Login- Download PDF Manual
-
The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.
376 MAINTAINING YOUR VEHICLE
NOTE: For best access to the oil filter, a drive on hoist should be used instead of a chassis hoist (3.7L Only). Engine Oil Filter Selection All of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine oil filters are high quality oil filters and are recommended. Engine Air Cleaner Filter Refer to the Maintenance Schedule in Section 8 for the proper maintenance intervals.
WARNING!
The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine air cleaner filters are a high quality filter and are recommended.
Maintenance-Free Battery The top of the maintenance-free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required.
WARNING!
• Battery acid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in your face or on your skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other.
(Continued)
MAINTAINING YOUR VEHICLE 377
WARNING! (Continued)
• Battery posts, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling the battery.
CAUTION!
It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage.
378 MAINTAINING YOUR VEHICLE
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.
WARNING!
• Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information Book for additional warranty information.
(Continued)
WARNING! (Continued)
• The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman.
Refrigerant Recovery and Recycling R-134a air conditioning refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C system sealers, stop leak products, seal conditioners, compressor oil, and refrigerants.
Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease such as MOPAR威 Spray White Lube to assure quiet, easy opera- tion and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching compo- nents to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant such as MOPAR威 Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE 379
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Adding Washer Fluid The fluid reservoir in the engine compartment should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent/antifreeze (not radiator antifreeze). Operate the system for a few seconds to flush out the residual water.
380 MAINTAINING YOUR VEHICLE
WARNING!
Commercial windshield washer solvents are flam- mable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system or if the exhaust fumes can be detected inside the vehicle or when the underside or rear of the vehicle is damaged, have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams
or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required. The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the converter as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
CAUTION!
WARNING!
MAINTAINING YOUR VEHICLE 381
Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn OFF the engine and allow it to cool. Service, including a tune up to manufacturer’s specifica- tions, should be obtained immediately.
382 MAINTAINING YOUR VEHICLE
To minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing. • Do not idle the engine for prolonged periods during very rough idle or malfunctioning operating condi- tions.
vehicle.
• Do not allow vehicle to run out of fuel.
Intentional tampering with emissions control in civil penalties being assessed
NOTE: systems can result against you. Cooling System
WARNING!
You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.
Engine Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check the front of the A/C condenser (if equipped) or radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the A/C con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of
MAINTAINING YOUR VEHICLE 383
engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly, the engine coolant (anti- freeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to the Maintenance Schedule in Section 8 for the proper maintenance intervals. Selection of Engine Coolant Use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- ine Parts” in this section for the correct fluid type.
384 MAINTAINING YOUR VEHICLE
CAUTION!
• Mixing of engine coolant (antifreeze) other than the specified HOAT engine coolant (antifreeze) may result in decreased corrosion protection and engine damage. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the engine coolant (antifreeze) and may plug the radiator.
(Continued)
CAUTION! (Continued)
• This vehicle has not been designed for use with (anti- propylene glycol based engine coolant freeze). Use of propylene glycol based engine coolant (antifreeze) is not recommended.
Adding Engine Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).
When adding engine coolant (antifreeze): • The manufacturer
recommends using MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below -34°F (-37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/antifreeze (cool- ant) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
MAINTAINING YOUR VEHICLE 385
Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent the loss of engine coolant (antifreeze) and to ensure that the engine coolant (antifreeze) will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
386 MAINTAINING YOUR VEHICLE
WARNING!
• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pres- sure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.
Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal
rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling and warm to normal operating temperature, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing the engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month.
When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine
MAINTAINING YOUR VEHICLE 387
coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent engine coolant (antifreeze) additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also.
bottle hoses are not kinked or obstructed.
388 MAINTAINING YOUR VEHICLE
• Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mile- age, and increased emissions.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the Maintenance Schedule in Section 8 for the proper maintenance intervals.
WARNING!
Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services or immediately if the BRAKE warning light shows system failure. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
WARNING!
• Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
CAUTION!
Do not allow petroleum-based fluid to contaminate the brake fluid. Seal damage will result.
MAINTAINING YOUR VEHICLE 389
Automatic Transmission
Fluid Level Check — 42RLE (3.7L Engine) Your vehicle is equipped with a capped transmission oil fill tube. It is sealed and should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly. Fluid Level Check — W5A580 (4.0L Engine) Your vehicle is equipped with a capped transmission oil fill tube. It is sealed and should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly.
390 MAINTAINING YOUR VEHICLE
Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturer’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
CAUTION!
Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in this sec- tion for the correct fluid type.
Special Additives The manufacturer strongly recommends against the ad- dition of any additives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. The use of transmission sealers should be avoided as they may adversely affect seals. Transfer Case
Fluid Level Check The fluid level should be to the bottom edge of the fill hole (A) when the vehicle is in a level position.
MAINTAINING YOUR VEHICLE 391
CAUTION!
When replacing plugs, do not overtighten. You could damage them and cause them to leak.
Selection of Lubricant Use only manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Front/Rear Axle Fluid
Fluid Level Check Lubricant should be at bottom edge of the oil fill hole.
Adding Fluid Fluid should be added only at filler hole until fluid begins to run out of the hole. Drain First remove fill plug (B), then drain plug (C). Recom- mended tightening torque for drain and fill plugs is 15–25 ft lbs (20–34 N·m).
392 MAINTAINING YOUR VEHICLE
Adding Fluid Add lubricant only at the fill hole and only to the level specified above. Selection of Lubricant Use only manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Appearance Care And Protection From Corrosion
Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme
hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.
Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
MAINTAINING YOUR VEHICLE 393
CAUTION!
• Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and liftgate are kept clear and open.
394 MAINTAINING YOUR VEHICLE
• If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.
mud or stone shields behind each wheel.
Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use MOPAR威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only MOPAR威 cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. YES Essentials威 Fabric Cleaning Procedure – If Equipped YES Essentials威 seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel.
with a clean, dry towel.
• For tough stains, apply MOPAR威 Total Clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essen-
tials威 products.
Interior Care Use MOPAR威 Total Clean to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with MOPAR威 Total Clean, then MOPAR威 Spot & Stain Remover if absolutely necessary. Do not use harsh cleaners or Armorall. Use MOPAR威 Total Clean to clean vinyl upholstery.
MAINTAINING YOUR VEHICLE 395
WARNING!
Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.
396 MAINTAINING YOUR VEHICLE
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth. Seat Belt Maintenance Do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the seat belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the seat belts from the vehicle to wash them.
Replace the seat belts if they appear frayed or worn or if the buckles do not work properly.
FUSES
Totally Integrated Power Module The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. This center contains cartridge fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover.
J3
J4
J5
J6
J7
J8
J9
J10
Totally Integrated Power Module (TIPM)
Cavity Cartridge
J1
J2
Fuse 40 Amp Green 30 Amp Pink
Mini- Fuse
Description
Power Folding Seat
Transfer Case/Pwr Liftgate Module
Cavity Cartridge
MAINTAINING YOUR VEHICLE 397
Mini- Fuse
Description
Rear Door Module (RR DOOR NODE) Driver Door Node
Passenger Door Node
Anti-Lock Brake Sys- tem (ABS) Pump/ESP Anti-Lock Brake Sys- tem (ABS) Valve/ESP Power Memory Seat (If Equipped) PZEV Motor/Flex Fuel
Hdlp Wash Relay/ Manual Tuning Valve
Fuse 40 Amp Green 25 Amp Natural 25 Amp Natural 40 Amp Green 30 Amp Pink 40 Amp Green 40 Amp Green 30 Amp Pink
398 MAINTAINING YOUR VEHICLE
Cavity Cartridge
Mini- Fuse
Description
Cavity Cartridge
J11
J13
J14
J15
J17
J18
J19
J20
Fuse 30 Amp Pink
60 Amp Yellow 40 Amp Green 30 Amp Pink 40 Amp Green 20 Amp Yellow
60 Amp Yellow 30 Amp Pink
Sway Bar/ THATCHAM Lock- Unlock/Power Sliding Door Module Ignition Off Draw (IOD) — Main EBL (Rear Window Defogger) Rear Blower
Starter Solenoid
Powertrain Control Module (PCM) Trans Range Radiator Fan
Front Wiper LO/HI
J21
J22
M1
M2
M3
M4
M5
M6
M7
Fuse 20 Amp Yellow 25 Amp Natural
Mini- Fuse
Description
Front/Rear Washer
Sunroof Module
15 Amp Blue
20 Amp Yellow 20 Amp Yellow 10 Amp Red 25 Amp Natural 20 Amp Yellow 20 Amp Yellow
Center High Mounted Stop Light (CHMSL)/ Brake Switch Trailer Lighting
Frt/Rear Axle Lockers
Trailer Tow
Inverter
Power Outlet #1/Rain Sensor Power Outlet #2
(BATT/ACC SELECT)MAINTAINING YOUR VEHICLE 399
Cavity Cartridge
Fuse
M8
M9
M10
M11
M12
Mini- Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow
10 Amp Red
30 Amp Green
Description
Cavity Cartridge
Fuse
Front Heated Seat
M13
Mini- Fuse 20 Amp Yellow
Rear Heated Seat (If Equipped) Ignition Off Draw — Vehicle Entertainment System (IOD-VES), Sat- ellite Digital Audio Re- ceiver (SDARS), DVD, Hands-Free Module (HFM), RADIO, An- tenna (ANT), Universal Garage Door Opener (UGDO), Vanity Lamp (VANITY LP) (Ignition Off Draw) IOD-HVAC/ATC, MW SENSR, Underhood Lamp (UH LMP) Amplifier (AMP)
M14
20 Amp Yellow
Description
Ignition Off Draw— Cabin Compartment Node (IOD-CCN), Wireless Control Mod- ule (WCM), SIREN, Clock Module (CLK MOD), Multifunction Control Switch (MUL- TIFCTN SW) Trailer Tow (Export Only)
400 MAINTAINING YOUR VEHICLE
Cavity Cartridge
Fuse
M15
Mini- Fuse 20 Amp Yellow
M16
10 Amp Red
Description
Cavity Cartridge
Fuse
COL MOD, IR SNS, Heater Ventilation, Air Conditioning/ Automatic Tempera- ture Control (HVAC/ ATC), Rearview Mirror (RR VW MIR), Cabin Compartment Node (CCN), Transfer Case Switch (T-CASE SW), RUN/ST, Multifunc- tion Control Switch (MULTIFTCN SW), Tire Pressure Monitor (TPM), Glow Plug Module (GLW PLG MOD) — Export Diesel Only Occupant Restraint Controller/Occupant Classification Module (ORC/OCM)
M17
M18
M19
M20
M21
M22
M23
Mini- Fuse 15 Amp Blue
15 Amp Blue
25 Amp Natural 15 Amp Blue
20 Amp Yellow 10 Amp Red 10 Amp Red
Description
Left Tail/License/Park Lamp (LT-TAIL/LIC/ PRK LMP) Right Tail/Park/Run Lamp (RT-TAIL/PRK/ RUN LMP) Auto Shut Down (ASD #1 and #2) Cabin Compartment Node Interior Light (CCN INT LIGHT), Switch Bank (SW BANK), Steering Con- trol Module (SCM) Auto Shut Down (ASD #3) Right Horn (RT HORN (HI/LOW) Left Horn (LT HORN (HI/LOW)
Cavity Cartridge
Fuse
M24
M25
M26
M27
M28
M29
Mini- Fuse 25 Amp Natural 20 Amp Yellow
10 Amp Red
10 Amp Red
10 Amp Red
10 Amp Red
Description
Cavity Cartridge
Fuse
M30
M31
M32
M33
M34
Rear Wiper (REAR WIPER) Fuel Pump (FUEL PUMP), Diesel Lift Pump (DSL LIFT PUMP) — Export Only Power Mirror Switch (PWR MIRR SW), Driver Window Switch (DRVR WIND SW) Ignition Switch (IGN SW), Window Module (WIN MOD) Next Generation Con- troller (NGC), Trans- mission Feed (TRANS FEED), J1962
Occupant Classification Module (OCM)MAINTAINING YOUR VEHICLE 401
Mini- Fuse 15 Amp Blue
20 Amp Yellow 10 Amp Red
10 Amp Red
10 Amp Red
Description
Rear Wiper Module (RR WIPER MOD), Power Folding Mirror (PWR FOLD MIR) Back-Up Lamps (B/U LAMPS) Occupant Restraint Controller (ORC), TT EUROPE Next Generation Con- troller (NGC), Global Powertrain Engine Controller (GPEC) Park Assist (PRK ASST), Heater Ventila- tion, Air Conditioning Module (HVAC MOD), Headlamp Wash (HDLP WASH), Com- pass (COMPAS)
402 MAINTAINING YOUR VEHICLE
Cavity Cartridge
Fuse
M35
M36
M37
M38
Mini- Fuse 10 Amp Red 20 Amp Yellow 10 Amp Red
25 Amp Natural
Description
Heated Mirrors
Power Outlet #3
(BATT) Anti-Lock Brake Sys- tem (ABS), Electronic Stability Program (ESP), Stop Lamp Switch (STP LP SW), Fuel Pump Rly Hi Control Lock/Unlock Motors (LOCK/UNLOCK MTRS)CAUTION!
• When installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.
MAINTAINING YOUR VEHICLE 403
REPLACEMENT LIGHT BULBS
BULB REPLACEMENT
LIGHT BULBS — Interior Bulb No. Dome Light . . . . . . . . . . . . . . . . . . . . . . . . . TL212–2
Liftgate Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
Overhead Console Lights . . . . . . . . . . . . . PLW214–2A Reading Light . . . . . . . . . . . . . . . . . . . . . . . WL212–2LIGHT BULBS — Exterior Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . 9008 H13
Front Park/Turn . . . . . . . . . . . . . . . . . . . . . . 3157AK Front Sidemarker. . . . . . . . . . . . . . . . . . . . . . . . . 168
Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057K Center High Mounted Stoplight . . . . . . . . . . . . . . 921
Fog Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . H10 9145
License Plate Light . . . . . . . . . . . . . . . . . . . . . . . 168
Rear Tail, Stop, Turn Signal. . . . . . . . . . . . . . . . 3057KHeadlight
1. Open the hood. 2. Reach behind the headlight unit in the engine com- partment to access the headlight bulb lock ring. 3. Firmly grasp the lock ring on the back of the headlight unit housing. 4. Rotate the lock ring on the back of the headlight housing counterclockwise to unlock it.
CAUTION!
Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
404 MAINTAINING YOUR VEHICLE
5. Disconnect the electrical connector and replace the bulb. Left Front Turn Signal
1. Turn the steering wheel all the way to the right (full right lock). 2. Remove the door in the left wheel liner by twisting counter clockwise. Access to the bulb can be gained through the wheel liner hole.
Access Door
3. Disconnect the electrical connector. 4. Twist the bulb counter clockwise to remove.
Right Front Turn Signal
1. Open the hood. 2. Reach behind the headlight unit in the engine com- partment to access the turn signal bulb. 3. Twist the bulb counterclockwise to remove. 4. Disconnect the electrical connector and replace the bulb. Front Side Marker
1. Open the hood. 2. Remove the grille assembly as follows:
a. Remove eight fasteners. b. Remove two screws from each headlight. c. Remove two rivets from the center of the grille. d. Remove one push pin from the top of each fender.
MAINTAINING YOUR VEHICLE 405
e. Pull the grille assembly toward you to disconnect the grille clips to the fender and the headlight ballstuds to the front end module.
3. Disconnect electrical connector. 4. Turn the bulb counterclockwise to remove. Front Fog Light (Front Fascia Mounted)
1. Reach between the front fascia and wheel liner from under the vehicle. 2. Turn the front fog light bulb one quarter turn counter- clockwise to remove from housing. 3. Disconnect the electrical connector and replace bulb.
406 MAINTAINING YOUR VEHICLE
CAUTION!
Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
Rear Tail, Stop, Turn Signal, and Backup Lights
1. Open the lift gate. 2. Remove the two push pins.
Push Pins
3. Pull lamp straight back and disconnect electrical con- nection. 4. Remove the two screws attaching the backplate to the lamp assembly. 5. Pull the backplate straight back from the lamp housing.
6. Disconnect the electrical connector. 7. Remove the bulb from the backplate. Center High Mounted Stop Light (CHMSL)
1. Remove the two screws securing the CHMSL.
MAINTAINING YOUR VEHICLE 407
2. Disconnect the electrical connector and washer hose (if equipped) from the CHMSL. 3. Replace the CHMSL.
Screw Locations
408 MAINTAINING YOUR VEHICLE
FLUID CAPACITIES
Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 4.0 Liter Engine (SAE 10W-30, API Certified) Cooling System * 3.7 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5
Year/100,000 Mile Formula) 4.0 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5
Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level.U.S.
19.5 Gallons
5 Quarts 5.5 Quarts
14 Quarts
14 Quarts
Metric
73.8 Liters
4.7 Liters 5.2 Liters
13.3 Liters
13.3 Liters
FLUIDS, LUBRICANTS AND GENUINE PARTS
MAINTAINING YOUR VEHICLE 409
Engine Component Engine Coolant
Engine Oil (3.7L Engine)
Engine Oil (4.0L Engine)
Engine Oil Filter Spark Plugs (3.7L Engine) Spark Plugs (4.0L Engine) Fuel Selection (3.7L Engine) Fuel Selection (4.0L Engine)
Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. Use API Certified SAE 10W-30 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. MOPAR威 Engine Oil Filter (P/N 04884899AB) or equivalent ZFR6F-11G (Gap 0.043 in [1.09 mm]) ZFR5LP-13G (Gap 0.050 in [1.27 mm]) 87 Octane 87 Octane Acceptable, 89 Octane Preferred
410 MAINTAINING YOUR VEHICLE
Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder
Power Steering Reservoir
Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid SAE 80W-90 Multi-Purpose Type, GL-5 Gear Lubricant or equivalent SAE 75W-140 Synthetic Gear Lubricant or equivalent MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only rec- ommended brake fluids MOPAR威 ATF+4 Automatic Transmission Fluid
MAINTENANCE SCHEDULES
CONTENTS
䡵 Emissions Control System Maintenance . . . . . . 412
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 412▫ Required Maintenance Intervals . . . . . . . . . . 414
M
412 MAINTENANCE SCHEDULES
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.
Information Center
MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation conditions the oil change indicator message will illuminate, this means that service is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illumi- nated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first.
vehicle off-road for an extended period of time.
Your dealer will reset the oil change indicator message after completing the scheduled oil change. If this sched- uled oil change is performed by someone other than your dealer the message can be reset by referring to the steps described under “Oil Change Required” in “Use Factory
MAINTENANCE SCHEDULES 413
Settings” of the EVIC section in this manual or under “Odometer/Trip Odometer” in the “Instrument Cluster Descriptions section of this manual. At Each Stop for Fuel • Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if
required.
M
414 MAINTENANCE SCHEDULES
damage.
Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. • Check all lights and other electrical items for correct
as required.
operation.
At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.
CAUTION!
Failure to perform the required maintenance items may result in damage to the vehicle.
Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
MAINTENANCE SCHEDULES 415
12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or 12 months. Inspect exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or 12 months.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ M
416 MAINTENANCE SCHEDULES
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Replace the engine air cleaner filter.
Replace the spark plugs (3.7L Engine).
❏ Adjust parking brake on vehicles
equipped with four-wheel disc brakes. Inspect the transfer case fluid.
Odometer Reading
Date
Odometer Reading
Date
Odometer Reading
Repair Order #
Dealer Code
Repair Order #
Dealer Code
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
MAINTENANCE SCHEDULES 417
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
Odometer Reading
Date
Odometer Reading
Date
Odometer Reading
Repair Order #
Dealer Code
Repair Order #
Dealer Code
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ M
418 MAINTENANCE SCHEDULES
54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter.
Replace the ignition cables (3.7L Engine). Replace the spark plugs (3.7L Engine). Inspect the brake linings; replace if necessary.
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the automatic transmission fluid and filter if using your vehicle for any of the
following: police, taxi, fleet or frequent trailer towing.
❏ Change the transfer case fluid if using your vehicle for any of the following: police, taxi,
fleet, off-road or frequent trailer towing.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
MAINTENANCE SCHEDULES 419
72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ ❏ M
420 MAINTENANCE SCHEDULES
78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.
Odometer Reading
Date
Odometer Reading
Repair Order #
Dealer Code
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter.
Inspect and replace PCV valve if necessary. † Replace the spark plugs (3.7L Engine).
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Inspect the transfer case fluid. Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 421
96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ M
422 MAINTENANCE SCHEDULES
102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
Replace the spark plugs (4.0L Engine). Replace the timing belt (4.0L Engine). Flush and replace the engine coolant.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary. Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Odometer Reading
Date
Odometer Reading
Date
