Download PDF Manual

107
108
109
110
111
112
113
114
115
116
210
211
212
301
302
303


Fuse Amp


Passenger Compartment Fuse


Rating 20A* 10A* 15A* 10A*



10A* 10A* 10A*



30A** 30A** 30A**


— — —


20A** 30A** 30A** 30A**



30A** 30A** 30A** 20A** 30A**



1⁄2 ISO relay



Full ISO relay Full ISO relay



Panel Description


Fuel pump Instrument cluster Delayed accessory Fog lamps Not used Ignition switch RUN/START feed Left-hand low beam headlamp Right-hand low beam headlamp Not used Trailer tow EBC BSM (Door locks) Ignition switch Not used Not used Not used Trailer tow battery charge Upfitter #1
Upfitter #2
Ignition switch Not used Power seat (Driver) Starter Power seat (Passenger) Upfitter control Ignition switch Not used Back-up lamps Not used Trailer tow battery charge Powertrain Control Module (PCM) Not used


210


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Fuse/Relay Location


304
305
306
307
601


Roadside Emergencies


Passenger Compartment Fuse


Panel Description


Not used Upfitter control


Full ISO relay Full ISO relay Delayed accessory Full ISO relay


Fuse Amp


Rating



30A circuit


breaker


Starter Delayed accessory, Power windows, Moonroof Not used


602


— * Mini fuse ** Cartridge fuse


Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.


Always disconnect the battery before servicing high current fuses.


To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or


refilling fluid reservoirs.


If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.


211


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


The high-current fuses and relays are coded as follows.


Fuse/Relay Location


10


11


212


Fuse Amp


Power Distribution Box


Rating 30A* 40A* 30A*



50A*



30A*



20A** 10A**


10A**


Description


Wipers Blower Electronic Shift on the Fly (ESOF) Not used Injector Driver Module (IDM) (Diesel engine only) Not used Horizontal Fuel Conditioner Module (HFCM) (Diesel engine only) Shunt Trailer tow turn signals Powertrain Control Module (PCM) keep alive power, Canister vent solenoid (gasoline engine only) Anti-lock Brake System (ABS)


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Fuse Amp


Power Distribution Box


Description


Rating 2A** 15A**






10A**


15A**


10A** 10A**


60A*** 60A***


Brake pressure switch Daytime Running Lamps (DRL) Not used IDM logic (Diesel engine only) Not used A/C clutch IDM relay (Diesel engine only) Not used Trailer tow back-up lamps Not used ABS (Coils) ABS (Pump) Trailer tow right turn signal/stop lamp Trailer tow left turn signal/stop lamp A/C clutch Not used DRL #1
1⁄2 ISO relay 1⁄2 ISO relay DRL #2
Full ISO relay DRL #3
Full ISO relay HFCM Blower Full ISO relay High-current IDM (Diesel engine only)


1⁄2 ISO relay


1⁄2 ISO relay


1⁄2 ISO relay



Fuse/Relay Location


12
13
14
15
16
17
18
19
20
21
22
23
201


202


203
204
205
206
301
302
303
304


* Cartridge Fuse ** Mini Fuses *** Maxi fuse


relay


213


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Relays


An auxiliary relay box is located in the left-hand front side of the engine compartment. This box contains relays for the Electronic Shift On the Fly (ESOF) system. Please see your authorized dealer for troubleshooting or service of these relays.


CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. The use of tire sealants may damage your tires.


Dissimilar spare tire/wheel information


Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.


If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.


214


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


tire


load rating listed on the Safety Compliance Label


A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h)Load the vehicle beyond maximum vehicle • Use snow chains on the end of the vehicle with the dissimilar spare • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability It is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessary, do not operate above speeds of 10 mph (16 km/h) or for distances above 50
miles (80 km). 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare


tire/wheel


215


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.


Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113 km/h). It is intended for temporary use only. This means if you need to use it, you should replace it as soon as possible. Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools, refer to the following table for their locations:


Tool


Spare tire (pick-up trucks only) Jack


Under the vehicle, just forward of the rear bumper


Location


Regular cab, Super Cab without rear bench seat and Crew Cab: Fastened to floor pan behind rearmost seat on passenger side SuperCab with rear bench seat: Under rear bench on passenger side


216


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Tool


Jack handle and lug wrench


Key, spare tire lock


Location


Regular cab: Fastened to floor behind front seat Super Cab: Fastened to floor under rear seat Crew Cab: Fastened to floor behind rear seat In the glove box


Removing the spare tire (with spare tire carrier only) 1. The following tools are required to remove the spare tire: • one handle extension and one typical extension. To assemble, align button with hole and slide parts together. To disconnect, depress button and pull apart.


• one wheel nut wrench. Slide over


square end of jack handle.


• Vehicles equipped with dual rear wheels, insert the lug wrench extension into the lug wrench to reach the lug nuts.


2. Attach the spare tire lock key (A) to the jack handle (B).


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


217


Roadside Emergencies


3. Fully insert the jack handle through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. Some resistance will be felt when turning the jack handle assembly. 4. Turn the handle counterclockwise and lower the spare tire until you can slide the tire rearward and the cable is slack. 5. Remove the retainer through the center of the wheel.


Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake. • Automatic transmission: Place gearshift lever in P (Park). • Manual transmission: Place • Electronic Shift-On-the-Fly


gearshift lever in R (Reverse).


(ESOF) 4WD: Place transfer case in any position. • Manual shift transfer case 4WD: Place transfer case in 2H, 4H or 4L.


To help prevent the vehicle from moving when you


change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.


2. Turn engine off and block the diagonally opposite wheel (block not provided).


218


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


3. Remove the jack, jack handle, lug wrench and spare tire from the stowage locations. 4. Use the tip of the lug wrench to remove any wheel trim. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.


When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the


jack, even if the transmission is in P (Park) (automatic transmission) or R (Reverse) (manual transmission). To prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and the diagonally opposite wheel is blocked.


If the vehicle slips off the jack, you or someone else could be seriously injured.


The following steps apply to F–250/F–350 Single Rear Wheel (SRW) vehicles only (unless otherwise noted): 6. Insert the hooked end of the jack handle into the jack and use the handle to slide the jack under the vehicle. 7. Position the jack according to the following guides: • Front (4x2)


219


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies • Front driver side (4x4) Note: Make sure the jack fits onto the flat area on the outboard side of the differential.


• Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle.


• Rear (including F-350 Dual Rear


wheel [DRW] vehicles)


220


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Never use the front or rear differential as a jacking point.


To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.


8. Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 9. Remove the lug nuts with the lug wrench. 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front wheels and single rear wheel vehicles. If replacing an inboard rear tire on dual rear wheel vehicles, the valve stem must be facing outward. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 11. Lower the wheel by turning the jack handle counterclockwise. Go to step 19. The following steps apply to F–350 DRW and F–450/F–550
vehicles only: 12. Slide the notched end of the jack handle over the release valve and use the handle to slide the jack under the vehicle. Make sure the valve is closed by turning it clockwise.


221


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


13. Position the jack according to the following guides: • Front (4x2): F–350 DRW Note: Place jack directly under I-beam pin as shown in the illustration.


• Front driver side (4x4): F–350


DRW


Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing.


• Front passenger side (4x4): F-350


DRW


Note: View shown from the rear of the vehicle to clearly identify the jack point. Note: Place the jack directly under axle and inboard of the radius arm so that the jack clears the radius arm.


222


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


• Front: F–450/F–550


Roadside Emergencies


• Rear: F-450/F-550


14. Insert the jack handle into the pump linkage. 15. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’s rated capacity. 16. Remove the lug nuts with the lug wrench. 17. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 18. Lower the wheel by slowly turning the release valve counterclockwise. Opening the release valve slowly will provide a more controlled rate of descent.


223


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


The following steps apply to all vehicles: 19. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 8–lug nut torque sequence


10–lug nut torque sequence


20. Stow the flat tire. Refer to Stowing the spare tire if the vehicle is equipped with a spare tire carrier. Note: If your vehicle is equipped with 20” tires, do not stow the flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 21. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not rattle when driving. 22. Unblock the wheels.


224


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the direction specified on the Tire Changing Instructions located with the jack hardware. 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center. Pull on the cable to align the components at the end of the cable. 3. Turn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness. Tighten to the best of your ability, to the point where the ratchet/slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, take the vehicle to your authorized dealer for assistance at your earliest convenience. 4. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary. Failure to properly stow the spare tire may result in failure of the winch cable and loss of the tire. 5. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, per scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. 6. If removed, install the spare tire lock (if equipped) into the bumper drive tube with the spare tire lock key (if equipped) and jack handle.


WHEEL LUG NUT TORQUE SPECIFICATIONS On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles (160 km), and again at 500 miles (800 km) of new vehicle operation and after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).


225


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Bolt size


Wheel lug nut torque*


N•m 200


lb.ft. 150


M14 x 1.5
* Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel stud threads.


When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control.


JUMP STARTING YOUR VEHICLE


The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or


vehicle damage.


Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.


Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter.


226


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off.


Connecting the jumper cables


+–


+–


1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.


227


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


+–


+–


2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.


+–


+–


3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.


228


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


+–


+–


4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.


Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an


explosion of the gases that surround the battery.


5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.


Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.


229


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Removing the jumper cables


+–


+–


Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.


+–


+–


2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.


230


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


+–


+–


3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.


+–


+–


4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.


231


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


WRECKER TOWING


If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift On 4x4 vehicles, it is recommended that your vehicle be towed using flatbed equipment with all the wheels off the ground. However, a wheel lift may be used to lift the rear of the vehicle so long as, depending on vehicle configurations, the following preparations are met: • On Electronic Shift-On-the-Fly (ESOF) vehicles, the 4WD control is • On manual-shift transfer case vehicles, the front wheel hub locks are


turned to the 2WD position prior to towing.


in the UNLOCKED position prior to towing.


Note: Towing an ESOF 4WD vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatic transmission.


232


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Roadside Emergencies


Note: Towing an a 4x2 or an ESOF 4WD vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph (56 km/h) may cause damage to the automatic transmission. Note: On Dual Rear Wheel (DRW) vehicles, an outer rear wheel must be removed prior to using a wheel lift wrecker. If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.


233


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


GETTING THE SERVICES YOU NEED


At home You must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford. If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. 2. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. 3. If you require assistance or clarification on Ford Motor Company policies or procedures, please contact the Ford Customer Relationship Center at 1-800-392-3673 (FORD).


Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you. In the United States: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) www.customersaskford.com


234


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you. In the United States: Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
1-800-521-4140
(TDD for the hearing impaired: 1-800-232-5952) www.customersaskford.com In Canada: Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-387-9333
www.lincolncanada.com In order to help you service your Lincoln vehicle, please have the following information available when contacting the Lincoln Centre: • Your telephone number (home and business) • The name of the authorized dealer and the city where the authorized • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) Additional Assistance If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.).


dealer is located


235


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.


IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126


236


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. Initially, the BBB will try to resolve your question or concern through mediation. Mediation is a process through which a representative of the BBB will contact the parties and explore options for settlement of your claim. If mediation is not successful, customers with eligible claims may participate in the BBB AUTO LINE arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. You are not bound by the decision but may choose to accept it. If you choose to accept the BBB AUTO LINE decision then Ford must abide by the accepted decision as well. If the arbitrator has decided in your favor and you accept the decision, the BBB AUTO LINE program will contact you to ensure that Ford has complied with the decision in a timely manner. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. To file a claim with the BBB AUTO LINE, you will be asked for your name and address, information about your vehicle, information about your concerns and any steps you have already taken to try to resolve them. You can get more information by calling BBB AUTO LINE at 1–800–428–3718, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800
Arlington, Virginia 22203–1833
Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.


237


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all Canadian territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.


FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. It provides the following: • Benefits during the warranty period depending on the plan you


purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).


• Protection against covered repair costs after your Bumper-to-Bumper


Warranty expires.


You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada authorized dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 4,600 participating Ford or Lincoln Mercury and Ford of Canada authorized dealers.


238


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.


GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
If you are in another foreign country, contact the nearest authorized dealer. If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Worldwide Direct Market Operations.


239


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Customer Assistance


ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207
Or call: For a free publication catalog, order toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.)


Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.


REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C. area) or write to: NHTSA 400 Seventh Street U.S. Department of Transportation Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from the Hotline.


240


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing


or laundry liquid. These products can discolor and spot painted surfaces.


strong, direct sunlight.


• Never wash a vehicle that is “hot to the touch” or during exposure to • Always use a clean sponge or car wash mitt with plenty of water for • Dry the vehicle with a chamois or soft terry cloth towel in order to • It is especially important to wash the vehicle regularly during the


eliminate water spotting.


best results.


winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppings


car wash.


and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. • Remove any exterior accessories, such as antennas, before entering a • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.


• If your vehicle is equipped with running boards, do not use rubber, plastic and vinyl protectant products on the running board surface, as the area may become slippery.


WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives. Use Motorcraft Premium


Liquid Wax, ZC-53-A, which is available from your authorized dealer, or an equivalent quality product.


241


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.


PAINT CHIPS Your authorized dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft Wheel and Tire Cleaner (ZC-37–A),


which is available from your authorized dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water.


• Never apply any cleaning chemical to hot or warm wheel rims or covers. • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.


• Do not use hydrofluoric acid-based or high caustic-based wheel • To remove tar and grease, use Motorcraft Bug and Tar Remover


cleaners, steel wool, fuels or strong household detergent.


(ZC-42), available from your authorized dealer.


ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the


engine block or other engine components.


242


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts • Never wash or rinse the engine while it is running; water in the • Cover the highlighted areas to prevent water damage when cleaning


that require cleaning and pressure rinse clean.


running engine may cause internal damage.


the engine.


• 5.4L V8 gasoline engine


• 6.8L V10 gasoline engine


243


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass


Remover (ZC-42).


Cleaner (ZC-23).


WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellant coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with


a non-abrasive cleaner such as Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23), available from your authorized dealer.


• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or


Motorcraft Premium Windshield Washer Concentrate (ZC-32–A), available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly.


• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a clean, dry cloth. • Avoid cleaners or polish that increase the gloss of the upper portion of


the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.


244


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of


the airbag system. • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces.


INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then dry by wiping • Do not use household or glass cleaners as these may damage the


with a dry, soft, clean cloth.


finish.


Carpet & Upholstery Cleaner (ZC-54).


INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional Strength • If grease or tar is present on the material, spot-clean the area first • If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.


immediately (but do not oversaturate) or the ring will set.


with Motorcraft Spot and Stain Remover (ZC-14).


Do not use cleaning solvents, bleach or dye on the vehicle’s seatbelts, as these actions may weaken the belt webbing.


LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCH F–250 AND F–350 CREWCAB) Your leather seating surfaces have a clear, protective coating over the leather. For King Ranch F-250 and F-350 CrewCab leather seats, refer to separate section in this chapter. • To clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl


Cleaner (ZC-11–A). Dry the area with a soft cloth.


245


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning • To help maintain its resiliency and color, use the Motorcraft Deluxe Leather Care Kit (ZC-11–D), available from your authorized dealer. • Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear, protective coating on the seat.


Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining.


LEATHER SEATS FOR THE KING RANCH F-250 AND F-350
CREWCAB ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grain leather which is extremely durable, but still requires special care and maintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintain the appearance of the leather. Failure to care for the leather can result in drying out and fading of the material. Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining. Cleaning For dirt, use a vacuum cleaner then use a clean, damp cloth or soft brush. For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap. If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product “Tanners Preserve Leather Cleaner” and a 3M “Type T” scrubbing pad. • Clean spills as quickly as possible. • Test any cleaner or stain remover on an inconspicuous part of the


leather as cleaners may darken the leather. For more specific cleaning information, contact the King Ranch Saddle Shop at 1–800–282–KING (5464).


• Do not spill coffee, ketchup, mustard, orange juice or oil-based • Do not use household cleaning products, alcohol solutions, solvents or


products on the leather as they may permanently stain the leather.


cleaners intended for rubber, vinyl or plastics.


246


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars. These markings give character to the seating covers and should be considered as proof of a genuine leather product. In order to lessen the appearance of certain scratches and other wear marks, apply conditioner on the affected area following the same instructions as in the Conditioning section. Conditioning Bottles of King Ranch Leather Conditioner are available at the King Ranch Saddle Shop. Visit the Web site at www.krsaddleshop.com, or telephone (in the United States) 1–800–282–KING (5464). If you are unable to obtain King Ranch Leather Conditioner, use another premium leather conditioner. • Apply your first conditioning treatment within six months of taking delivery of your vehicle. Condition twice yearly in order to replenish lost oils and revitalize the aroma, suppleness and resilience of the leather.


• Clean the surfaces using the steps outlined in the Cleaning section. • Ensure the leather is dry then apply a nickel-sized amount of • Rub the conditioner into leather until it disappears. Allow the


conditioner to a clean, dry cloth


conditioner to dry and repeat the process for the entire interior. If a film appears, wipe off film with a dry, clean cloth.


UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. Note: Use care when using a power washer to clean the driveline, especially the driveshaft and interfacing components. The high-pressure fluid could penetrate the sealed parts and cause damage.


247


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Cleaning


FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Car Care Kit (ZC-26) Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail Wash (ZC-3–A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.S only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft One Step Wash and Wax Concentrate (ZC-6-A) Motorcraft Paint Sealant (ZC-45) Motorcraft Premium Car Wash Concentrate (U.S. only) (ZC-17-B) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Liquid Wax (ZC-53–A) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft Tire Clean and Shine (ZC-28) Motorcraft Triple Clean (U.S. only) (ZC-13) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Vinyl Cleaner (Canada only) (CXC-93) Motorcraft Vinyl Conditioner (Canada only) (CXC-94) Motorcraft Wheel and Tire Cleaner (ZC-37–A)


248


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy • We provide a scheduled maintenance guide which makes tracking


location.


routine service easy.


If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft parts are designed and built to provide the best performance in your vehicle.


PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed • Keep all open flames and other burning (cigarettes) material away


space, unless you are sure you have enough ventilation.


from the battery and all fuel related parts.


Working with the engine off • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in 1
(First). 2. Turn off the engine and remove the key. 3. Block the wheels.


249


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.


OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.


2. Go to the front of the vehicle and release the auxiliary latch located under the right center of the hood. Slide the handle to release the auxiliary latch. 3. Lift the hood until the lift cylinders hold it open.


250


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT


5.4L V8 gasoline engines Refer to the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations.


1. Transmission fluid dipstick (automatic transmission) 2. Air filter assembly 3. Engine coolant reservoir 4. Brake fluid reservoir 5. Clutch fluid reservoir (manual transmission) 6. Power distribution box 7. Power steering fluid reservoir 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoir 11. Battery


251


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


6.8L V10 gasoline engine Refer to the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations.


11


10


1. Transmission fluid dipstick (automatic transmission) 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Clutch fluid reservoir (manual transmission) 5. Power distribution box 6. Power steering fluid reservoir 7. Air filter assembly 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoir 11. Battery


252


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellant-type fluid or bug wash as this may cause a squeaking/chattering noise, streaking or smearing. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.


If you operate your vehicle in temperatures below 40°F (4.5°C), use washer fluid with antifreeze protection. Failure to use


washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.


Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components.


253


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. 3. Replace wiper blades at least once per year for optimum performance. 4. Poor wiper quality can be improved by cleaning the wiper blades and the windshield; refer to Windows and wiper blades in the Cleaning chapter. 5. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.


ENGINE OIL


Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat.


254


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


5. Locate and carefully remove the engine oil level indicator (dipstick). • 5.4L V8 engine


• 6.8L V10 engine


255


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range.


• Oil levels above the MAX mark may cause engine damage. Some oil


must be removed from the engine by a service technician.


7. Put the indicator back in and ensure it is fully seated.


Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn or until the cap is fully seated. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.


256


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Engine oil and filter recommendations Look for this certification trademark.


Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine. Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.


257


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.


However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance information for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells. If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. When the battery is disconnected or a new battery installed, the transmission must learn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will fully update transmission operation to its optimum shift feel. Note: Electrical or electronic accessories or components added to the vehicle by the authorized dealer or the owner may adversely affect battery performance and durability.


258


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted


substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.


When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps,


resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.


Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.


Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.


For information on transmission operation after the battery has been disconnected, refer to Shift strategy in the Driving chapter. Because your vehicle’s engine is also electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute.


259


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


relearn the idle and fuel trim strategy.


6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.


If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.


RECYCLE


ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage (kilometer) intervals listed in the scheduled maintenance information. The coolant concentration should be maintained at 50/50
coolant and distilled water, which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060). The level of coolant should be maintained at the “FULL COLD” level or within the “COLD FILL RANGE” in the coolant reservoir. If the level falls below, add coolant per the instructions in the Adding engine coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50/50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265°F (129°C). • Protection against rust and other forms of corrosion.


260


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


• Enables calibrated gauges to work properly. • All engines


MAX M I N


When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the


“COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).


• Refer to the scheduled maintenance information for service interval • Be sure to read and understand Precautions when servicing your


schedules.


vehicle in this chapter.


If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.


261


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained.


Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.


Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could


make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant


(yellow-colored), VC-7–A (U.S., except CA, OR and NM), VC-7–B (CA, OR and NM), meeting Ford Specification WSS-M97B51–A1.


Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, VC-2 (US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection. • A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing. • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.


• Do not add extra inhibitors or additives to the coolant. These


can be harmful and compromise the corrosion protection of the engine coolant.


262


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “FULL COLD” level. For all other vehicles which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.


To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The


cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.


1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (a translucent plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” or the “FULL COLD” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. Turn until tightly installed. (Cap must be tightly installed to prevent coolant loss.) After any coolant has been added, check the coolant concentration (refer to Checking engine coolant). If the concentration is not 50/50
(protection to –34°F/–36°C), drain some coolant and adjust the concentration. It may take several drains and additions to obtain a 50/50
coolant concentration. Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quart (1.0 liter) of engine coolant per month, have your authorized dealer check the engine cooling system. Your cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage.


263


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.


Used engine coolant should be disposed of in an appropriate


manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.


Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this section. If your vehicle is equipped with a diesel engine, refer to the Refill capacities section of your 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section.


Severe climates If you drive in extremely cold climates (less than –34°F [–36°C ]): • It may be necessary to increase the coolant concentration • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will


above 50%.


decrease the overheat protection characteristics of the engine coolant and may cause engine damage.


• Refer to the chart on the coolant container to ensure the


coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.


above 40%.


If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will


decrease the corrosion protection characteristics of the engine coolant and may cause engine damage.


264


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


• Decreased engine coolant concentrations below 40% will


decrease the freeze protection characteristics of the engine coolant and may cause engine damage.


• Refer to the chart on the coolant container to ensure the


coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.


Vehicles driven year-round in non-extreme climates should use a 50/50
mixture of engine coolant and distilled water for optimum cooling system and engine protection.


What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The message center will indicate the engine is overheating. • The Service engine soon


indicator light will illuminate.


If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage.


265


2006 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)


Maintenance and Specifications


When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to a service facility. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low.


Never remove the coolant reservoir cap while the engine is running or hot.


5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible.


FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to the scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.


WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS


Important safety precautions


Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.

Loading...
x