Download PDF Manual

off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.


Warning returns after the ignition key is turned from OFF to ON.


Never remove the coolant reservoir cap while the engine is running or hot.


CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and Specifications chapter. CHECK AIR SUSPENSION. Displayed when the air suspension system is not operating properly. If this message is displayed while driving, pull off the road as soon as safely possible. For more information, refer to Air suspension in the Driving chapter.


79


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


LOW FUEL. Displayed as an early reminder of a low fuel condition. Warning message can be reset by pressing the RESET button, but will return after 10 minutes. If any other button is pressed besides RESET, the message ’’PRESS RESET TO CLEAR’’ will appear in the Message Center. Once this message disappears (after approximately 2 seconds), press RESET to clear the warning. TRUNK AJAR. Displayed when the trunk is not completely closed. OVERDRIVE ON/OFF. Displayed when the overdrive is enabled or disabled. CHECK COMPASS MODULE. Displayed when the compass is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW WASHER FLUID. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. CHANGE ENGINE OIL. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press and hold the RESET control for 2 seconds and release. Oil life is set to 100% and “OIL LIFE XXX% HOLD RESET IF NEW OIL” is displayed.


80


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Driver Controls


2. Press and hold the RESET control for 3 seconds and release. Oil life is set to 100% and “OIL LIFE START VALUE SET TO XXX%” is displayed.


POSITIVE RETENTION FLOOR MAT


Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the


brake pedals.


Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.


INTERIOR TRUNK CONTROL The remote trunk release control is located on the driver’s door trim panel and can be operated at any time. You can render the switch inoperable by locking the button with your master key.


If equipped with a perimeter alarm system, the remote trunk release control and power door locks will be disabled when the vehicle perimeter alarm system is armed. This control will not work until the vehicle perimeter alarm system is disarmed. Refer to Perimeter Alarm System in the Locks and Security chapter.


81


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


ignition and remote trunk release.


KEYS The vehicle is equipped with a master (black) key and valet (gray) key lock system (if equipped with valet feature). • The master key will access the vehicle’s doors, trunk, glove box, • The valet key (if equipped) will access doors and ignition only. Before using the valet key with an attendant, lock the interior trunk control to disable the interior trunk control located on the drivers door, then lock the glove compartment with your master key. Do not hand over the remote entry transmitter or the master key to the valet attendant. For more information, refer to Interior trunk control in the Driver Controls chapter.


POWER DOOR LOCKS


Power door trim switch inhibit This feature disables the power door locks and trunk interior release switches if all doors are closed and the perimeter alarm becomes armed. Once the power door trim switches are disabled, they can only become active when perimeter alarm is disarmed. Press control to unlock all vehicle doors.


Press control to lock all vehicle doors.


Smart locks (if equipped) With the key in any ignition position, and either the driver’s or passenger’s door open, the doors cannot be locked using the power door lock switches.


82


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


The vehicle may still be locked with the key in the ignition, and performing one of the following actions: • Pressing the manual lock button on the door. • Operating the remote entry transmitter (if equipped). • Operating the keyless entry keypad (if equipped). • Operating the driver’s door with a key. Autolock (if equipped) This feature automatically locks all vehicle doors when: • all doors are closed, • the engine is running, • you shift into any gear, putting the vehicle in motion, and • the vehicle’s speed is greater than 3 mph (5 km/h). Auto-relock The autolock feature repeats when: • a door is opened and closed while the engine is running, • you shift into any gear, putting the vehicle in motion, and • the vehicle’s speed is greater than 3 mph (5 km/h). Auto-unlock The auto-unlock feature will unlock all doors when: • the ignition has been in the 3 (ON) position, all doors are closed, and


the vehicle has been in motion at a speed greater than 12 mph (20 km/h),


• the vehicle has then come to a stop and the ignition is turned to the 2
• the driver door is opened {within ten minutes after the ignition was


(ACCESSORY) or 1 (OFF/LOCK) position, and


transitioned to the 2 (ACCESSORY) or 1 (OFF/LOCK) position}.


Note: The vehicle doors will not auto-unlock if the vehicle has been electronically locked prior to the driver door being opened. Deactivating/activating the autolock or auto-unlock feature Automatic door locks can also be turned on/off through the following procedure: You must complete Steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must


83


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


wait at least 30 seconds. Note: Before following the procedure, make sure that the ignition is in the 1 (OFF/LOCK) position and all vehicle doors, the hood, and the decklid are closed. 1. Turn the ignition to the 3 (ON) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (ON) to the 1 (OFF/LOCK) position. 4. Press the power door unlock control three times. 5. Turn the ignition back to the 3 (ON) position. 6. The door locks will lock/unlock to confirm programming mode is entered/active. 7. With the ignition still in the 3 (ON) position, for the autolock feature, press the unlock control once then press the lock control once. The horn will chirp once to confirm successful programming. For the auto-unlock feature, press the lock control once, then press the unlock control once. The horn will chirp once to confirm successful programming.


If any door, the hood, or the deck lid is open, the horn will chirp twice, and the procedure will need to be performed again.


8. After having waited the necessary time for the programming to confirm, turn the ignition to the 1 (OFF/LOCK) position. Once disabled, the autolock feature can be enabled by repeating the procedure in Steps 1–8.


84


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.


INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle. To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.


85


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


Keep vehicle doors and luggage compartment


locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.


On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high


temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.


REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The remote entry system allows you to lock or unlock all vehicle doors without a key.


The remote entry features operate with the ignition in any position, except in the 3 (ON) , with the transmission not in either P (Park) or N (Neutral). If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.


86


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


Unlocking the doors 1. Press lamps will illuminate. 2. Press


and release to unlock the driver’s door. Note: The interior


and release again within five seconds to unlock all the doors.


Locking the doors Press


once to lock all the doors. The doors will lock upon first press.


again within three seconds to receive confirmation that the


Press vehicle was successfully locked. Note: If all vehicle doors, the hood, and , the horn will the trunk are closed upon the second press of the chirp once and the parklamps/taillamps will flash once to confirm the successful locking. Upon the second press of the not securely closed the horn will chirp twice to warn that successfully locking was not complete. The park/taillamps will NOT flash if any door is ajar.


, if any door, the hood, or the trunk is


Opening the trunk Press • Ensure that the trunk is closed and latched before driving your


once to open the trunk.


vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’s rear view.


This feature will not work with a vehicle speed greater than 3 mph (5 km/h) if the ignition is in the 2 (ACCESSORY) or 3 (ON) position.


on the remote transmitter to activate the alarm. Note: The


Sounding a panic alarm Press panic alarm only works with the ignition in the 1 (OFF/LOCK) position. a second time to deactivate the alarm. You may also deactivate Press the alarm by turning the ignition to the 3 (ON) position.


Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.


87


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.


2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.


3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.


Replacing lost transmitters Take all your vehicle’s transmitters to your authorized dealer if service is required. If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your authorized dealer for


programming, or


88


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


• Perform the following programming procedure yourself: Note: Ensure the brake pedal is not depressed during this sequence. Place the key in the ignition and cycle from 1 (OFF/LOCK) to 3 (ON) eight times in rapid succession within 10 seconds. After doors lock/unlock, press any control on all transmitters (up to four). After pressing the control on each remote transmitter, the door will lock and unlock. If programming multiple remote transmitters, you must press the control buttons on each remote transmitter within 7 seconds of each other to remain in programming mode. When completed, turn the ignition to 1 (OFF/LOCK). All transmitters must be programmed at the same time. • When completed, turn the ignition to the 1 (OFF/LOCK) position and


wait at least 20 seconds in order to use the recently programmed transmitter(s).


• All transmitters must be programmed during the same programming


cycle. A transmitter that is not programmed within the same programming cycle will be erased and will no longer operate your vehicle’s locks. If this occurs, you will have to reprogram all the transmitters again, as you cannot just “add” a transmitter.


Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 2 (ACCESSORY), 3 (ON) or 4
• the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control must not be set to the off position for the illuminated entry system to operate.


(START) positions, or


89


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, or after 10 minutes if the last door is left open. Radio type approval numbers for remote entry receiver If the type approval of your remote entry system is inspected in one of the countries listed in the following table, refer to the corresponding approval number:


Remote entry receiver certification numbers


Gabon Jordan Zambia


01070305/ARTEL/GABTEL


CAZ/ENG/CA/04/11/1


TRC/LPD/2004/28


Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.


1 2


7 8


5 6


3 4


9 0


without using the key.


KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you can: • lock or unlock the vehicle doors • open the trunk. See also Remote entry system in this chapter for more information. Your vehicle has a factory-set 5–digit code that operates the keyless entry system. You can also program your own 5–digit personal entry code. The factory-set code is located: • On the owner’s wallet card in the glove compartment, or • At your dealer. When using the keyless entry keypad, press the middle of each button in order to ensure a good activation.


Programming a personal entry code You can program up to three personal codes to unlock your vehicle. These codes do not replace the permanent code that the authorized dealer gave you.


90


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


To create your own personal entry code: 1. Enter the factory set code. Note: The keypad will illuminate when pressed. 2. Within five seconds press 1 • 2 on the keypad to enter the programming mode. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. Press 1 • 2 to store the first personal code. 5. The doors will lock then unlock to confirm programming of the new code. To store a second personal code: 1. Enter the factory set code. 2. Within five seconds press 1 • 2 on the keypad to enter the programming mode. 3. Enter a second personal 5-digit code. Each number must be entered within five seconds of each other. 4. Press 3 • 4 to store the second personal code. 5. The doors will again lock then unlock to confirm programming of the new code. To store a third personal code: 1. Enter the factory set code. 2. Within five seconds press 1 • 2 on the keypad to enter the programming mode. 3. Enter a third personal 5-digit code. Each number must be entered within five seconds of each other. 4. Press 5 • 6 (or 7 • 8, or 9 • 0, or wait five seconds) to store the third personal code. 5. The doors will again lock then unlock to confirm programming of the new code. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal


code.


91


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


Erasing personal code To erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 2. Press and release 1 • 2 within 5 seconds of step 1. 3. Press and hold 1 • 2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure. Unlocking the doors and releasing the trunk with the keyless entry system To unlock the driver door, enter either the factory-set code or personal code (each digit pressed within 5 seconds of prior digit). The interior lamps will illuminate. • To unlock all doors, enter the factory-set code or personal code • To release the trunk, enter the factory-set code or personal code


(driver door unlocks) and press 3 • 4 within five seconds. (driver door unlocks) and press 5 • 6 within five seconds.


After the factory-set code or personal code has been entered, you can unlock all doors (press 3 • 4) and release the trunk (press 5 • 6) as long as the controls are pressed within 5 seconds of each other. Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. To lock the doors, press 7 • 8 and press 9 • 0 at the same time. Note: The doors will not lock if the driver door is ajar. Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the • the ignition is turned to the 3 (ON) position. SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition.


control on the remote entry transmitter.


92


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Radio type approval numbers for Immobiliser System PATS XCVR If the type approval of your immobilizer system is inspected in one of the countries listed in the following table, refer to the corresponding approval number:


Immobiliser System PATS XCVR certification numbers


TX Frequency: 134,2 kHz


Country Name


American Samoa (USA)


Bahrain Barbados Canada China Ghana


Guam (USA)


Jordan Kenya Kuwait Mauritius


Mayotte (F)


Mexico Morocco


Netherlands Antilles (NL)


Nicaragua


Northern Mariana Islands


Oman


Puerto Rico


Qatar


Saudi Arabia South Korea


-8,1 dBµA/m @ 10 m


Type Approval Number


See USA


DLM/GEN/18/18/16


340/3 Vol.II


CANADA: 3043104475A


CMII ID:2005DJ0428
SPLS / -485 / 2001


See USA 4/U/U/4250


CCK/ES/100/0


M.C/U.S.0 /5/7-12579


TA/2005/15


RLVVIVP03-324


MR 1299 ANRT 2004


NCG-CE-04-004


See USA


OMA/1265(A) 1308/2001


See USA


QTEL/SR/2003/R-276


(10/1900)


R-LPD1-04-0145


93


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


Immobiliser System PATS XCVR certification numbers


Tunisia


United Arabian Emirates


Uruguay


USA


Zambia


269/MAT/2004


5/10-2/3274/3774


025/FR/2003


NT8-15607PAT3XCVR CAZ/ENG/CA/2005/02/8


Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Your vehicle comes with two coded keys (or three, if your vehicle is equipped with the valet feature); additional coded keys may be purchased from your authorized dealer. The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition to the 1 (OFF/LOCK) position, remove all objects on the key chain away from the coded key and restart the engine.


Anti-theft indicator The anti-theft indicator is the flashing red indicator located on the dash panel. • When the ignition is in the 1 (OFF/LOCK) position, the indicator will


flash once every 2 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent.


• When the ignition is in the 3 (ON) position, the indicator will glow for


3 seconds to indicate normal system functionality.


If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for service.


94


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Automatic arming The vehicle is armed immediately after switching the ignition to the 1
(OFF/LOCK) position. The theft indicator on the instrument panel will flash every two seconds when the vehicle is armed.


Locks and Security


Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. • The theft indicator on the instrument panel will illuminate for three • If the theft indicator stays on for an extended period of time or


seconds and then go out.


flashes rapidly, have the system serviced by your authorized dealer.


Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.


Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock娂 keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your authorized dealer to have the spare coded key(s) programmed. Please read and understand the entire procedure before you begin.


95


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1
(OFF/LOCK) to the 3 (ON) position (maintain ignition in 3 (ON) for at least one second). 2. Turn ignition to 1 (OFF/LOCK) and remove the first coded key from the ignition. 3. Within ten seconds of removing the first coded key, insert the second previously programmed coded key into the ignition and turn the ignition from 1 (OFF/LOCK) to the 3
(ON) position (maintain ignition in 3 (ON) for at least one second but no more than ten seconds). 4. Turn the ignition to 1 (OFF/LOCK) and remove the second coded key from the ignition. 5. Within twenty seconds of removing the second coded key, insert the new unprogrammed key (new key) into the ignition and turn the ignition from 1 (OFF/LOCK) to the 3 (ON) position (maintain ignition in 3 (ON) for at least one second). This step will program your new key. 6. To program additional new unprogrammed key(s), wait at least 20
seconds and repeat this procedure from Step 1. If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will illuminate for three seconds and then go out. If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off. You may repeat Steps 1
through 6. If failure repeats, bring your vehicle to your authorized dealer to have the new spare key(s) programmed.


PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting.


Arming the system When armed, the perimeter alarm will notify you of an unauthorized entry. When unauthorized entry occurs, the system will flash the park lamps and will sound the horn.


96


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Locks and Security


The system is ready to arm whenever the key is out of the ignition. Any of the following actions will arm the alarm system: • Press the remote transmitter lock control one time to arm the system. • Lock all doors using the keypad. • Lock all doors using the interior power lock switch while the driver or


passenger door is open and then closed.


on the remote


If all the closures (doors, trunk, hood) are closed, the park lamps will flash once and the horn will chirp once when the entry transmitter is pressed a second time within five seconds. If any closure is not properly closed, the park lamps will not flash and the horn will chirp twice. The system will wait 20 seconds after one of the arming actions is performed before allowing the alarm to become armed. After the 20–second pre-arm phase, the interior trim remote trunk release control and the power door unlock control are disabled, in order to further protect your vehicle.


Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter. • Unlock the doors using a valid code on the keypad. • Unlock the doors with the key in the key lock cylinder. • Turn the ignition to the 3 (ON) position.


97


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


SEATING


Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints. The head restraints can be moved up and down.


Push control to lower head restraint.


Adjusting the front manual seat (if equipped)


Never adjust the driver’s seat or seatback when the vehicle is moving.


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


98


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Lift handle to move seat forward or backward.


Pull lever up to adjust seatback.


Before returning the seatback to its original


position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


Using the manual recline function (if equipped)


Never adjust the driver’s seat or seatback when the vehicle is moving.


Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the


event of a collision.


99


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


To adjust the front seatback using the manual recliner: • Lift and hold the handle located • Lean against the seatback to


on the side of the seat.


adjust it to your desired position. You can recline the seat back or bring it forward.


• Release the handle when the desired position has been reached.


Adjusting the power front seats – door mounted controls (if equipped) The controls for the power seats are located on the inside of each front door.


Never adjust the driver’s seat or seatback when the vehicle is moving.


Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the


event of a collision.


Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.


100


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system section for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.


Press the control to recline the seatback forward or backward.


Press to move the seat forward or backward.


101


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Press to move the front portion of the seat cushion up or down.


Press to move the rear portion of the seat cushion up or down.


Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness. Heated seats (if equipped) The heated seat control is located on the driver’s or front passenger’s door. To operate the heated seats: • Push the indicated side of the control for maximum heat. • Push again to deactivate.


102


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


• Push the indicated side of the control for minimum heat. • Push again to deactivate.


The heated seat module resets at every ignition run cycle. While the ignition is in the ON position, activating the high or low heated seat switch enables heating mode. When activated, they will turn off automatically when the ignition is turned to the OFF position. The indicator light will illuminate when the heated seats have been activated.


REAR SEATS


Seat mounted cup holders and armrest storage compartment (if equipped) Your vehicle may be equipped with cup holders in the rear seat armrest. To access the cup holders, fold the armrest down.


Use only soft cups in the cupholder. Hard objects can


injure you in a collision.


SAFETY RESTRAINTS


Personal Safety System姟 The Personal Safety System娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. Your vehicle’s Personal Safety System娂 consists of the following items: • Driver and passenger dual-stage airbag supplemental restraints


103


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints • Front safety belts with pretensioners, energy management retractors, and safety belt usage sensors • Driver’s seat position sensor • Front crash severity sensor • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp • Restraints Control Module (RCM) with impact and safing sensors • Restraint system warning light and back-up tone • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system, and indicator lights.


How does the Personal Safety System姟 work? The Personal Safety System娂 can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions. The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system. Rather, it means the Personal Safety System娂 determined the accident conditions (crash severity, belt usage, etc.) were not appropriate to activate these safety devices. Front airbags are designed to activate only in frontal and near-frontal collisions, not rollovers, side-impacts, or rear-impacts unless the collision causes sufficient longitudinal deceleration. Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy. A lower, less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag supplemental restraints section in this chapter. Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact. This


104


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


allows your Personal Safety System娂 to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System娂 to tailor the deployment level of the driver dual-stage airbag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front.


Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must


use a forward-facing child seat in the front seat, move the seat all the way back.


Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.


The front passenger sensing system can automatically turn off the front passenger airbag and passenger seat-mounted side airbag. The system is designed to help protect small (child size) occupants from frontal airbag deployments when they are seated or restrained in the front passenger seat contrary to proper child-seating or restraint usage recommendations. Even with this technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag when the passenger seat is empty. The sensor turns off the passenger seat-mounted side airbag (if equipped) when the seat is empty and the safety belt is unbuckled. When the front passenger seat is occupied and the sensing system has turned off the passenger’s frontal airbag, the “pass airbag off” indicator


105


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


will light and stay lit to remind you that the front passenger frontal airbag is off. See Front passenger sensing system in the airbags section of this chapter. Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System娂 to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter. Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions and in side collisions. This helps increase the effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can be activated alone or, if the collision is of sufficient severity, together with the front airbags. Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum. This helps reduce the risk of force-related injuries to the occupant’s chest by limiting the load on the occupant. Refer to Energy management feature section in this chapter. Determining if the Personal Safety System姟 is operational The Personal Safety System娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning light section in the Instrument cluster chapter. Routine maintenance of the Personal Safety System娂 is not required. The Restraints control module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, front passenger sensing system, and the driver seat position sensor. In addition, the RCM also monitors the restraints warning light in the instrument cluster. A difficulty with the system is indicated by one or more of the following. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition is


turned on.


106


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


• A series of five beeps will be heard. The tone pattern will repeat


periodically until the problem and warning light are repaired.


If any of these things happen, even intermittently, have the Personal Safety System娂 serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions


Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


To reduce the risk of injury, make sure children sit in the back seat where they can be properly restrained.


Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from


injury in a collision.


All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an airbag


supplemental restraint system (SRS) is provided.


It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas


are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.


In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.


Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that


are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.


107


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.


Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check


seat covers and buckles before you place a child anywhere near them.


Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.


2. To unfasten, push the release button and remove the tongue from the buckle.


Energy management feature • This vehicle has a safety belt system with an energy management


feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • The energy management feature is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.


108


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Lap belts


Adjusting the front center seat lap belt (if equipped)


The lap belt should fit snugly and as low as possible around the hips, not across the waist.


The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.


Shorten and fasten the belt when not in use. The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts. The front outboard passenger and rear seat safety belts have three types of locking modes described as follows:


Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.


109


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and prevents more belt from being pulled out if the belt is pulled out too quickly. The belt will unlock when you stop pulling on it.


Automatic locking mode In this mode, the shoulder belt is pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Any time a child safety seat, except a booster, is installed in a


passenger front outboard or any rear seating position. Children 12
years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter.


How to use the automatic locking mode • Buckle the combination lap and


shoulder belt.


110


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


• Grasp the shoulder portion and pull downward until the entire belt is pulled out.


• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.


How to disengage the automatic locking mode


Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an


authorized dealer after any collision to verify that the ⬙automatic locking retractor⬙ feature for child seats is still working properly. Safety belt assemblies should be inspected by an authorized dealer and must be replaced if either damage or improper operation is noted. Failure to replace the belt and retractor assembly could increase the risk of injury in a collision.


Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.


Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.


Do not use extensions to change the fit of the shoulder belt across the torso.


111


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front outboard passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, push the button and slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.


Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety


belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.


Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.


Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe


personal injuries in the event of a collision.


For proper care of soiled safety belts, refer to Interior in the Cleaning chapter.


112


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.


Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...


Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.


The safety belt warning light and warning chime turn off.


The safety belt warning light and indicator chime remain off.


Belt-Minder姞 The Belt-Minder威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning light in the instrument cluster when the driver’s and front passenger’s safety belt is unbuckled. The Belt-Minder威 feature uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the Belt-Minder威 feature for objects placed in the front passenger seat, warnings will only be given to large front seat occupants as determined by the front passenger sensing system. Both the driver’s and passenger’s safety belt usages are monitored and either may activate the Belt-Minder威 feature. The warnings are the same for the driver and the front passenger. If the Belt-Minder威 warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder威 feature.


113


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Then... The Belt-Minder威 feature will not activate.


If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph (5 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...


The Belt-Minder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until the safety belts are buckled. The Belt-Minder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until the safety belts are buckled.


The driver’s or front passenger’s safety belt becomes unbuckled for approximately 1 minute while the vehicle is traveling at least 3 mph (5 km/h) and more than 1-2
minutes have elapsed since the ignition switch has been turned to ON... The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events”


36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 miles (40 km)


of home.


114


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Reasons given... Consider... “Belts are uncomfortable”


We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.


“I was in a hurry” Prime time for an accident. Belt-Minder威


“Safety belts don’t work”


“Traffic is light”


“Belts wrinkle my clothes”


“The people I’m with don’t wear belts”


reminds us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.


“I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40
times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.


“I’d rather be thrown clear”


Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder威 chime. To do so may


adversely affect the performance of the vehicle’s air bag system.


115


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


One time disable If at any time the driver/front passenger quickly buckles then unbuckles the safety belt for that seating position, the Belt-Minder威 is disabled for the current ignition cycle. The Belt-Minder威 feature will enable during the same ignition cycle if the occupant buckles and remains buckled for approximately 30 seconds. Confirmation is not given for the one time disable. Deactivating/activating the Belt-Minder姞 feature The driver and front passenger Belt-Minder威 are deactivated/activated independently. When deactivating/activating one seating position, do not buckle the other position as this will terminate the process. Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. Note: The driver and front passenger Belt-Minder威 features must be disabled/enabled separately. Both cannot be disable/enabled during the same key cycle. The driver and front passenger Belt-Minder威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled


While the design allows you to deactivate your Belt-Minder威, this system is designed to improve your chances of being safely


belted and surviving an accident. We recommend you leave the Belt-Minder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the Belt-Minder威 feature while driving the vehicle.


1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1
minute) • Step 3 must be completed within 50 seconds after the safety belt


warning light turns off.


116


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.) • After Step 3, the restraint system warning light (airbag light) will be


turned on for three seconds.


4. Within approximately 7 seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder威 feature for that seating position if it


is currently enabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds.


• This will enable the Belt-Minder威 feature for that seating position if it


is currently disabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds, followed by 3
seconds with the light off, then followed by the restraint system warning light flashing 4 times per second for 3 seconds again.


AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)


117


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.


All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag


supplemental restraint system (SRS) is provided.


Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.


The National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm)


between an occupant’s chest and the driver airbag module.


Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.


Ford Motor Company recommends that an authorized dealer inspect all steering column assemblies in use in vehicles involved


in a collision. Failure to inspect and if necessary replace the steering column assembly could result in severe injury or death in the event of a collision.


Do not attempt to service, repair, or modify the steering column, its adaptive module, or its fuses. See your authorized dealer.


118


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the • Recline the seat slightly one or two degrees from the upright position.


pedals comfortably.


Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those


objects to be propelled by the air bag into your face and torso causing serious injury.


Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. See your authorized


dealer.


The front passenger airbag is not designed to offer protection to an occupant in the center front seating position.


Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow


hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.


119


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.


Airbags can kill or injure a child in a child seat.


NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.


How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Driver and passenger airbags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts unless the collision causes sufficient longitudinal deceleration.


120


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions, swelling or temporary hearing loss. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. The SRS consists of the following items: • Driver and passenger airbag modules (which include the inflators and • safety belt pretensioners • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to • Driver and passenger side airbags (if equipped) • One or more impact and safing sensors • A readiness light and tone • A diagnostic module • The electrical wiring which connects the components


Front passenger sensing system. later in this chapter.


airbags)


121


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


The diagnostic module monitors its own internal circuits as well as the supplemental airbag electrical system wiring (including the impact sensors), the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors.


Several air bag system components get hot after inflation. Do not touch them after inflation.


If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not


replaced, the unrepaired area will increase the risk of injury in a collision.


If the safety belt pretensioners deploy in an accident, they will not function again ( belt will not extract or retract) and must be


replaced immediately. Failure to replace the retractor assemblies will increase the risk of injury.


Front passenger sensing system The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor Vehicle Safety Standard (FMVSS) 208
and is designed to disable (will not inflate) the front passenger’s frontal airbag under certain conditions. The front passenger sensing system works with sensors that are part of the front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or disabled (will not inflate). The front passenger sensing system will disable (will not inflate) the front passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in • the system determines that an infant is present in a rear-facing infant • the system determines that a small child is present in a forward-facing


seat that is installed according to the manufacturer’s instructions,


the front seat,


child restraint that is installed according to the manufacturer’s instructions,


• the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period of


time,


122


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing system uses a ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located on the instrument panel to the right of the radio over the glove box. Note: The indicator lamp will illuminate for a short period of time when the ignition is turned to the ON position to confirm it is functional. When the front passenger seat is not occupied (empty seat) or in the event that the front passenger frontal airbag is enabled (may inflate), the indicator lamp will be unlit. The front passenger sensing system is designed to disable (will not inflate) the front passenger’s frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the indicator lamp will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. • If the child restraint has been installed and the indicator lamp is not


lit, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer’s instructions.


The front passenger sensing system is designed to enable (may inflate) the front passenger’s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat. • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’s seat, but the ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the • Have the person sit upright in the seat, centered on the seat cushion,


full upright position.


with the person’s legs comfortably extended.


123


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag. • If the indicator lamp remains lit even after this, the person should be


advised to ride in the rear seat.


Occupant


Empty seat Small child in child safety seat or booster Small child with safety belt buckled or unbuckled Adult


Pass Airbag Off Indicator Lamp Unlit Lit


Lit


Unlit


Passenger Airbag


Disabled Disabled


Disabled


Enabled


Even with Advanced Restraints Systems, children 12 and under should be properly restrained in the back seat.


After all occupants have adjusted their seats and put on safety belts, it’s very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.


Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the


decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.


The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below.


124


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Objects


Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e. heavy briefcase, fully packed luggage) Empty seat, or small to medium object with safety belt buckled


Pass Airbag Off Indicator Lamp Unlit


Passenger Airbag Disabled


Lit


Lit


Disabled


Disabled


equipped)


If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • Objects lodged underneath the seat • Objects between the seat cushion and the center console (if • Objects hanging off the seat back • Objects stowed in the seatback map pocket (if equipped) • Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above.


To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or


hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag Status. Failure to follow these instructions may interfere with the front passenger seat sensing system.


125


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If objects are lodged and/or cargo is interfering with the seat; please take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver and/or adult passengers should check for any objects lodged • Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least 2 minutes and verify that the airbag readiness lamp is no • If the airbag readiness lamp remains illuminated, this may or may/not


underneath the front passenger seat or cargo interfering with the seat.


longer illuminated


be a problem due to the front passenger sensing system.


DO NOT attempt to repair or service the system; take your vehicle immediately to an authorized dealer.


The front passenger airbag is not designed to offer protection to an occupant in the center seating position.


An out of position front center occupant could affect the decision of the front passenger sensing system.


If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide.


Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system.


126


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either • The readiness light will not illuminate immediately after ignition is turned on.


flash or stay lit.


• A series of five beeps will be heard. The tone pattern will repeat


periodically until the problem and/or light are repaired.


If any of these things happen, even intermittently, have the SRS serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.


Seat-mounted side airbag system (if equipped)


Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.


Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and


increase the risk of injury in an accident.


Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback.


Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your


authorized dealer.


127


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.


How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. The side airbag system consists of the following: • An inflatable nylon bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.


for the front airbags.


• A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnostic unit as used • Two crash sensors located near the side of the vehicle. Side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side airbags are designed


128


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration.


Several air bag system components get hot after inflation. Do not touch them after inflation.


If the side airbag has deployed, the airbag will


not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.


Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either • The readiness light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat


flash or stay lit.


turned on.


periodically until the problem and/or light are repaired.


If any of these things happen, even intermittently, have the SRS serviced at your authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.


Disposal of airbags and airbag equipped vehicles (including pretensioners) See your authorized dealer. Airbags MUST BE disposed of by qualified personnel.


129


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children. Many states require that children use approved booster seats until they are eight years old. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle. When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.


Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from


injury in a collision.


Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.


Do not leave children, unreliable adults, or pets unattended in your vehicle.


Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder


130


2007 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Seating and Safety Restraints


belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury in a crash. To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably. Booster seats may also make the shoulder belt fit

Loading...
x