2008 Ford Crown Victoria Owners Manual

traction. Using ABS • In an emergency or when maximum efficiency from the four-wheel

ABS is required, apply continuous force on the brake. The four wheel ABS will be activated immediately, thus allowing you to retain steering control of your vehicle and, providing there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop.

181

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving • The anti-lock system does not reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop.

• We recommend that you familiarize yourself with this braking

technique. However, avoid taking any unnecessary risks.

ABS

ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately.) Parking brake with auto-release (if equipped) Apply the parking brake whenever the vehicle is parked. To set the parking brake: 1. Move the gearshift to P (Park). 2. Push pedal downward.

BRAKE

HOOD

The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released.

BRAKE

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the OFF/LOCK position

and remove the key whenever you leave your vehicle.

182

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected. Your vehicle may be equipped with an automatic parking brake release. To release the parking brake: 1. Start the vehicle. 2. Press the brake pedal. 3. Move the gearshift from the P (Park) position to one of the forward gears (the parking brake will not release automatically when you shift into reverse). The brake pedal must remain pressed while the gearshift is moved. If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the lever to manually release the parking brake.

TRACTION CONTROL™ (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control™ system. This system helps you maintain the stability and steerability of your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates by detecting and controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS). Wheel-speed sensors allow excess rear wheel spin to be detected by the Traction Control™ portion of the ABS computer. Any excessive wheel spin is controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a second and adjustments are made accordingly.

183

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal

injury or property damage. The occurrence of an Traction Control™ event is an indication that at least some of the tires have exceeded their ability to grip the road; this may lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. If you experience a severe road event, SLOW DOWN.

The Traction Control™ system will allow your vehicle to make better use of available traction on slippery surfaces while you are trying to accelerate or while your foot is on the accelerator pedal. The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads. During Traction Control™ operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior. If you should become stuck in snow or ice or on a very slippery road surface, try switching the Traction Control™ system off. This may allow excess wheel spin to “dig” the vehicle out and enable a successful “rocking” maneuver. The traction control indicator flashes during a Traction Control™ system event. If the traction control indicator comes on and stays lit, either: • the Traction Control™ system • the customer has disabled the system using the traction control switch

requires service by an authorized dealer, or

located on the left side of the instrument panel.

The Traction Control™ system will be on every time you turn the ignition key from OFF to ON until you deactivate the system using the traction control switch on the instrument panel left of the steering column.

184

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

STEERING

Ford Motor Company recommends that an authorized dealer inspect all steering column assemblies in use in vehicles involved

in a collision. Failure to inspect and if necessary replace the steering column assembly could result in severe injury or death in the event of a collision.

Do not attempt to service, repair, or modify the steering column, its adaptive module, or its fuses. See your authorized dealer.

(below the MIN mark on the reservoir).

To help prevent damage to the power steering system, never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. It is also important to maintain a proper power steering fluid level in the power steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level • Some noise is normal during operation. If the noise is excessive, check for low power steering pump fluid level before seeking service by your authorized dealer. • Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by your authorized dealer. • Do not fill the power steering pump reservoir above the MAX mark on

the reservoir, as this may result in leaks from the reservoir.

If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased.

185

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your authorized dealer.

AIR SUSPENSION SYSTEM (IF EQUIPPED) The air suspension system is designed to improve ride, handling and general vehicle performance during: • Certain road conditions • Steering maneuvers • Braking • Accelerations This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate.

AIR SUSPENSION SWITCH

On vehicles equipped with Air Suspension, turn OFF

the Air Suspension switch prior to jacking, hoisting or towing your vehicle.

Normal vehicle operation does not require any action by the driver.

OFF

INTERRUPTEUR DE LA SUSPENSION PNEUMATIQUE WARNING To prevent sudden vehicle movement, turn off air suspen- sion switch prior to jacking, hoisting or towing vehicle. AVERTISSEMENT Pour prévenir tout mouvement soudain du véhi- cule, placer à l'arrêt l'interrupteur de la suspension pneumatique avant de lever le véhicule (cric ou pont élévateur) ou de le remorquer.

OFF-ARRET

TRACTION-LOK™ AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok™ axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a Traction-Lok™ rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver.

186

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

AUTOMATIC TRANSMISSION OPERATION

Brake-shift interlock – column-shift transmission This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter. If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to 2 (ACC). 2. Locate the access plug on the underside of the steering column cover.

3. Remove the access plug using a flat head screwdriver. Insert the screwdriver into the access hole nearest the steering wheel. Then push and hold the override button using a flat head screwdriver. Apply the brake pedal and shift the transmission into N (Neutral) while continuing to depress the override button. 4. Reinstall the access plug cover, start the vehicle and release the parking brake.

Do not drive your vehicle until you verify that the brakelamps are working.

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the OFF/LOCK position

and remove the key whenever you leave your vehicle.

187

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.

See your authorized dealer.

Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless the brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral).

When the key is in the ignition and in the ACC position, the automatic transmission shift lever can be moved from the P

(Park) position without the brake pedal depressed. To avoid unwanted vehicle movement, always set the parking brake.

3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter.

Do not drive your vehicle until you verify that the brakelamps are working.

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and

remove the key whenever you leave your vehicle.

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.

See your authorized dealer.

188

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Understanding the gearshift positions of the 4–speed automatic transmission

Driving

P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park)

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and

remove the key whenever you leave your vehicle.

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position.

(Overdrive)

The normal driving position for the best fuel economy. Transmission operates in gears one through four.

189

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving

If your vehicle is equipped with a column-shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift lever. If your vehicle is equipped with a floor-shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift handle.

O/D OFF

The transmission control indicator light (TCIL) will illuminate on the instrument cluster.

O/D OFF

Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears. Examples: city traffic, hilly terrain, heavy loads, trailer towing and when engine braking is required. • To return to O/D (overdrive mode), press the transmission control • O/D (Overdrive) is automatically returned each time the key is turned

switch. The O/D OFF lamp will not be illuminated.

off.

2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to

(Overdrive), move the gearshift lever into the

(Overdrive) position.

190

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Driving • Selecting 2 (Second) at higher speeds will cause the transmission to

downshift to second gear at the appropriate vehicle speed.

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)

when vehicle reaches slower speeds.

Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat.

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).

When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the water, always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. Wet brakes do not stop the vehicle as quickly as dry brakes.

191

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

ROADSIDE ASSISTANCE

Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadside Assistance Card

included in your Owner Guide portfolio.

supplied with a tire inflation kit)

Roadside assistance will cover: • a flat tire change with a good spare (except vehicles that have been • battery jump start • lock-out assistance (key replacement cost is the customer’s responsibility) • fuel delivery – Independent Service Contractors, if not prohibited by state, local or municipal law shall deliver up to 2.0 gallons (7.5L) of gasoline or 5 gallons (18.9L) of diesel fuel to a disabled vehicle. Fuel delivery service is limited to two no-charge occurrences within a 12-month period. • winch out – available within 100 feet (30.5 meters) of a paved or • towing – Ford/Mercury/Lincoln eligible vehicle towed to an authorized dealer within 35 miles (56.3 km) of the disablement location or to the nearest authorized dealer. If a member requests to be towed to an authorized dealer more than 35 miles (56.3 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 miles (56.3 km).

county maintained road, no recoveries.

Trailers shall be covered up to $200 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services. Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits

192

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Customer Information Guide in the glove compartment. U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount and for towing to the nearest dealership within 35 miles. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Customers will be asked to submit their original receipts. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.

Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your authorized dealer or by calling 1–800–FORD–CLUB. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our website at www.ford.ca.

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off.

193

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies • The hazard lights control is

located on top of the steering column.

• Depress hazard lights control to

activate all hazard flashers simultaneously.

• Depress control again to turn the

flashers off.

FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located on the left side of the trunk behind the left rear tail light and the trunk liner.

Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks.

194

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system.

FUSES AND RELAYS

Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color

15

COLOR

Mini fuses

Grey Violet Pink Tan

Brown

Red Blue Yellow Natural Green

—

Standard

fuses

Grey Violet Pink Tan

Brown

Red Blue Yellow Natural Green

—

Maxi fuses

— — — — — — —

Yellow

—

Green Orange

Fuse rating

2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A

Cartridge

maxi fuses

— — — — — — — Blue — Pink Green

Fuse link cartridge

— — — — — — — Blue — Pink Green

195

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

COLOR

Fuse rating

Mini fuses

Standard

fuses

50A 60A 70A 80A

— — — —

— — — —

Maxi fuses

Red Blue Tan

Natural

Cartridge

maxi fuses Red Yellow

—

Black

Fuse link cartridge

Red Yellow Brown Black

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.

27

18

25

16

26

17

23

14

24

15

21

12

22

13

19

10

20

11

Relay

33

31

29

32

30

28

196

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Passenger Compartment Fuse

Panel Description

Ignition (START) - Starter relay coil, DTRS Power mirrors, Door lock switches, Mirror switch, Keypad switch, Decklid switch, DDM, Cluster Ignition (START) - Audio mute, Police PDB (Police vehicles only) LCM (switch illumination), Autolamp sensor Ignition (ON/ACC) - LCM LCM Ignition (ON/ACC) - Wiper module Electronic Automatic Temperature Control (EATC) module (vehicles equipped with EATC only) Ignition (ON/ACC) - Door lock switch illumination, Heated seat switch illumination, Moon roof, Overhead console, Radio, Antenna, Electrochromatic mirror, Window relay coil (non-Police vehicles only), Window and decklid relay coil and Police ON/ACC relay coil (Police vehicles only) Hazards (non-Police vehicles only) Hazards (Police vehicles only) Ignition (ON) - Turn signals Audio

197

The fuses are coded as follows.

Fuse/Relay Location

Fuse Amp

Rating

10

11
12

10A

7.5A

5A

10A

7.5A 7.5A 10A

10A

7.5A

15A

20A 15A 15A

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Fuse/Relay Location

13

14
15

16
17

18

19
20

21
22

23

Fuse Amp

Rating

10A

15A 10A

20A 10A

15A

10A 10A

10A 10A

15A

Passenger Compartment Fuse

Panel Description

Ignition (ON) - Anti-lock Brake System (ABS) module, Rear Air Suspension Module (RASM), Variable Assist Power Steering (VAPS), Cluster Taxi, Adjustable pedals Ignition (ON) - EATC module, A/C mode switch (vehicles equipped with manual A/C only), A/C blower relay coil Cigar lighter, OBD II Ignition (ON) - A/C mode switch (vehicles equipped with manual A/C), Blend door, Heated seat modules, BTSI (Floor-shift transmission) Lighting control module (interior lighting) LCM (Left-hand low beam) Ignition (ON/START) - Back-up lamps LCM (Right-hand low beam) Ignition (ON/START) - Restraint Control Module (RCM), Occupant Classification Sensor (OCS), Passenger Airbag Deactivation Indicator (PADI) Multi-function switch (Flash-to-pass), LCM (High beams)

198

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Fuse/Relay Location

24

25
26

27
28
29
30

31
32
33

Fuse Amp

Rating

10A

15A 10A

— 7.5A 2A 2A

5A 2A 10A

Roadside Emergencies

Passenger Compartment Fuse

Panel Description

Ignition (ON/START) - Passive Anti-Theft System (PATS) module, Powertrain Control Module (PCM) relay coil, Fuel relay coil, Ignition coil relay coil LCM (Park lamps, license lamps) Ignition (ON/START) - Cluster, LCM, Overdrive cancel switch Not used Brake signal, LCM (BTSI), ABS Hazard in (Police vehicles only) Battery saver (Police vehicles only) Key in (LCM) Hazard out (Police vehicles only) Ignition (ON/START), Fire suppression module (if equipped) (Police vehicles only)

Relay 1

Full ISO relay Window relay, Decklid (Police

vehicles only)

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.

Always disconnect the battery before servicing high current fuses.

To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or

refilling fluid reservoirs.

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.

199

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

The high-current fuses are coded as follows.

Fuse/Relay Location

10
11

Fuse Amp

Rating 30A* 20A*

10A*

20A* 10A*

15A* 30A* 20A* 15A* 20A* 15A*

Power Distribution Box Description Ignition switch Moon roof, Spot lights (Police vehicles only) Powertrain Control Module (PCM) keep alive power, Canister vent Fuel relay feed Rear Air Suspension Module (RASM), VAPS module Alternator regulator PCM relay feed Driver’s Door Module (DDM) Ignition coil relay feed Horn relay feed A/C clutch relay feed

200

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Fuse/Relay Location

12

13
14
15

16

17
18
19
20
21
22

23

24

101
102
103

104

105
106

107

Fuse Amp

Rating 20A* 25A* 20A* 20A* 15A*

20A*

10A* 10A* 15A* 15A* 15A* 20A*

20A*

10A*

40A** 50A** 50A**

50A**

30A** 40A**

40A**

Roadside Emergencies

Power Distribution Box Description Audio (Subwoofer) Tray lamps (Police vehicles only) Instrument panel power point Stop lamp switch Police accessory battery feed 1
(Police vehicles only) Heated seats, Police accessory battery feed 2 (Police vehicles only) Commercial R/A Commercial R/A Injectors PCM Powertrain loads and sensors Police PDB outputs (Police vehicles only) Police PDB outputs (Police vehicles only) Heated mirrors, Rear defrost indicator Blower relay feed Cooling fan Instrument panel (I/P) fuse box feed #1, I/P fuses 10, 12, 14, 16
and 18
Instrument panel (I/P) fuse box feed #2, I/P fuses 2, 4, 6, 8, 19, 21, 23 and 25
Starter relay feed Anti-lock Brake System (ABS) module (Pump) Rear defroster relay feed

201

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Fuse/Relay Location

108

109
110
111

112

113

114

115

116

117

118

201
202
203
204
205
206
207

Fuse Amp

Rating 20A**

20A** 30A** 50A**

30A**

40A**

50A**

50A**

50A**

50A**

50A**

50A**

1⁄2 ISO relay

—

1⁄2 ISO relay 1⁄2 ISO relay

—

1⁄2 ISO relay

—

Power Distribution Box Description Police accessory battery feed 3
(Police vehicles only) ABS module (Valves) Wiper module Police PDB or Police accessory battery feed (Police vehicles only) Air suspension compressor (non-Police vehicles only) Police PDB relay feed (Police vehicles only) Police light bar or Police right-hand kick panel accessory battery feed (Police vehicles only) Police PDB or Police accessory battery feed (Police vehicles only) Rear power point or Police right-hand kick panel accessory battery feed (Police vehicles only) Police accessory battery feed (Police vehicles only) Police PDB or Police accessory battery feed (Police vehicles only) Rear power point or Police right-hand kick panel accessory battery feed (Police vehicles only) A/C clutch Not used Ignition coil PCM Not used Fuel Not used

202

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Fuse/Relay Location

208
209
301
302

303
304
501
502
503
601

602

Roadside Emergencies

Fuse Amp

Rating

—

Power Distribution Box Description Not used Horn Starter

1⁄2 ISO relay Full ISO relay Full ISO relay Air compressor (non-Police

Full ISO relay Full ISO relay

Diode Diode

—

20A Circuit

breaker

20A Circuit

breaker

vehicles only) RUN/ACC relay (Police vehicles only) Blower Rear defrost relay A/C clutch PCM Not used Power seats, Lumbar, Decklid (Police vehicles only) RUN/ACC relay (windows) (non-Police vehicles only) RUN/ACC relay feed (windows and decklid) (Police vehicles only)

* Mini fuse ** Cartridge fuse Relays Relays are located in the power distribution box and should be replaced by an authorized dealer. CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that is different in one or more of the following: type, brand, size, speed rating and tread design. If this is the case, this dissimilar spare tire is still rated for your vehicle loads (GAWR and GVWR). This temporary spare tire is not equipped with a Tire Pressure Monitor System (TPMS) sensor.

203

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use. To restore the full functionality of the TPMS system, all road wheels equipped with the tire pressure monitoring sensors must be mounted on the vehicle. Have a flat tire serviced by an authorized dealer in order to prevent damage to the TPMS sensor, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels, and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the TPMS sensor for damage.

The use of tire sealants may damage your Tire Pressure Monitoring System and should not be used.

Refer to Tire Pressure Monitoring System (TPMS) in the Tire, Wheels and Loading chapter for important information. If the

tire pressure monitor sensor becomes damaged, it will no longer function.

Dissimilar spare tire/wheel information

Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY”

204

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

tire

Safety Compliance Label

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessary, do not operate above speeds of 10 mph (16
km/h) or for distances above 50 miles (80 km). 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare

tire/wheel

The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs

205

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.

Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113
km/h). It is intended for temporary use only. This means if you need to use it, you should replace it as soon as possible. Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) and turn engine off.

HOOD

206

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Removing the spare tire and jack 1. Remove the spare tire and the jack. The jack could be located: • A — behind the mini spare tire or • B — behind the full size spare

tire

On vehicles equipped with Air Suspension, turn OFF

the Air Suspension switch prior to jacking, hoisting or towing your vehicle.

Refer to Air suspension system in the Driving chapter of the Owner’s Guide for more information. 2. Remove the lug wrench from the jack. Rotate the lug wrench socket out from the handle.

Roadside Emergencies

OFF

Tire change procedure

When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the

jack, even if the vehicle is in P (Park).

207

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions)

the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.

If the vehicle slips off the jack, you or someone else could be seriously injured.

Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the

danger of being hit when operating the jack or changing the wheel.

1. Block the diagonally opposite wheel.

2. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel. 3. If equipped with a full wheelcover, remove the wheelcover center ornament then loosen the five black plastic nuts which retain the wheelcover using the lug wrench. 4. Loosen each wheel metal lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.

Before placing the jack under the vehicle, NOTE the jack location

markings:

208

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

JACK LOCATION The jack location markings can be found on the lower outer edge of the body. • Locate the jack locator mark (B) on the body (C) near the tire you are changing, then place the jack (D) under the frame (A) of the vehicle aligning it with the mark (B). • Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground.

To lessen risk of personal injury, do not put any part

of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is ONLY meant for changing the tire.

• Never use the rear differential

as a jacking point.

5. Remove the metal lug nuts with the lug wrench. 6. Replace the flat tire/wheel assembly with the spare tire/wheel assembly, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 7. Lower the vehicle by turning the jack handle counterclockwise.

209

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

8. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 9. For full size spare aluminum wheel, firmly install the center ornament. If equipped with a full size spare tire/wheel assembly and lug nut retained full wheelcover, install the wheelcover by tightening the five black plastic nuts in the order shown on the wheelcover using the lug wrench with about 80 lb. in. (9 N•m) torque. Then firmly install the wheelcover center ornament. 10. Put flat tire, jack and lug wrench away. 11. Turn on the air suspension switch (if equipped).

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).

Bolt size

Wheel lug nut torque*

1⁄2 x 20
* Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.

lb.ft. 100

N•m 135

When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel

or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control.

210

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger. DO NOT apply grease to lugnut/stud holes or wheel-to-brake surfaces.

JUMP STARTING

The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or

vehicle damage.

Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.

Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage.

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.

211

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off.

Connecting the jumper cables

+–

+–

1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.

+–

+–

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.

212

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

+–

+–

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.

+–

+–

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.

Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an

explosion of the gases that surround the battery.

5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.

213

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.

Removing the jumper cables

+–

+–

Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.

+–

+–

2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.

214

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

+–

+–

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.

+–

+–

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.

215

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Roadside Emergencies

WRECKER TOWING

If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Before your vehicle can be towed, the air suspension control in the luggage compartment must be turned to the OFF position (if equipped). If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.

216

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

GETTING THE SERVICES YOU NEED

At home You must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford. If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. 2. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. 3. If you require assistance or clarification on Ford Motor Company policies or procedures, please contact the Ford Customer Relationship Center at 1-800-392-3673 (FORD).

Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you. In the United States: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) www.customersaskford.com

217

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you. In the United States: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
1-800-521-4140
(TDD for the hearing impaired: 1-800-232-5952) www.customersaskford.com In Canada: Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-387-9333
www.lincolncanada.com In order to help you service your Lincoln vehicle, please have the following information available when contacting the Lincoln Centre: • Your telephone number (home and business) • The name of the authorized dealer and the city where the authorized • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) Additional Assistance If you still have a complaint involving a warranty dispute, you may wish to contact the Better Business Bureau (BBB) AUTO LINE program (U.S. only).

dealer is located

218

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.

IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126

219

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. Initially, the BBB will try to resolve your question or concern through mediation. Mediation is a process through which a representative of the BBB will contact the parties and explore options for settlement of your claim. If mediation is not successful, customers with eligible claims may participate in the BBB AUTO LINE arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. You are not bound by the decision but may choose to accept it. If you choose to accept the BBB AUTO LINE decision then Ford must abide by the accepted decision as well. If the arbitrator has decided in your favor and you accept the decision, the BBB AUTO LINE program will contact you to ensure that Ford has complied with the decision in a timely manner. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. To initiate a claim with the BBB AUTO LINE, you will be asked for your name and address, general information about your new vehicle, information about your warranty concerns and any steps you have already taken to try to resolve them. You will then be mailed a Customer Claim Form that you will need to complete, provide proof of vehicle ownership, sign and return the Customer Claim Form to the BBB. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1–800–955–5100, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800
Arlington, Virginia 22203–1833
Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.

220

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.

FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. It provides the following: • Benefits during the warranty period depending on the plan you

purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).

• Protection against covered repair costs after your Bumper-to-Bumper

Warranty expires.

You may purchase Ford ESP from any participating authorized dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 4,600 participating authorized dealers.

221

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, write or call: FORD MOTOR COMPANY FORD EXPORT OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
If you are in another foreign country, contact the nearest authorized dealer. If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations. Customers in the U.S. should call 1–800–392–3673.

222

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207
Or call: For a free publication catalog, order toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.)

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer or by writing to: Ford Motor Company of Canada, Limited Service Publications CHQ202
The Canadian Road P.O. Box 2000
Oakville, ON, Canada L6J 5E4

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company.

223

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Customer Assistance

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: Administrator NHTSA 400 Seventh Street, SW Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from http://www.safercar.gov.

REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada, using their toll-free number: 1–800–333–0510.

224

2008 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)

Cleaning

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing

strong, direct sunlight.

or laundry liquid. These products can discolor and spot painted surfaces.

• Never wash a vehicle that is “hot to the touch” or during exposure to • Always use a clean sponge or car wash mitt with plenty of water for • Dry the vehicle with a chamois or soft terry cloth towel in order to • It is especially important to wash the vehicle regularly during the

eliminate water spotting.

best results.

winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppings

and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Bug and Tar Remover, ZC-42, which is available from your authorized dealer.

• Remove any exterior accessories, such as antennas, before entering a • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.

car wash.

Exterior chrome • Wash the vehicle first, using cool or lukewarm water and a neutral pH • Use Custom Bright Metal Cleaner (ZC-15), available from your

shampoo, such as Motorcraft Detail Wash (ZC-3-A).

authorized dealer. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.