • The front outboard safety belt system has a retractor assembly that is

designed to extend the safety belt webbing in a controlled manner. This helps reduce the belt force acting on the user’s chest.

All safety belts in the vehicle are combination lap and shoulder belts. The passenger safety belts have two types of locking modes described below:

134

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8
km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.

Automatic locking mode

When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter. How to use the automatic locking mode • Buckle the combination lap and

shoulder belt.

135

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is pulled out.

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which doesn’t have this feature) must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.

136

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Safety belt height adjustment Your vehicle has safety belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, squeeze and hold the buttons on the side and slide the height adjuster up or down. Release the buttons and pull down on the height adjuster to make sure it is locked in place.

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety

belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions. The safety belt pretensioners activate during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the optional Safety Canopy娂 system. A safety belt pretensioner is a device which tightens the webbing of the lap and shoulder belts in such a way that they fit more snugly against the body.

The driver and front passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the

vehicle is involved in a collision that results in deployment of front airbags, seat-mounted side airbags and Safety Canopy娂 (if equipped), and safety belt pretensioners.

Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of

a collision.

137

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch (20
cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.

Do not use extensions to change the fit of the shoulder belt across the torso.

Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe

personal injuries in the event of a collision.

For proper care of soiled safety belts, refer to Interior in the Cleaning chapter.

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.

138

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...

Then... The safety belt warning light illuminates 1 minute and the warning chime sounds 6 seconds.

The safety belt warning light and warning chime turn off.

The safety belt warning light and indicator chime remain off.

BeltMinder姞 The BeltMinder威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster when the driver’s and front passenger’s safety belt is unbuckled. The BeltMinder威 feature uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the BeltMinder威 feature for objects placed in the front passenger seat, warnings will only be given to large front seat occupants as determined by the front passenger sensing system. Both the driver’s and passenger’s safety belt usages are monitored and either may activate the BeltMinder威 feature. The warnings are the same for the driver and the front passenger. If the BeltMinder威 warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the BeltMinder威 feature.

139

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Then... The BeltMinder威 feature will not activate.

If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 5 km/h (3 mph) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...

The BeltMinder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until the safety belts are buckled. The BeltMinder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until the safety belts are buckled.

The driver’s or front passenger’s safety belt becomes unbuckled for approximately 1 minute while the vehicle is traveling at least 5 km/h (3 mph) and more than 1-2
minutes have elapsed since the ignition switch has been turned to ON... The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider... ⬙Crashes are rare events⬙

36700 crashes occur every day. The more we drive, the more we are exposed to ⬙rare⬙ events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime.

⬙I’m not going far⬙ 3 of 4 fatal crashes occur within 25 miles of home.

140

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Reasons given... Consider... ⬙Belts are uncomfortable⬙

Your Ford safety belts are designed to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.

⬙I was in a hurry⬙ Prime time for an accident. BeltMinder威

⬙Safety belts don’t work⬙

⬙Traffic is light⬙

⬙Belts wrinkle my clothes⬙

⬙The people I’m with don’t wear belts⬙

reminds us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.

⬙I’d rather be thrown clear⬙

⬙I have an airbag⬙ Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40
times more likely to DIE. Safety belts help prevent ejection, WE CAN’T ⬙PICK OUR CRASH⬙. Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the BeltMinder威 chime. To do so may

adversely affect the performance of the vehicle’s air bag system

One time disable If at any time the driver/front passenger quickly buckles then unbuckles the safety belt for that seating position, the BeltMinder威 is disabled for the current ignition cycle. The BeltMinder威 feature will enable during the same ignition cycle if the occupant buckles and remains buckled for approximately 30 seconds. Confirmation is not given for the one time disable.

141

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Deactivating/activating the BeltMinder姞 feature The driver and front passenger BeltMinder威 are deactivated/activated independently. When deactivating/activating one seating position, do not buckle the other position as this will terminate the process. Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. The driver and front passenger BeltMinder威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled

While the design allows you to deactivate your BeltMinder威, this system is designed to improve your chances of being safely

belted and surviving an accident. We recommend you leave the BeltMinder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the BeltMinder威 feature while driving the vehicle.

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1
minute) • Step 3 must be completed within 50 seconds after the safety belt

warning light turns off.

3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.) • After Step 3, the restraint system warning light (airbag light) will be

turned on for three seconds.

4. Within 10 seconds of the light turning on, at a moderate speed, buckle then unbuckle the safety belt. • This will disable the BeltMinder威 feature for that seating position if it

is currently enabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds.

142

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints • This will enable the BeltMinder威 feature for that seating position if it is currently disabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds, followed by 3
seconds with the light off, then followed by the restraint system warning light flashing 4 times per second for 3 seconds again.

• After receiving confirmation, the deactivation/activation procedure is

complete.

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

143

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

The National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm)

between an occupant’s chest and the driver airbag module.

Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries.

To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the • Recline the seat slightly one or two degrees from the upright position.

pedals comfortably.

Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those

objects to be propelled by the airbag into your face and torso causing serious injury.

Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. See your authorized

dealer.

Modifications to the front end of the vehicle, including frame, bumper, front end body structure, tow hooks and B-pillar

surrounding parts may affect the performance of the airbag sensors increasing the risk of injury. Do not modify the front end of the vehicle.

Additional equipment may affect the performance of the airbag sensors increasing the risk of injury. Please refer to the Body

Builders Layout Book for instructions about the appropriate installation of additional equipment.

144

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.

Airbags can kill or injure a child in a child seat.

NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the airbag sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not sufficient enough to cause activation. Front airbags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts unless the collision causes sufficient longitudinal deceleration.

145

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions, swelling or temporary hearing loss. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. It is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. The SRS consists of: • driver and passenger airbag modules (which include the inflators and • seat-mounted side airbags (if equipped). Refer to Seat-mounted side • Safety Canopy娂 system (if equipped). Refer to Safety Canopy娂 • one or more impact and safing sensors. • Safety belt pretensioners • a readiness light and tone. • diagnostic module. • and the electrical wiring which connects the components. • Front passenger sensing system. Refer to Front passenger sensing • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to

airbag system later in this chapter

system. later in this chapter.

system later in this chapter.

airbags).

Front passenger sensing system later in this chapter.

The RCM (restraints control module) monitors its own internal circuits and the supplemental airbag electrical system wiring (including the

146

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

impact sensors, the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors).

Several air bag system components get hot after inflation. Do not touch them after inflation.

If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.

Front passenger sensing system The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor Vehicle Safety Standard (FMVSS) 208
and is designed to disable (will not inflate) the front passenger’s frontal airbag under certain conditions. The front passenger sensing system works with sensors that are part of the front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or disabled (will not inflate). The front passenger sensing system will disable (will not inflate) the front passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in • the system determines that an infant is present in a rear-facing infant • the system determines that a small child is present in a forward-facing

seat that is installed according to the manufacturer’s instructions,

the front seat,

child restraint that is installed according to the manufacturer’s instructions,

• the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period of

time,

For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled.

147

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The front passenger sensing system uses a ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is off. The indicator lamp is located in the center stack of the instrument panel just below the radio. Note: The indicator lamp will illuminate for a short period of time when the ignition is turned to the ON position to confirm it is functional. When the front passenger seat is not occupied (empty seat) or in the event that the front passenger frontal airbag is enabled (may inflate), the indicator lamp will be unlit. The front passenger sensing system is designed to disable (will not inflate) the front passenger’s frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the indicator lamp will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. • If the child restraint has been installed and the indicator lamp is not

lit, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer’s instructions.

The front passenger sensing system is designed to enable (may inflate) the front passenger’s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat. • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’s seat, but the ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the • Have the person sit upright in the seat, centered on the seat cushion, • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag.

with the person’s legs comfortably extended.

full upright position.

148

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints • If the indicator lamp remains lit even after this, the person should be

advised to ride in the rear seat.

Occupant

Empty seat Small child in child safety seat or booster Small child with safety belt buckled or unbuckled Adult

Pass Airbag Off Indicator Lamp Unlit Lit

Lit

Unlit

Passenger Airbag

Disabled Disabled

Disabled

Enabled

Even with Advanced Restraints Systems, children 12 and under should be properly restrained in the back seat.

After all occupants have adjusted their seats and put on safety belts, it’s very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.

Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the

decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.

The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below.

149

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Pass Airbag Off Indicator Lamp Unlit

Objects

Passenger Airbag

Lit

Lit

Disabled

Disabled

Disabled

Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e. heavy briefcase, fully packed luggage) Empty seat, or small to medium object with safety belt buckled If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • Objects lodged underneath the seat • Objects between the seat cushion and the center console (if • Objects hanging off the seat back • Objects stowed in the seatback map pocket (if equipped) • Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above.

equipped)

To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or

hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag Status. Failure to follow these instructions may interfere with the front passenger seat sensing system.

150

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If objects are lodged and/or cargo is interfering with the seat; please take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver and/or adult passengers should check for any objects lodged • Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least 2 minutes and verify that the airbag readiness lamp is no • If the airbag readiness lamp remains illuminated, this may or may/not

underneath the front passenger seat or cargo interfering with the seat.

longer illuminated

be a problem due to the front passenger sensing system.

DO NOT attempt to repair or service the system; take your vehicle immediately to an authorized dealer. If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance chapter of this Owner’s Guide.

Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system.

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the status of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required.

151

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

flash or stay lit.

A difficulty with the system is indicated by one or more of the following: • The readiness light will either • The readiness light will not illuminate immediately after ignition is turned on.

• A series of five beeps will be heard. The tone pattern will repeat

periodically until the problem and/or light are repaired.

If any of these things happen, even intermittently, have the SRS serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.

Seat-mounted side airbag system (if equipped)

Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.

Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and

increase the risk of injury in an accident.

Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback.

Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See an

authorized dealer.

All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.

152

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. The side airbag system consists of the following: • An inflatable nylon bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.

• A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnostic unit as used • Two crash sensors located on the lower portion of the b-pillar (one on

for the front airbags.

each side of the vehicle).

Side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. If the front passenger sensing system detects an empty seat, the front passenger seat-mounted side airbag will be deactivated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side airbags are designed

153

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration.

Several airbag system components get hot after inflation. Do not touch them after inflation.

If the side airbag has deployed, the airbag will

not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either • The readiness light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat

flash or stay lit.

turned on.

periodically until the problem and/or light are repaired.

If any of these things happen, even intermittently, have the SRS serviced at your authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.

154

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Safety Canopy姟 system (if equipped)

Do not place objects or mount equipment on or

near the headliner at the siderail that may come into contact with a deploying Safety Canopy娂. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.

Do not lean your head on the door. The Safety Canopy娂 could injure you as it deploys from the headliner.

Do not attempt to service, repair, or modify the Safety Canopy娂 system, its fuses, the A, B, or C pillar trim, or the headliner on a

vehicle containing a Safety Canopy娂. See your authorized dealer.

All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety

Canopy娂 system is provided.

To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy娂.

155

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

How does the Safety Canopy姟 system work? The design and development of the Safety Canopy娂 system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy娂). The Safety Canopy娂 system consists of the following: • An inflatable nylon curtain with a gas generator concealed behind the headliner and above the doors (one on each side of vehicle). • A headliner designed to flex open • The same warning light, electronic control and diagnostic unit as used • Two crash sensors mounted at lower B-Pillar (one on each side). • Two crash sensors located at the c-pillar behind the rear doors (one • Rollover sensor in the restraints control module (RCM). The Safety Canopy娂 system, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision or rollover event. Children 12 years old and under should always be properly restrained in the second or third row seats. The Safety Canopy娂 will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The Safety Canopy娂 system is designed to active when the vehicle sustains lateral deceleration sufficient to cause the RCM to initiate Safety Canopy娂 inflation or when a certain likelihood of a rollover event is detected by the rollover sensor.

above the side doors to allow Safety Canopy娂 deployment.

for the front airbags.

on each side).

156

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The Safety Canopy娂 is mounted to roof side-rail sheet metal, behind the headliner, above the first and second row seats. The Safety Canopy娂 is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events. The fact that the Safety Canopy娂 did not activate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. The Safety Canopy娂 is designed to inflate in certain side impact collisions or rollover events, not in rear impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration or rollover likelihood.

Several Safety Canopy娂 system components get hot after inflation. Do not touch them after inflation.

If the Safety Canopy娂 system has deployed, the

Safety Canopy娂 will not function again unless replaced. The Safety Canopy娂 system (including the A, B and C pillar trim) must be inspected and serviced by a authorized dealer. If the Safety Canopy娂 is not replaced, the unrepaired area will increase the risk of injury in a collision.

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required.

157

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

flash or stay lit.

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either • The readiness light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat

turned on.

periodically until the problem and/or light are repaired.

If any of these things happen, even intermittently, have the SRS serviced at your authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.

Disposal of airbags and airbag equipped vehicles (including pretensioners) See your authorized dealer. Airbags MUST BE disposed of by qualified personnel.

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags.

Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children. Many states require that children use approved booster seats until they are eight years old. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle. When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

Always follow the instructions and warnings that come with any infant or child restraint you might use.

158

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.

Do not leave children, unreliable adults, or pets unattended in your vehicle.

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury in a crash. To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably. Booster seats may also make the shoulder belt fit better and more comfortably. Try to keep the belt near the middle of the shoulder. When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lb. (36 kg) (about 8 to 12 years old). Booster seats should be used until you can answer YES to ALL of these questions:

159

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching?

• Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless.

If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top of ear level) above the top of the seat. In this case, move the backless booster to another seating position with a higher seat back and lap/shoulder belts.

• Those with a high back.

If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice.

Either type can be used at any seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg).

160

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.

If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.

The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride.

Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use.

Follow all instructions provided by the manufacturer of the booster seat.

Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of

the body and may increase the risk of injury or death in a collision.

161

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a

collision.

SAFETY SEATS FOR CHILDREN

Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. When installing a child safety seat: • Review and follow the information

presented in the airbag supplemental restraint system (SRS) section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).

• Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic

locking mode (passenger side front and outboard rear seating positions) (if equipped) section in this chapter.

• LATCH lower anchors are recommended for use by children up to 48
lb. (22 kg) in a child restraint. Top tether anchors can be used for children up to 60 lb. (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 lb. (36 kg) using an upper torso harness and a belt-positioning booster.

Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LATCH and

162

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter.

Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.

Rear-facing child seats or infant carriers should never be placed in front of an active passenger airbag.

Installing child safety seats with combination lap and shoulder belts The rear seat head restraints must be removed when using a child seat.

Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must

use a forward-facing child seat in the front seat, move the seat all the way back.

1. Position the child safety seat in a seat with a combination lap and shoulder belt.

Children 12 and under should be properly restrained in the rear seat whenever possible.

163

2007 Escape Hybrid (ehv) Owners Guide (post-2002-fmt)