Download PDF Manual

— — — — — — — Blue — Pink Green Red Yellow Brown Black


Fuse rating


2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A


Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.


187


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


27


18


25


16


26


17


23


14


24


15


21


12


22


13


19


10


20


11


Relay


33


31


29


32


30


28


Passenger Compartment Fuse


Panel Description


Taxi, Cluster, Lighting Control Module (Interior Lighting) Ignition (ON) - Electronic Automatic Temperature Control (EATC) module, A/C mode switch (vehicles equipped with EATC only) EATC module (vehicles equipped with EATC only) Audio (base audio system on vehicles not equipped with EATC) Ignition (ON) - Anti-lock Brake System (ABS) module, Positive Crankcase Ventilation (PCV) Speed control deactivation switch, Stop signal, Brake-Transmission Shift Interlock (BTSI) (column-shift transmission)


The fuses are coded as follows.


Fuse/Relay Location


Fuse Amp


Rating


15A


10A


10A


10A


10A


188


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Fuse/Relay Location


Fuse Amp


Rating


Passenger Compartment Fuse


Panel Description


10


11


12


13
14


15


16
17
18


10A 10A


10A


20A


5A


10A


10A


10A 10A


7.5A


15A 10A 10A


Ignition (ON) - Cluster LCM (Park lamps, Switch illumination) Ignition (ON) - Rear Air Suspension Module (RASM), Variable Assist POwer Steering (VAPS) LCM (Headlamps, Cornering lamps) Ignition (ON/START) - Driver’s Door Module (DDM), Police PDB (Police vehicles only) Ignition (START) - ON/ACC (window) relay coil (non-Police vehicles only) Ignition (START) - ON/ACC (window and decklid) relay coil and Police ON/ACC relay coil (Police vehicles only) Ignition (ON/START) - Starter relay coil, DTRS Ignition (START) - Wiper module Ignition (ON) - BTSI (Floor-shift transmission) Ignition (START) - LCM, Door lock switch illumination, Heated seat switch illumination, Moonroof, Overhead console, Electrochromatic mirror Ignition (ON) - Turn signals Ignition (START) - Audio Ignition (ON) - A/C mode switch (manual A/C only), Blend door, DDM, Heated seat modules, Daytime Running Lamps (DRL) module


189


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Passenger Compartment Fuse


Panel Description


Left-hand low beam, DRL Ignition (ON/ACC) - Back-up lamps Right-hand low beam, DRL Ignition (ON/ACC) - Restraint Control Module (RCM), Occupant Classification Sensor (OCS), Passenger Air bag Deactivation Indicator (PADI) Multi-function switch (Flash-to-pass) Ignition (ON/ACC) - Passive Anti-Theft System (PATS) module, Powertrain Control Module (PCM) relay coil, Fuel relay coil, Ignition coil relay coil Autolamp/Sunload sensor, Power mirrors, Door lock switches (DDM), Adjustable pedal switch Ignition (ON/ACC) - Analog cluster, Warning lamp module, LCM, Overdrive cancel switch, Rear defroster relay coil Cigar lighter, OBD II, Power point Center High-Mounted Stop Lamp (CHMSL) Audio Stop lamps, MFS Hazards (non-Police vehicles) Hazards (Police vehicles) Mirror heaters, Rear defroster switch indicator Fire suppression module (if equipped) (Police vehicles only) Rear defroster


Roadside Emergencies


Fuse/Relay Location


Fuse Amp


Rating


19
20


21
22


23


24


25


26


27
28


29
30
31


32


33


10A 10A


10A 10A


15A


10A


10A


10A


20A 10A


15A 15A 15A 20A 10A


10A


Relay 1


Full ISO relay


190


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.


Always disconnect the battery before servicing high current fuses.


To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or


refilling fluid reservoirs.


If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.


503


502


501


24


23


22


20


21


19


304


209


206


208


205


207


301


303


302


204


203


202


201


602


601


118


114


110


106


102


117


113


109


105


101


116


112


108


104


115


111


107


103


18


16


14


12


10


17


15


13


11


The high-current fuses are coded as follows.


191


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Fuse/Relay Location


10
11
12


13
14
15
16


17
18
19
20
21
22
23
24
101


Fuse Amp


Rating 20A*


25A*


10A*


20A* 10A*


15A* 30A* 20A*


15A* 20A* 15A* 25A*


20A* 20A* 20A* 20A*


— —


15A* 15A* 15A*


— — 5A* 40A**


Power Distribution Box Description Ignition switch (Key in, RUN 1, RUN 2) Ignition switch (RUN/START, RUN/ACC, START) Powertrain Control Module (PCM) keep alive power Fuel relay feed Rear Air Suspension Module (RASM), VAPS module Alternator regulator PCM relay feed Driver’s Door Module (DDM), Door locks Ignition coil relay feed Horn relay feed A/C clutch relay feed Audio (non-Police vehicles only) Tray lamps (Police vehicles only) Instrument panel power point Stop lamp switch Heated seats Daytime Running Lamps (DRL) module Not used Not used Injectors PCM, Mass Air Flow (MAF) sensor Powertrain loads and sensors Not used Not used Radio mute Blower relay feed


192


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Fuse/Relay Location


102
103


104


105
106


107
108


109
110
111


112


113


114


115


116


117


Fuse Amp


Rating 50A** 50A**


40A**


30A** 40A**


40A** 20A**


20A** 30A** 50A**


30A**


40A**


50A**


50A**


50A**


50A**


50A**


Roadside Emergencies


Power Distribution Box Description Cooling fan Instrument panel (I/P) fuse box feed #1, I/P fuses 23, 25, 27 and 31
Instrument panel (I/P) fuse box feed #2, I/P fuses 1, 3, 5, 7 and 9
Starter relay feed Anti-lock Brake System (ABS) module (Pump) Rear defroster relay feed Moonroof (non-Police vehicles only) Spotlights (available on Police vehicles, Long Wheel Base [LWB] vehicles and commercial vehicles only) ABS module (Valves) Wiper module Police PDB or Police I/P accessory battery feed (Police vehicles only) Air suspension compressor (non-Police vehicles only) Police PDB relay feed (Police vehicles only) Police light bar or Police Trunk accessory battery feed (Police vehicles only) Police PDB or Police I/P accessory battery feed (Police vehicles only) Rear power point or Police trunk accessory battery feed (Police vehicles only) Police I/P accessory battery feed (Police vehicles only) Police PDB or Police I/P accessory battery feed (Police vehicles only)


193


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Fuse/Relay Location


118


201
202
203
204
205
206
207
208
209
301
302


303
304


501
502
503
601


602


Fuse Amp


Rating 50A**


1⁄2 ISO relay



1⁄2 ISO relay 1⁄2 ISO relay



1⁄2 ISO relay


— —


Power Distribution Box Description Rear power point or Police trunk accessory battery feed (Police vehicles only) A/C clutch Not used Ignition coil PCM Not used Fuel Not used Not used Horn Starter


only) RUN/ACC relay (Police vehicles only)


1⁄2 ISO relay Full ISO relay Full ISO relay Air compressor (non-Police vehicles


Full ISO relay Blower Full ISO relay RUN/ACC relay (windows) (non-police vehicles only) RUN/ACC relay (windows and decklid) (police vehicles only) A/C clutch PCM Horn, Door latch Power seats, Lumbar, Decklid


Diode Diode Diode


20A Circuit


breaker


20A Circuit


breaker


RUN/ACC relay (windows) (non-police vehicles only) RUN/ACC relay feed (windows and decklid) (police vehicles only)


* Mini fuse ** Cartridge fuse


194


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Relays Relays are located in the power distribution box and should be replaced by qualified technicians.


JUMP STARTING YOUR VEHICLE


The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or


vehicle damage.


Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.


Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter.


Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off.


195


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Connecting the jumper cables


+–


+–


1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.


+–


+–


2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.


196


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


+–


+–


3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.


+–


+–


4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.


Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an


explosion of the gases that surround the battery.


5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.


Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle.


197


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.


Removing the jumper cables


+–


+–


Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.


+–


+–


2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.


198


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


+–


+–


3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.


+–


+–


4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.


199


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


WRECKER TOWING


If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Before your vehicle can be towed, the air suspension control in the luggage compartment must be turned to the OFF position (if equipped). If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.


200


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


GETTING THE SERVICES YOU NEED


At home You must take your Ford vehicle to an authorized Ford dealer for warranty repairs. While any Ford dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the dealership. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford. If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. 3. If you require assistance or clarification on Ford Motor Company policies or procedures, please contact the Ford Customer Relationship Center at 1-800-392-3673 (FORD).


Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) www.customersaskford.com


201


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
1-800-521-4140
(TDD for the hearing impaired: 1-800-232-5952) www.customersaskford.com In Canada: Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-387-9333
www.lincolncanada.com In order to help you service your Lincoln vehicle, please have the following information available when contacting the Lincoln Centre: • Your telephone number (home and business) • The name of the dealer and the city where the dealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) Additional Assistance If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.).


202


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.


IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126


203


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company


vehicles.


The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.


What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance concerns as on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: • a non-Ford product • a non-Ford dealership • sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’s performance as designed


maintenance and wear items)


service or product concern is being reviewed


• a request for reimbursement of consequential expenses unless a • items not covered by the New Vehicle Limited Warranty (including • alleged personal injury/property damage claims • cases currently in litigation • vehicles not used primarily for family, personal or household purposes (except in states where the Dispute Settlement Board is required to review commercial vehicles)


• vehicles with non-U.S. warranties Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the unique brochures for California, West Virginia, Georgia and Wisconsin purchasers/lessees.


204


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form. Some states will require you to use certified mail, with return receipt requested. Your application is reviewed and, if it is determined to be eligible, you will receive an acknowledgment indicating: • The file number assigned to your application. • The toll-free phone number of the DSB’s independent administrator. Your dealership and a Ford Motor Company representative will then be asked to submit statements. To properly review your case, the Board needs the following information: • Legible copies of all documents and maintenance or repair orders • The year, make, model, and Vehicle Identification Number (VIN) listed • The date of repair(s) and mileage at the time of occurrence(s). • The current mileage. • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor • The names (if known) of all the people you contacted at the • A description of the action you expect to resolve your concern. You will receive a letter of explanation if your application does not qualify for Board review.


on your vehicle ownership license.


relevant to the case.


dealership(s).


Company.


205


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well. Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board. Since the Board generally meets once a month, it may take longer for the Board to consider some cases. After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.


To request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call the Board at the following address/phone number: Dispute Settlement Board P.O. Box 1424
Waukesha, WI 53187–1424
1–800–428–3718
You may also contact the North American Customer Relationship Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952
or by writing to the Center at the following address: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, Michigan 48121


UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealerships. In those cases where you continue to feel that the efforts by Ford of Canada and the


206


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.


FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. It provides the following: • Benefits during the warranty period depending on the plan you


purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).


• Protection against covered repair costs after your Bumper-to-Bumper


Warranty expires.


You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 4,600 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this


207


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.


GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Worldwide Direct Market Operations.


ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207


208


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


Or call: For a free publication catalog, order toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.)


Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.


REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C. area) or write to: NHTSA 400 Seventh Street U.S. Department of Transportation Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from the Hotline.


209


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing


strong, direct sunlight.


or laundry liquid. These products can discolor and spot painted surfaces.


• Never wash a vehicle that is “hot to the touch” or during exposure to • Always use a clean sponge or car wash mitt with plenty of water for • Dry the vehicle with a chamois or soft terry cloth towel in order to • It is especially important to wash the vehicle regularly during the


eliminate water spotting.


best results.


winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppings


and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. • Remove any exterior accessories, such as antennas, before entering a • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.


car wash.


WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid Wax (ZC-53-A), which is available from your dealer, or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.


PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your dealer to ensure you get the correct color.


210


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Cleaning • Remove particles such as bird droppings, tree sap, insect deposits, tar • Always read the instructions before using the products.


spots, road salt and industrial fallout before repairing paint chips.


ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft Wheel and Tire Cleaner (ZC-37–A),


covers.


which is available from your dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water.


• Never apply any cleaning chemical to hot or warm wheel rims or • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.


• Do not use hydrofluoric acid-based or high caustic-based wheel • To remove tar and grease, use Motorcraft Bug and Tar Remover


cleaners, steel wool, fuels or strong household detergent.


(ZC-42), available from your dealer.


ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts


engine block or other engine components.


that require cleaning and pressure rinse clean.


211


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


• Cover the highlighted areas to prevent water damage when cleaning • Never wash or rinse the engine while it is running; water in the


the engine.


running engine may cause internal damage.


PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar


Remover (ZC-42).


WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, tree sap, or other organic contamination. To clean these items, please follow these tips: • The windshield, rear windows and side windows may be cleaned with


a non-abrasive cleaner such as Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23), available from your dealer.


212


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or


windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly.


Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines.


INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, dry cloth, or use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Avoid cleaners or polish that increase the gloss of the upper portion of


the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.


Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of


the air bag system. • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces.


INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, dry • Do not use household or glass cleaners as these may damage the


cloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A).


finish.


INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional Strength • If grease or tar is present on the material, spot-clean the area first


Carpet & Upholstery Cleaner (ZC-54).


with Motorcraft Spot and Stain Remover (ZC-14).


213


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Cleaning • If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.


immediately (but do not oversaturate) or the ring will set.


Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing.


Do not use chemical solvents or strong detergents when cleaning the seat-mounted side air bag. Such products could contaminate the side air bag system and affect performance of the side air bag in a collision.


Cleaner (ZC-11–A). Dry the area with a soft cloth.


LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl • To help maintain its resiliency and color, use the Motorcraft Deluxe Leather Care Kit (ZC-11–D), available from your authorized dealer. • Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear, protective coating.


Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining.


UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.


FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your


214


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Car Care Kit (ZC-26) Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail Wash (ZC-3–A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft One Step Wash and Wax Concentrate (ZC-6-A) Motorcraft Paint Sealant (ZC-45) Motorcraft Premium Car Wash Concentrate (U.S. only) (ZC-17-B) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Liquid Wax (ZC-53-A) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft Tire Clean and Shine (ZC-28) Motorcraft Triple Clean (U.S. only) (ZC-13) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Vinyl Cleaner (Canada only) (CXC-93) Motorcraft Vinyl Conditioner (Canada only) (CXC-94) Motorcraft Wheel and Tire Cleaner (ZC-37–A)


215


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy • We provide scheduled maintenance information which makes


location.


tracking routine service easy.


If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft parts are designed and built to provide the best performance in your vehicle.


Notice to owners of Severe Duty vehicles Before you have maintenance done on your vehicle, be sure to read the “Severe Duty Owner’s Guide Supplement.” This book contains important operation and maintenance information.


PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed • Keep all open flames and other burning (cigarettes) material away


space, unless you are sure you have enough ventilation.


from the battery and all fuel related parts.


Working with the engine off 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels.


Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.


216


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3. Lift the hood until the lift cylinders hold it open.


IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT


4.6L SOHC V8 engine


1. Brake fluid reservoir 2. Engine oil dipstick 3. Windshield washer fluid reservoir 4. Air filter assembly


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


217


Maintenance and Specifications


5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Power distribution box 9. Engine oil filler cap 10. Automatic transmission fluid dipstick


WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter.


State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.


If you operate your vehicle in temperatures below 40° F (4.5°C), use washer fluid with antifreeze protection. Failure to use


washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.


Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components.


ENGINE OIL


Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground.


218


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


2. Turn the engine off and wait up to 10 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).


6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this


range, the oil level is acceptable. DO NOT ADD OIL.


• If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.


219


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter.


• Do not overfill the engine


with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician.


7. Put the indicator back in and ensure it is fully seated.


Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal operating range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise until three clicks can be heard. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.


220


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Engine oil and filter recommendations Look for this certification trademark.


Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine. Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.


221


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.


However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to scheduled maintenance information for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells. If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.


Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted


substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.


222


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps,


resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.


Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.


Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.


Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Release the parking brake. With your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.


relearn the idle and fuel trim strategy.


If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected.


223


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.


RECYCLE


ENGINE COOLANT


Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060). The level of coolant should be maintained at the “FULL COLD” level or within the “COLD FILL RANGE” in the coolant reservoir. If the level falls below, add coolant per the instructions in the Adding engine coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265°F (129°C). • Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly.


224


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


When the engine is cold, check the level of the engine coolant in the reservoir.


• The engine coolant should be at the “FULL COLD” level or within the


“COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).


• Refer to scheduled maintenance information for service interval • Be sure to read and understand Precautions when servicing your


schedules.


vehicle in this chapter.


If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.


Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained.


225


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.


Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could


make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant


(yellow-colored), VC-7–A (U.S., except CA, OR and NM), VC-7–B (CA, OR and NM), meeting Ford Specification WSS-M97B51–A1.


Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, VC-2 and VC-3
(US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection.


• A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing. • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.


• Do not add extra inhibitors or additives to the coolant. These


can be harmful and compromise the corrosion protection of the engine coolant.


For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “FULL COLD” level. For all other vehicles which have a


226


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.


To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The


cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.


1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (a translucent plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” or the “FULL COLD” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. Turn until tightly installed. (Cap must be tightly installed to prevent coolant loss.) After any coolant has been added, check the coolant concentration (refer to Checking engine coolant). If the concentration is not 50/50
(protection to –34° F/–36° C), drain some coolant and adjust the concentration. It may take several drains and additions to obtain a 50/50
coolant concentration. Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quart (1.0 liter) of engine coolant per month, have your dealer check the engine cooling system. Your cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage.


Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.


227


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Used engine coolant should be disposed of in an appropriate


manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.


Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this section. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section.


Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentration • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will


above 50%.


decrease the overheat protection characteristics of the engine coolant and may cause engine damage.


• Refer to the chart on the coolant container to ensure the


coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.


above 40%.


If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will


decrease the corrosion protection characteristics of the engine coolant and may cause engine damage.


• Decreased engine coolant concentrations below 40% will


decrease the freeze protection characteristics of the engine coolant and may cause engine damage.


• Refer to the chart on the coolant container to ensure the


coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.


Vehicles driven year-round in non-extreme climates should use a 50/50
mixture of engine coolant and distilled water for optimum cooling system and engine protection.


228


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works • Standard Cluster


• Optional Cluster


TEMP


If the engine begins to overheat: • The engine coolant temperature gauge will move to the H (hot) area • The engine coolant temperature gauge will illuminate all eight bars


(if your vehicle if equipped with analog gauges).


and a tone will sound every five seconds for one minute (if your vehicle is equipped with digital gauges).


• The Check Engine indicator light will illuminate. • The If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However:


symbol will illuminate.


229


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down, causing steering and braking


effort to increase.


Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to a service facility. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low.


Never remove the coolant reservoir cap while the engine is running or hot.


5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible.


WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS


Important safety precautions


Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.


The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops


before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.


230


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.


Automotive fuels can cause serious injury or death if misused or mishandled.


Gasoline may contain benzene, which is a cancer-causing agent.


Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials


and any open flames before refueling your vehicle.


• Always turn off the vehicle before • Automotive fuels can be harmful


refueling.


or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind


can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.


• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.


• Fuels can also be harmful if absorbed through the skin. If fuel is


splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is


231


2005 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.


When refueling always shut the engine off and never allow

Loading...
x