Login- Download PDF Manual
-
(1.6 km/h) by a momentary tap of the SET-ACCEL switch. Multiple taps of the SET-ACCEL switch will increase your vehicle speed 1 mph (1.6 km/h) for each tap. For example, if you are currently set at 60 mph (96 km/h) and tap the SET-ACCEL switch 5
times your vehicle speed will increase and set at 65 mph (104 km/h).Turning the Speed Control Off
You can cancel the speed control while you are driving. q Press the OFF switch. The speed control is off. If you want to resume speed control, press the ON switch and reset the speed control by pressing the SET ACCEL button. q Press the clutch pedal slightly (if equipped). The speed control is suspended, but you can reset it by pressing SET ACCEL or return to the previous set speed with the RESUME switch.
q Press the brake pedal slightly. The speed
control is suspended, but you can reset it by pressing SET ACCEL or return to the previous set speed with the RESUME switch.
In addition, the speed control is turned off each time you turn the vehicle off.
115
File:ltscb.ex Update:Fri Jun 9 15:29:08 1995
*[SC11100( ALL)11/89] *[SC11200( ALL)05/95]
*[SC11250( ALL)03/93]
*[SC11400( ALL)12/91]
Driving uphill or on a steep grade
When the speed control is on, your vehicle may significantly drop speed when driving uphill, especially with a heavy load. If the speed drops more than 8 to 14 mph (15 - 25 km/h) the automatic speed control will, by design, be canceled. You may have to temporarily resume manual speed control while driving up a steep grade in order to maintain the speed you desire.
Frequent shifting of an automatic transmission or speed loss during speed control operation can be eliminated by shifting out of overdrive into drive (or by pressing the Transmission Control Switch, if equipped). These conditions could occur in hilly terrain or at higher elevations.
If the speed control “dropped out” after your climb is completed, the speed of your vehicle can be reset with the SET ACCEL switch, or returned to the previous set speed with the RESUME switch, as long as you are driving over 30 mph (48 km/h).
116
File:ltscb.ex Update:Fri Jun 9 15:29:08 1995
%*[SC11500( ALL)03/95] *[SC11600( ALL)07/94]
*[SC11700( ALL)05/95] *[SC11800( ALL)11/94]
*[SC11850( ALL)03/95]
Cancelling and Resuming a Set Speed If you press the brake pedal, the speed control is cancelled. You can return to the speed you set by using the RSM switch, as long as you did not press the OFF switch. To resume the speed you had before, you must be driving at least 30 mph (50 km/h). Press and release the RESUME switch. Your vehicle gradually returns to the previously set speed and then maintains it.
RWARNING
If your vehicle has speed control, do not use it on slippery roads. You could lose control of your vehicle and could injure someone.
117
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV00401(BEF )02/95]
*[FV00601(BEF )01/95] %*[FV01801(BEF )03/95] *[FV01901(BEF )10/89]
*[FV06001(B F )05/90] [FV06101(B )05/90]
[FV06201(B )05/90]
[FV06300(B )05/90]
*[FV06601(B F )05/90]
Features
Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features. Doors Anti-theft front door lock knobs
Anti-theft lock knobs are designed to preclude unlocking the door by pulling up on the bullet type lock knob. To unlock and open the front door from the inside of the vehicle, pull on the inside door handle. Tailgate
To open the tailgate, first lower the tailgate window.
Next, lift the latch handle from the inside tailgate panel of your vehicle, and lower the tailgate.
To close the tailgate, lift it and push forward with enough force to latch the assembly securely in position.
When open, the tailgate load should not exceed 500 lbs (227 kgs). If you want to load heavy items onto your vehicle, Ford recommends that you load them one at a time, directly on the bed floor to avoid damage to the tailgate or its supports.
119
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV06701(B )05/90]
[FV06801(B )05/90]
one third page art:0020193-B
[FV06901(B )05/90]
[FV07001(B )05/90]
[FV07101(B )05/90]
For trucks with a swing away spare tire carrier, you must release the carrier and swing it out of the way before lowering the tailgate. See the following illustration.
Bronco tailgate operation
Latch lockout system for the tailgate
The tailgate is equipped with a latch lockout system which prevents you from opening it unless the glass is completely down. The lockout also prevents the glass from being raised unless the tailgate is completely latched in the closed position.
RWARNING
When driving your vehicle make sure that the tailgate door and window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out.
120
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV07201(B )02/92]
[FV07301(B )03/95]
[FV07401(B )02/92]
[FV07501(B )02/92]
*[FV14100(BEF )04/95] *[FV14500(BEF )05/95]
*[FV14701(BEF )03/91]
*[FV15001(BEF )05/95]
quarter page art:0020203-C
*[FV15301(BEF )02/95]
*[FV15401(BEF )06/94]
If you must drive with the rear window open: q Adjust your climate control system to force
outside air into your vehicle.
q Completely open the outside air vents if your
vehicle is so equipped.
q You can prevent the tailgate from accidentally
opening by raising the glass one inch from the fully opened position.
Power Door Locks (If equipped)
The power door lock switches are located in the front doors. To lock all doors push the switch marked L. To unlock all doors push the switch marked U.
The manual door locks will override the power door lock controls.
Power door lock controls Remote Entry System (If equipped) If your vehicle has the remote entry system, you can lock or unlock the vehicle doors without using a key. The remote also has a personal alarm feature. The buttons for the system are located on the two hand held transmitters that came with your vehicle.
121
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV15600(BEF )02/95]
*[FV15700(BEF )02/95]
*[FV15800(BEF )04/94]
quarter page art:0020788-A
%*[FV15901(BEF )02/95]
*[FV16001(BEF )02/95]
*[FV16101(BEF )02/95]
*[FV16300(BEF )02/95]
[FV16500(B F )04/95] *[FV16600(B F )03/93]
%*[FV16800(BEF )02/95] *[FV16900(BEF )04/95]
The system will work with up to four transmitters. Your vehicle came with two transmitters. Additional transmitters can be ordered from your dealer. The remote entry features only operate with the ignition in the OFF position.
The remote entry transmitter
Unlocking the doors with the remote entry system To unlock the driver’s door, press the UNLOCK button. To unlock the other doors, press the UNLOCK button a second time within five (5) seconds of unlocking the driver’s door. Locking the doors with the remote entry system To lock all the doors, press the LOCK button. If you would like a signal that the doors are being locked, press the LOCK button again within five seconds. The door will lock again, the horn will beep, and the external lamps will flash. Remote entry personal alarm If you wish to activate the remote entry system personal alarm, press the PANIC button. This will honk the horn and flash the lights for
122
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV17000(BEF )02/95]
*[FV17100(BEF )04/94]
quarter page art:0060566-B
%*[FV17501(BEF )02/95] *[FV17601(BEF )02/95]
*[FV17701(BEF )02/95]
approximately 2 minutes 45 seconds. You can turn it OFF by pressing the PANIC button again from the same transmitter or by turning the ignition to the ON or ACCESSORY position.
When you use the remote entry UNLOCK or PANIC buttons, the illuminated entry system turns on the vehicle’s interior lights for 25
seconds. You can turn these lights off with the remote entry LOCK button or by turning the ignition to the ON or ACCESSORY position.Replacing the batteries
The remote entry transmitter is powered by two coin type three-volt lithium 2016
batteries (included) that should last for several years of normal use. If you notice a significant decrease in operating range, the batteries should be replaced. Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer.NOTE: The operating range of the remote
entry system can also be affected by weather conditions (such as very cold temperatures) or structures around the vehicle (buildings, other vehicles, radio and TV towers, etc.). Typical operating range will allow you to be up to 33
feet (10 meters) away from your vehicle.123
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV17801(BEF )03/93]
quarter page art:0020789-A
*[FV17901(BEF )02/95]
*[FV18001(BEF )02/95]
quarter page art:0020790-A
%*[FV18101(BEF )02/95] *[FV18200(BEF )02/95]
Opening the remote transmitter
The transmitter can be snapped apart to replace the batteries by twisting a thin coin between the two halves of the transmitter. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. When installing the new batteries, be sure to place the positive (+) side down as marked. Snap the two halves back together.
Replacing the batteries
Replacing lost transmitters
In the event a transmitter is lost, you should take all your vehicle’s transmitters to your dealer to have the remote entry system deprogrammed for the lost transmitter. This is necessary to prevent further unauthorized use of the lost transmitter.
124
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV18301(BEF )02/95]
*[FV18601(BEF )04/95] [FV18701(BEF )04/95]
*[FV18801(BEF )04/94]
*[FV18900(B F )04/94]
*[FV19000(B F )03/95]
*[FV19102(B F )03/95]
You can also purchase additional transmitters (up to 4 transmitters can be used) from your dealer. You will need to take all your transmitters to the dealer so they can program them to the remote entry system all at the same time. Illuminated Entry System (If equipped)
This system will provide illumination of the vehicle’s interior courtesy lamps when either outside front door handle is pulled or when the Remote Entry System is used to unlock the door or sound the Personal Alarm. The system will automatically turn off after approximately 25
seconds or when the ignition is turned to the START or ACCESSORY position.NOTE: The inside lights will not turn off if
you have turned them on with the dimmer knob or if any door is open.
Battery Saver (with Remote Entry — If equipped)
When the ignition is turned off, the vehicle will turn off battery voltage to all of these lights after 40 minutes: glove box, engine compartment, overhead console, mirror, courtesy and interior (including cargo) lamps.
This will prevent draining of the battery if these lights have been left on inadvertently or if a door is not completely closed. Battery voltage to these lamps will be restored when the remote entry transmitter is used, any door is opened, or the ignition key is turned on again.
125
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV19250(BEF )02/95] [FV22000(B )05/90]
[FV22101(B )05/91]
[FV22201(B )05/90]
[FV22301(B )02/92]
[FV22401(B )03/95]
[FV22501(B )02/92]
[FV22601(B )02/92]
Windows Tailgate Window
The switch to operate the tailgate window is on the instrument panel to the left of the steering column next to the master lighting switch. With the ignition in the ON or ACC position, move the switch down to lower the window and move it up to raise the window. You can also operate the tailgate window by using the key from the outside of the tailgate.
RWARNING
When driving your vehicle make sure that the tailgate door and window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out.
If you must drive with the rear window open: q Adjust your climate control system to force
outside air into your vehicle.
q Completely open the outside air vents if your
vehicle is so equipped.
q You can prevent the tailgate from accidentally
opening by raising the glass one inch from the fully opened position.
126
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV22701(B )03/91]
quarter page art:0020215-B
[FV22801(B )02/89]
*[FV22901(BEF )03/91] *[FV23001(BEF )05/90]
*[FV23501(BEF )05/95]
*[FV23800(BEF )05/95]
quarter page art:0020203-C
Rear window switch
When driving in extremely dusty areas, clean the tailgate glass periodically to prevent build-up of surface dust. This will prevent excessive wear or damage to the tailgate window seals. Using the Power Windows (If equipped)
Each door has a power control that opens and closes the window on that door. The driver’s door has a master control switch that operates both front door windows. You must place the ignition switch in the ON or ACC position to use your power window controls.
RWARNING
Do not let children play with the power windows. They may seriously hurt themselves. Make sure occupants are clear of the window(s) before closing.
Master control switch
127
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV24101(BEF )01/95] *[FV24801(BEF )05/90] *[FV24901(BEF )08/94] *[FV25001(BEF )08/94]
*[FV25101(BEF )10/89] *[FV25201(BEF )04/95] *[FV25301(BEF )04/89]
*[FV25600(B F )03/91]
one third page art:0020218-B
*[FV25700(B F )05/95]
one third page art:0020220-E
Seats Adjusting the Front Seat Manually To move the front seat forward or rearward: 1. Find the adjustment lever at the lower left
corner of the front seat.
2. Push the lever to the left to unlatch the seat. 3. Move the seat to the desired position. 4. Release the lever to latch the seat in its new position. Make sure the seat locks securely in place.
Adjusting bucket seat
Adjusting the bench seat
128
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV26001(BEF )05/95]
*[FV26100(BEF )05/95]
*[FV26200(BEF )05/95]
*[FV26300(BEF )05/95]
*[FV26400(BEF )10/89] *[FV27301(BEF )02/92]
*[FV27401(B F )03/93]
*[FV27501(BEF )10/89]
*[FV27601(BEF )10/89]
*[FV27701(BEF )10/89]
RWARNING
Never adjust the driver’s seat or seatback when the vehicle is moving.
RWARNING
Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
RWARNING
To reduce the risk of serious injury in a collision, always drive and ride with your seatback upright and the lap belt snug and low across the hips.
RWARNING
To reduce the risk of serious injury in a collision, children should always ride with the seatback upright.
Reclining Bucket Seats
You can tilt the seat back of your bucket seats backward.
1. On the outboard side of the seat, lift the recliner handle up and hold it in place.
2. Lean against the back of the seat and adjust
it to the position you want.
3. Release the handle to lock the seat back in
place.
4. To return the seat back upright, lift the
handle and lean forward.
129
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV27800(B F )02/92]
one third page art:0020222-B
*[FV28001(B F )10/90]
*[FV30501(B F )01/89] [FV30801(B )12/91]
[FV31000(B )05/95]
one third page art:0020227-D
Reclining bucket seat
Lifting the seat-back adjustment lever of an unoccupied seat will allow the seat back to fold forward for access to the rear. Pushing the seat back backward with the handle released returns the seat upright. Seat Back Release (Bench Seat)
The split back bench seat can be folded forward on either side to gain access to the rear of the vehicle. To do so, push up the latch button located at the top of the seat back.
Seat back release
130
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV31101(B F )05/95]
[FV43500(B )01/89]
[FV43600(B )01/89]
[FV43700(B )01/89]
[FV43800(B )03/90]
[FV43900(B )03/90]
[FV44000(B )03/90]
[FV44100(B )12/89]
[FV44200(B )01/89]
[FV44300(B )01/89]
[FV44400(B )01/89]
[FV44500(B )05/90]
RWARNING
A seatback which is folded forward even a small degree may not lock properly in the event of a sudden stop or collision.
Rear Flip Fold Seat
To fold the seat forward:
1. The seat back latch is at the lower rear right hand side of the seat. Lift the latch handle to unlock the seat back.
2. Fold the seat back over the seat cushion
until it locks into place.
3. Unlock the seat from the floor striker by
lifting the seat latch handle at the center rear edge of the seat.
4. Lift the seat and fold forward.
To remove and reinstall the rear flip-fold seat:
1. Remove the torque rod by releasing it from
the right hand floor bracket (by pushing forward and up).
2. Remove the pin spring retainers and the pins
from both the floor brackets.
3. Remove the seat assembly from your Bronco.
Reverse this procedure to install the rear flip-fold seat.
NOTE: It is important that you do not damage the seat belt hardware while removing or installing the rear flip-fold seat.
131
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV44600(B )01/89]
half page art:0020238-A
*[FV45901(B F )05/93] *[FV46020(B F )05/93]
*[FV46025(B F )05/94] *[FV46030(B F )05/93]
*[FV46035(B F )03/93]
*[FV46043(B F )08/94]
Assembly for installing and removing the rear seat Tilt Slide Seat With the seatback tilted forward, the tilt slide seat can be moved forward to provide additional entry space to access the rear seat compartment of the vehicle. To operate the tilt slide seat: 1. Lift the seatback release lever on the
outboard side of the seat cushion to unlock the slide mechanism and the seatback.
2. Push the seat assembly forward to provide entry space to the rear seat compartment of the vehicle.
RWARNING
Do not place objects behind or under the front seat which can prevent the seat from returning to the locked position.
132
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV46045(B F )05/93] *[FV46051(B F )05/93]
*[FV46053(B F )10/94]
*[FV46055(B F )07/94]
one third page art:0021018-B
*[FV46065(B F )05/95]
*[FV46070(B F )07/94]
one third page art:0021019-B
Relocking the seat after a tilt slide operation:
3. Push the seat backrest to its upright latched position. Continue to push the seat rearward to return it to its latched position. (This can be done from inside the rear seat compartment or from outside the vehicle.)
NOTE: The seat can no longer be moved
rearward when in its latched position.
Prior to operating the vehicle, check to ensure that the seat assembly is locked by pushing or pulling the seat forward or rearward. If seat does not lock, repeat steps 2 and 3.
133
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV46075(B F )03/93] *[FV46080(B F )05/93]
*[FV46085(B F )07/94]
one third page art:0021020-B
*[FV47000(BEF )03/94]
*[FV47400(BEF )12/91]
*[FV47500(BEF )06/92]
quarter page art:0020860-B
To operate the seat adjuster:
4. To adjust the seats forward or rearward, locate the release lever at the right lower front area of the seat cushion. Move the release lever to the right and hold until the desired seat position is obtained, then release the lever to relock the seat.
Using the Power Lumbar Support and Side Bolsters
If your vehicle is equipped with this option, you can inflate a lumbar support pad in the seat back. To inflate the lumbar pad, push the (+) side of the rocker switch. To deflate push the (-) side of the switch.
Power lumbar switch
134
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV47600(BEF )04/95] *[FV47620(BEF )05/95] *[FV47625(BEF )05/95]
*[FV47630(BEF )04/95]
*[FV47640(BEF )04/95] *[FV47650(BEF )04/95]
*[FV47660(BEF )04/95]
*[FV50000(BEF )01/95] *[FV50200(BEF )03/91]
*[FV50325(BEF )05/95]
Cleaning the Seats
Leather and vinyl
For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a leather and vinyl cleaner or a mild soap.
Wipe the surface with a damp, soft cloth, then dry and buff with a dry, soft cloth.
Fabric
Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Follow the directions that come with the cleaner.
NOTE: Before using any cleaner, test it on a
small, hidden area of fabric. If the fabric’s color or texture is adversely affected by a particular cleaner, do not use it.
Mirrors With the door closed and the seat adjusted for comfort and proper vehicle control, move the mirrors for best view by tilting up or down, left or right. Do not adjust the mirrors while the vehicle is in motion.
RWARNING
Make sure you can see clearly through the rearview mirror at all times. Do not allow anything to block your vision. If you can’t see through the mirror, you could be involved in an accident and injure yourself or others.
135
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
%*[FV50700(B F )01/95]
*[FV50850(B F )03/93]
half page art:0021008-A
*[FV50900(B F )03/93]
*[FV51050(B F )03/94]
Automatic Dimming Inside Rearview Mirror (If equipped)
Automatic dimming inside rearview mirror
This mirror is equipped with an electrochromic glare control feature that automatically darkens the mirror, reducing glare from the headlamps of vehicles behind you. A forward facing light sensor measures the ambient light just as your eyes do. When the rear facing light sensor in the glass senses glare, such as from following headlights, it energizes a chemical layer in the glass causing it to darken and absorb light. As the glare subsides, the mirror glass returns to its normal clear state.
To turn the mirror on, push the On/Off switch, located on the bottom of the mirror, to latch it in the ON position. The button will be latched in the up position and at night a low intensity green light will be visible from the button when the mirror is turned on. To turn the mirror off,
136
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV51100(B F )03/93]
*[FV51200(B F )03/94]
*[FV51400(B F )03/93]
*[FV51500(B F )01/95]
*[FV52900(BEF )12/89] *[FV53000(BEF )10/89]
*[FV53100(BEF )03/95]
push the On/Off switch again and the button will unlatch shutting off the light and the mirror will be off.
Demonstration — The mirror’s operation may be demonstrated by simulating glare as follows:
1. Cover the forward facing sensor, located on
the right side of the mirror back, with a dark (preferably black) cloth. Hold the dark cloth over the sensor until you notice the mirror glass start to darken to the non-glare state. If the surrounding lighting conditions are too dark it may be necessary to shine additional lighting, such as from a flashlight, on the rearward sensor located on the glass face.
2. Remove the cloth (and shut off the flashlight if applicable) and the glass will return to the clear reflective stage.
One important safety feature is that the mirror automatically returns to the normal position whenever the vehicle is placed in R (Reverse) (when the mirror is in the ON position). This feature ensures a bright clear view in the mirror when backing up. Outside Mirrors (Manual Control)
Adjust outside mirrors with the door closed and the seat adjusted for comfort and proper vehicle control. Move the mirrors for best view by tilting up or down, left or right.
On vehicles equipped with fold-away mirrors, the mirrors should be folded rearward into the body position before entering automatic car wash systems.
137
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV53300(B F )12/91]
quarter page art:0020900-B
[FV53800(B )05/90]
quarter page art:0020324-B
*[FV54000(B )12/91]
*[FV54400(BEF )05/95]
Standard fold-away mirror
Low-mount swingaway mirror
The right-hand side view mirror is convex. This mirror has a curved surface and will show a wider view of the lane next to and behind your vehicle.
RWARNING
The side view mirror on the right makes objects appear smaller and farther away than they actually are.
138
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV54500(BEF )08/91]
*[FV54600(BEF )08/91] *[FV54800(BEF )06/94]
*[FV55000(BEF )06/94]
*[FV55200(BEF )06/94]
*[FV55400(BEF )06/94]
*[FV55700(B F )12/91]
quarter page art:0020886-A
*[FV55900(BEF )12/91]
Dual Electric Remote Control Mirrors (If equipped)
To adjust the remote controlled side mirrors:
1. Find the control switch in the driver’s door
panel.
2. Select the right or left mirror by moving the
selector switch to R or L.
3. Move the control knob in the direction you
want to move the mirror.
4. Return the selector switch to the middle
position to keep the mirror in place.
Power mirror control
Do not clean the plastic housing of any electric mirror with gasoline or other petroleum-based cleaning products.
139
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV59400(BEF )01/95] *[FV59500(BEF )12/91]
*[FV60100(B F )12/91]
half page art:0020683-C
Console Your vehicle may have a full console. The full console has the features shown in the illustration below.
The features on the console
140
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV60200(B F )12/91]
three fourths page art:0020909-A
Seat mounted console
141
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV60350(B )03/93]
[FV60450(B )05/95]
*[FV60500(B )03/93] *[FV60600(B )03/93] *[FV60700(B )03/93] *[FV60800(B )03/93] *[FV60900(B )05/95]
*[FV60920(B )03/93]
*[FV60940(B )03/93] *[FV60960(B )03/93] *[FV60980(B )03/93] [FV61001(B )05/95]
quarter page art:0020980-B
[FV61100(B )03/93] *[FV61150(B )05/95]
Overhead Console (Eddie Bauer only) Your Eddie Bauer Bronco comes with an overhead console located between the sun visors. The console includes: q Compass/temperature display q Map lamps
Storage compartment
Compass/Temperature display
This display provides the outside temperature and the compass direction of the vehicle.
The MODE button is used to select one of the following features: q Display Off q Temp in ˚F and Compass q Temp in ˚C and Compass
Compass/temperature display
Outside temperature display
If the outside temperature is below 39˚F (4˚C), the word “ICE” will flash in the display alternately with the outside temperature for about one minute.
142
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV61400(B )05/95]
[FV61500(B )03/93] *[FV61600(B )01/95]
*[FV61700(B )05/95]
[FV61800(B )03/93] *[FV61900(B )05/95]
[FV62050(B )05/95] *[FV62100(B )03/93]
Electronic Compass
Factors affecting compass accuracy
The compass reading can be affected when you drive near a number of things — such as large buildings, bridges, power lines, and powerful antennas.
Your compass can also be affected by magnetic or metallic objects placed in or on the vehicle. If the compass is giving inaccurate readings, perform the following compass adjustments.
Compass adjustments
There are two possible adjustments to the compass: Zone and Calibration.
Zone adjustment
1. Determine which zone of the country you
are in by referring to the following zone map.
143
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV62200(B )03/93]
half page art:0080142-C
*[FV62300(B )03/93]
*[FV62400(B )03/93]
*[FV62500(B )03/93]
*[FV62600(B )03/93]
*[FV62700(B )05/95]
Zone map
2. Press and hold the “MODE” button until the
“VAR” indicator appears in the display (approximately 4 seconds).
3. Release the “MODE” button. The display
will now show the current zone number that is stored in the compass.
4. Press the “MODE” button repeatedly (or press and hold in) until the desired zone number appears in the display (once it reaches 15, the next press of the button will set it to 1).
5. Release the “MODE” button when the
desired zone number is displayed.
After approximately three seconds the display will flash all segments and then return to normal operation. Zone is now updated.
144
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
[FV62850(B )05/95] *[FV62900(B )03/93]
*[FV63000(B )03/93]
*[FV63050(B )05/95]
*[FV63100(B )03/93] *[FV63300(B )03/93]
*[FV63800(B )03/93] *[FV63900(B )03/93]
[FV64050(B )05/94]
one third page art:0021077-B
Calibration adjustment
1. Find an open area that is free from steel
structures and high voltage lines. An open parking lot is a good example.
2. Press and hold the “MODE” button until the
“CAL” indicator appears in the display (approximately 8 seconds).
NOTE: You cannot perform calibration unless
the display reads “CAL.”
3. Release the “MODE” button.
4. Once the “CAL” indicator has appeared,
drive the vehicle slowly (less than 3 mph / 5 km/h) in 360˚ circles until the “CAL” indicator turns off. This will happen within 2
to 3 complete circles.Map lamps
The map lamps are located in the overhead console. The driver and passenger side each has its own switch.
Map lamps — Eddie Bauer only
145
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV64100(B )03/93] *[FV64200(B )03/93]
*[FV64300(B )03/93]
*[FV64400(B )03/93] *[FV64500(B )03/93]
*[FV64600(B )03/93] *[FV64700(B )03/93]
[FV64850(B )05/93]
one third page art:0021079-A
Storage Compartment
The storage compartment can be accessed by pushing the “OPEN” button. The door will open approximately one inch then it can be manually moved to the full open position.
The compartment can be used to store a variety of items such as: tissues, parking pass, cigarettes or sunglasses.
Use as Garage Door Opener
The door can be converted from “Utility” storage to a housing and means of actuating a variety of “aftermarket” garage door opener transmitters.
Removal of storage clip
In order to convert the door, simply remove the utility storage clip from the back side of the door as shown in the following illustration.
146
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV64900(B )03/93] *[FV65000(B )03/93]
*[FV65100(B )03/93]
*[FV65200(B )03/93]
[FV65350(B )05/93]
one third page art:0021080-A
Installing “aftermarket” transmitter Place the piece of Velcro hook onto your aftermarket transmitter, opposite side as that of the actuator button. Place the transmitter into the console housing, button down, as shown. Place the height adapters provided into the back side of the “GARAGE” button as needed. Some larger transmitters will not need the adapters, and some smaller ones may need two adapters. The transmitter can now be activated without opening the door. Simply depress the “GARAGE” button.
147
File:ltfvb.ex Update:Fri Jun 9 15:28:41 1995
*[FV69900(BEF )03/95] *[FV70000(B F )05/94]
*[FV70200(BEF )06/92] *[FV70300(B F )06/92]
quarter page art:0020929-A
Power Point Electrical Outlet The power point outlet is located on the instrument panel to the right of the shift lever. This outlet should be used in place of the cigarette lighter for optional electrical accessories. NOTE: Do not use the cigarette lighter in
place of the power point.
*[FV70500(B F )07/92]
Power point electrical outlet To access the outlet, lift up the hinged cover.
148
f
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS01200(BEF )04/95] *[AS01250(BEF )05/95]
*[AS01300(BEF )04/95]
*[AS01400(BEF )04/95]
*[AS01500(BEF )04/95] *[AS01600(BEF )04/95]
*[AS01625(BEF )04/95] *[AS01650(BEF )05/95]
*[AS01675(BEF )04/95]
*[AS01700(BEF )04/95] *[AS01800(BEF )04/95]
Compact Disc Radio The Compact Disc Radio combines the Electronic Stereo Radio with the Ford Compact Disc Player. Using the Controls on Your New Radio/CD Player Most of the features of this unit work for both radio and CD operation. Also, some of the knobs and buttons control several different functions, so be sure to read all of the operating instructions carefully. How to turn the radio on and off Press the “POWER” button to turn the radio on. Press it again to turn it off. How to adjust the volume Press the (+/–) side of the “VOL” button to increase/decrease the volume. Bars illuminate in the display to show the relative volume level. NOTE: If the volume level is set above a
certain listening level when the ignition switch is turned off, when the ignition switch is turned back on, the volume will come back to a “nominal” listening level. However, if the radio power is turned off (with the “POWER” button), the volume will remain in the position it was set at when radio power is switched back on.
Selecting the AM or FM frequency band Push the “AM/FM” button to select the desired frequency band. When in the radio mode, pushing the button more than once will alternate between AM, FM1 and FM2. These functions are used with the station memory buttons described under How to tune radio stations.
150
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
%*[AS01900(BEF )05/95] *[AS02000(BEF )07/94]
*[AS02100(BEF )04/95]
*[AS02200(BEF )04/95]
*[AS02300(BEF )04/95]
How to tune radio stations
There are four ways for you to tune in a particular station. You can manually locate the station using the “SCAN/TUNE” button, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency. These four methods are described below. q Using the “SCAN/TUNE” button to manually
tune
You can change the frequency up or down one increment at a time (FM changes in increments of 200kHz; AM changes in increments of 10kHz) by first pressing the “SCAN/TUNE” button twice (display shows “TUNE”), then — within approximately five seconds —pressing and releasing either the top a or bottom b half of the “SEEK” button. To change frequencies quickly, press and hold down either the top or bottom half of the “SEEK” button. While you are manually tuning, the display will show a blinking “M”.
Manual tuning adjusts your radio to any allowable broadcast frequency, whether or not a station is present on that frequency. (See All About Radio Frequencies in this section.)
151
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS02400(BEF )04/95] *[AS02500(BEF )04/95]
*[AS02600(BEF )04/95]
*[AS02700(BEF )04/95]
*[AS02800(BEF )04/95]
*[AS03000(BEF )04/95] *[AS03100(BEF )04/95]
*[AS03200(BEF )04/95]
q Using the “SEEK” function
This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the top a half of the “SEEK” button to select the next listenable station up the frequency band. Press the bottom b half of the button to select the next listenable station down the frequency band. By pressing and holding the button, listenable stations can be passed over to reach the desired station.
q Using the “SCAN/TUNE” button to scan
radio stations
Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the top a half of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately five seconds. Pushing the bottom b half of the “SEEK” button will begin the scan mode down the frequency band, again stopping on each listenable station for approximately five seconds.
To stop the scan mode on the presently sampled station press the “SCAN/TUNE” button again.
Setting the Station Memory Preset buttons
Your radio is equipped with 5 station memory buttons. These buttons can be used to select up to 5 preset AM stations and 10 FM stations (5 in FM1 and 5 in FM2). Follow the easy steps below to set these buttons to the desired frequencies.
1. Select a band, then select a frequency.
152
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS03400(BEF )04/95]
*[AS03500(BEF )04/95]
*[AS03510(BEF )04/95]
*[AS03520(BEF )04/95] *[AS03530(BEF )04/95]
*[AS03800(BEF )05/95]
*[AS03900(BEF )05/95]
2. Press one of the memory buttons and hold
the button until the sound returns. That station is now held in memory on that button.
3. Follow the two steps above for each station
memory preset button you want to set.
NOTE: If the vehicle’s battery is disconnected,
the clock and station memory preset buttons (if programmed in auto mode) will need to be reset.
q Using the Automatic Memory Load feature
You can activate the Auto Memory Load feature by pressing and holding the “AUTO PRESET” button for approximately three seconds. Auto Memory Load sets all memory buttons in AM, FM1 and FM2 sequentially by seeking out the first five strong stations for the respective band and storing them in memory buttons 1-5. (FM2 will store the second set of strong stations from the FM band.) With Auto Memory Store, you can continually set strong stations into your memory buttons without losing your existing memory presets, which is especially handy while traveling. Your radio will automatically set your memory buttons to the strong local stations so you don’t have to continually manually tune to existing stations. Activate Auto Memory Store by pushing the “AUTO PRESET” button once. Your radio will set the first five strong stations of the band you are in (AM, FM1 or FM2) into the memory buttons. The display will show “AUTO”, then run through the frequencies, stopping momentarily on the stations being set into the memory buttons. The radio is
153
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS04000(BEF )05/95]
*[AS04100(BEF )05/95]
*[AS04200(BEF )04/95]
*[AS04400(BEF )04/95]
*[AS04500(BEF )04/95] *[AS04600(BEF )04/95]
*[AS04700(BEF )04/95] *[AS04800(BEF )04/95]
now in the “AUTO” mode and this display will show “AUTO” each time a preset is activated.
NOTE: If there are fewer than five strong stations in the frequency band, the remaining unfilled buttons will store the last strong station detected on the band.
After all stations have been filled, the radio will begin playing the station stored on memory button 1.
To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET” button. Display will show “AUTO” then “OFF”. The next time Auto Memory Store is activated on that band, the radio will store the next set of five strong stations.
Using the “AUDIO” button to adjust the tone balance and speaker output
Increasing or decreasing bass response
Push the “AUDIO” button repeatedly until the display reads “BASS.” Push the “+” side of the “VOL” button to increase bass (more “lows”), and push the “-” side to decrease bass (less “lows”).
Increasing or decreasing treble response
Push the “AUDIO” button repeatedly until the display reads “TREB.” Push the “+” side of the “VOL” button to increase treble (more “highs”), and push the “-” side to decrease treble (less “highs”).
154
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS05050(BEF )04/95] *[AS05100(BEF )04/95]
*[AS05150(BEF )04/95] *[AS05200(BEF )04/95]
*[AS05250(BEF )04/95]
*[AS05300(BEF )04/95] *[AS05350(BEF )04/95]
q Adjusting speaker balance
Balance control allows you to adjust the sound distribution between the right and left speakers. Push the “AUDIO” button repeatedly until the display reads “BAL.” Push the “+” side of the “VOL” button to shift the sound to the right speakers, and push the “-” side to shift the sound to the left speakers.
q Adjusting speaker fader
Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the “+” side of the “VOL” button to shift the sound to the front speakers, and push the “-” side to shift the sound to the rear speakers.
NOTE: Illuminated bars in the display show relative levels of bass and treble and positions of speaker balance and fader functions after adjustments are made, then revert to volume level set.
Clock operation
When in the radio mode, push the “CLOCK” button to switch from radio frequency to clock. Only the clock numerals will be displayed in the clock mode — there is no A.M./P.M. indication. When in the clock mode, the time will be displayed until the button is pushed again. However, if you retune the radio while it is in the clock mode, the new radio frequency will be displayed for approximately ten seconds and then change back to clock.
155
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS05400(BEF )04/95]
*[AS05425(BEF )07/93]
*[AS05450(BEF )04/95]
*[AS06050(BEF )04/95]
*[AS06150(BEF )04/95]
*[AS06200(BEF )04/95]
*[AS06250(BEF )04/95]
When in the CD mode, push the “CLOCK” button to change the display from elapsed time mode to track number mode to clock mode. If the CD track selection is changed when you are in the clock or elapsed time mode, the new track number will be displayed for approximately ten seconds and then revert back to the previous mode.
The clock can also be viewed with the ignition off. Push the “CLOCK” button and the time will be displayed momentarily.
To set the clock, simultaneously press the “CLOCK” button and either the bottom (b) half of the “SEEK” button to set hours, or the top (a) half of the “SEEK” button to set minutes. Using the Controls on Your New Compact Disc Player
Your new Ford Compact Disc Player is capable of playing 12 cm or 8 cm discs, without an adapter! The Player operates when the power is on and a disc is inserted (label side up). Handle the disc by its edge only. (Be sure to read and follow all of the care and cleaning instructions under How To Take Care of and Clean Your CD Player and Discs.
NOTE: If after you insert a disc, the disc is
ejected and “ERROR” begins scrolling in the display, remove the disc and reinsert it right side up (label side up).
The digital display on your CD player will either show the track (selection) number or the elapsed time. (The display mode can be selected by pressing the “CLOCK” button.) Indicators for play (a), stop (X) and compression on (“C”) are also in the display. (These features are described later.)
156
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS06300(BEF )04/95] *[AS06350(BEF )04/95]
*[AS06400(BEF )04/95] *[AS06450(BEF )04/95]
*[AS06500(BEF )04/95]
*[AS06550(BEF )04/95]
*[AS06600(BEF )04/95]
*[AS06650(BEF )04/95] *[AS06700(BEF )04/95]
Once a disc is inserted, operation of the CD player will override that of the radio. NOTE: The volume, bass, treble, balance and
fader controls on the radio are also used with the CD player. Refer to earlier operating instructions on these controls.
How to insert a disc and begin play Insert one disc, label side up into the disc opening. When inserted, the disc automatically loads into the unit and play starts at the beginning of the first track (selection). When the disc reaches the end, the disc player automatically returns to the beginning of the disc and resumes playing. NOTE: Once a disc is inserted, the disc
opening is secured to prevent the accidental insertion of a second disc.
NOTE: The CD player has heat protection
circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “TOO HOT” will scroll in the display for approximately five seconds (radio will resume playing). When the temperature returns to normal operating range, the CD player will again be operational.
How to stop and restart the CD player When a disc is loaded, the unit automatically enters the play mode and the play indicator a illuminates. To stop temporarily, press the “PLAY/STOP” button or the “AM/FM” button. The stop indicator X in the display illuminates and operation returns to the radio mode. To resume CD play, press the “PLAY/STOP” button once again.
157
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS06750(BEF )04/95]
*[AS06760(BEF )04/95] *[AS06765(BEF )04/95]
*[AS06770(BEF )05/95]
*[AS06775(BEF )05/95]
*[AS06800(BEF )05/95]
*[AS06850(BEF )05/95]
*[AS06900(BEF )04/95]
NOTE: If the ignition key is turned OFF
during play and then is set to the ON or ACCESSORY position, the CD player will resume playing in the mode it was in when ignition was turned off.
Using the “SEEK” feature
The “SEEK” feature allows you to quickly find a particular selection on the disc.
Press the bottom (b) half of the “SEEK” button once to repeat the current playing selection. Press the top (a) half of the “SEEK” button to advance to the next selection.
Pressing and holding the bottom (b) or top (a) half of the “SEEK” button will scroll backward and forward respectively through the tracks.
How to fast forward or reverse your CD player
To quickly search for a particular point in a selection, press the “FF” button (to fast forward) or the “REV” button (to reverse). While either button is pressed, the disc goes forward or backward at two different speeds depending on how long the button is held down. (Pressing either button for more than approximately three seconds will speed up the process.) Release the button at the desired point (found by watching the elapsed playing time in the display or by listening to the sound during fast forward or reverse). When you have reached the beginning of track 1, the CD player will begin playing.
When you have reached the end of the disc by keeping the fast forward button pressed, the display will show “END” and the player will go into pause mode. Push the “PLAY/STOP” button to begin playing the first track of the disc, press the “REV” button to back up from
158
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS07000(BEF )04/95] *[AS07050(BEF )04/95]
*[AS07100(BEF )04/95] *[AS07150(BEF )04/95] *[AS07200(BEF )04/95]
*[AS07250(BEF )04/95]
*[AS07300(BEF )04/95] *[AS07350(BEF )04/95]
*[AS07400(BEF )04/95] *[AS07500(BEF )04/95]
the end of the disc, or use the “SEEK” function to locate a desired track. Using the “SCAN” function Press the “SCAN/TUNE” button to enter the scan mode. Once in the scan mode, press the top (a) or bottom (b) half of the “SEEK” button to scan forward or reverse, respectively. The CD player will begin scanning the disc, stopping on each listenable track for approximately eight seconds. This continues until you press the “SCAN/TUNE” button a second time. While in the scan mode, the display shows the current sampled track number. Special features of your CD player q Compression
The compression feature will bring soft and loud passages closer together for a more consistent listening level. To turn the compression on, press the “COMP” button. When on, the compression indicator (“C”) will appear in the display. Press the button again to turn off.
q Automatic Disc Storage
If the disc is ejected from the CD player but is not removed from the disc opening within approximately 10 seconds, the player will automatically reload the disc for storage, unless the disc is automatically ejected due to a “focus error” (disc inserted upside down). In this case, the disc will not be automatically reloaded.
How to eject the disc Push the “EJECT” button to stop play, eject the disc and resume radio operation of your audio system.
159
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS07600(BEF )04/95]
%*[AS08100(BEF )04/95]
*[AS08200(BEF )04/95]
*[AS08300(BEF )04/95]
*[AS08400(BEF )04/95]
*[AS08500(BEF )04/95]
*[AS08600(BEF )04/95]
*[AS08700(BEF )04/95] *[AS08800(BEF )04/95]
*[AS08900(BEF )04/95]
NOTE: You can eject the disc while the radio
power and/or ignition is on or off.
How To Take Care of and Clean Your CD Player and Discs
To ensure the continued performance of your Ford Compact Disc Player, carefully read the following precautions: q Always handle the disc by its edge. Never
touch the playing surface.
q Before playing, inspect the disc for any
contamination. If needed, clean the disc with an approved disc cleaner, such as the Discwasher쑓 Compact Disc Cleaner or the Allsop 3쑓 Compact Disc Cleaner, by wiping from the center out to the edges. Do not use a circular motion to clean.
q Do not clean discs with solvents such as benzine, thinner, commercially available cleaners or antistatic spray intended for analog records.
q Do not expose the disc to direct sunlight or
heat sources such as defroster and floor heating ducts. Do not leave any discs in a parked car in direct sunlight where there may be a considerable rise in temperature or damage may result.
q After playing, store the disc in its case.
If a disc has already been inserted, do not try to insert another disc. Doing so may damage the disc player.
q Do not insert anything other than a disc into
the disc player.
160
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS09000(BEF )04/95]
*[AS09100(BEF )04/95]
*[AS09200(BEF )04/95]
*[AS09300(BEF )04/95] *[AS09400(BEF )04/95]
*[AS09500(BEF )04/95] *[AS09600(BEF )04/95]
*[AS09700(BEF )04/95]
CAUTION: The use of optical instruments with this product will increase eye hazard as the laser beam used in this compact disc player is harmful to the eyes. Do not attempt to disassemble the case. Refer servicing to qualified personnel only. Common Operating Conditions of Your CD Player
The following information is designed to help you recognize typical situations that could be mistakenly interpreted as mechanical malfunctions of the disc player. q A disc is already loaded. q The disc is inserted with the label surface
downward.
q The disc is dusty or defective. q The player’s internal temperature is above 140˚F (60˚C). Allow the player to cool off before operating.
q Different manufacturers of compact discs may
produce discs with different dimensions or tolerances, some of which may not be within industry standards or in accordance with the CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player.
161
File:ltasb.ex Update:Fri Jun 9 15:27:22 1995
*[AS09800(BEF )04/95]
*[AS09850(BEF )04/95] *[AS09900(BEF )04/95] *[AS10000(BEF )05/95]
*[AS10100(BEF )04/95] *[AS10200(BEF )04/95]
If play does not begin after the CD button is pushed: q The radio is not on. q The unit is in the stop mode. q Moisture may have condensed on the lenses within the unit. If this occurs, remove the CD magazine and wait approximately an hour until the moisture evaporates.
If the sound skips: q Badly scratched discs or extremely rough
roads will cause the sound to skip. Skipping will not damage the disc player or scratch the discs.
162
f
