Login- Download PDF Manual
-
4 - VACUUM MUST BE FELT AGAINST FINGER 5 - ENGINE VALVE COVER
(3) The paper should be drawn against the opening in the valve cover with noticeable force. This will be after allowing approximately one minute for crank- case pressure to reduce.
(4) Turn engine off and remove PCV valve from valve cover. The valve should rattle when shaken (Fig. 24).
DR PCV VALVE (Continued)
EVAPORATIVE EMISSIONS
25 - 21
any solid particles. Blow out the fitting with shop air. If necessary, use a smaller drill to avoid removing any metal from the fitting.
REMOVAL
3.7L V-6 / 4.7L V-8
The PCV valve is located on the oil filler tube (Fig. 25). Two locating tabs are located on the side of the valve (Fig. 25). These 2 tabs fit into a cam lock in the oil filler tube. An o-ring seals the valve to the filler tube.
Fig.23VACUUMCHECKATVALVECOVER
OPENING-5.9LV-8
1 - STIFF PAPER PLACED OVER RUBBER GROMMET 2 - RUBBER GROMMET 3 - VALVE COVER 4 - FITTING REMOVED FROM VALVE COVER 5 - AIR TUBE
Fig.24SHAKEPCV-5.9LV-8
1 - PCV VALVE GROMMET 2 - PCV VALVE 3 - PCV VALVE MUST RATTLE WHEN SHAKEN
(5) Replace the PCV valve and retest the system if it does not operate as described in the preceding tests. Do not attempt to clean the old PCV valve. (6) If the paper is not held against the opening in valve cover after new valve is installed, the PCV valve hose may be restricted and must be replaced. The passage in the intake manifold must also be checked and cleaned.
(7) To clean the intake manifold fitting, turn a 1/4
inch drill (by hand) through the fitting to dislodgeFig.25PCVVALVE/OILFILLERTUBELOCATION-
3.7LV-6/4.7LV-8
1 - O-RING 2 - LOCATING TABS 3 - CAM LOCK 4 - OIL FILLER TUBE 5 - PCV LINE/HOSE 6 - PCV VALVE
(1) Disconnect PCV line/hose (Fig. 25) by discon-
necting rubber hose at PCV valve fitting.
(2) Remove PCV valve at oil filler tube by rotating PCV valve downward (counter-clockwise) until locat- ing tabs have been freed at cam lock (Fig. 25). After tabs have cleared, pull valve straight out from filler tube. To prevent damage to PCV valve locating
EVAPORATIVE EMISSIONS
25 - 22
PCV VALVE (Continued)tabs, valve must be pointed downward for removal. Do not force valve from oil filler tube. (3) After valve is removed, check condition of valve
o-ring (Fig. 25).
5.7L V-8
DR
The PCV valve is mounted into the top of the intake manifold, located to the right / rear of the throttle body (Fig. 12). The PCV valve is sealed to the intake manifold with 2 o-rings (Fig. 13).
(1) Remove PCV valve by rotating counter-clock- wise 90 degrees until locating tabs have been freed. After tabs have cleared, pull valve straight up from intake manifold.
(2) After valve is removed, check condition of 2
valve o-rings.
INSTALLATION
3.7L V6 / 4.7L V-8
The PCV valve is located on the oil filler tube. Two locating tabs are located on the side of the valve. These 2 tabs fit into a cam lock in the oil filler tube. An o-ring seals the valve to the filler tube.
(1) Return PCV valve back to oil filler tube by placing valve locating tabs into cam lock. Press PCV valve in and rotate valve upward. A slight click will be felt when tabs have engaged cam lock. Valve should be pointed towards rear of vehicle.
(2) Connect PCV line/hose and rubber hose to PCV
valve.
5.7L V-8
(1) Clean out intake manifold opening. (2) Check condition of 2 o-rings on PCV valve. (3) Apply engine oil to 2 o-rings. (4) Place PCV valve into intake manifold and
rotate 90 degrees clockwise for installation.
VACUUM LINES DESCRIPTION
A vacuum schematic for emission related items can be found on the vehicles VECI label. Refer to Vehicle Emission Control Information (VECI) Label for label location.
VAPOR CANISTER DESCRIPTION
Two, maintenance free, EVAP canisters are used. Both canisters are mounted into a two-piece support bracket located near the front of the fuel tank (Fig. 26).
Fig.26LOCATION,EVAPCANISTERS
1 - LDP 2 - LDP MOUNTING BOLT 3 - ELEC. CONNEC. 4 - FILTER MOUNTING BOLT 5 - LDP FILTER 6 - CONNECTING HOSE 7 - EVAP CANISTER MOUNTING BRACKET 8 - EVAP CANISTERS (2)
OPERATION
Two, maintenance
free, EVAP canisters
are used.The EVAP canisters are filled with granules of an activated carbon mixture. Fuel vapors entering the EVAP canisters are absorbed by the charcoal granules.
Fuel tank pressure vents into the EVAP canisters. Fuel vapors are temporarily held in the canisters until they can be drawn into the intake manifold. The duty cycle EVAP canister purge solenoid allows the EVAP canisters to be purged at predetermined times and at certain engine operating conditions.
REMOVAL
Two, maintenance free, EVAP canisters are used. Both canisters are mounted into a two-piece support bracket located near the front of the fuel tank (Fig. 26).
(1) Raise and support vehicle. (2) Remove fuel tubes/lines at each EVAP canister. Note location of tubes/lines before removal for easier installation.
(3) Remove lower support bracket (Fig. 27). (4) Remove mounting nuts at top of each canister
(Fig. 27).
DR VAPOR CANISTER (Continued)
EVAPORATIVE EMISSIONS
25 - 23
(5) Remove each canister
bracket.
from upper support
The NVLD pump is located in the same area as the
leak detection pump. Refer to NVLD Removal
1 - CANISTER MOUNTING NUTS 2 - CONNECTING HOSE 3 - UPPER SUPPORT BRACKET
Fig.27EVAPCANISTERS-REMOVAL/INSTALLATION 4 - LOWER SUPPORT BRACKET 5 - OUTER CANISTER 6 - INNER CANISTER
INSTALLATION
(1) Place each canister into upper support bracket
and install nuts. Refer to Torque Specifications.
(2) Install lower support bracket. Refer to Torque
Specifications.
(3) Carefully install vapor/vacuum lines. The vapor/vacuum lines and hoses must be firmly connected. Also check the vapor/vacuum lines at the LDP, LDP filter and EVAP canister purge solenoid for damage or leaks. If a leak is present, a Diagnostic Trouble Code (DTC) may be set.
NATURAL VAC LEAK DETECTION ASSY DESCRIPTION
Vehicles equipped with NGC engine control mod- ules use an NVLD pump and system.Vehicles equipped with JTEC engine control modules use an LDP (leak detection pump). Refer to Leak Detection Pump (LDP) for additional information.
Installation for additional information.
OPERATION
Vehicles equipped with NGC engine control mod- ules use an NVLD pump and system.Vehicles equipped with JTEC engine control modules use a leak detection pump. Refer to Leak Detection Pump (LDP) for additional information.
The Natural Vacuum Leak Detection (NVLD) sys- tem is the next generation evaporative leak detection system that will first be used on vehicles equipped with the Next Generation Controller (NGC). This new system replaces the leak detection pump as the method of evaporative system leak detection. This is to detect a leak equivalent to a 0.0209 (0.5 mm) hole. This system has the capability to detect holes of this size very dependably.
The basic leak detection theory employed with NVLD is the 9Gas Law9. This is to say that the pres- sure in a sealed vessel will change if the temperature of the gas in the vessel changes. The vessel will only see this effect if it is indeed sealed. Even small leaks will allow the pressure in the vessel to come to equi- librium with the ambient pressure. In addition to the
EVAPORATIVE EMISSIONS
25 - 24
NATURAL VAC LEAK DETECTION ASSY (Continued)DR
detection of very small leaks, this system has the capability of detecting medium as well as large evap- orative system leaks.
A vent valve seals the canister vent during engine off conditions. If the vapor system has a leak of less than the failure threshold, the evaporative system will be pulled into a vacuum, either due to the cool down from operating temperature or diurnal ambient temperature cycling. The diurnal effect is considered one of the primary contributors to the leak determi- nation by this diagnostic. When the vacuum in the system exceeds about 19 H2O (0.25 KPA), a vacuum switch closes. The switch closure sends a signal to the NGC. The NGC, via appropriate logic strategies, utilizes the switch signal, or lack thereof, to make a determination of whether a leak is present.
The NVLD device is designed with a normally open vacuum switch, a normally closed solenoid, and a seal, which is actuated by both the solenoid and a diaphragm. The NVLD is located on the atmospheric vent side of the canister. The NVLD assembly may be mounted on top of the canister outlet, or in-line between the canister and atmospheric vent filter. The normally open vacuum switch will close with about 19
H2O (0.25 KPA) vacuum in the evaporative system. The diaphragm actuates the switch. This is above the opening point of the fuel inlet check valve in the fill tube so cap off leaks can be detected. Submerged fill systems must have recirculation lines that do not have the in-line normally closed check valve that pro- tects the system from failed nozzle liquid ingestion, in order to detect cap off conditions.The normally closed valve in the NVLD is intended to maintain the seal on the evaporative system dur- ing the engine off condition. If vacuum in the evapo- rative system exceeds 39 to 69 H2O (0.75 to 1.5 KPA), the valve will be pulled off the seat, opening the seal. This will protect the system from excessive vacuum as well as allowing sufficient purge flow in the event that the solenoid was to become inoperative.
The solenoid actuates the valve to unseal the can- ister vent while the engine is running. It also will be used to close the vent during the medium and large leak tests and during the purge flow check. This sole- noid requires initial 1.5 amps of current to pull the valve open but after 100 ms. will be duty cycled down to an average of about 150 mA for the remainder of the drive cycle.
Another feature in the device is a diaphragm that will open the seal in the NVLD with pressure in the evaporative system. The device will 9blow off9 at about 0.59 H2O (0.12 KPA) pressure to permit the venting of vapors during refueling. An added benefit to this is that it will also allow the tank to 9breathe9
during increasing temperatures, thus limiting the pressure in the tank to this low level. This is benefi-cial because the induced vacuum during a subse- quent declining temperature will achieve the switch closed (pass threshold) sooner than if the tank had to decay from a built up pressure.
The device itself has 3 wires: Switch sense, sole- noid driver and ground. It also includes a resistor to protect the switch from a short to battery or a short to ground. The NGC utilizes a high-side driver to energize and duty-cycle the solenoid.
REMOVAL
The NVLD pump and filter are attached to the front of the EVAP canister mounting bracket (Fig. 28). This is located near the front of the fuel tank. The pump and filter are replaced (serviced) as one unit.
(1) Raise and support vehicle. (2) Carefully remove pump hose clamp and hose at
(3) Carefully remove other vapor/vacuum hose at
filter.
pump.
(4) Disconnect 3–way electrical connector at pump. (5) The NVLD pump snaps onto the EVAP canister mounting bracket. Press on release tab (Fig. 29) while sliding pump from bracket.
Fig.28NVLDPUMPLOCATION
1 - EVAP CANISTER MOUNTING BRACKET 2 - NVLD PUMP 3 - FILTER
INSTALLATION
(1) Install NVLD pump to EVAP canister mount-
ing bracket (snaps on).
DR NATURAL VAC LEAK DETECTION ASSY (Continued)
EVAPORATIVE EMISSIONS
25 - 25
(3) Carefully install vapor/vacuum lines to NVLD pump, and install hose to filter. The vapor/vacuum lines and hoses must be firmly connected. Check the vapor/vacuum lines at the NVLD pump, filter and EVAP canister purge solenoid for damage or leaks. If a leak is present, a Diag- nostic Trouble Code (DTC) may be set.
(4) Connect 3–way electrical connector to pump.
Fig.29REMOVE/INSTALLNVLDPUMP
1 - NVLD PUMP 2 - RELEASE TAB
(2) Install NVLD filter and bolt to EVAP canister
mounting bracket. Refer to Torque Specifications.
DR
Description
Group-Page
Description
Group-Page
Description
INDEX
Group-Page
SPECIFICATIONS, STRUCTURAL . . . . . . . . 23-113
AIR HEATER RELAY - OPERATION,
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 24-9
DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-22
ABS - DESCRIPTION, BRAKES ABS - OPERATION, BRAKES ABS BRAKE BLEEDING - STANDARD
. . . . . . . . . . . 5-39
. . . . . . . . . . . . . 5-39PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
ABS INDICATOR - DESCRIPTION . . . . . . . . . 8J-17
ABS INDICATOR - OPERATION . . . . . . . . . . 8J-17
A/C APPLICATION TABLE,SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 24-7
A/C COMPRESSOR CLUTCH -
A/C COMPRESSOR CLUTCH -
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 24-12
A/C COMPRESSOR CLUTCH -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 24-12
A/C COMPRESSOR CLUTCH -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9
. . 24-10A/C COMPRESSOR CLUTCH - REMOVAL A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE . . . . . . . . . . . . . . . 24-10
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING . . . . . . . . . . . . . 24-10
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 24-13
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 24-14
A/C COMPRESSOR CLUTCH RELAY -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 24-13
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14
A/C COMPRESSOR NOISE - DIAGNOSIS
AND TESTING . . . . . . . . . . . . . . . . . . . . . . . 24-36
A/C CONDENSER - DESCRIPTION . . . . . . . . . 24-39
A/C CONDENSER - OPERATION . . . . . . . . . . 24-39
A/C EVAPORATOR - DESCRIPTION . . . . . . . 24-47
A/C EVAPORATOR - INSTALLATION . . . . . . 24-47
A/C EVAPORATOR - OPERATION . . . . . . . . . 24-47
A/C EVAPORATOR - REMOVAL . . . . . . . . . . 24-47
A/C HEATER CONTROL - DESCRIPTION . . . 24-14
A/C HEATER CONTROL - INSTALLATION . . . 24-15
A/C HEATER CONTROL - REMOVAL . . . . . . 24-14
A/C ORIFICE TUBE - DESCRIPTION . . . . . . . 24-48
A/C ORIFICE TUBE - INSTALLATION . . . . . . 24-49
A/C ORIFICE TUBE - OPERATION . . . . . . . . 24-48
A/C ORIFICE TUBE - REMOVAL . . . . . . . . . . 24-49
A/C PERFORMANCE - DIAGNOSIS ANDTESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
A/C PRESSURE TRANSDUCER -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 24-15
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING . . . . . . . . . . . . . 24-15
A/C PRESSURE TRANSDUCER -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 24-16
A/C PRESSURE TRANSDUCER -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 24-15
A/C PRESSURE TRANSDUCER -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 24-16
ACCELERATOR PEDAL - INSTALLATION . . . 14-24
ACCELERATOR PEDAL - REMOVAL . . . . . . . 14-24
ACCELERATOR PEDAL POSITIONSENSOR - DESCRIPTION . . . . . . . . . . . . . . . 14-25
ACCELERATOR PEDAL POSITION
SENSOR - INSTALLATION . . . . . . . . . . . . . . 14-25
ACCELERATOR PEDAL POSITION
SENSOR - OPERATION . . . . . . . . . . . . . . . . 14-25
ACCELERATOR PEDAL POSITION
SENSOR - REMOVAL . . . . . . . . . . . . . . . . . . 14-25
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING . . . . . . . . . . . . . . . . 7-25,7-28,7-31
ACCUMULATOR - DESCRIPTION . . . . . . . . . 24-49
ACCUMULATOR - DESCRIPTION . . 21-191,21-372
ACCUMULATOR - INSPECTION . . . 21-192,21-373
ACCUMULATOR - INSTALLATION . . . . . . . . 24-50
ACCUMULATOR - OPERATION . . . . . . . . . . 24-49
ACCUMULATOR - OPERATION . . . . 21-192,21-373
ACCUMULATOR - REMOVAL . . . . . . . . . . . . 24-49
ACM COVER - INSTALLATION . . . . . . . . . . . . 8O-9
ACM COVER - REMOVAL . . . . . . . . . . . . . . . 8O-9
ACTUATION TEST MODE - DESCRIPTION,CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-1
ACTUATOR - DESCRIPTION, BLEND
DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-16
ACTUATOR - DESCRIPTION, FUEL
ACTUATOR - INSTALLATION, BLEND
DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-17
ACTUATOR - INSTALLATION, FLOOR -
DEFROST DOOR . . . . . . . . . . . . . . . . . . . . . 24-20
ACTUATOR - INSTALLATION, FUEL
CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . 14-85
ACTUATOR - INSTALLATION, INSIDE
HANDLE . . . . . . . . . . . . . . . . . . . . . . . 23-22,23-32
ACTUATOR - INSTALLATION, MODE
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR . . . . . . . . . . . . . . . . 24-23
. . 24-16ACTUATOR - OPERATION, BLEND DOOR ACTUATOR - OPERATION, FUEL
CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . 14-85
ACTUATOR - OPERATION, MODE DOOR . . . 24-21
ACTUATOR - OPERATION,RECIRCULATION DOOR . . . . . . . . . . . . . . . . 24-22
ACTUATOR - REMOVAL, BLEND DOOR . . . . 24-17
ACTUATOR - REMOVAL, FLOOR -ACTUATOR - REMOVAL, FUEL CONTROL ACTUATOR - REMOVAL, INSIDE HANDLE
DEFROST DOOR . . . . . . . . . . . . . . . . . . . . . 24-19
. . 14-85
. 23-22, 23-31
. . . . 24-21ACTUATOR - REMOVAL, MODE DOOR ACTUATOR - REMOVAL, RECIRCULATION
DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-22
ADAPTER HOUSING SEAL -
ADAPTER HOUSING SEAL - REMOVAL
INSTALLATION . . . . . . . . . . . 21-127,21-539,21-83
. . 21-127, 21-539,21-83ADAPTER MOUNT - INSTALLATION, DISC
BRAKE CALIPER . . . . . . . . . . . . . . . . . . . . . . 5-17
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE . . . . . . . . . . . . . . . . 7-19
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING . . . . . . . . . . . . . . . . . . 7-19
ADHESIVE LOCATIONS -
ADJUSTABLE PEDAL MOTOR -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 5-24
ADJUSTABLE PEDAL MOTOR -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5-24
. . 5-24ADJUSTABLE PEDAL MOTOR - REMOVAL ADJUSTABLE PEDAL SWITCH -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
ADJUSTABLE PEDAL SWITCH -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
ADJUSTER - DIAGNOSIS AND TESTING,
HYDRAULIC LASH . . . . . . . . . . . . . . . . 9-124,9-31
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP . . . . . . . . . . . . . . . . . . . . . 8O-50
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP . . . . . . . . . . . . . . . . . . . . . 8O-50
ADJUSTER ASSEMBLY - DESCRIPTION,
ROCKER ARM . . . . . . . . . . . . . . . . . . . . . . . 9-124
ADJUSTER ASSEMBLY - INSTALLATION,
ROCKER ARM . . . . . . . . . . . . . . . . . . 9-124,9-249
ADJUSTER ASSEMBLY - REMOVAL,
ROCKER ARM . . . . . . . . . . . . . . . . . . 9-124,9-249
ADJUSTER ASSY - CLEANING, ROCKER
ARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-310
ADJUSTER ASSY - DESCRIPTION,
ROCKER ARM . . . . . . . . . . . . . . . . . . . . . . . 9-310
ADJUSTER ASSY - INSPECTION,
ROCKER ARM . . . . . . . . . . . . . . . . . . . . . . . 9-311
ADJUSTER ASSY - INSTALLATION,
ROCKER ARM . . . . . . . . . . . . . 9-198,9-312,9-379
ADJUSTER ASSY - REMOVAL, ROCKER
ARM . . . . . . . . . . . . . . . . . . . . 9-198,9-310,9-379
ADJUSTING TOOL - ADJUSTMENT, WITH . . . 5-36
AFTER A SUPPLEMENTAL RESTRAINTDEPLOYMENT - STANDARD PROCEDURE, SERVICE . . . . . . . . . . . . . . . . . 8O-7
AIR CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . 21-494
AIR CLEANER ELEMENT - INSTALLATION . 9-105, 9-20,9-242,9-298,9-370
AIR CLEANER ELEMENT - REMOVAL . 9-105,9-20, 9-242,9-297,9-370AIR CONDITIONER - DESCRIPTION,
CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . 14-85
HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-1
ACTUATOR - DESCRIPTION, MODE
DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-20
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR . . . . . . . . . . . . . . . . 24-22
AIR CONDITIONER - OPERATION,
HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-1
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITH . . . . . . . 7-70
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITHOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-70
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITH . . . . . . . . . . . . . 7-68
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITHOUT . . . . . . . . . . 7-69
AIR CONTROL MOTOR - DESCRIPTION,
IDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-33
AIR CONTROL MOTOR - INSTALLATION,
IDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-35
AIR CONTROL MOTOR - OPERATION,
IDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-33
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-34
AIR COOLER AND PLUMBING -CLEANING, CHARGE . . . . . . . . . . . . . . . . . . 11-16
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE . . . . . . . . . . . . . . . 11-15
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE . . . . . . . . . . . . . . . . . 11-16
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE . . . . . . . . . . . . . . . 11-16
AIR COOLER AND PLUMBING -
OPERATION, CHARGE . . . . . . . . . . . . . . . . . 11-15
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE . . . . . . . . . . . . . . . . . . 11-15
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE . . . . . . 11-15
. . . . . . . . 13-2
AIR DAM - INSTALLATION, FRONT AIR DAM - REMOVAL, FRONT . . . . . . . . . . . 13-2
AIR HEATER - DESCRIPTION, INTAKE . . . . . 14-91
. . . . 14-91
AIR HEATER - INSTALLATION, INTAKE AIR HEATER - OPERATION, INTAKE . . . . . . 14-91
AIR HEATER - REMOVAL, INTAKE . . . . . . . . 14-91
AIR HEATER RELAY - DESCRIPTION,INTAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-92
AIR HEATER RELAY - INSTALLATION,
INTAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-93
INTAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-92
AIR HEATER RELAY - REMOVAL, INTAKE . . 14-93
AIR INTAKE SYSTEM - INSTALLATION . . . . 9-194
AIR INTAKE SYSTEM - REMOVAL . . . . . . . . 9-194
AIR TEMPERATURE SENSOR -DESCRIPTION, INTAKE . . . . . . . . . . . . . . . . 14-36
AIR TEMPERATURE SENSOR -
INSTALLATION, INTAKE . . . . . . . . . . . . . . . . 14-38
AIR TEMPERATURE SENSOR -
OPERATION, INTAKE . . . . . . . . . . . . . . . . . . 14-36
AIR TEMPERATURE SENSOR -
REMOVAL, INTAKE . . . . . . . . . . . . . . . . . . . 14-36
AIR TEMPERATURE SENSOR/MAP
SENSOR - DESCRIPTION, INTAKE . . . . . . . . 14-93
AIR TEMPERATURE SENSOR/MAP
SENSOR - INSTALLATION, INTAKE . . . . . . . 14-94
AIR TEMPERATURE SENSOR/MAP
SENSOR - OPERATION, INTAKE . . . . . . . . . 14-93
AIR TEMPERATURE SENSOR/MAP
SENSOR - REMOVAL, INTAKE . . . . . . . . . . . 14-93
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - DESCRIPTION, INLET . . . . . . . . . 14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - INSTALLATION, INLET . . . . . . . . 14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - OPERATION, INLET . . . . . . . . . . 14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - REMOVAL, INLET . . . . . . . . . . . . 14-90
AIR TESTING TRANSMISSION CLUTCH AND BAND OPERATION - DIAGNOSIS AND TESTING . . . . . . . . . . . . . . . . 21-143,21-324
. . . . . 7-75
AIR TO OIL COOLER - INSTALLATION AIR TO OIL COOLER - REMOVAL . . . . . . . . . 7-74
AIRBAG - DESCRIPTION, DRIVER . . . . . . . . 8O-22
AIRBAG - DESCRIPTION, PASSENGER . . . . 8O-34
AIRBAG - DESCRIPTION, SIDE CURTAIN . . 8O-51
AIRBAG - INSTALLATION, DRIVER . . . . . . . 8O-24
AIRBAG - INSTALLATION, PASSENGER . . . 8O-37
AIRBAG - INSTALLATION, SIDE CURTAIN . . 8O-53
AIRBAG - OPERATION, DRIVER . . . . . . . . . 8O-23
AIRBAG - OPERATION, PASSENGER . . . . . . 8O-35
AIRBAG - OPERATION, SIDE CURTAIN . . . . 8O-51
AIRBAG - REMOVAL, DRIVER . . . . . . . . . . . 8O-23
AIRBAG - REMOVAL, PASSENGER . . . . . . . 8O-35
AIRBAG - REMOVAL, SIDE CURTAIN . . . . . 8O-52
AIRBAG CONTROL MODULE -DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 8O-10
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT . . . . . . . . . . . 8O-53
2
INDEX
Description
Group-Page
Description
Group-Page
Description
Group-Page
DR
AIRBAG CONTROL MODULE -
ARM / ADJUSTER ASSEMBLY -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 8O-12
INSTALLATION, ROCKER . . . . . . . . . . 9-124,9-249
AIRBAG CONTROL MODULE -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8O-10
AIRBAG CONTROL MODULE -
OPERATION, SIDE IMPACT . . . . . . . . . . . . . 8O-54
AIRBAG CONTROL MODULE - REMOVAL . . 8O-11
AIRBAG INDICATOR - DESCRIPTION . . . . . . 8J-18
AIRBAG INDICATOR - OPERATION . . . . . . . 8J-18
AIRBAG ON/OFF SWITCH -DESCRIPTION, PASSENGER . . . . . . . . . . . . 8O-38
AIRBAG ON/OFF SWITCH -
INSTALLATION, PASSENGER . . . . . . . . . . . 8O-39
AIRBAG ON/OFF SWITCH - OPERATION,
PASSENGER . . . . . . . . . . . . . . . . . . . . . . . . 8O-38
AIRBAG ON/OFF SWITCH - REMOVAL,
PASSENGER . . . . . . . . . . . . . . . . . . . . . . . . 8O-39
AJAR INDICATOR - DESCRIPTION, DOOR . . 8J-23
AJAR INDICATOR - OPERATION, DOOR . . . 8J-23
AJAR SWITCH - DESCRIPTION, DOOR . . . . 8L-25
AJAR SWITCH - OPERATION, DOOR . . . . . . 8L-25
ALIGNMENT - DESCRIPTION, WHEEL . . . . . . . 2-1
ALIGNMENT - OPERATION, WHEEL . . . . . . . . 2-2
ALIGNMENT - SPECIAL TOOLS,HEADLAMP . . . . . . . . . . . . . . . . . . . . . . . . . . 8L-7
ALIGNMENT LINK/COIL SUSPENSION -
STANDARD PROCEDURE . . . . . . . . . . . . . . . . . 2-5
. . . . . 2-7
. . . . . . . . . . . . 2-6ALIGNMENT, SPECIAL TOOLS - WHEEL ALIGNMENT, SPECIFICATIONS ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE . . 21-156,21-337,21-495
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-10
AMBIENT TEMP SENSOR - OPERATION . . 8M-10
AMBIENT TEMPERATURE SENSOR -DIAGNOSIS AND TESTING . . . . . . . . . . . . . 8M-11
AMBIENT TEMPERATURE SENSOR
CIRCUIT - DIAGNOSIS AND TESTING . . . . 8M-11
AMPLIFIER - DESCRIPTION . . . . . . . . . . . . . 8A-3
AMPLIFIER - INSTALLATION . . . . . . . . . . . . . 8A-4
AMPLIFIER - OPERATION . . . . . . . . . . . . . . . 8A-3
AMPLIFIER - REMOVAL . . . . . . . . . . . . . . . . 8A-3
ANCHOR - DESCRIPTION, CHILDRESTRAINT . . . . . . . . . . . . . . . . . . . . . . . . . 8O-14
ANCHOR - INSTALLATION, CHILD
RESTRAINT . . . . . . . . . . . . . . . . . . . . . . . . . 8O-17
ANCHOR - OPERATION, CHILD
RESTRAINT . . . . . . . . . . . . . . . . . . . . . . . . . 8O-16
. 8O-16ANCHOR - REMOVAL, CHILD RESTRAINT ANCHOR & RIGHT OUTBOARD -
INSTALLATION, CENTER . . . . . . . . . . . . . . . 8O-45
ANCHOR & RIGHT OUTBOARD -
REMOVAL, CENTER . . . . . . . . . . . . . . . . . . . 8O-43
ANTENNA BODY & CABLE -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 8A-4
ANTENNA BODY & CABLE -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 8A-6
ANTENNA BODY & CABLE - OPERATION . . . 8A-4
ANTENNA BODY & CABLE - REMOVAL . . . . . 8A-6
ANTENNA BODY AND CABLE -DIAGNOSIS AND TESTING . . . . . . . . . . . . . . 8A-4
ANTENNA CABLE - INSTALLATION,
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . 8A-6
ANTILOCK - DIAGNOSIS AND TESTING,
REAR WHEEL . . . . . . . . . . . . . . . . . . . . . . . . 5-42
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
ANTILOCK BRAKE - OPERATION,
CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
ANTILOCK BRAKE - REMOVAL,
CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
A-PILLAR TRIM/GRAB HANDLE -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 23-64
A-PILLAR TRIM/GRAB HANDLE -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 23-64
A-PILLAR WEATHERSTRIP RETAINER -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 23-91
A-PILLAR WEATHERSTRIP RETAINER -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 23-91
APPLICATION TABLE, SPECIFICATIONS -
A/C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-7
AREA LEAKS - DIAGNOSIS AND
TESTING, REAR SEAL . . . . . . . . 9-135,9-204,9-64
ARM / ADJUSTER ASSEMBLY -
DESCRIPTION, ROCKER . . . . . . . . . . . . . . . 9-124
ARM / ADJUSTER ASSEMBLY -
REMOVAL, ROCKER . . . . . . . . . . . . . 9-124,9-249
ARM / ADJUSTER ASSY - CLEANING,
ROCKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-310
ARM / ADJUSTER ASSY - DESCRIPTION,
ROCKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-310
ARM / ADJUSTER ASSY - INSPECTION,
ROCKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-311
ARM / ADJUSTER ASSY -
INSTALLATION, ROCKER . . . . . 9-198,9-312,9-379
ARM / ADJUSTER ASSY - REMOVAL,
ROCKER . . . . . . . . . . . . . . . . . 9-198,9-310,9-379
ARM - DESCRIPTION, ROCKER . . . . . . 9-30,9-36
ARM - DESCRIPTION, WIPER . . . . . . . . . . . 8R-18
ARM - INSTALLATION, LOWERSUSPENSION . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
ARM - INSTALLATION, PITMAN . . . . . . . . . 19-36
ARM - INSTALLATION, ROCKER . . . . . . . . . . 9-30
ARM - INSTALLATION, UPPER CONTROL . . . 2-27
ARM - INSTALLATION, WIPER . . . . . . . . . . 8R-19
. . . . . . . . . . . . 8R-18
ARM - OPERATION, WIPER ARM - REMOVAL, LOWER SUSPENSION . . . 2-35
ARM - REMOVAL, PITMAN . . . . . . . . . . . . . 19-35
ARM - REMOVAL, ROCKER . . . . . . . . . . 9-30,9-36
ARM - REMOVAL, UPPER CONTROL . . . . . . 2-27
ARM - REMOVAL, WIPER . . . . . . . . . . . . . . 8R-18
ARM BUSHINGS - 2WD (LD) -INSTALLATION, LOWER CONTROL. . . . . . . . . . 2-14
ARM BUSHINGS - 2WD (LD) -
REMOVAL, LOWER CONTROL . . . . . . . . . . . . 2-12
ARM BUSHINGS - 4WD (LD) -
INSTALLATION, LOWER CONTROL . . . . . . . . 2-13
ARM BUSHINGS - 4WD (LD) -
REMOVAL, LOWER CONTROL . . . . . . . . . . . . 2-12
ARMREST / SEAT BACK - INSTALLATION,
CENTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-78
ARMREST / SEAT BACK - REMOVAL,
CENTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-77
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING . . . . . . . . . . . . . . . 8I-7
ASD SENSE - PCM INPUT - OPERATION . . . . 8I-6
ASH RECEIVER - INSTALLATION . . . . . . . . . 23-52
ASH RECEIVER - REMOVAL . . . . . . . . . . . . 23-51
AUDIO - DESCRIPTION . . . . . . . . . . . . . . . . . 8A-1
AUDIO - DIAGNOSIS AND TESTING . . . . . . . 8A-2
AUDIO - OPERATION . . . . . . . . . . . . . . . . . . . 8A-1
AUTOMATIC DAY / NIGHT MIRROR -DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 8N-12
AUTOMATIC DAY / NIGHT MIRROR -
DIAGNOSIS AND TESTING . . . . . . . . . . . . . 8N-12
AUTOMATIC DAY / NIGHT MIRROR -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8N-12
AUTOMATIC DAY / NIGHT MIRROR -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 8N-13
AUTOMATIC LOCKING RETRACTOR -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 8O-13
AUTOMATIC LOCKING RETRACTOR -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8O-14
AUTOMATIC TRANSMISSION -
AUTOMATIC TRANSMISSION -
45RFE/545RFE - OPERATION . . . . . . . . . . . 21-490
AUTOMATIC TRANSMISSION - 46RE -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . 21-131
AUTOMATIC TRANSMISSION - 46RE -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 21-133
AUTOMATIC TRANSMISSION - 48RE -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . 21-312
AUTOMATIC TRANSMISSION - 48RE -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 21-314
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING . . . . . . 21-139,21-320, 21-491
AUTOMATIC TRANSMISSION FLUID -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 0-4
AUTOMATIC TRANSMISSION FLUID -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5
AUXILIARY SPRING BUMPERS (3500) -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 2-40
AUXILIARY SPRING BUMPERS (3500) -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
AXLE - 10 1/2 AA - ADJUSTMENTS,
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-104
AXLE - 10 1/2 AA - DESCRIPTION, REAR . . 3-100
AXLE - 10 1/2 AA - DIAGNOSIS ANDTESTING, REAR . . . . . . . . . . . . . . . . . . . . . . 3-100
INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . 8A-7
45RFE/545RFE - DESCRIPTION . . . . . . . . . 21-489
AXLE - 10 1/2 AA - INSTALLATION,
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-103
AXLE - 10 1/2 AA - OPERATION, REAR . . . 3-100
AXLE - 10 1/2 AA - REMOVAL, REAR . . . . . 3-103
AXLE - 10 1/2 AA - SPECIAL TOOLS,REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-108
AXLE - 10 1/2 AA - SPECIFICATIONS,
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-108
AXLE - 11 1/2 AA - ADJUSTMENTS,
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-131
AXLE - 11 1/2 AA - DESCRIPTION, REAR . . 3-127
AXLE - 11 1/2 AA - DIAGNOSIS ANDTESTING, REAR . . . . . . . . . . . . . . . . . . . . . . 3-127
AXLE - 11 1/2 AA - INSTALLATION,
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-130
AXLE - 11 1/2 AA - OPERATION, REAR . . . 3-127
AXLE - 11 1/2 AA - REMOVAL, REAR . . . . . 3-130
AXLE - 11 1/2 AA - SPECIAL TOOLS,REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-135
AXLE - 11 1/2 AA - SPECIFICATIONS,
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-135
. . . . . 3-74
. . . . . . 3-69AXLE - 9 1/4 - ADJUSTMENTS, REAR AXLE - 9 1/4 - DESCRIPTION, REAR AXLE - 9 1/4 - DIAGNOSIS AND
TESTING, REAR . . . . . . . . . . . . . . . . . . . . . . . 3-69
AXLE - 9 1/4 - INSTALLATION, REAR . . . . . . 3-74
AXLE - 9 1/4 - OPERATION, REAR . . . . . . . . 3-69
AXLE - 9 1/4 - REMOVAL, REAR . . . . . . . . . . 3-74
AXLE - 9 1/4 - SPECIAL TOOLS, REAR . . . . . 3-80
AXLE - 9 1/4 - SPECIFICATIONS, REAR . . . . . . 3-79
AXLE - 9 1/4 AA - ADJUSTMENTS,FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49
AXLE - 9 1/4 AA - DESCRIPTION, FRONT . . . 3-45
AXLE - 9 1/4 AA - DIAGNOSIS ANDTESTING, FRONT . . . . . . . . . . . . . . . . . . . . . . 3-45
AXLE - 9 1/4 AA - INSTALLATION,
FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-48
. . . . 3-45
. . . . . . 3-48AXLE - 9 1/4 AA - OPERATION, FRONT AXLE - 9 1/4 AA - REMOVAL, FRONT AXLE - 9 1/4 AA - SPECIAL TOOLS,
FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53
AXLE - 9 1/4 AA - SPECIFICATIONS,
FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53
AXLE - C205F - ADJUSTMENTS, FRONT . . . . 3-21
AXLE - C205F - DESCRIPTION, FRONT . . . . . 3-18
AXLE - C205F - DIAGNOSIS ANDTESTING, FRONT . . . . . . . . . . . . . . . . . . . . . . 3-18
. . . . 3-21
AXLE - C205F - INSTALLATION, FRONT . . . . . . 3-18
AXLE - C205F - OPERATION, FRONT . . . . . . . . 3-21
AXLE - C205F - REMOVAL, FRONT AXLE - C205F - SPECIAL TOOLS, FRONT . . . 3-30
AXLE - C205F - SPECIFICATIONS, FRONT . . . 3-29
AXLE - DESCRIPTION . . . . . . . . . . . . . . . . . . . 0-4
AXLE BEARINGS - INSTALLATION . . 3-112,3-139, 3-34,3-84
AXLE BEARINGS - REMOVAL . . 3-112,3-138,3-33, 3-84
. 3-33,3-58, 3-84
. 3-33,3-58,3-84
AXLE SHAFT SEALS - REMOVAL AXLE SHAFTS - ASSEMBLY . . . . . . . . . . . . . 3-58
AXLE SHAFTS - DISASSEMBLY . . . . . . . . . . . 3-56
AXLE SHAFTS - INSTALLATION . . . . 3-111,3-138, 3-33,3-58,3-83
AXLE SHAFTS - REMOVAL . . . . 3-111,3-138,3-33, 3-56,3-83AXLE SHAFT SEALS - INSTALLATION
BACK - INSTALLATION, CENTER
ARMREST / SEAT . . . . . . . . . . . . . . . . . . . . 23-78
. . . . . 23-84
. . . . . . . . 23-84BACK - REAR - INSTALLATION, SEAT BACK - REAR - REMOVAL, SEAT BACK - REMOVAL, CENTER ARMREST /
SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-77
BACK CUSHION / COVER - FRONT -
INSTALLATION, SEAT . . . . . . . . . . . . . . . . . 23-83
BACK CUSHION / COVER - FRONT -
REMOVAL, SEAT . . . . . . . . . . . . . . . . . . . . . 23-83
BACK CUSHION / COVER - REAR -
INSTALLATION, SEAT . . . . . . . . . . . . . . . . . 23-85
BACK CUSHION / COVER - REAR -
REMOVAL, SEAT . . . . . . . . . . . . . . . . . . . . . 23-85
BACK HINGE - INSTALLATION, CENTER
SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-80
. . 23-79BACK HINGE - REMOVAL, CENTER SEAT BACK INERTIA HINGE COVER -
INSTALLATION, CENTER SEAT . . . . . . . . . . 23-78
BACK INERTIA HINGE COVER -
REMOVAL, CENTER SEAT . . . . . . . . . . . . . . 23-78
DR
Description
Group-Page
Description
Group-Page
Description
INDEX
Group-Page
BACK LID - INSTALLATION, CENTER
SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-80
. . . . 23-80BACK LID - REMOVAL, CENTER SEAT BACK PANEL TRIM - INSTALLATION,
REAR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . 23-70
BACK PANEL TRIM - REMOVAL, REAR
CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-70
BACK REAR - FOOTMANS LOOP
BRACKETS - INSTALLATION, SEAT . . . . . . . 23-85
BACK REAR - FOOTMANS LOOP
BRACKETS - REMOVAL, SEAT . . . . . . . . . . . 23-85
BACKLITE - INSTALLATION . . . . . . . . . . . . . 23-86
BACKLITE - REMOVAL . . . . . . . . . . . . . . . . . 23-86
BACKLITE VENT GLASS - INSTALLATION . . 23-87
BACKLITE VENT GLASS - REMOVAL . . . . . . 23-87
BACKUP LAMP - INSTALLATION . . . . . . . . . . 8L-7
BACKUP LAMP - REMOVAL . . . . . . . . . . . . . 8L-7
BACKUP LAMP SWITCH - DESCRIPTION . . . 8L-7
BACKUP LAMP SWITCH - DIAGNOSISAND TESTING . . . . . . . . . . . . . . . . . . . . . . . . 8L-8
BACKUP LAMP SWITCH - OPERATION . . . . . 8L-8
BALANCE - STANDARD PROCEDURE,TIRE AND WHEEL . . . . . . . . . . . . . . . . . . . . . 22-4
. . . . . . . . 9-79
. . . . . . . . . . . . 9-79BALANCE SHAFT - INSTALLATION BALANCE SHAFT - REMOVAL BALL JOINT - DIAGNOSIS AND TESTING,
LOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
BALL JOINT - DIAGNOSIS AND TESTING,
UPPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
BALL JOINT - INSTALLATION, LOWER . . 2-19,2-33
BALL JOINT - INSTALLATION, UPPER . . . . . 2-33
BALL JOINT - REMOVAL, LOWER . . . . . 2-18,2-32
BALL JOINT - REMOVAL, UPPER . . . . . . . . . 2-33
BAND OPERATION - DIAGNOSIS ANDTESTING, AIR TESTING TRANSMISSION CLUTCH . . . . . . . 21-143,21-324
BANDS - ADJUSTMENT . . . . . . . . . 21-193,21-374
BANDS - DESCRIPTION . . . . . . . . . 21-193,21-373
. . . . . . . . . . 21-193,21-374
BANDS - OPERATION BAR - DESCRIPTION, STABILIZER . . . . . . . . 2-24
BAR - DESCRIPTION, TORSION . . . . . . . . . . 2-25
BAR - INSTALLATION, STABILIZER . . . . 2-24,2-37
BAR - INSTALLATION, TORSION . . . . . . . . . . 2-26
BAR - INSTALLATION, TRACK . . . . . . . . . . . 19-37
BAR - OPERATION, STABILIZER . . . . . . . . . . 2-24
BAR - OPERATION, TORSION . . . . . . . . . . . . 2-25
BAR - REMOVAL, STABILIZER . . . . . . . 2-24,2-37
. . . . . . . . . . . . . 2-25
BAR - REMOVAL, TORSION BAR - REMOVAL, TRACK . . . . . . . . . . . . . . 19-37
BAR CROSS MEMBER BUSHING -INSTALLATION, TORSION . . . . . . . . . . . . . . . 2-14
BAR CROSSMEMBER BUSHING -
REMOVAL, TORSION . . . . . . . . . . . . . . . . . . . 2-12
BASE BRAKE, SPECIFICATIONS . . . . . . . . . . . . 5-7
BASE BRAKE SYSTEM - DIAGNOSIS ANDTESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
BASE BRAKES, SPECIAL TOOLS . . . . . . . . . . . 5-5
BASECOAT/CLEARCOAT FINISH -DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 23-74
BATTERIES - STANDARD PROCEDURE,
RKE TRANSMITTER . . . . . . . . . . . . . . . . . . . 8N-9
BATTERY - DESCRIPTION . . . . . . . . . . . . . . . 8F-7
. . . . . 8F-7
BATTERY - DIAGNOSIS AND TESTING BATTERY CABLES - DESCRIPTION . . . . . . . 8F-14
BATTERY CABLES - DIAGNOSIS ANDTESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 8F-15
BATTERY CABLES - INSTALLATION . . . . . . . 8F-17
BATTERY CABLES - OPERATION . . . . . . . . . 8F-14
BATTERY CABLES - REMOVAL . . . . . . . . . . 8F-16
BATTERY CHARGING - STANDARDPROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . 8F-8
BATTERY HOLDDOWN - DESCRIPTION . . . . 8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-14
. . . . . 8F-14
BATTERY HOLDDOWN - OPERATION BATTERY HOLDDOWN - REMOVAL . . . . . . . 8F-14
BATTERY SYSTEM - CLEANING . . . . . . . . . . . 8F-4
BATTERY SYSTEM - DESCRIPTION . . . . . . . . 8F-1
BATTERY SYSTEM - DIAGNOSIS ANDTESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8F-2
BATTERY SYSTEM - INSPECTION . . . . . . . . . 8F-6
BATTERY SYSTEM - OPERATION . . . . . . . . . 8F-2
BATTERY SYSTEM - SPECIFICATIONS . . . . . . 8F-6
BATTERY SYSTEM SPECIAL TOOLS,SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . 8F-7
BATTERY TEMPERATURE SENSOR -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 8F-21
BATTERY TEMPERATURE SENSOR -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 8F-21
BATTERY TEMPERATURE SENSOR -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8F-21
BATTERY TEMPERATURE SENSOR -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 8F-21
BATTERY TESTER - STANDARD
PROCEDURE, USING MICRO 420 . . . . . . . . 8F-12
BATTERY TRAY - DESCRIPTION . . . . . . . . . 8F-17
BATTERY TRAY - INSTALLATION . . . . . . . . . 8F-18
BATTERY TRAY - OPERATION . . . . . . . . . . . 8F-17
BATTERY TRAY - REMOVAL . . . . . . . . . . . . 8F-17
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-27
BEAM INDICATOR - OPERATION, HIGH . . . . 8J-28
BEARING - ADJUSTMENTS, CENTER . . . . . . . 3-8
BEARING - FITTING - STANDARDPROCEDURE, CRANKSHAFT MAIN . . 9-133,9-202
BEARING - INSTALLATION, CENTER . . . . . . . . 3-8
BEARING - INSTALLATION, CLUTCHRELEASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
BEARING - INSTALLATION, HUB . . . . . . . . . . 2-31
BEARING - INSTALLATION, OUTPUTSHAFT FRONT . . . . . . . . . . . . . . . . 21-217,21-395
BEARING - INSTALLATION, OUTPUT
SHAFT REAR . . . . . . . . . . . . . . . . . 21-217,21-396
. . . . . . . . 6-12
BEARING - INSTALLATION, PILOT BEARING - REMOVAL, CENTER . . . . . . . . . . . 3-8
BEARING - REMOVAL, CLUTCH RELEASE . . . 6-11
BEARING - REMOVAL, HUB . . . . . . . . . . . . . 2-30
BEARING - REMOVAL, OUTPUT SHAFTFRONT . . . . . . . . . . . . . . . . . . . . . . 21-217,21-395
BEARING - REMOVAL, OUTPUT SHAFT
REAR . . . . . . . . . . . . . . . . . . . . . . . 21-217,21-395
. . . . . . . . . . . . 6-12BEARING - REMOVAL, PILOT BEARING AND CRANKSHAFT JOURNAL
CLEARANCE - STANDARD PROCEDURE, CONNECTING ROD . . . . . . . . 9-321
BEARING CLEARANCE - STANDARD
BELT & RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT . . . . . . . . . . . . . . . . . . . . 8O-41
BELT BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT . . . . . . . . . . . . . . . . . . . . 8O-34
BELT BUCKLE - REMOVAL, FRONT
OUTBOARD SEAT . . . . . . . . . . . . . . . . . . . . 8O-33
BELT MOLDING - INSTALLATION, FRONT
DOOR INNER . . . . . . . . . . . . . . . . . . . . . . . . 23-93
BELT MOLDING - INSTALLATION, FRONT
DOOR OUTER . . . . . . . . . . . . . . . . . . . . . . . 23-93
BELT MOLDING - INSTALLATION, REAR
DOOR INNER . . . . . . . . . . . . . . . . . . . . . . . . 23-94
BELT MOLDING - INSTALLATION, REAR
DOOR OUTER . . . . . . . . . . . . . . . . . . . . . . . 23-94
BELT MOLDING - REMOVAL, FRONT
DOOR INNER . . . . . . . . . . . . . . . . . . . . . . . . 23-93
BELT MOLDING - REMOVAL, FRONT
DOOR OUTER . . . . . . . . . . . . . . . . . . . . . . . 23-93
BELT MOLDING - REMOVAL, REAR
DOOR INNER . . . . . . . . . . . . . . . . . . . . . . . . 23-94
BELT MOLDING - REMOVAL, REAR
DOOR OUTER . . . . . . . . . . . . . . . . . . . . . . . 23-94
. . . . . 8O-46BELT SWITCH - DESCRIPTION, SEAT BELT SWITCH - DIAGNOSIS AND
TESTING, SEAT . . . . . . . . . . . . . . . . . . . . . . 8O-47
BELT SWITCH - OPERATION, SEAT . . . . . . . 8O-46
BELT TENSION REDUCER -DESCRIPTION, SEAT . . . . . . . . . . . . . . . . . . 8O-48
BELT TENSION REDUCER - DIAGNOSIS
AND TESTING, SEAT . . . . . . . . . . . . . . . . . . 8O-49
BELT TENSION REDUCER - OPERATION,
SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8O-49
BELT TENSIONER - DESCRIPTION, SEAT . . . . 8O-47
BELT TENSIONER - OPERATION, SEAT . . . . 8O-48
BELT TENSIONERS - 3.7L / 4.7L -DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 7-22
PROCEDURE, MAIN . . . . . . . . . . . . . . . . . . . 9-322
BELT TENSIONERS - 3.7L / 4.7L -
BEARING FITTING - STANDARD
PROCEDURE, CONNECTING ROD . . . 9-128,9-251, 9-382
BEARING FITTING - STANDARD
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 7-23
BELT TENSIONERS - 3.7L / 4.7L -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
BELT TENSIONERS - 3.7L / 4.7L -
PROCEDURE, CRANKSHAFT MAIN . . . . . . . 9-253
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
BEARING FITTING, STANDARD
BELT TENSIONERS - 5.9L -
PROCEDURE - CONNECTING ROD . . . . . . . . 9-48
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 7-23
BEARING FITTING, STANDARD
PROCEDURE - MAIN . . . . . . . . . . . . . . . . . . . 9-43
BEARINGS - DESCRIPTION,
CRANKSHAFT MAIN . . . . . . . . . . . . . . . . . . 9-253
BEARINGS - INSPECTION, CRANKSHAFT
MAIN . . . . . . . . . . . . . . . . . . . . . . . . . 9-133,9-203
BEARINGS - INSTALLATION, AXLE . . 3-112,3-139, 3-34,3-84
. . 9-320, 9-381BEARINGS - INSTALLATION, CAMSHAFT
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN . . . . . . . . . . . . . 9-254,9-383
BEARINGS - INSTALLATION,
DIFFERENTIAL CASE . 3-121,3-148,3-39,3-65,3-94
BEARINGS - OPERATION, CRANKSHAFT
BEARINGS - REMOVAL, AXLE
MAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-253
. 3-112,3-138,3-33, 3-84
. 9-317,9-380BEARINGS - REMOVAL, CAMSHAFT BEARINGS - REMOVAL, CRANKSHAFT
MAIN . . . . . . . . . . . . . . . . . . . . . . . . . 9-254,9-383
BEARINGS - REMOVAL, DIFFERENTIAL
CASE . . . . . . . . . . . . . 3-121,3-148,3-39,3-64,3-93
BEARINGS - STANDARD PROCEDURE,
FITTING CRANKSHAFT MAIN . . . . . . . . . . . 9-383
BELT / CHAIN COVER(S) -
INSTALLATION, TIMING . 9-169,9-278,9-404,9-81
BELT / CHAIN COVER(S) - REMOVAL,
TIMING . . . . . . . . . . . . . . 9-168,9-278,9-404,9-80
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE . . . . . . . . . . . . 7-25,7-28,7-31
BELT - INSTALLATION, FRONT CENTER
SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8O-27
. . 8O-26BELT - REMOVAL, FRONT CENTER SEAT BELT & RETRACTOR - INSTALLATION,
FRONT CENTER SEAT . . . . . . . . . . . . . . . . . 8O-26
BELT & RETRACTOR - INSTALLATION,
REAR CENTER SEAT . . . . . . . . . . . . . . . . . . 8O-40
BELT & RETRACTOR - INSTALLATION,
REAR OUTBOARD SEAT . . . . . . . . . . . . . . . 8O-42
BELT & RETRACTOR - REMOVAL, FRONT
CENTER SEAT . . . . . . . . . . . . . . . . . . . . . . . 8O-25
BELT & RETRACTOR - REMOVAL, REAR
CENTER SEAT . . . . . . . . . . . . . . . . . . . . . . . 8O-39
BELT TENSIONERS - 5.9L -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 7-24
BELT TENSIONERS - 5.9L - OPERATION . . . . 7-23
BELT TENSIONERS - 5.9L - REMOVAL . . . . . 7-23
BELT TENSIONERS - 5.9L DIESEL -DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 7-24
BELT TENSIONERS - 5.9L DIESEL -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 7-25
BELT TENSIONERS - 5.9L DIESEL -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24
BELT TENSIONERS - 5.9L DIESEL -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT . . . . . . . . . . . . . . . . . 8O-50
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT . . . . . . . . . . . . . . . . . . . . . 8O-50
BELT/CHAIN AND SPROCKETS -
INSPECTION, TIMING . . . . . . . . . . . . . 9-171,9-83
BELT/CHAIN AND SPROCKETS -
INSTALLATION, TIMING . 9-172,9-279,9-406,9-84
BELT/CHAIN AND SPROCKETS -
REMOVAL, TIMING . . . . . 9-169,9-279,9-405,9-81
BELTS - 3.7L / 4.7L - INSTALLATION,
DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
BELTS - 3.7L / 4.7L - REMOVAL, DRIVE . . . . 7-27
. . . . . 7-31
BELTS - 5.9L - INSTALLATION, DRIVE BELTS - 5.9L - REMOVAL, DRIVE . . . . . . . . . 7-30
BELTS - 5.9L DIESEL - INSTALLATION,DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34
BELTS - 5.9L DIESEL - REMOVAL, DRIVE . . 7-34
BEZEL - INSTALLATION, CLUSTER . . . . . . . 23-50
BEZEL - INSTALLATION, INSTRUMENTPANEL CENTER . . . . . . . . . . . . . . . . . . . . . . 23-58
BEZEL - INSTALLATION, INSTRUMENT
PANEL DRIVER SIDE . . . . . . . . . . . . . . . . . . 23-59
BEZEL - INSTALLATION, INSTRUMENT
PANEL HEADLAMP SWITCH . . . . . . . . . . . . 23-57
BEZEL - REMOVAL, CLUSTER . . . . . . . . . . . 23-50
BEZEL - REMOVAL, INSTRUMENT PANELCENTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-58
BEZEL - REMOVAL, INSTRUMENT PANEL
DRIVER SIDE . . . . . . . . . . . . . . . . . . . . . . . . 23-58
BEZEL - REMOVAL, INSTRUMENT PANEL
HEADLAMP SWITCH . . . . . . . . . . . . . . . . . . 23-57
4
INDEX
Description
Group-Page
Description
Group-Page
Description
Group-Page
DR
. . . . . . . . . 23-62
BLOWER MOTOR SWITCH -
BIN - INSTALLATION, STORAGE BIN - INSTALLATION, UNDER SEAT
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-81
BIN - REMOVAL, STORAGE . . . . . . . . . . . . . 23-62
BIN - REMOVAL, UNDER SEAT STORAGE . . 23-81
BIN COVERING - INSTALLATION, UNDERSEAT STORAGE . . . . . . . . . . . . . . . . . . . . . . 23-81
BIN COVERING - REMOVAL, UNDER
SEAT STORAGE . . . . . . . . . . . . . . . . . . . . . . 23-81
BIN LATCH - INSTALLATION, UNDER
SEAT STORAGE . . . . . . . . . . . . . . . . . . . . . . 23-81
BIN LATCH - REMOVAL, UNDER SEAT
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-81
BLADE - DESCRIPTION, WIPER . . . . . . . . . 8R-19
BLADE - INSTALLATION, WIPER . . . . . . . . . 8R-20
BLADE - OPERATION, WIPER . . . . . . . . . . . 8R-19
BLADE - REMOVAL, WIPER . . . . . . . . . . . . 8R-19
BLEEDING - STANDARD PROCEDURE . . . . . . 5-27
BLEEDING - STANDARD PROCEDURE,ABS BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
BLEEDING - STANDARD PROCEDURE,
MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER . . . . . . . . . . . . . . . . . . . 5-20
BLEEDING - STANDARD PROCEDURE,
PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
BLEND DOOR - INSTALLATION . . . . . . . . . . 24-25
BLEND DOOR - REMOVAL . . . . . . . . . . . . . 24-24
BLEND DOOR ACTUATOR -DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 24-16
BLEND DOOR ACTUATOR -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 24-17
BLEND DOOR ACTUATOR - OPERATION . . . 24-16
BLEND DOOR ACTUATOR - REMOVAL . . . . 24-17
. 9-127,9-200,9-249, BLOCK - CLEANING, ENGINE 9-38,9-380BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR . . . . . . . . . . . . . . . . . . . 24-17
BLOCK - DESCRIPTION, ENGINE . . . . . 9-126,9-37
. . . . 9-127,9-200, BLOCK - INSPECTION, ENGINE 9-249,9-38,9-380BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR . . . . . . . . . . . . . . . . . . . 24-18
BLOCK - INSTALLATION, BRAKE
JUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 24-17
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 24-18
. . . . 5-19BLOCK - REMOVAL, BRAKE JUNCTION BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION, ENGINE . . . . . . . . . . . . . . . . . 7-43
BLOCK HEATER - 5.9L DIESEL -
INSTALLATION, ENGINE . . . . . . . . . . . . . . . . 7-44
BLOCK HEATER - 5.9L DIESEL -
OPERATION, ENGINE . . . . . . . . . . . . . . . . . . . 7-43
BLOCK HEATER - 5.9L DIESEL -
REMOVAL, ENGINE . . . . . . . . . . . . . . . . . . . . 7-43
BLOCK HEATER - DESCRIPTION, ENGINE . . . 7-42
BLOCK HEATER - DIAGNOSIS ANDTESTING, ENGINE . . . . . . . . . . . . . . . . . . . . . 7-42
BLOCK HEATER - INSTALLATION,
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-43
. . . . 7-42
. . . . . . 7-43BLOCK HEATER - OPERATION, ENGINE BLOCK HEATER - REMOVAL, ENGINE BLOCK REFACING - STANDARD
PROCEDURE, CYLINDER . . . . . . . . . . . . . . . 9-312
. . . . . . . 24-25BLOWER MOTOR - DESCRIPTION BLOWER MOTOR - DIAGNOSIS AND
TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-26
BLOWER MOTOR - INSTALLATION . . . . . . . 24-26
BLOWER MOTOR - OPERATION . . . . . . . . . 24-25
BLOWER MOTOR - REMOVAL . . . . . . . . . . . 24-26
BLOWER MOTOR RESISTOR -DIAGNOSIS AND TESTING . . . . . . . . . . . . . 24-18
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 24-17
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 24-18
BLOWER MOTOR RESISTOR BLOCK -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 24-17
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 24-18
BLOWER MOTOR SWITCH -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 24-18
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING . . . . . . . . . . . . . . . . . . . . . . . 24-18
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . 23-99
BRAKE BOOSTER - INSTALLATION,
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 24-19
BLOWER MOTOR SWITCH - OPERATION . . 24-18
. . . 24-19
BLOWER MOTOR SWITCH - REMOVAL BODY - ADJUSTMENTS, VALVE . . 21-308,21-487
BODY - ASSEMBLY, VALVE . . . . . . 21-299,21-477, 21-590BODY & CABLE - DESCRIPTION,
ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . 8A-4
BODY & CABLE - INSTALLATION,
BODY - DISASSEMBLY, VALVE
BODY - DESCRIPTION, THROTTLE BODY - DESCRIPTION, VALVE
ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . 8A-6
BODY & CABLE - OPERATION, ANTENNA . . . 8A-4
. . . . 8A-6
BODY & CABLE - REMOVAL, ANTENNA . . . . . . 21-298,21-476, BODY - CLEANING, VALVE 21-588
. . . . . . . 14-45
. . . 21-267,21-445, 21-584
. . . 21-287,21-465, 21-586
. . . . 21-298,21-476, 21-588
BODY - INSTALLATION, THROTTLE . . . . . . . 14-47
BODY - INSTALLATION, VALVE . . . 21-307,21-486, 21-590
. . . . . . . . . 14-45
. . . . . 21-272,21-450, 21-585
BODY - REMOVAL, THROTTLE . . . . . . . . . . 14-45
BODY - REMOVAL, VALVE . 21-286,21-464,21-585
BODY AND CABLE - DIAGNOSIS ANDBODY - OPERATION, THROTTLE BODY - OPERATION, VALVE
BODY - INSPECTION, VALVE
TESTING, ANTENNA . . . . . . . . . . . . . . . . . . . 8A-4
BODY CODE PLATE - DESCRIPTION . . . . . Intro.-4
BODY ISOLATORS - INSTALLATION . . . . . . 23-37
BODY ISOLATORS - REMOVAL . . . . . . . . . . 23-36
BODY LUBRICATION - STANDARDPROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . 23-3
BODY OPENING DIMENSIONS -
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC . . . . . . . . . . . . . . . . . 23-3
. . 23-36
BODY SIDE MOLDINGS - INSTALLATION BODY SIDE MOLDINGS - REMOVAL . . . . . . 23-36
BODY, SPECIAL TOOLS . . . . . . . . . . . . . . . . 23-14
. . . . . . . . . . . 23-72
BODY VENT - INSTALLATION BODY VENT - REMOVAL . . . . . . . . . . . . . . . 23-72
BOOST PRESSURE - DIAGNOSIS ANDTESTING, TURBOCHARGER . . . . . . . . . . . . . 11-10
BOOSTER - DESCRIPTION, POWER
BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER . . . . . . . . . . . . . 5-20
BOOSTER - INSTALLATION, HYDRO-
BOOST BRAKE . . . . . . . . . . . . . . . . . . . . . . . . 5-27
BOOSTER - INSTALLATION, POWER
BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
. . . 5-25BOOSTER - OPERATION, POWER BRAKE BOOSTER - REMOVAL, HYDRO-BOOST
BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
. . . . 5-25BOOSTER - REMOVAL, POWER BRAKE BOOT - INSTALLATION, 4WD FLOOR
SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-64
BOOT - INSTALLATION, EXTENSION
HOUSING SEAL AND DUST . . . . . . 21-652,21-716
BOOT - REMOVAL, 4WD FLOOR SHIFT . . . . 23-63
BOOT - REMOVAL, EXTENSION HOUSINGSEAL AND DUST . . . . . . . . . . . . . . 21-652,21-716
BORE - DE-GLAZE - STANDARD
PROCEDURE, CYLINDER . . . . . . . . . . . . . . . 9-313
BORE HONING - STANDARD
PROCEDURE, CYLINDER . 9-126,9-233,9-360,9-37
BORE REPAIR - STANDARD
PROCEDURE, CAM . . . . . . . . . . . . . . . . . . . 9-315
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER . . . . . . . . . . . . . . . 9-313
BOX - INSTALLATION, CARGO . . . . . . . . . . 23-37
BOX - INSTALLATION, GLOVE . . . . . . . . . . . 23-53
BOX - REMOVAL, CARGO . . . . . . . . . . . . . . 23-37
BOX - REMOVAL, GLOVE . . . . . . . . . . . . . . 23-53
BOX - TIE DOWN - INSTALLATION,CARGO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-37
BOX - TIE DOWN - REMOVAL, CARGO . . . . 23-37
BOX LAMP/SWITCH - INSTALLATION,GLOVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8L-25
. . 8L-25
. . . . . 23-53BOX LAMP/SWITCH - REMOVAL, GLOVE BOX LATCH - INSTALLATION, GLOVE
BOX LATCH - REMOVAL, GLOVE . . . . . . . . . 23-53
B-PILLAR GRAB HANDLE -INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 23-69
B-PILLAR GRAB HANDLE - REMOVAL . . . . 23-69
B-PILLAR LOWER TRIM - INSTALLATION . . 23-65
B-PILLAR LOWER TRIM - REMOVAL . . . . . 23-64
B-PILLAR UPPER TRIM - INSTALLATION . . 23-65
B-PILLAR UPPER TRIM - REMOVAL . . . . . . 23-65
BRACKET - INSTALLATION, REARVIEWMIRROR SUPPORT . . . . . . . . . . . . . . . . . . . 23-71
BRACKET - INSTALLATION, STEERING
COLUMN OPENING SUPPORT . . . . . . . . . . . 23-62
BRACKET - REMOVAL, STEERING
COLUMN OPENING SUPPORT . . . . . . . . . . . 23-61
BRACKETS - INSTALLATION, SEAT BACK
REAR - FOOTMANS LOOP . . . . . . . . . . . . . . 23-85
BRACKETS - REMOVAL, SEAT BACK
REAR - FOOTMANS LOOP . . . . . . . . . . . . . . 23-85
BRAKE - CLEANING, REAR DRUM IN
HAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
. . . . . . . . 5-30BRAKE - DESCRIPTION, PARKING BRAKE - INSPECTION, REAR DRUM IN
HAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
BRAKE - OPERATION, CONTROLLER
ANTILOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
BRAKE - OPERATION, PARKING . . . . . . . . . . 5-30
BRAKE - REMOVAL, CONTROLLERANTILOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . 8E-3
BRAKE BLEEDING - STANDARD
PROCEDURE, ABS . . . . . . . . . . . . . . . . . . . . . 5-40
BRAKE BOOSTER - DESCRIPTION,
POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
BRAKE BOOSTER - INSTALLATION,
HYDRO-BOOST . . . . . . . . . . . . . . . . . . . . . . . 5-27
POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
BRAKE BOOSTER - OPERATION, POWER . . . 5-25
BRAKE BOOSTER - REMOVAL,HYDRO-BOOST . . . . . . . . . . . . . . . . . . . . . . . 5-27
. . . . 5-25BRAKE BOOSTER - REMOVAL, POWER BRAKE CABLE - INSTALLATION, FRONT
PARKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
BRAKE CABLE - INSTALLATION, REAR
PARK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
BRAKE CABLE - REMOVAL, FRONT
PARKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
. . . 5-31BRAKE CABLE - REMOVAL, REAR PARK BRAKE CALIPER ADAPTER MOUNT -
INSTALLATION, DISC . . . . . . . . . . . . . . . . . . . 5-17
BRAKE CALIPERS - DESCRIPTION, DISC . . . 5-11
BRAKE CALIPERS - OPERATION, DISC . . . . . 5-12
BRAKE FLUID CONTAMINATION -DIAGNOSIS AND TESTING . . . . . . . . . . . . . . 5-18
BRAKE FLUID LEVEL - STANDARD
PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
BRAKE FLUID, SPECIFICATIONS . . . . . . . . . . 5-18
BRAKE HOSE - INSTALLATION, FRONT . . . . . . 5-9
BRAKE HOSE - INSTALLATION, REAR . . . . . . . 5-9
BRAKE HOSE - REMOVAL, REAR . . . . . . . . . . 5-8
BRAKE INDICATOR - DESCRIPTION,BRAKE/PARK . . . . . . . . . . . . . . . . . . . . . . . . 8J-18
BRAKE INDICATOR - DIAGNOSIS AND
TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 8J-19
BRAKE INDICATOR - OPERATION,
BRAKE/PARK . . . . . . . . . . . . . . . . . . . . . . . . 8J-19
BRAKE JUNCTION BLOCK -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5-19
BRAKE JUNCTION BLOCK - REMOVAL . . . . . 5-19
BRAKE LAMP - INSTALLATION . . . . . . . . . . . 8L-8
BRAKE LAMP - REMOVAL . . . . . . . . . . . . . . . 8L-8
BRAKE LAMP SWITCH - DESCRIPTION . . . . 8L-8
BRAKE LAMP SWITCH - DIAGNOSISAND TESTING . . . . . . . . . . . . . . . . . . . . . . . . 8L-9
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-10
BRAKE LAMP SWITCH - OPERATION . . . . . . 8L-8
. . . . . . . 8L-9
BRAKE LAMP SWITCH - REMOVAL . . . . . 5-10
BRAKE PADS/SHOES - INSTALLATION BRAKE PADS/SHOES - REMOVAL . . . . . . . . . 5-10
BRAKE PROPORTIONING -DESCRIPTION, ELECTRONIC VARIABLE . . . . 5-43
BRAKE PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE . . . . . . . . . . . . . . . . 5-43
. . 5-34
. . . . . . . . . . 5-7BRAKE SHOES - ADJUSTMENT, PARKING BRAKE, SPECIFICATIONS - BASE
DR
Description
Group-Page
Description
Group-Page
Description
INDEX
Group-Page
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE . . . . . . . . . . . . . . . . . . . . . . . . 5-2
BRAKE TRANSMISSION SHIFT
INTERLOCK - ADJUSTMENTS . . . 21-195,21-376, 21-540
BRAKE TRANSMISSION SHIFT
INTERLOCK - DIAGNOSIS AND TESTING . . . . . . . . . . . . . . 21-195,21-375,21-540
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION . . . 21-194, 21-375,21-540
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION . . . . . 21-194, 21-375,21-540
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 8J-18
BRAKE/PARK BRAKE INDICATOR -
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8J-19
BRAKES - ABS - DESCRIPTION . . . . . . . . . . . 5-39
. . . . . . . . . . . . 5-39
BRAKES - ABS - OPERATION BRAKES, SPECIAL TOOLS - BASE . . . . . . . . . 5-5
BREAK-IN - STANDARD PROCEDURE,A/C COMPRESSOR CLUTCH . . . . . . . . . . . . 24-10
BREATHER - INSTALLATION,
CRANKCASE . . . . . . . . . . . . . . . . . . . . . . . . 9-292
. . . . . 9-291BREATHER - REMOVAL, CRANKCASE BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT BELT . . . . . . . . . . . . . . . . 8O-34
BUCKLE - REMOVAL, FRONT OUTBOARD
SEAT BELT . . . . . . . . . . . . . . . . . . . . . . . . . 8O-33
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . 8F-10
. . . . . . . . 13-2
BUMPER - INSTALLATION, FRONT . . . . . . . 2-40
BUMPER - INSTALLATION, JOUNCE BUMPER - INSTALLATION, REAR . . . . . . . . . 13-4
BUMPER - REMOVAL, FRONT . . . . . . . . . . . . 13-2
BUMPER - REMOVAL, JOUNCE . . . . . . . . . . . 2-40
BUMPER - REMOVAL, REAR . . . . . . . . . . . . . 13-4
BUMPERS (3500) - INSTALLATION,AUXILIARY SPRING . . . . . . . . . . . . . . . . . . . . 2-40
BUMPERS (3500) - REMOVAL,
AUXILIARY SPRING . . . . . . . . . . . . . . . . . . . . 2-40
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF . . . . 21-201,21-381,21-541
. . . . . . . . . . . . . 19-18BUSHING - INSTALLATION BUSHING - INSTALLATION,
DISTRIBUTOR . . . . . . . . . . . . . . . . . . . . . . . 9-258
BUSHING - INSTALLATION, EXTENSION
HOUSING . . . . . . . . . . . . . . . . . . . . . . . . . . 21-200
BUSHING - INSTALLATION, TORSION
BAR CROSS MEMBER . . . . . . . . . . . . . . . . . . 2-14
BUSHING - REMOVAL . . . . . . . . . . . . . . . . . 19-18
BUSHING - REMOVAL, DISTRIBUTOR . . . . . 9-258
BUSHING - REMOVAL, EXTENSIONHOUSING . . . . . . . . . . . . . . . . . . . . . . . . . . 21-200
BUSHING - REMOVAL, TORSION BAR
CROSSMEMBER . . . . . . . . . . . . . . . . . . . . . . 2-12
BUSHING AND SEAL - INSTALLATION,
EXTENSION HOUSING . . . . . . . . . . 21-616,21-682
BUSHING AND SEAL - REMOVAL,
