Login- Download PDF Manual
-
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle’s stopping distance. The ABS will be activated immediately, allowing you to retain steering control during hard braking and on slippery surfaces. However, the ABS does not decrease stopping distance. ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate during start up, remains on or flashes, the ABS may be disabled and may need to be serviced. Even when the ABS is disabled, normal braking is still effective. If your BRAKE warning lamp illuminates with the parking brake released, have your brake system serviced immediately by an authorized dealer.
BRAKE
ABS
Parking brake To set the parking brake (1), press the parking brake pedal down until the pedal stops. To release, pull the lever (2).
WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released.
BRAKE
199
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
TRACTION CONTROL™ (IF EQUIPPED) Your vehicle may be equipped with a Traction Control™ system. This system helps you maintain the stability and steerability of your vehicle, especially on slippery road surfaces such as snow- or ice-covered roads and gravel roads. The system will allow your vehicle to make better use of available traction in these conditions. During Traction Control™ operation, the traction control active light will flash and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior and should be no reason for concern.
WARNING: Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe
personal injury or property damage. The occurrence of a Traction Control™ event is an indication that at least some of the tires have exceeded their ability to grip the road; this may lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. If you experience a severe road event, SLOW DOWN.
The Traction Control™ switch, located on the center console, has an indicator light that illuminates steadily in the instrument cluster when the system is off. The Traction Control™ system will automatically turn on every time the ignition is turned off and on. The Traction Control™ system should normally be left on. If you should become stuck in snow or ice or on a very slippery road surface, try switching the Traction Control™ system off. This may allow excess wheel spin to “dig” the vehicle out and enable a successful “rocking” maneuver. Remember to switch the Traction Control™ system back on once the vehicle is no longer stuck.
200
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
If a system fault is detected, the traction control active light will illuminate steadily in the instrument cluster, the Traction Control™ button will not turn the system on or off and your vehicle should be serviced by an authorized dealer.
ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞) STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED)
WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire
construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceTrac威 with RSC威 system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac威 with RSC威 system. Install any aftermarket stereo loudspeaker as far as possible from the front center console, the tunnel, and the front seats in order to minimize the risk of interfering with the AdvanceTrac威 with RSC威 sensors. Reducing the effectiveness of the AdvanceTrac威 with RSC威 system could lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
WARNING: Remember that even advanced technology cannot defy the laws of physics. It’s always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage. Activation of the AdvanceTrac威 with RSC威 system is an indication that at least some of the tires have exceeded their ability to grip the road; this could reduce the operator’s ability to control the vehicle, potentially resulting in a loss of vehicle control, vehicle rollover, personal injury and death. If your AdvanceTrac威 with RSC威 system activates, SLOW DOWN.
201
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
WARNING: If a failure has been detected within the AdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ icon
will illuminate steadily. Verify that the AdvanceTrac威 with RSC威 system is not manually disabled (push the AdvanceTrac威 with RSC威 “Off “ button located on the center of the instrument panel). If the ⬙sliding car⬙ icon still illuminates steadily, have the system service by an authorized dealer immediately. Operating your vehicle with AdvanceTrac威 with RSC威 disabled could lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
The AdvanceTrac威 with RSC威 system provides the following stability enhancement features for certain driving situations: • Traction Control (TCS), which functions to help avoid drive-wheel • Electronic Stability Control (ESC), which functions to help avoid skids • Roll Stability Control™ (RSC威), which functions to help avoid a
spin and loss of traction.
or lateral slides
vehicle roll-over.
The AdvanceTrac威 with RSC威 system automatically enables each time the engine is started. All features of the AdvanceTrac威 with RSC威 system (TCS, ESC, and RSC威) are active and monitor the vehicle from start-up. However, the system will only intervene if the driving situation requires it. The AdvanceTrac威 with RSC威 system includes an AdvanceTrac威 with RSC威 ⬙Off⬙ button on the center of the instrument panel, and a “sliding car” icon instrument cluster. The “sliding car” in the instrument cluster icon will illuminate temporarily during start-up as part of a normal system self-check, or during driving if a driving situation causes the AdvanceTrac威 with RSC威 system to operate. If the “sliding car” icon AdvanceTrac威 with RSC威 system is not manually disabled by pressing the AdvanceTrac威 with RSC威 ⬙Off⬙ button located on the center stack of the instrument panel. If the “sliding car” icon illuminated, or if the message center (if equipped) displays SERVICE RSC NOW, have the system serviced by an authorized dealer immediately.
illuminates steadily, verify that the
remains steadily
in the
202
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
When AdvanceTrac威 with RSC威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off. When an event occurs that activates AdvanceTrac威 with RSC威 you may experience the following: • A slight deceleration of the vehicle • The “sliding car” • A vibration in the pedal when your foot is on the brake pedal • If the driving condition is severe and your foot is not on the brake, the brake pedal may move as the systems applies higher brake forces. You may also hear a whoosh of air from under the instrument panel during this severe condition.
indicator light will flash.
• The brake pedal may feel stiffer than usual. Traction Control (TCS) Traction Control is a driver aid feature that helps your vehicle maintain traction of the wheels, typically when driving on slippery and/or hilly road surfaces, by detecting and controlling wheel spin. Excessive wheel spin is controlled in two ways, which may work separately or in tandem: Engine Traction Control and Brake Traction Control. Engine Traction Control works to limit drive-wheel spin by momentarily reducing engine power. Brake Traction Control works to limit wheel spin by momentarily applying the brakes to the wheel that is slipping. Traction Control is most active at low speeds. During Traction Control events the “sliding car” icon instrument cluster will flash. If the Traction Control system is activated excessively in a short period of time, the braking portion of the system may become temporarily disabled to allow the brakes to cool down. In this situation, Traction Control will use only engine power reduction or transfer to help control the wheels from over-spinning. When the brakes have cooled down, the system will regain all features. Anti-lock braking, RSC威, and ESC are not affected by this condition and will continue to function during the cool-down period. The Engine Traction Control and Brake Traction Control system may be deactivated in certain situations. See the Switching Off AdvanceTrac威 with RSC威 section following.
in the
203
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
Electronic Stability Control (ESC) Electronic Stability Control (ESC) may enhance your vehicle’s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway. ESC operates by applying brakes to one or more of the wheels individually and, if necessary, reducing engine power if the system detects that the vehicle is about to skid or slide laterally. During Electronic Stability Control events the “sliding car” icon instrument cluster will flash. Certain adverse driving maneuvers may activate the Electronic Stability Control system, which include but are not limited to: • Taking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Driving over a patch of ice or other slippery surfaces • Changing lanes on a snow-rutted road • Entering a snow-free road from a snow-covered side street, or vice • Entering a paved road from a gravel road, or vice versa • Cornering while towing a heavily loaded trailer (refer to Trailer
in the
versa
towing in the Tires, Wheels and Loading chapter).
The Electronic Stability Control system may be deactivated in certain situations. See the Switching Off AdvanceTrac威 with RSC 威 section following. Roll Stability Control™ (RSC威) Roll Stability Control™ (RSC威) may help to maintain roll stability of the vehicle during adverse maneuvers. RSC威 operates by detecting the vehicle’s roll motion and the rate at which it changes and by applying the brakes to one or more wheels individually. During an event that activates the Roll Stability Control™ (RSC威) the “sliding car” icon Certain adverse driving maneuvers may activate the Roll Stability Control system, which include: • Emergency lane-change • Taking a turn too fast • Quick maneuvering to avoid an accident, pedestrian or obstacle The Roll Stability Control system may be deactivated in certain situations. See the Switching Off AdvanceTrac威 with RSC威 section following.
in the instrument cluster will flash.
204
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
Switching Off AdvanceTrac威 with RSC威 If the vehicle is stuck in snow, mud or sand, and seems to lose engine power, switching off certain features of the AdvanceTrac威 with RSC威 system may be beneficial because the wheels are allowed to spin. This will restore full engine power and will enhance momentum through the obstacle. To switch off the AdvanceTrac威 with RSC威 system partially, press the AdvanceTrac威 with RSC威 ⬙Off⬙ button below 20 mph (32 km/h). Full features of the AdvanceTrac威 with RSC威 system can be restored by pressing the AdvanceTrac威 with RSC威 ⬙Off⬙ button again or if the vehicle is above 20 mph (32 km/h) or by turning off and restarting the engine. If you switch off the AdvanceTrac威 with RSC威 system below 20 mph (32 km/h), the sliding car⬙ icon AdvanceTrac威 with RSC威 ⬙Off⬙ button again or if the vehicle is above 20 mph (32 km/h) will turn off the ⬙sliding car⬙ not allow partial AdvanceTrac威 with RSC威 system disabling above 20 mph (32 km/h). In R (Reverse), ABS and the Engine and Brake Traction Control features will continue to function; however, ESC and RSC威 are disabled.
will illuminate steadily. Pressing the
icon. The switch will
AdvanceTrac威 with RSC威 Features
Button functions
Default at start-up
“Sliding
car”
icon
Illuminated during bulb
check
RSC威
ESC
Traction Control
Enabled
Enabled
Enabled
Button pressed momentarily
Illuminated
solid
Enabled
Enabled
Disabled
below 20 mph
(32 km/h)
Button pressed again after deactivation or driving above 20 mph (32 km/h)
Not
illuminated
Enabled
Enabled
Enabled
205
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
stops) for more than a few seconds when the engine is running.
(If the fluid level is below the FULL COLD range on the dipstick).
STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it • Do not operate the vehicle with a low power steering pump fluid level • Some noise is normal during operation. If the noise is excessive, check for low power steering pump fluid level before seeking service by your authorized dealer. • Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by your authorized dealer. • Do not fill the power steering pump reservoir above the FULL COLD range on the dipstick, as this may result in leaks from the reservoir.
If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull.
TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle. The axle may exhibit a slight noise or vibration in tight turns with low vehicle speed. This is normal behavior and indicates the axle is working.
206
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
PREPARING TO DRIVE
WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.
WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher center of gravity than a passenger car.
WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed or abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Do not overload
your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle. Over-loading or loading the vehicle improperly can deteriorate handling capability and contribute to loss of vehicle control and vehicle rollover.
Vehicle stability and handling The risk of a rollover crash increases as the number of people and load in the vehicle increase. This increased risk occurs because the passenger weight and load raises the vehicle’s center of gravity and causes it to shift rearward. As a result, the van has less resistance to rollover and handles differently from other commonly driven passenger vehicles, making it more difficult to control in an emergency situation. Placing any load on the roof also raises the center of gravity and increases the potential for rollover. The van should be operated by an experienced driver. An organization that owns a 15–passenger van should select one or two experienced
207
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
drivers to drive the van on a regular basis. These drivers will gain valuable experience handling the van. This experience will help make each trip safer. The van should be operated at a safe speed which, in some conditions, may be less than the posted speed limit. Further, all occupants should be properly restrained. Most people killed in rollover crashes were unbelted. Occupants can dramatically reduce their risk of being killed or seriously injured in a rollover crash by simply using their seat belts. Organizations that own 15–passenger vans should have a written seat belt use policy. Drivers should be responsible for enforcing the policy. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control, not more. Additionally, smooth variations of the accelerator and/or brake pedal pressure should be utilized if changes in vehicle speed are called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surface to return the vehicle to a safe direction of travel.
• In the event of an emergency stop, avoid skidding the tires and do not
attempt any sharp steering wheel movements.
WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. • If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs.
208
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
AUTOMATIC TRANSMISSION OPERATION
Brake-shift interlock The vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) position with the ignition in the 4 (on) position and the brake pedal depressed, a malfunction may have occurred. It is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter. If the fuses and brakelamps are working properly, and the vehicle still will not shift out of (P) Park, see your authorized dealer for service. If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, and turn the ignition to the 4 (on) position. 2. Remove the lower trim panel under the steering column. Make sure not disturb the wires on the electrical connector. 3. Locate the BSI solenoid underneath the steering column. 4. With your hand, pull back on the solenoid, and at the same time, shift the transmission into N (Neutral).
5. Start the vehicle. See your authorized dealer for service immediately.
WARNING: Do not drive your vehicle until you verify that the brakelamps are working.
209
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the lock
position and remove the key whenever you leave your vehicle.
WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be
working properly. See your authorized dealer.
Understanding the gearshift positions of the 4–speed automatic transmission
This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected. The Adaptive Transmission Strategy allows the transmission to relearn these operating parameters. This learning process could take several transmission upshifts and downshifts; during this learning process, slightly firmer shifts may occur. After this learning process, normal shift feel and shift scheduling will resume. P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park)
210
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the
LOCK position and remove the key whenever you leave your vehicle.
R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position.
(Overdrive)
The normal driving position for the best fuel economy. Transmission operates in gears one through four.
Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever.
The O/D OFF lamp will illuminate in the instrument cluster.
O/D
ON/OFF
O/D OFF
Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to
other gears. Examples: heavy city traffic where continuous shifting in and out of overdrive occurs, hilly terrain, heavy loads, trailer towing and when engine braking is required. • To return to O/D (Overdrive), press the transmission control switch. • O/D (Overdrive) is automatically returned each time the key is turned
The O/D OFF lamp will not be illuminated.
off.
211
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to • Selecting 2 (Second) at higher speeds will cause the transmission to
(Overdrive), move the gearshift lever into the
(Overdrive) position.
downshift to second gear at the appropriate vehicle speed.
1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)
when vehicle reaches slower speeds.
Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. Understanding the shift positions of the 5–speed automatic transmission (if equipped - 5.4L and 6.8L gasoline engines only)
This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected. The Adaptive Transmission Strategy allows the transmission to relearn these operating parameters. This learning process could take several transmission upshifts and downshifts; during this learning process, slightly firmer shifts may occur. After this learning process, normal shift feel and shift scheduling will resume.
212
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park)
WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the
LOCK position and remove the key whenever you leave your vehicle.
R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with Tow/Haul OFF D (Overdrive) with Tow/Haul OFF is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through five. D (Overdrive) with Tow/Haul ON The Tow/Haul feature improves transmission operation when towing a trailer or a heavy load. All transmission gear ranges are available when using Tow/Haul.
213
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
To activate Tow/Haul, press the button on the end of the gearshift lever.
The TOW HAUL indicator light will illuminate in the instrument cluster.
Tow/Haul delays upshifts to reduce frequency of transmission shifting. Tow/Haul also provides engine braking in all forward gears when the transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the driver in controlling the vehicle when descending a grade. Depending on driving conditions and load conditions, the transmission may downshift, slow the vehicle and control the vehicle speed when descending a hill, without the accelerator pedal being pressed. The amount of downshift braking provided will vary based upon the amount the brake pedal is depressed. To deactivate the Tow/Haul feature and return to normal driving mode, press the button on the end of the gearshift lever. The TOW HAUL light will no longer be illuminated. When you shut-off and restart the engine, the transmission will automatically return to normal D (Overdrive) mode (Tow/Haul OFF).
WARNING: Do not use the Tow/Haul feature when driving in icy or slippery conditions as the increased engine braking can cause
the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control.
3 (Third) Transmission starts and operates in third gear only. Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever.
214
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving • The transmission will not downshift into 1 (First) at high speeds; it will downshift to a lower gear and then shift into 1 (First) when the vehicle reaches slower speeds.
Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. Understanding the shift positions of the 5–speed automatic transmission (if equipped - diesel engines only)
This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected. The Adaptive Transmission Strategy allows the transmission to relearn these operating parameters. This learning process could take several transmission upshifts and downshifts; during this learning process, slightly firmer shifts may occur. After this learning process, normal shift feel and shift scheduling will resume. P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park)
215
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the
LOCK position and remove the key whenever you leave your vehicle.
R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive D (Drive) with Overdrive is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through five. D (Drive) without Overdrive D (Drive) without Overdrive can be activated by pressing the transmission control switch (TCS) on the end of the gearshift lever. • This position allows for all forward gears except overdrive. • The O/D OFF lamp will illuminate
ON/OFF
O/D
in the instrument cluster. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to
O/D OFF
other gears. Examples: heavy city traffic where continuous shifting in and out of overdrive occurs, hilly terrain, heavy loads, trailer towing and when engine braking is required. • To return to O/D (Overdrive), press the transmission control switch. • O/D (Overdrive) is automatically returned each time the key is turned
The O/D OFF lamp will not be illuminated.
off.
3 (Third) Transmission starts and operates in third gear only.
216
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
Used for improved traction on slippery roads. Selecting 3 (Third) provides additional engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • The transmission will not downshift into 1 (First) at high speeds; it will downshift to a lower gear and then shift into 1 (First) when the vehicle reaches slower speeds.
Forced downshifts • Allowed in D (Drive) with Overdrive or D (Drive) without Overdrive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
• It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
• It often may be less risky to strike small objects, such as highway
reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or roll over. Remember, your safety and the safety of others should be your primary concern.
WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
217
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects.
WARNING: To help avoid personal injury, please read and understand the limitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at “parking speeds”. Inclement weather may also affect the function of the RSS; this may include reduced performance or a false activation.
WARNING: To help avoid personal injury, always use caution when in reverse and when using the RSS.
WARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
WARNING: Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps.
218
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the RSS detects a stationary or receding object further than 10 inches (25.0 cm) from the side of the vehicle, the tone will sound for only three seconds. Once the system detects an object approaching, the tone will sound again.
While receiving a warning, on some radios, the volume will be reduced to a predetermined level. After the warning goes away, the radio will return to the previous value. The RSS automatically turns on when the gear selector is placed in R (Reverse) and the ignition is on. A control in the message center allows the driver to disable the system only when the ignition is on and the gear selector is in R (Reverse). Refer to Message center in the Driver Controls chapter for more information. Keep the RSS sensors (located on the rear bumper/fascia) free from snow, ice and large accumulations of dirt (do not clean the sensors with sharp objects). If the sensors are covered, it will affect the accuracy of the RSS. If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.
219
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear-view camera system located on the back door provides a video image, which appears in the rear view mirror or navigation screen (if equipped), of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle.
To use the camera system, place the transmission in R (Reverse); an image will display on the left portion of the rear view mirror or on the navigation screen (if equipped). The area displayed on the screen may vary according to the vehicle orientation and/or road condition. • (1) Rear bumper • (2) Red zone • (3) Yellow zone • (4) Green zone • (5) Centerline of vehicle Always use caution while backing. Objects in the red zone are closest to your vehicle and objects in the green zone are further away. Objects are getting closer to your vehicle as they move from the green zone to the yellow or red zones. Use the side mirrors and rear view mirror to get better coverage on both sides and rear of the vehicle. When shifting out of R (Reverse) and into any other gear, the image will remain on for a few seconds before it shuts off to assist in parking or trailer hookup. If equipped with the Navigation system, after shifting out of R (Reverse) and into any gear other than P (Park), the image will remain until the vehicle speed reaches 5 mph (8 km/h), only if the rear camera delay feature is on, or until any navigation radio button is depressed.
220
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
Note: The default setting for the rear camera delay is off. Push the “Settings” button found on the navigation screen (if equipped) to set the rear camera delay feature to on or off. When towing, the camera system will only see what is being towed behind the vehicle; this might not provide adequate coverage as it usually provides in normal operation and some objects might not be seen. The camera lens for the camera system is located on the backdoor, above the license plate. Keep the lens clean so the video image remains clear and undistorted. Clean the lens with a soft, lint-free cloth and non-abrasive cleaner. Note: If the camera system image is not clear or seems distorted, it may be covered with water droplets, snow, mud or any other substance. If this occurs, clean the camera lens before using the camera system.
WARNING: The camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with
the rear view mirror and the side mirrors for maximum coverage.
WARNING: Objects that are close to either corner of the bumper or under the bumper, might not be seen on the screen
due to the limited coverage of the camera system.
WARNING: Backup as slow as possible since higher speeds might limit your reaction time to stop the vehicle.
WARNING: Do not use the camera system with the backdoor open.
If the back end of the vehicle is hit or damaged, then check with your authorized dealer to have your rear video system checked for proper coverage and operation. Night time and dark area use At night time or in dark areas, the camera system relies on the reverse lamp lighting to produce an image. Therefore it is necessary that both reverse lamps are operating in order to get a clear image in the dark. If either of the lamps are not operating, stop using the camera system, at least in the dark, until the lamp(s) are replaced and functioning.
221
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
the system inspected by your authorized dealer.
Servicing • If the image comes on while the vehicle is not in R (Reverse), have • If the image is not clear, then check if there is anything covering the lens such as dirt, mud, ice, snow, etc. If the image is still not clear after cleaning, have your system inspected by your authorized dealer.
VEHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off or PTO, is often added to the engine or transmission to operate utility equipment. Examples include a wheel-lift for tow trucks, cranes, tools for construction or tire service and pumping fluids. PTO applications draw auxiliary horsepower from the powertrain, often while the vehicle is stationary. In this condition, there is limited cooling air flow through the radiator and around the vehicle that normally occurs when a vehicle is moving. The aftermarket PTO system installer, having the most knowledge of the final application, is responsible for determining whether additional chassis heat protection or powertrain cooling is required, and alerting the user to the safe and proper operation. Your vehicle is qualified for use as a stationary power source, within limits detailed in the Ford Truck Body Builders Layout Book, found at www.fleet.ford.com/truckbbas, and through the Ford Truck Body Builders Advisory Service. Gas engine vehicles are qualified for up to 10 minutes of continuous operation as a stationary power source, due to the potential for the normal venting of fuel vapors. For stationary PTO operation of extended duration (beyond 10 minutes), diesel engine is recommended. Further consult your aftermarket PTO installer, since the duration of operation limit for the aftermarket PTO may be less than the vehicle is capable of.
222
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Driving
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the water, always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. Wet brakes do not stop the vehicle as quickly as dry brakes.
223
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
ROADSIDE ASSISTANCE
Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadside Assistance Card
included in your Owner Guide portfolio.
responsibility)
supplied with a tire inflation kit)
Roadside assistance will cover: • a flat tire change with a good spare (except vehicles that have been • battery jump start • lock-out assistance (key replacement cost is the customer’s • fuel delivery – Independent Service Contractors, if not prohibited by state, local or municipal law shall deliver up to 2.0 gallons (7.5L) of gasoline or 5 gallons (18.9L) of diesel fuel to a disabled vehicle. Fuel delivery service is limited to two no-charge occurrences within a 12-month period. • winch out – available within 100 feet (30.5 meters) of a paved or • towing – Ford/Mercury/Lincoln eligible vehicle towed to an authorized dealer within 35 miles (56.3 km) of the disablement location or to the nearest authorized dealer. If a member requests to be towed to an authorized dealer more than 35 miles (56.3 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 miles (56.3 km).
county maintained road, no recoveries.
Trailers shall be covered up to $200 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services.
224
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our website at www.ford.ca.
Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Owner Information Guide in the glove compartment. U.S. Ford, Mercury and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. Canadian customers who require roadside assistance, call 1-800-665-2006. Motorhome customers in the U.S and Canada should contact 1-800-444-3311. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles. To obtain reimbursement information, U.S. Ford, Mercury and Lincoln vehicle customers call 1-800-241-3673. Customers will be asked to submit their original receipts. Canadian customers who need to obtain reimbursement information, call 1-800-665-2006.
225
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery.
FUEL PUMP SHUT-OFF SWITCH (DIESEL-POWERED AND STRIPPED CHASSIS VEHICLES ONLY) This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. On diesel-powered vehicles, this switch is located in the front passenger’s footwell, by the kick panel.
226
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
On commercial stripped chassis vehicles, this switch is located on a bracket above the brake pedal. To reset the switch: 1. Turn the ignition off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition on. 5. Wait a few seconds and return the key to off. 6. Make another check for leaks.
Fuel pump shut-off (gas engines except stripped chassis) In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you may restart your vehicle by doing the following: 1. Turn the ignition switch to the off position. 2. Turn the ignition switch to the on position. In some instances the vehicle may not restart the first time you try to restart and may take one additional attempt.
WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision.
227
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color
15
COLOR
Mini fuses
Grey Violet Pink Tan
Brown
Red Blue Yellow Natural Green
— — — — —
Standard
fuses
Grey Violet Pink Tan
Brown
Red Blue Yellow Natural Green
— — — — —
Maxi fuses
— — — — — — —
Yellow
—
Green Orange
Red Blue Tan
Natural
Cartridge
maxi fuses
— — — — — — — Blue — Pink Green Red Yellow
—
Black
Fuse link cartridge
— — — — — — — Blue — Pink Green Red Yellow Brown Black
Fuse rating
2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A
Passenger compartment fuse panel The fuse panel is located to the left of the brake pedal and mounted onto the lower left cowl panel. Remove the fuse panel cover to access the fuses.
228
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
WARNING: Always disconnect the battery before servicing high current fuses.
If your vehicle is equipped with an auxiliary battery, disconnecting the primary under-hood battery DOES NOT remove power from all circuits. To remove a fuse use the fuse puller tool provided on the inside of the fuse panel cover.
The fuses are coded as follows.
Fuse/Relay Location
Fuse Amp
Rating
30A 15A 15A 30A 10A
Protected Circuits
Not used (spare) Not used (spare) Not used (spare) Not used (spare) SPDJB/Brake shift interlock
229
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Fuse/Relay Location
Fuse Amp
Rating
Protected Circuits
10
11
12
13
14
15
16
17
18
19
2021
22
23
24
25
26
27
28
29
30
31
32
33
3420A 10A 10A 15A 15A 10A 7.5A 5A 10A 10A 15A 20A 20A 25A 15A
15A 15A 15A 20A 10A 10A 20A 5A 5A 5A 10A 10A 10A 5A
Turn signal, Hazard, Stop lamps Left low beam Right low beam Courtesy lamps Switch illumination Not used (spare) Not used (spare) Mirrors Not used (spare) Not used (spare) Not used (spare) Door locks Not used (spare) Not used (spare) Diagnostic connector (except stripped chassis) Not used (spare) Park lamps, License plate lamps High beams Horn (except stripped chassis) Demand lighting Cluster (except stripped chassis) Ignition switch feed Audio mute (start) Cluster (except stripped chassis) Not used (spare) Not used (spare) Restraints module Trailer Brake Controller Not used (spare)
230
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Fuse/Relay Location
Fuse Amp
Rating
Protected Circuits
35
36
3738
39
40
4142
4344
45
46
4748
10A
5A 10A
20A 20A 20A 15A
10A 10A
10A
5A
7.5A
30A circuit
breaker Relay
Reverse park aid, Rear video camera, Cutaway run/start PATS RF module Climate control, Stripped chassis IP #1 run/start Not used (spare) Radio, Navigation Amplifier Radio, Switch illumination, Reverse camera mirror Upfitter switch Overhead console, Stripped chassis IP1
Auxiliary battery relay/Trailer tow battery charger relay Wipers, Stripped chassis Engine connector 3
PADI Windows accessory delayDelayed accessory
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
WARNING: Always disconnect the battery before servicing high current fuses.
WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
231
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
If your vehicle is equipped with an auxiliary battery, disconnecting the primary under-hood battery DOES NOT remove power from all circuits. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.
The high-current fuses are coded as follows.
Fuse/Relay Location
Fuse Amp
Rating
Protected Circuits
10
11
12HC Micro Relay Powertrain Control Module (PCM) HC Micro Relay Starter solenoid HC Micro Relay Wiper HC Micro Relay Trailer tow battery charge HC Micro Relay Fuel pump HC Micro Relay Trailer tow park lamp HC Micro Relay Upfitter #4
HC Micro Relay Upfitter #3
HC Micro Relay Modified vehicle and strippedHC ISO
—
40A**
chassis run/start IDM relay (Diesel engine only) Not used Modified vehicle and stripped chassis run/start
232
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Fuse Amp
Protected Circuits
Rating 30A** 40A** 40A**
50A** 50A**
30A**
30A** 30A** 50A**
—
G8VA relay G8VA relay
Starter solenoid relay Run start relay Modified vehicle and stripped chassis battery Auxiliary A/C blower Auxiliary battery feed, Trailer tow battery charge, trailer tow park feed Electric trailer brake, Trailer brake controller Upfitter #1
Upfitter #2
IDM relay (diesel engine only) Not used A/C clutch Horn relay (Stripped chassis)— —
20A* 10A* 10A* 10A*
HC Micro relay Run/start Not used Not used Back up lamp A/C clutch BOO switch Cluster battery (stripped chassis only), IDM coil (diesel engine only) Blower motor ABS pump Stripped chassis horn PCM relay Ignition switch (Stripped chassis only) Trailer tow stop/LH turn signal
50A** 40A** 20A** 40A** 20A**
G8VA relay
Fuse/Relay Location
13
14
1516
1718
19
20
21
22
23
24
25
26
27
28
29
30
3132
33
34
35
3637
233
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Fuse/Relay Location
38
39
40
41
4243
44
45
4647
48
49
50
51
5253
5455
56
57
58
59
6061
62
63
64Fuse Amp
Rating
G8VA relay G8VA relay ISO relay
10A* 15A*
20A* 10A* 15A* 10A*
40A** 20A** 30A**
—
20A** 10A*
10A* 10A*
10A* 20A* 20A* 15A*
— —
—
Protected Circuits
Trailer tow stop/RH turn signal Back up lamp Blower motor Charging (diesel engine only) Diagnostic connector (stripped chassis) Fuel pump Upfitter #3
Upfitter #4
PCM keep alive power, Canister vent, PCM relay coil ABS coil Trailer tow stop lamp/turn signal Wiper motor Not used Cutaway Stripped chassis and modified vehicle run/start relay coil ABS run/start feed Fuel pump relay coil (gas engine only) ECM (diesel engine only) DFCM (diesel engine only) Trailer tow park lamp Trailer tow backup lamp Not used One Touch Integrated Start (OTIS) (diode) Auxiliary battery (diode)HC Micro relay Upfitter #2
30A**
—
Trailer tow battery charge Not used
234
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Fuse Amp
Protected Circuits
Rating 20A** 20A** 20A** 50A**
—
30A**
—
20A**
—
30A** 20A* 20A* 10A* 15A*
10A* 10A*
15A*
— — —
Power point 2 (glove box) Power point 3 (left-hand B-pillar) Power point 1 (instrument panel) Modified vehicle Not used Stripped chassis Not used Cigar lighter Not used Power seat VPWR 1, PCM power VPWR 2, PCM mil VPWR 3, PCM non mil VPWR 4 (gas engine only), Ignition coil (diesel engine only), Fuel pump relay coil VPWR 5, Transmission Cluster run/start (stripped chassis only) IDM logic (diesel engine only) Not used Fuel pump (diode) Not used
HC Micro relay Upfitter #1
Fuse/Relay Location
65
66
67
68
69
70
71
72
73
74
75
76
77
7879
8081
82
83
84
85* Mini fuses ** A1S fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle.
235
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensors, refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the TPMS sensor for damage.
WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System and should not be used.
WARNING: Refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter for important
information. If the tire pressure monitor sensor becomes damaged, it will no longer function.
Dissimilar spare tire/wheel information
WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.
If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the • Tow a trailer 236
Safety Compliance Label
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
tire
Roadside Emergencies • Use snow chains on the end of the vehicle with the dissimilar spare • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare
tire/wheel
The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack
237
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.
Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113 km/h). It is intended for temporary use only. This means if you need to use it, you should replace it as soon as possible.
Stopping and securing your vehicle 1. Park on a level surface. 2. Activate the warning flashers. 3. Place the gearshift in P (Park). 4. Apply the parking brake and turn the engine off.
Spare tire information The spare tire for your vehicle is stowed under the rear of your vehicle (except cutaway and stripped chassis models). To remove the spare tire: 1. Open the rear doors and remove the thumb screw and anti-theft bracket. If finger pressure will not remove the thumb screw, use the lug wrench to loosen the screw. 2. Remove the access plug under the left door.
238
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
3. Remove the jack handle from the right side compartment and insert the tip of the jack handle through the access hole and into the tube. 4. Turn the jack handle counterclockwise until the cable is slack and the tire can be slid from under the vehicle. 5. Remove the retainer from the spare tire. To stow the cable retainer with the spare removed, turn the jack handle clockwise until all slack is removed.
Tire change procedure
WARNING: To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in
both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
WARNING: If the vehicle slips off the jack, you or someone else could be seriously injured.
WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to
avoid the danger of being hit when operating the jack or changing the wheel.
1. Block the wheel that is diagonally opposite the tire you are changing. On E-450 vehicles, the parking brake is on the transmission. Therefore, the vehicle will not be prevented from moving when a rear wheel is lifted, even if the parking brake is applied. Be sure to block both directions of the wheel that is diagonally opposite to the wheel that is being lifted. 2. Remove the spare tire and jack from the storage location.
239
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies • the jack is located in the rear
right-hand side of the cargo area.
3. Remove any wheel trim. Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off. 4. Loosen the wheel nut by pulling up on the handle of the lug nut wrench about one-half turn (counterclockwise). Do not remove the wheel lug nuts until you raise the tire off the ground.
WARNING: When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or
slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or R (Reverse) (manual transmission). To help prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and the diagonally opposite wheel is blocked.
Replacing the tire 1. Assemble the jack handle sections together and lock into the jack. Use the jack handle to slide the jack under the vehicle.
240
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not
start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
2. Position the jack to raise the front or rear wheel. • Never use the front or rear
differential as a jacking point.
Rear axle jacking points - All models except E-350 Dual Rear Wheel (DRW) and E-450:
Rear axle jacking points - E-350
Dual Rear Wheel (DRW) and E-450:2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
241
Roadside Emergencies
Front axle jacking points: Place the jack under the pin on the front surface of the front axle. Do not place the jack under or on the steering linkage. • Raise the jack until the wheel is completely off the ground. (Turn jack handle clockwise if your vehicle is equipped with a screw-type jack or pump the jack if equipped with a hydraulic jack.)
• Remove the lug nuts with the lug • Replace the flat tire with the
nut wrench.
spare tire.
If your vehicle has single rear wheels, thread the lug nuts on the studs with the beveled face toward the wheel. If your vehicle has dual rear wheels, thread the two element swiveling lug nuts on the studs with the flange facing toward the wheel. 3. Use the lug nut wrench to screw the lug nut snugly against the wheel. 4. Lower the vehicle by turning the jack handle counterclockwise.
242
2009 Econoline (eco) Owners Guide, 2nd Printing USA (fus)
Roadside Emergencies
5. Remove the jack and fully tighten the lug nuts in the following pattern (Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification):
WARNING: Never use wheels or lug nuts different
than the original equipment as this could damage the wheel or mounting system. This damage could allow the wheels to come off while the vehicle is being driven.
6. Install any wheel covers, ornaments or hub caps. Make sure they are snapped in place. 7. Stow the jack, handle and lug wrench. 8. Unblock the wheels. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the direction specified on the Tire Changing Instructions located with the jack hardware. 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center. Pull on the cable to align the components at the end of the cable. 3. Turn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when
